w270c

BUCKET VOLUME 4.2 m³ - 9.0 m³

BUCKET CAPACITY 8,000 kg
OPERATING WEIGHT 24,600 kg
PEAK NET POWER 320 hp
W270C
THE CLEAN ENERGY LOADER
All our C Series wheel loaders are compliant with Tier 2 interim emissions standards: to the benefit of your health
and the environment, we have reduced levels of particulate matter and of nitrogen oxides by 50%.

Increase your income

MORE PRODUCTIVE WITH 18% MORE THRUST IN 2ND SPEED
For applications such as gravel pits where 2nd speed is preferred for more grip during loading, the additional
18% penetration force will lift your productivity.

MORE PRODUCTIVE WITH MORE BUCKET RETENTION

The bucket roll back in the carry position was increased to 48° so that the material stays in your bucket during
travelling.

MORE PRODUCTIVE WITH SHORTER DISTANCES

The faster lifting of the loader enables you to position the truck at just 10 m from the pick up point.
The benefits of the shorter V-cycle are more productivity and less fuel consumption.

DECREASE YOUR EXPENSES

LESS FUEL WITH BETTER COMBUSTION
Combustion with fresh air only provides maximum efficiency, guaranteeing the best engine output delivering
more power and using less fuel.

2
CHOOSE RELIABILITY
MORE ROBUST FOR EACH APPLICATION
For the toughest jobs, reliability comes with a perfect control of the oil temperature in the axles.

• For flat hard soil such as asphalt where there is no grip issue and stress on the axle is less:
- No overheating with open differential on front and rear axles

• For soft soil where higher grip control and higher resistance are needed:
- Effective grip control with the differential lock on the front axle. It can be activated automatically or manually
controlled with the left foot.
- No overheating because the differential lock does not slip.
- Higher resistance with heavy duty front and rear axles.

For even more reliability, we have invented the COOLING BOX that keeps constant the cooling fluids temperature.

LESS MAINTENANCE WITH THE COOLING BOX

On most of the wheel loaders, the radiators are overlapping, at New Holland we have taken them and made a box
out of it. A better cooling makes longer the life of the oil by about 500 hours. With better oil wheel loader life is longer
as well.

3
W270C
WELCOME ON BOARD
OUTSTANDING VISIBILITY
You’ll feel more confident and work faster with the great all-round visibility. The low, curved rear hood shape,
provides excellent visibility.

GREAT STORAGE SPACE

The overhead radio placement and ample storage space make the cab even more convenient for you.

4
 KING SIZE ACCESS
Access to the cab is easy, safe and comfortable with 4 wide steps, 2 handles and extra wide door.
FEEL CONFIDENT WITH ROPS
All our wheel loaders’ cabs are reinforced and protect the operator against roll over (ROPS certified).
ALL CONTROLS AT YOUR FINGERTIP
T he ergonomic positioning of the control panel under your right hand puts the controls at your fi ngertips, so you
can focus on the job.

5
W270C
DIMENSIONS
W

DIMENSIONES CYCLE TIME

A - Height to top of ROPS cab 3,573 mm Raise w/rated bucket load 6.2 s
B - Wheelbase 3,550 mm Dump w/rated bucket load 1.3 s
C - Ground clearance 509.4 mm Lower (empty)
D - Angle of departure 34º Power down 2.8 s
WIDTH Float down 2.6 s
Overall* w/o bucket 2,990 mm
Centerline tread 2,250 mm
* NOTE: Dimensions taken with 26.5R25 Michelin XHA2 tires.
Turning radius* - outside 6,370 mm
TURNING ANGLE
From center 40º
Total angle 80º
Rear axle oscillation, total 24º

6
W270C
SPECIFICATIONS

Max Power Range

ENGINE TIER 2

Gross @ Rated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 hp (216 kW) @ 2100 rpm

Transmission
DRIVETRAIN

4F/3R Proportional w/Electronic Control Module torque sensing autoshift/

Peak Gross. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 hp (239 kW) @ 1800 rpm manual shift and modulation
Net @ Rated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 hp (195 kW) @ 2100 rpm Gears. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Helical cut
Peak Net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 hp (221 kW) @ 1800 rpm
NOTE: Gross horsepower and torque per SAE J1995 Torque converter
Net horsepower and torque per SAE J1349 Stall ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.99:1
Differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Open on front and rear axles
Torque Rear axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24° total
Gross . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1479 N-m @ 1200 rpm Front and rear axles
Net. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1435 N-m @ 1200 rpm Differential ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11
Torque rise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50% Planetary ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.00
Make . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . New Holland/FPT Final axle ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.67
Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2CFE614C Tier 2 certified
Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-stroke, turbocharged Special application axles (optional)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-cylinder in-line Front axle equipped with locking differential
Bore/Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 x 135 mm Rear axle equipped with open differential
Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7 l Planetaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outboard
Fuel injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct injection (electronic) 4 speed transmission travel speeds (km/h w/26.5 x 25 XHAT tires)
Fuel filter. . . . . . . . . . . . . . . . . . . . . . . . . . . Replaceable, full fl ow spin-on cartridge Forward Reverse
Fuel pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bosch CP 3.3 1st 8.0 8.0
Gradeability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35° fore /aft & side to side 2nd 13.2 4.1
Air filter. . . . . . . . . . . . . . . . . . . . 2-element dry-type w/warning restriction indicator 3rd 25.8 25.8
Rear-mount cooling module External independent mounted (non-stacked) 4th 37.4 -
coolers NOTE: Travel speeds at full engine throttle.

Fan - Hydraulic driven Parking brakes

Style. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 blade puller Spring-applied hydraulic release disc on transmission output shaft
Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876 mm
Water pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Integral Service brakes
Hydraulically actuated, maintenance-free, multiple wet disc w/accumulator to all
Engine oil four wheels
Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . Deep sump plate cooler with pressurized
under-piston nozzles Brake surface area
Front hub (each) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581 m2
Pump operating angles Rear hub (each) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 m2
Side-to-side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35°
Fore and aft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35°
Oil fi ltration. . . . . . . . . . . . . . . . . . . . . . . . . Replaceable, full flow, spin-on cartridge
OPERATING WEIGHT (kg)
Engine speeds (rpm)
Rated speed, full load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2100 Z-Bar
Horsepower Unit equipped with ROPS cab with heater and A/C, standard counterweight,
23.5R25 XHA2 tires, 4.0 m3 pin on w/bolt on edge, full fuel,
79 kg operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24,399 kg

LONG REACH
Unit equipped with ROPS cab with heater and A/C, full counterweight, 26.5R25
XHA2 tires, 4.0 m3 pin on w/bolt on edge, full fuel, 79 kg operator. . . . . 25,688 kg

7
 ELECTRICAL SYSTEM CYLINDERS
Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Volts, negative ground Lift cylinder
Alternator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 amp Bore diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177.8 mm
Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2) 900 CCA 12-Volt Rod diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114.3 mm
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 780.6 mm
Dump cylinder
Bore diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.2 mm
HYDRAULIC SYSTEM Rod diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
127.0 mm
581.9 mm
Pump (steering/implement)
Closed center pressure/flow compensated
Variable displacement, load-sensing. . . . . . . . . . . . . . . . . . . 352 l/min @ 2000 rpm
Loader control valve CAPACITIES
Closed-center, sectional 2, 3 or 4-function with pilot control for lift, tilt and
auxiliary hydraulics, electromagnetic detents in float, raise and rollback Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473 l
Loader auxiliary steering Hydraulic system
Hydraulic orbital center-pivot articulating w/on-demand oil flow Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 l
High pressure standby Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 l
Implement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25,165 kPa Transmission
Steering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24,097 kPa Service w/fi lter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45.4 l
Filtration Front and rear axle
10-micron, full flow replaceable cartridges on return line, condition indicator Front axle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.1 l
light for filter Rear axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.1 l
Engine oil w/fi lter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.3 l
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56.8 l

8
PERFORMANCE DATA
4.4 m3 FLAT
3.6 m3 BUCKET 4.2 m3 BUCKET
BOTTOM BUCKET
W270C Z-Bar w/bolt-on w/ w/bolton w/bolt-on w/ w/bolton w/bolt-on w/ w/bolton
edge teeth edge teeth edge teeth
SAE bucket capacity - struck - m3 3.11 2.96 3.63 3.49 3.80 3.65
Heaped - m3 3.63 3.49 4.20 4.06 4.40 4.23
Bucket width - outside - mm 3,195 3,195 3,195 3,195 2,980 2,980
Bucket weight - kg 2,160 2,143 2,286 2,268 2,480 2,321
E. Operating height - fully raised w/spillguard - mm 5,676 5,676 5,800 5,800 5,942 5,942
F. Hinge pin height - fully raised - mm 4,243 4,243 4,243 4,243 4,243 4,243
G. Overall length - bucket level on ground - mm 8,774 8,955 8,892 9,073 8,979 9,133
Dump angle - fully raised - grados 53 53 53 53 53 53
H. Dump height - fully raised, 45° dump - mm 3,151 3,035 3,075 2,959 3,019 2,920
J. Bucket reach - fully raised, 45° dump - mm 1,175 1,313 1,265 1,404 1,332 1,450
K. Bucket reach - 2.13 m height, 45° dump - mm 1,828 1,918 1,887 1,974 1,930 2,001
Operating load - SAE - kg 8,011 8,076 7,938 8,001 7,841 8,005
Maximum material density - SAE - kg/ m3 2,207 2,317 1,890 1,971 1,782 1,894
Tipping load - SAE
Straight - kg 19,184 19,335 19,046 19,193 18,857 19,219
40° turn - kg 16,021 16,151 15,876 16,002 15,682 16,018
Lift capacity
Full height - mm 14,143 14,130 14,027 14,016 13,840 13,950
Maximum reach - mm 20,221 20,253 20,094 20,126 19,010 20,082
Ground - mm 23,898 24,156 23,413 23,659 23,000 23,479
Breakout force w/tilt cylinder - kgf 22,616 24,406 23,413 21,922 19,092 20,963
Maximum rollback
Ground - grados 45º 45º 45º 45º 45º 45º
Carry position - grados 49º 49º 49º 49º 49º 49º
@ Maximum reach - grados 69º 69º 69º 69º 69º 69º
@ Full height - grados 65º 65º 65º 65º 65º 65º
L. Dig depth - mm 126 126 126 126 126 126
Maximum grading angle w/bucket - back dragging - grados 61 60 60 60 60 60
Loader clearance circle - mm 14,117 14,213 14,179 14,278 14,031 14,117

4.4 m3 FLAT
3.6 m3 BUCKET 4.2 m3 BUCKET
BOTTOM BUCKET
W270C Z-Bar w/bolt-on w/ w/bolton w/bolt-on w/ w/bolton w/bolt-on w/ w/bolton
edge teeth edge teeth edge teeth
E. Operating height - fully raised w/spillguard - mm 6,258 6,258 6,382 6,382 6,523 6,524
F. Hinge pin height - fully raised - mm 4,825 4,825 4,825 4,825 4,825 4,825
G. Overall length - bucket level on ground - mm 9,274 9,455 9,393 9,574 9,498 9,651
Dump angle - fully raised - grados 50 50 50 50 50 50
H. Dump height - fully raised, 45° dump - mm 3,733 3,617 3,657 3,541 3,600 3,502
J. Bucket reach - fully raised, 45° dump - mm 1,187 1,326 1,277 1,416 1,345 1,462
K. Bucket reach - 2.13 m height, 45° dump - mm 2,294 2,391 2,357 2,451 2,403 2,481
Operating load - SAE - kg 6,688 6,739 6,600 6,649 6,615 6,765
Maximum material density - SAE - kg/ m3 1,843 1,933 1,573 1,638 1,504 1,600
Tipping load - SAE
Straight - kg 16,104 16,225 15,915 16,033 15,940 16,267
40° turn - kg 13,377 13,479 13,199 13,299 13,229 13,530
Lift capacity
Full height - mm 12,525 12,519 12,405 12,401 12,426 12,546
Maximum reach - mm 17,216 17,255 17,805 17,123 17,164 17,357
Ground - mm 18,990 19,175 18,597 18,771 18,447 18,888
Breakout force w/tilt cylinder - kgf 22,835 24,643 20,654 22,135 19,282 21,170
Maximum rollback
Ground - grados 42º 42º 42º 42º 42º 42º
Carry position - grados 48º 48º 48º 48º 48º 48º
@ Maximum reach - grados 67º 67º 67º 67º 67º 67º
@ Full height - grados 66º 66º 66º 66º 66º 66º
L. Dig depth - mm 129 129 129 129 129 129
Maximum grading angle w/bucket - back dragging - grados 63° 62° 62° 62° 62° 62°
Loader clearance circle - mm 14,613 14,726 14,687 14,801 14,553 14,653

9
PARTS AND SERVICE

The New Holland dealer network is, in itself, the best

guarantee of continued productivity for the machines it
delivers to its customers.

New Holland service technicians are fully equipped to

resolve all maintenance and repair issues, with each and
every service point providing the high standards they are
obliged to observe under New Holland’s stringent quality
guidelines.

The New Holland global parts network ensures fast,

reliable, replacement parts for less downtime, increased
productivity and, of course, profitable operation for its
customers.

AT YOUR OWN DEALERSHIP

The information contained in this brochure is intended to be of general nature only. The NEW HOLLAND KOBELCO CONSTRUCTION MACHINERY S.p.A. company
may at any time and from time to time, for technical or other necessary reasons, modify any of the details or specifications of the product described in this brochure.
Illustrations do not necessarily show products in standard conditions. The dimensions, weights and capacities shown herein, as well as any conversion data used,
are approximate only and are subject to variations within normal manufacturing techniques.

NC-W27-IO1 - 07/2012

Factory: Comercial Office: Comercial Office:

Contagem – Minas Gerais – Brasil Nova Lima – Minas Gerais – Brasil Weston - Florida - 33331- USA
Av. General David Sarnoff, 2.237 Rua Senador Milton Campos, 175 / 4° andar 3265 Meridian Parkway, Suite 124
Inconfidentes – CEP 32210-900 Vila da Serra – CEP 34000-000 Teléfonos: (954) 659-2990
Teléfono: 31 2104-3111 Teléfonos: 31 2123-4902 / 31 2123-4904 (954) 659 - 2774 (FAX)