INTRODUCTION TO MADEBOQ 1

MADEBOQ means Materials Analysis Derived from Bills Of Quantities

MADEBOQ I is a programme that can calculate the quantities of materials that are required for all items of work
in an elemental bills of quantities.
MADEBOQ I presents a format that is similar to a page of a typical bills of quantities; a columned page showing
columns for serialization,description,quantity and unit. All you have to do is to input the quantities of measured
work of your elemental bills of quantities into the corresponding sections of MADEBOQ I.For example,input your
quantity for concrete in foundations against the corresponding item in MADEBOQ I section for substructure
MADEBOQ 1 calls for bulk quantities for items bearing the same specification;rather than individual items'
quantities as obtained in the bills of quantities.For example;you could have the following items with their quantities
in your bill:

S/No. Description Quantity Unit

Plain in - situ concrete (1:3:6 - 40mm aggregate) in:

A. Foundations in trenches;thickness not exceeding 100mm 23 Cu.m

B. Foundations in trenches;thickness 100 - 150mm 34 Cu.m

C. Foundations in trenches;thickness 150 - 300mm 12 Cu.m

The corresponding item in MADEBOQ 1 is :

S/No. Description Unit Quantity

In - situ concrete (1:3:6 - 40mm aggregate) in:

1 Foundations Cu.m. 69

The MADEBOQ 1 quantity for foundations is obtained by adding up the individual items of the three bills of
quantities items for foundations in trenches,that is 23 + 34 + 12 = 69 Cu.m.
Now;carefully insert your quantities in the yellow cell that is adjacent to your corresponding item
description in MADEBOQ 1.
You do this by highlighting the appropriate yellow cell, typing your quantity figure into the cell and then pressing
the ENTER key. DO NOT DELETE THE CURRENT VALUE THAT YOU MAY FIND IN THE YELLOW CELL.
By the time you start typing your new values, EXCEL will delete the current values for you.
The quantities of materials for each item will be calculated for you by MADEBOQ 1.
The figures for the quantities of materials will be outputted in the green cells.MADEBOQ 1 is also
able to calculate the total quantities of each material required in all sections of the bills of quantities.Consequently,
MADEBOQ I will give section totals (by which you will be able to ascertain the total materials required in each
element of the works) and grand totals (by which you will be able to ascertain the total quantity of materials
required for the execution of the whole works).
Scroll down to the end of each section of MADEBOQ 1 to obtain the section or elemental quantities of materials.
When you scroll down to the end of each section of MADEBOQ 1,you will be able to obtain the total quantities
of all the materials required for your works.
 CAUTION!!!
NEVER PRESS THE DELETE KEY ON ANY CELL WHATSOEVER. SOME OF THE CELLS ARE LOADED WITH
MATHEMATICAL FUNCTIONS WHICH WOULD BE ERASED IF YOU PRESS THE DELETE KEY.THUS IF YOU
WISH TO INPUT DATA IN A PARTICULAR CELL,JUST HIGHLIGHT THE CELL AND INPUT YOUR DATA,WITHO
FIRST DELETING THE CONTENTS OF THE CELL.IN THIS CASE ONCE YOU INPUT YOUR DATA,EXCEL WILL
AUTOMATICALLY REPLACE THE CURRENT DATA WITH THE NEW DATA YOU HAVE INPUTTED;AT THE SAM
THE PREVAILING MATHEMATICAL FUNTIONS WILL BE PRESERVED TO ENABLE THE PROCESSING OF YO
WORK. AS A RULE, AT THE END OF YOUR WORK, YOU COULD INPUT ZERO VALUES INTO THE INPUT CE
(THE YELLOW CELLS) TO PREPARE THE PROGRAMME TO ACCEPT NEW VALUES.
REMEMBER;NEVER PRESS THE DELETE KEY FOR WHATEVER REASON!!!
YOU SHOULD REMEMBER THE FOLLOWING:
Yellow cells are for inputting quantities for MADEBOQ 1 items
Bright green cells are for outputting quantities of materials for MADEBOQ 1 items.
Grey cells denote unit denomination for all quantities
Golden cells are for headings
Green cells are for boundaries
Turquoise cells are for margins GOOD LUCK!

MADEBOQ 1 STARTS FROM HERE

Insert Quantities from the bills of quantities here Read your quantities here
BILLS OF QUANTITIES MATERIALS' ANALYS
ELEMENT NO. 1 - SUBSTRUCTURE
s/no Description Unit Quantity Material
Hardcore fiiling
Hardcore to make up levels Cu.m. Laterite

In-situ concrete(1:3:6-40mm aggregate) Concrete (1:3:6-40mm agg.) materials

Foundation Cu.m. Cement

Other Cu.m. Sand

0
Aggregate 40mm

In situ concrete(1:2:4-18mm aggregate) In situ concrete(1:2:4-18mm aggregate)

Foundation Cu.m Cement

Bed Cu.m Sand

Column Cu.m Aggregate 18mm

Beam Cu.m

Other Cu.m
0

In situ concrete (1:10) In situ concrete (1:10)

Blinding bed Cu.m Cement
 Sand

Reinforcement Reinforcement
Bars;round mild steel (NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

20mm diameter kg 20mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Bars;high yield steel Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

19mm diameter kg 19mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Fabric reinforcement
BRC Sq.m. BRC

Formwork;sawn Formwork
General surfaces Sq.m. Plank
(NOTE:1 length of plank = 3.66 metres)
Columns and beams Sq.m.
225mm block
Sawn formwork to edges
500mm - 1.00m high Lin.m 150mm block

Sawn formwork to edges Concrete(1:3) materials for jointing

250 - 500mm high Lin.m. Cement

Sawn formwork to edges Sand

not exceeding 250mm high Lin.m.
0 Concrete(1:6) materials for filling
Brickwork and Blockwork Cement
Blockwork,sandcrete 450*230
filled solid with concrete Sand
225mm Sq.m
Concrete(1:6) materials for rendering
150mm Sq.m Cement
0
0 Sand
SUBSTRUCTURE SECTIONAL SUMMAR
Rendering Laterite
Cement and sand (1:6)
Rendering Sq.m Cement

Sand

Aggregate 40mm

Aggregate 18mm

6mm mild steel bar

8mm ditto

10mm ditto

12mm ditto

16mm ditto

20mm ditto

25mm ditto

32mm ditto

6mm high yield steel

bar

8mm ditto

10mm ditto

12mm ditto

16mm ditto
 19mm ditto

25mm ditto

32mm ditto

BRC

Plank

225mm block

END OF SUBSTRUCTURE 150mm block

ELEMENT NO. 2.FRAME MATERIALS' ANALYSIS

In situ concrete(1:2:4-18mm aggregate) In situ concrete(1:2:4-18mm aggregate)

Columns Cu.m. Cement

Beams Cu.m. Sand

0
Aggregate 18mm

Reinforcement Reinforcement
Bars;round mild steel (NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

20mm diameter kg 20mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Bars;high yield steel Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

19mm diameter kg 19mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Formwork;sawn Formwork
General surfaces Sq.m. Plank
(NOTE:1 length of plank = 3.66 metres)
Columns and beams Sq.m.
FRAME
Sawn formwork to edges SECTIONAL SUMMARY
500mm - 1.00m high Lin.m Cement

Sawn formwork to edges Sand

250 - 500mm high Lin.m.
Aggregate 18mm
Sawn formwork to edges
not exceeding 250mm high Lin.m.
0
6mm mild steel bar

8mm ditto

10mm ditto

12mm ditto

16mm ditto

20mm ditto

25mm ditto

32mm ditto

6mm high yield steel

bar

8mm ditto

10mm ditto

12mm ditto

16mm ditto

19mm ditto

25mm ditto
 32mm ditto

END OF FRAME Plank

ELEMENT NO.3 UPPER FLOORS MATERIALS' ANALYSIS

In situ concrete(1:2:4-18mm aggregate) In situ concrete(1:2:4-18mm aggregate)
Slabs Cu.m. Cement

Sand

Aggregate 18mm

Reinforcement Reinforcement
Bars;round mild steel (NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

20mm diameter kg 20mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Bars;high yield steel Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

19mm diameter kg 19mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Formwork;sawn Formwork
General surfaces Sq.m. Plank
 (NOTE:1 length of plank = 3.66 metres)
Columns and beams Sq.m.
UPPER FLOORS
Sawn formwork to edges SECTIONAL SUMMARY
500mm - 1.00m high Lin.m Cement

Sawn formwork to edges Sand

250 - 500mm high Lin.m.
Aggregate 18mm
Sawn formwork to edges
not exceeding 250mm high Lin.m.
0
6mm mild steel bar

8mm ditto

10mm ditto

12mm ditto

16mm ditto

20mm ditto

25mm ditto

32mm

6mm high yield steel

8mm ditto

10mm ditto

12mm ditto

16mm ditto

19mm ditto

25mm ditto

32mm ditto

END UPPER FLOORS Plank

ELEMENT NO.4 ROOF MATERIALS' ANALYSIS

In situ concrete(1:2:4-18mm aggregate) In situ concrete(1:2:4-18mm aggregate)

Slabs Cu.m. Cement
Upstand beams Cu.m. Sand

Roof beams Cu.m. Aggregate 18mm

Fascia Cu.m.

Other Cu.m.
0
Reinforcement Reinforcement
Bars;round mild steel (NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

20mm diameter kg 20mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Bars;high yield steel Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

19mm diameter kg 19mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Formwork;sawn Formwork
General surfaces Sq.m. Plank
(NOTE:1 length of plank = 3.66 metres)
To columns and beams Sq.m.

Sawn formwork to edges

500mm - 1.00m high Lin.m
Sawn formwork to edges
250 - 500mm high Lin.m.

Sawn formwork to edges

not exceeding 250mm high Lin.m.
0
Roofing Roofing
Corrugated sheet roofing Corrugated sheet roofing
Longspan aluminium Sq.m Long span aluminium

Longspan steel Sq.m Longspan steel

Zinc Sq.m Zinc

0

Woodwork Woodwork
Sawn hardwood Sawn hardwood
150*50mm Lin.m. 150*50mm
(NOTE: 1 length = 3.66m)
100*50mm Lin.m. 100*50mm

75*50mm Lin.m. 75*50mm

Wrought hardwood Wrought hardwood

300*19mm fascia Lin.m. 300*19mm fascia
(NOTE: 1 length = 3.66m)

Structural Steelwork
Fabricated,hot rolled steel Fabricated,hot rolled steel
angles,BS4360,Grade 43C angles,BS4360,Grade 43C
size: size:
(NOTE: 1 l length = 6.00m
50*50*6mm,3.58kg/m tonne 50*50*6mm,3.58kg/m

51*51*6.2mm,4.77kg/m tonne 51*51*6.2mm,4.77kg/m

57*57*6.2mm,5.35kg/m tonne 57*57*6.2mm,5.35kg/m

75*50*6mm,5.65kg/m tonne 75*50*6mm,5.65kg/m

76*64*9.4mm,9.68kg/m tonne 76*64*9.4mm,9.68kg/m

76*76*6.2mm,5.96kg/m tonne 76*76*6.2mm,5.96kg/m

89*64*9.4mm,10.57kg/m tonne 89*64*9.4mm,10.57kg/m

57*57*6.2mm,5.35kg/m tonne 57*57*6.2mm,5.35kg/m

Fittings and connections Fittings and connections

16mm thick mild steel end plates tonne 16mm thick mild steel end plates

10mm thick mild steel gusset 10mm thick mild steel gusset
plates tonne plates

Unframed steelwork Unframed steelwork

Steel to B.S. 4360 Grade 43 Steel to B.S. 4360 Grade 43
Zed purlin 76* 38mm*6.7 kg/m tonne Zed purlin 76* 38mm*6.7 kg/m
(NOTE: 1 l length = 6.00m
Ditto 102 * 51mm * 10.42 kg/m tonne Ditto 102 * 51mm * 10.42 kg/m

Ditto 127 * 64mm * 14.90 kg/m tonne Ditto 127 * 64mm * 14.90 kg/m

Channel 229*76mm*26.06 kg/m tonne Channel 229*76mm*26.06 kg/m

Finishes Finishes
Beds and backing Beds and backing
Cement and sand (1:4) Cement and sand (1:4)
15mm thick screeded backing Sq.m. Cement

25mm thick ditto Sq.m. Sand

0

ROOF
SECTIONAL SUMMARY
Cement

Sand

Aggregate 18mm

6mm mild steel bar

8mm ditto

10mm ditto

12mm ditto

16mm ditto

20mm ditto

25mm ditto

32mm ditto

6mm high yield steel

bar
8mm ditto

10mm ditto

12mm ditto

16mm ditto

19mm ditto

25mm ditto

32mm ditto

Formwork
Plank
(NOTE:1 length of plank = 3.66 metres)

Corrugated sheet roofing

Long span aluminium
(NOTE:1 length = 12.00 metres)
Longspan steel
(NOTE:1 length = 12.00 metres)
Zinc

Woodwork
Sawn hardwood
150*50mm
(NOTE: 1 length = 3.66m)
100*50mm

75*50mm

Wrought hardwood
300*19mm fascia
(NOTE: 1 length = 3.66m)

Fabricated,hot rolled steel

angles,BS4360,Grade 43C
size:
(NOTE: 1 l length = 6.00m
50*50*6mm,3.58kg/m

51*51*6.2mm,4.77kg/m

57*57*6.2mm,5.35kg/m

75*50*6mm,5.65kg/m
 76*64*9.4mm,9.68kg/m

76*76*6.2mm,5.96kg/m

89*64*9.4mm,10.57kg/m

57*57*6.2mm,5.35kg/m

Fittings and connections

16mm thick mild steel end plates

10mm thick mild steel gusset

plates

Steel to B.S. 4360 Grade 43

Zed purlin 76* 38mm*6.7 kg/m
(NOTE: 1 l length = 6.00m
Ditto 102 * 51mm * 10.42 kg/m

Ditto 127 * 64mm * 14.90 kg/m

Channel 229*76mm*26.06 kg/m

END OF ROOF

ELEMENT NO.5 STAIRCASES MATERIALS' ANALYSIS

In situ concrete(1:2:4-18mm aggregate) In situ concrete(1:2:4-18mm aggregate)
Staircases Cu.m. Cement

Sand

Aggregate 18mm

Reinforcement Reinforcement
Bars;round mild steel (NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

20mm diameter kg 20mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Bars;high yield steel Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

19mm diameter kg 19mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Formwork,sawn Formwork,sawn
Soffit of staircase & landings Sq.m. Plank

Edges of landing slab; not

exceeding 250mm Lin.m.

Edges of staircase flights;

maximum width 310mm Lin.m.

Edges of risers not exceeding

250mm Lin.m.
0
Finishes Finishes
Beds and backing Beds and backing
Cement and sand (1:4) Cement and sand (1:4)
25mm thick screeded backing 25mm thick screeded backing
Surfaces over 300mm wide Sq.m. Cement

Treads;300mm wide Lin.m. Sand

Risers;150mm high Lin.m.

0
In situ finishings In situ finishings
Render,cement and sand (1:6); Render,cement and sand (1:6);
15mm thick 15mm thick
Walls;internally Sq.m. Cement

Soffits of landings Sq.m. Sand

Sloping soffits of staircase Sq.m.

 String;not exceeding 300mm
girth Lin.m.
0
STAIRCASE
SECTIONAL SUMMARY
Cement

Sand

Aggregate 18mm

Reinforcement
(NOTE:1 bar length = 12.00metres)
6mm diameter

8mm diameter

10mm diameter

12mm diameter

16mm diameter

20mm diameter

25mm diameter

32mm diameter

Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter

8mm diameter

10mm diameter

12mm diameter

16mm diameter

19mm diameter

25mm diameter

32mm diameter

Formwork,sawn
END OF STAIRCASE Plank

ELEMENT NO. 6 INTERNAL AND EXTERNAL WALLS MATERIALS' ANALYSIS

Concretework Concretework
In situ concrete In situ concrete
Reinforced;(1:2:4 - 18mm agg.) Reinforced;(1:2:4 - 18mm agg.)
Beams;isolated as lintels Cu.m. Cement

Walls Cu.m. Sand

0
Aggregate

Reinforcement Reinforcement
Bars;round mild steel (NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

20mm diameter kg 20mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Bars;high yield steel Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter kg 6mm diameter

8mm diameter kg 8mm diameter

10mm diameter kg 10mm diameter

12mm diameter kg 12mm diameter

16mm diameter kg 16mm diameter

19mm diameter kg 19mm diameter

25mm diameter kg 25mm diameter

32mm diameter kg 32mm diameter

Formwork;sawn Formwork;sawn
Sides and soffits of lintels Sq.m. Plank

Blockwork Blockwork
Blockwork;sandcrete 450*230mm Blockwork;sandcrete 450*230mm
in cement and sand (1:3) in cement and sand (1:3)
150mm thick Sq.m. 150mm thick

230mm thick Sq.m. 230mm thick

0
Concrete(1:3) materials for jointing
Cement

Sand

INTERNAL AND EXTERNAL WALLS

SECTIONAL SUMMARY
Cement

Sand

Aggregate

Reinforcement
(NOTE:1 bar length = 12.00metres)
6mm diameter

8mm diameter

10mm diameter

12mm diameter

16mm diameter

20mm diameter

25mm diameter

32mm diameter

Bars;high yield steel

(NOTE:1 bar length = 12.00metres)
6mm diameter

8mm diameter

10mm diameter

12mm diameter

16mm diameter

19mm diameter
 25mm diameter

32mm diameter

Formwork;sawn
Plank

Sandcrete block

150mm thick

230mm thick

ELEMENT NO. 7 WALL FINISHES MATERIALS' ANALYSIS

Internal and External Work Internal and External Work
In situ finishings In situ finishings
Render;cement and sand (1:6) Render;cement and sand (1:6)
15mm thick 15mm thick
Over 300mm wide;including Cement
dressing all reveals,junctions and
quoins Sq.m. Sand

Curved areas Sq.m.

0
Walls;cement and sand (1:3) Walls;cement and sand (1:3)
Screeded backing;12mm thick Screeded backing;12mm thick
To receive ceramic tiles Sq.m. Cement
0
Sand
Tiles;slab and block finishings Tiles;slab and block finishings
Glazed ceramic wall tiling;
150 * 150 * 6mm Sq.m. 150*150*6mm ceramic tiles

Brick facing tiling;size Brick facing tiling;size

150 * 60 * 15mm Sq.m. 150 * 60 * 15mm

WALL FINISHES
SECTIONAL SUMMARY
Cement

Sand

150*150*6mm ceramic tiles

Carton of 150*150mm tiles

(each carton contains 88 pieces)

Brick facing tiling;size

END OF WALL FINISHES 150 * 60 * 15mm
ELEMENT NO. 8 FLOOR FINISHES MATERIALS' ANALYSIS
Internal and External Work Internal and External Work
Polished in situ terrazo paving; Polished in situ terrazo paving;
25mm thick in 1200 * 1200mm 25mm thick in 1200 * 1200mm
bays with an including black bays with an including black
ebonite strips ebonite strips
Paving internally Sq. m. Cement : marble ratio = 1:2.5
Cement
Paving externally Sq. m.
0 Marble
20 * 100mm high skirting Lin.m.
Cement : marble ratio = 1:3
Beds and backings Cement
Floors;screeded bed
25mm thick to receive quarry Marble
tiles Sq. m.
Beds and backings
25mm thick to receive Cement
terrazo paving Sq. m.
Sand
32mm thick to receive marble
tiling Sq. m. Tiles;slab and block finishings
PVC floor tiles;Dunlop 'Semtex'
32mm thick to receive granite or 'similar';300 * 300mm fixed
tiling Sq. m. with adhesive
300 * 300 *2mm PVC floor tiles
38mm thick to receive ceramic
tiling Sq. m. Carton of 300*300mm PVC tiles
(each carton contains 44 pieces)
48mm thick to receive PVC floor
tiling Sq. m. PVC floor tiles;Dunlop 'Semtex'
0 or' similar';250 * 250mm fixed
Tiles;slab and block finishings with adhesive
PVC floor tiles;Dunlop 'Semtex' 250 * 250mm PVC floor tiles
or 'similar';300 * 300mm fixed
with adhesive Carton of 250*250mm PVC tiles
Flooring;2mm thick Sq. m. (each carton contains128 pieces)

PVC floor tiles;Dunlop 'Semtex' Can of approved

or' similar';250 * 250mm fixed adhesive
with adhesive
Flooring;2mm thick Sq. m. Ebonite strip
0
Approved ceramic floor tiles; Approved ceramic floor tiles;
in cement mortar (1:3);300 * 300 in cement mortar (1:3);300 * 300
size size
Flooring;12mm thick Sq. m. Ceramic floor tiles 300*300*12mm
mm
Skirting 100mm high Lin.m.
0 Approved colour polished natural
 marble in cement mortar (1:3);
400 * 400mm size
400 * 400 *19mm
marble tiles

Approved colour polished natural

granite in cement mortar (1:3);
400 * 400mm size
Approved colour polished natural 400 * 400 *19mm
marble in cement mortar (1:3); granite tiles
400 * 400mm size
Flooring;19mm thick Sq. m. 0 FLOOR FINISHES
SECTIONAL SUMMARY
Skirting 100mm high Lin.m. Cement
0
Approved colour polished natural Marble
granite in cement mortar (1:3);
400 * 400mm size Sand
Flooring;19mm thick Sq. m. 0
300 * 300 *2mm PVC floor tiles
Skirting 100mm high Lin.m.
0 Carton of 300*300mm PVC tiles
(each carton contains 44 pieces)

250 * 250mm PVC floor tiles

Carton of 250*250mm PVC tiles

(each carton contains128 pieces)

Can of approved
adhesive

Ebonite strip

Ceramic floor tiles 225 * 225 *12

mm

400 * 400 *19mm

marble tiles

400 * 400 *19mm

END OF FLOOR FINISHES granite tiles

ELEMENT NO.9 CEILING FINISHES MATERIALS' ANALYSIS

Internal and External Work Internal and External Work
In situ finishings In situ finishings
Render;cement and sand (1:6) Render;cement and sand (1:6)
Soffits Sq.m. Cement

Plain sheet finishing Sand

6mm thick hardboard ceiling
 lining on hardwood noggins Sq.m. 0 Plain sheet finishing
0 Hardboard ceiling sheets;1200 *
600 * 600 * 12mm thick chip 2400 * 6mm thick
board ceiling boards fixed to
hardwood noggins Sq.m. Chipboard ceiling boards;600 *
0 600 * 12mm thick
Suspended ceiling
Particle board or other approved Suspended ceiling
ceiling sheets;1200 * 2400 * 12.5 Particle board or other approved
mm thick;with and including all ceiling sheets;1200 * 2400 * 12.5
timber supports;paint finish Sq.m. mm thick
0
Hardwood Hardwood
50 * 50mm noggins Lin.m. 50 * 50mm noggins
0 (NOTE: 1 length = 3.66m)
12 * 50mm battens Lin.m. 12 * 50mm battens
0 (NOTE: 1 length = 3.66m)

CEILING FINISHES
SECTIONAL SUMMARY
Cement

Sand

Hardboard ceiling sheets;1200 *

2400 * 6mm thick

Chipboard ceiling boards;600 *

600 * 12mm thick

Particle board or other approved

ceiling sheets;1200 * 2400 * 12.5
mm thick

Hardwood
50 * 50mm noggins
(NOTE: 1 length = 3.66m)
12 * 50mm battens
END OF CEILING FINISHES (NOTE: 1 length = 3.66m)

ELEMENT NO.10 PAINTING MATERIALS' ANALYSIS

Internal and External Work Emulsion paint

Prepare prime and apply three Gloss paint

full finishing coats of emulsion
paint; Whitewash primer

General surfaces;over 300mm Primer (gloss)

girth
Walls Texcote
Walls Sq.m. PAINTING
 SECTIONAL SUMMARY
Staircases Emulsion paint
Walls Sq.m.
Gloss paint
Soffits of landings Sq.m.
Whitewash primer
Sloping soffits of staircase Sq.m. (25 kg drum)
Primer (gloss)
String;not exceeding 300mm
girth Lin.m. Texcote
(30 kg drum)
Ceilings
Soffits
Suspended slab Sq.m.
0 0
Painting wood & metal;prime and
apply two full coats of gloss
paint
General surfaces;over 300mm
girth Sq.m.

Ditto;150 - 300mm Lin.m.

Ditto;not exceeding 150mm Lin.m.

0 0

Apply two full coats of texcote

paint
General surfaces;over 300mm 0 0
girth Sq.m.

Ditto;150 - 300mm Lin.m.

Ditto;not exceeding 150mm Lin.m. 0

GRAND SUMMARY OF ALL MATERIALS

Laterite trip 0

Cement bag 0

Sand trip 0

Aggregate 40mm trip 0

Aggregate 18mm trip 0

6mm mild steel bar length 0

END OF P 8mm ditto length 0

GRAND
10mm ditto length 0
S/No.
12mm ditto length 0

16mm ditto length 0

20mm ditto length 0

25mm ditto length 0

32mm ditto length 0

6mm high yield steel

bar length 0

8mm ditto length 0

10mm ditto length 0

12mm ditto length 0

16mm ditto length 0

19mm ditto length 0

25mm ditto length 0

32mm ditto length 0

BRC roll 0

Plank length 0

225mm block No. 0

150mm block No. 0

Corrugated sheet roofing

Long span aluminium Sq.m. 0
(NOTE:1 length = 12.00 metres)
Longspan steel
(NOTE:1 length = 12.00 metres)
Zinc Sq.m. 0

Woodwork
Sawn hardwood
150*50mm length 0
(NOTE: 1 length = 3.66m)
100*50mm length 0

75*50mm length 0

Wrought hardwood
300*19mm fascia length 0
(NOTE: 1 length = 3.66m)

Fabricated,hot rolled steel

angles,BS4360,Grade 43C
size:
(NOTE: 1 l length = 6.00m
50*50*6mm,3.58kg/m length 0

51*51*6.2mm,4.77kg/m length 0

57*57*6.2mm,5.35kg/m length 0

75*50*6mm,5.65kg/m length 0

76*64*9.4mm,9.68kg/m length 0

76*76*6.2mm,5.96kg/m length 0

89*64*9.4mm,10.57kg/m length 0

57*57*6.2mm,5.35kg/m length 0

Fittings and connections

16mm thick mild steel end plates Sq.m. 0

10mm thick mild steel gusset

plates Sq.m. 0

Steel to B.S. 4360 Grade 43

Zed purlin 76* 38mm*6.7 kg/m length 0
(NOTE: 1 l length = 6.00m
Ditto 102 * 51mm * 10.42 kg/m length 0

Ditto 127 * 64mm * 14.90 kg/m length 0

Channel 229*76mm*26.06 kg/m length 0

150*150*6mm ceramic tiles No. 0

Carton of 150*150mm tiles No. 0
(each carton contains 88 pieces)

Brick facing tiling;size

150 * 60 * 15mm No. 0

300 * 300 *2mm PVC floor tiles No. 0

Carton of 300*300mm PVC tiles No. 0

(each carton contains 44 pieces)

250 * 250mm PVC floor tiles No. 0

Carton of 250*250mm PVC tiles

(each carton contains128 pieces) No. 0

Can of approved
adhesive No. 0

Ebonite strip Length 0

Ceramic floor tiles 225 * 225 *12

mm No. 0

400 * 400 *19mm

marble tiles No. 0

400 * 400 *19mm

granite tiles No. 0

Hardboard ceiling sheets;1200 *

2400 * 6mm thick No. 0

Chipboard ceiling boards;600 *

600 * 12mm thick No. 0

Particle board or other approved

ceiling sheets;1200 * 2400 * 12.5
mm thick No. 0

Hardwood
50 * 50mm noggins length 0
(NOTE: 1 length = 3.66m)
12 * 50mm battens length 0
(NOTE: 1 length = 3.66m)

Emulsion paint gallon 0

Gloss paint gallon 0

Whitewash primer drum 0

Primer (gloss) gallon 0

Texcote drum 0

END OF MADEBOQ 1
ed for all items of work

lumned page showing

uantities of measured
For example,input your
n for substructure
n individual items'
tems with their quantities

f the three bills of

cell and then pressing

HE YELLOW CELL.

quantities.Consequently,
als required in each
antity of materials

quantities of materials.
in the total quantities
LLS ARE LOADED WITH
ETE KEY.THUS IF YOU
PUT YOUR DATA,WITHOUT
YOUR DATA,EXCEL WILL
E INPUTTED;AT THE SAME
HE PROCESSING OF YOUR
ES INTO THE INPUT CELLS

DEBOQ 1 items.

d your quantities here

RIALS' ANALYSIS

Unit Quantity

trip 0

m agg.) materials
bag 0

trip 0

trip 0

-18mm aggregate)
bag 0

trip 0

trip 0

bag 0
 trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

roll 0

length 0
ank = 3.66 metres)

No. 0

No. 0

als for jointing

 bag 0

trip 0

bag 0

trip 0

als for rendering

bag 0

trip 0
SECTIONAL SUMMARY
trip 0

bag 0

trip 0

trip 0

trip 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
 length 0

length 0

length 0

roll 0

length 0

No. 0

No. 0

-18mm aggregate)
bag 0

trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0
 length 0

length 0

length 0

length 0

length 0
ank = 3.66 metres)

bag 0

trip 0

trip 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
 length 0

length 0

-18mm aggregate)
bag 0

trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
ank = 3.66 metres)

bag 0

trip 0

trip 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

-18mm aggregate)
bag 0
 trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
ank = 3.66 metres)
Sq.m. 0

Sq.m. 0

sheet 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
Sq.m. 0

Sq.m. 0

length 0

length 0

length 0

length 0

bag 0

trip 0

bag 0

trip 0

trip 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
 length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
ank = 3.66 metres)

Sq.m. 0

Sq.m. 0

sheet 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0
 length 0

length 0

length 0

length 0

Sq.m. 0

Sq.m. 0

length 0

length 0

length 0

length 0

-18mm aggregate)
bag 0

trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0
 length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

No. 0

bag 0

trip 0

bag 0

trip 0
 bag 0

trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

No. 0
 bag 0

trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

No. 0

450*230mm
 No. 0

No. 0

als for jointing

bag 0

trip 0

TERNAL WALLS

bag 0

trip 0

trip 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0

length 0

length 0

= 12.00metres)
length 0

length 0

length 0

length 0

length 0

length 0
length 0

length 0

No. 0

No. 0

No. 0

bag 0

trip 0

bag 0

trip 0

No. 0

No. 0

bag 0

trip 0

No. 0

No. 0

No. 0
 bag 0

bag 0

bag 0

bag 0

bag 0

trip 0

No. 0

No. 0

No. 0

No. 0

No. 0

Length 0

0*300*12mm
No. 0

shed natural
 No. 0

shed natural

No. 0

bag 0

bag 0

trip 0

No. 0

No. 0

No. 0

No. 0

No. 0

Length 0

No. 0

No. 0

No. 0

bag 0

trip 0
 No. 0

No. 0

2400 * 12.5
No. 0

length 0

length 0

bag 0

trip 0

No. 0

No. 0

2400 * 12.5
No. 0

length 0

length 0

gallon

gallon

drum

gallon

drum
gallon 0

gallon 0

drum 0

gallon 0

drum 0