J. Basic. Appl. Sci. Res.

, 1(12)2908-2915, 2011 ISSN 2090-4304

Journal of Basic and Applied
© 2011, TextRoad Publication
Scientific Research
www.textroad.com

Analysis of Statcom Operation in Electric Transmission System

F. Gharedaghi, H. Jamali, M. Deysi, A. Khalili

Department of Electrical Engineering, Genaveh Branch, Islamic Azad University, Genaveh, Iran

ABSTRACT
A static synchronous compensator (STATCOM) is a regulating device used on alternating current
electricity transmission networks. It is based on a power electronics voltage-source converter and
can act as either a source or sink of reactive AC power to an electricity network. Usually a
STATCOM is installed to support electricity networks that have a poor power factor and often
poor voltage regulation. There are however, other uses, the most common use is for voltage
stability.The paper is based on analytical and simulation analysis, and conclusions can be used as
power industry guidelines. In this paper, We explain the principle structures of STATCOM and the
impact of this device on midpoint voltage regulation. Furthermore, the performance of the
STATCOM is compared with that of conventional static var compensator (SVC) under fault
condition. The study is thereby simulated using the MATLAB/SIMULINK software and
simulation results show that STATCOM is effective in midpoint voltage regulation on
transmission line.
Keywords: Flexible AC Transmission System (FACTS), SVC, STATCOM, Voltage Regulation.

INTRODUCTION

Flexible AC Transmission System (FACTS) is one aspect of power electronics revolution that is taking place in all
areas of electric energy. FACTS controllers use various power electronic circuit topologies or equipment that perform
certain function such as current control, power control, etc., and has the potential use in generation, transmission and
distribution of electric energy [1].
Shunt controller, therefore, is a good way to control and damp voltage oscillations by injection of leading or lagging
reactive current at and around the point of connection. There are various shunt connected FACTS devices; the major ones in
terms of applications are the static VAR compensator (SVC) and static synchronous compensator (STATCOM).
SVCs are well known to improve power system properties such as steady state stability limits, voltage regulation and
var compensation, dynamic over voltage and under voltage control, counteracting sub-synchronous resonance, and damp
power oscillations [2,3]. Voltage controlled SVC, as such, does not provide any damping to the power system [4,5].
STATCOM is basically a voltage source converter, VSC that converts a dc voltage at its input terminals into three-
phase ac voltages at fundamental frequency of controlled magnitude and phase angle. VSCs use pulse width modulation,
PWM, technology, which makes it capable of providing high quality ac output voltage to the grid or even to a passive load
[6]. STATCOM provides shunt compensation in a similar way as SVC but utilizes a voltage source converter rather shunt
capacitors and reactors [7]. The basic principle of operation of a STATCOM is the generation of a controllable AC voltage
source behind a transformer leakage reactance by a voltage source converter connected to a DC capacitor. The voltage
difference across the reactance produces active and reactive power exchanges between the STATCOM and the power
system [8]. The effect of stabilizing controls on STATCOM controllers have been investigated also in several recent
reporting [8,9].
This paper discusses about dynamic response of STATCOM and compares STATCOM and SVC under fault condition.

Basic Configuration STATCOM

An SVC provides voltage regulation and dynamic reactive power reserve by means of thyristor-controlled reactors
(TCR) and thyristor-switched capacitors (TSC) for var absorption and production respectively. A STATCOM accomplishes
the same effect by using a VSC to synthesize a voltage waveform of variable magnitude with respect to the system voltage.
The STATCOM branch offers both reactive power absorption and production capability whereas an SVC requires separate
branches for each. The STATCOM, especially when controlled with PWM, allows faster response and thereby improves
power quality. This is very useful to mitigate flicker from disturbances caused by electric arc furnaces at steel mills.

*Corresponding Author: F. Gharedaghi, Department of Electrical Engineering, Genaveh Branch, Islamic Azad University, Genaveh, Iran.
Email: [email protected]

2908
 Gharedaghi et al., 2011

One of the main reasons for installing an SVC or STATCOM in transmission networks is to increase the power transfer
capability where limited by post-contingency voltage criteria or under voltage loss of load probability. Determining the
optimum mix of dynamic and switched compensation is a challenge. Control systems are designed to keep the normal
operating point within the middle of the SVC or STATCOM dynamic range.
The voltage-sourced converter (VSC) is the basic electronic part of a STATCOM, which converts the dc voltage into a
frequency, and phase. There are different methods to realize a voltage-sourced converter for power utility application.
Based on harmonics and loss considerations, pulse width modulation (PWM) or multiple converters are used.
Inherently, STATCOMs have a symmetrical rating with respect to inductive and capacitive reactive power. For example,
the rating can be 100 Mvar inductive and 100 Mvar capacitive. For asymmetric rating, STATCOMs need a complementary
reactive power source. Fig. 1 shows Static Synchronous Compensator (STATCOM) used for midpoint voltage regulation on
a 500-kV transmission line.

Fig. 1. Static Synchronous Compensator (STATCOM) Used for Midpoint Voltage Regulation on a 500-kV Transmission Line

STATCOM Control

STATCOM, by injecting current in parallel with transmission line could control bus voltage and active power. Also,
required active power for series section is supplied by DC-link capacitor. For this purpose, the STATCOM sampling from
DC-link capacitor voltage as well as the STATCOM connected bus voltage and then by converting these values to dq0
parameters by Parks transformation and calculating voltages in per unit as follows:

= (1)
Vbus and Vdc are compared by distinct values according to the block diagram depicted in Fig. 2, and generate error signals as
follows:

Fig. 2. STATCOM control system

Generated error signals carried to PI controllers and output of PIs converted to abc parameters again and enter to
the PWM pulse generating unit. By adjusting control parameters of PI and switching, finally error signals carried to zero.
And accordingly Vbus and Vdc stabled in their reference values.

2909
 J. Basic. Appl. Sci. Res., 1(12)2908-2915, 2011

Model Description

The Static Synchronous Compensator (STATCOM) is one of the key FACTS devices. Based on a voltage-sourced
converter, the STATCOM regulates system voltage by absorbing or generating reactive power. Contrary to a thyristor-based
Static Var Compensator (SVC), STATCOM output current (inductive or capacitive) can be controlled independent of the
AC system voltage.
The power grid consists of two 500-kV equivalents (respectively 3000 MVA and 2500 MVA) connected by a 600-km
transmission line. When the STATCOM is not in operation, the "natural" power flow on the transmission line is 930 MW
from bus B1 to B3. In our demo, the STATCOM is located at the midpoint of the line (bus B2) and has a rating of +/-
100MVA. This STATCOM is a phasor model of a typical three-level PWM STATCOM. If you open the STATCOM dialog
box and select "Display Power data", you will see that our model represents a STATCOM having a DC link nominal
voltage of 40 kV with an equivalent capacitance of 375 uF. On the AC side, its total equivalent impedance is 0.22 pu on 100
MVA. This impedance represents the transformer leakage reactance and the phase reactor of the IGBT bridge.

Table1. The parameter values of the system

Parameters Values
Source voltage 500kV/50Hz
Source power 3000MVA
Total Line Length 600Km
Equivalent impedance of STATCOM 0.22 pu
Equivalent capacitance of STATCOM 375µF
Modulation frequency 1.68 kHz
DC link voltage 40 kV

SIMULATION RESULTS

1. STATCOM dynamic response

We will now verify the dynamic response of our model. Open the STATCOM dialog box and select "Display Control
parameters". Verify that the "Mode of operation" is set to "Voltage regulation" and that "External control of reference
voltage Vref" is selected. Also, the "droop" parameter should be set to 0.03 and the "Vac Regulator Gains" to 5 (proportional
gain Kp) and 1000 (integral gain KI). Close the STATCOM dialog block and open the "Step Vref" block (the red timer block
connected to the "Vref" input of the STATCOM). This block should be programmed to modify the reference voltage Vref as
follows: Initially Vref is set to 1 pu; at t=0.2 s, Vref is decreased to 0.97 pu; then at t=0.4 s, Vref is increased to 1.03; and
finally at 0.6 s, Vref is set back to 1 pu. Also, make sure that the fault breaker at bus B1will not operate during the simulation
(the parameters "Switching of phase A, B and C" should not be selected).
Run the simulation and look at the "VQ_STATCOM" scope. The Fig. 3 displays the Vref signal (magenta trace) along
with the measured positive-sequence voltage Vm at the STATCOM bus. The Fig. 4 displays the reactive power Qm
absorbed (positive value) or generated (negative value) by the STATCOM. The signal Qref (magenta trace) is not relevant to
our simulation because the STATCOM is in "Voltage regulation" and not in "Var Control".
Looking at the Qm signal we can determine that the closed-loop time constant of the system is about 20 ms. This time
constant depends primarily on the power system strength at bus B2 and on the programmed Vac Regulator gains of the
STATCOM. To see the impact of the regulator gains, multiply the two gains of the Vac Regulator Gains by two and rerun
the simulation. You should observe a much faster response with a small overshoot.
Looking at the Vm and V ref signals, you can see that the STATCOM does not operate as a perfect voltage regulator ( Vm
does not follow exactly the reference voltage Vref). This is due to the regulator droop (regulating slope) of 0.03 pu. For a
given maximum capacitive/inductive range, this droop is used to extend the linear operating range of the STATCOM and
also to ensure automatic load sharing with other voltage compensators (if any). Set the droop parameter to 0 and the voltage
regulator gains back to 5 (Kp) and 1000 (KI). If you then run a simulation, you will see that the measured voltage Vm now
follows perfectly the reference voltage Vref.

2. STATCOM compared to a SVC under fault condition

We will now compare our STATCOM model with a SVC model having the same rating (+/- 100 MVA). If you double-
click on the "SVC Power System" (the magenta block), you will see a SVC connected to a power grid similar to the power
grid on which our STATCOM is connected. A remote fault will be simulated on both systems using a fault breaker in series
with a fault impedance. The value of the fault impedance has been programmed to produce a 30% voltage sag at bus

2910
 Gharedaghi et al., 2011

B2.Before running the simulation, you will first disable the "Step Vref" block by multiplying the time vector by 100. You
will then program the fault breaker by selecting the parameters "Switching of phase A, B and C" and verify that the breaker
is programmed (look at the "Transition times" parameter) to operate at t=0.2 s for a duration of 10 cycles. Check also that
the fault breaker inside the "SVC Power System" has the same parameters. Finally, set the STATCOM droop back to its
original value (0.03 pu).
Run the simulation and look at results. Fig. 5 and Fig. 6 show active and reactive power changes. Fig. 7 shows three
phase voltage changes and Fig. 8 shows three phase current changes. Changes of Id and Iq are shown in Fig. 9 and Fig. 10.
The Fig. 12 displays the measured voltage Vm on both systems (magenta trace for the SVC). The Fig. 13 displays the
measured reactive power Qm generated by the SVC (magenta trace) and the STATCOM. During the 10-cycle fault, a key
difference between the SVC and the STATCOM can be observed. The reactive power generated by the SVC is -0.48 pu and
the reactive power generated by the STATCOM is -0.71 pu. We can then see that the maximum capacitive power generated
by a SVC is proportional to the square of the system voltage while the maximum capacitive power generated by a
STATCOM decreases linearly with voltage decrease (constant current). This ability to provide more capacitive power
during a fault is one important advantage of the STATCOM over the SVC. In addition, the STATCOM will normally
exhibit a faster response than the SVC because with the voltage-sourced converter, the STATCOM has no delay associated
with the thyristor firing (in the order of 4 ms for a SVC).
1.05
Real value
1.04
Reference value
1.03

1.02
Voltage (pu)

1.01

0.99

0.98

0.97
0 0.1 0.2 0.40.3 0.5 0.6 0.7 0.8
Time (s)
Fig. 3. Vref signal (dotted trace) along with the measured positive-sequence voltage V m at the STATCOM bus

0.5
Real value
Reference value
0.3
Reactive Power (pu)

0.1

-0.1

-0.3

-0.5
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)

Fig. 4. The reactive power Q m absorbed (positive value) or generated (negative value) by the STATCOM

2911
 J. Basic. Appl. Sci. Res., 1(12)2908-2915, 2011

950

945

940
Active Power (MW)
935

930

925

920

915

910
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 5. Changes of active power

-30

-40
Reactive Power (MVAr)

-50

-60

-70

-80

-90

-100
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 6. Changes of reactive power

1.03

1.02

1.01
Vabc (pu)

0.99

0.98
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 7. Three phase voltage changes

2912
 Gharedaghi et al., 2011

0.5

0.4

0.3
Iabc (pu)

0.2

0.1

0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 8. Three phase current changes

0.01

0.005

0
Id (pu)

-0.005

-0.01

-0.015
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 9. Reference and real values of Id

0.5

0.3

0.1
Iq (pu)

-0.1

-0.3

-0.5
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 10. Reference and real values of Iq

2913
 J. Basic. Appl. Sci. Res., 1(12)2908-2915, 2011

4
x 10
4.008

4.006

4.004

4.002
Voltage (v)

3.998

3.996

3.994

3.992
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 11. DC link voltage

1.05

0.95

0.9
Voltage (pu)

0.85

0.8

0.75
STOTCOM
0.7
SVC
0.65
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 12. Measured voltage Vm on both systems

0.4
STOTCOM
0.2
SVC
0
Reactive Power (pu)

-0.2

-0.4

-0.6

-0.8

-1

-1.2
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Time (s)
Fig. 13. The measured reactive power Qm generated by the SVC and the STATCOM

2914
 Gharedaghi et al., 2011

Conclusion

This paper illustrates in detail the principle characteristics of STATCOM. STATCOM system can be used for reactive
power compensation in the industrial network grid and under distorted mains voltage conditions, it is more reliable than
shunt capacitor reactive power compensator. We have examined the performance of SVCs and STATCOMs in electric
power systems too. Based on the analytical and simulation studies, the impact of SVCs and STATCOMs on the studied
power system is presented. It was shown that both devices significantly improve the transient voltage behavior of power
systems. Though SVCs and STATCOMs work on different principles, their impact on increasing power system
transmission capacity can be comparable.

REFERENCES

1. Hingorani N.G and L. Gyugyi, 1999. "Understanding FACTS", IEEE Press, New York.
2. Hamad A.E, 1986. "Analysis of Power System Stability Enhancement by Static VAR Compensators", IEEE Transactions
on Power Systems, 1(4): 222-227.
3. Hosseini S.H and O.Mirshekhar, 2001. "Optimal Control of SVC for Subsynchrnous Resonance Stability in Typical
Power System", Proc. ISIE, 2: 916-921.
4. Oliveria S.E.M, 1994. "Synchronizing and damping torque coefficients and power system steady state stability as
affected by static var compensators", IEEE Transactions on Power Systems, 9(1): 109-116.
5. Zhou E.Z, 1993. "Application of Static VAR Compensators to Increase Power System Damping", IEEE Transactions on
Power Systems, 8(2): 655- 661.
6. Uzunovic E, 2001. "EMTP, transient stability and power flow models and controls of VSC based facts controllers", PhD
Thesis, Waterloo University, Ontario, Canada.
7. Machowski J, 1997. "Power System Dynamics and Stability", John Wiley and Sons.
8. Wang H and F. Li, 2000. "Multivariable Sampled Regulators for the Coordinated Control of STATCOM AC and DC
Voltage", IEE Proc.- Gener. Transm. Distrib, 147(2): 93-98.
9. Wang H.F, 1999. "Phillips-Heffron Model of Power Systems Installed with STATCOM and Applications", IEE Proc.
Gener. Trans. Distr, 146(5): 521-527.

2915