Scribd
Upload
347 views10 pages

DEUTZ EMR3 Blinkcode

This document provides instructions for reading diagnostic trouble codes from a DEUTZ EMR3 system using blink codes on two different machine models - Series 3000 and Series HD. The instructions explain how to access the mainboard on each model and activate the diagnostic LED to display error codes in sequences of flashes with short breaks between. Technicians are directed to count the flashes and write down the error codes for diagnosis. The blink codes can then be looked up to determine the issue with the machine.

Uploaded by

yahir delaluz concepcion
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
347 views10 pages

DEUTZ EMR3 Blinkcode

This document provides instructions for reading diagnostic trouble codes from a DEUTZ EMR3 system using blink codes on two different machine models - Series 3000 and Series HD. The instructions explain how to access the mainboard on each model and activate the diagnostic LED to display error codes in sequences of flashes with short breaks between. Technicians are directed to count the flashes and write down the error codes for diagnosis. The blink codes can then be looked up to determine the issue with the machine.

Uploaded by

yahir delaluz concepcion
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Readout of DEUTZ EMR3 Blink-Code

Readout of DEUTZ
Blink Codes
(for machines equipped with a EMR3)

HAMM AG 1/10 # 2138392


30.11.2009
INDEX

INDEX:

1. INSTRUCTIONS FOR USE 3

1.1 LIABILITY EXCLUSION 3


1.2 IMPORTANT SYMBOLS IN THE MANUAL: 3
1.3 SECURITY ADVICE 3

2. SERIES 3000 4

2.1 PREPARATIONS 4
2.2 READOUT OF BLINK-CODES 5

3. SERIES HD 7

3.1 PREPARATIONS 7
3.2 READOUT OF BLINK-CODES 8

NOTES 10

HAMM AG 2/10 # 2138392


30.11.2009
Instructions for use

1. Instructions for use


1.1 Liability exclusion
This manual should assist service technicians with the readout of the Deutz Diagnostic
Trouble codes via Blink-Code. The general safety and accident prevention regulations ap-
ply. Company HAMM AG cannot be made liable for occurrences caused by the application
of the steps recommended in this document.

1.2 Important symbols in the manual:

! Security advices

9 Necessary information

; General information

1.3 Security advice

! Prior to starting work make sure that the battery isolation switch has been
disconnected!

HAMM AG 3/10 # 2138392


30.11.2009
Series 3000

2. Series 3000
2.1 Preparations

8 Ignition switched off!

 Open switchbox (right side of


machine)

 Disassemble four knurled nuts to


remove plastic cover

 Remove plastic cover from main-


board

HAMM AG 4/10 # 2138392


30.11.2009
Series 3000

 Mainboard with diagnose LED


and pushbutton

2.2 Readout of Blink-Codes

9 Ignition on!

8 Diesel engine switched off!!!

The blink code will appear in three flashing sequences with short breaks in
between.

9 Example:
flashing sequence = blink code
D_DD_DDD = 1-2-3

 Switch ignition on!

HAMM AG 5/10 # 2138392


30.11.2009
Series 3000

 Localize pushbutton and LED for


the readout of the EMR3 error
memory.

 Apply pushbutton until red LED


glows
 Release pushbutton and wait for
the blink code

 The blink code will appear. Example:


Please pay attention, count the flashing sequence = blink code
flashes and write down the error
codes D_DD_DDD = 1-2-3

 Apply pushbutton only for a short


click to go to the next error (if pre-
sent)

HAMM AG 6/10 # 2138392


30.11.2009
Series HD

3. Series HD
3.1 Preparations

8 Ignition switched off!

 Open switchbox (cabin floor right


side)

 Loosen two allen screws

HAMM AG 7/10 # 2138392


30.11.2009
Series HD

 Remove cover

 Mainboard with diagnose LED


and pushbutton

3.2 Readout of Blink-Codes

9 Ignition on!

8 Diesel engine switched off!!!

The blink code will appear in three flashing sequences with short breaks in
between.

9 Example:
flashing sequence = blink code
D_DD_DDD = 1-2-3

HAMM AG 8/10 # 2138392


30.11.2009
Series HD

 Switch ignition on!

 Localize pushbutton and LED for the


readout of the EMR3 error memory.

 Apply pushbutton until red LED glows


 Release pushbutton and wait for the
blink code

Beispiel:
 The blink code will appear. Please
pay attention, count the flashes and Blinksequenz = Blink-Code
write down the error codes D_DD_DDD = 1-2-3

 Apply pushbutton only for a short


click to go to the next error (if pre-
sent)

HAMM AG 9/10 # 2138392


30.11.2009
Notes

Notes

HAMM AG 10/10 # 2138392


30.11.2009

You might also like