7UM62 Generator Protection Relay

Download as pdf or txt
Download as pdf or txt
You are on page 1of 47
At a glance
Powered by AI
The document discusses the SIPROTEC 4 relay which provides generator, motor and transformer protection. It has multiple protection functions and communication capabilities to simplify engineering and ensure reliable power supply.

The SIPROTEC 4 relay can provide generator basic, generator standard and generator extended protection functions depending on the machine size and requirements. It also supports motor and transformer protection.

The SIPROTEC 4 relay uses the DIGSI 4 operating program which considerably simplifies planning, engineering and reduces commissioning times. It also allows flexible mounting and wiring for fast commissioning.

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay

Protection Systems Catalog SIP 6.2 2001

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Firmware version 4.0

Generator Protection Relay


Page Description 2 to 5

DIGSI 4 Operating program

6 and 7

Communication

8 and 9

Catalog SIP 6.2 2001

Functions Connections Typical applications

10 to 16

17 to 23

Technical data

24 to 35

Selection and ordering data

36

~ Advantages to you
n Cost-effectiveness n High degree of automation n User-friendly operation n Low planning and engineering effort n Fast, flexible mounting, reduced wiring n Simple, short commissioning n Simple spare part stocking n High flexibility n High reliability and availability n State-of-the-art technology n Compliance with international standards n Integration in a control system

Accessories

37

Connection diagrams

38 to 41

Dimension drawings

42 and 43

Siemens AG 2001 Siemens SIP 6.2 2001

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Description Application The 7UM6 protection relays of the SIPROTEC 4 range are compact multifunction units which have been developed for small, medium and large power generation plants. They incorporate all the necessary protective functions and are especially suitable for the protection of: Hydro and pumped-storage generators Cogeneration stations Private power stations using regenerative energy sources such as wind or biogases Power generation with diesel generators Gas turbine power stations Industrial power stations and Steam power stations. They can also be employed for protection of motors and transformers. The numerous other additional functions assist the user in ensuring cost-effective system management and reliable power supply. Measured values display current operating conditions. Stored status indications and fault recording provide assistance in fault diagnosis not only in the event of a disturbance in generator operation. Combination of the units makes it possible to implement effective redundancy concepts. Uniform design The SIPROTEC 4 units have a uniform design and a degree of functionality which represents a whole new quality in protection and control. Local operation has been designed according to ergonomic criteria. Large, easy-to-read displays were a major design aim. The DIGSI 4 operating program considerably simplifies planning and engineering and reduces commissioning times. Highly reliable The 7UM6 hardware is based on 20 years of Siemens experience with numerical protection equipment. State-of-the-art technology and a high-efficiency 32-bit microprocessor are employed. Production is subject to exacting quality standards. Special attention has been paid to electromagnetic compatibility and the number of electronic modules has been drastically reduced by the use of highly integrated circuits. The software design incorporates accumulated experience and the latest technical knowledge. Object orientation and high-level language programming, combined with the continuous quality assurance system, ensure maximized software reliability. Programmable logic The integrated programmable logic function allow the user to implement his own functions for automation of switchgear (interlocking) via a graphic user interface. The user can also generate user defined messages. Adjustments can easily be made to the varying power station requirements. Protection functions Numerous protection functions are necessary for reliable protection of electrical machines. Their extent and combination are determined by a variety of factors, such as machine size, mode of operation, plant configuration, availability requirements, experience and design philosophy. This leads of necessity to multifunctionality, which is implemented in outstanding fashion by numerical technology. In order to satisfy differing requirements, the combination of functions is scalable (see Table 1). Selection is facilitated by division into five groups. Generator Basic One application concentrates on small and medium generators for which differential protection is required. The function mix is also suitable as backup protection. Protection of synchronous motors is a further application. Generator Standard In the case of medium-size generators (10 to 100 MVA) in a unit connection, this scope of functions offers all necessary protection functions. Besides inadvertent energization protection, it also includes powerful backup protection for the transformer or the power system. The scope of protection is also suitable for units in the second protection group. Generator Full Here, all protection functions are available and the main application focuses on large block units (more than 100 MVA). The function mix includes all necessary protection functions for the generator as well as backup protection for the block transformer including the power system. Additional functions such as protection during start-up for generators with starting converters are also included. The scope of functions can be used for the second protection group, and functions that are not used can be masked-out. Motor Asynchronous Besides differential protection, this function package includes all protection functions needed to protect large asynchronous motors (more than 1 MVA). Stator and bearing temperatures are measured by a separate RTD module and are transmitted serially to the protection unit for evaluation. Transformer This scope of functions not only includes differential and overcurrent protection, but also a number of protection functions that permit monitoring of voltage and frequency stress, for instance. The reverse-power protection can be used for energy recovery monitoring of parallel-connected transformers.

Siemens SIP 6.2 2001

Protection functions

Abbreviation I

ANSI-N

Generator Basic X X X X X X X X X X X X X 4 X X X X X X X

GeneGenerator rator Standard Full X X X X X X X X X X X X X 4 X X X X X X X X X X X X X X X X X X X X X X X 4 X X X X X X X X X X X X X X

Motor Asynchronous X X X X X X X X X X X X X 4 X X X X X X

Transformer X X X X X X X X X X X X X 4 X X

Current differential protection Stator earth-fault protection non-directional, directional Sensitive earth-fault protection (also rotor earth-fault protection) Stator overload protection Definite time-overcurrent protection with undervoltage seal-in Definite time-overcurrent protection, directional Inverse time-overcurrent protection Overvoltage protection Undervoltage protection Frequency protection Reverse-power protection Overexcitation protection (Volt/Hertz) Fuse failure monitor External trip coupling Trip circuit supervision Forward-power protection Underexcitation protection (loss-of-field protection) Negative sequence protection Breaker failure protection Motor starting time supervision Restart inhibit for motors Rotor earth-fault protection (fn, R-measuring) Inadvertent energization protection 100% stator earth-fault protection with 3rd harmonics Impedance protection with (I>+V<) pick-up DC voltage / DC current time protection Overcurrent protection during start-up (for gas turbines)2) Earth-current differential protection2) Out-of-step protection Rotor earth-fault protection ( 1 to 3 Hz square wave voltage)2) 100 % stator earth-fault protection with 20 Hz voltage2) Rate-of-frequency-change protection2) Vector jump supervision (voltage) Supervision of phase rotation Undercurrent via CFC External temperature monitoring via serial interface2)
2)

87G/87T/ 87M 59N, 64G 67G 50/51GN (64R) 49 51 50/51/67 51V 59 27 81 32R 24 60FL 74TC 32F 40 46 50BF 48 66, 49 Rotor 64R (fn) 50/27 59TN, 27TN 3rd h 21 59N (DC) 51N (DC) 51 87GN/TN 78 64R (1 3 Hz) 64G (100%) 81R 47 37 38

V0>, 3I0> (V0, 3I0)


IEE> I2t I> +V< I>>, Direc.

t = f (I)+V< V> V<, t=f(V) f<, f> P V/f V2/V1, I2/I1 Incoup. T.C.S. P>, P< 1/xd I2>, t =f(I2) Imin> Istart2t I2t R<
I>, V< V0(3rd harm.)

Z< Vdc > Idc > I>


Ie Z/t

RREF< RSEF<
df/dt > > A, B, C I< (RTD)

X1) X1) X1) X X X X


1)

X1) X1) X1) X


1)

X1) X1) X1) X1) X X X X X X X X X

X X X

Table 1: Scope of functions of the 7UM62

1) Optional for all function groups 2) Available as of version V4.1 and higher Siemens SIP 6.2 2001

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Description Measurement Based on years of experience, high-efficiency protection algorithms have been implemented which are adapted especially to generator behavior. Thus, irrespective of the generator frequency at the time, a high degree of measurement accuracy is achieved by virtue of the sampling frequency correction in the range of 11 to 69 Hz. Filter algorithms suppress the higher frequency transient phenomena and aperiodic DC components. Unit configuration The units are available in 2 versions as the 7UM621 in 19-inch and the 7UM622 in 1/ 19-inch width. The software 1 functions and subassembly breakdown are identical. The 7UM622 possesses more binary inputs and outputs and is suitable for incorporation in older or more complex plants. Communication The 7UM62 units possess up to four serial interfaces: Front interface for connecting a PC Service interface for connecting a PC via modem System interface for connecting to a control system via IEC 60870-5-103, PROFIBUS-DP; MODBUS RTU Additional interface for special applications and an input for Time synchronization via IRIG B or DCF77. Operational measured values In order to assist system management and for commissioning purposes, all relevant measured values are displayed as primary and secondary values with unit and values relating to the object to be protected. The measured values can also be transferred via the serial interfaces. In addition, the programmable logic permits limit value scans and status indications derived therefrom. Metered values are available in the form of energy metered values for the active and reactive energy supplied and are also provided by an elapsedhour meter. Operational indications The SIPROTEC 4 units provide extensive data for fault analysis, as well as control. All indications listed below are protected against power supply failure. Fault indications The last eight faults are stored in the unit at all times. A fresh fault erases the oldest one. The fault indications possess a time resolution of 1 ms. They provide detailed information on fault history. The buffer memory is designed for a total of 600 indications. Operational indications All indications that are not directly associated with the fault (e.g. operating or switching actions) are stored in the status indication buffer. The time resolution is 1 ms, buffer size: 200 indications. Temperature monitoring By means of a separate RTD module up to 6 temperatures can be monitored by means of temperature sensors. They are transferred via a serial interface to the protection unit, where they are processed. Temperature evaluation is designed for twelve measuring points, and so two temperature monitoring units can be connected. Temperatures are optionally evaluated in C or F. PT 100, Ni 100 and Ni 120 can be used as temperature sensors. Measuring transducers Three measuring transducers are available in the protection unit. If they are not needed by the protection functions, they can be used to inject in any chosen analog signals ( 10V, 0 to 20 mA). Thus, signals from pressure sensors and vibration meters etc. can be evaluated. Threshold and logical processing take place in the Continuous Function Chart (CFC) (see page 7). Fault recording up to 5 or 80 seconds An instantaneous value or RMS value recorder is provided. The firmware permits storage of 8 fault recordings. Triggering can be effected by means of pickup, tripping, binary input, the DIGSI 4 operating program or by the control system. In the case of the instantaneous value recording, the input variables (4 x v and 8 x i ) and the 3 transducer values are recorded at increments of 1.25 ms at 50 Hz or 1.04 ms at 60 Hz. The total duration is 5 seconds. If the time is exceeded, the oldest fault recording in each case is overwritten. If protection functions with long delay times are activated, the RMS value recording is recommended. Storage of relevant calculated variables (V1, VE, I1, I2, IEE1, IEE2, P, Q, , R, X, f-fn) takes place at increments of one cycle. The total time is 80 seconds. Time synchronization A battery-backed clock is a standard component and can be synchronized via a synchronization signal (DCF77; IRIG B via satellite receiver), binary input, system interface or SCADA (e.g. SICAM). A date and time are assigned to every indication. Freely assignable binary inputs and outputs Binary inputs, output relays and the LEDs are assignable with indications, user-specifically and independently of one another. The tripping matrix is implemented by means of the firmware. It is simplicity itself to set the tripping programs. The firmware assists primary testing by functional suppression of the trip command. Continuous self-monitoring The hardware and software are continuously monitored. If abnormal conditions are detected, the unit signals immediately. In this way, a great degree of safety, reliability and availability is achived. Reliable battery monitoring The battery buffers the indications and fault recordings in the event of power supply voltage failure. Its function is checked at regular intervals by the processor. If the capacity of the battery is found to be declining, an alarm indication is generated. All setting parameters are stored in the Flash-EPROM which are not lost if the power supply or battery fails. The SIPROTEC 4 unit remains fully functional.

Siemens SIP 6.2 2001

n Operation User-friendly local operation Many advantages are already to be found on the clear and user-friendly front panel: n Positioning and grouping of the keys supports the natural operating process n Large non-reflective back-lit display n Programmable (freely assignable) LEDs for important messages

n Arrows arrangement of the keys for easy navigation in the function tree n Operator-friendly input of the setting values via the numeric keys or DIGSI 4 n Four programmable keys for frequently used functions >at the press of a button< Local operation All operator actions can be executed and information displayed on an integrated user interface:
Fig. 1 SIPROTEC 4 7UM62

On the LCD display, process and device information can be displayed as text in various lists. Frequently displayed information includes protection setting values, metered values, protection information, general indications and alarms as well as binary information on inputs and outputs.
t

Fourteen configurable (parameterizable) LEDs are used to display any process or device information. The LEDs can be labeled based on user requirements. An LED reset key resets the LEDs.
LSP2287-afpen.eps

s s s

RS232 operator interface

Four configurable function keys permit the user to execute frequently used actions fast and simple. Typical applications include jumps to certain points in the menu tree to display the operational measured values or indications.

Keys for navigation

Numerical operation keys

Siemens SIP 6.2 2001

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


DIGSI 4 Operating program DIGSI 4, the PC program for operating protection relays The PC operating program DIGSI 4 is the interface between the user and the SIPROTEC 4 units. It has a modern, intuitive operator interface. With DIGSI 4, the SIPROTEC 4 units can be configured and queried - it is a tailored program for the energy supply and manufacturing industries. The software runs under Windows (Version 95 and higher, as well as NT).

Fig. 2 DIGSI 4, main menue

Fig. 3 DIGSI 4, some protection functions

DIGSI 4 matrix The DIGSI 4 matrix allows the user to see the overall view of the unit configuration at a glance. For example, you can display all the LEDs that have binary inputs or show any indication that are connected to the relay. And with one click of the button connections can be switched. By utilizing filter functions, only allocated information is rendered visible. In addition, it is possible to alter the viewing modes. In Binary Output viewing mode (output relays), the tripping matrix is clearly displayed.
LSP295-afpen2.tif

Fig. 4 DIGSI 4, allocation matrix

Siemens SIP 6.2 2001

LSP2294-afpen.tif

Simple protection setting The protection functions required can be selected from the wide range of functions provided (Fig. 3). This means that transparency in subsequent menus is enhanced. The newly introduced primary display (settings are related to nominal values of the object to be protected) permits standardization of the setting values. Pressing a button effects conversion to secondary values and loading into the protection unit.

LSP2293-afpen.tif

CFC: Reduced time and planning for programming logic With the help of the CFC (Continuous Function Chart), you can configure interlocks and switching sequences simply by drawing the logic sequences; no special knowledge of software is required. Logical elements, such as AND, OR and time elements, measured limit values, etc. are available. Commissioning Special attention has been paid to commissioning. All binary inputs and outputs can be read and set directly. This can simplify the wire checking process significantly for the user. For primary testing, it is possible to activate a transmission lockout to prevent any information being transmitted via the interface to the control room. On the other hand, indications can be transmitted intentionally for test purposes. SIGRA 4: Universal program for fault recording evaluation Fault recordings stored in the protection system can be visually displayed and evaluated in clear form. It is easily possible to calculate harmonics, to view individual measuring points, to display vector and locus diagrams etc. The Comtrade format makes it possible to analyze any desired fault recordings.

Fig. 5 CFC logic with module library

Fig. 6 Fault recording

DIGS The new ~

I4

learn n Easy to matrix f routing t r layout o n Clea equipmen eder and tion, fe n Substa nagement data ma on d protecti TIC Passwor n AM/SIMA ith the SICent w n Linked e environm ar softw tandards indows s nW

LSP2182f.tif

LSP2181f.tif

Siemens SIP 6.2 2001

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Communication With respect to communication, particular emphasis is placed on high levels of flexibility, data integrity and utilization of standards common in energy automation. The design of the communication modules permits interchangeability on the one hand, and on the other hand provides openness for future standards (for example, Industrial Ethernet). Local PC interface The PC interface accessible from the front of the unit permits quick access to all parameters and fault event data. Of particular advantage is the use of the DIGSI 4 operating program during commissioning. Rear-mounted interfaces On the rear of the unit are one fixed interface and two communication modules which incorporate optional equipment complements and readily permit retrofitting. They assure the ability to comply with the requirements of different communication interfaces (electrical or optical) and protocols (IEC 60870, PROFIBUS, DIGSI). The interfaces make provision for the following applications: Service interface (fixed) In the RS485 Version, several protection units can be centrally operated with DIGSI 4. On connection of a modem, remote control is possible. This provides advantages in fault clearance, in particular in unmanned power stations. System interface This is used to carry out communication with a control or protection and control system and supports, dependent on the module connected, a variety of communication protocols and interface designs. Additional interface Via this interface communication with the RTD modules is made possible. IEC 60870-5-103 IEC 60870-5-103 is an internationally standardized protocol for the efficient solving of communication problems in the protected area. IEC 60870-5-103 is supported by a number of protection unit manufacturers and is used world-wide. The generator protection functions are stored in the private part (published) of the protocol. PROFIBUS-DP PROFIBUS is an internationally standardized communication system (EN 50170) for communication problem solving. PROFIBUS is supported internationally by several hundred manufacturers and has to date been used in more than 1,000,000 applications all over the world. With the PROFIBUS-DP the protection can be directly connected to a SIMATIC S5/S7. The transferred data are fault data, measured values and information from or to the logic (CFC). MODBUS RTU MODBUS is also a widely utilized communication standard and is used in numerous automation solutions. Safe bus architecture n RS485 bus With this data transmission via copper conductors electromagnetic fault influences are largely eliminated by the use of twisted-pair conductor. Upon failure of a unit, the remaining system continues to operate without any faults. n Fiber-optic double ring circuit The fiber-optic double ring circuit is immune to electromagnetic interference. Upon failure of a section between two units, the communication system continues to operate without disturbance.

Fig. 7 IEC 60870-5-103 star-type RS232 copper conductor connection or fibre-optic connection

OLM1)

Fig. 8 PROFIBUS: Optical double ring circuit

Fig. 9 PROFIBUS: RS485 copper conductors

1) Optical Link Module

Siemens SIP 6.2 2001

System solution SIPROTEC 4 is tailor-made for use in SIMATIC-based automation systems. Via the PROFIBUS-DP, indications (pickup and tripping) and all relevant operational measured values are transmitted from the protection unit. Via modem and service interface, the protection engineer has access to the protection devices at all times. This permits remote maintenance and diagnosis (cyclic testing). Parallel to this, local communication is possible, for example during a major inspection. Analog output 0 to 20 mA Alternatively to the serial interfaces up to two analog output modules (4 channels) can be installed in the 7UM62. Several operational measured values (I1, I2, V, P, Q, f, PF (cos ), stator, rotor) can be selected and transmitted via the 0 to 20 mA interfaces.

Fig. 10 Communication module, optical

LSP2162f.eps

Fig. 11 Communication module, optical, double-ring

LSP2163f.eps

Fig. 12 Communication module RS232, RS485

Fig. 13 Analog output module 0 to 20 mA, 2 channels

Fig. 14 System solution: Communications

LSP2207f.eps

LSP2164f.eps

Siemens SIP 6.2 2001

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Functions Current differential protection (ANSI 87G, 87M, 87T) This function provides undelayed short-circuit protection for generators, motors and transformers, and is based on the current differential protection principle (Kirchhoffs current law). The differential and restraint (stabilization) current are calculated on the basis of the phase currents. Optimized digital filters reliably attenuate disturbances such as aperiodic component and harmonics. The high resolution of measured quantities permits recording of low differential currents (10% of IN) and thus a very high sensitivity. An adjustable restraint characteristic permits optimum adaptation to the conditions of the protected object. Software is used to correct the possible mismatch of the current transformers and the phase angle rotation through the transformer (vector group). Thanks to harmonic analysis of the differential current, inrush (second harmonic) and overexcitation (fifth harmonic) are reliably detected, and unwanted operation of the differential protection is prevented. The current of internal short-circuits is reliably measured by a fast measuring stage (IDiff>>), which operates with two mutually complementary measuring processes. An external shortcircuit with transformer saturation is picked up by a saturation detector with time and status monitoring. It becomes active when the differential current (IDiff) moves out of the add-on restraint area. If a motor is connected, this is detected by monitoring the restraint current and the restraint characteristic is briefly raised. This prevents false tripping in the event of unequal current transmission by the current transformers. Figure 15 shows the restraint characteristic and the varions areas.

Fig. 15 Restraint characteristic of current differential protection

Fig. 16 Restraint characteristic of earth-current differential protection

Earth-current differential protection (ANSI 87GN, 87TN) The earth current differential protection permits high sensitivity to single-pole faults. The zero currents are compared. On the one hand, the zero sequence current is calculated on the basis of the phase currents and on the other hand, the earth current is measured directly at the star point current transformer.

The differential and restraint quantity is generated and is fitted into the restraint characteristic (see Fig. 16). DC components in particular are suppressed by means of specially dimensioned filters. A number of monitoring processes avoid unwanted operation in the event of external short-circuits. In the case of a sensitive setting, multiple measurement ensures the necessary reliability.

However, attention must be drawn to the fact that the sensitivity limits are determined by the current transformers. The protection function is only used on generators when the neutral point is earthed with a low impedance. In the case of transformers, it is connected on the neutral side. Lowimpedance or solid earthing is also required.

10

Siemens SIP 6.2 2001

Definite time-overcurrent protection I>, I>> (ANSI 50, 51, 67) This protection function comprises the short-circuit protection for the generator and also the backup protection for upstream devices such as transformers or power system protection. An undervoltage stage at I> maintains the pickup when during the fault the current drops below the threshold. In the case of a voltage drop on the generator terminals, the static excitation system can no longer be sufficiently supplied. This is one reason for the decreasing of the short-circuit current. The I>> stage can be implemented as high-set instantaneous trip stage. With the integrated directional function it can be used as backup protection on the transformer high voltage side. With the information of the directional element, impedance protection can be controlled via the CFC. Inverse time-overcurrent protection (ANSI 51V) This function also comprises short-circuit and back-up protection and is used for power system protection with current dependent protection devices. IEC and ANSI characteristics can be selected (Table 2). By evaluating the generator terminal voltage, the current function can be controlled. The controlled version releases the sensitive set current stage. With the restraint version the pickup value of the current is lowered linearly with decreasing voltage. The fuse-failure-monitor prevents unwanted operation.

Stator overload protection (ANSI 49) The task of the overload protection is to protect the stator windings of generator and motors from high, continuous overload currents. All load variations are evaluated by a mathematical model. The thermal effect of the rms current value forms the basis of the calculation. This conforms to IEC 60255-8. In dependency of the current the cooling time constant is automatically extended. If the ambient temperature or the temperature of the coolant are injected via a transducer (TD2) or PROFIBUS-DP, the model automatically adapts to the ambient conditions; otherwise a constant ambient temperature is assumed. Negative sequence protection (ANSI 46) Asymmetrical current loads in the three phases of a generator cause a temperature rise in the rotor because of the negative sequence field produced. This protection detects an asymmetrical load in threephase generators. It functions on the basis of symmetrical components and evaluates the negative sequence of the phase currents. The thermal processes are taken into account in the algorithm and form the inverse characteristic. In addition, the negative sequence is evaluated by an independent stage (alarm and trip) which are supplemented by a time-delay element (see Fig. 17). In the case of motors, the protection function is also used to monitor a phase failure.

Fig. 17 Characteristic of negative sequence protection

IEC characteristic Normal inverse 0.14 t= Tp 0 , 02 I 1 I p Very inverse 13.5 t= Tp 1 I 1 I p Extremely inverse 80 t= Tp 2 I I 1 p

ANSI characteristic Inverse 8.9341 t= + 0.17966 D 2 . 0938 I 1 I p Moderately inverse 0.0103 t= + 0.0228 D 0 . 02 I 1 Ip Very inverse 3.922 t= + 0.0982 D 2 I 1 I p Extremely inverse 5.64 t = + 0.02434 D 2 I 1 I p Definite inverse 0.4797 t= + 0.21359 D 1. 5625 I 1 Ip

Table 2 Inverse-time characteristics (IP - Pickup value; TP, D - Time dial)

Siemens SIP 6.2 2001

11

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Functions Underexcitation protection (loss-of-field protection) (ANSI 40) Derived from the generator terminal voltage and current, the complex admittance is calculated and corresponds to the generator diagram scaled in per unit. This protection prevents damage due to loss of synchronism resulting from underexcitation. The protection function provides three characteristics for monitoring static and dynamic stability. Via a transducer, the excitation voltage (see Fig. 25) can be injected and , in the event of failure, a swift reaction of the protection function can be achieved by timer changeover. The straight-line characteristics allow an optimum adaption of the protection to the generator diagram (see Figure 18). The per-unit-presentation of the diagram allows direct read-out of the setting values. The positive sequence systems of current and voltage are used to calculate the admittance. This ensures that the protection always operates correctly even with asymmetrical network conditions. In the case of a voltage deviation from the rated voltage, the admittance calculation has the advantage that the characteristics move in the same direction as the generator diagram. Reverse-power protection (ANSI 32R) The reverse-power protection monitors the direction of active power flow and picks up when the mechanical energy fails. This function can be used for operational shutdown (sequential tripping) of the generator but also prevents damage to the steam turbines. The reverse power is calculated from the positive-sequence systems of current and voltage. Asymmetrical power system faults therefore do not cause reduced measuring accuracy. The position of the emergency trip valve is injected as binary information and is used to switch between two trip command delays. When applied for motor protection, the sign (+ / ) of the active power can be reversed via parameters. Forward-power protection (ANSI 32F) Monitoring of the active power produced by a generator can be useful for starting up and shutting down generators. One stage monitors exceeding of a limit value while another stage monitors falling below another limit value. The power is calculated using the positive-sequence component of current and voltage. The function can be used to shut down idling motors. Impedance protection (ANSI 21) This fast short-circuit protection protects the generator, the unit transformer and is a backup protection for the power system. This protection has two settable impedance stages; in addition, the first stage can be switched over via binary input. With the circuitbreaker in the open position (see Fig. 19) the impedance measuring range can be extended. The overcurrent pickup element with under-voltage seal-in ensures a reliable pickup and the loop selection logic ensures a reliable detection of the faulty loop. With this logic it is possible to perform correct measuring via the unit transformer. Undervoltage protection (ANSI 27) The undervoltage protection evaluates the positive-sequence components of the voltages and compares them with the threshold values. There are two stages available The undervoltage function is used for asynchronous motors and pumped-storage stations and prevents the voltagerelated instability of such machines. The function can also be used for monitoring purposes.

Fig. 18 Characteristic of underexcitation protection

Fig. 19 Grading of impedance protection

12

Siemens SIP 6.2 2001

Overvoltage protection (ANSI 59) This protection prevents insulation faults that result when the voltage is too high. Either the maximum line-to-line voltages or the phase-to-earth voltages (for low-voltage generators) can be evaluated. The measuring results of the line-to-line voltages are independent of the neutral point displacement caused by earth faults. This function is implemented in two stages. Frequency protection (ANSI 81) The frequency protection prevents an unpermissible stress of the equipment (e.g. turbine) in case of under or overfrequency. It also serves as an monitoring and control element. The function has four stages; the stages can be implemented either as underfrequency or over-frequency protection. Each stage can be delayed separately. Even in the case of voltage distortion, the frequency measuring algorithm reliably identifies the fundamental waves and determines the frequency extremely precise. Frequency measurement can be blocked by using an undervoltage stage. Overexcitation protection Volt/Herz (ANSI 24) The overexcitation protection serves for detection of an unpermissible high induction (proportional to V/f) in generators or transformers, which leads to a thermal overloading. This may occur when starting up, shutting down under full load, with weak systems or under isolated operation. The inverse characteristic can be set via eight points derived from the manufacturer data. In addition, a definite-time alarm stage and an instantaneous stage can be used. For calculation of the V /f ratio, frequency and also the highest of the three line-to-line voltages are used. The frequency range that can be monitored comprises 11 to 69 Hz.

90 % stator earth-fault protection, non-directional, directional (ANSI 59N, 64G, 67G) Earth faults manifest themselves in generators that are operated in isolation by the occurance of a displacement voltage. In case of unit connections, the displacement voltage is an adequate, selective criterion for protection. For the selective earth-fault detection, the direction of the flowing earth-current has to be evaluated too, if there is a direct connection between generator and busbar. The protection relay measures the displacement voltage at a v.t. located at the transformer star point or at the broken delta-winding of a v.t. As an option it is also possible to calculate the zero-sequence voltage from the phase-to-earth voltages. Depending on the load resistor selection 90 to 95 % of the stator winding of a generator can be protected. A sensitive current input is available for the earth current measurement. This input should be connected to a core-balance current transformer. The fault direction is deduced from the displacement voltage and earth current. The directional characteristic (straight line) can be easily adapted to the system conditions. Effective protection for direct connection of a generator to a busbar can therefore be created. During startup, it is possible to switch over from the directional to the displacement voltage measurement via an externally injected signal. Depending on the protection setting, various earth-fault protection concepts can be implemented with this function (see Figs. 23 to 26).

Fig. 20 Logic diagram of breaker failure protection

Sensitive earth-fault protection (ANSI 50/51GN, 64R) The sensitive earth-current input can also be used as separate earth-fault protection. It is of two-stage form. Secondary earth currents of 2 mA or higher can be reliably handled. Alternatively, this input is also suitable as rotor earth-fault protection. A voltage with rated frequency (50 or 60 Hz) is connected in the rotor circuit via the interface unit 7XR61. If a higher earth current is flowing, a rotor earth fault has occurred. Measuring circuit monitoring is provided for this application (see Fig. 29). 100% stator earth-fault protection with 3rd harmonic (ANSI 59TN, 27TN (3rdH.)) Owing to the design, the generator produces a 3rd harmonic that forms a zero phasesequence system. It is verifiable by the protection on a broken delta winding or on the neutral transformer. The magnitude of the voltage amplitude depends on the generator and its operation. In the event of an earth fault in the vicinity of the neutral point there is a change in the amplitude of the 3rd harmonic voltage (dropping in the neutral point and rising at the terminals).

Depending on the connection the protection must be set either as undervoltage or overvoltage protection. It can also be delayed. So as to avoid overfunction, the active power and the positive sequence voltage act as enabling criteria. The final protection setting can be made only by way of a primary test with the generator. Breaker failure protection (ANSI 50BF) In the event of scheduled downtimes or a fault in the generator, the generator can remain on line if the circuitbreaker is defective and could suffer substantial damage. Breaker failure protection evaluates a minimum current and the circuit-breaker auxiliary contact. It can be started by internal protective tripping or externally via binary input. Two-channel activation avoids overfunction (see Figure 20).

Siemens SIP 6.2 2001

13

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Functions Inadvertent energization protection (ANSI 50, 27) This protection has the function of limiting the damage of the generator in the case of an unintentional switch-on of the circuit-breaker whether the generator is standing still or rotating without being excited or synchronized. If the power system voltage is connected the generator starts as an asynchronous machine with a large slip and this leads to excessively high currents in the rotor. A logic circuit consisting of sensitive current measurement for each phase, measured value detector, time control and blocking as of a minimum voltage, leads to an instantaneous trip command. If the fuse failure monitor responds, this function is ineffective. Rotor earth-fault protection (ANSI 64R) This protection function can be realized in three ways with the 7UM62. The simplest form is the method of rotor current measurement (see sensitive earth-current measurement). Resistance measurement at system-frequency voltage The second form is rotor earth resistance measurement with voltage at system frequency (see typical applications in Fig. 29). This protection measures the voltage injected and the flowing rotor earth current. Taking into account the complex impedance from the coupling device (7XR61), the rotor earth resistance is calculated by way of a mathematical model. By means of this method, the disturbing influence of the rotor earth capacitance is eliminated, and sensitivity is increased. Fault resistance values up to 30 k can be measured if the excitation voltage is without disturbances. Thus, a two-stage protection function can be realized which features a warning and a tripping stage. An additionally implemented undercurrent stage monitors the rotor circuit for open circuit and issues an alarm. Resistance measurement with a square wave voltage of 1 to 3 Hz. A higher sensitivity is required for larger generators. On the one hand, the disturbing influence of the rotor earth capacitance must be eliminated more effectively and, on the other hand, the noise ratio with respect to the harmonics (e.g. sixth harmonic) of the excitation equipment must be increased. Injecting a low-frequency square wave voltage into the rotor circuit has proven itself excellently here (see typical applications, Fig. 30). The square wave voltage injected through the controlling unit 7XT71 leads to permanent recharging of the rotor earth capacitance. By way of a shunt in the controlling unit, the flowing earth current is measured and is injected into the protection unit (measurement input). In the absence of a fault ), (RE the rotor earth current after charging of the earth capacitance is close to zero. In the event of an earth-fault, the fault resistance including the coupling resistance (7XR6004), and also the injecting voltage, defines the stationary current. The current square wave voltage and the frequency are measured via the second input (control input). Fault resistance values up to 80 k can be measured by this measurement principle. The rotor earth circuit is monitored for discontinuities by evaluation of the current during the polarity reversals. 100% stator earth-fault protection with 20 Hz injection (ANSI 64 G (100%)) Injecting a 20 Hz voltage to detect earth-faults even at the neutral point of generators has proven to be a safe and reliable method. Contrary to the third harmonic criterion (see page 12, Catalog SIP 6.1), it is independent of the generators characteristics and the mode of operation. Measurement is also possible during system standstill. Fig. 28 shows the basic method of connection. This protection function is designed so as to detect both earth faults in the entire generator (genuine 100%) and all electrically connected system components. The protection unit measures the injected 20 Hz voltage and the flowing 20 Hz current. The disturbing variables, for example stator earth capacitance, are eliminated by way of a mathematical model, and the ohmic fault resistance is determined. On the one hand, this ensures high sensitivity and, on the other hand, it permits use of generators with large earth capacitance values, e.g. large hydroelectric generators. Phase-angle errors through the earthing or neutral transformer are measured during commissioning and are corrected in the algorithm. The protection function has a warning and tripping stage. The measurement circuit is also monitored and failure of the 20 Hz generator is measured. Independently of earth resistance calculation, the protection function additionally evaluates the amount of the rms current value. Starting time supervision (motor protection only) (ANSI 48) Starting time supervision protects the motor against long unwanted start-ups, that might occur when excessive load torque occurs, excessive voltage drops occur within the motor or if the rotor is locked. The tripping time is dependent on the square of the start-up current and the set start-up time (Inverse Characteristic). It adapts itself to the start-up with reduced voltage. The tripping time is determined in accordance with the following formula: I t Trip = start tstart max Irms
2

tTrip Istart

Tripping time Permissible start-up current tstart max Permissible start-up time Measured rms current Irms value Calculation is not started until the current Irms lies above an adjustable response value (e.g. 2 IN, MOTOR). If the permissible locked-rotor time is less than the permissible start-up time (motors with a thermally critical rotor), a binary signal is set to detect a locked rotor by means of a tachometer generator. This binary signal releases the set locked-rotor time, and tripping occurs after it has elapsed.

14

Siemens SIP 6.2 2001

DC voltage time protection/DC current time protection (ANSI 59N (DC) 51N(DC)) Hydroelectric generators or gas turbines are started by way of frequency starting converters. An earth fault in the intermediate circuit of the frequency starting converter causes DC voltage displacement and thus a direct current. As the neutral or earthing transformers have a lower ohmic resistance than the voltage transformers, the largest part of the direct current flows through them, thus posing a risk of destruction from thermal overloading. As shown in Fig. 28, the direct current is measured by means of a shunt transformer (measuring transducer) connected directly to the shunt. Voltages or currents are fed to the 7UM62 depending on the version of the measuring transducer. The measurement algorithm filters out the DC component and takes the threshold value decision. The protection function is active as from 0 Hz. If the measuring transducer transmits a voltage for protection, the connection must be interference-free and must be kept short. The implemented function can also be used for special applications. Thus, the rms value can be evaluated for the quantity applied at the input over a wide frequency range. Overcurrent protection during start-up (ANSI 51) Gas turbines are started by means of frequency starting converters. Overcurrent protection during start-up measures shortcircuits in the lower frequency range (as from about 5 Hz) and is designed as independent overcurrent-time protection. The pick-up value is set below the rated current. The function is only active during start-up. If frequencies are higher than 10 Hz, sampling frequency correction takes effect and the further shortcircuit protection functions are active.

Out-of-step protection (ANSI 78) This protection function serves to measure power swings in the system. If generators feed to a system short-circuit for too long, low frequency transient phenomena (active power swings) between the system and the generator may occur after fault clearing. If the center of power swing is in the area of the block unit, the active power surges lead to unpermissible mechanical stressing of the generator and the turbine. As the currents and voltages are symmetrical, the positive sequence impedance is calculated on the basis of their positive-sequence components and the impedance trajectory is evaluated. Symmetry is also monitored by evaluation of the negative-phase-sequence current. Two characteristics in the R/X diagram describe the active range (generator, unit transformer or power system) of the out-of-step protection. The associated counters are incremented depending on the range of the characteristic in which the impedance vector enters or departs. Tripping occurs when the set counter value is reached. The counters are automatically reset if power swing no longer occurs after a set time. By means of an adjustable pulse, every power swing can be signaled. Expansion of the characteristic in the R direction defines the power swing angle that can be measured. An angle of 120 is practicable. The characteristic can be tilted over an adjustable angle to adapt to the conditions prevailing when several parallel generators feed into the system.

Fig. 21 Characteristics of the out-of-step protection

Inverse undervoltage protection (ANSI 27) Motors tend to fall out of step when their torque is less than the breakdown torque. This, in turn, depends on the voltage. On the one hand, it is desirable to keep the motors connected to the system for as long as possible while, on the other hand, the torque should not fall below the breakdown level. This protection task is realized by inverse undervoltage protection. The inverse characteristic is started if the voltage is less than the pick-up threshold Vp<. The tripping time is inversely proportional to the voltage dip (see equation). The protection function uses the positive-sequence voltage, for the protection decision.

System disconnection E.g., in-plant generators feed directly into a system. The incoming line is generally the legal entity boundary between the system owner and the in-plant generator. If the incoming line fails as the result of auto-reclosure, for instance, a voltage or frequency deviation may occur depending on the power balance at the feeding generator. Asynchronous conditions may arise in the event of connection, which may lead to damage on the generator or the gearing between the generator and the turbine. Besides the classic criteria such as voltage and frequency, the following two criteria are also applied (vector jump, rate-of-frequencychange protection, see page 16).

t TRIP =

I I

V Vp

T M

tTRIP V Vp TM

Tripping time Voltage Pick-up value Time multiplier

Siemens SIP 6.2 2001

15

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Functions Vector jump Monitoring the phase angle in the voltage is a criterion for identifying an interrupted infeed. If the incoming line should fail, the abrupt current discontinuity leads to a phase angle jump in the voltage. This is measured by means of a delta process. The command for opening the generator or coupler circuit-breaker is issued if the set threshold is exceeded. Rate-of-frequency change protection (ANSI 81) The frequency difference is determined on the basis of the calculated frequency over a time interval. It corresponds to the momentary rate-of- frequency change. The function is designed so that it reacts to both positive and negative rate-of- frequency changes. Exceeding of the permissible rate-of- frequency change is monitored constantly. Release of the relevant direction depends on whether the actual frequency is above or below the rated frequency. In total, four stages are available, and can be used optionally. Restart inhibit for motors (ANSI 66, 49Rotor) When cold or at operating temperature, motors may only be connected a certain number of times in succession. The start-up current causes heat development in the rotor which is monitored by the restart inhibit function. Contrary to classical counting methods, in the restart inhibit function the heat and cooling phenomena in the rotor are simulated by a thermal replica. The rotor temperature is determined on the basis of the stator currents. Restart inhibit permits restart of the motor only if the rotor has enough thermal reserve for a completely new start. Fig. 22 shows the thermal profile for a permissible triple start out of the cold state. If the thermal reserve is too low, the restart inhibit function issues a blocking signal with which the motor starting circuit can be blocked. The blockage is cancelled again after cooling down and the thermal value has dropped below the pick-up threshold.

Fig. 22 Temperature characteristic at rotor and in thermal replica of the rotor (multiple start-ups)

As the fan provides no forced cooling when the motor is off, it cools down more slowly. Depending on the operating state, the protection function controls the cooling time constant. A value below a minimum current is an effective changeover criterion. External trip coupling For recording and processing of external trip information there are 4 binary inputs. They are provided for information from the Buchholz relay or generator-specific commands and act like a protective function. Each input initiates a fault event and can be individually delayed by a timer. Trip circuit supervision (ANSI 74TC) One or two binary inputs can be used for monitoring the circuit-breaker trip coil including its incoming cables. An alarm signal occurs whenever the circuit is interrupted. Phase rotation reversal If the relay is used in a pumped-storage power plant, matching to the prevailing rotary field is possible via a binary input (generator/motor operation via phase rotation reversal).

2 pre-definable parameter groups In the protection the setting values can be stored in two datasets. In addition to the standard parameter group, the second group is provided for certain operating conditions (pumped-storage power stations). It can be activated via binary input, local control or DIGSI 4. Lockout (ANSI 86) All binary outputs (alarm or trip relays) can be stored like LEDs and reset using the LED reset key. The lockout state is also stored in the event of supply voltage failure. Reclosure can only occur after the lockout state is reset.

Fuse failure and other monitoring The relay comprises high-performance monitoring for the hardware and software. The measuring circuits, analog-digital conversion, power supply voltages, memories and software sequence (watchdog) are all monitored. The fuse failure function detects failure of the measuring voltage due to short-circuit or open circuit of the wiring or v.t. and avoids overfunction of the undervoltage elements in the protection functions. The positive and negative-sequence system (voltage and current) are evaluated. Filter time All binary inputs can be subjected to a filter time (indication suppression).

16

Siemens SIP 6.2 2001

Connections/Typical applications Direct generator-bus connection Fig. 23 illustrates the recommended standard connection if several generators supply one busbar. Phase-to-earth faults are disconnected by employing the directional earth-fault criterion. The earth-fault current is driven through the cables of the system. If this is not sufficient, an earthing transformer connected to the busbar supplies the necessary current (maximum approximately 10 A) and permits a protection range of up to 90 %. The earth-fault current should be detected by means of core-balance current transformers in order to achieve the necessary sensitivity. The displacement voltage can be used as earth-fault criterion during starting operations until synchronization is achieved. Differential protection embraces protection of the generator and of the outgoing cable. The permissible cable length and the current transformer design (permissible load) are mutually dependent. Recalculation is advisable as from lengths of more than 100 m.

Fig. 23

Siemens SIP 6.2 2001

17

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Connections/Typical applications Direct generator-bus connection with low-resistance earthing If the generator neutral point has low-resistance earthing, the connection illustrated in Fig. 24 is recommended. In the case of several generators, the resistance must be connected to only one generator, in order to prevent circulating currents (3rd harmonic). For selective earth-fault detection, the earth-current input should be looped into the common return conductor of the two current transformer sets (differential connection). The current transformers must be earthed at only one point. The displacement voltage VE is utilized as additional enable criterion. Balanced current transformers (calibration of windings) are desirable with this form of connection. In the case of higher generator power (for example, IN approximately 2000 A), current transformers with a secondary rated current of 5 A are recommended. Earth-current differential protection can be used as an alternative (not illustrated).

Fig. 24

18

Siemens SIP 6.2 2001

Unit connection with isolated star point This configuration of unit connection is a variant to be recommended (see Figure 25). Earth-fault detection is effected by means of the displacement voltage. In order to prevent unwanted operation in the event of earth faults in the system, a load resistor must be provided at the broken delta winding. Depending on the plant, a voltage transformer with a high power (VA) may in fact be sufficient. If not, an earthing transformer should be employed. The available measuring winding can be used for the purpose of voltage measurement. In the application example, differential protection is intended for the generator. The unit transformer is protected by its own differential relay (e.g. 7UT612). As indicated in the figure, additional protection functions are available for the other inputs. They are used on larger generator/transformer units (see also Figs. 28 and 30).

Fig. 25

Siemens SIP 6.2 2001

19

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Connections/Typical application Unit connection with neutral transformer With this system configuration, disturbance voltage reduction and damping in the event of earth faults in the generator area are effected by a load resistor connected to the generator neutral point (see Fig. 26). The maximum earth-fault current is limited to approximately 10 A. Configuration can take the form of a primary or secondary resistor with neutral transformer. In order to avoid low secondary resistance, the transformation ratio of the neutral transformer should be V low Gen 500 V . The higher 3 secondary voltage can be reduced by means of a voltage divider. Electrically, the circuit is identical to the above configuration (Fig. 25). In the application opposite, the differential protection is designed as an overall function and embraces the generator and unit transformer. The protection function takes care of vector group adaptation as well as other adaptations.

Fig. 26

20

Siemens SIP 6.2 2001

Voltage transformer in open delta connection (V-connection) Protection can also be readily implemented on voltage transformers in open delta connection. Fig. 27 shows the connection involved. If necessary, the operational measured values for the phase-to-earth voltages can be slightly asymmetrical. If this is undesirable, the neutral point (R16) can be connected to earth via a capacitor. In the case of open delta connection, it is not possible to calculate the displacement voltage from the secondary voltages. It must be passed to the protection unit along a different path (for example, voltage transformer at the generator neutral point or from the earthing transformer). 100% stator earth-fault protection, earth-fault protection during start-up With reference to the example of the neutral transformer, Fig. 28 shows interfacing of 100% stator earth-fault protection with voltage injection of 20 Hz. The same interfacing connection also applies to the broken delta winding of the earthing transformer. The 20 Hz generator can be connected both to the DC voltage and also to a powerful voltage transformer (>100 VA). The load of the current transformer 4NC1225 should not exceed 0.5 . The 7XT33, 7XT34 and load resistance connection must be established with a low resistance (RConnection < RL). If large distances are covered, the devices are accommodated in the earthing cubicle. Connection of the DC voltage protection function (TD 1) is shown for systems with a starting converter. Depending on the device selection, the 7KG6 boosts the measured signal at the shunt to 10 V or 20 mA. The TD 1 input can be jumpered to the relevant signal.

Fig. 27

Fig. 28

Siemens SIP 6.2 2001

21

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Connections/Typical application Rotor earth-fault protection with voltage injection at rated frequency By way of example, Fig. 29 shows connection of rotor earth-fault protection to a generator with static excitation. If only the rotor current is evaluated, there is no need for voltage connection to the relay. Earth must be connected to the earthing brush. The external resistors 3PP136 must be added to the coupling device 7XR61 if the circulating current can exceed 0.2 A as the result of excitation (sixth harmonic). Under worst-case conditions, this is the case as from a rated excitation voltage of >150 V. Rotor earth-fault protection with a square wave voltage of 1 to 3 Hz The measuring transducers TD1 and TD2 are used for this application (Fig. 30). The controlling unit 7XT71 generates a square wave voltage of about 50 V at the output. The frequency can be jumpered and depends on the rotor earth capacitance. Voltage polarity reversal is measured via the control input and the flowing circular current is measured via the measurement input. Earth must be connected to the earthing brush.

Fig. 29

Fig. 30

22

Siemens SIP 6.2 2001

Protection of an asynchronous motor Fig. 31 shows typical connection of the protection function to a large asynchronous motor. Differential protection embraces the motor including the cable. Recalculation of the permissible current transformer burden is advisable as from lengths of more than 100 m. The voltage for voltage and displacement voltage monitoring is generally tapped off the busbar. If several motors are connected to the busbar, earth faults can be detected with the directional earth-fault protection and selective tripping is possible. A core balance current transformer is used to detect the earth current. The chosen pickup value must be slightly higher if there are several cables in parallel. The necessary shutdown of the motor in the event of idling can be realized with active power monitoring.

Fig. 31

Siemens SIP 6.2 2001

23

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Connections/Typical application Use of selected analog inputs Several protection functions take recourse to the same analog inputs, thus ruling out certain functions depending on the application. One input may only be used by one protection function. A different combination can be used by the unit belonging to Protection Group 2, for example. Multiple use refers to the sensitive earth-current inputs and the displacement voltage input (see Table 3). The same applies to the measuring transducers (Table 4). Current transformer requirements The requirements imposed on the current transformer are determined by the differential protection function. The instantaneous trip stage (I Diff>>) reliably masters (via the instantaneous algorithm) any highcurrent internal short-circuits. The external short-circuit determines the requirements imposed on the current transformer as a result of the DC component. The non-saturated period of a flowing short-circuit current should be at least 5 ms. The tables opposite show the design recommendations. IEC 60044-1 and 60044-6 were taken into account. The necessary equations are shown for converting the requirements into the knee-point voltages. The customary practice which presently applies should also be used to determine the rated primary current of the current transformer rated current. lt should be greater than or equal to the rated current of the protected object.

IEE1 Sensitive earth-fault protection Directional stator earth-fault protection Rotor earth-fault protection (fn, R-measuring) 100% stator earth-fault protection with 20 Hz voltage Earth-current differential protection
1) optional (eitherIEE1 or IEE2) Table 3: Multiple use of analog inputs

IEE2 X1) X

VE

X1)

X X X

X X X1) X1)

TD1 Injection of excitation voltage DC voltage time/DC current time protection Injection of a temperature Rotor earth-fault protection (1 to 3 Hz) Processing of analog values via CFC
Table 4: Multiple use of measuring transducers

TD2

TD3 X

X X X X X X X

Accuracy limiting factor


Required actual accuracy limiting factor K *ALF = K td I pSSC I pN Resulting rated accuracy limiting factor K ALF =

R BC + R Ct K *ALF R BN + R Ct

Current transformer requirements


Transformer Transient dimensioning factor Ktd Symmetrical short-circuit current IpSSC Example Note: Identical transformers have to be imployed 4 N 100 ms 1 I pN,Tr v SC Generator > (4 to 5) N > 100 ms 1 I pN,G x "d

vSC = 0.1 K*ALF > 40


Rated power 10 or 15 VA Example: Network transformer 10P10: (10 or 15) VA (IsN = 1 A or 5 A)

xd = 0.12 K*ALF > (34 to 42)


Note: Secondary winding resistance Example: IN, G approx. 1000 to 2000 A 5P15: 15 VA (IsN = 1 A or 5 A) IN, G > 5 000 A 5P20: 30 VA (IsN = 1 A or 5 A)

Knee-point voltage
IEC British Standard ANSI

V = K ALF (R Ct + R BN )I sN
Ktd IpSSC IpN

V=

(R

Ct

+ R BN )I sN 1,3

K ALF

K V = 20 I sN (R Ct + R BN ) ALF 20 I sN = 5A (typical value)

rated transient dimensioning factor primary symmetrical short-circuit current rated primary current transformer current connected burden resistance rated burden resistance secondary winding resistance short-circuit voltage (impedance voltage) subtransient reactance rated secondary current transformer current network time constant

RBC RBN RCt vSC xd IsN N

Table 5: Recommendations for dimensioning

24

Siemens SIP 6.2 2001

Technical data

Hardware
Analog input Rated frequency Rated current IN Earth current, sensitive IEmax Rated voltage VN (at 100 V) Measuring transducer Power consumption with IN = 1 A with IN = 5 A for sensitive earth current voltage inputs (with 100 V) Capability in CT circuits thermal (rms values) 50 or 60 Hz 1 or 5 A 1.6 A 100 to 125 V - 10 to + 10 V (Ri = 1 M) or - 20 to + 20 mA (Ri = 10 ) approx. 0.05 VA approx. 0.3 VA approx. 0.05 VA approx. 0.3 VA 100 IN for 1 s 30 IN for 10 s 4 IN continuous 250 IN (one half cycle) 300 A for 1 s 100 A for 10 s 15 A continuous 750 A (one half cycle) 230 V continuous 60 V continuous 100 mA continuous 24 to 48 V DC 60 to 125 V DC 110 to 250 V DC and 115 V AC with 50/60 Hz 20 to +20 % 15 % approx. 5.3 W approx. 5.5 W approx. 12 W approx. 15 W 50 ms 20 ms 7 15 14 to 19 V DC or 66 to 88 V DC 300 V DC approx. 1.8 mA 12 (1 NO; 4 optional as NC via jumper) 21 (1 NO; 5 optional as NC via jumper) 1000 W / VA 30 VA 40 W 25 VA 250 V 5 A continuous 30 A for 0.5 seconds 1 1 14

dynamic (peak) Earth current, sensitive dynamic (peak) Capability in voltage paths Capability of measuring transducer as voltage input as current input Power supply Rated auxiliary voltage

Permitted tolerance Superimposed (peak to peak) Power consumption during normal operation 7UM621 7UM622 during pickup with all inputs and outputs activated 7UM621 7UM622 Bridging time during auxiliary voltage failure at Vaux = 48 V and Vaux 110 V at Vaux = 24 V and Vaux = 60 V Binary inputs Number 7UM621 7UM622 2 pickup thresholds Range is selectable with jumpers Maximum permissible voltage Current consumption, energized Number 7UM621 7UM622 Switching capacity make break break (for resistive load) break (for L/R 50 ms) Switching voltage Permissible current Number RUN (green) ERROR (red) Assignable LED (red)

Output relays

LED

Siemens SIP 6.2 2001

25

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Technical data

Unit version

7XP20 housing Degree of protection acc. to EN 60529 For surface-mounting housing For flush-mounting housing front rear For the terminals Weight Flush-mounting housing 7UM621 (1/2 x 19 ) 7UM622 (1/1 x 19l) Surface-mounting housing 7UM621 (1/2 x 19) 7UM622 (1/1 x 19)

For dimensions see dimension drawings IP 51 IP 51 IP 50 IP 2x with terminal cover put on

approx. 7 kg approx. 9.5 kg approx. 12 kg approx. 15 kg

Serial interfaces
Operating interface for DIGSI 4 Connection Baud rate Time synchronization IRIG B / DCF 77 signal Connection Voltage levels Service/modem interface (Port C) for DIGSI 4 / Modem / Service System interface (Port B) IEC 60870-5-103 PROFIBUS DP MODBUS RTU Isolated RS232/RS485 Test voltage Distance for RS232 Distance for RS485 Isolated RS232/RS485 Baud rate Test voltage Permissible distance for RS232 Permissible distance for RS485 PROFIBUS RS485 Test voltage Baud rate Permissible distance PROFIBUS fiber-optic cable Baud rate Optical wavelength Permissible path attenuation Bridgeable distance Analog output module (electrical) Non-isolated, RS232, front panel; 9-pin subminiature connector 4800 to 115200 Bauds 9-pin subminiature connector, terminal with surface-mounting case selectable 5 V, 12 V or 24 V 9-pin subminiature connector 500 V / 50 Hz Max. 15 m Max. 1000 m 9-pin subminiature connector 4800 to 115200 Bauds 500 V / 50 Hz Max. 15 m Max. 1000 m 500 V / 50 Hz Max. 12 MBauds 1000 m at 93,75 kBauds; 100 m at 12 MBauds Integrated ST-connector; Single or double ring Max. 1.5 MBauds = 820 nm Max. 8 dB for glass-fiber 62.5/125 m Max. 1.5 km 2 ports with 0 to 20 mA

Electrical tests
Specifications Standards IEC 60255 (product standards) ANSI/IEEE C37.90.0/.1/.2 UL 508 DIN 57435 part 303 For further standards see below IEC 60255-5 2.5 kV (rms.), 50/60 Hz

Insulating tests

Standards Voltage test (100 % test) All circuits except for auxiliary supply, binary inputs communication and time synchronization interfaces Voltage test (100 % test) Auxiliary voltage and binary inputs Voltage test (100 % test) only isolated communication interfaces and time synchronization interface Surge voltage test (type test) All circuits except for communication interfaces and time synchronization interface, class III

3.5 kV DC 500 V (rms value), 50/60 Hz 5 kV (peak); 1.2/50 s; 0.5 J; 3 positive and 3 negative surges at intervals of 5 s

26

Siemens SIP 6.2 2001

EMC tests for noise immunity (type test)

Standards

High frequency test IEC 60255-22-1, class III and DIN 57435 part 303, class III Discharge of static electricity IEC 60255-22-2 class IV EN 61000-4-2, class IV Exposure to RF field, non-modulated IEC 60255-22-3 (report), class III Exposure to RF field, amplitude-modulated IEC 61000-4-3, class III Exposure to RF field, pulse-modulated IEC 61000-4-3/ ENV 50204, class III Fast transient interference bursts IEC 60255-22-4, IEC 61000-4-4, class IV High-energy surge voltages (SURGE), IEC 61000-4-5 installation class III Auxiliary supply Measurement inputs, binary inputs and relay outputs Conducted RF, amplitude-modulated IEC 61000-4-6, class III Magnetic field with power frequency IEC 61000-4-8, class IV; IEC 60255-6 Oscillatory surge withstand capability ANSI/IEEE C37.90.1 Fast transient surge withstand capability ANSI/IEEE C37.90.1 Radiated electromagnetic interference ANSI/IEEE C37.90.2 Damped oscillations IEC 60894, IEC 61000-4-12 EMC tests for interference emission (type tests) Standard Radio interference voltage on lines only auxiliary supply IEC-CISPR 22 Interference field strength IEC-CISPR 22

IEC 60255-6, IEC 60255-22 (product standards) EN 50082-2 (generic standard) DIN 57 435 part 303 2.5 kV (peak value), 1 MHz; = 15 ms 400 pulses per s; duration 2 s 8 kV contact discharge; 15 kV air discharge; both polarities; 150 pF; Ri = 330 10 V/m; 27 to 500 MHz 10 V/m; 80 to 1000 MHz; 80 % AM; 1 kHz 10 V/m; 900 MHz; repetition frequency 200 Hz; duty cycle 50 % 4 kV; 5/50 ns; 5 kHz; burst length = 15 ms; repetition frequency 300 ms; both polarities; Ri = 50 ; test duration 1 min Impulse: 1.2/50 s common (longitudinal) mode: 2 kV; 12 , 9 F differential (transversal) mode:1 kV; 2 , 18 F common (longitudinal) mode: 2 kV; 42 , 0.5 F differential (transversal) mode: 1 kV; 42 , 0.5 F 10 V; 150 kHz to 80 MHz; 80 % AM; 1 kHz 30 A/m continuous; 300 A/m for 3 s; 50 Hz 0.5 mT; 50 Hz 2.5 to 3 kV (peak); 1 to 1.5 MHz damped wave; 50 surges per second; Duration 2 s; Ri = 150 to 200 4 to 5 kV; 10/150 ns; 50 impulses per second; both polarities; duration 2 s ; Ri = 80 35 V/m; 25 to 1000 MHz 2.5 kV (peak value), polarity alternating 100 kHz, 1 MHz, 10 and 50 MHz, Ri = 200 EN 50081-1 (generic standard) 150 kHz to 30 MHz class B 30 to 1000 MHz class B

Mechanical dynamic tests


Vibration and shock stress at stationary conditions Standards Vibration IEC 60255-21-1, class 2 IEC 60068-2-6 IEC 60255-21 and IEC 60068 Sinusoidal 10 to 60 Hz: 0.075 mm amplitude; 60 to 150 Hz: 1 g acceleration Frequency sweep 1 octave/min 20 cycles in 3 orthogonal axes Half-sinusoidal Acceleration 5 g, duration 11 ms, 3 shocks each in both directions of the 3 axes Sinusoidal 1 to 8 Hz: 3.5 mm amplitude (horizontal axis) 1 to 8 Hz: 1.5 mm amplitude (vertical axis) 8 to 35 Hz: 1 g acceleration (horizontal axis) 8 to 35 Hz: 0,5 g acceleration (vertical axis) Frequency sweep 1 octave/min 1 cycle in 3 orthogonal axes

Shock IEC 60255-21-2, class 1 IEC 60068-2-27 Vibration during earthquake IEC 60255-21-2, class 1 IEC 60068-3-3

Siemens SIP 6.2 2001

27

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Technical data

Vibration and shock test during transport

Standards Vibration IEC 60255-21-1, class 2 IEC 60068-2-6

Shock IEC 60255-21-2, class 1 IEC 60068-2-27 Continuous shock IEC 60255-21-2, class 1 IEC 60068-2-29 Climatic stress Temperatures Standards Recommended temperature during operation Temporary permissible temperature limit during operation Limit temperature during storage Limit temperature during transport Storage and transport with standard factory packaging Humidity

IEC 60255-21 and IEC 60068-2 Sinusoidal 5 to 8 Hz: 7,5 mm amplitude; 8 to 150 Hz: 2 g acceleration Frequency sweep 1 octave/min 20 cycles in 3 orthogonal axes Half-sinusoidal Acceleration 15 g, duration 11 ms, 3 shocks each in both directions 3 axes Half-sinusoidal Acceleration 10 g, duration 16 ms, 1000 shocks in both directions of the 3 axes IEC 60255-6 - 5 to +55 C 25 to 131 F - 20 to +70 C - 4 to 158 F (The legibility of the display may be affected above 55 C/131 F) 25 to +55 C -13 to 131 F 25 to +70 C -13 to 158 F

Permissible humidity stress Annual average 75 % relative humidity; on 56 We recommend arranging the units in such a way days a year up to 93 % relative humidity; condenthat they are not exposed to direct sunlight or pronounced sation during operation is not permitted temperature changes that could cause condensation

Functions
Common Definite time-overcurrent protection, directional ANSI 50, 51, 67 Frequency range Setting ranges Overcurrent I>, I>> Time delay T Undervoltage seal-in V< Seal-in time of V< Angle of the directional element (at I>>) Times Pickup time I>, I>> at 2 times of set value at 10 times of set value Drop-off time I>, I>> Drop-off ratio Drop-off ratio V< Tolerances Current pickup (starting) I>, I>> Undervoltage seal-in V< Angle of the directional element Time delays Setting ranges Pickup overcurrent IP Time multiplier IEC-characteristics T Time multiplier ANSI- characteristics D Undervoltage release V< Trip characteristics IEC ANSI Pickup threshold Drop-off threshold Tolerances Pickup threshold IP Pickup threshold V< Time for 2 I/IP 20 11 to 69 Hz 0.05 to 20 A (steps 0.01 A); 5 times at IN= 5 A 0 to 60 s (steps 0.01 s) or indefinite 10 to 125 V (steps 0.1 V) 0.1 to 60 s (steps 0.01 s) 90 to + 90 (steps 1)

approx. 35 ms approx. 25 ms approx. 50 ms I>: 0.95; I>>: 0.9 to 0.99 (steps 0.01) approx. 1.05 1 % of set value or 10/50 mA 1 % of set value or 0.5 V 1 1 % or 10 ms 0.1 to 4 A (steps 0.01 A); 5 times at IN = 5A 0.05 to 3.2 s (steps 0,01 s) or indefinite 0.5 to 15 (steps 0.01) or indefinite 10 to 125 V (steps 0.1 V) Normal inverse; very inverse; extremely inverse Inverse; moderately inverse; very inverse; extremely inverse; definite inverse approx. 1.1 IP approx. 1.05 IP for IP/IN 0.3 1 % of set value or 10/50 mA 1 % of set value or 0.5 V 5 % of nominal value + 1 % current tolerance or 40 ms

Inverse time-overcurrent protection ANSI 51V

28

Siemens SIP 6.2 2001

Stator overload protection, thermal ANSI 49

Setting ranges Factor k according to IEC 60255-8 Time constant Time delay factor at stand still Alarm overtemperature Alarm/Trip Overcurrent alarm stage IAlarm Temperature at IN Scaling temperature of cooling medium Limit current ILimit Reset time at emergency start Drop-off ratio / Trip / Alarrm I/IAlarm Tolerances regarding k x IN regarding trip time

0.5 to 2.5 (steps 0.01) 30 to 32000 s (steps 1 s) 1 to 10 (steps 0.01) 70 to 100 % related to the trip temperature (steps 1 %) 0.1 to 4 A (steps 0.01 A); 5 times at IN = 5 A 40 to 200 C (steps 1 C) or 104 to 392 F (steps 1 F) 40 to 300 C (steps 1 C) or 104 to 572 F (steps 1 F) 0.5 to 8 A (steps 0.01), 5 times at IN = 5 A 20 to 150000 s (steps 1 s) Drop-off with Alarrn approx. 0.99 approx. 0.95 2 % or 10/50 mA; class 2 % according to IEC 60255-8 3 % or 1 s: class 3 % according to IEC 60255-8 for I/(k IN)>1.25 3 to 30 % (steps 1 %) 10 to 100 % (steps 1 %) 0 to 60 s (steps 0.01 s) or indefinite 2 to 40 s (steps 0.1 s) 0 to 50000 s (steps 1 s) approx. 50 ms approx. 50 ms approx. 0.95 Drop-off at fall below of I2 perm. 3 % of set value or 0.3 % negative sequence 1 % or 10 ms 5 % of set point +1 % current tolerance or 600 ms 0.25 to 3.0 (steps 0.01) 50 to 120 (steps 1 ) 0 to 50 s (steps 0.01 s) or indefinite 10 to 125 V (steps 0.1 V) approx. 60 ms approx. 50 ms approx. 0.95 approx. 1.1 3 % of set value 1 electrical 1 % or 0.5 V 1 % or 10 ms - 0.5 to 30 % (steps 0.01 %) 0 to 60 s (steps 0.01 s) or indefinite approx. 360 ms (50 Hz); approx. 300 ms (60 Hz) approx. 360 ms (50 Hz); approx. 300 ms (60 Hz) approx. 0.6 0.25 % SN 3 % set value 1 % or 10 ms

Negative sequence protection ANSI 46

Setting ranges Permissible negative sequence I2 perm. /IN Definite time trip stage I2 >>/IN Time delays TAlarm; TI2>> Negative sequence factor K Cooling down time TCooling Times Pickup time (definite stage) Drop-off time (definite stage) Drop-off ratios I2 perm.; I2 >> Drop-off ratio thermal stage Tolerances Pickup values I2 perm.; I2 >> Time delays Thermal characteristic Time for 2 I2/I2 perm. 20 Setting ranges Conductance thresholds 1/xd characteristic (3 characteristics) Inclination angle 1, 2, 3 Time delay T Undervoltage blocking V< Times Stator criterion 1/xd characteristic; Undervoltage blocking Drop-off ratio Stator criterion 1/xd characteristic; Undervoltage blocking Tolerances Stator criterion 1/xd characteristic Stator criterion Undervoltage blocking Time delays T Setting ranges Reverse power PRev.>/SN Time delays T Times Pickup time Drop-off time Drop-off ratio PRev.> Tolerances Reverse power PRev.> Time delays T

Underexcitation protection ANSI 40

Reverse-power protection ANSI 32

Siemens SIP 6.2 2001

29

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Technical data

Forward-power protection ANSI 32F

Setting ranges Forward power PForw.</SN Forward power PForw.>/SN Time delays T Times Pick-up time (accurate measuring) Pick-up time (fast measuring) Drop-off time (accurate measuring) Drop-off time (fast measuring) Drop-off ratio PForw.< Drop-off ratio PForw.> Tolerances Active power PForw.<, PForw.>

0.5 to 120 % (steps 0.1 %) 1 to 120 % (steps 0.1 % 0 to 60 s (steps 0.01 s) or indefinite approx. 360 ms (50 Hz); approx. 300 ms (60 Hz) approx. 60 ms (50 Hz); approx. 50 ms (60 Hz) approx. 360 ms (50 Hz); approx. 300 ms (60 Hz) approx. 60 ms (50 Hz); approx. 50 ms (60 Hz) 1.1 or 0.5 % of SN approx. 0.9 or 0,5 % of SN 0.25 % SN 3 % of set value at Q < 0.5 SN at accurate measuring 0.5 % SN 3 % of set value at Q < 0.5 SN at fast measuring 1 % or 10 ms 0.1 to 20 A (steps 0.01 A); 5 times at IN = 5A 10 to 125 V (steps 0.1V) 0.05 to 130 (steps 0.01 ) 0.05 to 65 (steps 0.01 ) 0.05 to 65 (steps 0.01 ) 0 to 60 s (steps 0.01 s) or indefinite approx. 40 ms approx. 50 ms approx. 0.95 approx. 1.05 1 % of set value or 10/50 mA 1 % of set value or 0.5 V |Z/Z| 5 % for 30 K 90 1% or 10 ms 10 to 125 V (steps 0.1 V) 0 to 60 s (steps 0.01 s) or indefinite 0.1 to 5 s (steps 0.01 s) approx. 50 ms approx. 50 ms 1.01 or 0.5 V 1 % of set value or 0.5 V 1 % or 10 ms 1 % of measured value of voltage 30 to 170 V (steps 0.1 V) 0 to 60 s (steps 0.01 s) or indefinite approx. 50 ms approx. 50 ms 0.9 to 0.99 (steps 0.01) 1 % of set value 0.5 V 1 % or 10 ms 4 40 to 65 Hz (steps 0.01 Hz) 3 stages 0 to 100 s, 1 stage up to 600 s (steps 0.01 s) 10 to 125 V (steps 0.1 V) approx. 100 ms approx. 100 ms approx. 20 mHz approx. 1.05 10 mHz (at V> 0.5 VN) 1 % of set value or 0.5 V 1 % or 10 ms

Time delays T Impedance protection ANSI 21 Setting ranges Overcurrent pickup I> Undervoltage seal-in V< Impedance Z1 (related to IN =1 A) Impedance Z1B (related to IN =1 A) Impedance Z2 (related to IN =1 A) Time delays T Times Shortest tripping time Drop-off time Drop-off ratio Overcurrent pickup I> Undervoltage seal-in V< Tolerances Overcurrent pickup I> Undervoltage seal-in V< Impedance measuring Z1, Z2 Time delays T Setting range Undervoltage pickup V<, V<<, Vp< (positive sequence as phase-to-phase values) Time delays T Time multiplier TM Times Pickup time V<, V<< Drop-off time V<, V<< Drop-off ratio V<, V<<, Vp< Tolerances Voltage limit values Time delays T Inverse-time characteristic Setting ranges Overvoltage pickup V>, V>> (maximum phase-to-phase voltage or phase-to-earth-voltage) Time delays T Time Pickup times V>, V>> Drop-off times V>, V>> Drop-off ratio V>, V>> Tolerances Voltage limit value Time delays T Setting ranges Steps; selectable f>, f< Pickup values f>, f< Time delays T Undervoltage blocking V1< Times Pickup times f>, f< Drop-off times f>, f< Drop-off difference f Drop-off ratio V1< Tolerances Frequency Undervoltage blocking Time delays T

Undervoltage protection (definite-time and inverse-time function) ANSI 27

Overvoltage protection ANSI 59

Frequency protection ANSI 81

30

Siemens SIP 6.2 2001

Overexcitation protection (Volt/Hertz) ANSI 24

Setting ranges Pickup threshold alarm stage Pickup threshold V/f>>-stage Time delays T Characteristic values of V/f and assigned times t(V/f ) Cooling down time TCooling Times (Alarm and V/f>>-stage) Pickup times at 1.1 of set value Drop-off times Drop-off ratio (alarm, trip) Tolerances V/f-Pickup Time delays T Thermal characteristic (time) Setting ranges Displacement voltage V0 > Earth current 3I0> Angle of direction element Time delays T Times Pickup times V0>, 3I0> Drop-off times V0>/ 3I0> Drop-off ratio V0>, 3I0> Drop-off difference angle Tolerances Displacement voltage Earth current Time delays T Setting ranges Earth current pickup IEE>, IEE>> Time delays T Measuring circuit supervision IEE< Times Pickup times Drop-off times Measuring circuit supervision Drop-off ratio IEE>, IEE>> Drop-off ratio measuring circuit supervision IEE< Tolerances Earth current pickup Time delays T Setting ranges Displacement voltage V0 (3rd harm.)>, V0 (3rd harm.)< Time delay T Active power release Positive sequence voltage release Times Pickup time Drop-off time Drop-off ratio Undervoltage stage V0 (3rd harm.)< Overvoltage stage V0 (3rd harm.)> Active power release Positive sequence voltage release Tolerances Displacement voltage Time delay T Setting ranges Current thresholds I>BF Time delay BF-T Time Pickup time Drop-off time Tolerances Current threshold I>BF/IN Time delay T

1 to 1.2 (steps 0.01) 1 to 1.4 (steps 0.01) 0 to 60 s (steps 0.01 s) or indefinite 1.05/1.1/1.15/1.2/1.25/1.3/1.35/1.4 0 to 20000 s (steps 1s) 0 to 20000 s (steps 1s) approx. 60 ms approx. 60 ms 0.95 3 % of set value 1 % or 10 ms 5 % rated to V/f or 600 ms 2 to 125 V (steps 0.1 V) 2 to 1000 mA (steps 1 mA) 0 to 360 (steps 1 ) 0 to 60 s (steps 0,01 s) or indefinite approx. 50 ms approx. 50 ms 0.7 10 directed to power system 1 % of set value or 0.5 V 1 % of set value or 0.5 mA 1 % or 10 ms 2 to 1000 mA (steps 1 mA) 0 to 60 s (steps 0.01 s) or indefinite 1.5 to 50 mA (steps 0.1 mA) approx. 50 ms approx. 50 ms approx. 2 s 0.95 or 1 mA approx. 1.1 or 1 mA 1 % of set value or 0.5 mA 1 % or 10 ms 0.2 to 40 V (steps 0.1 V) 0 to 60 s (steps 0.01 s) or indefinite 10 to 100 % (steps 1 %) or indefinite 50 to 125 V (steps 0.1 V) or indefinite approx. 80 ms approx. 80 ms approx. 1.4 approx. 0.6 approx. 0.9 approx. 0.95 3 % of set value or 0.1 V 1 % or 10 ms 0.04 to 1 A (steps 0.01 A) 0.06 to 60 s (steps 0.01 s) or indefinite approx. 50 ms approx. 50 ms 1 % of set value or 10/50 mA 1 % or 10 ms

90 % stator earth-fault protection, non-directional, directional ANSI 59N, 64G, 67G

Sensitive earth-fault protection ANSI 50/51GN, 64R

100 % stator earth-fault protection with 3rd harmonic ANSI 59TN, 27TN (3rd H.)

Breaker-failure protection ANSI 50BF

Siemens SIP 6.2 2001

31

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Technical data

Inadvertent energizing protection ANSI 50, 27

Setting ranges Current pickup I>>> Voltage release V1< Time delay Drop-off time Times Reaction time Drop-off time Drop-off ratio I>>> Drop-off ratio V1< Tolerances Current pickup Undervoltage seal-in V1< Time delay T Setting ranges Differential current IDiff>IN High-current stage IDiff>>IN Inrush stabilization ratio I2fN/IN Harmonic stabilization ratio InfN/IN (n=3rd or 4rd or 5rd harmonics) Additional trip time delay T Times Pickup time (IDiff 1.5 setting value IDiff >) Pickup time (IDiff 1.5 setting value IDiff>>) Drop-off time Drop-off ratio Tolerances Pickup characteristic Inrush stabilization Additional time delays

0.1 to 20 A (steps 0.1 A); 5 times at IN= 5 A 10 to 125 V (steps 1 V) 0 to 60 s (steps 0.01 s) or indefinite 0 to 60 s (steps 0.01 s) or indefinite approx. 25 ms approx. 35 ms approx. 0.8 approx. 1.05 5 % of set value or 20/100 mA 1 % of set value or 0.5 V 1 % or 10 ms 0.05 to 2 (steps 0.01) 0.8 to 12 (steps 0.1) 10 to 80 (steps 1 %) 10 to 80 (steps 1 %) 0 to 60 s (steps 0.01 s) or indefinite approx. 35 ms approx. 20 ms approx. 35 ms approx. 0.7 3 % of set value or 0.01 I/IN 3 % of set value or 0.01 I/IN 1% or 10 ms 0.01to 1 (steps 0.01) 0 to 60 s (steps 0.01 s) or indefinite approx. 50 ms approx. 50 ms approx. 0.7 3 %of set value 1 % or 10 ms 3 to 30 k (steps 1 k) 1.0 to 5.0 k (steps 0,1 k) 0 to 60 s (steps 0,01 s) or indefinite - 15 to + 15 (steps 1 ) 80 ms 80 ms approx. 1.25 approx. 5 % of set value approx. 10 % of set value 1% or 10 ms 0.15 to 3 F

Current differential protection ANSI 87G, 87M, 87T

Earth-current differential protection ANSI 87GN, 87TN

Setting ranges Differential current IE-Diff >/IN Additional trip time delay Times Pickup time (IE-Diff 1.5 setting value IE-Diff >) Drop-off time Drop-off ratio Tolerances Pickup characteristic Additional time delay

Rotor earth-fault protection with fN ANSI 64R (fN)

Setting ranges Alarm stage RE, Alarrn < Trip stage RE, Trip < Time delays T Correction angle Times Pickup time Drop-off time Drop-off ratio Tolerances Trip stage RE, Trip <, Alarm stage RE, Alarm < Time delays T Permissible rotor earth capacitance

32

Siemens SIP 6.2 2001

Sensitive rotor fault protection with 1 to 3 Hz ANSI 64R (1 to 3 Hz)

Setting ranges Alarm stage RE,Alarrn < Trip stage RE, Trip < Time delays T Pickup value of meas. circuit supervision QC< Times Pickup time Drop-off time Drop-off ratio RE Drop-off ratio QC < Tolerances Trip stage (RE,Trip <; Alarm stage RE, Alarm<) Time delays T Permissible rotor earth-capacitance

5 to 80 k (steps 1 k) 1 to 10 k (steps 1 k) 0 to 60 s (steps 0.01 s) or indefinite 0.01 to 1 mAs (steps 0.01 mAs) approx. 1 to 1.5 s (depends on frequency of 7XT71) approx. 1 to 1.5 s approx 1.25 1.2 or 0.01 mAs approx. 5 % or 0.5 k at 0.15 F CE < 1F approx. 10 % or 0.5 k at 1 F CE < 3 F 1% or 10 ms 0.15 to 3 F 20 to 500 (steps 1 ) 10 to 300 (steps 1 ) 0.02 to 1.5 A (S steps 0.01 A) 0 to 60 s (steps 0.01 s) or indefinite 0.3 to 15 V (steps 0.1 V) 5 to 40 mA (steps 1 mA) - 60 to + 60 (steps 1 ) 1.3 s 250 ms 0.8 s 120 ms approx. 1.2 to 1.7 ca. 5 % or 2 3 % or 3 mA 1 % or 10 ms 0.2 to 4 I1/IN (steps 0.1 I1/IN ) 0.05 to 1 I2/IN (steps 0.01 I2/IN ) 0.05 to 130 (steps 0.01 ) 60 to 90 (steps 1 ) 1 to 4 1 to 8 0.2 to 60 s (steps 0.01 s) 0.02 to 0.15 s (steps 0.01s) Depending from the out-of-step-frequency |Z/Z| 5 % for 30 SC 90 or 10 m 1 % to 10 ms 0.1 to 8.5 V (steps 0.1 V) 0.2 to 17 mA (steps 0.1 mA) 0 to 60 s (steps 0.01 s) or indefinite approx. 60 ms approx. 200 ms approx. 60 ms or 200 ms 0.9 or 1.1 1 % of set value, or 0.1 V 1 % of set value, or 0.1 mA 1 % or 10 ms

100% stator earth-fault protection with 20 Hz ANSI 64G (100%)

Setting ranges Alarm stage RSEF < Trip stage RSEF << Earth current stage ISEF > Time delays T Supervision of 20 Hz generator V20 Hz I20 Hz Correction angle Times Pickup times RSEF<, RSEF<< Pickup time ISEF> Drop-off times RSEF<, RSEF<< Drop-off time ISEF> Drop-off ratio Tolerances Resistance (RSEF Earth current stage (ISEF >) Time delays T

Out-of-step protection ANSI 78

Setting ranges Positive sequence current pickup I1> Negative sequence current pickup I2< Impedances Za to Zd (based on IN =1 A) Inclination angle of polygon P Number of out-of-step periods characteristic 1 Number of out-of-step periods characteristic 2 Holding time of pickup tH Holding time for out-of-step annuncation Times Typical trip time Tolerances Impedance measurement Time delays T

DC voltage time / DC current time protection ANSI 59N (DC) ; 51N (DC)

Setting ranges Voltage pickup V = >,< Current pickup I = >, < Time delays T Times Pickup time (operational condition 1) Pickup time (operational condition 0) Drop-off time Drop-off ratio Tolerances Voltage Current Time delays T

Siemens SIP 6.2 2001

33

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Technical data

Starting time supervision for motors ANSI 48

Setting ranges Motor starting current IStart max /IN Starting current pickup IStart, pickup. /IN Permissible starting time T Start max Permissible locked rotor time T Blocking Times Drop-off ratio Tolerances Current threshold Time delays T

1.0 to 16.0 (steps 0.01) 0.6 to 10.0 (steps 0.01) 1.0 to 180.0 s (steps 0.1 s) 0.5 to 120.0 s (steps 0.1 s) or indefinite Depending on the settings approx. 0.95 1 % of set value, or 1 % of IN 5 % or 30 ms 3.0 to 10.0 (steps 0.01) 3.0 to 120.0 s (steps 0.1 s) 0 to 60.0 min (steps 0,1 min) 0.2 to 120.0 min (steps 0.1 min) 1 to 4 1 to 2 1.0 to 100.0 1 % or 0.1 ms 4 0.2 to 10 Hz/s (steps 0.1 Hz/s); 0 to 60 s (steps 0.01 s) or indefinite 10 to 125 V (steps 0.1 V) approx. 200 ms approx. 200 ms approx. 0.95 or 0.1 Hz/s approx. 1.05 approx. 0.1 Hz/s at V> 0.5 VN 1 % of set value or 0.5 V 1% or 10 ms 0.5 to 15 (steps 0.1 ) 0 to 60 s (steps 0.01 s) or indefinite 10 to 125 V (steps 0.1 V) 0.3 at V> 0.5 VN 1 % of set value or 0.5 V 1 % or 10 ms 6 or 12 40 to 250 C or 100 to 480 F (steps 1 C or 1 F) T100; Ni 100, Ni 120 4 1

Restart inhibit for motors ANSI 66, 49 Rotor

Setting ranges Motor starting current IStart max /IN Permissible starting time T Start max Rotor temperature equalization time T Equali. Minimum restart inhibit time T Restart, min Permissible number of warm starts nW Difference between warm- and cold starts nK-nW Extensions of time constants (running and stop) Tolerances Time delays T

Rate-of-frequency change protection ANSI 81R

Setting ranges Steps, selectable +df/dt >; - df/dt Pickup value df/dt Time delays T Undervoltage blocking V1< Times Pickup times df/dt Drop-off times df/dt Drop-off ratio df/dt Drop-off ratio V< Tolerances Rate of frequency change Undervoltage blocking Time delays T

Vector jump supervision (voltage)

Setting ranges Stage Time delay T Undervoltage blocking V1< Tolerances Vector jump Undervoltage blocking Time delay T

Incoupling of temperature via serial interface (RTD module) ANSI 38

Number of measuring junctions Temperature thresholds RTD types

External trip coupling Trip circuit supervision ANSI 74TC

Number of external trip couplings Number of supervised trip circuits

34

Siemens SIP 6.2 2001

Operational measured values

Description Currents Tolerance Differential protection currents Tolerances Phase angles of currents Tolerances Voltages Tolerance Impedance Tolerance Power Tolerance Phase angle Tolerance Power factor Tolerance Frequency Tolerance Overexcitation Tolerance Thermal measurement Tolerance Memory Reset manual

Primary; secondary or per unit (%) IL1, S1; IL2, S1; IL3, S1; IL1, S2; IL2, S2; IL3, S2; IEE1; IEE2; I1; I2 0.2 % of measurement values or 10 mA 1 digit IDiffL1; IDiffL2; IDiffL3; IRestL1; IRestL2; IRestL3; 0.1 % of measured or 10 mA 1 digit IL1,S1; IL2,S1; IL3,S1; IL1,S2; IL2,S2; IL3,S2; < 0.5 VL1; VL2; VL3; VE; VL12; VL23; VL31; V1; V2 0.2 % of measured values or 0.2 V 1 digit R, X 1% S; P; Q 1 % of measured values or 0.25 % SN <0.1

cos (p.f.) 1% 1 digit f 10 mHz (at V> 0.5 VN; 40 Hz < f < 65 Hz) V/f;
1% L1; 5%
L2, L3, I2, , V/f

RTDs

Min./max. memory

Measured values with date and time via binary input via key pad via communication

Values Positive sequence voltage Positive sequence current Active power Reactive power Frequency Displacement voltage (3rd harmonics) Energy metering Fault records Meter of 4 quadrants Tolerance Number of fault records Instantaneous values Storage time Sampling interval Channels Rms values Storage period Sampling interval Channels Additional functions Fault event logging

V1 I1 P Q f VE(3rd harm.) WP+; WP; WQ+; WQ 1%


max. 8 fault records max. 5 s depending on the actual frequency (e. g. 1.25 ms at 50 Hz; 1.04 ms at 60 Hz) vL1, vL2, vL3, vE; iL1,S1; iL2,S1; iL3,S1; iEE1; iL1,S2; iL2,S2; iL3,S2; iEE2; TD1; TD2; TD3 max. 80 s fixed (20 ms at 50 Hz; 16.67 ms at 60 Hz) V1, VE, I1, I2, IEE1, IEE2 , P, Q, , R, X, f-fn Storage of events of the last 8 faults Puffer length max. 600 indications Time solution 1 ms max. 200 indications Time solution 1 ms up to 6 decimal digits (criterion: current threshold) Number of breaker operation Phase-summated tripping current This conformity is the result of a test that was performed by Siemens AG in accordance with Article 10 of the directive in conformance with generic standards EN 50081-2 and EN 50082-2 for the EMC directive and EN 60255-6 for the low-voltage directive.

Operational indications Elapsed-hour meter Switching statistics CE conformity The product meets the stipulations of the guideline of the council of the European Communities for harmonization of the legal requirements of the member states on electro-magnetic compatibility (EMC directive 89/336/EEC) and product use within certain voltage limits (low-voltage directive 73,23/EEC). The product conforms with the international standard of the IEC 60255 series and the German national standard DIN VDE 57 435,Part 303. The unit has been developed and manufactured for use in industrial areas in accordance with the EMC standard.

Siemens SIP 6.2 2001

35

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Selection and ordering data

Designation Multifunction generator protection SIPROTEC 4 Housing, binary inputs and binary outputs Housing 1/2 19", 7 BI, 11 BO, 1 live status contact Housing 1/1 19", 15 BI, 20 BO, 1 live status contact Current transformer IN 1 A, IEE (sensitive) 5 A, IEE (sensitive) Auxiliary voltage (power supply, indication voltage) 24 to 48 V DC, threshold binary input 17 V 60 to 125 V DC, threshold binary input 17 V 110 to 250 V DC, 115 V AC, threshold binary input 73 V

Order No.
ss s s s s s s s s

Order Code
sss

7UM62--0
1 2

1 5

2 4 5

Unit version with Surface-mounting housing, 2 tier screw-type terminals top/bottom Flush-mounting housing, plug-in terminals (2-/3 pin AMP-connector) Flush-mounting housing, screw-type terminal (direct connection, ring-type cable lugs) Region-specific default setting/function and language settings Region DE, 50 Hz, IEC characteristics, language: German, (language can be adjusted) Region World, 50/60 Hz, IEC/ANSI characteristics, language: English, (language can be adjusted) Region US, 60 Hz, ANSI characteristics, language: American, (language can be adjusted) Port B (System Interface) No system interface IEC protocol, electric RS232 IEC protocol, electric RS485 IEC protocol, optical 820 nm, ST-connector Analog output 2 x 0 to 20 mA Further protocols Port B PROFIBUS-DP slave, electric RS485 PROFIBUS-DP slave, optical 820 nm, double ring, ST-connector MODBUS, electric RS485 MODBUS, optical 820 nm, ST-connector Only Port C (Service Interface) DIGSI 4 / modem, electric RS232 DIGSI 4 / modem, RTD module, electric RS485 Port C (Service interface) and Port D (Additional Interface) Port C (Service Interface) DIGSI 4 / modem, electric RS232 DIGSI 4 / modem, RTD module, electric RS485 Port D (Additional Interface) RTD module, optical 820 nm, ST connector RTD module, electric RS485 Analog outputs 2 x 0 to 20 mA Measuring functions without extended measuring functions min./max. values, energy metering Functions1) Generator Basic Generator Standard Generator Full Asynchronous Motor Transformer Functions (additional functions)1) without Sensitive rotor earth-fault protection and 100 % stator earth-fault protection Network decoupling (df/dt and vector jump) all additional functions

B D E

A B C

0 1 2 3 7 9 9 9 9 L L L L 0 0 0 0 A B D E

1 2 9

Mo o

1 2

A F K

0 3

A B C F H

A B E G

1) For more detailled information on the functions see Table 1 on page 3.

36

Siemens SIP 6.2 2001

Accessories

LSP2288f.eps

Fig. 32 Fig. 33 Fig. 34 Fig. 35 Fig. 36 Fig. 32

Mounting rail for 19 rack 2-pin connector 3-pin connector Short-circuit link for current contacts Short-circuit link for voltage contacts

LSP2093f.eps

LSP2090f.eps

LSP2091f.eps

LSP2092f.eps

Fig. 33

Fig. 34

Fig. 35

Fig. 36

Description Connector Crimp connector 2-pin 3-pin CI2 0.5 to 1 mm2 CI2 1 to 2.5 mm2 Type III + 0.75 to 1.5 mm2 Crimping tool for Type III + and matching female for CI2 and matching female

Order No. C73334-A1-C35-1 C73334-A1-C36-1 0-827039-1 0-827396-1 0-827040-1 0-827397-1 0-163083-7 0-163084-2 0-539635-1 0-539668-2 0-734372-1 1-734387-1 C73165-A63-D200-1 for current terminals for other terminals large small
Tel.: +49 6103 709-0 Fax: +49 6103 709-223

Size of package 1 1 4000 1 4000 1 4000 1 1 1 1 1 1 1 1

Supplier Siemens Siemens AMP 1) AMP 1) AMP 1) AMP 1) AMP 1) AMP 1) AMP 1) AMP 1)

Fig. 33 34

19"-mounting rail Short-circuit links

Siemens Siemens Siemens Siemens Siemens

32 35 36

C73334-A1-C33-1 C73334-A1-C34-1 C73334-A1-C31-1 C73334-A1-C32-1

Safety cover for terminals


1) AMP Deutschland GmbH Amperestr. 711 63225 Langen Germany

Product description DIGSI 4 Software for configuration and operation of Siemens protection units MS Windows program, running under MS Windows (version MS Windows 95 and higher). Unit templates, COMTRADE Viewer, electronic manual included

Variants Basis Full version with license for 10 computers, on CD-ROM (authorization with license number). Additional: CD-ROM with DIGSI 3 Demo Demo version on CD-ROM Professional Complete version: Basis and all optional packages on CD-ROM Additional: CD-ROM with DIGSI 3 between PC and relay (9-pin female connector to 9-pin male connector)

Order No. 7XS5400-0AA00

7XS5401-0AA00 7XS5402-0AA00

Connecting cable (copper)

7XV5100-4 7XR6100-0CA00 3PP1336-0DZ-013002 3PP1326-0BZ-012009 3PP1336-1CZ-013001 7XT3300-0CA00 7XT3400-0CA00 4NC1225-2CK20


7XT7100-0EA00

Coupling device for rotor earth-fault protection (rated frequency voltage) Series resistor for rotor earth-fault protection (fn) Voltage devider (10:1, 20:1) Voltage devider (5:1, 5:2) 20 Hz generator 20 Hz band pass filter Current transformer (400 A/ 5 A) Controlling unit f. rotor earth-fault protection (1 to 3 Hz) Resistor for 1 to 3 Hz rotor earth-fault protection Temperature monitoring device (RTD module) Instruction manual 7UM62; V4.0 Advertising brochures English 7UM61/62 German 7UM61/62

7XR6004-0CA00 7XV5662-0AD10 C53000-G1176-C149-1 E50001-U321-A149-X-7600 E50001-U321-A149


Siemens SIP 6.2 2001

37

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Connection diagrams acc. to IEC

Fig. 37 Connection diagram

38

Siemens SIP 6.2 2001

Fig. 38 Connection diagram

Siemens SIP 6.2 2001

39

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Connection diagrams acc.to ANSI

Fig. 39 Connection diagram

40

Siemens SIP 6.2 2001

Fig. 40 Connection diagram

Siemens SIP 6.2 2001

41

SIPROTEC 4 - 7UM62 Multifunction Generator, Motor and Transformer Protection Relay


Dimension drawings in mm / in inches

Fig. 41 Side view of flush-mounting housing With screw-type terminals With plug-in terminals

Fig. 42 7UM621 in 1/2 flush-mounting housing 7XP20

Panel cutout

Rear view

Panel cutout

Rear view

Fig. 43 7UM622 in 1/1 flush-mounting housing 7XP20

42

Siemens SIP 6.2 2001

(without sloped FO case) Fig. 44 Front view in 1/2 surface-mounting housing 7XP20 Fig. 45 Side view

Fig. 46 Front view in 1/1 surface-mounting housing 7XP20 (without sloped FO case)

Siemens SIP 6.2 2001

43

Conditions of Sale and Delivery Subject to the General Conditions of Supply and Delivery for Products and Services of the Electrical and Electronic Industry and to any other conditions agreed upon with the recipients of catalogs. n The technical data, dimensions and weights are subject to change unless otherwise stated on the individual pages of this catalog. The illustrations are for reference only. We reserve the right to adjust the prices and shall charge the price applying on the date of delivery

Export Regulations In accordance with present provisions of the German Export List and the US Commercial Control List, export licences are not required for the products listed in this catalog. An export licence may however be required due to country-specific application and final destination of the products. Relevant are the export criteria stated in the delivery note and the invoice regarding a possible export and reexport licence. Subject to change without notice.

Trademarks All product designations used are trademarks or product names of Siemens AG or of other suppliers.

Dimensions All dimensions in this catalog are given in mm.

Responsible for Technical contents: Dr. Hans-Joachim Herrmann Siemens AG, PTD PA 13, Nuernberg General editing: Claudia Khn-Sutiono Siemens AG, PTD CC T, Erlangen

44

Siemens SIP 6.2 2001

Order No.: E50001-K4406-A121-A1-7600 Printed in Germany KGK 0701 5.0 44 En 101753 6101/D6111

Published by Siemens Aktiengesellschaft Power Transmission and Distribution Power Automation Division Postfach 48 06 90026 Nuernberg Germany www.ptd.siemens.de
Order No.: E50001-K4406-A121-A1-7600

You might also like