14) Stress Breaker - Stress Equalizer

Stress breaker –Stress
equalizer
BUSHRA MOHAMMED ALI AL - AMEEN
B,D,S ,. M,SC.(PROS )
STRESS BREAKER
In the distal extension RPD, Support is derived from both
the residual ridge and abutment teeth.
The variation in consistency providing this support allows
some rotational movements of the free end base towards the
soft tissues.
Harmful tissue –ward movements of distal extension under
occlusal load are transmitted to the abutment teeth resulting
in loosening of these teeth.
Dentures with a stress breaker are also called as a broken
stress partial dentures or articulated prostheses
STRESS BREAKER
STRESS BREAKER :
 It is A device which relieves the abutment teeth of all or part of the occlusal forces” Or, "is a device that
allows movement between the denture base and the direct retainer which may be intracoronal or
extracoronal”.
Or, It is a device that permits some hinge or rotational movement between the denture base or its
supporting framework and the direct retainers (whether they are intra coronal or extracoronal retainer),
this device separate the action of the direct retainers from the base movement, so it was used to
minimize strain on the abutment teeth to which the partial denture is attached and transfer them to the
denture bearing areas. It is indicated in a distal extension restoration.
All vertical and horizontal forces applied to the artificial teeth are distributed throughout the supporting
portions of the dental arch. Broad distribution of the force is obtained through the rigid major, minor
connectors and stabilizing components.
Types of stress breaker
1-First group (non rigid attachments): RPD
having a movable joint between the direct retainer and
the denture base. include hinge , sleeve and cylinder,
ball and socket device.
These types have a movable joint between the direct
retainer and the denture base and permit vertical
movement and hinge action of the distal extension
denture base.
2-second group: include design having a
flexible connection between the direct
retainer and the denture base (articulated partial
denture) this group include the use of:
A-Divided major connector (split bar):
by using this type of stress breakers, the vertical forces
applied on distal extension base must pass anteriorly
along the lower bar and then back along more rigid
upper bar to reach abutment tooth therefore the
tipping forces that would otherwise be transmitted
directly to abutment teeth are dissipated by flexibility of
lower bar and distance traveled .
2-second group: include design having a flexible
connection between the direct retainer and the denture
base (articulated partial denture) this group include the
use of:
B-Wrought wire clasp (combination clasp)
C-clasps having stress breaking effect:
1-RPI system
2-Reverse Aker clasp
3-RPA system
R=rest mesially located, P=proximal plate, A= Aker
clasp
use of:
1-RPI system
3-RPA system
clasp
use of:
1-RPI system
3-RPA system
clasp
use of:
1-RPI system
3-RPA system
clasp
Advantages Of Stress Breakers:
1. Preservation of alveolar support of abutment teeth by minimizing the horizontal forces acting
on the teeth.
2. The flexible type of stress breaker creates a balance of stress between the abutment teeth and the
residual ridge
3. Movement of the denture base result in the physiologic stimulation to the mucosa
4. If relining is needed and but not done, the abutment teeth are not damaged quickly.
5. The flexible attachment (non-rigid attachment) of the distal extension base to the major
connector makes splinting of weak teeth by the denture framework is possible.
Disadvantages Of Stress Breakers:
1. Lack of occlusal stability.
2. Not provide bracing for lateral forces
3. Improper control of forces distribution between the dentate and edentulous areas.
4. The denture is more difficult to fabricate and therefore more costly.
5. If relining is not done when needed excessive resorption of the residual ridge may result
6. Flexible connectors may be bent and fractured by careless handling and by repeated flexing.
7. Repair and maintenance of any stress breaker are difficult, costly, and frequently required.
8. All mechanical devices those are free to move in the mouth in collect debris and become unclean.
9. some split connector is used as stress breaker pinch the underlying soft tissue or the tongue as they
open and close under function.

14) Stress Breaker - Stress Equalizer

Uploaded by

Copyright:

Available Formats

14) Stress Breaker - Stress Equalizer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

14) Stress Breaker - Stress Equalizer

Uploaded by

Copyright:

Available Formats

What is a stress breaker?

What are the types of stress breakers?

Stress breaker –Stress

You might also like