Engine BWA - 2.0 FSI Timing Belt Installation - Not OEM
Engine BWA - 2.0 FSI Timing Belt Installation - Not OEM
Engine BWA - 2.0 FSI Timing Belt Installation - Not OEM
0T Timing Belt
FSI Installation
This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat® Reader®
Proper service and repair procedures are vital to the safe, reliable operation of all engine vehicles as well as the personal safety of those per-
forming the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be
followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safe-
ty.
Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its ac-
curacy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRAN-
TY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS
MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory,
arising out of the use of this material.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Getting Ready
Battery Disconnects and Keep Alive Memory
Most instruction sheets begin with a recommendation to disconnect the battery. This general caution is included because cranking
the engine over with the timing belt removed results in immediate and costly damage to an interference engine. (Those wishing to
forego this step should at least remove the keys from the ignition and hide them until the job is complete.)
Caution: Disconnecting the battery commonly erases volatile memory in the powertrain controller and any other control module.
If you want to keep these data in memory (emissions-related OBD information, radio presets, etc.), a “memory saver” can be
connected that supplies low current voltage to keep alive memory. Good backup power supplies do not have enough wattage to
operate the starter and include feedback circuit protection.
The ECS Tuning Ultimate Plus Timing Belt Kit for the VW 2.0T
FSI contains belts, bolts, seals, rollers, tensioner, and coolant.
To find the correct kit for your vehicle, first select your
vehicle at ecstuning.com, then click:
Engine > Timing > Timing Belt Kit
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 2
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
You’ll need some way to support the engine while the right side engine mount is removed, and some way to raise and lower it slightly to
make wiggle room at different stages of the procedure. If you use a hydraulic floor jack instead of a hanger, locate it under the engine in a
spot where it cannot slip.
We’ll use an engine support bar that straddles the engine compartment. Its threaded rods and attachment chains let you safely raise
and lower either side of the powertrain from above. This tool is also useful for other procedures, including transmission repair and clutch
replacement.
ES2804773
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 3
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
accessory belt
clockwise to
routing loosen tensioner
Reference Pages
The next three pages have illustrated views of belt accesory belt
routings, component and fastener locations, and tensioner alternator
tightening torques.
crank pulley
ac
compressor
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 4
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Fasteners and Component Locations
Your Ultimate Plus timing belt kit comes with new bolts, as required. TTY 10Nm (7.5 ft-lb)
(torque-to-yield bolts) should be replaced when specified by the manufacturer.
TTY bolts (also called “stretch bolts”) are tightened to an initial torque, plus
an additional fraction of a turn, measured in degrees. (example: 60Nm+90
degrees).
16mm top timing cover
OT
40Nm (30ft-lb) 60Nm (45 ft-lb)
+90º camshaft
+90º
bracket engine
chassis to engine mount
mount mount
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 5
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Belt Tensioning
OT
When installing the belt on the cam, crank, and water pump
sprockets, make sure all of the belt slack is on the tensioner
side. The belt should be pulled tight between the cam and
crank on the water pump side. That way, belt timing will idler
not change when the tensioner removes belt slack. camshaft roller
25Nm (18 ft-lb)
Install the tensioner nut on the pivot stud, snug but
not tight. Insert an 8mm hex into the roller, and
rotate it clockwise until the tab is centered in the
notch (see image below). tensioner water
Hold the tensioner in this position as you pump
torque the tensioner roller nut. 15Nm (11 ft-lb)
Bar the engine over clockwise, two
complete revolutions until the
timing marks align again.
idler
8mm roller
Double check both the 35Nm (26 ft-lb)
belt timing and the
tensioner tab alignment.
If the timing marks and TDC
the tensioner are aligned
properly, the belt is ready
to go.
20Nm+90º
(15 ft-lb +90º)
tensioner align tab in notch
roller nut
25Nm (18 ft-lb)
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 6
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 1
Raise the hood.
Step 2
Pop the two spring clips holding the air duct to the rear of the
engine cover/filter housing, and disconnect the duct.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 7
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 3
Loosen the spring clamp (arrow) and disconnect the inlet air duct
from the engine cover/filter housing.
Step 4
Lift straight up to remove the engine cover/filter housing from its
four rubber grommet mounts.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 8
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 5
Disconnect the fuel and fuel vapor rubber hoses from the metal
fuel tubes that run parallel to the front edge of the valve cover.
Step 6
Unplug the electrical connector for the coolant level sensor (1) and
remove the upper hose from the coolant bottle (2).
Remove the small 6mm bolt (10mm head) from the windshield
washer fluid fill neck (3), and pull the neck forward slightly.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 9
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 7
Remove the two screws holding the coolant bottle in place and pull
it forward. Drape it over the front of the car, out of your way. No
need to disconnect the lower coolant hose from the bottle.
Step 8
Remove the two bolts (arrows) and remove the support bracket
next to the engine mount, behind the washer fluid fill neck.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 10
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 9
Loosen the spring-style hose clamp and disconnect the coolant
hose that runs across the front of the timing belt cover.
Pull the hose back out of the way to expose the face of the timing
cover.
Step 10
Raise the car.
Remove the screws and the inner side cover splash shield to expose
the crank pulley.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 11
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 11
There is no cooling system drain plug.
Step 12
There are three bolts securing the right side engine mount to the
block. This is a good time to remove the bottom engine mount bolt
while it is easily accessible.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 12
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 13
Remove the two front bolts from the dogbone mount at the
transaxle. (This will make it easier to jack up the right side of the
engine when we remove the right side engine mount.
Step 14
Return to the engine compartment.
Note: See page 4 of this pdf for a side view illustration of the
tensioner and accessory belt routing.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 13
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 15
Support the engine. We are using an engine hanger that straddles the
engine bay and supports the engine weight from above. (See page 3
for more about the engine hanger.) If you are using a hydraulic jack,
please make sure the engine is securely supported before removing
the engine mount bolts.
Step 16
Lift and remove the top section of the engine mount.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 14
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 17
Jack up the right side of the engine far enough to remove the two
remaining bolts that attach the lower engine mount to the engine
block.
Step 18
Remove the mount. Slide it out far enough to clear the timing cover
before lifting it up and out.
Service Tip: You may need to raise the engine even farther to remove
the mount. It is a tight fit.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 15
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 19
Remove the timing cover screws and lift the cover off. See the
diagram on page 5 of this pdf for exact timing cover bolt locations.
Step 20
Using a 19mm 12-point socket, extension, and long-handled ½ -inch
ratchet, bar the engine over in a clockwise direction until the crank
and camshaft timing marks are aligned as shown here.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 16
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 21
Remove the six hex head bolts holding the crank pulley to the
crankshaft snout.
Service tip: Double check the crank timing marks on the pulley and
lower cover to be sure you did not move the crank when removing
the bolts.
Step 22
Since we just double checked crankshaft timing in the previous
step, we immediately add match marks indicating TDC using an
automotive paint touch up stick. These marks–one on the engine and
one on a sprocket tooth–will alert us immediately if the crank gets
bumped out of position for any reason as we install the new timing
belt.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 17
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 23
Loosen the lock nut on the trensioner (arrow). Using an 8mm hex key,
rotate the tensioner counterclockwise to slacken the timing belt.
Step 24
When installing the new tensioner, insert the L-shaped bracket on the
back of the tensioner into the recessed sealing (freeze) plug on the
engine block (top arrow).
Then install the flat washer and nut just tight enough that you can still
rotate the center of the tensioner with an 8mm hex key (lower arrow).
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 18
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 25
Unbolt and remove the old water pump. You may need to pry back
and forth and wiggle the old pump from its bore. It seals to the block
with an o-ring instead of a gasket, and the old o-ring rubber can
harden in place.
Step 26
When the old pump is removed, clean the pump bore in the block.
Use emery cloth to polish away minor imperfections, rust, or scale
from the bore that might damage the new pump o-ring.
Lube the new o-ring with fresh coolant. Slide it into the block and
torque the fasteners to spec.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 19
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 27
Install the two new idler rollers and torque them to spec. They are
not identical. See page 6 of this pdf for an overview of all component
locations and tightening specs.
With the tensioner roller in the slack position, route the new timing
belt around the sprockets at the cam, crank and water pump, as
shown on page 6.
This photo shows our new timing belt being installed onto the
camshaft sprocket.
Step 28
With the belt routed, use an 8mm hex key to rotate the tensioner
before tightening the lock nut to hold it in place.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 20
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 29
With the belt installed and timed, it’s time to reverse our steps and
reassemble the engine and mounts. Slide the timing cover back in
place and bolt it down.
Reinstall the side mount using the new bolts in your kit.
Step 30
Install fresh bolts at the crankshaft pulley. Use the correct torque-to-
yield specifications to tighten them.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 21
ECS Ultimate Plus Timing Belt Kit Timing Belt Installation
VW 2.0T FSI
Step 31
When everything is reassembled, fill the coolant jug to the max mark
with a mix of antifreeze/coolant and distilled or demineralized water
that bring the final mix ratio to 50:50.
Start the engine and turn the heater to max hot. Run the engine at
an elevated rpm (1200-1500 rpm) for about two minutes or until the
heater blows hot while monitoring the temp gauge.
Install the cooling system pressure cap and let the engine run until
the cooling fan cycles. The coolant level should be at the max level at
normal engine temperature.
Address: 1000 Seville Road, Wadsworth, OH 44281 Phone: 1.800.924.5172 Web: www.ecstuning.com 22