Apr.

2000 VG-88

SPECIFICATIONS

VG-88 : V-Guitar System

• AD Conversion • Connectors
V-Guitar System A/D GK IN
24 bit AF Method (NORMAL GUITAR INPUT
INPUT) GUITAR OUTPUT
20 bit (GK INPUT) OUTPUT L(MONO)
Table of Contents OUTPUT R
• D/A Conversion PHONES
SPECIFICATIONS .............................................................. ...................................................................................... 1
20 bit 128 times SUB EXP PEDAL/SUB
LOCATION OF CONTROLS .............................................. ...................................................................................... 2 Oversampling ∆Σ Modulation CTL1,2
LOCATION OF CONTROLS PARTS LIST ......................... ...................................................................................... 2 MIDI IN
EXPLODED VIEW .............................................................. ...................................................................................... 3 • Sampling Frequency MIDI OUT
EXPLODED VIEW PARTS LIST ........................................ ...................................................................................... 4 44.1kHz
WIRING DIAGRAM............................................................. ...................................................................................... 4 • Power Supply
PARTS LIST ....................................................................... ...................................................................................... 5 • Program Memories AC 117V,230V,240V
260(PRESET: 160 +
IDENTIFYING THE VERSION NUMBER ........................... ...................................................................................... 7
USER:100) • Power Comsumption
USER DATA SAVE AND LOAD ......................................... ...................................................................................... 8 24W
FACTORY PRESET ........................................................... ...................................................................................... 8 • Nominal Output Level
HOW TO VERSION UP THE FLASH ROM........................ ...................................................................................... 9 INPUT: -10dBm • Dimensions
TEST MODE ....................................................................... .................................................................................... 10 504(W) x 303(D) x 101(H) mm
BLOCK DIAGRAM .............................................................. .................................................................................... 15 • Input Impedance 19-7/8(W) x 11-15/16(D) x
INPUT:1M Ω 4(H) inches
CIRCUIT BOARD (MAIN BAORD ASSY)........................... .................................................................................... 16
CIRCUIT DIAGRAM (MAIN-1) ............................................ .................................................................................... 17 • Nominal Output Level • Weight
CIRCUIT DIAGRAM (MAIN-2) ............................................ .................................................................................... 18 OUTPUT:+4dBm 4.9 kg / 10 lbs 13 oz
CIRCUIT DIAGRAM (MAIN-3) ............................................ .................................................................................... 19 GUITAR OUT:-10dBm
CIRCUIT BOARD (PWB SW SHEET) ................................ .................................................................................... 20 • Accessories
CIRCUIT DIAGRAM (SW-1) ............................................... .................................................................................... 21 • Output Impedance Owner's Manual:
CIRCUIT DIAGRAM (SW-2) ............................................... .................................................................................... 22 OUTPUT:2K Ω English(71567667)
GUITAR OUT 2K Ω Japanese(71565301)
ERROR MESSAGES.......................................................... .................................................................................... 23
Quick Start
• Dynamic Range GK Connecting Cable:
100 dB C13-A(5m) (00349067)

• Display
160 x 64 dots backlit LCD • Options
8-segmenat 2-character LED Divided Pickup:GK-2A
Unit Selector:US-20
GK Connecting Cable:C-
• Control 13B(10m)
Output Level knob Expression Pedal:EV-5,FV-
Value dial 300L+PCS-33(Roland)
Output Select button Foot Switch:FS-5U,FS-5L
Function buttons 1-6 (0dBm=0.775 Vrms)
Page > button
Page < button
Exit button
Write button ∗ In the interest of product
Cursor button improvement, the
COSM Guitar button specifications and /or
COSM Amp button appearance of this unit are
Effects button subjct to change without
Level/BPM/Key button prior notice.
Pedal/Assign button
Name/Chain button
EZ Edit button
Tuner button
Number pedals 1-4
CTL pedal
Bank Up pedal
Bank Down pedal
Expression pedal
Pedal Number LEDs 1-4
Control Pedal LED
Output Select LEDs x 3

Copyright 2000 ROLAND CORPORATION

Power switch

All rights reserved. No part of this publication may be reproduced in any form without the written permisson of
ROLAND CORPORATION.

17059020 Printed in Japan (AA00) (HK) 1

VG-88 Apr. 2000

LOCATION OF CONTROLS LOCATION OF CONTROLS PARTS LIST

[Parts List of Front Panel view]
NO. Part Code Part Name Description
1 02123656 TOP COVER
2 02123689 DISPLAY COVER
3 01895790 LCD DMF-51026NY-LY
4 00342445 LED SL-1264H
5 01011656 LED (RED) SLR-332VR3F
6 02123690 KEYTOP UNIT
7 01780101 TACT SWITCH SKQKAB
8 00341134 M R-KNOB LF BLK/BLU
10 8 24 9 01016145 14M/M ROTARY POTENTIOMETER RK14K12D0 10KBX2
1 2 3 4 11 9 5 17 18 25 10 22485303 D R-KNOB L BLK 248-303
11 01013223 ROTARY ENCODER EVQ VEM F01 24B
12 02122645 PEDAL LABEL (1)
13 02122656 PEDAL LABEL (2)
14 02122667 PEDAL LABEL (3)
15 02122678 PEDAL LABEL (4)
16 02122689 PEDAL LABEL (CTL)
17 00568945 PEDAL LABEL(BANK DOWN)
18 00568956 PEDAL LABEL(BANK UP)
19 22220321 ESCUTCHEON 222-321
20 22350171 RUBBER FOOT 235-171
21 22180605 SWITCH PEDAL
22 22170103 SUPPORT SPRING (FOR SWITCH PEDAL)
23 13129778 TACT SWITCH SKQKAH
7 24 00787756 PEDAL FV.EV-A
25 00780934 ROLAND RUBBER PLATE
6 [Parts List of Rear Panel view]
26 02123667 BOTTOM COVER
27 13449150 6.5MM JACK HLJ0544-01-010
28 13449155 6.5MM JACK HLJ0544-01-110
5 29 02122390 DIN EXP CONNECTOR TCS5095-114152
30 13429825 MIDI CONNECTOR YKF51-5054 2PZ
31 71569134 AC SW ASSY SDDJE1-A-2 10A/250VAC
32 71565334 AC CORD ASSY 100V
71567690 AC CORD ASSY 117V
71567789 AC CORD ASSY 230V
71567834 AC CORD ASSY 230VE
71567889 AC CORD ASSY 240VA

20 21 22 23

19

12 13 14 15 16

26 29 28 27 30 31

2
Apr. 2000 VG-88

EXPLODED VIEW

m 24 22
23
j e b
9 1 20
o
18
g 19
13 r a
16 m
b
14 q h
11

20 d
12
15 21
17

6
27
10
3 26 44 41
5 7
l
42
8
s
36
q
r 43
k l f 28
4 p
i

32
n
40
n 38
2
30
c
35

29
n 39 34 33
25
n
31

l
m

k 37
37
n m m

3
VG-88 Apr. 2000

EXPLODED VIEW PARTS LIST WIRING DIAGRAM

[Parts List]

EXP VR BOARD ASSY

NO. Part Code Part Name Description Q'TY
1 02123656 TOP COVER 1
2 02123690 KEYTOP UNIT 1
3 02123689 DISPLAY COVER 1
4 00341134 M R-KNOB LF BLK/BLU 1

71565256
5 22485303 D R-KNOB L BLK 248-303 1
6 02122656 PEDAL LABEL (2) 1
7 02122678 PEDAL LABEL (4) 1
CN4
8 02122689 PEDAL LABEL (CTL) 1
9 02122645 PEDAL LABEL (1) 1
10 02122667 PEDAL LABEL (3) 1

WIRING
EXP VR
11 00568945 PEDAL LABEL(BANK DOWN) 1
12 00568956 PEDAL LABEL(BANK UP) 1
13 22220321 ESCUTCHEON 222-321 7
14 22350171 RUBBER FOOT 235-171 7
15 22170103 SUPPORT SPRING (FOR SWITCH PEDAL) 7
16 22180605 SWITCH PEDAL 7
17 01016267 SHAFT STAY 1
18 01120978 CUSHION 30X10X2 1
19 01016223 FOOT 30X10X3 1
20 00787767 BOLT HOLDER FV-A 2 CN1
21 01016212 PEDAL HOLDER 1
22 00787756 PEDAL FV.EV-A 1
23 00780934 ROLAND RUBBER PLATE 1

MAIN BOARD ASSY

24 22140315 HOLDER PIN PIN 214-315(FOR FV/EV) 1
25 71674756 7SEG PANEL SW ASSY 1
26 71674745 NUMBER BANK ASSY 1

CN3

CN2
27 71565256 EXP VR BOARD ASSY 1
28 71565267 PS BOARD ASSY 1

71563501
29 71563501 MAIN BOARD ASSY (EXG) 1
12569249 LITHIUM BATTERY CR2032 220MAH/3V 1

NUMBER BANK ASSY

30 CN8
31 02123589 FUJI CARD 24X180-A5.0BB-P1.25-HBL8 1
32 02123590 BAN CARD BNCD-P=1.25-K-14-100 1
33 02123667 BOTTOM COVER 1

71674745
34 40122645 NITTO FILAMENT TAPE #3883 W19MM (4cm) 4cm
35 02123678 INSULATING SHEET 2
36 40017356 COATING CLIP CS-4 1
37 22355334 FOOT MKS 235-334 6
38 71569134 AC SW ASSY 1

FUJI CARD 24X180-A5.0BB-P1. 25-HBL8

39 01895790 LCD DMF-51026NY-LY 1
40 71565334 AC CORD ASSY 100V 1

WIRING OUTPUT VR
71567690 AC CORD ASSY 117V 1 BNCD-P1. 25-K-14-100

CN5
02123590 CN5
71567789 AC CORD ASSY 230V 1
71567834 AC CORD ASSY 230VE 1

CN1
71567889 AC CORD ASSY 240VA 1
41 02121189 PWR TRANS 100/120V 1
02121190 PWR TRANS 230/240V 1
42 00019567 LINE FILTER FERRITE CORE SFC-6 SFC-6 1

02123589
43 40122556 DOUBLE FACED ADHESHIVE TAPE #575X W30MM 30M 10P 30CM 2cm

CN6
44 40126812 CAUTION LABEL BARRIER(117V ONLY) 1 CN4

CN6 CN7
[Screw]
NO. Part Code Part Name Description Q'TY
A 40015901 E-RING M2.5 SUS 1
40016067 PLAIN WASHER 6X13X1 BZC 2

WIRING LCD
B
C 40011856 INSULATING WASHER 3X8X0.8 FIBER-W 1
D 40011923 WASHER M9.1X13 INTERNAL TOOTH 1
E 40016001 LOCK NUT M6 U BZC 1
F 40011745 HEX NUT M4 SPRING NUT FE ZC 3 CN7
G 40123545 JACK NUT 9X11X2 HLJ0999-01-240 FE NI 6
40015989 HEX BOLT 6X67 HALF THREAD BZC 1

RIBON CABLE
H
I 40013001 SCREW 4X8 PAN W SEMS BZC 4

5X40-P2.0
WIRING PS
J 40019123 SCREW 3X8 BINDING TAPTITE S BZC 14
K 40015945 SCREW 3X8 BINDING TAPTITE S FE ZC 5

7SEG PANEL SW ASSY

CN10
L 40012512 SCREW 3X6 BINDING TAPTITE S ZC 9
M 40342578 SCREW 3X6 TAPTITE S BINDING BZC 19 CN8
N 40011278 SCREW 3X8 BINDING TAPTITE-P FE ZC 20

PS BOARD ASSY
O 40011312 SCREW 3X8 BINDING TAPTITE P FE BZC 2

LCD UNIT
40010245 SCREW 3X6 BINDING BZC 2

71674756
P
71565267
Q 40123545 JACK NUT 9X11X2 HLJ0999-01-240 FE NI 2
R 40016467 JACK WASHER M9.2X14X0.5 FENI 7
S 40235189 RING SE-9 1

4
Apr. 2000 VG-88

PARTS LIST #
PCB ASSY
71674756 7SEG PANEL SW ASSY
Q't
1
NOTE: '7SEG PANEL SW ASSY' includes the following parts.

SAFETY PRECAUTIONS: The parts marked CONSIDERATIONS ON PARTS ORDERING 7SEG PANELSW ASSY on 7SEG
The parts marked have # are new (initial When ordering any parts listed in the parts list, please specify the following items in the NUMBER BANK ASSY on NUM 23503688 RIBBON CABLE 5X40-P2.0 CN7 on 7SEG to CN8 on 7SEG 1
safety-related characteristics.
Use only listed parts oor
parts). *2 order sheet.
QTY PART NUMBER DESCRIPTION MODEL NUMBER
EXP VR BOARD ASSY
PS BOARD ASSY
on EXP
on PS
# ∗∗∗∗∗∗∗∗ PANEL SW ASSY Assy(Unit) 1
replacement. Ex. 10 22575241 Sharp key C-20/50 MAIN BOARD ASSY on # 02122745 WIRING OUTPUT VR CN6 on 7SEG to CN8 on Main 1
15 2247017300 Knob (orange) DAC-15D 40013367 SPACER PLASTIC PIPE 3.2X5X13 on 7SEG 3
Failure to completely fill the above items with correct number and description will result in
delayed or even undelivered replacement.
# 71674745 NUMBER BANK ASSY 1
NOTE: 'NUMBER BANK ASSY' includes the following parts.

40013334 SPACER PLASTIC PIPE 3.2X5X10 CLARYTY on NUM 5

# ∗∗∗∗∗∗∗∗ BANK SW ASSY Assy(Unit) 1
01568512 RIBBON CABLE 3X70-P2.0 CN2 on NUM to CN3 on NUM 1

# 71565256 EXP VR BOARD ASSY 1

CASING Q'ty
NOTE: 'EXP VR BOARD ASSY' includes the following parts.
# 02123667 BOTTOM COVER 1
# 02123689 DISPLAY COVER 1 # 02122801 WIRING EXP VR CN4 on EXP to CN1 on Main 1
# 02123656 TOP COVER 1
00787756 PEDAL FV.EV-A 1 # E 71563501 MAIN BOARD ASSY (EXG) 1
00780934 ROLAND RUBBER PLATE 1 NOTE: 'MAIN BOARD ASSY' includes the following parts.
22220321 ESCUTCHEON 222-321 7
22180605 SWITCH PEDAL 7 # 02122412 WIRING LCD CN7 on Main to LCD 1
22355334 FOOT MKS 235-334 4 01016467 RIBBON CABLE 2X90-P2.0 CN10 on Main to CN11 on Main, 2
CHASSIS Q't CN12 on Main to CN13 on Main
# 02231990 MAIN SHIELD on Main 1
00787767 BOLT HOLDER FV-A 2
# 02231989 JACK SHIELD on Main 1
01016212 PEDAL HOLDER 1
# 02122401 JACK HOLDER 13P on Main 1
KNOB, BUTTON Q't
IC Q't
# 02123690 KEYTOP UNIT 1
00565123 M66310P IC (LED DRIVER) IC2 on 7SEG 1
00341134 M R-KNOB LF BLK/BLU 1
01016434 M66312P IC (LED DRIVER) IC1 on 7SEG 1
22485303 D R-KNOB L BLK 248-303 1
! # 02123612 UPC2933HF IC (REGULATOR) IC3 on PS 1
SWITCH Q't ! 15199294 AN7705F IC (+5V VRGL) IC5 on PS 1
! # 71569134 AC SW ASSY 1 ! 15199230 PQ05RF21 IC (V.RGL) IC5 on PS 1
01780101 SKQKAB TACT SWITCH SW8-SW30 on 7SEG 23 # 02120867 CPU UPD703100(BP106) IC (16BIT CPU) IC1 on Main 1
13129778 SKQKAH TACT SWITCH on NUM SW1-SW7 5 +2 00892556 TC170C140AF-003 (ESP2) IC (CUSTOM) IC12,IC13 on Main 2
# 01908412 LC22039CT-SA6 IC (I/F) IC11 on Main 1
JACK, EXP TERMINAL Q't 01560289 TC55257DFL-55L(EL) IC (SRAM) IC36 on Main 1
13429825 YKF51-5054 2PZ MIDI CONNECTOR JK2 on Main 1 01902212 UPD431000AGW-70LL-E2 IC (SRAM) IC2,IC4 on Main 2
# 02122390 TCS5095-114152 DIN EXP CONNECTOR CN9 on Main 1 01906712 LC324260AJ-60-TLM IC (DRAM) IC15,IC16 on Main 2
13449150 HLJ0544-01-010 6.5MM JACK JK1,JK4 on Main 2 01898701 E28F800B5B70 IC (FLASH MEMORY) IC5 on Main 1
13449155 HLJ0544-01-110 6.5MM JACK JK3,JK5-JK7 on Main 4 01780112 AK4522VF IC (AD/DA) IC23,IC30-IC32 on Main 4
15259110 TC4066BF(TP2) IC(C MOS) IC24-IC26 on Main 3
DISPLAY UNIT Q't
00232645 TC7W14F(TE12L) IC (CMOS) IC37 on Main 1
01895790 DMF-51026NY-LY LCD 1
15259704T0 TC74HC04AF(TP2) IC (HS-CMOS) IC7 on Main 1
NOTE: Replacement DMF-51026NY-LY should be made on a unit base.
# 02232834 TC7SH04F(TE85L) IC (CMOS) IC6 on Main 1
00897912 TC7SH32F(TE85L) IC (2 INPUT OR GATE) IC8 on Main 1
00458034 TC75S51F TE85R IC (OP AMP) IC3 on Main 1
00342445 SL-1264H LED LED9 on 7SEG 1
15289154 UPC4072G2-E1 IC (JFET OP) IC18 on Main 1
NOTE: Replacement SL-1264H should be made on a unit base.
00346445 NJM2100M(TE3) IC (BIPOLAR OP AMP) IC22,IC27-IC29 on Main 4
15289109 M5216FP-600D IC (BIPOLAR OP AMP) IC19 on Main 1
POWER SUPPLY UNIT Q't 15289105 UPC4570G2-E2 IC (BIPOLAR OP AMP) IC17,IC20,IC21 on Main 3
# 02122423 AN78L07M-E1 IC (REGULATOR) IC33 on Main 1
# 71565267 PS BOARD ASSY 1
# 02124634 AN79L07M-E1 IC (REGULATOR) IC34 on Main 1
NOTE: '' includes the following parts.
15199944 SED1335F0B IC (DRIVER) IC35 on Main 1
15289123 M51953AFP-600C IC (RESET) IC10 on Main 1
! # 02122778 HEATSINK on PS 1
15289125 PC-410KT 178FAY IC (PHOTO COUPLER) IC9 on Main 1
! # 02122789 WIRING WIRING PS CN10 on PS to CN6 on Main 1
! # 02232012 SUB HEATSINK on PS 1
40011278 SCREW 3X8 BINDING TAPTITE-P FE ZC on PS 4
40011289 SCREW M3X10 BINDING P-TIGHT FE ZC on PS 1
40016590 NYLON RIVET NRP-345 BLACK on PS 2
# 40345334 HEAT-RESISTANT GLASS TUBE ESG-2 2.5FAY 1M on PS 1(5mm X 2)

5
VG-88 Apr. 2000

TRANSISTOR Q't POTENTIOMETER Q't

! 15119132 2SA1015-GR(TPE2) TRANSISTOR Q4 on PS 1 01016145 RK14K12D0 10KBX2 14M/M ROTARY POTENTIOMETER VR2 on 7SEG 1
! 15119823 2SB1375 POWER TRANSISTOR Q2 on PS 1 01016167 RK11K1140(10K SP B) 10KX1 11M/M ROTARY POTENTIOMETER VR1 on EXP 1
! 01019412 2SC2120Y TRANSISTOR Q3 on PS 1
CAPACITOR Q't
! 15129844 2SD2012 TRANSISTOR Q1 on PS 1
15309104 2SA1586-GR(TE85R) TRANSISTOR Q1,Q2 on Main 2 13519641 DD308-959F104Z50 CERAMIC CAPACITOR C1-C8,C18,C21 on PS 10
15319115 2SC4213-A(TE85L) TRANSISTOR Q3-Q7 on Main 5 # 02232878 6.3MV330SWB+T CHEMICAL CAPACITOR C9-C11 on PS,C22 on Main 3 +1
! 15319602 2SD1758 TL Q TRANSISTOR Q13 on Main 1 13639570 ECA1EM101B CHEMICAL CAPACITOR C16,C17 on PS on PS 2
15329533 RN2307(TE85R) TRANSISTOR Q9,Q10 on Main 2 00568312 SRG16V2200 2200UF/16V CAPACITOR(CHEMICAL) C31 on PS 1
15329532 RN1309(TE85L) TRANSISTOR Q11,Q12 on Main 2 13649270 ECA1CM222B 2200UF/16V CAPACITOR C24-C28 on PS 5
00341901 16MV470HC+T CHEMICAL CAPACITOR C12,C13 on PS,C65,C72,C94,C103,C210, 2 +6
DIODE Q't C211 on Main
15019126 1SS133 T-77 SWITCHING DIODE on 7SEG, on NUM D1-D30 23 +5 +2 01120990 ECA1VMI02 MO CAPACITOR (12.5X20/P.5.0MM) C14,C15 on PS 2
01011656 SLR-332VR3F LED (RED) on 7SEG, on NUM LED1-LED8 3 +5 01128323 35MV470HC CAPACITOR C19,C20,C22,C23 on PS 4
! 15039159T0 S5688G(TPA3) RECTIFIER DIODE D37 on PS 1 01674345 ECUV1H121JCV CERAMIC CAPACITOR C217-C222 on Main 6
! 01129723 W02A DIODE D34,D35 on PS 2 01674612 ECJ1VB1H103K CERAMIC CAPACITOR C7,C212-C216,C223,C224 on Main 8
! 01670667 D5SB20-4000 BRIDGE DIODE D36 on PS 1 01674167 ECUV1H100DCV CERAMIC CAPACITOR C18,C19,C80,C87,C90,C95,C99,C107,C111, 16
15019426 RD16ES-T1 AB2 ZENER DIODE D31,D32 on PS 2 C114,C132-C134,C157-C159 on Main
15339119T0 1SS352(TPH3) SWITCHING DIODE D1-D7 on Main 7 01674334 ECUV1H101JCV CERAMIC CAPACITOR C6 on Main 1
01127489 RB715F T106 SCHOTTKY DIODE DA1 on Main 1 01674356 ECUV1H151JCV CERAMIC CAPACITOR C70,C85 on Main 2
15339120T0 1SS302(TE85R) ARRAY DIODE DA2-DA4,DA6,DA7,DA10-DA15 on Main 11 01674467 ECUV1H102JCV CERAMIC CAPACITOR C82,C106 on Main 2
00237712 RD5.6MB3-T1B CHIP ZENER DIODE D8 on Main 1 01674512 ECJ1VB1H222K CERAMIC CAPACITOR C86,C98,C135-C137,C145-C147 on Main 8
01674578 ECJ1VB1H682K CERAMIC CAPACITOR C77 on Main 1
RESISTOR Q't
01674656 ECJ1VF1H223Z CERAMIC CAPACITOR C31,C43 on Main 2
13749793T0 SR25TRE 681 J 680 OHM 1/4W CARBON RESISTOR R9-R24 on 7SEG 16 01674701 ECJ1VF1E104Z 0.1UF/16VK CERAMIC CAPACITOR C1-C5,C8-C17,C20,C21,C24-C30,C32-C42, 100
13749797T0 SR25TRE 102 J CARBON RESISTOR on 7SEG, on NUM R1-R8 3 +5 C44-C56,C58-C61,C66-C68,C71,C73-C75,C78,
13749821T0 SR25TRE 103 J CARBON RESISTOR R26,R27 on PS 2 C79,C89,C93,C101,C102,C105,C109,C112,
13749813T0 SR25TRE 472 J CARBON RESISTOR R28,R29 on PS 2 C117-C119,C123,C126-C131,C140,C142,C144,
! # 02233090 RSS3 10 OHM J MTL.OXIDE RESISTOR R25 on PS 1 C149,C151,C153,C161,C163,C165,C168-C173,
00567323 RPC05T 223 J MTL.FILM RESISTOR R101,R105,R109-R112,R125,R129, 12 C179-C180,C183,C184,C206,C208,C209,
R133-R136 on Main C230-C232 on Main
00567312 RPC05T 183 J MTL.FILM RESISTOR R146,R147 on Main 2 13529132 RPE132-901F104Z50 MLT.LAY.CERAMIC CAPACITOR on Main 3
00566967 RPC05T 470 J MTL.FILM RESISTOR R28,R44,R54,R159,R172-R174 on Main 7 00239578 AMZV0050J473 0200 POLYEST. CAPACITOR C64,C84 on Main 2
00567278 RPC05T 822 J MTL.FILM RESISTOR R37,R100,R104,R108,R124,R128,R132 on Main 7 13639546M0 ECEA1CKA100B 10UF/16V CHEMICAL CAPACITOR C62,C63,C69,C81,C83,C92,C96,C97,C113,n 27
00566990 RPC05T 680 J MTL.FILM RESISTOR R176 on Main 1 C115,C116,C138,C166,C167,C174,C176,C177,
00566912 RPC05T 220 J MTL.FILM RESISTOR R178,R179 on Main 2 C188-C191,C193,C207 on Mai
00567034 RPC05T 121 J MTL.FILM RESISTOR R19,R41-R43 on Main 4 13639549M0 ECEA1CKA470B CHEMICAL CAPACITOR C91,C110 on Main 2
00567023 RPC05T 101 J MTL.FILM RESISTOR R21,R26,R27,R29,R55,R65,R69,R114,R116 12 13639511M0 ECA0JM221B CHEMICAL CAPACITOR C57 on Main 1
,R118,R171,R175 on Main 13639512M0 ECEA0JKA101B CHEMICAL CAPACITOR C76,C108,C120-C122,C160,C162,C164,C194, 19
00567156 RPC05T 102 J MTL.FILM RESISTOR R3,R39,R45,R46,R77,R78,R91,R92,R162-R165, 13 C197-C202,C204 on Main
R183 on Main 13639550M0 ECEA1CKA101B 100UF/16V CHEMICAL CAPACITOR C181,C182,C195,C196,C225,C226 on Main 6
00567378 RPC05T 473 J MTL.FILM RESISTOR R9,R72,R73,R80,R87,R89,R90,R144,R145, 13 13639602M0 ECEA1HKA010B UF 50V CHEMICAL CAPACITOR C23 on Main 1
R148-R151 on Main 13649159 ECEA1HKA4R7B CHEMICAL CAPACITOR C88,C104,C139,C141,C148,C150 on Main 8
00567389 RPC05T 563 J MTL.FILM RESISTOR R141 on Main 1 00674423 ECA0JM102B 1000U/6.3V CHEMICAL CAPACITOR C227 on Main 1
00567289 RPC05T 103 J MTL.FILM RESISTOR R1,R4,R6,R8,R10,R14,R16-R18,R22,R24,R35, 25
R40,R47,R63,R71,R76,R86,R88,R142,R153, INDUCTOR, COIL, FILTER Q't
R154,R158,R177,R180 on Main 00019567 SFC-6 LINE FILTER FERRITE CORE SFC-6 1
00567045 RPC05T 151 J MTL.FILM RESISTOR R30,R155 on Main 2 00903167 N2012Z601T02 (CHIP) FERRITE-BEAD L1,L2,L14-L22 on Main 11
00567245 RPC05T 472 J MTL.FILM RESISTOR R7,R74,R83,R161 on Main 4 12449452 BLM41A800SPT FERRITE-BEAD L11 on Main 1
00567267 RPC05T 682 J MTL.FILM RESISTOR R99,R103,R107,R123,R127,R131 on Main 6
CRYSTAL, RESONATOR Q't
00567301 RPC05T 153 J MTL.FILM RESISTOR R36,R181 on Main 2
00567412 RPC05T 104 J MTL.FILM RESISTOR R49,R50,R52,R67,R81,R82,R93,R94 on Main 8 01568889 MA-406 8.00MHZ CRYSTAL X1 on Main 1
00567190 RPC05T 222 J MTL.FILM RESISTOR R20,R23,R31,R33,R38 on Main 5 15299171 CST4.19MGW SERAMIC RESONATOR X3 on Main 1
00567501 RPC05T 474 J MTL.FILM RESISTOR R5,R25 on Main 2 # 02122445 1339-M1 67.7376MHZ OSCILLATOR X2 on Main 1
15399301 RPC10T 0R0 J MTL.FILM RESISTOR CN3 on Main 1 ENCODER Q't
# 02122623 RR0816R-104-D MTL.FILM RESISTOR R61,R137 on Main 2
01013223 EVQ VEM F01 24B ROTARY ENCODER EN1 on 7SEG 1
00567112 RPC05T 471 J MTL.FILM RESISTOR R64,R75,R113,R115,R117,R119-R121 on Main 8
00567067 RPC05T 221 J MTL.FILM RESISTOR R13,R15 on Main 2 CONNECTOR Q't
00566867 RPC05T 100 J MTL.FILM RESISTOR R53,R95-R97 on Main 4 # 02120056 24FE-BT-VK-N CONNECTOR CN5 on 7SEG 1
00567212 RPC05T 332 J MTL.FILM RESISTOR R11 on Main 1 13369901 IL-FPC-14SL-N CONNECTOR CN1 on NUM 1
00567345 RPC05T 333 J MTL.FILM RESISTOR R32,R34 on Main 2 ! 13429234 RTB-1.5-5 CONNECTOR CN9 on PS 1
00567556 RPC05T 105 J MTL.FILM RESISTOR R2,R160 on Main 2 # 02122456 14FE-ST-VK-N CONNECTOR CN5 on Main 1
# 00567590 RPC05T 225 J MTL.FILM RESISTOR R48,R66 on Main 2 # 02122467 24FE-ST-VK-N CONNECTOR CN4 on Main 1
# 01905001 RR0816P-103-D MTL.FILM RESISTOR R59,R62,R84 on Main 3 01344567 B10B-XH-A CONNECTOR CN6 on Main 1
01905012 RR0816P-123-D MTL.FILM RESISTOR R58,R70 on Main 2 ! 13369515 B5B-PH-K-S JST CONNECTOR CN8 on Main 1
01909734 RR0816P-682-D MTL.FILM RESISTOR R79 on Main 1 13369663 JST S3B-PH-K-S(3P) CONNECTOR CN1 on Main 1
# 02122589 RR0816P-222-D MTL.FILM RESISTOR R56 on Main 1
# 02122590 RR0816P-273-D MTL.FILM RESISTOR R57 on Main 1
# 01566912 RR0816P-333-D MTL.FILM RESISTOR R139 on Main 1
# 02124645 RR0816R-473-D MTL.FILM RESISTOR R68,R85 on Main 2
01670167 RSS2 L15 100 OHMJ MTL.OXIDE RESISTOR R51,R60 on Main 2
01903523 ERTJ1VR153J THERMISTOR RESISTOR R182 on Main 1
00126112 EXBV8V101JV RESISTOR ARRAY RA22-RARA31 on Main 10
00126134 EXB-A10E103J RESISTOR ARRAY RA10 on Main 1
15409113 EXBV8V103JV RESISTOR ARRAY RA1-RA3,RA5,RA9,RA14,RA18-RA21 on Main 10

6
Apr. 2000 VG-88

#
WIRING, CABLE
02123589 FUJI CARD 24X180-A5.0BB-P1.25-HBL8 CN4 on Main to CN5 on 7SEG
Q't
1
IDENTIFYING THE VERSION NUMBER
# 02123590 BAN CARD BNCD-P=1.25-K-14-100 CN5 on Main to CN1 on NUM 1
1. Turn the power off.
TRANSFORMER Q't 2. While pressing [CURSOR(DOWN)] and [COSM AMP] key,
# 02121189 100/120V PWR TRANS 1 +1 turn on power.
3. The version number is displayed.
# 02121190 230/240V PWR TRANS 1 +1 +1

AC CORD (INSTALLED) Q't

! # 71565334 100V AC CORD ASSY 1
! # 71567690 117V AC CORD ASSY 1
! # 71567789 230V AC CORD ASSY 1
! # 71567834 230VE AC CORD ASSY 1
! # 71567889 240VA AC CORD ASSY 1

SCREW Q't
40010245 SCREW 3X6 BINDING BZC 2
40011278 SCREW 3X8 BINDING TAPTITE-P FE ZC 20
40011312 SCREW 3X8 BINDING TAPTITE P FE BZC 2
40342578 SCREW 3X6 TAPTITE S BINDING BZC 19
40019123 SCREW 3X8 BINDING TAPTITE S BZC 14
40012512 SCREW 3X6 BINDING TAPTITE S ZC 9
40015945 SCREW 3X8 BINDING TAPTITE S FE ZC 5
40013001 SCREW 4X8 PAN W SEMS BZC 4
40123545 JACK NUT 9X11X2 HLJ0999-01-240 FE NI 6
40011745 HEX NUT M4 SPRING NUT FE ZC 3
40011856 INSULATING WASHER 3X8X0.8 FIBER-W 1
40016467 JACK WASHER M9.2X14X0.5 FENI 12
40011923 WASHER M9.1X13 INTERNAL TOOTH 1
40015989 HEX BOLT 6X67 HALF THREAD BZC 1
40016001 LOCK NUT M6 U BZC 1
40016067 PLAIN WASHER 6X13X1 BZC 2
40015901 E-RING M2.5 SUS 1

PACKING Q't
# 02232801 CARTON PAD 1
# 02232812 PAD B 2
# 02232823 PAD C 1
# 02232790 CORNER PAD 4
# 02123501 PACKING CASE 1 +1

MISCELLANEOUS Q't
12569249 LITHIUM BATTERY CR2032 220MAH/3V 1
22350312 BASE 6
00568945 PEDAL LABEL(BANK DOWN) 1
# 02122689 PEDAL LABEL (CTL) 1
# 02122656 PEDAL LABEL (2) 1
# 02122645 PEDAL LABEL (1) 1
# 02122678 PEDAL LABEL (4) 1
00568956 PEDAL LABEL(BANK UP) 1
# 02122667 PEDAL LABEL (3) 1
! # 02123678 INSULATING SHEET 2
01016267 SHAFT STAY 1
40017356 COATING CLIP CS-4 1
40347934 SILICON GREASE KS-64 100G 1
40016378 TRMINAL TER61-0171 TER1-TER7 on PS 7
12189815 BATTERY HOLDER BH-32 BT1 on Main 1
01120978 CUSHION 30X10X2 1
01016223 FOOT 30X10X3 1
22140315 HOLDER PIN PIN 214-315(FOR FV/EV) 1
22350171 RUBBER FOOT 235-171 7
22170103 SUPPORT SPRING (FOR SWITCH PEDAL) 7
! 40126812 CAUTION LABEL BARRIER(100V/117V ONLY) 1
40122645 NITTO FILAMENT TAPE #2883 W19MM 50M 60P (CM)
40122556 DOUBL FACED ADHESHIVE TAPE #575X W30MM 30M 10P 30CM
40235189 RING SE-9

ACCESSORIES (STANDARD) Q't

00349067 ORIGINAL CNECT CORD C-13A 1 +1
# 71565301 OWNER'S MANUAL JAPANESE 1
# 71567667 OWNER'S MANUAL ENGLISH 1
40232334 JAPAN ONLY 1

7
VG-88 Apr. 2000

USER DATA SAVE AND LOAD FACTORY PRESET

Transmitting/receiving all sound data Restoring the factory settings (Initialization)
The VG-88's system parameter and patch parameter settings To restore the factory settings of the VG-88, do as follows. You
can be transferred as a whole to or from an external device as can initialize all settings, or only a specified section of the patch
MIDI exclusive data. data in the user area or system settings.
If you use a MIDI sequencer that is able to record exclusive The following types of data can be initialized.
data, you can transmit system parameters and patch Display Data that is initialized
parameters to the MIDI sequencer, and save them on a floppy SYSTEM All system parameters
disk. Alternatively, you can directly connect two VG-88 units via #1-1 - #25-4 The setting contents of patches 1-1 - 25-4.
a MIDI cable, and transmit or receive parameters directly.
1. Turn off the power.
2. While holding [PAGE ] and [PAGE ] down, switch on the
Transmitting settings to an external device unit.
(BULK DUMP)
1. Make sure you're in Play page.
If you're not in Play page, press [EXIT] several times.
2. Press [F6] (SYSTEM).
3. Press [F5] (MIDI).
4. Press [PAGE ] several times to access the BULK DUMP
screen.

3. Move the cursor to "START" with [CURSOR], then use the

VALUE dial to get the display to show the data that is the
beginning point of the initialization.
4. Move the cursor to "END" with [CURSOR], then get the
display to show the ending point of the initialization, also
using the VALUE dial.
5. Press [WRITE].
5. Press [F1] (START), and use [CURSOR] to select the first The display will indicate "ARE YOU SURE?"
patch or system that you wish to transmit. 6. If you wish to initialize, press [WRITE].
6. Press [F4] (START), and use [VALUE] to specify the first The specified area of data will be initialized. The VG-88 will
data that you wish to transmit. then be in its normal power-on state.
7. Press [F2] (END), and use [CURSOR] to select the last ∗ If you decide not to initialize the settings, press [EXIT].
patch or system that you wish to transmit. Initialization will be canceled, and the normal power-on
8. Press [F5] (END), and use [VALUE] to specify the last data display will appear.
that you wish to transmit.
9. Press [F3] (DUMP). Transmission will begin.

10.Press [EXIT] several times to return to the Play page.

Receiving settings from an external device

(BULK LOAD)
You must use the following procedure to receive bulk dump
data from an external device.
1. Make sure you're in Play page.
If you're not in Play page, press [EXIT] several times.
2. Press [F6] (SYSTEM).
3. Press [F5] (MIDI).
4. Press [PAGE ] to access the BULK LOAD screen.

5. Bulk dump data will be received from the external device.

∗ If the display indicates "MIDI Receive Error !!," check the
connections and slow down the tempo of the transmitting
MIDI device.

6. Press [EXIT] several times to return to the Play page.

8
Apr. 2000 VG-88

HOW TO VERSION UP THE FLASH ROM 4. Send SMF data from the sequencer to the VG-88.

Play VG-88-1.MID from the sequencer.

When the VG-88 receives the MIDI signal, the 8-segment 2-
∗CAUTION digit LED's dot blinks.
Do not turn off the VG-88 main unit power while system
software is writing. Otherwise, the VG-88 will not work properly When playback of VG-88-1.MID is completed, the VG-88
due to system writing failure to the flash ROM. checks the received data.
After checking, the 8-segment 2-digit LED displays "o1".
∗CAUTION
When user data exist in the system, be sure to backup the data
in the sequencer (MC-50MK2, etc) before upgrading. Make sure that "o1" is displayed, then perform playback of
For the user data saving procedure, refer to "Data Saving and VG-88-2.MID from the sequencer.
Loading". When the VG-88 receives the MIDI signal, the 8-segment 2-
digit LED's dot blinks.

∗CAUTION Follow the same procedure to sequentially perform playback

After upgrading, perform "TEST:17. PEDAL CALIBRATION" of SMF data up to VG-88-8.MID
and "TEST:18.F ACTORY RESET" in the test mode.
4-1. Sequencer : Display VG-88-1.MID -> VG-88: 8-segment
2-digit LED displays "o1"
4-2. Sequencer : Display VG-88-2.MID -> VG-88: 8-segment
Items to be prepared 2-digit LED displays "o2"
1. Sequencer capable of SMF playing (MC-80 or equivalent) 4-3. Sequencer : Display VG-88-3.MID -> VG-88: 8-segment
2. Update disc (P/No.17048516) 2-digit LED displays "o3"
3. System update jig plug (P/No.17048536) 4-4. Sequencer : Display VG-88-4.MID -> VG-88: 8-segment
2-digit LED displays "o4"
4-5. Sequencer : Display VG-88-5.MID -> VG-88: 8-segment
2-digit LED displays "o5"
System update jig plug
4-6. Sequencer : Display VG-88-6.MID -> VG-88: 8-segment
2-digit LED displays "o6"
• Items to be prepared: ø6 STEREO plug 1pcs
4-7. Sequencer : Display VG-88-7.MID -> VG-88: 8-segment
: RESISTOR(47kΩ) 1pcs
2-digit LED displays "o7"
4-8. Sequencer : Display VG-88-8.MID -> VG-88: 8-segment
2-digit LED displays "o8"

5. After all SMF data have been received, the 8-segment 2-

digit LED displays the system software checksum in the
order of "upper 2 digits" and "lower 2 digits". Confirm the
checksum value.

6. Perform "TEST:17. PEDAL CALIBRATTION" and "TEST:18.

FACTORY RESET" in the test mode.

Updating is completed.

About update disc (P/No.)

VG-88 system data are in Standard MIDI File (SMF) data
format.

• The following SMF data are saved on each disk. Transfer data
from VG-88-1.MID to VG-88 main unit.

Disk 1 : VG-88-1.MID, VG-88-2.MID, VG-88-3.MID,

VG-88-4.MID
Disk 2 : VG-88-5.MID, VG-88-6.MID, VG-88-7.MID,
VG-88-8.MID

Note : Playback should be performed one at a time starting from

VG-88-1.MID, instead of continuously playing all SMF
data.

Operating Procedure
Update VG-88 main unit system by the following procedure.

1. Connect MIDI OUT connector of MIDI sequencer capable of

SMF data playback to MIDI IN connector of VG-88 using
MIDI cable.

2. Connect the system update jig plug to SUB EXP PEDAL/

SUB CTL 1,2 pins.

3. Turn VG-88 on while pressing [OUTPUT SELECT] and

[CURSOR(RIGHT)]
When the 8-segment 2-digit LED displays "dL" then "--", it is
ready to receive data.

9
VG-88 Apr. 2000

TEST MODE When the knob is turned clockwise??, the contrast will be come
sharper.
Precaution: When users' data are being stored, always make
backup the data in the sequencer (MC-50MK2),
etc. before starting the repair work. (For details of
the user's data storage method, refer to Sections
"Saving the data" and "Loading the data".)

Test items
0.VERSION 10.G/A PITCH
1.LCD CONTRAST 11.OUTPUT When the knob is turned clockwise??, the contrast will become
2.LCD DISPLAY 12.ESP TRS/TRR more moderate.
3.SWITCH/LED 13.INPUT(GUITAR)
4.EXP PEDAL 14.INPUT(GK)
5.SUB EXP PEDAL 15.NOISE(GUITAR → OUT)
6.BATTERY 16.NOISE(GK → OUT)
7.MIDI 17.PEDAL CALIBRATE
8.GK VOL 18.FACTORY RESET
9.GK DOWN/S2 UP/S2

Necessary parts and instruments

When the contrast of the LCD is changed in the order of "8 →
• Expression Pedal (Roland EV-5)
16 → 1", the equipment proceeds to the next inspection
• MIDI cable
automatically.
• Noise meter (DINAUDDIO)
• Oscilloscope (0.5mS/DIV, 2V/DIV)
• Oscillator (Rectangular waves 400Hz,5Vp-p and rectangular 2. LCD DISPLAY
waves 400Hz,40mVp-p) Press the [OUTPUT SELECT] switch 3 times in succession to
• Shorting plugs check that no abnormal indications appear on the LCD.
• Guitar equipped with GK-2A

How to enter the test mode

• Connect the expression pedal (EV-5) to the [SUB EXP
PEDAL/SUB CTL 1,2] jack.
• Connect the MIDI cable to the [MIDI IN] jack and the [MIDI
OUT] jack.
• Connect the guitar equipped with GK-2A to the GK IN jack.
When the switch is pressed for the 1st time (White) :
(1) To start from "0. VERSION" Check and make sure nothing appears on the display.
Turn on the power switch while depressing the [CURSOR
(DOWN)] button and the [NAME/CHAIN] button simultaneously.
The program version will appear on the display

When the switch is pressed for the 2nd time (Black) :

Check and make sure the whole screen is blackened out.

(2) To start from "10. G/A PITCH"

Turn on the power switch while depressing the [CURSOR(DOWN)]
button and the [PEDAL/ASSIGN] button simultaneously.

Regarding respective inspection items

0. VERSION When the switch is pressed for the 3rd time (Mosaic pattern) :
The program version will appear on the LCD. Check and make sure the whole screen becomes mosaic-
patterned.

1. LCD CONTRAST
Check if the LCD contrast changes when the [VALUE] encoder When the inspection is completed, the equipment proceeds to
knob is turned in the following order. the next inspection automatically.

10
Apr. 2000 VG-88

3. SWITCH/LED 5. SUB EXP PEDAL

Connect the EV-5 to the [SUB EXP PEDAL/SUB CTL 1,2] jack
Respective LEDs come on successively. in advance.
Check and make sure the respective LEDs for all the segments Now, check the movement of the pedal connected to the [SUB
are turned on and off accordingly. EXP PEDAL/SUB CTL 1,2] jack.

Lighting sequence :
Segment 7 LED → [GUITAR AMP] → [POWER AMP+SP/
RETURN] → [LINE/PHONES] → PEDAL[CTL] → PEDAL[4] →
PEDAL[3] → PEDAL[2] → PEDAL[1] → Segment 7 LED

Press the "+" indicated switches appearing on the LCD in the

sequence designated below.
First, step on the pedal to the center inclination (intermediate
value) and "OK" will appear on CENTER.

Switching sequence :
[F1] → [F2] → [F3] → [PAGE(<)] → [PAGE(>)] → [WRITE] →
[EXIT] → F6] → [F5] → [F4] → [COSM GUITAR] → [COSM
AMP] → [EFFECTS] → [LEVEL/BPM/KEY] → [PEDAL/ Step on the pedal further (to its maximum stroke) and "OK" will
ASSIGN] → [NAME/CHAIN] → [EZ EDIT] → [TUNER] → appear on PRESS.
[CURSOR(DOWN)] → [CURSOR(LEFT)] → [CURSOR(UP)] →
[CURSOR(RIGHT)] → [OUTPUT SELECT] → [BANK(DOWN)]
→ [BANK(UP)] → [CTL] → [4] → [3] → [2] → [1]

∗ If the wrong switch is depressed, a warning reading

"WRONG SWITCH!" appears on the LCD.

When the inspection is completed, the equipment proceeds to

the next inspection automatically. Finally, totally release the pedal (to its minimum stroke) and
4. EXP PEDAL "OK" will appear on RELEASE to conclude the pedal inspection.
Check the movement of the EXP pedal on the equipment.

When the inspection is completed, the equipment proceeds to

4-1 First, step on the pedal to the center inclination the next inspection automatically..
(intermediate value) and "OK" will appear on CENTER.
6. BATTERY
Voltage of the memory backup battery is indicated.

4-2 Step on the pedal further (to its maximum stroke) and "OK"
will appear on PRESS.
Press the [PAGE(RIGHT)] button to proceed to the next
inspection process.

4-3 Finally, totally release the pedal (to its minimum stroke)
and "OK" will appear on RELEASE to conclude the pedal
inspection.

When the inspection is completed, the equipment proceeds to

the next inspection automatically.

11
VG-88 Apr. 2000

7. MIDI 9. GK DOWN/S1 UP/S2

Connect the [MIDI IN] and [MIDI OUT] connectors using a Now, check the movement of the DOWN/S1 and UP/S2
single MIDI cable. switches connected to the GK IN jack.
If these are not connected by MIDI cable, the following
indication will appear and when it does, make the connections
using a MIDI cable.

First, press the DOWN/S1 switch.

When the two connectors are connected and if the status is

normal, <OK> will appear before proceeding to the next
inspection automatically.

Then, press the UP/S2 switch.

8. GK VOL
Now, check the movement of the SYNTH VOL connected to the
GK IN jack.

When the inspection is completed, the equipment proceeds to

the next inspection automatically.

10.G/A PITCH
First, turn the VR to the center point (intermediate value) and The equipment will inspect the movement of the gate arrays
"OK" will appear on CENTER. automatically.

When the knob is turned counterclockwise, "OK" will appear on

MIN. When the inspection is completed, the equipment proceeds to
the next inspection automatically.

When the knob is turned clockwise, "OK" will appear on MAX.

When the GK VOL inspection is completed, a result of DSP

check will appear on LCD.

When the DSP inspection is completed, the equipment

proceeds to the next inspection automatically.

12
Apr. 2000 VG-88

11. OUTPUT 12. ESP TRS/TRR

11-1 Input rectangular waves (400Hz,5Vp-p) through Pin No. 7 Since internally oscillated waveforms are output through the
of the GK IN connector (corresponds to the GK-2A OUTPUT L(MONO) and R jacks, check the waveform through
GUITAR SIGNAL) and check the waveforms being output the OUTPUT jack using an oscilloscope.
through the GUITAR OUTPUT jack.
Precaution : Perform the above check on both the L(MONO)
Also, since the output muting function is turned on and off and R jacks. Also, since the signals through the L
automatically, check and make sure muting is being and R jacks are mixed internally when the
effected properly. OUTPUT jack is used for the L(MONO) channel
only, always insert a blank plug into the R channel
when making L(MONO) channel measurement.

OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV

Insert a shorting plug into the GUITAR INPUT jack to check and OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV
make sure that the waveform output through the GUITAR
OUTPUT disappears.
13. INPUT (GUITAR)
11-2 Since internally oscillated waveforms are output through Input rectangular waves (400Hz,40mVp-p) through the GUITAR
the OUTPUT L(MONO), R and PHONES jacks, check the INPUT jack and check the output waveforms through the
output waveform using an oscilloscope. OUTPUT L(MONO) and R jacks.

Precaution : Perform the above check on both the L(MONO) Precaution : Perform the above check on both the L(MONO)
and R jacks. Also, since the signals through the L and R jacks. Also, since the signals through the L
and R jacks are mixed internally when the and R jacks are mixed internally when the
OUTPUT jack is used for the L(MONO) channel OUTPUT jack is used for the L(MONO) channel
only, always insert a blank plug into the R channel only, always insert a blank plug into the R channel
when making L(MONO) channel measurement . when making L(MONO) channel measurement.

Also, since the output muting function is turned on and off

automatically, check and make sure muting is being
effected properly.

Adjust the OUTPUT LEVEL to make sure the output waveform

level varies.

LEVEL MAX LEVEL MIN LEVEL MAX

OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV

OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV

13
VG-88 Apr. 2000

14. INPUT (GK) 14-3 Checking the 5th and 6th string circuits
Input the following signals simultaneously into Pin Nos. 1 The 5th string signals are output through the OUTPUT
through 6 (corresponds to the 1st string through the 6th of the L(MONO) jack and the 6th string signals through the OUTPUT
GK-2A). R jack. Press the [F3] button for a few times to check the output
waveforms.
Pin No. 1 (The 1st string) : Rectangular wave (400Hz,40mVp-p)
positive phase
Pin No. 2 (The 2nd string) :Rectangular wave (400Hz,40mVp-p)
negative phase
Pin No. 3 (The 3rd string) : Rectangular wave (400Hz,40mVp-p)
positive phase
Pin No. 4 (The 4th string) : Rectangular wave (400Hz,40mVp-p)
negative phase
Pin No. 5 (The 5th string) : Rectangular wave (400Hz,40mVp-p)
negative phase
Pin No. 6 (The 6th string) : Rectangular wave (400Hz,40mVp-p)
positive phase

Press the [F1], [F2] and [F3] buttons respectively to check and
make sure the output waveforms vary.
14-1 Checking the 1st and 2nd string circuits
The 1st string signals are output through the OUTPUT
L(MONO) jack and the 2nd string signals through the OUTPUT
R jack. Press the [F1] button a few times to check the output
waveforms.
OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV

Press the [PAGE(RIGHT)] button to proceed to "NOISE

(GUITAR → OUT)".

15. NOISE (GUITAR → OUT)

Precaution : Perform the check on both the L(MONO) and R
jacks. Also, since the signals through the L and R
jacks are mixed internally when the OUTPUT jack
is used for the L(MONO) channel only, always
insert a blank plug into the R channel when making
L(MONO) channel measurement.

OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV GUITAR INPUT : Connect the shorting plug.

Press the [F2] button to proceed to "Checking the 1st and 2nd OUTPUT LEVEL : MAX (when it is turned clockwise as far as it
string circuits". will go)
Check and make sure the residual noise is less than -70dBm
14-2 Checking the 3rd and 4th string circuits (DIN-AUDIO).
The 3rd string signals are output through the OUTPUT
L(MONO) jack and the 4th string signals through the OUTPUT
16. NOISE(GK → OUT)
R jack. Press the [F2] button a few times to check the output
Precaution : Perform the check on both the L(MONO) and R
waveforms.
jacks. Also, since the signals through the L and R
jacks are mixed internally when the OUTPUT jack
is used for the L(MONO) channel only, always
insert a blank plug into the R channel when making
L(MONO) channel measurement.

GK IN : Short Pin Nos. 1 (1st string) through 6 (6th string).

OUTPUT LEVEL : MAX (when turned clockwise as far as it will go)
Check and make sure the residual noise is less than -67dBm
(DIN-AUDIO).

OSCILLOSCOPE : 0.5mS/DIV, 2V/DIV

Press the [F3] button to proceed to "Checking the 5th and 6th
string circuits".

14
 pedal.
Apr. 2000

18. FACTORY RESET

17. PEDAL CALIBRATE

Push the [WRITE] button twice.

the next inspection automatically.

Now, write the factory preset data

Press the [WRITE] button to set the minimum value.

Press the [WRITE] button to set the maximum value.

Raise the EXP pedal all the way before releasing your hand.

Depress the EXP pedal all the way before releasing your hand.

When the adjustment is completed, the equipment proceeds to

Now, preset the maximum and minimum values for the EXP

GUITAR
OUTPUT OUTPUT L(MONO)
DAC BAL-> JK6
JK3 OUTPUT OUTPUT 2
2 ADC AK4522 UNBAL VR De-Em 4
4 INPUT 1
1 AK4522 IC23
Pre-Em
IC23
GUITAR DAC
INPUT BAL-> OUTPUT R
DSP AK4522 UNBAL JK7
JK5 ADC 2
IC30
BLOCK DIAGRAM

2 GK IN 4
4
ANALOG AK4522 ESP2 1
1 ADDRESS, DATA,
IC30
IC13 CS(ESP1,ESP2),
ADC TRR, TRCK, SYO PHONES
GK IN AK4522 JK4
2
ANALOG 3
GK IC31 DSP 1
CN9 GATE-ARRAY
1.SIG1 1
ESP2 LC22039CT-SA6
2.SIG2 1
2 ADC CLOCK
3.SIG3 2
3 GK IN IC11
4.SIG4 3 AK4522 IC12 DATA
4
5.SIG5 4 ANALOG 160*64dots
5 CONTRAST,
6.SIG6 5 IC32
6 GRAPHIC_LCD
7.GT.SIG 6 LCD_DISP
7
8.SY.VOL 7
8
9.N.C. 8
9
10.S1 9
10
11.S2 10 LCD
11
12.+7V 11 EN ENCODER
12 DRIVER
13.-7V 12 GATE A B
13
13
1
4
2

4M 4M IC35 IC37
DRAM DRAM
IC16 IC15 SW(PANEL,PEDAL)
LED(CTL)
ADDRESS, DATA, CS, WR, RD
INT-ZERO

256k SRAM
IC36 SUB EXP/CTL L
2
JK1
3
8M FLASH 1M SRAM 1M SRAM 1
GK-IN ANALOG GAIN CONTROL

IC5 IC2 IC4

CPU MIDI IN
GK VOL(VR) UPD703100(BP106) MIDI OUT
IC1 JK2
GK S1(SW)
GK S2(SW) EXP PEDAL
VG-88

15
VG-88 Apr. 2000

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CIRCUIT BOARD (MAIN BOARD ASSY)

For EU Countries

B Apparatus containing CAUTION ADVARSEL! ADVARSEL VARNING VAROITUS

Lithium batteries Danger of explosion if battery is
incorrectly replaced.
Lithiumbatteri - Eksplosionsfare ved
fejlagtig håndtering.
Eksplosjonsfare ved feilaktig skifte av
batteri.
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en
Paristo voi räjähtää, jos se on
virheellisesti asennettu.
Replace only with the same or Udskiftning må kun ske med batteri af Benytt samme batteritype eller en ekvivalent typ som rekommenderas av Vaihda paristo ainoastaan
C equivalent type recommended by the
manufacturer.
samme fabrikat og type.
Levér det brugte batteri tilbage til
tilsvarende type anbefalt av
apparatfabrikanten.
apparattillverkaren.
Kassera använt batteri enligt
laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo
Discard used batteries according to the leverandøren. Brukte batterier kasseres i henhold til fabrikantens instruktion. valmistajan ohjeiden mukaisesti.
manufacturer’s instructions. fabrikantens instruks joner.
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U View from components side. View from foil side.

16
Apr. 2000 VG-88

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CIRCUIT DIAGRAM (MAIN-1)

B EXP PEDAL
D +5 R3
D +5

C185
D +5

C186
D +5

C187
1 1k 10/16 10/16 10/16
1
2
2 C1 C2
3 D D D
3 C3 0.1 D +5 D +5 0.1 R1
IC2
LITHIUM BAT
C CN1
S3B-PH-K-S
D 0.1

D
D +5

C188
D +5

C189 D D
A17
A16
A15
A14
2
31
3
28
A16
A15
A14
I/O8
I/O7
I/O6
21
20
19
18
D15
D14
D13
D12
10k

100

126
10/16 10/16 LRCK A13 I/O5
IC1 A13 4 17 D11
INT_BPM1 A12 I/O4
A12 25 15 D10 3
SUB EXP/CTL D D RA19 INT_BPM2
A11 23
A11 I/O3
14 D9
-
4

HVDD

HVDD
EXBV8V103JV INT_ZERO A10 I/O2
A10 26 13 D8 1 +
DA2 A9 I/O1

D
A9 27
D +5 D +5 D +5 D +5 D +5 A8 IC3A
1SS302 1 127 8 1 D15 A8 5
R5 P07/DMARQ3/INTP103 P57/D15 RA25 A7 TC75S51F
1 2 2 128 7 2 D14 A7 6
470k R6 C191 C190 D +5 P06/DMARQ2/INTP102 P56/D14 EXBV8V101JV A6 D +5 R2
3 129 6 3 D13 A6 7
P05/DMARQ1/INTP101 P55/D13 A5

4
3
2
1
JK1 10 k D 10/16 10/16 D +5 4 130 5 4 D12 A5 8 DA1 R4

3
P04/DMARQ0/INTP100 P54/D12 A4 10 k 1M
2 1 8 5 131 8 1 D11 A4 9 RB715F
P03/TI10 P53/D11 A3

8
7
6
5
3 D D 2 7 6 132 7 2 D10 RA24 A3 10 2 1
C6 RA1 P02/TCLR10 P52/D10 EXBV8V101JV A2
1 3 6 7 133 6 3 D9 A2 11 1

5
6
7
8
P01/TO10 1 P51/D9 A1 NC

2
100 p DA3 EXBV8V103JV 4 5 8 134 5 4 D8 A1 12

3
D +5 D +5 RA20 P00/TO10 0 P50/D8 A0 BT1
HLJ 0544-01-010 1SS302
GK-IN 32

1
2
3
4
R7 EXBV8V103JV VDD
D 1 2 136 8 1 D7 30

1
D +5 P47/D7 CE2 BH-32
4.7k R8
10 k D
ANALOG-SW GK61
10
11
P17/DMAAK3/INTP113 P46/D6
137
138
7
6
2
3
D6
D5
RA23
EXBV8V101JV
22
29
CE1
C4
0.1 D

3
GK60 P16/DMAAK2/INTP112 P45/D5 R/W
12 139 5 4 D4 24 16
GK51 P15/DMAAK1/INTP111 P44/D4 OE VSS

8
7
6
5
13 140 8 1 D3
C7 RA2 GK50 P14/DMAAK0/INTP110 P43/D3 RA22 UPD431000AGW-70LL
14 141 7 2 D2 D
0.01 EXBV8V103JV GK41 P13/TI11 P42/D2 EXBV8V101JV D +5
15 142 6 3 D1

F D +5 GK40 P12/TCLR11 P41/D1

16 143 5 4 D0 IC4

1
2
3
4
P11/TO11 1 P40/D0 RA31
D 17 A17 2 21 D7
P10/TO11 0 A16 I/O8

5
EXBV8V101JV A16 31 20 D6
A15 I/O7

8
7
6
5
101 8 1 A15 3 19 D5 -
RA3 P67/A23 RA30 A14 I/O6 IC3B C5
18 102 7 2 A22 A14 28 18 D4
EXBV8V103JV GK31 P107/TC3/INTP123 P66/A22 EXBV8V101JV A13 I/O5 TC75S51F 0.1
19 103 6 3 A21 A13 4 17 D3 +
GK30 P106/TC2/INTP122 P65/A21 A12 I/O4
20 104 5 4 A20 A12 25 15 D2

1
2
3
4
P105/TC1/INTP121 P64/A20 RA29 A11 I/O3
21 105 8 1 A19 A11 23 14 D1

2
P104/TC0/INTP120 P63/A19 A10 I/O2

G GK21
GK20
GK11
GK10
22
23
24
25
P103/TI12
P102/TCLR12
P101/TO121
P100/TO120
P62/A18
P61/A17
P60/A16
106
107
108

109
7
6
5

8
2
3
4

1
A18
A17
A16

A15
EXBV8V101JV

RA28
EXBV8V101JV
A10
A9
A8
A7
A6
26
27
5
6
7
A9
A8
A7
A6
I/O1
13 D0

PB7/A15 RA27 A5
110 7 2 A14 A5 8
BATTERY PB6/A14 EXBV8V101JV A4
26 111 6 3 A13 A4 9
EXP PEDAL P77/AN I 7 PB5/A13 A3
27 112 5 4 A12 A3 10
P76/AN I 6 PB4/A12 A2

H
SUB PEDAL(VR) 28 113 8 1 A11 RA26 A2 11 1
SUB PEDAL(SW) P75/AN I 5 PB3/A11 EXBV8V101JV A1 NC
29 114 7 2 A10 A1 12
GK_SY.VOL P74/AN I 4 PB2/A10 A0
30 115 6 3 A9 32
P73/AN I 3 PB1/A9 VDD
31 116 5 4 A8 30
MIDI JK2
YKF51-5054
D +5 D +5
from GK_CN GK_VOL
32
33
P72/AN I
P71/AN I
P70/AN I
2
1
0
PB0/A8

PA7/A7
118 8 1 A7
22
29
CE2
CE1
R/W
C8
0.1
IN OUT Q1 R9 119 7 2 A6 24 16
2SA1586GR R11 47 k PA6/A6 OE VSS
2 2 7 D 120 6 3 A5
PA5/A5
2

4 5 4 5 8 3.3k 37 121 5 4 A4 C9 UPD431000AGW-70LL

I P20/NMI PA4/A4 D
9 1 MIDI_MUTE 38 122 8 1 A3 D +5 D +5 0.1
MIDI_OUT P21 PA3/A3
10 39 123 7 2 A2
P22/SO0/TXD0 PA2/A2

1
2
MIDI_IN 40 124 6 3 A1 R10
3

P23/SI0/RXD0 PA1/A1

5
L1 R13 D +5 SW_SCAN1 41 125 5 4 A0 10 k
3
2
1

4
5
6

1
2
N2012Z601 220 SW_SCAN2 P24/SCKO PA0/A0
42 A20 2 4
R14 SW_SCAN3 P25/SO1/TXD1
43
10 k SW_SCAN4 P26/SI1/RXD1 CN2 IC6
44 88

3
L2 R15 P27/SCK1 P93/WR R174 47 N.I.U. TC7SH04F IC5
89

J C10 N2012Z601 220 P92/RD R175 100

D 90 A19 16 45 D15
0.1 LED_CKS P91/UCAS/UWR R176 68 A18 */DQ15
2 1 4 3 46 91 D A18 17 43 D14
P37/SCK2 /INTP133 P90/LCAS/LWR A17 DQ14
47 A17 48 41 D13
IC7A IC7B LED_A P36/SI2/INTP132 A16 DQ13
48 A16 1 39 D12
TC74HC04AF TC74HC04AF D +5 LED_CKL P35/SO2/INTP131 C11 A15 DQ12
49 92 A15 2 36 D11
P34/INTP130 P87/RAS7/CS7 D +5 0.1 D +5 A14 DQ11
5 4 50 93 A14 3 34 D10
IC7C IC7D IC7E IC7F P33/TI13 P86/RAS6/CS6 A13 DQ10
14

6 3 51 94 A13 4 32 D9
TC74HC04AF TC74HC04AF TC74HC04AF TC74HC04AF P32/ TCLR13 P85/IORD/RAS5/CS5 CS5_CPU IC8 R16 A12 DQ9
7 2 52 95 A12 5 30 D8
P31/TO131 P84/IOWR/RAS4/CS4 CS4_CPU A11 DQ8

5
K 6 5 8 9 10 11 12 13
IC7G
TC74HC04AF
C12
0.1
8

D
1

RA21 LCD_DISP
53
P30/TO130 P83/RAS3/CS3
P82/RAS2/CS2
96
97
98
CS3_CPU
CS2_CPU
TC7SH32F
1
4
10 k A11
A10
A9
6
7
8
A10
A9
DQ7
DQ6
44
42
40
D7
D6
D5
7

EXBV8V103JV LCD_CONT SW_READ8 P81/RAS1/CS1 A8 DQ5

D D D D 54 99 2 A8 18 38 D4
SW_READ7 P117/SCK3/INTP143 P80/RAS0/CS0 R17 A7 DQ4
55 A7 19 35 D3
D +5 D +5 SW_READ6 P116/SI3/INTP142 10 k ROM Less Mode 0 A6 DQ3
D 56 A6 20 33 D2

3
R19 IC9 SW_READ5 P115/SO 3/ /INTP141 16bit Data B us CN3 A5 DQ2
57 70 A5 21 31 D1
SW_READ4 P114/ INTP140 MODE3 CLKSEL:PLL Mo de A4 DQ1
L3 120 PC410KT 58
P113/TI14 MODE2
69 ZERO-OHM D A4 22
A3 DQ0
29 D0
D +5

L
C13 R20 SW_READ3 59 68 A3 23
P112/ TCLR14 MODE1 A2
6

0.1 2.2k SW_READ2 60 67 D +5 A2 24 D +5

P111/TO141 MODE0 A1
2

N.I.U. 1 SW_READ1 61 66 D R177 A1 25 37

P110/TO140 CKSEL A0 VCC

1
2
D1 5 R18 10 k
R21 1SS352 3 D +3. 3 D +3. 3 D +3. 3 10 k 26 C14 C229

1
2
100 CE 0.1 N.I.U.
L4 72 144 11 46
1

D +5 P127/ADTRG/ INTP153 VDD WE VSS

73 45 15 27
4

R153 10k P126/ INTP152 VDD RY/BY VSS

74 62 28 9
R154 10k P125/ INTP151 CVDD OE NC D +5
N.I.U. 75 47 10

M
D P124/ INTP150 BYTE NC D
8
7
6
5

D 76 C15 C16 C17 12 13

CN4 P123/TI15 0.1 0.1 0.1 RESET NC
77 14
24FE-ST-VK-N RA18 GK_S1 P122/ TCLR15 D +5 NC C123
78 65
D +5 RA17 EXBV8V103JV GK_S2 P121/TO151 CVSS E28F800B5B70 0.1
79
1
2
3
4

N.I.U. FLASH_RY/BY(SHARP ONLY) P120/TO150

D
1 4 5 CKS R180 D
1 CKL D +5 10 k
2 3 6 80 63
To CN5 on PANEL SW BOARD

2 A CLKOUT/PX7 X2 A20 FA20 FD15

3 2 7 81 1 1 D15

N
3 WAIT/PX6

4
4 1 8 82 C18 D C223 C224 A19 1 FA19 FD14 1 D14
4 REFRQ/PX5 10p 0.01 0.01 FA18 FD13
5 A18 1 1 D13
5 X1 FA17 FD12
6 84 A17 1 1 D12
6 HLDRQ/P97 MA-406(8MHz) FA16 FD11
7 85 A16 1 1 D11

1
7 R158 HLDAK/P96 FA15 FD10
8 86 64 A15 1 1 D10
8 RA4 10 k OE/P95 X1 FA14 FD9
9
10
9
10 SW SCAN[1:4 ] N.I.U.
87
BCYST/P94 C19 D
D D A14
A13
1
1 FA13 FD8
1
1
D9
D8
11 1 8 36 D +5 10p A12 1 FA12 FD7 1 D7
11 AVREF

O 12
13
14
15
12
13
14
15
2
3
4
7
6
5
71
RESET AVDD
34

C20
0.1
A11
A10
A9
A8
1
1
1
1
FA11
FA10
FA9
FA8
FD6
FD5
FD4
FD3
1
1
1
1
D6
D5
D4
D3
5
6
7
8

FA7 FD2
16 35 A7 1 1 D2
DATA BUS

VSS
VSS
VSS

VSS
16 RA5 AVSS FA6 FD1
17 A6 1 1 D1
17
18
18 EXBV8V103JV D A5 1 FA5
FA4
FD0 1 D0
[D0-D15]
19
SW READ[1: 4] A4 1
4
3
2
1

9
83
117
135
19 D +5 D[0:15]

P
20 A3 1 FA3
20 UPD703100GJ-40-8EU FA2 D[0:15]
21 A2 1
21 R22 FA1
22 D A1 1
22 SW_READ1 10 k FA0 RA10 D +5
23 8 1 D A0 1
23 SW_READ2 EXBA10E103J
24 7 2
24 SW_READ3 CS0
6 3 CS0 1
5 4 SW_READ4

1
C216 CS1 1 CS1
5
6
7
8

RA8 0. 01

Q D
RA9
EXBV8V103JV
N.I.U.
D +5 D
CPU_RD 1 RD

9
8
A15 7
A17 5
A16 4
A18 3
A19 2
A20 10
RESET ADDRESS BUS
4
3
2
1

2
D +5
7 1 D3
[A0-A22]
RST
VCC NC
To CN1 on NUMBER SW BOARD

D
SW READ[5: 8] C21 NC
2
3
1SS352 RESET RESET A[0:22]

1
RA13 0.1 NC A[0:22]
8

R CN5 N.I.U. NC
14FE-ST-VK-N 8 1 SW_READ5
ANALOG MUTE 4
GND DLY
5
CPU_RD CPU_RD
7 2 SW_READ6
SW_READ7
D
IC10 C23
MAIN BOARD ASSY (1/3)
1
1
2
6
5
3
4 SW_READ8 D +5 M51953AFP 1/5 0 CPU_WR CPU_WR
2
3
3 71563501
8
7
6
5

4 D
4 RA14 D +5 D2
5
5

S 6
6
7
EXBV8V103JV R33
2.2k R34 IC37B
1SS352 C22
330/6.3
1
2
3
4

7 33 k TC7W14F
8
8 IC37D R23
9 3 5
9
2

10 D D +5 TC7W14F 2.2k
10 C43
11 1 D
11 IC37C D +5 0.022
12
12
8

13 TC7W14F R31 R24 Q2

3

13

T
14 6 2 C208 2.2k R32 D IC37A 10 k 2SA1586GR
14 0.1 33 k TC7W14F
D 1 7
4

MUTE
D D
C31
D 0.022 R25
470k
D

U -

17
VG-88 Apr. 2000

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CIRCUIT DIAGRAM (MAIN-2)

B RESET RESET
GA-ESP CD[0:7]
GA-ESP CA[0:13]
ESP(MASTER)->GA,ESP(SLAVE) TRSA[0:5]
C D +5
R172 47 TRCKO->TRCKI
RESET

109
126
CPU A[0:22] IC11

18
37
40
54
73
89
90
LC22039CT-SA6
A[0:22] SYO->SYI

.
.
.
.
.
.
.
.
.
D ESP(SLAVE)->ESP(MASTER) TRSB[0:5]
10
.

D[0:15]
CPU D[0:15] CA13
CA12
34
33
.
.
.
.
9
8
TRSA5
TRSA4 R173
CA11 32 7 TRSA3 47
. . D +5 D +5
CA10 31 6 TRSA2
. .
CA9 30 5 TRSA1
CA8 . .
29 4 TRSA0

108
109
126
134
144

108
109
126
134
144
. .
CA7 28 IC12 IC13

12
18
30
41
54
72
90

12
18
30
41
54
72
90
.

1
CA6 27 3

E CA5 26
. .

.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
.
CA4 25
.
CA3 24 35
. .
CA2 23 CA13 74 62 TRSA5 CA13 74 62 TRSB5
. . . . .
CA1 22 143 CA12 75 61 TRSA4 CA12 75 61 TRSB4
. . . . . .
CA0 21 142 CA11 76 60 TRSA3 CA11 76 60 TRSB3
. . . . . .
141 CA10 77 59 TRSA2 CA10 77 59 TRSB2
. . . . .
CD7 20 140 CA9 78 58 TRSA1 CA9 78 58 TRSB1

F
. . . . . .
CD6 17 139 CA8 79 57 TRSA0 CA8 79 57 TRSB0
. . . . . .
CD5 16 138 CA7 81 56 CA7 81 56
. . . . . .
CD4 15 137 CA6 82 CA6 82
. . . .
CD3 14 CA5 83 51 CA5 83 51
. . . . .
CD2 13 2 CA4 84 52 CA4 84 52
. . . . . .
CD1 12 CA3 85 CA3 85
. . .
CD0 11 41 CA2 86 53 CA2 86 53
. . . . . .
42 CA1 87 CA1 87
. . .

G A22
A21
A14
A13
82
81
80
79
.
.
.
.
.

.
44
43

118
116
CD7
CD6
CD5
CA0 88

92
93
94
.

.
.
.
.
.
.
101
102
103
104
105
TRSB5
TRSB4
TRSB3
TRSB2
TRSB1
CD7
CD6
CD5
CA0 88

92
93
94
.

.
.
.
.
.
.
101
102
103
104
105
TRSA5
TRSA4
TRSA3
TRSA2
TRSA1
. . . . . .
A12 78 114 CD4 95 106 TRSB0 CD4 95 106 TRSA0
. . . . . .
A11 77 112 CD3 96 107 CD3 96 107
. . . . R171 100 . .
A10 76 110 CD2 97 CD2 97
. . . .

H
A9 75 111 CD1 98 132 CD1 98 132
. . . . . .
Analog +15V A8 74
. .
113 CD0 99
. .
133 CD0 99
. .
133
A7 71 115
+ . .
A6 70 66 66
. . .
A5 69 136 67 49 67 49
. . . . . .
A4 68 133 48 48
. . . .
A3 67 134 68 47 68 47
CN6 . . . . . .
A A2 66 125 69 46 69 46
B10B-XH-A . . . . . .
A1 65 121 70 45 70 45

I
- . . . . . .
A0 64 129 44 44
. . D +5 . D +5 .
1
1 Analog -15V .
131
.
43
.
43
2 D15 63 132 64 42 64 42
2
3
3 D14 62
.
.
.
.
130 GA GA GA GA 65
.
.
.
.
39 CODEC 65
.
.
.
.
39
4
5
4
5
AD/DA +5V
+
D13
D12
61
60
.
.
.
.
128
124
144pin-1pin
D +5
18pin-19pin
D +5
36pin-37pin
D +5
39pin-40pin
D +5
D
.
.
38
37 DATA D
.
.
38
37
6 D11 59 122 36 36
6 . . . .
7 D10 58 120 35 ED07 35 ED17

J
7 . . C27 C28 C29 C30 . .
8 D9 57 119 111 34 ED06 111 34 ED16
8 C192 . . 0.1 0.1 0.1 0.1 . . . .
9 D8 56 117 112 33 ED05 112 33 ED15
9 100/6.3 . . . . R26 . .
10 D7 52 113 32 ED04 113 32 ED14
10 . . . 100 . .
D6 51 123 D D D D 114 10 ED03 114 10 ED13
. . . . OUTPUT L . .
D5 50 135 115 9 ED02 115 9 ED12
. . GA GA GA . . DA3 . .
D A D4 49 116 8 ED01 116 8 ED11
. . . OUTPUT R . .
D3 48 88 54pin-55pin 72pin-73pin 89,90pin-91,92pin 117 7 ED00 117 7 ED10
. . . . DA1 . .
D2 47 118 6 118 6
. . . . .

K
D +5 D1 46 97 D +5 D +5 D +5 5 R27 100 5
. . . .
D0 45 98 120 4 120 4 IC16
. . C32 C33 C34 . . INPUT AD3 . .
99 121 3 26 39 121 3 26 39
C194 . 0.1 0.1 0.1 . . A8 I/O16 5th,6th AD2 . . A8 I/O16
CS3_CPU 83 122 25 38 122 25 38
100/6.3 . . A7 I/O15 3rd,4th AD1 . A7 I/O15
CS4_CPU 84 107 123 24 37 123 24 37
. . . A6 I/O14 1st,2nd AD0 . A6 I/O14
85 106 D D D 136 23 36 136 23 36
CS2_CPU . . R155 150 . A5 I/O13 R28 47 . A5 I/O13
D Digital +5V CPU_WR 87
. .
105
GA GA
124
. .
137 22
A4 I/O12
34 124
. .
137 22
A4 I/O12
34
86 104 125 138 19 33 125 138 19 33
D +3. 3 CPU_RD . . D +5 LRCK . . A3 I/O11 FS . . A3 I/O11

L
108pin-109pin 126pin-127pin 139 18 32 139 18 32
. A2 I/O10 R29 100 . A2 I/O10
103 128 140 17 31 128 140 17 31
. D +5 D +5 . . A1 I/O9 . . A1 I/O9
94 102 129 141 16 10 ED07 129 141 16 10 ED17
C193 INT_ZERO . . C24 . . A0 I/O8 64FS . . A0 I/O8
95 101 142 9 ED06 142 9 ED16
10/16 INT_BPM1 . . C44 C45 0.1 . I/O7 . I/O7
96 100 130 27 8 ED05 130 27 8 ED15
INT_BPM2 . . 0.1 0.1 . . I/O6 256FS . . I/O6
131 26 7 ED04 131 26 7 ED14
. . I/O5 R30 150 . . I/O5
D CPU +3.3V .
38
.
25
I/O4
5 ED03
.
25
I/O4
5 ED13
D D D 24 4 ED02 24 4 ED12
. I/O3 . I/O3
CPU 53 29 23 3 ED01
CODEC 29 23 3 ED11

M Q13
2SD1758

2 3
<-->
.
.
93

2
11
.

.
.
.
.
.
22
21
20
17
11
12
15
30
NC
NC
NC
I/O2
I/O1
2

1
ED00

D +5
CLOCK 2
11
.

.
.
.
.
.
22
21
20
17
11
12
15
30
NC
NC
NC
I/O2
I/O1
2

1
ED10

D +5
GA 19
. .
16 D +5 NC VCC
6 19
. .
16 D +5 NC VCC
6
.
.
.
.
.
.
.
.
.
.

R183 . . VCC . . VCC

28 14 20 28 14 20
1
19
36
39
55
72
91
92
108
127

1K . RAS VCC C25 . RAS VCC C26

31 13 28 31 13 28
1

C226 . . UCAS 0.1 . . UCAS 0.1

40 14 29 21 40 14 29 21

N 100/16 . . LCAS VSS . . LCAS VSS

50 15 13 35 50 15 13 35
. . WE VSS . . WE VSS
2

27 40 27 40
D9 C225 OE VSS OE VSS
D D D
N.I.U. 100/16 D D LC324260AJ-60
IC15

.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
1

D +5 TC170C140AF-003 LC324260AJ-60 TC170C140AF-003

55
63
71
73
80
89
91

55
63
71
73
80
89
91
100
110
119
127
135
143

100
110
119
127
135
143
D8 X3
ESP(Slave) ESP(Master)

O RD5.6M-B3 CST4.19MGW C206

0.1
C207
10/16
D D
3

2 R160 ESP ESP ESP ESP ESP

21

D
R159 1M 1,144pin-2,143pin 12pin-11pin 18pin-19pin 30pin-31pin 41pin-40pin
47 17 50 IC36
VDD
1

OSC1 VA15 D +5 D +5 D +5 D +5 D +5
D 18 51 1 19 LCD7
OSC2 VA14 A14 I/O8

P
52 D 26 18 LCD6
VA13 A13 I/O7 C39 C40 C41 C42 C50
D7 29 53 2 17 LCD5
D7 VA12 A12 I/O6 ESP ESP ESP D +5 L11 R41 R42 R43 0.1 0.1 0.1 0.1 0.1
D6 28 54 23 16 LCD4
D6 VA11 A11 I/O5 BLM41A800S 120 120 120
D5 27 55 21 15 LCD3 1,144pin-2,143pin 12pin-11pin 18pin-19pin X2
D5 VA10 A10 I/O4
D4 26 56 24 13 LCD2 4 1 D D D D D
D4 VA9 A9 I/O3 D +5 D +5 D +5 VDD OE
D3 25 57 25 12 LCD1
D3 VA8 A8 I/O2 C61
D2 24 58 3 11 LCD0
D2 VA7 A7 I/O1 C35 C36 C37 0.1 ESP ESP ESP ESP ESP ESP
D1 23 59 4
D1 VA6 A6 0.1 0.1 0.1
D0 22 1 5 2 3 54pin-50pin 72pin-71pin 90pin-80,89,91pin 108,109pin-110pin 126pin-127pin 134pin-135pin

Q A0

CPU_RD
20

13
D0

A0

RD
VA5
VA4
VA3
VA2
VA1
2
3
4
5
6
7
8
9
A5
A4
A3
A2
A1
D +5
D D D
D
GND
1339-M1
67.7376MHz
OUT
D +5

C51
D +5

C52
D +5

C53
D +5

C58
D +5

C59
D +5

C60
14 6 10 28 0.1 0.1 0.1 0.1 0.1 0.1
CPU_WR WR VA0 A0 VDD ESP ESP ESP ESP ESP ESP ESP ESP
19
CS5_CPU CS C209
10 42 LCD7 20
LCD RESET RES VD7
43 LCD6 27
CE 0.1
30pin-31pin 41pin-40pin 54pin-50pin 72pin-71pin 90pin-80,89,91pin 108,109pin-110pin 126pin-127pin 134pin-135pin D D D D D D

R
VD6 R/W D +5 D +5 D +5 D +5 D +5 D +5 D +5 D +5
15 44 LCD5 22 14
SEL2 VD5 OE GND
LCD CN7 16
SEL1 VD4
45 LCD4
WIRING LCD D +5 RA15 46 LCD3 TC55257DFL-55L D C38 C46 C47 C48 C49 C54 C55 C56
DMF-50374NY-LY N.I.U. VD3 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
D 47 LCD2
VD2
1.FLM 1
1 8 1 41
YSCL VD1
48 LCD1
2.LP 2
2 7 2 40
YD VD0
49 LCD0 D D D D D D D D
3.CP 3
3 6 3 39
YDIS
4.M 4
4 5 4 38
WF D +5

S 5.VADJ
6.VCC 5
6
5
6
37
35
LP
XSCL VCE
8
8

7.VSS 7
7 RA16 34
XECL VWR
7
8.VEE 8
8 N.I.U.
VRD
9 - 6 -
9.D0 9
9 8 1 33
XD0
R182 7 IC17C
10.D1 10
10 7 2 32
XD1 NC
11 ERTJ1VR153J
+ 5 +
UPC4570G
11.D2 11 6 3 31 12
VSS

11 XD2 NC
12.D3 12 5 4 30 60 IC17B D
4

12 XD3 NC D +5
13.DISP

T
13 R181 R35 UPC4570G
13
14.LED_A 14 15k 10k -
36

14
15.LED_K 15
15 - R40 IC35 R36 R37 R38
10k SED1335F0B R39 15k 8.2K 2.2K
D 1k 2
- LCD_CONT
D D 1
+ 3
C57
IC17A D

U
LCD_DISP 220/6.3
UPC4570G
D

18
Apr. 2000 VG-88

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CIRCUIT DIAGRAM (MAIN-3)

1
+
D4
1SS352 C62 R45 C63 R46 L5 GUITAR OUT
C64 2 10/16 1k 10/16 1k N.I.U. JK3 R169 N.I.U. D6
-

1
0.047_Poly 1 2 C71 1SS352

2
3 3 0.1 C65 C66 C67 R178 22 C211 C68 R51
+

8
IC18A 1 + R53 470/16 0.1 IC20C 0.1 470/16 0.1 C69 2 100/2W
DA9 -
R48 UPC4072G2 R49 1 Q3 R50 10 UPC4570G IC21C 10/16 1

C - - -

2
N.I.U. + 2.2M 100k MUTE 2SC4213A 100k UPC4570G 3 +

3
1 2 R161 HLJ0544-01-110
+ + +

2
A A 4.7k A C76 A A A A IC19C C70 1 Q4
- A 100/6.3 C72 C73 C74 R170 N.I.U. C210 C75 M5216FP R52 IC19A 150p 2SC4213A

4
C77 R56 R57 470/16 0.1 0.1 470/16 0.1 100k M5216FP R164

2
R47 0.0068 2.2kD 27kD C197 C198 R179 22 R55 1k
10k R58 100/6.3 + + 100/6.3 A 100 A
12kD L6
PHONES
D R59 10kD C78 C79
-
OUTPUT VR D7
A N.I.U.

1
GUITAR IN C80 0.1 0.1 IC23 CN8 1SS352 JK4

1
A D5 10p AK4522VF B5B-PH-K-S R60 L7 HLJ0544-01-010
1SS352 C81 R61 R62 C82 C83 6 100/2W N.I.U. 2
-
JK5 L8 R63 C84 10/16 100kD R64 R65 10kD 0.001 10/16

18
6 - A D 7 3

2
6

1
HLJ0544-01-110 N.I.U. 10k 0.047_Poly 7 2 470 100 5 1
- +

3
1
2
3
4
5
2 5 1 4 13

VA

VREFH

VD
+ + AINL+ SDTO

E
3 IC18B 3 12 AD3 C87 R68 C85 1 Q5
+

1
2
3
4
5
R66 UPC4072G2 IC22A C86 SDTI 10p 47kD R67 IC19B 150p 2SC4213A
1 10 DA3
2.2M NJM2100M 0.0022 LRCK 100k M5216FP R165
11

2
SCLK
5
AINL- MCLKI
17 FS
R69 1k
OUTPUT
3
+ + R70 R71 R72 C90 100
A A A A
+
DA5
1 2 12kD C88
4.7/50
C89
0.1 DIF1
DIF0
9
8
64FS
10k 47k 10p
A
L(MONO)
N.I.U. + DA8 R185 R44 14 C91 C92 R73
SMUTE 256FS
1 2 N.I.U. N.I.U. 47 C95 R75 16 R76 6 47/16 10/16 47k C96 R77 C97 R78 L9 JK6

F
- DEM1 -
10p 470 A 15 10k 7 6 10/16 1k 10/16 1k N.I.U. HLJ0544-01-110
+ DEM0 -
C177 R79 2 21 5 7 2
+
3

10/16 6.8kD AINR+ CMODE IC20B

- 5 + 3

3
C93 C94 6 C98 D UPC4570G IC21B 1
-

8
0.1 470/16 7 0.0022 20 R80 C99 UPC4570G R81 1 Q6 R82
+ PD RESET
R142 L13 5 3 47k 10p A 100k 2SC4213A 100k
- + AINR-
10k L12 N.I.U. IC18C 22 CN11 CN10 R84 C106 R163

2
N.I.U. UPC4072G2 + C104 C105 AOUTL C107 10kD 0.001 1k
1 1 A A A

G
+ 1 1
A A IC22B 4.7/50 0.1 2 2 10p A

DGND
2 2

AGND
C102 NJM2100M 24 23

4
VCOM AOUTR

8
+ R74 0.1 C103 R85
4.7k 470/16 A RIBON CABLE 2X90-P2.0 R86 R87 47kD
-
C228 C112 C108 C212 10k 47k
OUTPUT

19
N.I.U. 0.1 100/6.3 C109 0.01
+
C227
1000/6.3
C100
100/6.3
C101
0.1
R83
4.7k
R184
N.I.U.
R54
47
IC22C
NJM2100M A
0.1
R88 2 -
C110
47/16
C111
10p R

4
H A D A D 10k 1 C113 R89
3 10/16 47k C115 R91 C116 R92 L10 JK7
+
A - A CN13 CN12 IC20A 2 10/16 1k 10/16 1k N.I.U. HLJ0544-01-110
-
1 1 UPC4570G A 1 2
1 1 R90 C114
2 2 3 + 3
2 2

3
C117 47k 10p IC21A 1
0.1 UPC4570G R93 1 Q7 R94
+ R95 RIBON CABLE 2X90-P2.0 100k 2SC4213A 100k
A A
10 R162

2
C118 A 1k A
0.1 A
GK11 GK10 C120 + R96
A
IC24A IC24B 100/6.3 10
TC4066BF TC4066BF GK31 GK30 MUTE
13

+ + IC25A IC25B
2 1 3 4 C199 C200 TC4066BF TC4066BF C121 C119

13
A

5
100/6.3 100/6.3 100/6.3 0.1

J 2 1 3 4 C201 C202 + R97

R99 R100 R101 100/6.3 + + 100/6.3 10
6.8k 8.2k 22k C126 C127 GK51 GK50
0.1 0.1 IC30 R103 R104 R105 IC26A IC26B
AK4522VF 6.8k 8.2k 22k C128 C129 TC4066BF TC4066BF C122

13
A

5
R110 C132 0.1 0.1 IC31 100/6.3
22k 10p R113 R114 AK4522VF 2 1 3 4 C203 C204
18

A D
6

2 470 100 R111 C133 100/6.3 + + 100/6.3

-

K
1 4 13 22k 10p R115 R116

18
A D
VA

VREFH

VD

AINL+ SDTO AD2

1
+ 3 12 2 470 100 R107 R108 R109
+ SDTI -
IC27A C135 10 1 4 13 6.8k 8.2k 22k C130 C131

VA

VREFH

VD
LRCK DA1 + AINL+ SDTO AD1
C138 NJM2100M 0.0022 11 3 12 0.1 0.1 IC32
SCLK FS + SDTI
5 17 IC28A C136 10 AK4522VF
10/16 AINL- MCLKI NJM2100M 0.0022 LRCK R112 C134
64FS 11 FS
GK21 GK20 C140 + SCLK 22k 10p R117 R118
9 5 17

18
DIF1 AINL- MCLKI A D

1
IC24C IC24D C139 0.1 8 C167 2 470 100
DIF0 256FS GK41 GK40 + 64FS -
TC4066BF TC4066BF 4.7/50 14 IC25D C142 9 1 4 13
12

VA

VREFH

VD
SMUTE 10/16 DIF1 AINL+ SDTO AD0
6

16 IC25C TC4066BF C141 0.1 8 + 3 12

DEM1 DIF0 256FS + SDTI
9 8 10 11 15 TC4066BF 4.7/50 14 IC29A C137 10

12
A DEM0 SMUTE LRCK

6
2 21 16 C175 NJM2100M 0.0022 11
AINR+ CMODE DEM1 SCLK
9 8 10 11 A 15 5 17
R123 R124 R125 R119 C145 DEM0 10/16 GK61 GK60 IC26D AINL- MCLKI
D 2 21 FS
6.8k 8.2k 22k 470 0.0022 AINR+ CMODE IC26C TC4066BF C144 +
20 RESET 9
PD R127 R128 R129 R120 C146 TC4066BF C143 0.1 DIF1
3 8

12
AINR- D DIF0 64FS

6
22 6.8k 8.2k 22k 470 0.0022 20 4.7/25 14

M
AOUTL PD RESET SMUTE
R134 C157 C149 3 9 8 10 11 16
AINR- DEM1 256FS
22k 10p C148 0.1 22 A 15
DGND

AOUTL DEM0
AGND

6 4.7/50 24 23 R135 C158 C151 2 21

- VCOM AOUTR AINR+ CMODE
7 22k 10p C150 0.1 R131 R132 R133

DGND
AGND
+ 5 A 6 4.7/50 24 23 6.8k 8.2k 22k R121 C147 D
+ - VCOM AOUTR
IC27B C213 7 470 0.0022 20 RESET
7

19

+ NJM2100M 0.01 + PD
5 + A 3
C166 IC24E IC28B C214 R136 C159 AINR-
22

19
+ AOUTL

N
TC4066BF C160 C174 NJM2100M 0.01 22k 10p C153
10/16
8

100/6.3 A D A D IC25E 6 C152 0.1

-

DGND
10/16 + +

AGND
C161 TC4066BF 4.7/25
14

- 7 24 23
IC27C C168 0.1 + VCOM AOUTR
A D A D 5 +
NJM2100M 0.1 C170 DA12 C162 C163 IC29B

14
+ A A
0.1 1SS302 + 8 100/6.3 0.1 C176 + NJM2100M C215

19
1 2 C171 A IC26E 0.01
-
4

IC28C C169 0.1 10/16 + TC4066BF

8
NJM2100M 0.1 C164

O
- +
3

7
100/6.3

14
A A - A D A D
IC29C C173 C165
4

L19 C219 A NJM2100M 0.1 C172 0.1

+
N2012Z601 120p 0.1 A
DA10 1SS302 + DA13 A

7
1 2 DA11 1SS302 + 1SS302 +
A
1 2 1 2
- A A

P
3

DA14 DA15
- -
3

1SS302 + 1SS302 + DA4 D +5

L17 C217 1 2 1 2 + 1SS302
N2012Z601 120p L18 C218 L20 C220 1 2
N2012Z601 120p N2012Z601 120p - - R137
3

GK-IN 3
A 100kD R139

3
1 A A 33kD D
1
1.SIG1 2
2 L21 C221 L22 C222
GK_VOL GK SY.VOL -> CPU
Q
2.SIG2 3
3 N2012Z601 120p N2012Z601 120p
3.SIG3 4
4 R141
4.SIG4 5
5 A A 56k
5.SIG5 6
6
6.SIG6 7
7 D
7.GT.SIG 8
8 L14 N2012Z601
8.SY.VOL 9
9
9.N.C. 10 C230 D +5 D +5
10
10.S1 11 0.1 DA6

R 11.S2 11
12
12 1SS302
D +5 D +5 R144
2

12.+7V 13
13 IC33 A 1 2 47k
13.-7V AN78L07M + R146 1 Q9
A
RN2307
L16 N2012Z601 18k
GK S1 -> CPU
3

CN9 1 3 D
3

TCS5095-114152 OUT IN C232 Q11

1
COM

RN1309 GK_S1
C179 C180 0.1
0.1 0.1 R148 R149

S
2

C181 C195 A 47k 47k

2

100/16 100/16
L15 N2012Z601 D D D
C231
A 0.1 D +5 D +5
DA7
1

C182 C183 C184 C196 A D +5 D +5 R145

1SS302
2

T
100/16 0.1 0.1 100/16 1 2 47k
COM

R147 1 Q10
RN2307
3 2 18k
GK S2 -> CPU
3

OUT IN
3

D
3

1 Q12
RN1309 GK_S2
IC34 -
AN79L07M R150 R151
2

47k 47k

U D D D

19
VG-88 Apr. 2000

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CIRCUIT BOARD (PWB SW SHEET)

B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
20
Apr. 2000 VG-88

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CUIT DIAGRAM (SW-1)

B
CUSOR OUTPUT CURSOR
C F1
SW30
SKQKAB
D30
1SS133
F2
SW29
SKQKAB
D29
1SS133
F3
SW28
SKQKAB
D28
1SS133
SW27
PAGE (-)
SKQKAB
D27
1SS133
PAGE (+)
SW26
SKQKAB
D26
1SS133
UP
SW10
SKQKAB
D10
1SS133
SELECT
SW8
SKQKAB
D8
1SS133
RIGHT
SW9
SKQKAB
D9
1SS133
1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2

D
SCAN 4

CURSOR CURSOR
F4 F5 F6 EXIT WRITE LEFT DOWN
SW21 D21 SW22 D22 SW23 D23 SW24 D24 SW25 D25 SW11 D11 SW12 D12
SKQKAB 1SS133 SKQKAB 1SS133 SKQKAB 1SS133 SKQKAB 1SS133 SKQKAB 1SS133 SKQKAB 1SS133 SKQKAB 1SS133
1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2

E SCAN 3 EXP PEDAL

LEVEL PEDALL NAME TO CN1 VR1A
COSM GUITAR COSM AMP EFFECT EZ EDIT TUNER
/BPM/KEY /ASSIGN /CHAIN on

1
1 RK11K1140

F SW20 D20 SW19 D19 SW18 D18 SW17 D17 SW16 D16 SW15 D15 SW14 D14 SW13 D13 1
2 2 4
CN5
24FE-BT-VK-N
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
SKQKAB
1 2 1
1SS133
2
MAIN 2
3
3

3
TO CN4 on MAIN BOARD

1
1
SCAN 2
BOARD CN4
WIRING EXP VR
2
2
3
3

G 4
5
6
4
5
6
7
READ 1
READ 2
READ 3
EXP VR BOARD ASSY
7 READ 4
8
9
8
9
10
READ 5
READ 6
71565256
10

H
11 READ 7
11 READ 8
12
12
13
13 EN1A
14
14 EN EVQ VEM F01 24B
15
15
16 A B
16
17

1
4
2
17
18
ENCODER
I 18
19
20
21
19
20
21
ENC A
ENC B

22
23
22
23
24
NUMBER BANK ASSY 71674745
24

J PANEL SW ASSY OUTPUT VR

IC1
M66312P VR2A
SW(DOWN) SW(UP)
16

D7 D6

13

23
RK14K12D0(10kAx2)

K 14 15 SW7 1SS133 SW6 1SS133

VCC

A QA R8 1k
1 12 22 1 2 1 2 1 2 1 2
QB
13 2
OE QC R7 1k
3 1 SKQKAH SKQKAH
QD 1
11 4
TO CN8 2

1
CKS QE R6 1k 2
5 3
QF 3
12 6 4
CKL QG 1
on 4

1
L
7 5
QH 5
1

10 LED7 LED8
GND

R
D +5 9
SQH
LED6
SLR-332VR3F SLR-332VR3F MAIN CN6
2

2
SLR-332VR3F
BOARD WIRING OUTPUT VR
8

M GUITAR_AMP POWER_AMP+SP LINE

5
4
3
2
1

/RETURN /HEADPHONES
BANK SW ASSY

1
2
3
5
4
3
2
1

CN7 CN3

1
2
3
RIBON CABL 5X40-P2.0 RIBON CABL 3X70-P2.0

N CN8
RIBON CABL 5X40-P2.0
5
4
3
2
1

LED9
5
4
3
2
1

D +5

O R10 680 16
A1
CN2

1
2
3
RIBON CABL 3X70-P2.0
R9 680 15

1
2
3
B1
D
R16 680
IC2
M66310P R15 680
3

2
C1
SW(1) SW(2) SW(3) SW(4) SW(CTL)
D1
3

D1 D2 D3 D4 D5

P 1 R14 680 1 14 SW1 1SS133 SW2 1SS133 SW3 1SS133 SW4 1SS133 SW5 1SS133
VCC

QA E1 COM1
2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2
QB
QC
QD
24
23
R23 680 18
F1 TO CN5 on MAIN BOARD CN1 SKQKAH SKQKAH SKQKAH SKQKAH SKQKAH
4 22 R24 680 17 IL-FPC-14SL-N
A QE G1 SCAN 1
21
QF R17 680
20 4 1

Q 5

8
OE
QG
QH
QI
QJ
19
18
17
16 R12 680 11
DP1 1
2
3
4
2
3
4
5
READ 1
READ 2
READ 3
CKS QK A2 5 READ 4
6 15 6
CKL QL R11 680 10 6 READ 5
14 7
QM B2 7 READ 6
7 13 8

R
R QN R21 680 8 READ 7
11 8 9
QO C2 9
12 10
GND

QP R19 680 10
10 6 13 11
SQP D2 COM2 11
12
R18 680 12
5 13
NUMBER SW ASSY
9

E2 13
14
R13 680 12 14 LED5
F2

S R20

R22
680

680
7

9
G2

DP2
LED4
LED3
LED2
LED1 R1 1k R2 1k R3 1k R4 1k R5 1k

1
SL-1264H LED1 LED2 LED3 LED4 LED5
7SEG BOARD ASSY SLR-332VR3F SLR-332VR3F SLR-332VR3F SLR-332VR3F SLR-332VR3F

T
2

2
GND

7SEG PANEL SW ASSY 71674756

U
21
VG-88 Apr. 2000

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A CIRCUIT DIAGRAM (SW-2)

B
C
D
E
F D37
S5688G
1 2
R25
10/3W LCD LED_Backlight
C31
2200/16

G IC3
UPC2933HF D +3.3

AC SW 1
IN OUT
3

COM
H TER1 TER2
C2
0.1/50
C1
0.1/50
C9
330/6.3 CPU

2
TER7
TER61-0171 TER61-0171

TER3
+3.3V
1

1
TER61-0171 TER61-0171

I 1

TER4
1

TER61-0171 1
IC4
PQ05RF21
2
D
D +5
IN OUT
1

GND
1
D36 4
D5SB20 OE
DIGITAL

+
J TER6 TER5 2 4 C26 C27 C28 C4 C3 C10

3
TER61-0171 TER61-0171 2200/16 2200/16 0.1/50 0.1/50
+5V

~
2200/16
330/6.3
1 1

-
3
AC CORD TRANS D

K IC5
AN7705F +
1 3

TO CN6 on MAIN BOARD

IN OUT

COM
1
D35

L
W02A
+

2 4 C24 C25 C6 C5 C11

AD/DA +5V

2
2200/16 2200/16 0.1/50 0.1/50
~

330/6.3 CN10
-

CN9
3

1 10
1 10
9
9

M 3
4
5
6
3
4
5
6
Q3
2SC2120Y
Q1
2SD2012
8
7
6
5
8
7
6
5
+ 4
4
2 1 2 3 3
RTB-1.5-5 3
2
2

N
R29 R26 1
4.7K 10K 1
ANALOG

1
C15 C20 C7 C12
C29 1000/35 470/35 0.1/50 470/16
+15V WIRING 10P(POWER)

2
N.I.U.
D34 C21 C23 D32 C17
1

W02A 0.1/50 470/35 RD16ES 100/25

O
+

1
2 4
~

2
-

C18 C22 D31 C16 A

3

0.1/50 470/35 RD16ES 100/25

C30 C14 C13 ANALOG

1
P
N.I.U. 1000/35
3
C19
470/35
C8
0.1/50
470/16
-15V

1
R28 R27
PS BOARD ASSY 4.7K
2 1
10K
2 3

71565267 Q4
2SA1015GR
Q2
2SB1375
-

Q
R
S
T
U
22
Apr. 2000 VG-88

ERROR MESSAGES DATA : DSP(IC13) : pins 7-10, 32-35 ↔ DRAM(IC16) : pins 2-10
ADDRESS : DSP(IC13) : pins 16-26 ↔ DRAM(IC16) : pins 16-19, 22-26
TEST : 6.BATTERY WE : DSP(IC13) : pin 13 ↔ DRAM(IC16) : pin 13
If the battery voltage for memory back-up is "2.7V" or less, the CAS : DSP(IC13) : pin 14 ↔ DRAM(IC16) : pin 29
display shows "BATTERY LOW !". RAS : DSP(IC13) : pin 15 ↔ DRAM(IC16) : pin 14

If no battery connected, the display shows "NO BATTERY !". Symptom : DRAM(IC15) returns data which is different from that
written to it through DSP(IC12).
∗ Check the following parts and assosiated wirings.
DATA : DSP(IC15) : pins 7-10, 32-35 ↔ DRAM(IC12) : pins 2-10
ADDRESS : DSP(IC15) : pins 16-26 ↔ DRAM(IC12) : pins 16-19, 22-26
WE : DSP(IC15) : pin 13 ↔ DRAM(IC12) : pin 13
CAS : DSP(IC15) : pin 14 ↔ DRAM(IC12) : pin 29
RAS : DSP(IC15) : pin 15 ↔ DRAM(IC12) : pin 14

∗ Replace with a new lithium battery of the same type. If the

error condition still exists, check the following parts and
associatd wirings.
CPU(IC1) : pin 26
OP.Amp(IC3) : pins 1-5
Resistor(R1, R2, R4)
Diode(D1) Symptom : GATE ARRAY(IC11) returns data which is different
Capacitor(C4,C8) from that written to it through DSP(IC12,13).
SRA<(IC2, IC4):pin 32 ∗ Check the following parts and assosiated wirings.
TEST : 7.MIDI GATE ARRAY(IC11) : pins 21-34 ↔ DSP(IC12):pins 74-88 ↔ DSP(IC13):pins 74-88
GATE ARRAY(IC11) : pins 11-20 ↔ DSP(IC12):pins 92-99 ↔ DSP(IC13):pins 92-99
GATE ARRAY(IC11) : pin 41 ↔ DSP(IC13):pin 68
GATE ARRAY(IC11) : pin 42 ↔ DSP(IC12):pin 68
GATE ARRAY(IC11) : pin 44 ↔ DSP(IC12):pin 69 ↔ DSP(IC13):pin 69
GATE ARRAY(IC11) : pin 43 ↔ DSP(IC12):pin 70 ↔ DSP(IC13):pin 70
TEST : 10.G/A PITCH
Symptom : The pitch data of GATE ARRAY(IC11) is not correct.
Symptom : No connect MIDI IN jack to MIDI OUT jack via the
MIDI cable.
Symptom : Transmitted data (MIDI OUT) and received data
(MIDI IN) don't agree with eack other.
∗ Check the following parts and assosiated wirings.
MIDI IN
CPU(IC1) : pin 40
Resister(R19,R20,R21)
Capacitor(C13) ∗ Check the following parts and assosiated wirings.
Photo Coupler(IC9)
Diode(D1) GATE ARRAY(IC11) : pin 94 ↔ CPU(IC1) : pin 4
MIDI OUT
CPU(IC1) : pins 38,39 TEST : 11.OUTPUT
Resister(R9,R11,R13-R15) Symptom : The waveform is not shown as below on the
Gate IC(IC7):pins 1-4 oscilloscope.
Transistor(Q1)
Inductor(L1,L2)

TEST : DSP CHECK (After TEST:8.GK VOL)

Symptom : DRAM(IC16) returns data which is different from that

written to it through DSP(IC13).
∗ Check the following parts and assosiated wirings. ∗ Check the following parts and assosiated wirings.

CPU(IC1) : pin 76, Resister(R23-R25,R161-R165),Diode(D2),Capacitor(C22),Transister(Q2-Q7)

23
VG-88 Apr. 2000

TEST : 12.ESP TRS/TRR

Symptom : The waveform is not shown as below on the
oscilloscope.

∗ Check the following parts and assosiated wirings.

GATE ARRAY(IC11) : pins 4-10 ↔ DSP(IC12) :pins 57-62 ↔ DSP(IC13) : pins 101-107
GATE ARRAY(IC11) : pin 3, DSP(IC12) : pin 56, DSP(IC13) : pin 56, R172, R173
DSP(IC12) : pins 101-106 ↔ DSP(IC13) : pins 57-62
DSP(IC12) : pin 107, DSP(IC13) : pin 56, R171

24