E.

Parameter
i) Test parameter
ii) External Parameters
iii) Calculated test
iv) Profile
vi) Carry over
vii) Reflex test
F. Schedule
i) Calibration schedule
ii) QC Schedule
iii) Sample Schedule
iv) work list
v) LIS
G.Run Monitor
i) Sample
ii) Reagent
iii) Cuvettes
iv) Warning
v) Dilution Run
H. Stat
I. Statistics
i) Historical Results
ii) Historical Data
iii) Charge Statistics
iv) Search
J. Report
i) Patient information
ii) Results
iii) Reaction Curve
K. Quality Control
i) QC Lot
ii) Selective QC
iii) Monthly QC
iv) QC Value print
 Maximum 500
Maximum 2000

Analyzer PC
383

548 Unit : mm
Front

The laboratory should be large enough, so that the analyzer and computer will not be crowded.

1.2 Installation
After unpacking, please take out the chemistry analyzer from the packing, and put it in a flat surface.
1.2a Connecting Water Supply Bucket

Tube of long plastic cannula

Tube of short plastic cannula

Down arrow water interface

Up arrow water interface

15
Biohazard
1 Confirm that the Analysis Division Power is turned off
keep the waste liquid bucket to a right place which is under work desk.
2 Let the liquid level sensor into waste

1.2f Installing/Removing Sample-Reaction Disk

Warning:
Before inserting or removing the sample / reagent tray please make sure that the analyzer stops
working or is turned off, the sample / reagent tray is stopped.
Biohazard
While operating, wear gloves, wear overalls to prevent cloths from being infected, if necessary,
wear protective glasses
To install the sample-reagent disk, grasp the ring, make the circular groove of sample/reagent disk
alignment with relevant groove in the disk, lay down slightly, paste tightly with bottom refrigeration
piece.

Caution
When Sample / reagent positions and sample / reagent tray in use may be contaminated by the
samples. Analysis Division of the power is turned off when the sample spilled into the sample /
reagent positions on the sample / reagent tray should, as soon as possible with dip the cloth with
water or disinfectant wipe.

17
Installing/Removing Reagent Bottles

Warning:

When installing the reagent bottle, you should confirm that the sample / reagent tray, sampler needle
are in the stopped state.
Use specified sample containers only.

Bio-hazard:
While operating, you must wear gloves, wear overalls to prevent them from being infected, if
necessary, wear protective glasses.

To load reagent bottles, insert the bottle into the bottle holder until the bottom of the bottle contacts
the groove of the holder.
To remove reagent bottles, grab the bottle and pull it upward to remove it from the bottle holder.

Installing/Removing Reaction Cuvette

Bio-hazard:
While operating, you must wear gloves, wear overalls to prevent them from being infected, if
necessary, wear protective glasses.
Abandoned reaction cup shall comply with the relevant provisions for proper handling.
Align the positioning column in a row on the reaction cup bracket holes on the reaction plate, and
then tighten the set screw to mount joint reaction cuvettes by Installed one by one.
Rotary positioning screws, pick up reaction cuvette bracket, you can take out a joint reactioncuvette,
then replace the cuvettes.

Fuse Installation Steps

Turn off the power, Spin out of the fuse holder back cover with a Phillips screwdriver, take out the
broken fuse, insert the new type of the fuse into the fuse holder back cover, Use a Phillips screwdriver
to tighten the fuse holder back cover, the fuse is the specified model, and the specification is
5×20，T10A L 250V.

CAUTION:
When replacing the fuse, you must first cut off the power, replace the fuse of the same specifications,
to prevent electric shock, malfunction. For the risk of electric shock, replacing of the fuse should be by
professionals.

18
iii) Appearance:

Merilyzer AutoQuant 100i Biochemistry Analyser【Please see below picture】

2.2b Parts & Consumables

26
27
28
5. INSTRUMENT DESCRIPTION

I) System Structure

This Part mainly describes the structure and interface and other basic operations of AutoQuant
100i automatic Bio -Biochemistry Analyzer
The full name of the system is AutoQuant 100i Automatic Biochemistry Analyzer, It is intended for
in vitro diagnostic use and quantitative determination of clinical chemistries samples, such as
serum, plasma, urine or cerebrospinal fluid.

Note:

Some samples may not be analyzed on the system based on parameters and the testing
reagents. For these samples, you can consult the reagent manufacturer or distributor for details.

Dome Arm

CRU
RCT

RGT

Stirrer

Water Syringe Cover Cabinet

Power Connection Air Inlet Air Outlet

36
iii)Mixer Assembly

Stirrer Paddle Trough Stirrer Arm

The mixer assembly of AutoQuant 100i consists of rabble, mixer arm and drive shaft. It mixes
reaction liquid in the reaction cuvette.
For single-reagent test, the mixer works once sample adding is finished; for double-reagent test,
the mixer works after adding sample and R2 respectively.
When stirring is finished, the mixer moves automatically to the wash well and washes.

Warning:

When the analyzing unit is in operation, do not place any part of your body or any obstacle in the
direction the arm moves. Otherwise, it may lead to personnel injury or equipment damage.

iv)Reaction Disk Assembly

Cuvette

Cuvette Holder
Cuvette Disk

38
Cuvette Holder
Knob

Reaction Disk
Knob

Cuvette Holder

Cuvette

39
 Remove right side
top cover

Remove four screw

Lamp heatsink

Lamp holder

Unscrew this screw and

40
6.ANALYZER OPERATION

41
42
43
44
C. BRIEF ABOUT SOFTWARE FEATURES:

Main Menu

45
46
47
ii) operator details:

48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
Parameters in this interface:

iv) Search:

Select a desired query and click “Search” to index to results.

70
Statistics — Search — Search way select— By Patient name:

Statistics — Search — Search way select— No. of Patient:

Parameters in this interface:

Parameter Function
Patient information column Click the test in “Patient information column” to display
results in the “Tested result” column
Tested result column Displays the selected tested results
Sort By Six methods:Date, patient name, No.of Patient, Doctor
name, QA inspector and all patients.
Search Click it to search the results that meet your requirements.

71
72
73
74
75
76
77
78
79
80
iv) Initialization:

After doing instrument settings, Initialization needs to be done by pressing initialization button.

80
81
82
83
7. TROUBLESHOOTING

84
85
86
87
88
89
90