SAFETY DATA SHEET

Hyspin HLP 32
Safety Data Sheet according to GB/T 16483-2008 and GB/
T 17519-2013

Section 1. Identification
GHS product identifier Hyspin HLP 32
Product code 469040-CN02
SDS no. 469040
Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/ Hydraulic fluid.
mixture For specific application advice see appropriate Technical Data Sheet or consult our
company representative.
Manufacturer
Supplier BP (China) Industrial Lubricants Co., Ltd.
19-22F, Youyou International Plaza
No. 76 Pujian Rd. Shanghai P.R.C. , 200127
Tel: +86 21 38605888
EMERGENCY TELEPHONE Carechem: +86 10 5100 3039 (24/7)
NUMBER

Section 2. Hazards identification

Classification of the SHORT-TERM (ACUTE) AQUATIC HAZARD - Category 3
substance or mixture
GHS label elements
Signal word No signal word.
Hazard statements H402 - Harmful to aquatic life.
Precautionary statements
Prevention P273 - Avoid release to the environment.
Response Not applicable.
Storage Not applicable.
Disposal P501 - Dispose of contents and container in accordance with all local, regional,
national and international regulations.
Other hazards which do not Defatting to the skin.
result in classification Note: High Pressure Applications
Injections through the skin resulting from contact with the product at high pressure
constitute a major medical emergency.
See 'Notes to physician' under First-Aid Measures, Section 4 of this Safety Data
Sheet.

Section 3. Composition/information on ingredients

Substance/mixture Mixture
Highly refined base oil (IP 346 DMSO extract < 3%). Proprietary performance additives.
Ingredient name % CAS number
Distillates (petroleum), hydrotreated heavy paraffinic ≥90 64742-54-7
Base oil - unspecified ≤10 Varies - See Key to
abbreviations
Alkylphosphorothioate, long-chain alkyl amine ≤0.1 -

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 1/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 3. Composition/information on ingredients
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact In case of contact, immediately flush eyes with plenty of water for at least 15
minutes. Eyelids should be held away from the eyeball to ensure thorough rinsing.
Check for and remove any contact lenses. Get medical attention.
Inhalation If inhaled, remove to fresh air. Get medical attention if symptoms occur.
Skin contact Wash skin thoroughly with soap and water or use recognised skin cleanser.
Remove contaminated clothing and shoes. Wash clothing before reuse. Clean
shoes thoroughly before reuse. Get medical attention if symptoms occur.
Ingestion Do not induce vomiting unless directed to do so by medical personnel. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery
position and get medical attention immediately. Get medical attention if adverse
health effects persist or are severe.
Indication of immediate medical attention and special treatment needed, if necessary
Notes to physician Treatment should in general be symptomatic and directed to relieving any effects.

Note: High Pressure Applications

Injections through the skin resulting from contact with the product at high pressure
constitute a major medical emergency. Injuries may not appear serious at first but
within a few hours tissue becomes swollen, discoloured and extremely painful with
extensive subcutaneous necrosis.
Surgical exploration should be undertaken without delay. Thorough and extensive
debridement of the wound and underlying tissue is necessary to minimise tissue
loss and prevent or limit permanent damage. Note that high pressure may force the
product considerable distances along tissue planes.
Specific treatments No specific treatment.
Protection of first-aiders No action shall be taken involving any personal risk or without suitable training. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Most important symptoms/effects, acute and delayed
See Section 11 for more detailed information on health effects and symptoms.

Section 5. Firefighting measures

Extinguishing media
Suitable extinguishing Use foam or all-purpose dry chemical to extinguish.
media
Unsuitable extinguishing Do not use water jet.
media
Specific hazards arising Fire water contaminated with this material must be contained and prevented from
from the chemical being discharged to any waterway, sewer or drain. In a fire or if heated, a pressure
increase will occur and the container may burst. This material is harmful to aquatic
life.
Hazardous thermal Combustion products may include the following:
decomposition products carbon oxides (CO, CO2) (carbon monoxide, carbon dioxide)
Special protective actions No action shall be taken involving any personal risk or without suitable training.
for fire-fighters Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire.
Special protective Fire-fighters should wear positive pressure self-contained breathing apparatus
equipment for fire-fighters (SCBA) and full turnout gear.

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 2/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
For non-emergency Contact emergency personnel. No action shall be taken involving any personal risk
personnel or without suitable training. Evacuate surrounding areas. Keep unnecessary and
unprotected personnel from entering. Do not touch or walk through spilt material.
Avoid breathing vapour or mist. Provide adequate ventilation. Put on appropriate
personal protective equipment. Floors may be slippery; use care to avoid falling.
For emergency responders Entry into a confined space or poorly ventilated area contaminated with vapour, mist
or fume is extremely hazardous without the correct respiratory protective equipment
and a safe system of work. Wear self-contained breathing apparatus. Wear a
suitable chemical protective suit. Chemical resistant boots. See also the
information in "For non-emergency personnel".
Environmental precautions Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air). Water polluting material. May be harmful
to the environment if released in large quantities.
Methods and material for containment and cleaning up
Small spill Stop leak if without risk. Move containers from spill area. Absorb with an inert
material and place in an appropriate waste disposal container. Dispose of via a
licensed waste disposal contractor.
Large spill Stop leak if without risk. Move containers from spill area. Approach the release
from upwind. Prevent entry into sewers, water courses, basements or confined
areas. Contain and collect spillage with non-combustible, absorbent material e.g.
sand, earth, vermiculite or diatomaceous earth and place in container for disposal
according to local regulations. Contaminated absorbent material may pose the
same hazard as the spilt product. Dispose of via a licensed waste disposal
contractor.

Section 7. Handling and storage

Precautions for safe handling
Protective measures Put on appropriate personal protective equipment (see Section 8). Do not ingest.
Avoid contact with eyes, skin and clothing. Avoid breathing vapour or mist. Keep in
the original container or an approved alternative made from a compatible material,
kept tightly closed when not in use. Empty containers retain product residue and
can be hazardous. Do not reuse container. Avoid contact of spilt material and
runoff with soil and surface waterways.
Advice on general Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Wash thoroughly after handling. Remove
contaminated clothing and protective equipment before entering eating areas. See
also Section 8 for additional information on hygiene measures.
Conditions for safe storage, Store in accordance with local regulations. Store in original container protected
including any from direct sunlight in a dry, cool and well-ventilated area, away from incompatible
incompatibilities materials (see Section 10) and food and drink. Keep container tightly closed and
sealed until ready for use. Store and use only in equipment/containers designed for
use with this product. Containers that have been opened must be carefully resealed
and kept upright to prevent leakage. Do not store in unlabelled containers. Use
appropriate containment to avoid environmental contamination.

Not suitable Prolonged exposure to elevated temperature

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 3/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure limits
Ingredient name Exposure limits
Distillates (petroleum), hydrotreated heavy paraffinic ACGIH TLV (United States).
TWA: 5 mg/m³ 8 hours. Issued/Revised:
11/2009 Form: Inhalable fraction
Base oil - unspecified ACGIH TLV (United States).
TWA: 5 mg/m³ 8 hours. Issued/Revised:
11/2009 Form: Inhalable fraction

Appropriate engineering All activities involving chemicals should be assessed for their risks to health, to
controls ensure exposures are adequately controlled. Personal protective equipment should
only be considered after other forms of control measures (e.g. engineering controls)
have been suitably evaluated. Personal protective equipment should conform to
appropriate standards, be suitable for use, be kept in good condition and properly
maintained.
Your supplier of personal protective equipment should be consulted for advice on
selection and appropriate standards. For further information contact your national
organisation for standards.
Provide exhaust ventilation or other engineering controls to keep the relevant
airborne concentrations below their respective occupational exposure limits.
The final choice of protective equipment will depend upon a risk assessment. It is
important to ensure that all items of personal protective equipment are compatible.
Environmental exposure Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and
safety showers are close to the workstation location.
Eye/face protection Safety glasses with side shields.
Skin protection
Hand protection Wear protective gloves if prolonged or repeated contact is likely. Wear chemical
resistant gloves. Recommended: Nitrile gloves. The correct choice of protective
gloves depends upon the chemicals being handled, the conditions of work and use,
and the condition of the gloves (even the best chemically resistant glove will break
down after repeated chemical exposures). Most gloves provide only a short time of
protection before they must be discarded and replaced. Because specific work
environments and material handling practices vary, safety procedures should be
developed for each intended application. Gloves should therefore be chosen in
consultation with the supplier/manufacturer and with a full assessment of the
working conditions.
Skin protection Use of protective clothing is good industrial practice.
Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product.
Cotton or polyester/cotton overalls will only provide protection against light
superficial contamination that will not soak through to the skin. Overalls should be
laundered on a regular basis. When the risk of skin exposure is high (e.g. when
cleaning up spillages or if there is a risk of splashing) then chemical resistant aprons
and/or impervious chemical suits and boots will be required.

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 4/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 8. Exposure controls/personal protection
Respiratory protection In case of insufficient ventilation, wear suitable respiratory equipment.
The correct choice of respiratory protection depends upon the chemicals being
handled, the conditions of work and use, and the condition of the respiratory
equipment. Safety procedures should be developed for each intended application.
Respiratory protection equipment should therefore be chosen in consultation with
the supplier/manufacturer and with a full assessment of the working conditions.

Section 9. Physical and chemical properties

Appearance
Physical state Liquid.
Colour Yellow. [Light]
Odour Not available.
Odour threshold Not available.
pH Not available.
Melting point Not available.
Boiling point Not available.
Drop Point Not available.
Flash point Open cup: >175°C (>347°F) [Cleveland.]
Evaporation rate Not available.
Flammability (solid, gas) Not applicable. Based on - Physical state
Lower and upper explosive Not available.
(flammable) limits
Vapour pressure Not available.
Vapour density Not available.
Relative density Not available.
Density <1000 kg/m³ (<1 g/cm³) at 15°C
Solubility insoluble in water.
Partition coefficient: n- Not available.
octanol/water
Auto-ignition temperature Not available.
Decomposition temperature Not available.
Viscosity Kinematic: 32 mm2/s (32 cSt) at 40°C
Kinematic: 5.5 mm2/s (5.5 cSt) at 100°C

Section 10. Stability and reactivity

Reactivity No specific test data available for this product. Refer to Conditions to avoid and
Incompatible materials for additional information.
Chemical stability The product is stable.
Possibility of hazardous Under normal conditions of storage and use, hazardous reactions will not occur.
reactions Under normal conditions of storage and use, hazardous polymerisation will not
occur.
Conditions to avoid Avoid all possible sources of ignition (spark or flame).
Incompatible materials Reactive or incompatible with the following materials: oxidising materials.
Hazardous decomposition Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 5/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 11. Toxicological information
Information on toxicological effects

Information on likely routes Routes of entry anticipated: Dermal, Inhalation.

of exposure
Potential acute health effects
Eye contact No known significant effects or critical hazards.
Inhalation Vapour inhalation under ambient conditions is not normally a problem due to low
vapour pressure.
Skin contact Defatting to the skin. May cause skin dryness and irritation.
Ingestion No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Eye contact No specific data.
Inhalation No specific data.
Skin contact Adverse symptoms may include the following:
irritation
dryness
cracking
Ingestion No specific data.

Delayed and immediate effects as well as chronic effects from short and long-term exposure
Eye contact Potential risk of transient stinging or redness if accidental eye contact occurs.
Inhalation Overexposure to the inhalation of airborne droplets or aerosols may cause irritation
of the respiratory tract.
Skin contact Prolonged or repeated contact can defat the skin and lead to irritation, cracking and/
or dermatitis.
Ingestion Ingestion of large quantities may cause nausea and diarrhoea.
Short term exposure
Potential immediate Not available.
effects
Potential delayed effects Not available.
Long term exposure
Potential immediate Not available.
effects
Potential delayed effects Not available.
Potential chronic health effects
General No known significant effects or critical hazards.
Carcinogenicity No known significant effects or critical hazards.
Mutagenicity No known significant effects or critical hazards.
Teratogenicity No known significant effects or critical hazards.
Developmental effects No known significant effects or critical hazards.
Fertility effects No known significant effects or critical hazards.

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 6/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 12. Ecological information
Toxicity
Environmental effects This material is harmful to aquatic life.

Persistence/degradability
Expected to be biodegradable.

Bioaccumulative potential
This product is not expected to bioaccumulate through food chains in the environment.

Mobility in soil
Soil/water partition Not available.
coefficient (KOC)
Mobility Spillages may penetrate the soil causing ground water contamination.

Other adverse effects No known significant effects or critical hazards.

Other ecological information Spills may form a film on water surfaces causing physical damage to organisms.
Oxygen transfer could also be impaired.

Section 13. Disposal considerations

Disposal methods The generation of waste should be avoided or minimised wherever possible.
Significant quantities of waste product residues should not be disposed of via the
foul sewer but processed in a suitable effluent treatment plant. Dispose of surplus
and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Waste packaging should be recycled.
Incineration or landfill should only be considered when recycling is not feasible. This
material and its container must be disposed of in a safe way. Care should be taken
when handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Avoid dispersal of spilt
material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information

China IMDG IATA
UN number Not regulated. Not regulated. Not regulated.

UN proper - - -
shipping name
Transport hazard - - -
class(es)

Packing group - - -
Environmental No. No. No.
hazards
Additional - - -
information

Special precautions for user Not available.

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 7/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 14. Transport information
Matters needing attention for Ensure that any additional local government transport conditions are met
transportation

Section 15. Regulatory information

Safety, health and No known specific national and/or regional regulations applicable to this product
environmental regulations (including its ingredients).
specific for the product
Regulation according to other foreign laws
REACH Status For the REACH status of this product please consult your company contact, as
identified in Section 1.
Australia inventory (AICS) All components are listed or exempted.
Canada inventory All components are listed or exempted.
China inventory (IECSC) All components are listed or exempted.
Japan inventory (ENCS) All components are listed or exempted.
Korea inventory (KECI) All components are listed or exempted.
Philippines inventory All components are listed or exempted.
(PICCS)
Taiwan Chemical All components are listed or exempted.
Substances Inventory
(TCSI)
United States inventory All components are listed or exempted.
(TSCA 8b)

Section 16. Other information

History
Date of printing 30/01/2019
Date of issue/Date of 30/01/2019
revision
Date of previous issue 08/06/2018
Version 1.04
Prepared by Not available.
Key to abbreviations ACGIH = American Conference of Industrial Hygienists
CAS Number = Chemical Abstracts Service Registry Number
GHS = Global Harmonised System
IATA = International Air Transport Association, the organisation
IMDG = International Maritime Organization Rules, rules governing shipment of
goods by water.
OEL = Occupational Exposure Limit
REACH = Registration, Evaluation, Authorisation and Restriction of Chemicals
Regulation [Regulation (EC) No. 1907/2006]
SDS = Safety Data Sheet
STEL = Short term exposure limit
TWA = Time weighted average
UN Number = United Nations Number, a four digit number assigned by the United
Nations Committee of Experts on the Transport of Dangerous Goods.
Varies = may contain one or more of the following 64741-88-4, 64741-89-5,
64741-95-3, 64741-96-4, 64742-01-4, 64742-44-5, 64742-45-6, 64742-52-5,
64742-53-6, 64742-54-7, 64742-55-8, 64742-56-9, 64742-57-0, 64742-58-1,
64742-62-7, 64742-63-8, 64742-65-0, 64742-70-7, 72623-85-9, 72623-86-0,
72623-87-1
References Not available.
Indicates information that has changed from previously issued version.
Notice to reader

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 8/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)
Section 16. Other information
All reasonably practicable steps have been taken to ensure this data sheet and the health, safety and environmental
information contained in it is accurate as of the date specified below. No warranty or representation, express or implied
is made as to the accuracy or completeness of the data and information in this data sheet.

The data and advice given apply when the product is sold for the stated application or applications. You should not use
the product other than for the stated application or applications without seeking advice from BP Group.

It is the user’s obligation to evaluate and use this product safely and to comply with all applicable laws and regulations.
The BP Group shall not be responsible for any damage or injury resulting from use, other than the stated product use
of the material, from any failure to adhere to recommendations, or from any hazards inherent in the nature of the
material. Purchasers of the product for supply to a third party for use at work, have a duty to take all necessary steps to
ensure that any person handling or using the product is provided with the information in this sheet. Employers have a
duty to tell employees and others who may be affected of any hazards described in this sheet and of any precautions
that should be taken. You can contact the BP Group to ensure that this document is the most current available.
Alteration of this document is strictly prohibited.
Date of issue/Date of revision : 30/01/2019 Date of previous issue : 08/06/2018 Version : 1.04 9/9

Product name Hyspin HLP 32 Product code 469040-CN02 Page: 9/9

Version 1.04 Date of issue 30/01/2019 Format China Language ENGLISH
China (ENGLISH)