Scribd
Upload
169 views3 pages

Combo Heat Press Machine Intruduction

This document provides instructions for operating a combo heat press machine. It lists safety cautions and preparation steps, including checking the power supply and grounding, setting the appropriate temperature and time based on the object, and not touching hot surfaces. It explains how to set the initial heating temperature, highest temperature, and time using the mode and plus/minus keys. Finally, it provides steps for pressing different objects like T-shirts, mugs, and caps, including closing the pressure handle, waiting for the temperature to reach the initial or highest setting, and hearing a sound when pressing is finished.

Uploaded by

Hippocomputo Linsy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
169 views3 pages

Combo Heat Press Machine Intruduction

This document provides instructions for operating a combo heat press machine. It lists safety cautions and preparation steps, including checking the power supply and grounding, setting the appropriate temperature and time based on the object, and not touching hot surfaces. It explains how to set the initial heating temperature, highest temperature, and time using the mode and plus/minus keys. Finally, it provides steps for pressing different objects like T-shirts, mugs, and caps, including closing the pressure handle, waiting for the temperature to reach the initial or highest setting, and hearing a sound when pressing is finished.

Uploaded by

Hippocomputo Linsy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Combo Heat Press Machine Intruduction

CAUTION:
1. for continued protection against fire,disconnect power-supply before
using the machine,check the power-supply grounded connection well
before using.
2. disconnect power-supply before replacing different-function heat uints
3. put in the object going to be shaped,close up the pressure handle and
rotate the adjusting screw to get a proper pressure.
4. the surface of the heat unit is hot during heat pressing,do not touch them without proper
protection.

BASIC PREPARATION BEFORE USING


1. plug the three-core power line into the outlet,check whether the power
supply is in conformity with the rated voltage of the machine, there should be a reliable
grounded wire for the power supply.
2. put in the object going to be shaped,close up the handle and rotate the
adjusting screw to get a proper pressure (the pressure of the mug press unit is a screw.)
3. turn on the power switch, and the instrument board will display the temperature .
4. set the temperature and time according to the table below and get the
specific corresponding temperature and timing setting.

Press object initial temperature highest temperature time


Mugs 230 330 40
Tiles 230 330 40
Metal board 230 300 40
Plate 355 355 150

T-shirt 355 355


Cap 355 355

Sublimation paper: 30~50 sec


T-shirt transfer paper: 10~20 sec

Learn to set the temperature and time


1. press the mode key once, see the “set” key turning red. Press the plus“+” or minus
key“-” to set the initial heating temperature.
2. press the mode key for the second time, see the “Temp” key turns red, Press the plus“+” or
minus key“-” to set the highest heating temperature.
3. press the “mode” key for the third time, when you see the “time light” turn red, Prees the plus
or minus key to set the proper heating time.
4. press the “mode” key for the fourth time ,finish the setting and the machine stands by to work.
Attention:
The initial heating temperature should be set between 200~380,the highest heating temperature
should be set between 200~430. the timing should be set between 0~999 sec.
IF the initial heating temperature is 230, the highest heating temperature should be set only
between 230~430. as the same , IF the highest heating temperature is 380, the initial heating
temperature should be set only between 200~380.
initial heating temperature always =< highest heating temperature>
Operation:
1. T-shirt and plate:
Close up the pressure handle, preset the corresponding temperature and timing for the object
that is going to be shaped, it needs a few minutes to achieve the initial heating temperature
When the temperature achieves the initial heating temperature, it will turn into constant
temperature status automatically. Pull up the handle, put into the object and close up the
handle. press the executive key, then close up the pressure handle, wait for a few
times(set),you will hear a hint sound ,the pressing is finished, pull up the pressure handle, p
ress the executive key. do the next object or turn off the power
2. mugs,tiles,metal board:
Preset the corresponding temperature and timing for the object that is going to be shaped. put
into the object, close up the pressure handle, Press the executive key, the temperature will
straight to achieves the highest heating temperature, wait for a few times(set), you will hear a
hint sound ,the pressing is finished, pull up the pressure handle, press the executive key. Do
the next object or turn off the power.
3. Caps
Close up the pressure handle ,preset the corresponding temperature and timing for the object that
is going to be shaped, it needs a few minutes to achieve the initial heating temperature
When the temperature achieves the initial heating temperature, it will turn into constant
temperature status automatically. Pull up the handle,put into the object and close up the handle.
press the executive key, then close up the pressure handle, wait for a few times(set),you will hear
a hint sound ,the pressing is finished, pull up the pressure handle, press the executive key. do the
next object or switch the power off.

You might also like