Annex To The Technical Catalogue Low Voltage Switch-Disconnectors and Automatic Circuit-Breakers For Direct Current Applications

Annex to the technical catalogue Emax DC
Low voltage switch-disconnectors

and automatic circuit-breakers for
Direct Current Applications
1SDC200012D0201
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Index
SACE Emax DC automatic circuit-breakers . ........................................................................... 2
SACE Emax DC switch-disconnectors for applications up to 1000 V DC . ............................. 3
SACE Emax DC: Direct Current Applications .......................................................................... 4
Protection trip units and trip curves ......................................................................................... 8
Accessories ............................................................................................................................ 23
Overall dimensions ................................................................................................................. 24
Circuit diagrams ..................................................................................................................... 33
Ordering codes . ..................................................................................................................... 42

SACE Emax DC automatic circuit-breakers
The SACE Emax range of low voltage automatic circuit-breakers is being enriched by the new series
SACE Emax DC of automatic circuit-breakers for direct current applications in compliance with the
international standard IEC60947-2.
Thanks to the exclusive technology of the new electronic SACE PR123/DC e PR122/DC the SACE Emax
DC range allows to cover all installation and automatic protection needs up to 1000V / 5000A DC.
By connecting three breaking poles in series it is possible to achieve a rated voltage of 750V DC,
while with four poles in series the limit rises 1000V DC.
The automatic circuit-breakers of SACE Emax DC range maintain the overall dimensions and fixing
points of the standard range circuit-breakers; they can be fitted with the various terminal kits and all
accessories common to the SACE Emax range.
The withdrawable circuit-breakers should be used together with the special version fixed parts for
applications at 750/1000 DC.
Common data
Voltages
Rated service voltage Ue [V–] 1000
Rated insulation voltage Ui [V] 1000
Rated impulse withstand voltage Uimp [kV] 12
Operating temperature [°C] -25....+70
Storage temperature [°C] -40....+70
Number of poles 3-4
Versions Fixed -

E2 E3 E4 E6
Performance levels B N N H S H H
Rated uninterrupted current (at 40 °C) Iu [A] 800 800
[A] 1000 1000
[A] 1250 1250
[A] 1600 1600 1600 1600 1600
[A] 2000 2000 2000
[A] 2500 2500 2500
[A] 3200 3200 3200
[A] 4000
[A] 5000
Rated ultimate breaking capacity under short-circuit Icu
@ 500 V DC (III) [kA] 35 50 60 85 75 100 100
@ 750 V DC (III) [kA] 25 25 40 40 65 65 65
@ 750 V DC (IV) [kA] 25 40 50 50 65 65 65
@ 1000 V DC (IV) [kA] 25 25 35 40 50 65 65
Rated service breaking capacity under short-circuit Ics [%Icu] [kA] 100% 100% 100% 100% 100% 100% 100%
Rated short-time withstand current Icw (0.5s)
@ 500 V DC (III) [kA] 35 50 60 65 75 100 100
@ 750 V DC (III) [kA] 25 25 40 40 65 65 65
@ 750 V DC (IV) [kA] 25 40 50 50 65 65 65
@ 1000 V DC (IV) [kA] 25 25 35 40 50 65 65
Rated making capacity under short-circuit Icm [%Icu] [kA] 100% 100% 100% 100% 100% 100% 100%
Utilization category (according to CEI EN 60947-2) B B B B B B B
Isolation behaviour (according to CEI EN 60947-2) ■ ■ ■ ■ ■ ■ ■
Overcurrent protection
Electronic trip units for DC applications ■ ■ ■ ■ ■ ■ ■
Operating times
Closing time (max) [ms] 80 80 80 80 80 80 80
Breaking time for I<Icw (max) (1) [ms] 70 70 70 70 70 70 70
Breaking time for I>Icw (max) [ms] 30 30 30 30 30 30 30
Overall dimensions
Fixed: H = 418 mm - D = 302 mm - W (3/4 poles) [mm] 296/386 296/386 404/530 404/530 566/656 566/656 782/908
Withdrawable: H = 461 mm - D = 396.5 mm - W (3/4 poles) [mm] 324/414 324/414 432/558 432/558 594/684 594/684 810/936
Weights
Fixed 3/4 poles [kg] 50/61 50/61 66/80 66/80 97/117 97/117 140/160
Withdrawable 3/4 poles (including fixed part) [kg] 50/61 50/61 66/80 66/80 147/165 147/165 210/240
(1) Without intentional delays.

SACE Emax Switch-disconnectors for
applications up to 1000V DC
ABB SACE has developed the SACE Emax/E MS range of switch-disconnectors for applications in
direct current up to 1000V in compliance with the international IEC 60947-3 Standard. These no-
automatic circuit-breakers are specially suitable for use as bus ties or main isolators in direct current
systems, such as in applications involving electric traction.
The range covers all installation needs up to 1000V DC /6300A.
They are available in fixed and withdrawable, three-pole and four-pole versions.
By connecting three breaking poles in series, it is possible to achieve a rated voltage of 750V DC,
while with four poles in series the limit rises to 1000V DC.
The switch-disconnectors of the SACE Emax/E MS range maintain the overall dimensions and fixing
points of the standard range circuit-breakers. They can be fitted with the various terminal kits and all
the accessories common to the SACE Emax range. They cannot, of course, be associated with the
electronic trip units, CSs and accessories for determining currents and for AC applications.
The withdrawable circuit-breakers should be used together with the special version fixed parts for
applications at 750/1000V DC.
E1B/E MS E2N/E MS E3H/E MS E4H/E MS* E6H/E MS*
Rated current (at 40 °C) Iu [A] 800 1250 1250 3200 5000
[A] 1250 1600 1600 4000 6300
[A] 2000 2000
[A] 2500
[A] 3200
Poles 3 4 3 4 3 4 3 4 3 4
Rated service voltage Ue [V] 750 750 750 750 750 750 750 750 750 750
Rated insulation voltage Ui [V] 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000
Rated impulse withstand voltage Uimp [kV] 12 12 12 12 12 12 12 12 12 12
Rated short-time withstand current Icw (1s) [kA] 20 20* 25 25* 40 40* 65 65 65 65
Rated making capacity Icm
750 V DC [kA] 42 42 52.5 52.5 105 105 143 143 143 143
1000 V DC [kA] 42 52.5 105 143 143
Note: the breaking capacity Icu, by means of external protection relay, with 500 ms maximum timing, is equal to the value of Icw (1s).
* The performances at 750 V are:
for E1B/E MS Icw=25kA
for E2N/E MS Icw=40kA
for E3H/E MS Icw=50kA

SACE Emax DC: Direct Current Applications
The main applications of direct current are:
1. Emergency supply or auxiliary services: the use of direct current is due to the need to employ a
back-up energy source which allows the supply of essential services such as protection services,
emergency lighting, alarm systems, hospital and industrial services, data-processing centres etc.,
using accumulator batteries
2. Electrical traction: the advantages offered by the use of dc motors in terms of regulation and of
single supply lines lead to the widespread use of direct current for railways, underground railways,
trams, lifts and public transport in general
3. Particular industrial installations: there are some electrolytic process plants and applications which
have a particular need for the use of electrical machinery
4. Navy, Alternative Energy Conversion, …

Direct Current Network Typology
Here below the typical distribution systems used in direct current are described:
Both Polarities Insulated from Earth
– Fault a: the fault, without negligible impedance, between the two polarities sets up a short-circuit
current to which both polarities contribute to the full voltage, according to which the breaking
capacity of the breaker must be selected.
– Fault b, c: the fault between the polarity and earth has no consequences from installation func-
tioning point of view.
One polarity connected to earth
– Fault a: the fault between the two polarities sets up a short-circuit current to which both polari-
ties contribute to the full voltage U, according to which the breaking capacity of the breaker is
selected.
– Fault b: the fault on the polarity not connected to earth sets up a current which involves the
over-current protection according to the resistance of the ground.
– Fault c: the fault between the polarity connected to earth and earth has no consequences from
the point of view of the function of the installation.
All the poles of the breaker necessary for protection must be connected in series on the non-earthed
polarity.

Direct Current Network Typology
Median Point connected to Earth
– Fault a: the fault between the two polarities sets up a short-circuit current to which both polari-
ties contribute to the full voltage U, according to which the breaking capacity of the breaker is
selected.
– Fault b: the fault between the polarity and earth sets up a short-circuit current less than that of
a fault between the two polarities, as it is supplied by a voltage equal to 0.5 U.
– Fault c: the fault in this case is analogous to the previous case, but concerns the negative polarity.
The breaker must be inserted on both polarities.

Circuit Breaker Selection
To correctly select the devices for the protection of a direct current network the following factors
must be considered:
• The type of network - earthing connection
• Rated Current
• Voltage Current
• The prospective short-circuit current at the point of installation
Here below the rating plate of an Emax DC air circuit-breaker for direct current application:
INCOMING POWER FROM UPPER TERMINALS
INCOMING POWER FROM BOTTOM TERMINALS

Protection trip units and trip curves
PR122/DC
Characteristics
The PR122/DC is the new electronic protection trip unit for the SACE Emax DC series suitable for
direct current installation wherein the basic protections are enough.
The PR122/DC offers the following protection functions:

• Overload (L);
• Selective short-circuit (S);
• Thermal memory for S and L (cable protection);
• Instantaneous short-circuit (I);
• Overtemperature protection (OT);
• Zone selectivity for S;
• Load Control (K).

Protection functions and setting values - PR122/DC
Function Trip Threshold Trip Time Poss. Relation Thermal Zone
threshold steps Time Step excl. t=f(I) memory selectivity
Overload I1= 0.4….1 x In 0.01 x In With current I = 3 x I1 3 s (1) – IEC60255-8 ■ –
protection t1= 3 s....102 s
Tolerance
(2)
Release between ± 10% If ≤ 6 x In
1.05 and 1.2 x I1 ± 20% If > 6 x In
Selective short- With current I > I2
circuit protection I2= 0.6….10 x In 0.1 x In t2= 0.05 s….0.35 s 0.01 s ■ t=k – ■
t2sel= 0.04 s…..0.2 s 0.01 s
Tolerance (2) ± 7% If ≤ 6 x In The better of the two figures:
± 10% If > 6 x In ± 10% or ± 40 ms
With current I = 10 x In
I2= 0.6….10 x In 0.1 x In t2= 0.05 s….0.35 s 0.01 s ■ t=k/I2 ■ –
Tolerance (2) ± 7% If ≤ 6 x In ± 15% If ≤ 6 x In
± 10% If > 6 x In ± 20% If > 6 x In
Instantaneous
short-circuit
protection I3= 1.5….10 x In 0.1 x In Instantaneous – ■ t=k – –
Tolerance (2) ± 10% ≤ 30 ms
OT Protection against
overtemperature May not be set – Instantaneous – – temp=k – –
(1) The minimum trip value is 1 s, regardless of the type of curve set (self-protection)
(2) These tolerances are valid in the following conditions:
- fully powered release by voltage module and/or auxiliary power supply (without start-up)
- trip time set ≥ 100 ms
The following tolerance values apply in all cases not covered by the above:
Trip threshold Trip time
L Release between 1.05 and 1.25 x I1 ± 20%

S ± 10% ± 20%
I ± 15% ≤ 60ms
Others ± 20%

PR122/DC
Power Supply
The PR122/DC trip unit does not normally require an auxiliary power supply being self-supplied from
the measurement module PR120/V always supplied as standard in PR122/DC (only for power supply,
no voltage and power based protection/measurements available in PR122/DC).
On request it is possible to supply the PR122/DC with a special version of measurements module
suitable for very low DC rated voltage 24/48V DC, called PR120/LV, typically railway and mine in-
stallations.
An external auxiliary power supply is however required in case of the PR120/LV module is present.
Power supply from Minimum Voltage Threshold

Measurement Module Enabling Unit PR122/DC
PR120/V 70 V
When an auxiliary power supply is present, refer to the below table for the overall electronic power
consumption.
PR122/DC PR120/D-M PR120/K

Auxiliary power supply 24 V DC ± 20% from PR122/DC from PR122/DC
(galvanically insulated)
Maximum ripple 5%
Inrush current @ 24V ~10 A for 5 ms
Rated power @ 24V ~3 W +1 W +1 W
The Emax DC is supplied as standard for incoming power from the bottom terminals: PR120/V
- PR120/LV internal connection on bottom terminals – “U rear connection kit” mounted on upper
terminals.
Refer to Ordering Codes Section for incoming power from the upper terminals.
1 Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Functions L-S-I
t=k
Functions L-S-I
I2t = k

PR123/DC
Characteristics
The PR123/DC is the new electronic protection trip unit for the SACE Emax DC series; the complete
range of protection functions together with the wide combination of thresholds and trip times offered
make it suitable for protecting a wide range of direct current installation.
The PR123/DC offers the following protection functions:

• Overload (L);
• Selective short-circuit (S);
• Thermal memory for L and S (cable protection);
• Instantaneous short-circuit (I);
• Earth fault with adjustable delay (G);
• Poles unbalance (U);
• Overtemperature protection (OT);
• Load control (K);
• Undervoltage (UV);
• Overvoltage (OV);
• Reverse power (RP);
• Dual setting;
• Zone selectivity for S, G;
• Start-up thresholds for protection S and I.

Protection functions and setting values - PR123
Function Trip Threshold Trip Time Can be Relation Thermal Zone
threshold steps Time Step excluded t=f(I) memory selectivity
Overload With current I = 3xI1
protection I1= 0.4….1 x In 0.01 x In t1= 3 s....102 s 3 s (1) – IEC60255-8 ■ –
Tolerance (2) Release between ± 10% If ≤ 6 x In
1.05 and 1.2 x I1 ± 20% If > 6 x In
I1= 0.4….1 x In 0.01 x In With current I = 3xI1; t1= 3 s....144 s 3s – t=k(α)
Tolerance Release between ± 20% If > 5 x I1 α = 0.2-1-2
1.05 ... 1.2 x I1 ± 30% 2xI1≤ If ≤ 5 x I1
Selective short-circuit With current I > I2
protection I2= 0.6….10 x In 0.1 x In t2= 0.05 s….0.35 s 0.01 s ■ t=k – ■
t2sel= 0.04 s…..0.2 s 0.01 s
± 10% If > 6 x In ± 10% or ± 40 ms
I2= 0.6….10 x In 0.1 x In With current I = 10xIn; t2= 0.05 s…0.35 s 0.01 s ■ t=k/I2 ■ –
Tolerance (2) ± 7% If ≤ 6 x In ± 15% If ≤ 6 x In
± 10% If > 6 x In ± 20% If > 6 x In
Selective short-circuit With current I > I2
protection I2= 0.6….10 x In 0.1 x In t2= 0.05 s….0.35 s 0.01 s ■ t=k – ■
± 10% If > 6 x In ± 10% or ± 40 ms
Instantaneous
short-circuit
protection I3= 1.5….10 x In 0.1 x In Instantaneous – ■ t=k – –
Tolerance (2) ± 10% ≤ 30 ms
Earth fault With current I > I4
protection I4= 0.2….1 x In 0.02 x In t4= 0.1 s…..1 s 0.05 s ■ t=k – ■
t4sel= 0.04 s…..0.2 s 0.01 s
Tolerance (2)
The better of the two figures:
± 7% ± 10% or ± 40 ms
I4= 0.2….1 x In 0.02 x In t4= 0.1 s…..1 s (with I=4xI4) 0.05 s ■ t=k/I2 – –
Tolerance (2) ± 7% ± 15%
U Phase unbalance I6= 5%….90% 5% t6= 0.5 s…..60 s 0.5 s ■ t=k – –
protection The better of the two figures:
Tolerance (2) ± 10% ± 20% or ± 100 ms
Protection against
OT
overtemperature cannot be set – Instantaneous – – temp=k – –
Undervoltage I8= 0.5….0.95 x Un 0.01 x In With current U < U8; t8= 0.1 s….5 s 0.1 s ■ t=k – –
UV protection The better of the two figures:
Tolerance (2) ± 5% ± 20% or ± 40 ms
Overvoltage I9= 1.05….1.2 x Un 0.01 x In With current U > U9; t9= 0.1 s….5 s 0.1 s ■ t=k – –
OV protection The better of the two figures:
Tolerance (2)
± 5% ± 20% or ± 40 ms
RP Reverse With current P < P11
power P11= -0.3….-0.1 x Pn 0.02 Pn t11= 0.5 s…..25 s 0.1 s ■ t=k – –
protection The better of the two figures:
Tolerance (2) ± 10% ± 10% or ± 100 ms
(1) The minimum trip value is 1 s, regardless of the type of curve set (self-protection)
(2) These tolerances hold in the following conditions:
- fully powered release by voltage module and/or auxiliary power supply (without start-up)
- trip time set ≥ 100 ms
The following tolerance values apply in all cases not covered by the above:
Trip threshold Trip time
L Release between 1.05 and 1.25 x I1 ± 20%

S ± 10% ± 20%
I ± 15% ≤ 60ms
G ± 15% ± 20%
Others ± 20%

PR123/DC
Power Supply
The PR123/DC trip unit does not normally require an auxiliary power supply being self-supplied from
the measurement module PR120/V always supplied as standard in PR123/DC.
On request it is possible to supply the PR123/DC with a special version of measurements module
suitable for very low DC rated voltage 24/48V DC, called PR120/LV, typically railway and mine in-
stallations.
An external auxiliary power supply is however required in case of the PR120/LV module is present.
Power supply from Minimum Voltage Threshold

Measurement Module Enabling Unit PR123/DC
PR120/V 70 V
When an auxiliary power supply is present, refer to the below table for the overall electronic power
consumption.
PR123/DC PR120/D-M PR120/K

Auxiliary power supply 24 V DC ± 20% from PR122/DC from PR122/DC
(galvanically insulated)
Maximum ripple 5%
Inrush current @ 24V ~10 A for 5 ms
Rated power @ 24V ~3 W +1 W +1 W
The Emax DC is supplied as standard for incoming power from the bottom terminals: PR120/V
- PR120/LV internal connection on bottom terminals – “U rear connection kit” mounted on upper
terminals.
Refer to Ordering Codes Section for incoming power from the upper terminals.

Functions L-S-I
t=k
Functions L-S-I
I2t = k

PR123/DC
Function G
k
t=
I2
t=k
1SDC200112F0001
Function U
1SDC200122F0001

Function RP
RP
1SDC200126F0001
Function UV
UV
1SDC200123F0001

PR123/DC
Function OV
OV
1SDC200124F0001

Override Protection
The automatic circuit-breakers of SACE Emax DC range are supplied of an internal back-up protection
called Override Protection made by the Module PR120/DC always supplied with the PR122/DC
and PR123/DC electronic trip units.
The Override Protection ensures the protection of the electrical plant against instantaneous short-
circuit in case of any loss of power supply of the protection unit PR122/DC and PR123/DC.
The Override protection threshold depends on the circuit breaker size; as standard neither connec-
tions nor settings are in user’ care.

PR123/DC
Optional Modules for Electronic Trip units

The electronic trip units PR122/DC and PR123/DC can be equipped with the same internal optional
modules already available on the electronic devices PR122/P and PR123/P for alternative current
application.
Code Internal Description PR123/DC

1SDA058255R1 PR120/K Internal signalling module ■
(4 output with independent terminals)
1SDA058256R1 PR120/K Internal signalling module ■
(4 output + 1 input with a common terminal)
1SDA058254R1 PR120/D-M Modbus RTU communication module ■
1SDA058252R1(1) PR120/LV Measurements module ■
1SDA065223R1(2) PR120/LV Measurements module - low voltage ■

(3)
PR120/DC Override protection module ■
(1) PR120/V Measurements Module always supplied with the trip units PR123/DC and PR122/DC
(2) Extracode to be specified with the circuit-breaker code to have the low voltage measuring module PR120/LV
(3) Not to be specified, always supplied with the electronic trip unit
Code External Description PR123/DC

1SDA058258R1 PR030/B Power supply unit ■
1SDA058259R1 BT030 External communication wireless unit ■
1SDA063143R1 HMI030 Interface from front of panel ■
1SDA048964R1 PR010/T External test unit ■
1SDA059146R1 PR021/K External signalling unit ■
1SDA052927R1 ATS010 Automatic transfer switch ■
1SDA060198R1 EP010 ABB Fieldbus plug ■

Measurements
PR122/DC
The following measurements are available
• Current;
• Instantaneous current value over a given time interval;
• Maintenance: number of operations, percentage of contact wears, opening data storage (latest
20 trips and 80 events);
• The protection records the historical data of the maximum current read.
PR123/DC
• Current;
• Maintenance: number of operations, percentage of contact wears, opening data storage (latest
20 trips and 80 events);
• Voltage;
• Instantaneous current/voltage value over a given time interval (data logger);
• Power;
• Energy;
• The protection records the historical data of the maximum current read, the maximum and minimum
voltage, the total maximum and mean value of power.

Measurements
Measurement Functions
The measurements available on electronic trip units PR122/DC and PR123/DC fitted by the Modbus
Communication module PR120/D-M and the protocol converter for Profibus and Devicenet FieldBus
EP010-FBP are listened on the following table.
PR122/DC PR123/DC PR122/DC-PR123/DC

+ PR120/D-M + PR120/D-M + PR120/D-M
and EP010
Communication functions
Protocol Modbus RTU Modbus RTU FBP
Physical layer RS-485 RS-485 Profibus-DP or
DeviceNet cable
Maximum baudrate 19200 bps 19200 bps 115 kbps
Measuring functions
Currents ■ ■ ■
Ground current ■ ■ ■
Voltage ■ on demand (1)
Power ■ on demand (1)
Energy ■ on demand (1)
Signalling from functions

LED: auxiliary power supply, warning, alarm ■ ■ ■
Temperature ■ ■ ■
Indication for L, S, I, G and other protection ■ ■ ■
Available data
Circuit-breaker status (open, closed) ■ ■ ■
Circuit-breaker position (racked-in, racked-out) ■ ■ ■
Mode (local, remote) ■ ■ ■
Protection parameters set ■ ■ ■
Load control parameters ■ ■ ■
Alarms
Protection L ■ ■ ■
Protection S ■ ■ ■
Protection I ■ ■ ■
Protection G ■ ■
Fault release mechanism failure ■ ■ ■
Undervoltage, overvoltage (timing and trip) protection ■ on demand (1)
Reverse power protection (timing and trip) ■ on demand (1)
Maintenance
Total number of operations ■ ■ ■
Total number of trips ■ ■ ■
Number of trip tests ■ ■ ■
Number of manual operations ■ ■ ■
Number of separate trips for each protection function ■ ■ ■
Contact wear (%) ■ ■ ■
Record data of last trip ■ ■ ■
Operating mechanisms
Circuit-breaker open/close ■ ■ ■
Reset alarms ■ ■ ■
Setting of curves and protection thresholds ■ ■ ■
Synchronize system time ■ ■ ■
Events
Status changes in circuit-breaker, protections and all alarms ■ ■ ■
(1) please ask ABB for further details

Accessories
Electrical and Mechanical Accessories
Accessories
The SACE Emax DC family can be fitted by the same electrical and mechanical accessories already
available on the standard alternative current family.
The ranges Automatic circuit-breakers Switch-disconnectors

Isolating Earthing Earthing
Circuit-breakers with Switch-disconnectors truck switch truck
full-size neutral for applications up to 1150V AC (CS) with (MT)
making
Circuit-breakers for Switch-disconnectors capacity
applications for applications up to 1000V DC (MPT)
up to 1150V AC
Circuit-breaker version Fixed Withdrawable Fixed Withdrawable Withdrawable Withdrawable Withdrawable
1a) Shunt opening/closing release (YO/YC)
and second opening release (YO2) ■ ■ ■ ■ ■ (YC)
1b) SOR test unit ■ ■ ■ ■
2a) Undervoltage release (YU) ■ ■ ■ ■
2b) Time-delay device for undervoltage release (D) ■ ■ ■ ■
3) Geared motor for the automatic charging
of the closing springs (M) ■ ■ ■ ■ ■
4a) Electrical signalling of electronic releases tripped ■ ■
4b) Electrical signalling of electronic releases tripped
with remote reset command ■ ■
5a) Electrical signalling of circuit-breaker open/closed (1) ■ ■ ■ ■ ■
5b) External supplementary electrical signalling
of circuit-breaker open/closed ■ ■ ■ ■ ■
5c) Electrical signalling of circuit-breaker racked-in/
test isolated/racked-out ■ ■ ■ ■ ■
5d) Contact signalling closing springs charged ■ ■ ■ ■ ■
5e) Contact signalling undervoltage release
de-energized (C. Aux YU) ■ ■ ■ ■
6a) Current transformer for neutral conductor
outside circuit-breaker ■ ■
6b) Homopolar toroid for the main power supply earthing
conductor (star center of the transformer) ■ ■
6c) Homopolar toroid for residual current protection ■ ■
7) Mechanical operation counter ■ ■ ■ ■ ■
8a) Lock in open position: key ■ ■ ■ ■ ■
8b) Lock in open position: padlocks ■ ■ ■ ■ ■
8c) Circuit-breaker lock in racked-in/racked-out/
test isolated position ■ ■ ■ ■ ■
8d) Accessories for lock in racked-out/test isolated position ■ ■ ■ ■ ■
8e) Accessory for shutter padlock device ■ ■ ■ ■ ■
8f) Mechanical lock for compartment door ■ ■ ■ ■ ■
9a) Protection for opening and closing pushbuttons ■ ■ ■ ■ ■
9b) IP54 door protection ■ ■ ■ ■ ■
10) Interlock between circuit-breakers (2) ■ ■ ■ ■
11) Automatic transfer switch - ATS010 (3) ■ ■ ■ ■
CAPTION
(1) For automatic circuit-breakers, four auxiliary contacts to electrically signal circuit-breaker
open/closed are included in the supply as standard.
■ Accessory on request for fixed circuit-breaker or moving part
(2) Incompatible with the E6/f versions with full-size neutral
■ Accessory on request for fixed part (3) Incompatible with the range of circuit-breakers for applications up to 1150V AC
■ Accessory on request for moving part
For Emax DC circuit-breakers accessories please refer to the same accessories codes of standard Emax AC circuit-breakers.

Overall dimensions
Fixed circuit-breaker
Basic version
with rear terminals INCOMING POWER FROM UPPER TERMINALS 6
4 POLES E2 - E4 E3 - E6
3 POLES
3 POLES
4 POLES
INCOMING POWER FROM BOTTOM TERMINALS 7
Caption
1 Inside edge of compartment

door
2 Segregation (when provided)
3 M10 mounting holes for
circuit-breakers (use M10 E2 III E2 IV
screws) View A View A
397
4 1xM12 screw (E1, E2, E3)
or 2xM12 screws (E4, E6) Iu=1250A 90 90 90 Iu=1250A
for earthing (included in Iu=1600A 145 100 Iu=1600A
the supply) 65
5 Insulating wall or
insulated metal wall
148
6 In case of incoming power 98 78
from UPPER terminals –
PR120/V internal connection
on upper terminals and 252
U rear connection kits on 242 177
bottom terminals M10

45
7 In case of incoming power 49
from BOTTOM terminals – Max. 40
PR120/V internal connection 330

on bottom terminals and U
rear connection kits on upper
terminals Iu=800A 100 145 Iu=800A
Iu=1000A 65
Iu=1000A
148
A B C D 98
78
E2 386 296 148 148 90 90 90
E3 530 404 202 202
E4 746 566 238 328
E6 1034 782 328 454

577
E4 III 180 180 325

View A
150 325 Iu=2500A 280
Iu=3200A
65 65
45
188
188
98 98
78 78
180 180
Iu=1600A
150 Iu=2000A
252
242 177
60
M10 10
45 10 10
49
50
Max. 40 98
78
510
757
E4 IV 180 180 180

Iu=2500A 325
View A Iu=3200A
280 325 280
65 65
45
188 188
98 98
78 78
180 180
Iu=1600A
252
242 177
150 Iu=2000A
60
M10 10
45 10 10
49
Max. 40 50
98
78
690
211
415
95
126 126
Iu=2000A
E3 III Iu=2500A 114
View A 96
168
148
98 78 98
78
126 126
177
Iu=800A
96
242 Iu=1000A
12
252 10
Iu=1250A
M10 10
12 12
Iu=1600A
49
50
Max. 40 98
78
348

Overall dimensions
Fixed circuit-breaker
Basic version
with rear terminals
541
Iu=2000A 126 126 126

E3 IV 126 126 126
Iu=2500A
View A 114 211
96 95
95
168 148
98 78 98 78
96
12
252
177 10 10 Iu=800A
242 Iu=1000A
M10 12 12 Iu=1250A
63
49
Iu=1600A
50
Max. 40 98
78
474
793
252 252
E6 III 410
View A
222 79,5 85
56
208
98 222
78 56 56
70
12
10 10
177 12 12
252
242
M10 50
98
78
49
Max. 40
63
726
1045
252 252 252

E6 IV
View A 182 410
56 85 85
208
222
98 56 70 56
78
12
10 10
177
12 12
252
242
M10 50
98
78
49
Max. 40
63
978

Compartment dimensions
A B
E2 400 490
E3 500 630
E4 700 880
E6 1000 1260
Depth
3 POLES
4 POLES
Through-holes for flexible cables for mechanical Drilling of compartment door

interlocks
N° 2 holes for IP54

protection cover

Overall dimensions
Withdrawable circuit-breaker
Basic version with

rear terminals INCOMING POWER FROM UPPER TERMINALS 6
4 POLES
E2-E4 E3-E6
3 POLES
3 POLES
4 POLES
INCOMING POWER FROM BOTTOM TERMINALS 7
Caption
1 Inside edge of compartment

door
2 Segregation (when provided)
3 M10 mounting holes for E2 III E2 IV
circuit-breakers (use M10 View A View A
screws) 417
4 1xM12 screw (E1, E2, E3) 327 145
or 2xM12 screws (E4, E6) 100 100
for earthing (included in 90 90 90 90 90
the supply)
Iu=1250A 103
5 Insulating wall or 103
53 33 Iu=1600A 53 33
insulated metal wall
129 174
6 In case of incoming power
from UPPER terminals –
0
0
PR120/V internal connection 393,5 380

Ø1
Ø1
on upper terminals and 380

225 393,5 45 225
240
U rear connection kits on 240
bottom terminals
70 49
7 In case of incoming power 70 240
from BOTTOM terminals –
PR120/V internal connection 100 175 Iu=1250A
138 220 Iu=1600A
on bottom terminals and U
rear connection kits on upper 145 145
terminals Iu=800A 65 100
100
Iu=1000A
103 103
53 33 53 33
A B C D 65 90 90 90
90 90 Iu=800A
E2 414 324 162 162 Iu=1000A
E3 558 432 216 216 60 60
10 10
E4 774 594 252 342
10 10 10 10
E6 1062 810 342 468 53 33 50 53 33 50

597
180 180
E4 III
325
View A 325
280
Iu=2500A 280
Iu=3200A
65 65
143 143
103
53 33 53 33
528 180 180

Ø10
33 10 10
40 45
393,5
7 10 10 10 10 Iu=1600A
380 84 400
530
53 50
Iu=2000A
33
122
120
E4 IV 777
View A 180 180 180
325 Iu=2500A 325

280
Iu=3200A
280
65 65
143 143
103
53 53 33
33
708
0 180 180 180
Ø1 45
33
10 10
393,5 40 700
7
10 10 10 10
Iu=1600A
380 580
84 Iu=2000A
53 33 50
122
120
435
126 126
211 211
E3 III 158 114
View A Iu=2000A
95 95
Iu=2500A
123 103
53 53
33 33
183
0
126 126
Ø1
33
393,5 40
7 240 12
380 225 10 10
84 183
12 12 Iu=800A
122 Iu=1000A
63 33 50
49 70 Iu=1250A
Iu=1600A
6 200
400

Overall dimensions
Withdrawable circuit-breaker
Basic version with

rear terminals
561
E3IV 211
View A 95 Iu=2000A
158
Iu=2500A
211
95 114
123
53
33
103
126 126 126 63
246 33
10
Ø
126 126 126
33
393,5
380
40 7 225 Iu=800A
84 63 240 12 Iu=1000A
10 10 Iu=1250A
122 12 12
Iu=1600A
49 70
53 33 50
6 325
370
490
813
463
E6 III
410
View A
252 252 85
163
53 33
222
744 182
Ø10
33 12
393,5 40 10 10
380 7
84 12 12
750
53 50
33
122
63
620
1065
463
E6 IV
View A 410 410
252 252 252 85
163
53 222
33
182
12
10 10
33
393,5
40 12 12
380 7
84 53 50
33
122
63
866

Compartment dimensions
A B
E2 400 490
E3 500 630
E4 700 880
E6 1000 1260
Depth
3 POLES
4 POLES
Through-holes for flexible cables for mechanical Drilling of compartment door

interlocks
N° 2 holes for IP54

protection cover

Overall dimensions
Circuit-breaker accessories
Mechanical
compartment
door lock
Holes in compartment door Minimum distance between circuit-breakers and switchboard wall
Fixed version Withdrawable version
A
3 POLES 4 POLES
E2 180 180
E3 234 234
E4 270 360
E6 360 486

Circuit diagrams
Reading information
Warning
Before installing the circuit-breaker, carefully read note F on the circuit diagrams.
Operating status shown

The circuit diagram is for the following conditions:
- withdrawable circuit-breaker, open and racked-in
- circuits de-energised
- releases not tripped
- motor operating mechanism with springs discharged.
Versions
Though the diagram shows a circuit-breaker in withdrawable version, it can be applied to a fixed version circuit-breaker
as well.
Fixed version
The control circuits are fitted between terminals XV (connector X is not supplied).
With this version, the applications indicated in figures 31 and 32 cannot be provided.
Withdrawable version
The control circuits are fitted between the poles of connector X (terminal box XV is not supplied).
Version with PR122/DC electronic trip unit
Version with PR123/DC electronic trip unit
Caption
= Circuit diagram figure number
* = See note indicated by letter
A1 = Circuit-breaker accessories
A3 = Accessories applied to the fixed part of the circuit-breaker (for withdrawable version only)
A4 = Example switchgear and connections for control and signalling, outside the circuit-breaker
D = Electronic time-delay device of the undervoltage release, outside the circuit-breaker
F1 = Delayed-trip fuse
K51 = PR122/DC, PR123/DC electronic trip unit with the following protection functions:
- L overload protection with inverse long time-delay trip - setting I1
- S short-circuit protection with inverse or definite short time-delay trip - setting I2
- I short-circuit protection with instantaneous time-delay trip - setting I3
- G earth fault protection with inverse short time-delay trip - setting I4
K51/1...8 = Contacts of the PR021/K signalling unit
K51/GZin = Zone selectivity: input for protection G (only with Uaux. and PR123/DC trip unit)
K51/GZout = Zone selectivity: output for protection G (only with Uaux. and PR123/DC trip unit)
K51/IN1 = Digital programmable input (available only with Uaux and PR122/DC or PR123/DC trip unit with indicator
module PR120/K)
K51/P1...P4 = Programmable electrical signalling (available only with Uaux and PR122/DC or PR123/DC trip unit with
indicator module PR120/K)
K51/SZin = Zone selectivity: input for protection S (only with Uaux. And PR123/DC trip unit)
K51/SZout = Zone selectivity: output for protection S (only with Uaux. And PR123/DC trip unit)
K51/YC = Closing control from PR122/DC or PR123/DC electronic trip unit with communication module PR120/D-M
K51/YO = Opening control from PR122/DC or PR123/DC electronic trip unit with communication module PR120/D-M
M = Motor for charging the closing springs
Q = Circuit-breaker
Q/1...27 = Circuit-breaker auxiliary contacts
S33M/1...3 = Limit contacts for spring-charging motor
S43 = Switch for setting remote/local control
S51 = Contact for electrical signalling of circuit-breaker open due to tripping of the overcurrent release. The
circuit-breaker may be closed only after pressing the reset pushbutton, or after energizing the coil for
electrical reset (if available).
S75E/1...4 = Contacts for electrical signalling of circuit-breaker in racked-out position (only with withdrawable circuit-
breakers)
S75I/1...5 = Contacts for electrical signalling of circuit-breaker in racked-in position (only with withdrawable circuit-
breakers)
S75T/1..4 = Contacts for electrical signalling of circuit-breaker in test isolated position (only with withdrawable circuit-
breakers)
SC = Pushbutton or contact for closing the circuit-breaker
SO = Pushbutton or contact for opening the circuit-breaker
SO1 = Pushbutton or contact for opening the circuit-breaker with delayed trip
SO2 = Pushbutton or contact for opening the circuit-breaker with instantaneous trip
SR = Pushbutton or contact for electrical circuit-breaker reset

Circuit diagrams
Reading information
W1 = Serial interface with control system (external bus): EIA RS485 interface (see note E)
W2 = Serial interface with the accessories of PR122/DC and PR123/DC trip units (internal bus)
X = Delivery connector for auxiliary circuits of withdrawable version circuit-breaker
X1...X7 = Connectors for the accessories of the circuit-breaker
XF = Delivery terminal box for the position contacts of the withdrawable circuit-breaker (located on the fixed
part of the circuit-breaker)
XK1 = Connector for power circuits of PR122/DC and PR123/DC trip units
XK2 - XK3 = Connectors for auxiliary circuits of PR122/DC and PR123/DC trip units
XK4 = Connector signalling open/closet contact
XK5 = Connector for PR120/V module
XO = Connector for YO1 release
XV = Delivery terminal box for the auxiliary circuits of the fixed circuit-breaker
YC = Shunt closing release
YO = Shunt opening release
YO1 = Overcurrent shunt opening release
YO2 = Second shunt opening release (see note Q)
YR = Coil to electrically reset the circuit-breaker
YU = Undervoltage release (see notes B and Q)
Description of figures
Fig. 1 = Motor circuit to charge the closing springs.
Fig. 2 = Circuit of shunt closing release.
Fig. 4 = Shunt opening release.
Fig. 6 = Instantaneous undervoltage release (see notes B and Q).
Fig. 7 = Undervoltage release with electronic time-delay device, outside the circuit-breaker (see notes B and Q)
Fig. 8 = Second shunt opening release (see note Q).
Fig. 11 = Contact for electrical signalling of springs charged.
Fig. 12 = Contact for electrical signalling of undervoltage release energized (see notes B and S).
Fig. 13 = Contact for electrical signalling of circuit-breaker open due to tripping of the overcurrent release. The
circuit-breaker may be closed only after pressing the reset pushbutton.
Fig. 14 = Contact for electrical signalling of circuit-breaker open due to tripping of the overcurrent release and elec-
trical reset coil. The circuit-breaker may be closed only after pressing the reset pushbutton or energizing
the coil.
Fig. 21 = First set of circuit-breaker auxiliary contacts.
Fig. 22 = Second set of circuit-breaker auxiliary contacts (see note V).
Fig. 23 = Third set of supplementary auxiliary contacts outside the circuit-breaker.
Fig. 31 = First set of contacts for electrical signalling of circuit-breaker in racked-in, test isolated, racked-out position.
Fig. 32 = Second set of contacts for electrical signalling of circuit-breaker in racked-in, test isolated, racked-out
position.
Fig. 42 = Auxiliary circuits of PR122/DC and PR123/DC trip units (see notes F, M and V).
Fig. 45 = Circuits of the communication module PR120/D-M of the PR122/DC and PR123/DC trip units (optional,
see note E).
Fig. 46 = Circuits of the indicator module PR120/K of the PR122/DC and PR123/DC trip units - connection 1
(optional; see note V).
Fig. 47 = Circuits of the indicator module PR120/K of the PR122/DC and PR123/DC trip units - connection 2
(optional; see note V).
Fig. 62 = Circuits of the PR021/K signalling module (outside the circuit-breaker)
Incompatibilities
The circuits indicated in the following figures cannot be supplied simultaneously on the same circuit-breaker:
6-7-8
13 - 14
22 - 46 - 47

Notes
A) The circuit-breaker is only fitted with the accessories specified in the ABB SACE order acknowledgement. Consult
this catalogue for information on how to make out an order.
B) The undervoltage release is supplied for operation using a power supply branched on the supply side of the circuit-
breaker or from an independent source. The circuit-breaker can only close when the release is energized (there is
a mechanical lock on closing).
If the same power supply is used for the closing and undervoltage releases and the circuit-breaker is required to
close automatically when the auxiliary power supply comes back on, a 30 ms delay must be introduced between
the undervoltage release accept signal and the energizing of the closing release. This may be achieved using an
external circuit comprising a permanent make contact, the contact shown in fig. 12 and a time-delay relay.
E) MODBUS map is available in the RE1134001 document
F) The auxiliary voltage Uaux allows actuation of all operations of the PR122/DC and PR123/DC trip units. Having
requested a Uaux insulated from earth, one must use “galvanically separated converters” in compliance with IEC
60950 (UL 1950) or equivalent standards that ensure a common mode current or leakage current (see IEC 478/1,
CEI 22/3) not greater than 3.5 mA, IEC 60364-41 and CEI 64-8.
N) With PR122/DC and PR123/DC trip units, the connections to the zone selectivity inputs and outputs must be made
with a two-pole shielded and stranded cable (see user manual), no more than 300 m long. The shield must be
earthed on the selectivity input side.
P) With PR122/DC and PR123/DC trip units with communication module PR120/D-M, the power supply for coils YO
and YC must not be taken from the main power supply. The coils can be controlled directly from contacts K51/YO
and K51/ YC with maximum voltages of 110-120 V DC and 240-250 V AC.
Q) The second opening release may be installed as an alternative to the undervoltage release.
S) Also available in the version with normally-closed contact
V) If fig. 22 is present (second set of auxiliary contacts) simultaneously as PR122/DC or PR123/DC release, the con-
tacts for the zone selectivity in fig. 42 (K51/Zin, K51/Zout, K51/Gzin and K51/Gzout) are not wired. In addition, the
indicator module PR120/K in figures 46 and 47 cannot be supplied.

Circuit diagrams
Circuit diagram symbols (IEC 60617 and CEI 3-14 ... 3-26
Standards)
Shield Terminal Position switch (limit switch)

(may be drawn change-over break before
in any shape) make contact
Delay Plug and socket Circuit-breaker-disconnector

(male and female) with automatic release
Mechanical connection Motor Switch-disconnector

(link) (general symbol) (on-load isolating switch)
Manually operated Current transformer Operating device

control (general case) (general symbol)
Operated by turning Voltage transformer Instantaneous

overcurrent or rate-of-rise
relay
Operated by pushing Winding of three-phase Overcurrent relay with

transformer, connection adjustable short time-lag
star characteritic
Equipotentiality Make contact Overcurrent relay with inverse

short time-lag characteritic
Converter with galvanic Break contact Overcurrent relay

separator with inverse long time-lag
characteritic
Conductors in a screened Change-over break before Earth fault overcurrent relay

cable (i.e., 3 conductors make contact with inverse short time-lag
shown) characteritic
Twisted conductors (i.e., 3 Position switch (limit switch), Fuse

conductors shown) make contact (general symbol)
Connection of conductors Position switch (limit switch), Current sensing

break contact element

Circuit diagrams
Circuit-breakers
Operating status
A1 C1 B1 A1 C1 D1 B1
K51 K51
Q Q
>
XK10 XK10
A1I 1 A1I 1
>> >>
2 2
A1E XO A1E XO
>> 1 >> 1
>>
> >>>
1
1
Y01 Y01
XO XO
2
2
>> 2 >> 2
PR122/DC PR122/DC
XK11 XK11
B1I 1 B1I 2
2 1
B1E B1E
PR123/DC PR123/DC
a1 c1 b1 a1 c1 d1 b1
Three-pole circuit-breaker with PR122/DC or PR123/DC electronic trip Four-pole circuit-breaker with PR122/DC or PR123/DC electronic trip
units units
A1 A2 C1 C2 D1 D2 B1 B2
K51
Q
>
>>
XK10 XO
A1I 1 >> 1
2 >>>
A1E
1
Y01
XO
2
>> 2
XK10
A2I 3
4
A2E
PR122/DC PR122/DC
XK11
B1I 1
B1E 2
XK11
B2I 3
4
B2E
PR123/DC
PR123/DC
a1 a2 c1 c2 d1 d2 b1 b2
Three-pole circuit-breaker with PR122/DC or PR123/DC electronic Four-pole circuit-breaker with PR122/DC or PR123/DC electronic trip
trip units units

Circuit diagrams
Circuit-breakers
Motor operating mechanism, opening, closing and undervoltage

trip units
Signalling contacts

Signalling contacts

Circuit diagrams
Circuit-breakers
Auxiliary circuits of the PR122/DC and PR123/DC trip units
CAPTION: see note F.
PR122/DC
PR123/DC
Communication module PR120/D-M
PR122/DC
PR123/DC

Signalling module PR120/K
(+)
(+)
(+)
PR122/DC PR122/DC
PR123/DC PR123/DC
(-)
(-)
(-)
PR021/K Signalling unit
PR122/DC
PR123/DC
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected] 1

Ordering codes
SACE Emax DC automatic circuit-breakers for application
up to 1000 V DC
PR122/DC PR123/DC
1SDA......R1 1SDA......R1
3 Poles 4 Poles 3 Poles 4 Poles

E2 08 Iu (40 °C) = 800 A
VR = Vertical rear terminals
Fixed (F)
B 064580 064585 064668 064673

E2 10 Iu (40 °C) = 1000 A
Fixed (F)
B 064581 064586 064669 064674

E2 12 Iu (40 °C) = 1250 A
Fixed (F) B 064582 064587 064670 064675

E2 16 Iu (40 °C) = 1600 A
Fixed (F) B 064583 064588 064671 064676
N 064584 064589 064672 064677

E3 08 Iu (40 °C) = 800 A
Fixed (F)
N 064600 064609 064688 064697

E3 10 Iu (40 °C) = 1000 A
Fixed (F)
N 064601 064610 064689 064698

E3 12 Iu (40 °C) = 1250 A
Fixed (F)
N 064602 064611 064690 064699

E3 16 Iu (40 °C) = 1600 A
Fixed (F)
N 064603 064612 064691 064700
H 064606 064615 064694 064703

E3 20 Iu (40 °C) = 2000 A
Fixed (F)
N 064604 064613 064692 064701
H 064607 064616 064695 064704

E3 25 Iu (40 °C) = 2500 A
Fixed (F)
N 064605 064614 064693 064702
H 064608 064617 064696 064705

PR122/DC PR123/DC
1SDA......R1 1SDA......R1

E4 16 Iu (40 °C) = 1600 A
Fixed (F)
S 064636 064641 064724 064729

E4 20 Iu (40 °C) = 2000 A
Fixed (F)
S 064637 064642 064725 064730

E4 25 Iu (40 °C) = 2500 A
Fixed (F) S 064638 064643 064726 064731

E4 32 Iu (40 °C) = 3200 A
Fixed (F) S 064639 064644 064727 064732
H 064640 064645 064728 064733

E6 32 Iu (40 °C) = 3200 A
Fixed (F)
H 064656 064659 064744 064747

E6 40 Iu (40 °C) = 4000 A
Fixed (F)
H 064657 064660 064745 064748

E6 50 Iu (40 °C) = 5000 A
Fixed (F)
H 064658 064661 064746 064749

1SDA......R1
Extracode
PR120/LV Low Voltage measuring module 24-48 V DC 065223*
PR120/V - PR120/LV Internal connection on upper terminals 058251**
* extracode to be specified with the circuit breaker code to have the low voltage measuring module PR120/LV
** The Emax DC is supplied ad standard for incoming power from the bottom terminals (PR120/V internal connection on bottom terminals – “U rear
connection kit” mounted on upper terminals).
In case of incoming power from the upper terminals an extracode must be specified: 1SDA058251R1 (PR120/V internal connection on upper
terminals – “U rear connection kit” mounted on bottom terminals).

Ordering codes
SACE Emax DC automatic circuit-breakers for application
up to 1000 V DC
PR122/DC PR123/DC
1SDA......R1 1SDA......R1

E2 08 Iu (40 °C) = 800 A
Withdrawable (W) - MP
B 064590 064595 064678 064683

E2 10 Iu (40 °C) = 1000 A
B 064591 064596 064679 064684

E2 12 Iu (40 °C) = 1250 A
Withdrawable (W) - MP B 064592 064597 064680 064685

E2 16 Iu (40 °C) = 1600 A
Withdrawable (W) - MP B 064593 064598 064681 064686
N 064594 064599 064682 064687

E3 08 Iu (40 °C) = 800 A
N 064618 064627 064706 064715

E3 10 Iu (40 °C) = 1000 A
N 064619 064628 064707 064716

E3 12 Iu (40 °C) = 1250 A
N 064620 064629 064708 064717

E3 16 Iu (40 °C) = 1600 A
N 064621 064630 064709 064718
H 064624 064633 064712 064721

E3 20 Iu (40 °C) = 2000 A
N 064622 064631 064710 064719
H 064625 064634 064713 064722

E3 25 Iu (40 °C) = 2500 A
N 064623 064632 064711 064720
H 064626 064635 064714 064723

PR122/DC PR123/DC
1SDA......R1 1SDA......R1

E4 16 Iu (40 °C) = 1600 A
S 064646 064651 064734 064739

E4 20 Iu (40 °C) = 2000 A
S 064647 064652 064735 064740

E4 25 Iu (40 °C) = 2500 A
Withdrawable (W) - MP S 064648 064653 064736 064741

E4 32 Iu (40 °C) = 3200 A
Withdrawable (W) - MP S 064649 064654 064737 064742
H 064650 064655 064738 064743

E6 32 Iu (40 °C) = 3200 A
H 064662 064665 064750 064753

E6 40 Iu (40 °C) = 4000 A
H 064663 064666 064751 064754

E6 50 Iu (40 °C) = 5000 A
H 064664 064667 064752 064755

1SDA......R1
Extracode
PR120/LV Low Voltage measuring module 24-48 V DC 065223*
PR120/V - PR120/LV Internal connection on upper terminals 058251**
* extracode to be specified with the circuit breaker code to have the low voltage measuring module PR120/LV
** The Emax DC withdrawable mobile part is supplied ad standard for incoming power from the bottom terminals (PR120/V internal connection on
bottom terminals).
In case of incoming power from the upper terminals an extracode must be specified: 1SDA058251R1 (PR120/V internal connection on upper
terminals).

Ordering codes
SACE Emax FP fixed parts
750 V DC 1000 V DC
1SDA......R1
3 Poles 4 Poles
E2 FP = Fixed part
VR 059895 059906
Withdrawable (W) - FP
E3 FP = Fixed part
VR 059896 059907
E4 FP = Fixed part
VR 059897 059137
E6 FP = Fixed part
VR 059140 059143
1SDA......R1
Extracode*
U rear Connection kit FP E2-E6 DC on upper terminals 065169**
U rear Connection kit FP E2-E6 DC on upper terminals 065169***
* extracode to be specified with the fixed part whenever used with Emax DC to include the mandatory U rear connection kits
** extracode to be specified for incoming power from the bottom terminals
*** extracode to be specified for incoming power from the upper terminals

Annex To The Technical Catalogue Low Voltage Switch-Disconnectors and Automatic Circuit-Breakers For Direct Current Applications

Uploaded by

Copyright:

Available Formats

Annex To The Technical Catalogue Low Voltage Switch-Disconnectors and Automatic Circuit-Breakers For Direct Current Applications

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Annex To The Technical Catalogue Low Voltage Switch-Disconnectors and Automatic Circuit-Breakers For Direct Current Applications

Uploaded by

Copyright:

Available Formats

Annex to the technical catalogue Emax DC

Low voltage switch-disconnectors

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

SACE Emax DC switch-disconnectors for applications up to 1000 V DC . ............................. 3

SACE Emax DC: Direct Current Applications .......................................................................... 4

Protection trip units and trip curves ......................................................................................... 8

Overall dimensions ................................................................................................................. 24

Circuit diagrams ..................................................................................................................... 33

Ordering codes . ..................................................................................................................... 42

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

(1) Without intentional delays.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

E1B/E MS E2N/E MS E3H/E MS E4H/E MS* E6H/E MS*

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

The main applications of direct current are:

4. Navy, Alternative Energy Conversion, …

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Both Polarities Insulated from Earth

One polarity connected to earth

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Median Point connected to Earth

The breaker must be inserted on both polarities.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

INCOMING POWER FROM UPPER TERMINALS

INCOMING POWER FROM BOTTOM TERMINALS

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

The PR122/DC offers the following protection functions:

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

L Release between 1.05 and 1.25 x I1 ± 20%

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Power supply from Minimum Voltage Threshold

PR122/DC PR120/D-M PR120/K

1 Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

The PR123/DC offers the following protection functions:

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Trip threshold Trip time

L Release between 1.05 and 1.25 x I1 ± 20%

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Power supply from Minimum Voltage Threshold

PR123/DC PR120/D-M PR120/K

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Optional Modules for Electronic Trip units

Code Internal Description PR123/DC

Code External Description PR123/DC

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

PR122/DC PR123/DC PR122/DC-PR123/DC

Signalling from functions

(1) please ask ABB for further details

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

The ranges Automatic circuit-breakers Switch-disconnectors

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

INCOMING POWER FROM BOTTOM TERMINALS 7