Camarines Norte State College

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

Republic of the Philippines

CAMARINES NORTE STATE COLLEGE


F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
EE 28 – Professional Elective 2 (Power System Analysis and Design)
EE117
MODULE 2
Title: Fundamentals

I. Introduction
The objective of this chapter is to review basic concepts and establish terminology and notation.

II. Phasors
A sinusoidal voltage or current at constant frequency is characterized by two parameters: a maximum value
and a phase angle. A voltage

𝑣(𝑡) = 𝑉𝑚𝑎𝑥 cos(𝜔𝑡 + 𝛿) (2.2.1)

has a maximum value 𝑉𝑚𝑎𝑥 hand a phase angle 𝛿 when referenced to cos(𝜔𝑡). The root-mean-square (rms) value,
also called the effective value, of the sinusoidal voltage is
𝑉𝑚𝑎𝑥
𝑉= (2.1.2)
√2

Euler’s identity, (𝑒 𝑗∅ ) = cos ∅ + 𝑗𝑠𝑖𝑛∅, can be used to express a sinusoidal in terms of phasor. For the above
voltage above,

𝑣(𝑡) = 𝑅𝑒[𝑉𝑚𝑎𝑥𝑒 𝑗(𝜔𝑡+𝛿) ]


= 𝑅𝑒[√2(𝑉𝑒 𝑗𝛿 )𝑒 𝑗𝜔𝑡 ] (2.1.3)

Where 𝑗 = √−1and Re denotes “real part of”. The rms phasor representation of the voltage is given in three
forms – exponential, polar and rectangular:

(2.1.4)

A phasor can be easily converts from one form to another. Conversion from polar to rectangular is shown in
the phasor diagram of Figure 2.1. Euler’s identity can be used to convert from exponential to rectangular form.

Activity 1: Given the sinusoid 𝑣(𝑡) = 169.7cos(𝜔𝑡 + 60°) volts. (a) Compute its rms value and (b) express the given
sinusoids as phasors.

Activity 2: Given the sinusoids 𝑖(𝑡) = 100 cos(𝜔𝑡 + 45°) amperes. a) Compute its rms value and (b) express the given
sinusoids as phasors.

III. Instantaneous Power in Single-Phase AC Circuits

Power is the rate of change of energy with respect to time. The unit of power is a watt, which is joule per
second.

Assume that the load voltage is

𝑣(𝑡) = 𝑉𝑚𝑎𝑥 cos(𝜔𝑡 + 𝛿) (2.2.1)

CNSC-OP-VPA-01F11 Page 1 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
Purely Resistive Load

For a purely resistive load, the current into the load is in phase with the load voltage, 𝐼 = 𝑉/𝑅,and the current
into the resistive load is

𝑖𝑅 (𝑡) = 𝐼𝑅𝑚𝑎𝑥 cos(𝜔𝑡 + 𝛿) 𝑎𝑚𝑝𝑒𝑟𝑒𝑠 (2.2.2)

Where:
𝐼𝑅𝑚𝑎𝑥 = 𝑉𝑚𝑎𝑥 /𝑅

The instantaneous power absorbed by the resistor is

𝑃𝑅 (𝑡) = 𝑣(𝑡)𝑖𝑅 (𝑡) = 𝑉𝑚𝑎𝑥 𝐼𝑅𝑚𝑎𝑥 𝑐𝑜𝑠 2 (𝜔𝑡 + 𝛿) 𝑤𝑎𝑡𝑡𝑠


1
= 𝑉𝑚𝑎𝑥 𝐼𝑅𝑚𝑎𝑥 {1 + cos[2(𝜔𝑡 + 𝛿)]} 𝑤𝑎𝑡𝑡𝑠
2
= 𝑉 𝐼𝑅 {1 + cos[2(𝜔𝑡 + 𝛿)]} 𝑤𝑎𝑡𝑡𝑠 (2.2.3)

As indicated by (2.2.3), the instantaneous power absorbed by the resistance has an average value

𝑉2
𝑃𝑅 = 𝑉𝐼𝑅 = = 𝐼𝑅 2 𝑅 𝑤𝑎𝑡𝑡𝑠 (2.2.4)
𝑅

Plus a double frequency term 𝑉𝐼𝑅 cos[2(𝜔𝑡 + 𝛿)

Purely Inductive Load


𝑉
For a purely inductive load, the current lags the voltage by 90°, 𝐼𝐿 = , and
𝑗𝑋𝐿

𝑖𝐿 (𝑡) = 𝐼𝐿𝑚𝑎𝑥 cos(𝜔𝑡 + 𝛿 − 90°) 𝑎𝑚𝑝𝑒𝑟𝑒𝑠 (2.2.5

Where:
𝐼𝐿𝑚𝑎𝑥 = 𝑉𝑚𝑎𝑥 /𝑋𝐿 , and 𝑋𝐿 = 𝜔𝐿 is the inductive reactance.

The instantaneous power absorbed by the inductor is

𝑃𝐿 (𝑡) = 𝑣(𝑡)𝑖𝐿 (𝑡) = 𝑉𝑚𝑎𝑥 𝐼𝐿𝑚𝑎𝑥 𝑐𝑜𝑠(𝜔𝑡 + 𝛿) cos(𝜔𝑡 + 𝛿 − 90°) 𝑤𝑎𝑡𝑡𝑠


1
= 𝑉𝑚𝑎𝑥 𝐼𝐿𝑚𝑎𝑥 cos[2(𝜔𝑡 + 𝛿) − 90] 𝑤𝑎𝑡𝑡𝑠
2
= 𝑉 𝐼𝐿 sin[2(𝜔𝑡 + 𝛿)] 𝑤𝑎𝑡𝑡𝑠 (2.2.6)

As indicated by (2.2.6), the instantaneous power absorbed by the inductor is a double-frequency sinusoid with
zero average value.

Purely Capacitive Load


𝑉
For a purely capacitive load, the current leads the voltage by 90°, 𝐼𝐶 = , and
−𝑗𝑋𝐶

𝑖𝐶 (𝑡) = 𝐼𝐶𝑚𝑎𝑥 cos(𝜔𝑡 + 𝛿 + 90°) 𝑎𝑚𝑝𝑒𝑟𝑒𝑠 (2.2.7)

Where:
𝐼𝐶𝑚𝑎𝑥 = 𝑉𝑚𝑎𝑥 /𝑋𝐶 , and 𝑋𝐶 = 1/𝜔𝐶 is the capacitive reactance.

The instantaneous power absorbed by the capacitor is

𝑃𝐶 (𝑡) = 𝑣(𝑡)𝑖𝐶 (𝑡) = 𝑉𝑚𝑎𝑥 𝐼𝐶𝑚𝑎𝑥 𝑐𝑜𝑠(𝜔𝑡 + 𝛿) cos(𝜔𝑡 + 𝛿 + 90°) 𝑤𝑎𝑡𝑡𝑠

CNSC-OP-VPA-01F11 Page 2 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
1
= 𝑉𝑚𝑎𝑥 𝐼𝐶𝑚𝑎𝑥 cos[2(𝜔𝑡 + 𝛿) + 90] 𝑤𝑎𝑡𝑡𝑠
2
= −𝑉 𝐼𝐶 sin[2(𝜔𝑡 + 𝛿)] 𝑤𝑎𝑡𝑡𝑠 (2.2.8)

As indicated by (2.2.6), the instantaneous power absorbed by the capacitor is a double-frequency sinusoid
with zero average value.

General RLC Load

For general load composed of RLC elements under sinusoidal-steady-state excitation, the load current is of
the form

𝑖(𝑡) = 𝐼𝑚𝑎𝑥 cos(𝜔𝑡 + 𝛽) 𝑎𝑚𝑝𝑒𝑟𝑒𝑠 (2.2.9)

The instantaneous power absorbed by the load then


𝑃(𝑡) = 𝑣(𝑡)𝑖(𝑡) = 𝑉𝑚𝑎𝑥 𝐼𝑚𝑎𝑥 𝑐𝑜𝑠(𝜔𝑡 + 𝛿) cos(𝜔𝑡 + 𝛽) 𝑤𝑎𝑡𝑡𝑠
1
= 𝑉𝑚𝑎𝑥 𝐼𝑚𝑎𝑥 {cos(𝛿 − 𝛽) + cos[2(𝜔𝑡 + 𝛿) − (𝛿 − 𝛽)]} 𝑤𝑎𝑡𝑡𝑠
2
= 𝑉𝐼 cos(δ − β) + VIcos(δ − β)cos[2(𝜔𝑡 + 𝛿)] + 𝑉𝐼𝑠𝑖𝑛(𝛿 − 𝛽) sin[2(𝜔𝑡 + 𝛿)] 𝑤𝑎𝑡𝑡𝑠
𝑃(𝑡) = 𝑉𝐼𝑐𝑜𝑠(𝛿 − 𝛽){1 + cos[2(𝜔𝑡 + 𝛿)]} + 𝑉𝐼𝑠𝑖𝑛(𝑉𝐼𝑠𝑖𝑛(𝛿 − 𝛽) sin[2(𝜔𝑡 + 𝛿)] 𝑤𝑎𝑡𝑡𝑠

Letting 𝐼𝑐𝑜𝑠(𝛿 − 𝛽) = 𝐼𝑅 and 𝐼𝑠𝑖𝑛(𝛿 − 𝛽) = 𝐼𝑋 gives

(2.2.10)

Real Power

Equation (2.2.10) shows that the instantaneous power p 𝑃𝑅 (𝑡)absorbed by the resistive component of the load
is a double-frequency sinusoid with average value P given by

𝑃 = 𝑉𝐼𝑅 = 𝑉𝐼 𝑐𝑜𝑠(𝛿 − 𝛽) 𝑤𝑎𝑡𝑡𝑠 2.2.11

Power Factor

The term 𝑐𝑜𝑠(𝛿 − 𝛽) in (2.2.11) is called the power factor. The phase angle (𝛿 − 𝛽), which is the angle
between the voltage and current, is called the power factor angle.
For dc circuits, the power absorbed by a load is the product of the dc load voltage and the dc load current; for
ac circuits, the average power absorbed by a load is the product of the rms load voltage V, rms load current I, and the
power factor 𝑐𝑜𝑠(𝛿 − 𝛽), as shown by (2.2.11).
For inductive loads, the current lags the voltage, which means 𝛽 is less than 𝛿, and the power factor is said to
be lagging.
For capacitive loads, the current leads the voltage, which means 𝛽 is greater than 𝛿, and the power factor is
said to be leading.
By convention, the power factor 𝑐𝑜𝑠(𝛿 − 𝛽) is positive. If |(𝛿 − 𝛽)| is greater than 90°, then the reference
direction for current may be reversed, resulting in a positive value of 𝑐𝑜𝑠(𝛿 − 𝛽).

Reactive Power

The instantaneous power absorbed by the reactive part of the load, given by the component px(t) in (2.2.10),
is a double-frequency sinusoid with zero average value and with amplitude Q given by

𝑄 = 𝑉𝐼𝑋 = 𝑉𝐼 𝑠𝑖𝑛(𝛿 − 𝛽) 𝑣𝑎𝑟 2.2.12

CNSC-OP-VPA-01F11 Page 3 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
Activity 3 Instantaneous, Real, and Reactive Power; Power Factor

The voltage 𝑣(𝑡) = 141.4cos(𝜔𝑡 + 𝛿) is applied to a load consisting of a 10- Ω resistor in parallel with an inductive
reactance 𝑋𝐿 = 𝜔𝐿 = 3.77 𝛀. Calculate the instantaneous power absorbed by the resistor and by the inductor. Also
calculate the real and reactive power absorbed by the load, and the power factor.

Physical Significance of Real and Reactive Power

The physical significance of real power P is easily understood. The total energy absorbed by a load during a
time interval T, consisting of one cycle of the sinusoidal voltage, is PT watt-seconds (Ws). During a time interval of n
cycles, the energy absorbed is P(nT) watt-seconds, all of which is absorbed by the resistive component of the load. A
kilowatt-hour meter is designed to measure the energy absorbed by a load during a time interval (t 2 – t1), consisting of
an integral number of cycles, by integrating the real power P over the time interval (t2 – t1).

The physical significance of reactive power Q is not as easily understood. Q refers to the maximum value of
the instantaneous power absorbed by the reactive component of the load. The instantaneous reactive power, given by
the second term px(t) in (2.2.10), is alternately positive and negative, and it expresses the reversible flow of energy to
and from the reactive component of the load. Q may be positive or negative, depending on the sign of (𝛿 − 𝛽) in
(2.2.12). Reactive power Q is a useful quantity when describing the operation of power systems (this will become
evident in later chapters).

IV. Complex Power

Let the voltage across a circuit element be 𝑉 = 𝑉∠δ, and the current into the element be 𝐼 = 𝑉∠β. Then the complex
power S is the product of the voltage and the conjugate of the current:

𝑆 = 𝑉𝐼 ∗ = |𝑉∠δ||𝐼∠β|∗ = 𝑉𝐼∠(δ − β)
= 𝑉𝐼 cos(𝛿 − 𝛽) + 𝑗𝑉𝐼𝑠𝑖𝑛(𝛿 − 𝛽) (2.3.1)

Where (δ − β) is the angle between the voltage and current. Comparing (2.3.1) with (2.2.11) and (2.2.12), S is
recognized as

𝑆 = 𝑃 + 𝑗𝑄 (2.3.2)

Activity 4 Real and Reactive Power, delivered or absorbed

A single-phase voltage source with 𝑉 = 100∠130° volts delivers a current 𝐼 = 10∠10° A, which leaves the
positive terminal of the source. Calculate the source real and reactive power, and state whether the source delivers or
absorbs each of these.

CNSC-OP-VPA-01F11 Page 4 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
The load convention is used for the RLC elements shown in Figure 2.2. Therefore, the complex power
absorbed by any of these three elements can be calculated as follows. Assume a load voltage 𝑉 = 𝑉∠δ. Then, from
(2.3.1),

Resistor: (2.3.3)

Inductor: (2.3.4)

Capacitor: (2.3.5)

From these complex power expression, the following can be stated:


 A (positive-valued) resistor absorbs (positive) real power, PR = V2/R W, and zero reactive power, QR =
0 var.
 An inductor absorbs zero real power, PL = 0 W, and positive reactive power, QL = V2/ XL var.
 A capacitor absorbs zero real power, PC = 0 W, and negative reactive power, QC = V2/ XC var.
Alternatively, a capacitor delivers positive reactive power, +V2/ XC.

Power Triangle

𝑆 = √𝑃2 + 𝑄2 (2.3.6)
(δ − β) = 𝑡𝑎𝑛−1 (𝑄/𝑃) (2.3.7)
Q = P tan(δ − β) (2.3.8)
𝑃 𝑃
pf = cos(δ − β) = = (2.3.9)
𝑆 √𝑃2 +𝑄2

Activity 5 Power Triangle and Power Factor Correction

A single-phase source delivers 100 kW to a load operating at a power factor of 0.8 lagging. Calculate the
reactive power to be delivered by a capacitor connected in parallel with the load in order to raise the source power
factor to 0.95 lagging. Also draw the power triangle for the source and load. Assume that the source voltage is
constant, and neglect the line impedance between the source and load.

V. Network Equations

For circuits operating in sinusoidal-steady-state, Kirchhoff’s current law (KCL) and voltage law (KVL) apply to
phasor currents and voltages.

Nodal equations are written in the following three steps:

STEP 1 For a circuit with (N + 1) nodes (also called buses), select one bus as the reference bus and define
the voltages at the remaining buses with respect to the reference bus.

CNSC-OP-VPA-01F11 Page 5 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING

STEP 2 Transform each voltage source in series with an impedance to an equivalent current source in parallel
with that impedance. Also, show admittance values instead of impedance values on the circuit diagram. Each current
source is equal to the voltage source divided by the source impedance.

STEP 3 Write nodal equations in matrix format as follows:

(2.4.1)

Using matrix notation, (2.4.1) becomes


YV = I (2.4.2)

where Y is the (N x N) bus admittance matrix, V is the column vector of N bus voltages, and I is the column
vector of N current sources. The elements Ykn of the bus admittance matrix Y are formed as follows:

diagonal elements: Ykk = sum of admittances connected to bus k


(k = 1, 2, . . ., N) (2.4.3)

off-diagonal elements: Ykn = - (sum of admittances connected to bus k and n)


(k ≠ n) (2.4.4)

The diagonal element Ykk is called the self-admittance or the driving-point admittance of bus k, and the off-
diagonal element Ykn for k 0 n is called the mutual admittance or the transfer admittance between buses k and n.
Since Ykn = Ynk, the matrix Y is symmetric

CNSC-OP-VPA-01F11 Page 6 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
For the circuit of Figure 2.9, (2.4.1) becomes

(2.4.5)

VI. Balanced Three-Phase Circuits

Balanced Y Connections

Figure 2.10 shows a three-phase Y-connected (or ‘‘wye-connected’’) voltage source feeding a balanced-Y-
connected load.

Balanced Line-to-Neutral Voltages

An example of balanced three-phase line-to-neutral voltages is

𝑬𝒂𝒏 = 10∠0°
𝑬𝒃𝒏 = 10∠ − 120° = 10∠ + 240° (2.5.1)
𝑬𝒄𝒏 = 10∠ + 120° = 10∠ − 240° volts

CNSC-OP-VPA-01F11 Page 7 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
Balanced Line-to-Line Voltages

The voltages Eab; Ebc, and Eca between phases are called line-to-line voltages. Writing a KVL equation for a
closed path around buses a, b, and n in Figure 2.10,

𝐸𝑎𝑏 = 𝐸𝑎𝑛 − 𝐸𝑏𝑛 (2.5.2)

For the line-to-line neutral voltages of (2.5.1)

−1−𝑗√3
𝐸𝑎𝑏 = 10∠0° − 10∠ − 120° = 10 − 10[ ] (2.5.3)
2

√3+𝑗1
𝐸𝑎𝑏 = √3(10) ( ) = √3(10∠30°) 𝑣𝑜𝑙𝑡𝑠
2

Similary, the line-to-line neutral voltages of Ebc and Eca are

𝐸𝑏𝑐 = 𝐸𝑏𝑛 − 𝐸𝑐𝑛 = 10∠ − 120° − 10∠ + 120°


= √3(10)∠ − 90° 𝑣𝑜𝑙𝑡𝑠 (2.5.4)

𝐸𝑐𝑎 = 𝐸𝑐𝑛 − 𝐸𝑎𝑛 = 10∠ + 120° − 10∠0°


= √3(10)∠150° 𝑣𝑜𝑙𝑡𝑠 (2.5.5)

In a balanced three-phase Y-connected system with positive-sequence sources, the line-to-line voltages are
√3 times the line-to-neutral voltages and lead by 30° . That is,

𝐸𝑎𝑏 = √3𝐸𝑎𝑛 ∠ + 30°


𝐸𝑏𝑐 = √3𝐸𝑏𝑛 ∠ + 30° (2.5.6)
𝐸𝑐𝑎 = √3𝐸𝑐𝑛 ∠ + 30°

Balanced Line Currents

𝐼𝑎 = 𝐸𝑎𝑛 /𝑍𝑌
𝐼𝑏 = 𝐸𝑏𝑛 /𝑍𝑌 (2.5.7)
𝐼𝑐 = 𝐸𝑐𝑛 /𝑍𝑌

For example, if each phase of the Y-connected load has an impedance 𝑍𝑌 = 2∠30°𝛀, then
10∠0°
𝐼𝑎 = = 5∠ − 30° A
2∠30°
10∠−120°
𝐼𝑏 = = 5∠ − 150° A (2.5.8)
2∠30°
10∠+120°
𝐼𝑐 = = 5∠90° A
2∠30°

CNSC-OP-VPA-01F11 Page 8 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
The neutral current In is determined by writing a KCL equation at bus N in Figure 2.10

𝐼𝑛 = 𝐼𝑎 + 𝐼𝑏 + 𝐼𝑐 (2.5.9)

Using the line currents of (2.5.8)

𝐼𝑛 = 5∠ − 30° + 5∠ − 150° + 5∠90°


√3−𝑗1 −√3−𝑗1
𝐼𝑛 = 5 ( )+ 5( ) + 𝑗5 = 0 (2.5.10)
2 2

Balanced Delta Loads

The line impedances are neglected in Figure 2.14, the source line-to-line voltages are equal to the load line-
to-line voltages, and the Δ-load currents IAB, IBC, and ICA are

𝐼𝐴𝐵 = 𝐸𝑎𝑏 /𝑍Δ


𝐼𝐵𝐶 = 𝐸𝑏𝑐 /𝑍Δ (2.5.11)
𝐼𝐶𝐴 = 𝐸𝑐𝑎 /𝑍Δ

For example, if the line-to-line-voltages are given by (2.5.3) - (2.5.5)and if 𝑍Δ = 5∠30°𝛀, then the Δ-load
currents are
10∠30°
𝐼𝐴𝐵 = √3( ) = 3.464∠0° A
5∠30°
10∠−90°
𝐼𝐵𝐶 = √3 ( ) = 3.464∠ − 120° A (2.5.12)
5∠30°
10∠150°
𝐼𝐶𝐴 = √3( ) = 3.464∠120° A
5∠30°

Also, the line currents can be determined by writing a KCL equation at each bus of the Δ load, as follows:

𝐼𝑎 = 𝐼𝐴𝐵 − 𝐼𝐶𝐴 = 3.464∠0° − 3.464∠120° = √3(3.464∠ − 30°) A


𝐼𝑏 = 𝐼𝐵𝐶 − 𝐼𝐴𝐵 = 3.464∠ − 120° − 3.464∠0° = √3(3.464∠ − 150°) A (2.5.13)
𝐼𝑐 = 𝐼𝐶𝐴 − 𝐼𝐵𝐶 = 3.464∠120° − 3.464∠ − 120° = √3(3.464∠90°) A

For a balanced-Δ load supplied by a balanced positive-sequence source, the line currents into the load are √3
times the Δ -load currents and lag by 30°. That is,

𝐼𝑎 = √3𝐼𝐴𝐵 ∠ − 30°
𝐼𝑏 = √3𝐼𝐵𝐶 ∠ − 30° (2.5.14)
𝐼𝑐 = √3𝐼𝐶𝐴 ∠ − 30°

The result is summarized in Figure 2.15

CNSC-OP-VPA-01F11 Page 9 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING

Delta-Wye Conversion for Balanced Loads

For Δ load,
√3𝐸𝐴𝐵 ∠−30°
𝐼𝐴 = √3𝐼𝐴𝐵 ∠ − 30° = (2.5.15)
𝑍Δ

For Y load,
𝐸𝐴𝑁 𝐸𝐴𝐵 ∠−30°
𝐼𝐴 = = (2.5.16)
𝑍𝑌 √3𝑍Y

Comparison of (2.5.15) and (2.5.16) indicates that IA will be the same for both the Δ and Y loads when

𝑍Δ
𝑍𝑌 = (2.5.17)
3

Activity 6 Balanced Δ and Y Loads

A balanced, positive-sequence, Y-connected voltage source with 𝐸𝐴𝐵 = 480∠0° volts is applied to a balanced-Δ load
with 𝑍Δ = 30∠40°Ω. The line impedance between the source and load is 𝑍L = 1∠85°Ω for each phase. Calculate the
line currents, the Δ -load currents, and the voltages at the load terminals

Equivalent Line-to-Neutral Diagrams

When working with balanced three-phase circuits, only one phase need be analyzed. Δ loads can be
converted to Y loads, and all source and load neutrals can be connected with a zero-ohm neutral wire without
changing the solution. Then one phase of the circuit can be solved. The voltages and currents in the other two phases
are equal in magnitude to and ±120° out of phase with those of the solved phase. Figure 2.18 shows an equivalent
line-to neutral diagram for one phase of the circuit in Example 2.4.

CNSC-OP-VPA-01F11 Page 10 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
When discussing three-phase systems in this text, voltages shall be rms line-to-line voltages unless otherwise
indicated. This is standard industry practice.

VII. Power in Balanced Three-Phase Circuits

Instantaneous Power: Balanced Three-Phase Generators

Assume that the generator is operating under balanced steady-state conditions with the instantaneous
generator terminal voltage given by

𝑣𝑎𝑛 (𝑡) = √2 𝑉𝐿𝑁 cos(𝜔𝑡 + 𝛿) 𝑣𝑜𝑙𝑡𝑠 (2.6.1)

And with the instantaneous current leaving the positive terminal of phase a given by

𝑖𝑎 (𝑡) = √2 𝐼𝐿 cos(𝜔𝑡 + 𝛽) 𝑎𝑚𝑝𝑒𝑟𝑒𝑠 (2.6.2)

where VLN is the rms line-to-neutral voltage and IL is the rms line current. The instantaneous power pa(t)
delivered by phase a of the generator is

𝑝𝑎 (𝑡) = 𝑣𝑎𝑛 (𝑡)𝑖𝑎 (𝑡)


= 2 𝑉𝐿𝑁 𝐼𝐿 cos(𝜔𝑡 + 𝛿) cos(𝜔𝑡 + 𝛽) 𝑊
= 𝑉𝐿𝑁 𝐼𝐿 cos(𝛿 − 𝛽) + 𝑉𝐿𝑁 𝐼𝐿 cos(2𝜔𝑡 + 𝛿 + 𝛽) 𝑊 (2.6.3)

Assuming balanced operating conditions, the voltages and currents of phases b and c have the same
magnitudes as those of phase a and are ±120°out of phase with phase a. Therefore the instantaneous power
delivered by phase b is

𝑝𝑏 (𝑡) = 2 𝑉𝐿𝑁 𝐼𝐿 cos(𝜔𝑡 + 𝛿 − 120°) cos(𝜔𝑡 + 𝛽) − 120° 𝑊


= 𝑉𝐿𝑁 𝐼𝐿 cos(𝛿 − 𝛽) + 𝑉𝐿𝑁 𝐼𝐿 cos(2𝜔𝑡 + 𝛿 + 𝛽 − 240°) 𝑊 (2.6.4)
And by phase c,

𝑝𝑐 (𝑡) = 2 𝑉𝐿𝑁 𝐼𝐿 cos(𝜔𝑡 + 𝛿 + 120°) cos(𝜔𝑡 + 𝛽) + 120° 𝑊


= 𝑉𝐿𝑁 𝐼𝐿 cos(𝛿 − 𝛽) + 𝑉𝐿𝑁 𝐼𝐿 cos(2𝜔𝑡 + 𝛿 + 𝛽 + 240°) 𝑊 (2.6.5)

The total instantaneous power 𝑝3∅ (𝑡) delivered by the three-phase gen erator is the sum of the
instantaneous powers delivered by each phase. Using (2.6.3)–(2.6.5):
CNSC-OP-VPA-01F11 Page 11 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING

𝑝3∅ (𝑡) = 𝑝𝑎 (𝑡) + 𝑝𝑏 (𝑡) + 𝑝𝑐 (𝑡)


= 3 𝑉𝐿𝑁 𝐼𝐿 cos(𝛿 − 𝛽) [cos(2𝜔𝑡 + 𝛿 + 𝛽) 𝑊
+ cos(2𝜔𝑡 + 𝛿 + 𝛽 − 240°)
+ cos(2𝜔𝑡 + 𝛿 + 𝛽 + 240°) 𝑊 (2.6.6)

The three cosine terms within the brackets of (2.6.6) can be represented by a balanced set of three phasors.
Therefore, the sum of these three terms is zero for any value of 𝛽 , and for all values of t. Equation (2.6.6) then
reduces to

𝑝3∅ (𝑡) = 𝑃3∅ = 3 𝑉𝐿𝑁 𝐼𝐿 cos(𝛿 − 𝛽) 𝑊 (2.6.7)

Equation (2.6.7) can be written in terms of the line-to-line voltage VLL instead of the line-to-neutral voltage VLN.
Under balanced operating conditions,

𝑉𝐿𝑁 = 𝑉𝐿𝐿 /√3 and 𝑃3∅ = √3 𝑉𝐿𝐿 𝐼𝐿 cos(𝛿 − 𝛽) 𝑊 (2.6.8)

Instantaneous Power: Balanced Three-Phase Motor and Impedance Loads

The total instantaneous power absorbed by a three-phase motor under balanced steady-state conditions is
also a constant. Figure 2.19 can be used to represent a three-phase motor by reversing the line currents to enter
rather than leave the positive terminals. Then (2.6.1)–(2.6.8), valid for power delivered by a generator, are also valid
for power absorbed by a motor. These equations are also valid for the instantaneous power absorbed by a balanced
three-phase impedance load.

Complex Power: Balanced Three-Phase Generators

The phasor representations of the voltage and current in (2.6.1) and (2.6.2) are

𝑉𝑎𝑛 = 𝑉𝐿𝑁 ∠δ volts (2.6.9)


𝐼𝑎 = 𝐼𝐿 ∠β amperes (2.6.10)

where 𝐼𝑎 leaves positive terminal “𝑎” of the generator. The complex power 𝑆𝑎 delivered by phase 𝑎 of the
generator is

𝑆𝑎 = 𝑉𝑎𝑛 𝐼 ∗ 𝑎 = 𝑉𝐿𝑛 𝐼𝐿 ∠(δ − β)


= 𝑉𝐿𝑁 𝐼𝐿 cos(δ − β) + j𝑉𝐿𝑁 𝐼𝐿 sin(δ − β) (2.6.11)

Under balanced operating conditions, the complex powers delivered by phases b and c are identical to 𝑆𝑎 ,
and the total complex power 𝑆3∅ delivered by the generator is

𝑆3∅ = 𝑆𝑎 + 𝑆𝑏 + 𝑆𝑐 = 3𝑆𝑎
= 3𝑉𝐿𝑁 𝐼𝐿 ∠(δ − β)
= 3𝑉𝐿𝑁 𝐼𝐿 cos(δ − β) + j3𝑉𝐿𝑁 𝐼𝐿 sin(δ − β) (2.6.12)

In terms of the total real and reactive powers,

𝑆3∅ = 𝑃3∅ + 𝑗 𝑄3∅ (2.6.13)

Where

𝑃3∅ = 𝑅𝑒 (𝑆3∅ ) = 3𝑉𝐿𝑁 𝐼𝐿 cos(δ − β)


= √3𝑉𝐿𝐿 𝐼𝐿 cos(δ − β) 𝑊 (2.6.14)
CNSC-OP-VPA-01F11 Page 12 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING

And
𝑄3∅ = 𝐼𝑚 (𝑆3∅ ) = 3𝑉𝐿𝑁 𝐼𝐿 sin(δ − β)
= √3𝑉𝐿𝐿 𝐼𝐿 sin(δ − β) 𝑣𝑎𝑟 (2.6.15)

Also, the total apparent power is

𝑆3∅ = | 𝑆3∅ | = 3𝑉𝐿𝑁 𝐼𝐿 == √3𝑉𝐿𝐿 𝐼𝐿 𝑉𝐴 (2.6.16)

Complex Power: Balanced Three-Phase Motors

The preceding expressions for complex, real, reactive, and apparent power delivered by a three-phase
generator are also valid for the complex, real, reactive, and apparent power absorbed by a three-phase motor.

Complex Power: Balanced Wye and Balance Delta Impedance Loads

Equations (2.6.13)–(2.6.16) are also valid for balanced-Y and - Δ impedance loads. For a balanced-Y load,
the line-to-neutral voltage across the phase a load impedance and the current entering the positive terminal of that
load impedance can be represented by (2.6.9) and (2.6.10). Then (2.6.11)–(2.6.16) are valid for the power absorbed
by the balanced-Y load.

For a balanced- Δ load, the line-to-line voltage across the phase a–b load impedance and the current into the
positive terminal of that load impedance can be represented by

𝑉𝑎𝑏 = 𝑉𝐿𝐿 ∠δ volts (2.6.17)


𝐼𝑎𝑏 = 𝑉Δ ∠β A (2.6.18)

where VLL is the rms line-to-line voltage and 𝐼Δ is the rms Δ -load current. The complex power 𝑆𝑎𝑏 b absorbed
by the phase a–b load impedance is then

𝑆𝑎𝑏 = 𝑉𝑎𝑏 𝐼 ∗ 𝑎𝑏 = 𝑉𝐿𝐿 𝐼Δ ∠(δ − β) (2.6.19)

The total complex power absorbed by the Δ load is

𝑆3∅ = 𝑆𝑎𝑏 + 𝑆𝑏𝑐 + 𝑆𝑐𝑎 = 3𝑆𝑎𝑏


= 3𝑉𝐿𝐿 𝐼Δ ∠(δ − β)
= 3𝑉𝐿𝐿 𝐼Δ cos(δ − β) + j3𝑉𝐿𝐿 𝐼Δ sin(δ − β) (2.6.20)

Rewriting (2.6.19) in terms of the total real and reactive power,

𝑆3∅ = 𝑃3∅ + 𝑗 𝑄3∅


𝑃3∅ = 𝑅𝑒 (𝑆3∅ ) = 3𝑉𝐿𝑁 𝐼Δ cos(δ − β)
= √3𝑉𝐿𝐿 𝐼𝐿 cos(δ − β) 𝑊 (2.6.22)
𝑄3∅ = 𝐼𝑚 (𝑆3∅ ) = 3𝑉𝐿𝑁 𝐼Δ sin(δ − β)
= √3𝑉𝐿𝐿 𝐼𝐿 sin(δ − β) 𝑊 (2.6.23)

Where the Δ -load current 𝐼Δ is expressed in terms of the line current 𝐼L = √3𝐼Δ in (2.6.22) and (2.6.23). also
the total apparent power is

𝑆3∅ = | 𝑆3∅ | = 3𝑉𝐿𝑁 𝐼Δ == √3𝑉𝐿𝐿 𝐼𝐿 𝑉𝐴 (2.624)

Equations (2.6.21)–(2.6.24) developed for the balanced- Δ load are identical to (2.6.13)–(2.6.16).

CNSC-OP-VPA-01F11 Page 13 of 14
Revision: 0
Republic of the Philippines
CAMARINES NORTE STATE COLLEGE
F. Pimentel Avenue, Brgy. 2, Daet, Camarines Norte

COLLEGE OF ENGINEERING
Assignment Power in Balanced Three-Phase System

Two balanced three-phase motors in parallel, an induction motor drawing 400 kW at 0.8 power factor lagging and a
synchronous motor drawing 150 kVA at 0.9 power factor leading, are supplied by a balanced, three-phase 4160-volt
source. Cable impedances between the source and load are neglected, (a) Draw the power triangle for each motor
and for the combined-motor load. (b) Determine the power factor of the combined-motor load. (c) Determine the
magnitude of the line current delivered by the source. (d) A delta-connected capacitor bank is now installed in
parallel with the combined-motor load. What value of capacitive reactance is required in each leg of the capacitor
bank to make the source power factor unity? (e) Determine the magnitude of the line current delivered by the
source with the capacitor bank installed.

VIII. Advantages of Balanced Three-Phase Versus Single-Phase Systems

Prepared by:

Engr.Myrine Ysobelle S. Sioco


Instructor I

CNSC-OP-VPA-01F11 Page 14 of 14
Revision: 0

You might also like