D8T

Track-Type Tractor

Technical Specifications
Engine Service Refill Capacities
Engine Model Cat® C15 ACERT™ Fuel Tank 627 L 165 gal
Emissions U.S. EPA Tier 4 Final/ Diesel Exhaust Fluid Tank 24 L 6.3 gal
EU Stage IV/ Cooling System 86 L 22.7 gal
Korea Tier 4 Final
Engine Crankcase* 38 L 10.0 gal
Net Power (Rated) – 1,900 rpm
Power Train 155 L 41.0 gal
ISO 9249/SAE J1349 264 kW 354 hp
Final Drives (each) 12.5 L 3.3 gal
ISO 9249/SAE J1349 (DIN) 359 hp
Roller Frames (each) 65 L 17.2 gal
Engine Power (Maximum) – 1,600 rpm
Pivot Shaft Compartment 40 L 10.6 gal
ISO 14396 294 kW 394 hp
Hydraulic Tank 75 L 19.8 gal
ISO 14396 (DIN) 400 hp
* With oil filter.
Bore 137 mm 5.4 in
Stroke 172 mm 6.75 in Air Conditioning System
Displacement 15.2 L 928 in3
The air conditioning system on this machine contains the
• Net power advertised is the power available at the flywheel when fluorinated greenhouse gas refrigerant R134a (Global Warming
the engine is equipped with fan, air cleaner, muffler, and alternator. Potential = 1430). The system contains 2.5 kg of refrigerant
• No derating required up to 3566 m (11,700 ft) altitude, beyond which has a CO2 equivalent of 3.575 metric tonnes.
3566 m (11,700 ft) automatic derating occurs.
• All nonroad Tier 4 Final, Stage IV, Korea Tier 4 Final diesel
engines are required to use only Ultra Low Sulfur Diesel (ULSD)
with 15 ppm (mg/kg) of sulfur or less, or up to B20 biodiesel
blended with ULSD. B20 should meet ASTM D7467 specification
(biodiesel blend stock should meet Cat biodiesel spec, ASTM D6751
or EN 14214). Cat DEO-ULS™ or oils that meet the Cat ECF-3,
API CJ-4, and ACEA E9 specification are required. Consult your
OMM for further machine specific fuel recommendations.
• Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic
Reduction (SCR) systems must meet the requirements outlined
in the International Organization for Standardization (ISO)
standard 22241.
D8T Track-Type Tractor Specifications

Weights Undercarriage
Operating Weight Standard
Standard (Single-Shank Ripper) 39 750 kg 87,600 lb Shoe Type Moderate Service
LGP (Drawbar) 37 750 kg 83,200 lb Width of Shoe 610 mm 24 in
Shipping Weight Shoes/Side 44
Standard (Single-Shank Ripper) 30 400 kg 67,020 lb Track Rollers per Side 8
LGP (Drawbar) 31 490 kg 69,425 lb Grouser Height 78 mm 3.1 in
• Operating Weight – Standard: Includes hydraulic controls, blade, Pitch 216 mm 8.5 in
tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, Ground Clearance 613 mm 24.1 in
SU-Blade, Single-Shank Ripper, 610 mm (24 in) MS shoes, Track Gauge 2083 mm 82 in
and operator.
• Operating Weight – LGP: Includes hydraulic controls, blade, Length of Track on Ground 3206 mm 126 in
tilt cylinder, drawbar, coolant, lubricants, 100% fuel, ROPS, Ground Contact Area 3.91 m2 6,060 in2
FOPS cab, SU-Blade, 965 mm (38 in) MS shoes, and operator. Ground Pressure (ISO 16754) 90.3 kPa 13.1 psi
• Shipping Weight – Standard: Includes coolant, lubricants, LGP
20% fuel, ROPS, FOPS cab, and 610 mm (24 in) MS shoes.
• Shipping Weight – LGP: Includes coolant, lubricants, 20% fuel, Shoe Type Moderate Service
ROPS, FOPS cab, and 965 mm (38 in) MS shoes. Width of Shoe 965 mm 38 in
Shoes/Side 44
Weights – Waste Handler Track Rollers per Side 8
Operating Weight Grouser Height 78 mm 3.1 in
Waste Handler 39 650 kg 87,400 lb Pitch 216 mm 8.5 in
LGP Waste Handler 41 850 kg 92,300 lb Ground Clearance 613 mm 24.1 in
Shipping Weight Track Gauge 2337 mm 92 in
Waste Handler 33 610 kg 74,100 lb Length of Track on Ground 3206 mm 126 in
LGP Waste Handler 35 630 kg 78,550 lb Ground Contact Area 6.19 m2 9,593 in2
• Operating Weight – Standard: Includes hydraulic controls, blade, Ground Pressure (ISO 16754) 54.2 kPa 7.9 psi
tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab,
Waste SU-Blade, striker box, 610 mm (24 in) MS shoes, and operator. Hydraulic Controls
• Operating Weight – LGP: Includes hydraulic controls, blade, tilt
Pump Type Piston-type, Variable
cylinder, drawbar, coolant, lubricants, 100% fuel, ROPS, FOPS
Displacement
cab, Waste SU-Blade, 965 mm (38 in) MS shoes, striker box,
and operator. Pump Output (Steering) 284 L/min 75 gal/min
• Shipping Weight – Standard: Includes coolant, lubricants, 20% fuel, Pump Output (Implement) 244 L/min 64 gal/min
ROPS, FOPS cab, striker box, and 610 mm (24 in) MS shoes. Tilt Cylinder Rod End Flow 132 L/min 35 gal/min
• Shipping Weight – LGP: Includes coolant, lubricants, 20% fuel,
Tilt Cylinder Head End Flow 170 L/min 45 gal/min
ROPS, FOPS cab, striker box, and 965 mm (38 in) MS shoes.
Bulldozer Relief Valve Setting 24 000 kPa 3,480 psi
Tilt Cylinder Relief Valve Setting 24 000 kPa 3,480 psi
Ripper (Lift) Relief Valve Setting 24 000 kPa 3,480 psi
Ripper (Pitch) Relief Valve Setting 24 000 kPa 3,480 psi
Steering 43 000 kPa 6,240 psi
• Steering Pump output measured at 2,364 rpm (pump speed)
and 30 000 kPa (4,351 psi).
• Implement Pump output measured at 1,900 rpm and 6895 kPa
(1,000 psi).
• Electro-hydraulic pilot valve assists operations of ripper and dozer
controls. A standard hydraulic system includes four valves.
• Complete system consists of pump, tank, filter, oil cooler, valves,
lines, and control levers.

2
 D8T Track-Type Tractor Specifications

lbf × N×
Transmission 1000 1000
1 Forward 3.5 km/h 2.2 mph 160 700
1.5 Forward 4.8 km/h 3.0 mph
140 600
2 Forward 6.6 km/h 4.1 mph
3 Forward 11.3 km/h 7.0 mph 120
500
1.5 Reverse 4.8 km/h 3.0 mph

DRAWBAR PULL
2.0 Reverse 6.4 km/h 4.0 mph 100
400
2.5 Reverse 8.7 km/h 5.4 mph
80
3.0 Reverse 11.8 km/h 7.3 mph
300
Drawbar Pull 60
1 Forward 659.2 kN 148,200 lbf
200
1.5 Forward 490.8 kN 110,350 lbf 40
2 Forward 366.1 kN 82,300 lbf 100
20
3 Forward 205.8 kN 46,250 lbf
1.0 1.5 2.0 2.5 3.0
0 0
0 2 4 6 8 10 12 km/h

0 1 2 3 4 5 6 7 mph
SPEED

Ripper
Single-Shank, Multi-Shank,
Adjustable Parallelogram Adjustable Parallelogram
Number of Pockets 1 3
Overall Beam Width — 2464 mm 97 in
Maximum Clearance Raised (under tip, pinned in bottom hole) 636 mm 25 in 593 mm 23.4 in
Maximum Penetration (standard tip) 1130 mm 44.4 in 780 mm 30.7 in
Maximum Penetration Force (shank vertical) 127.3 kN 28,620 lb 124.2 kN 27,920 lb
Pry out Force 222.7 kN 50,070 lb —
Pry out Force (Multi-Shank Ripper with one tooth) — 222.9 kN 51,230 lb
Weight* (without hydraulic controls) 3957 kg 8,705 lb —
Weight
With One Shank — 3946 kg 8,681 lb
Each Additional Shank — 332 kg 732 lb
Total Operating Weight* (with SU-Blade and Ripper) 39 750 kg 87,600 lb 39 740 kg 87,610 lb
* Total Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel. ROPS, FOPS cab, blade, single-shank
610 mm (24 in) MS shoes, and operator.

3
D8T Track-Type Tractor Specifications

Winches Standards
Winch Model PA140VS • The declared dynamic operator sound pressure level is 76 dB(A)
Weight* 2136 kg 4,709 lb when “ISO 6396:2008” is used to measure the value for an enclosed
Oil Capacity 15 L 4 gal cab. The measurement was conducted at 70% of the maximum
engine cooling fan speed. The sound level may vary at different
Increased Tractor Length 781 mm 30.7 in engine cooling fan speeds. The measurement was conducted with
Winch Length 1614 mm 63.5 in the cab doors and the cab windows closed. The cab was properly
Winch Case Width 1226 mm 48.3 in installed and maintained.
Drum Width 332 mm 13.1 in • Hearing protection may be needed when the machine is operated
with an open operator station for extended periods or in a noisy
Flange Diameter 610 mm 24.0 in
environment. Hearing protection may be needed when the machine
Recommended Cable Size 29 mm 1.13 in is operated with a cab that is not properly maintained or when the
Optimal Cable Size 32 mm 1.25 in doors and windows are open for extended periods.
Drum Capacity • Sound Level Information for Machines in European Union Countries
and in Countries that Adopt the “European Union Directives” –
Recommended Cable Length 84 m 276 ft
The information below applies to only the machine configurations
Optional Cable 62 m 204 ft that have the “CE” mark on the Product Identification Plate.
• Variable speed, hydraulically driven, dual braking system, • The declared dynamic operator sound pressure level is 75 dB(A)
three roller fairlead. when “ISO 6396:2008” is used to measure the value for an enclosed
* Includes winch, mounting group, and oil. cab. The measurement was conducted at 70% of the maximum
engine cooling fan speed. The sound level may vary at different
Winch Model W12E engine cooling fan speeds. The measurement was conducted with
Weight* 2880 kg 6,350 lb the cab doors and the cab windows closed. The cab was properly
installed and maintained.
Oil Capacity 121 L 32 gal
• The declared exterior sound power level is 113 dB(A) when the
Increased Tractor Length 669 mm 26.4 in value is measured according to the dynamic test procedures
Winch Length 1485 mm 58.5 in and the conditions that are specified in “ISO 6395:2008.”
Winch Case Width 1216 mm 48.0 in The measurement was conducted at 70% of the maximum
engine cooling fan speed. The sound level may vary at different
Drum Width 281 mm 12.0 in
engine cooling fan speeds.
Flange Diameter 635 mm 25.0 in
Recommended Cable Size 29 mm 1.13 in ROPS/FOPS
Optimal Cable Size 32 mm 1.25 in • Rollover Protective Structure (ROPS) meets the following criteria:
Drum Capacity ISO 3471:2008.
Recommended Cable Length 69 m 227 ft • Falling Object Protective Structure (FOPS) meets the following
criteria: ISO 3449:2005 Level II.
Optional Cable 55 m 181 ft
• Fixed speed, PTO driven. Brakes
* Includes winch, mounting group, and oil. • Crawler Machine Brake Requirements meets the following criteria:
ISO 10265:2008.

Track Shoes
610 mm (24 in) 660 mm (26 in) 700 mm (27.5 in) 710 mm (28 in) 965 mm (38 in)
Positive Pin Retention Track
Moderate Service 9 9 9
Moderate Service, Trapezoidal 9
Extreme Service 9 9 9
Extreme Service, Trapezoidal 9 9 9
Heavy Duty Extreme Service Track – 9 9 9
HDXL with DuraLink™
• Additional track shoe types/widths available by special order. Please consult your Cat dealer for details.

4
 D8T Track-Type Tractor Specifications

Blades
Capacity Width* Width Over End Bits Height Digging Depth
Semi-Universal (SU) 10.3 m3 13.4 yd3 3900 mm 12.8 ft 4042 mm 13.3 ft 1747 mm 5.7 ft 573 mm 22.56 in
SU with Rock Guard, 10.3 m3 13.4 yd3 3900 mm 12.8 ft 4042 mm 13.3 ft 2017 mm 6.6 ft 573 mm 22.56 in
Wear Plate
SU with Push Plate 10.3 m3 13.4 yd3 3900 mm 12.8 ft 4042 mm 13.3 ft 1747 mm 5.7 ft 573 mm 22.56 in
SU Landfill with Wear Plate 21.2 m3 27.8 yd3 3900 mm 12.8 ft 4042 mm 13.3 ft 2553 mm 8.4 ft 573 mm 22.56 in
SU with Performance 10.3 m3 13.4 yd3 3900 mm 12.8 ft 3962 mm 13.0 ft 1747 mm 5.7 ft 573 mm 22.56 in
Cutting Edges
SU with Rock Guard, 10.3 m3 13.4 yd3 3900 mm 12.8 ft 3962 mm 13.0 ft 2017 mm 6.6 ft 573 mm 22.56 in
Performance Cutting Edges
Universal 11.8 m3 15.4 yd3 4123 mm 13.5 ft 4265 mm 14.0 ft 1732 mm 5.7 ft 573 mm 22.56 in
Universal with Rock Guard, 11.8 m3 15.4 yd3 4123 mm 13.5 ft 4265 mm 14.0 ft 2012 mm 6.6 ft 573 mm 22.56 in
Wear Plate
Universal Landfill 23.4 m3 30.6 yd3 4123 mm 13.5 ft 4265 mm 14.0 ft 2544 mm 8.3 ft 573 mm 22.56 in
Angle Blade 5.2 m3 6.8 yd3 4531 mm 14.9 ft 5043 mm 16.5 ft 1177 mm 3.9 ft 625 mm 24.61 in
LGP SU 9.9 m3 12.9 yd3 4402 mm 14.4 ft 4543 mm 14.9 ft 1622 mm 5.3 ft 575 mm 22.64 in
LGP SU Landfill 22.2 m3 29.0 yd3 4402 mm 14.4 ft 4543 mm 14.9 ft 2454 mm 8.0 ft 575 mm 22.64 in
LGP Angle 5.6 m3 7.3 yd3 5041 mm 16.5 ft 5553 mm 18.2 ft 1177 mm 3.9 ft 625 mm 24.61 in

Rear Attachment
Weight* (without Total Operating in Total Operating
Ground Clearance Maximum Tilt hydraulic controls) Weight** Weight
Semi-Universal (SU) 1255 mm 49.41 in 895 mm 35.24 in 4407 kg 9,716 lb 39 750 kg 87,634 lb SS ripper
SU with Rock Guard, 1255 mm 49.41 in 895 mm 35.24 in 4998 kg 11,019 lb 40 341 kg 88,937 lb SS ripper
Wear Plate
SU with Push Plate 1255 mm 49.41 in 895 mm 35.24 in 4655 kg 10,263 lb 39 998 kg 88,180 lb SS ripper
SU Landfill with Wear Plate 1255 mm 49.41 in 895 mm 35.24 in 5251 kg 11,576 lb 39 650 kg 87,413 lb striker box
SU with Performance 1255 mm 49.41 in 895 mm 35.24 in 4547 kg 10,024 lb 39 890 kg 87,942 lb SS ripper
Cutting Edges
SU with Rock Guard, 1255 mm 49.41 in 895 mm 35.24 in 5130 kg 11,310 lb 40 473 kg 89,228 lb SS ripper
Performance Cutting Edges
Universal 1230 mm 48.43 in 968 mm 38.11 in 4895 kg 10,792 lb 40 238 kg 88,709 lb SS ripper
Universal with Rock Guard, 1230 mm 48.43 in 968 mm 38.11 in 5454 kg 12,024 lb 40 797 kg 89,942 lb SS ripper
Wear Plate
Universal Landfill 1230 mm 48.43 in 968 mm 38.11 in 5840 kg 12,876 lb 40 239 kg 88,712 lb striker box
Angle Blade 1323 mm 52.09 in 733 mm 28.86 in 5121 kg 11,289 lb 40 464 kg 89,208 lb SS ripper
LGP SU 1228 mm 48.35 in 859 mm 33.82 in 4703 kg 10,368 lb 37 750 kg 83,224 lb drawbar
LGP SU Landfill 1228 mm 48.35 in 859 mm 33.82 in 5062 kg 11,159 lb 41 850 kg 92,263 lb striker box
LGP Angle 1323 mm 52.09 in 657 mm 25.87 in 5714 kg 12,597 lb 38 761 kg 85,453 lb drawbar
* Includes blade tilt cylinder.
** Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, rear attachment,
610 mm (24 in) MS shoes, and operator.

5
D8T Track-Type Tractor Specifications

Dimensions
All dimensions are approximate.

7
1 4 6
2 5

Standard Non-Suspended LGP*

1 Track Gauge 2083 mm 82.0 in 2083 mm 82.0 in 2337 mm 92.0 in
2 Width of Tractor
Over Trunnions 3057 mm 120.4 in 3057 mm 120.4 in 3311 mm 130.4 in
Without Trunnions (standard shoe width) 2693 mm 106.0 in 2693 mm 106.0 in 3302 mm 130.0 in
3 Machine Height**, from Tip of Grouser
Exhaust Stack 3472 mm 136.7 in 3463 mm 136.3 in 3295 mm 129.7 in
EROPS (to top of railing) 3566 mm 140.4 in 3575 mm 140.7 in 3566 mm 140.4 in
4 Length of Track on Ground 3206 mm 126.2 in 3258 mm 128.3 in 3206 mm 126.2 in
5 Length of Basic Tractor (tag link trunnion to tip of rear grouser) 4647 mm 183.0 in 4647 mm 183.0 in 4647 mm 183.0 in
With the following attachments add:
Ripper – Single-Shank (with tip at ground line) 1519 mm 59.8 in 1519 mm 59.8 in Not Available
Ripper – Multi-Shank (with tip at ground line) 1613 mm 63.5 in 1613 mm 63.5 in Not Available
SU Blade 1904 mm 75.0 in 1904 mm 75.0 in 1904 mm 75.0 in
U Blade 2241 mm 88.2 in 2241 mm 88.2 in Not Available
A Blade (not angled) 2027 mm 79.8 in 2027 mm 79.8 in Not Available
A Blade (angled 25 degrees) 3068 mm 120.8 in 3068 mm 120.8 in Not Available
Drawbar 406 mm 16.0 in 406 mm 16.0 in 406 mm 16.0 in
6 Height of Grouser 78 mm 3.1 in 78 mm 3.1 in 78 mm 3.1 in
7 Ground Clearance 613 mm 24.1 in 606 mm 23.8 in 613 mm 24.1 in

*Standard shoe width of D8T LGP with non-suspended undercarriage is 965 mm (38 in).
**When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).

6
 D8T Standard and Optional Equipment

Standard and Optional Equipment

Standard and optional equipment may vary. Consult your Cat dealer for details.

Standard Optional Standard Optional

POWER TRAIN CAT CONNECT TECHNOLOGY
Cat C15 ACERT Diesel Engine, 9 Attachment Ready Option (ARO) 9
electronic unit injection AutoCarry/AutoRip, single tilt 9
Engine mounted aftertreatment to meet 9 or dual tilt
Tier 4 Final/Stage IV/Korea Tier 4 Final Cat GRADE with 3D 9
emission standards
Cat GRADE with Slope Assist 9
24V electric start 9
Cat Slope Indicate 9
Aftercooler, air-to-air (ATAAC) 9
COMMAND for Dozing Ready 9
Air filter, with electronic service indicator 9
Grade Control Ready 9
Brakes, Extreme Service 9
Product Link™ – Cellular or Dual Mode 9
Coolant, extended life 9
OPERATOR ENVIRONMENT
Drains, ecology, power train 9
Access/egress lighting with 9
Engine precleaner with screen 9 shutdown timer
Engine, thermal shield 9 Armrests, adjustable 9
Fan, suction, auto reversing 9 Cab glass – enhanced 40 psi 9
Four planet, double-reduction planetary 9 Cab glass – enhanced dual pane 9
final drives
Cab, ROPS/FOPS, sound suppressed 9
Fuel priming pump, electric 9
Deactivation switch, hydraulic controls 9
Full autoshift 9
Decelerator pedal 9
High performance single plane 9
cooling system Governor switch, electronic 9
Oil change system, high speed 9 Heater and ventilation 9
Parking brake, electronic 9 Interior LED courtesy lights 9
Precleaner, strata-tube dust ejector 9 Mirror, rearview 9
Prescreener 9 Provision for wire passage in/out of cab 9
Radiator, 6.35 fins per inch, debris 9 Radio, AM/FM, Bluetooth ®
9
Sound attenuated exhaust system 9 ROPS mounted air conditioner 9
Starting aid, automatic ether 9 Seat belt, retractable 9
Torque divider with lock-up clutch 9 Seat, cloth, air-suspension 9
Transmission control module, electronic 9 Seat, cloth, heated 9
Transmission, electronically-controlled 9 Seat, heated and ventilated 9
powershift Touchscreen operator interface 9
Turbocharger 9 Visibility arrangement – mirrors 9
Water separator 9 Visibility arrangement – single camera 9
Window shades 9
Wipers, intermittent 9
(continued on next page)

7
D8T Standard and Optional Equipment

Standard and Optional Equipment (continued)

Standard and optional equipment may vary. Consult your Cat dealer for details.

Standard Optional Standard Optional

UNDERCARRIAGE HYDRAULICS
Gauge arrangements – Standard or LGP 9 Dozer tilt hydraulics – dual tilt 9
Rollers and idlers, lifetime lubricated 9 Dozer tilt hydraulics – single tilt 9
Sprocket rim segments, replaceable 9 Electronically enabled quick drop valve 9
Suspension-type undercarriage 9 Hydraulics, electronically controlled, 9
8-roller tubular track roller frame 9 load-sensing dozer lift and tilt
(carrier roller ready) Hydraulics, electronically controlled, 9
Track adjusters, hydraulic 9 load-sensing rear hydraulics, ripper
or winch ready
Track guide 9
Hydraulics, independent steering 9
Two-piece master links 9 and work tool pumps
Positive Pin Retention (PPR) 9 Hydraulics, ripper 9
undercarriage – 44 section track, sealed
and lubricated, single grouser shoes Hydraulics, winch 9
610 mm (24 in) PPR moderate 9 ELECTRICAL
service shoes* Alarm, back-up 9
PPR undercarriage, suspended, guarded 9 Converter, 24V to 12V 9
PPR undercarriage, arctic 9 Diagnostic connector 9
Heavy Duty, Extended Life (HDXL) 9 Ground level service center 9
undercarriage – 44 section track, sealed with hour meter
and lubricated, single grouser shoes Horn, forward warning 9
HDXL undercarriage, suspended 9 Light, warning strobe 9
HDXL undercarriage, suspended, guarded 9 Light, warning strobe mount 9
HDXL undercarriage, arctic 9 Lights – premium light package 9
Carrier rollers, suspended 9 Lights – six-light package 9
Carrier rollers, suspended – arctic 9 BULLDOZERS (see chart for available blade options)
Carrier rollers, none 9 8SU/U – basic, guarded or 9
Final drives, standard or LGP 9 dual tilt guarded
Final drives, standard or LGP, guarded 9 8SU LGP – basic 9
Final drives, standard, arctic 9 8 LGP – single tilt guarded or 9
dual tilt guarded
*For optional track shoe offerings, please refer to chart on page 4. 8A 9
(continued on next page)

8
 D8T Standard and Optional Equipment

Standard and Optional Equipment (continued)

Standard and optional equipment may vary. Consult your Cat dealer for details.

Standard Optional Standard Optional

PUSH ARMS FLUIDS, LUBRICANTS, COOLANTS
Single tilt, standard 9 Engine coolant, standard (–37° C/–35° F) 9
Single tilt, extreme 9 Engine coolant, arctic (–51° C/–60° F) 9
Dual tilt, standard or extreme 9 OTHER STANDARD EQUIPMENT
BOTTOM GUARDS Equalizer bar, pinned 9
Hinged 9 Front pull device 9
Powered 9 HVAC box – corrosive resistant 9
Heavy duty, sealed 9 Mounting, lift cylinders 9
Wood chip 9 Oil cooler, hydraulic 9
Bottom guards with front counterweight 9 Product Link 9
REAR ATTACHMENTS S·O·SSM sampling ports 9
Ripper – single-shank 9 Steering, electronically controlled 9
Ripper – single-shank with pin puller 9 power differential
Ripper – single-shank with striker bar 9 Vandalism protection for fluid 9
compartments
Ripper – single-shank with puller 9
and striker bar Engine compartment service light 9
Ripper – multi-shank 9 GUARDS
Ripper – multi-shank with striker bar 9 Guard, fan debris 9
Counterweight, rear 9 Guard, fast fuel 9
Drawbar, rigid 9 Guard, fuel tank 9
Rear striker bar 9 Guard, grill debris 9
Winch, PA140VS, variable speed 9 Rear screen 9
Winch, W12E PTO 9 Striker bars, front, suspended 9
STARTERS, BATTERIES, AND ALTERNATORS Sweeps group 9
Batteries – Heavy Duty 9 OTHER ATTACHMENTS
Batteries – Arctic 9 Black paint, blade 9
Alternators – 150 Amp 9 Grab handles, push arm 9
Alternators – 150 Amp, ducted 9
Starting aids – engine heaters 9
Heater, engine coolant (120V) 9

9
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web AEXQ2356-01 (05-2018)
at www.cat.com Replaces AEXQ2356
Build Number: 21A
© 2018 Caterpillar (North America, Europe,
All rights reserved ANZ, Turkey, Korea)

Materials and specifications are subject to change without notice. Featured machines in photos may include
additional equipment. See your Cat dealer for available options.

CAT, CATERPILLAR, SAFETY.CAT.COM, their respective logos, “Caterpillar Yellow” and the “Power Edge”
trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may
not be used without permission.