Asme B1.20.5-1991 (2014)
Asme B1.20.5-1991 (2014)
Asme B1.20.5-1991 (2014)
GAGING FOR
DRYSEAL PIPE
THREADS
(INCH)
ASME B1.20.5-1991
(REVISION OF ANSI 81.20.5-1978)
This Standardwill be revised when the Society approves the issuance of a new
edition. There will be noaddenda or written interpretationsof the requirements
of this Standard issuedto this edition.
This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards.The Consensus Committee that approved the code or standard was
balanced to assure that individuals from competent and concerned interests have had an oppor-
tunity to participate. The proposed code or standard was made available for public review and
comment which provides an opportunity for additional public input from industry,academia, reg-
ulatory agencies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device,
or activity.
ASME does not take any position with respect to the validity of any patent rights asserted in
connection with any items mentioned in this document, anddoes not undertake to insure anyone
utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume
any such liability. Users of a code or standard are expressly advised that determination of the
validity of any such patent rights, and the risk of infringement of such rights, is entirely their
own
responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not t o
be interpreted as government or industry endorsement of this codeor standard.
ASME accepts responsibility for only those interpretations issued in accordance with governing
ASME procedures and policies which preclude the issuance of interpretations by individual vol-
unteers.
Copyright 0 1991 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.
(This Foreword is not part of ASME B1.20.5-1991.)
In 1973, the American National Standards Committee B2, which had formerly beenre-
sponsible for pipe thread standards, was absorbed by ANSI Standards Committee B1and
reorganized as subcommittee 20. A complete rewrite of the B2.2-1968 Standard on Dryseal
Pipe Threads was completed with the publication of ANSI B1.20.3-1976 for product threads
and the ANSI B1.20.5-1978 Standard for Gaging.
The product thread standard ANSI B1.20.3 establishes two classes of dryseal pipe threads:
Class 1 and Class 2. The classes differ only in inspection requirements. With Class 1 threads,
inspection ofrootand crest truncation is not specified. Class 2 threads are identical to
Class 1 threads except that inspection of root and crest truncation is required. This gaging
standard includes 6-step crest and root check gages, which, within their limitations, should be
helpful in establishing the degree of conformance of product threads.
When 6-step crest or root check gages are to be used, it is necessary to classify the product
thread size into a size range (minimum, basic, or maximum) as shown in Fig. 1. The use of
3-step L1 thread gages for NPTF threads requires estimating the one third of a turn, plus or
minus, from the basic notch on the gage to classify the thread as basic. Use of this same one
third turn estimation is required to determine minimum and maximum ranges. This Standard
includes 4-step taper thread gages to eliminate the need for estimating the one third turn de-
viation from basic necessary with 3-step or basic step gages. 3-step taper thread gages are
included in Appendix A for those who may prefer to use them.
Crest and root check gages for NPTF threads are also covered in this Standard. Prior to the
- publication of ANSI B1.20.5-1978 many gage manufacturers had calculated diameters for and
made such gages based on methods used for ANPT (MIL-P-7105) 6-step gages, which were
calculated to the extremes of the minimum and maximum zones, where most product threads
should never be, and which, further, is not the same logic used in calculating the pair of basic
steps. The NPTF 6-step gages tabulated herein are based on the mid-point of each range as
determined by the L , plug gage (minimum, basic, or maximum) for calculation of the trun-
cation limits where most of the product threads should be (see Fig. 2).
It should be noted that all references to the turns of engagement method for inspection of
product threads have been withdrawn from this Standard. Results obtained by that method
were found to quite often disagree with those obtained by the step limit method described here
within. Also, inconsistencies in the end threads on the product and gages do not provide for
a constant disengagement point between the two. This does not however preclude the use of
this method in any way as an acceptable means of inspecting taper pipe threads. When this
method is chosen, customer and vendor should agree on gaging procedures and minimum/
maximum acceptance limits on the turns of engagement. Information on this method can be
found in Appendix D for reference.
The gaging data in this Standard supersedes that givenin ANSI B1.20.5-1978. The proposed
standard was submitted by Standards Committee B1 to the Secretariat and the American Na-
tional Standards Institute. It was approved and formally designated as an American National
Standard on January 22, 1991.
...
111
Intentionally left blank
ASMESTANDARDSCOMMITTEE B1
Standardization and Unification of Screw Threads
of this Standard.)
of the Committee at the time of approval
(The following is the roster
OFFICERS
D. Emanuelli, Chairman
H. W. Ellison, Vice Chairman
R. McGinnis, Secretary
COMMITTEE PERSONNEL
R. Anderson R. LaNier
J. Bein J. Levy
A. Breed K. McCullough
R. Browning J. McMurray
R. Byrne A. Painter
D. Cadieux G. Russ
F. Cantrell R. Sabatos
R. Chamerda D. Satava
F. Ciccarone, Alternate M. Schuster
R. Dodge E. Schwartz
P. Drake R. Searr
H. W. Ellison R. Seppey
D. Emanuelli A. Shepherd
C. Erickson B. Shook
W. Farrell A. Strang
G. Flannery J. Sullivan
J. Heinz R. Tennis
W. Jatho, Alternate A. Thibodeau
F. Jones, Alternate J. Trilling
S.Johnson M. Van Derwerken
S. Kanter C. Wilson
R. Lamport
V
Intentionally left blank
CONTENTS
...
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
1 .......................................................................
Gaging 1
1.1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 How Dryseal Works ....................................................... 1
1.3 Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 Product Thread Designations ................................................ 1
1.5 InspectionofProductThreads ............................................... 2
1.6 Methods of Gaging Product Threads .......................................... 2
1.7 Coordination of Gages ..................................................... 3
UseofGages
1.8 ............................................................. 3
1.9 Direct Measurement of Crest andRoot Truncation .............................. 5
1.10 Inspection of Gages .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 TypesandFunctionsofGages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
Taper Thread Gages ........... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Thread Form .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
GageTolerance
2.4 ........................................................... 8
2.5 Working Gage Dimensions . . . . ............................................. 9
2.6 Master Gage Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figures
1 Classification of NPTF Product Thread Size Using 4-Step Gages ........................ 4
2 Identification of Steps on 6-Step Crest or Root Check Gage ............................ 4
3 Relative Position Plus and Minus Standoff .......................................... 6
4 Relative Position of Master Plugs and Rings to Working Gages ......................... 10
Tables
1 GagesandTolerances ........................................................... 2
2 Function and Application of Gages Covered in ASME B1.20.5-1991 .................... 7
3 Tolerances for Working Plug and Ring Gages ........................................ 11
4 Tolerances for Master Plug and Ring Gages ......................................... 12
5 Diameter Equivalent of Variation inLoad for Tools and Gages ......................... 13
6 Diameter Equivalent of Variation in Half Included Angle for Tools and Gages . . . . . . . . . . . . 14
7 Basic Dimensions for L1Ring Gages ............................................... 16
8 Basic Dimensions for L , Short Ring Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9 Basic Dimensions for L2 Ring Gages ............................................... 20
10 Basic Dimensions for L, Short Ring Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11 Basic Dimensions for Crest Check Ring Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
vii
12 Basic Dimensions for Root Check Ring Gages ....................................... 26
13 Basic Dimensions for L1 Plug Gages. NPTF ........................................ 28
14 Basic Dimensions for L1 Short Plug Gages .......................................... 30
15 Basic Dimensions for L , Plug Gages. NPSI ......................................... 32
16 Basic Dimensions for L3 Plug Gages ............................................... 34
17 Basic Dimensions for L, Short Plug Gages .......................................... 36
18 Basic Dimensions for Crest Check Plug Gages ....................................... 37
19 Basic Dimensions for Root Check Plug Gages ....................................... 38
20 Basic Dimensions of Master Ring Gages for L . and L3 Taper Plug Gages . . . . . . . . . . . . . . . . . 39
21 Basic Dimensions of Master Plug Gages for Z., and L, Taper Ring Gages . . . . . . . . . . . . . . . . . 40
22 Basic Dimensions of Master Gages for 6-Step Crest Ring and 6-Step Crest
PlugGages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
23 Basic Dimensions of Master Gages for 6-Step Root Ring Gages and 6-Step
RootPlug Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Appendices
A 3-Step GagesforCheckingNPTFThreads ....................................... 43
A1 WorkingGageDimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
B Measurement of Pitch Diameter of Taper Threads Having an Included
Taper of 0 . 0 6 2 5 Inch per Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
B1 Measurement of Pitch Diameter of Taper Thread Plug Gage ....................... 49
B2 Measurement of Pitch Diameter of Taper Thread Ring Gage ....................... 53
C FormulasFor Calculating 6-Step TaperPlugandRingGageDimensions ............ 57
D The TurnsEngagement Method ofGagingProductThreads ....................... 59
Figures
B1 Measurement of Pitch Diameter of Taper Thread Gages by the 2-Wire Method . . . . . . . . . . . . 50
B2 Horizontal Measurement of Pitch Diameter of Taper Thread Gages by the
3-Wire Method Using Sine Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
B3 Vertical Measurement of Pitch Diameter of Taper Thread Gages by the 3-Wire
Method Using a Sine Fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
B4 Measurement of Pitch Diameter E, of Taper Thread Gages by the 4-Wire Method . . . . . . . . . 53
B5 Measurement of Pitch Diameter E,,, of Taper Thread Gages by the 4-Wire Method . . . . . . . . . 54
B6 Measurement of Pitch Diameter of Taper Thread Ring Gage on Coordinate
Measuring Machine With Ball Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Tables
A1BasicDi.mensions for L. 3-Step Ring Gages ........................................ 44
A2 Basic Dimensions for L2 3-Step Ring Gages ........................................ 45
A3 Basic Dimensions for L . 3-Step Plug Gages. NPTF .................................. 46
A4 Basic Dimensions for L3 3-Step Plug Gages ........................................ 48
D l Basic Turns Engagement .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
viii
ASME B1.20.5-1991
NOTES:
(1) Step limit gages with 4 (or 3) steps should be used.
(2) The difference in engagement of the L , versus L z ring gages shall not exceed 0.5 turn. See para. 1.8.4.
(3) The difference in engagement of theL , versus L, plug gages shall not exceed 0.5 turn. See para. 1.8.4.
1.5 Inspection of Product Threads product threads are intended to assemble with taper dry-
seal external threads. Crest and root truncation is gen-
1.5.1 Inspection of NPTF Class 1 Threads and erally considered to be controlled by tooling or other
PTF-SAE Short Threads.Acceptability is determined means and can be verified by direct measurement.
by coordinated use of L , and L2 gages for external prod-
uct threads and L , and L3 gages for internal product
threads. Crest and root truncation is generally consid-
ered to be controlled by tooling or other means.
1.6 Methods of Gaging Product Threads
1.5.2Inspection of NPTF Class 2 Threads. Ac- 1.6.1The method of gaging dryseal pipe threads de-
ceptability is determined, in part, by coordinated use of scribed in this Standard is commonly called the limit
L , and L2 gages for external product threads and L , and
method. The limit method is intended for L , and L2 ring
' L3 gages for internal product threads. Direct measure- gages and L , and L3 plug gages of the corresponding
ment of crest and root truncation is a method that en-
4(or 3)-step design. Basic step plug and ring gages may
sures a high degree of accuracy in determining also be used. The 4-step design facilitates the use of the
compliance with this Standard for both external and in- 6-step crest and root check gages.
ternal threads, but may not be necessary or practicable.
It does not preclude the use of \other gaging methods or
inspection techniques such as L, and L2 snap or indi-
cating gages, 6-step crest or root check gages and in-
process control of tooling. This Standard covers the 1.6.2When the limit method is used NPTF external
6-step crest check gages and 6-step root check gage for and internal threads should be gaged with NPTF length
NPTF threads. (See para. 1.8.6.) gages with steps to indicate the size range to which the
product thread qualifies (minimum range, basic range,
1.5.3 Inspection of NPSFand NPSI Internal or maximum range). PTF-SAE short product threads
Threads. Functional size is determined by use of the should be gaged with NPTF gages modified with steps
applicable L , taper thread gage (see Table 1) since these to indicate the short length of hand tight engagement for
2
GAGING FOR DRYSEAL
ASME PIPE THREADS
(INCH) 61.20.5-1991
that application. Both L, and L2 gages for the external mustbemade for excessive chamfer at the small end of
threads and L, and L3 gages for internal threads are used the external thread and the large end of the internal
to inspect these types of dryseal pipe threads. thread. When this condition exists customer and vender
When the turns engagement method of gaging is used, should agree upon a common reference point to be used
the NPTF length and short length gages can beusedin inspection.
interchangeably, since the pitch diameter size at the
1.7.3 Classification of Product Thread Size
small end of the gage is the same in both cases, and the
(NPTF). When 6-step crest and/or root check gages are
step location is not used for the turns location method
used, it is necessary that the product thread be classified
of gaging.
either asa “maximum thread,” “basic thread,”or
NPSF andNPSI straight internal threads should be
“minimum thread.” Classification is based on the po-
gaged with NPTF gages modified with steps to indicate
sition of the LI ring or L , plug gages.
the minimum and maximum pitch diameters assigned to
the respective type of thread. Only the L , type gages are 1.7.3.1 For the limit method of gaging, the prod-
used on NPSF and NPSI straight internal threads (GO uct thread reference point may not directly coincide with
and NOT GO straight gages are not recommended for the L , ring or L, plug reference points (maximum, basic,
size acceptance). or minimum step). Therefore, the distance between the
maximum step and minimum step is divided into three
equal ranges as shown in Fig. 1. The ranges maybe
determined by use of 4-step L , taper thread gages or
may be approximated by eye or by turns of the gage on
the product thread. If the reference point of the product
thread lies in the minimum range, basic range or maxi-
mum range, it is termed a “minimum thread,” “basic
thread,” or “maximum thread” respectively.
3
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
I T -
GENERAL NOTE: T = 2 turns
-
Plug gage I
Maximum
Plug gage I
Basic
range range
Plug gage
-
--
I
Maximum
'range
plug gage
c
I I I
Product thread classification
per L 1 taper thread gage
determination
I
(Basic thread)
I 1 1
I
(Maximum thread)
I
MN MNT B BT MX MXT
or root check gage
GENERAL NOTE:
Example shown is for the inspection of internal product thread.
4
GAGING FOR DRYSEAL PIPE THREADS (INCH) ASME
9 9 16 1 . 2 0 . 5 - 1
than ‘12 turn from the position as established when as- 1.10 Inspection of Gages
sembled with the L , gage. When using 4(or 3)-step L2
1. IO.1 Periodic inspection of gages is necessary in
or L , gages the product thread reference pointisnot
order to detect gages worn beyond the limits specified
required to lie between the same set of steps as when
in para. 2.4. Since gage wear is directly related to gage
assembled with the L , gage and may lie beyond the
use, frequency of inspection must be determined by each
maximum and minimum steps. Steps on L , and L3 gages
user.
are for reference only.
1.8.56-Step Crest Check Gage or 6-Step Root 1 .10.2Working gages are generally inspected by
Check Gage. When using the limit method of gaging, using master gages. Master gages provide a functional
the gage must correlate to the product thread classifi- check of all thread elements (except crest and root trun-
cation as determined by the L , gage. Specifically, if the cation) but will not detect uneven wear. Consequently,
product thread is classified as a “maximum thread,” the the individual thread elements (pitch diameter, lead,
product thread reference point must lie between the two taper, half angle, truncation, and major or minor diam-
steps of the gage marked MX and MX,. If the product eter) of working gages should be measured occasion-
thread is classified as a “basic thread,” the product ally. Measurement of these thread elements can be made
thread reference point must lie between the steps of the by the user but because of the relatively elaborate equip-
gage marked B and B,. If the product thread is classified ment and procedures required, it may be most econom-
as a “minimum thread,” the product thread reference ical to send the gages to a gage manufacturer or to a
point must lie between the steps of the gage marked MN measurement laboratory.
and MN,. An identification of the six steps is shown in
Fig. 2.
1.10.3 Methods of Measuring Externally
Threaded Gages. Two-wire, three-wire, and four-wire
1.8.6 Limitations on Reliability of 6-Step Gages
methods described in Appendix B, are used for measur-
for Establishing Truncation and Width of Flats on
ing pitch diameter for taper threads. The choice from
Product Threads. Use of the 6-step gage in conjunc- these methods is a matter of preference and more often
tion with the L , thread gage presumes a perfect thread
depends on the availability of fixtures and measuring
flank contact of the gage to product thread which can
equipment. Lead and taper can be measured on measur-
never exist except on a thread with perfect flank angles, ing machines, half angle, and truncation (width of flat),
lead, and taper. The product thread groove is always by optical projection.
wider than the gage thread ridge which fits into it. The
product thread root flat is therefore always wider than
indicated by the position of the 6-step gage while the 1.10.4 Methods of Measuring Internally
crest flat is always narrower. (See para. 1.5.2.) Threaded Gages. Internal threads are generally much
more difficult to measure directly than external threads.
There are no standard methods for measuring pitch di-
ameter although it is generally determined by mating the
1.9 Direct Measurement of Crest and Root ring gage to a master taper thread plug gage as described
Truncation in Appendix B. Measurement of pitch diameter can also
be made by using the ball probe method described in
One method of direct measurement of truncation is
Appendix B. Lead and taper can be measured on mea-
by optical projection. With this method, it is difficult to
suring machines, half angle, and truncation, by optical
measure truncation as defined. Therefore, measurement
projection of a cast.
of the equivalent width of flat is a common practice.
External threads can be directly projected, but internal
threads must either be sectioned and projected by re- 1.10.5 Standoff. The relative position of a gage
flection or cast’ and the cast used for direct projection. when mated to another gage or workpiece (see Fig. 3).
Magnification should not be less than 20X and may need It is recommended thatthe standoff of each working gage
to begreater for accurate resolution of small size threads. from its respective master be determined and that the
value be taken intoconsideration when the working gage
‘Some silicon rubber molding compounds have been found to be good is used. Working gages should bereplacedwhen the
casting material. standoff is more than one-half turn from basic size.
5
ASME 61.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
Work Work
piece piece
standoff
at gaging
notch
Work Work
piece 1 piece
Plug gage
Minus ( 4
standoff
at small end at small end
6
GAGING FOR DRYSEAL PIPE THREADS (INCH) ASME B1.20.5-I991
MASTER GAGES
7
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
cluding root and crest truncation) of that portion of the NOTE: Themaximumwidth of root relief permissible equals the
thread engaged when mating dryseal pipe threads are maximum product root width (see ANSI B1.20.3).
assembled handtight. 2.3.2 RootCheck RingandPlug Gages. Root
2.1.2.2 f, Taper Thread PlugGage or f3 check ring and plug gages have a triangular thread form
ShortTaper Thread Plug Gage. Checks the func- with truncated crests and cleared roots. The angle be-
tional diameter, (excluding root and crest truncation) of tween the flanks of the threads is 50 degrees when mea-
the threads provided for wrench make-up beyond the L, sured on an axial plane and the line bisecting this angle
length, and in relation to the position of the L, plug, is perpendicular to the axis of the threads. (The 50 de-
provides an indication of taper deviation, or excessive gree thread angle enables the gage to contact only at the
root truncation. root of the product thread so that root truncation can be
checked.) Crests are truncated to provide a gage maxi-
2.1.2.3 CrestCheck Plug Gage. Checks the mum flat width that is 0.001 inch smaller than the min-
minor diameter (crest truncation) of the internal thread. imum flat width of the product thread root. The form of
2.1.2.4 RootCheckPlug Gage. Checks the the thread root is optional, but must clear a 0 . 1 5 ~flat.
major diameter (root truncation) of the internal thread. 2.3.3 Crest Check RingandPlug Gages. Crest
2.1.3 All dimensions in this Standard, including all check ring and plug gages are plain (cylindrical) taper
tables are in inches unless otherwise specified. gages.
2.3.4 Optical Projection of Thread Form. Visual
2 . 2 Taper Thread Gages method of inspection may be used in lieu of the root
check and crest check ring and plug gages. The threads
There are two kind of gages: working gages and mas- of tools and the threads of a percentage of the product
ter gages. external threads, or casts in the case of internal threads,
2.2.1 Working gages are used to check product may be visually checked by optical comparator projec-
threads during manufacture and for acceptance. Each set tion (at least 20X) for thread form and truncation.
of working gages consists of L , and L2 ring gages and
L, and L3 plug gages. For Class 2 product threads, crest 2 . 4 Gage Tolerance
check and root check gages should also be included in
a set of working gages. In the manufacture of gages, variations from basic di-
mensions are unavoidable. Furthermore, gages will wear
2.2.2 Master gages are used as a reference to check in use. In order to fix the maximum allowable variations
new working gages and for surveillance of used working of gages, tolerances have been established and are ap-
gages and classification of them as to standoff. How- plied to the basic dimensions given in Section 2.5.
ever, it is not necessary to have master gages if other
methods of inspecting working gages are employed. 2.4.1 WorkingGageTolerance. Manufacturing
Each set of master gages consists of an LIIL3 master tolerances for working gages are given in Table 3. The
ring gage and an LlIL2 master plug gage. (See Fig. 4.) maximum wear on a working gage shall not be more
than the equivalent of one-half turn as determined by
the master gage.
2 . 3 ThreadForm
2.4.2 Master Gage Tolerance. Master gage toler-
2.3.1 L , and L2 Taper Thread Ring Gages and ances are shown in Table 4. Master gages should be a
,
f and f Taper Thread Plug Gages. L1 and L2 ring matched set (plug and ring) and accompanied by a rec-
gages and L, and L3 plug gages have a triangular thread ord of the amount they vary from being flush to basic in
form with truncated crests and cleared roots. The angle terms of standoff specified in three decimal places.
between the flanks of the threads is 60 degrees when
measured on an axial plane and the line bisecting this 2.4.3 Relationship of LeadandAngleVari-
angle is perpendicular to the axisof the threads making ations to Pitch Diameter Tolerance
each half angle equal to 30 degrees. L1 ring and plug 2.4.3.1 Functional size of pitch diameter is af-
gages have a truncation parallel to the pitch line, equal fected by variations in lead and angle and the effect of
to the maximum root truncation of the product thread, these variations can be expressed as an equivalent vari-
while crests of L2 ring and L3 plug gages have a trun- ation in diameter. Diameter equivalents of variations in
cation of 0 . 2 0 ~The
. form of the thread root is optional, lead and half angle are given in Tables 4 and 5 respec-
flat ( 0 . 0 3 6 ~
but must clear a 0 . 0 4 2 ~ truncation). tively.
8
GAGING FOR DRYSEALPIPETHREADS (INCH) ASME 81.20.5-1991
2.4.3.2 These corrections are always added to the 2.5.6 Root Check Ring Gage (for checking NPTF
pitch diameter in the case of external threads and sub- threads). See Table 12.
tracted in the case of internal threads regardless of
2.5.7 f Plug Gage (for checking NPTF threads).
whether the lead or angle variations are plus or minus.
See Table 13. The3-step design is included in Appendix
2.4.3.3 The diameter equivalent for lead and an- A for reference.
gle variations plus the pitch diameter variation multi-
2.5.8 f, Short Plug Gage (for checking PTF-SAE
plied by 16 gives the longitudinal variation from basic SHORT and NPSF threads). See Table 14.
at the gaging notch.
2.5.9 f 1 Plug Gage, NPSl (for checking NPSI
threads). See Table 15.
2.5 Working Gage Dimensions
2.5.10 f, Plug Gage (for
checking NPTF
The basic dimensions given in the following para- threads). See Table 16.
graphs pertain to working gages. Both 4-step and basic
2.5.1 1 f, Short Plug Gage (for checking PTF-
notch gage designs are covered for L , and L2 ring gages
SAE SHORT threads). See Table 17.
and L , and L, plug gages. Only the 6-step design is cov-
ered for crest and root check gages. The 4-step gages 2.5.12Crest Check Plug Gage (for checking
are included because they facilitate the use of the 6-step NPTF threads). See Table 18.
crest and root gages. Although the basic notch gage is
2.5.13Root Check Plug Gage (for checking
more difficult to use in conjunction with the 6-step crest
NPTF threads). See Table 19.
and root gages, it is more economical to manufacture
and may be used for checking both NPTF threads, and
PTF-SAE SHORT threads. 2.6 Master Gage Dimensions
2.5.1 f 1 Ring Gage (for checking NPTF The basic dimensions given in the following tables
threads). The 3-step design is included in Appendix A pertain to master gages for NPTF threads.
for reference. (See Table 7.)
2.6.1 Master Ring Gage (for checking NPTF
2.5.2 L1 Short Ring Gage (for checking PTF-SAE Working Plug Gages). See Table 20.
SHORT threads). See Table 8.
2.6.2 Master Plug Gage (forchecking NPTF
2.5.3 f, Ring Gage (for checking NPTF Working Ring Gages). See Table 21.
threads). The 3-step design is included in Appendix A
2.6.3 Master Ring and Plug Gages (for check-
for reference. (See Table 9.)
ing NPTF 6-StepWorking Crest Ring and Plug
2.5.4 f 2 Short Ring Gage (for checking PTF-SAE Gages). See Table 22.
SHORT threads). See Table 10.
2.6.4 Master Ring and Plug Gages (for check-
2.5.5Crest Check Ring Gage (for checking ing NPTF 6-StepWorking Root Ring and Plug
NPTF threads). See Table 11. Gages). See Table 23.
9
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
(a) Ll/L, Master Plug With L , / L , Master Ring (d) L 1 / L 3 Master Ring With L,/L, Master Plug
(c) L,/L, Master Plug With La Ring (r) L , / L , Master Ring With L, Plug
GENERAL NOTE:
Master gage set consists of one full-form L , / L z master taper thread plug gage and one full-form L , / L , master taper thread
ring gage.
10
GAGING FOR DRYSEAL PIPE THREADS(INCH) ASME B1.20.5-1991
11
2 - 14 0.0003 0.0002 0.0003 10 15 0.0006 0.0009 0.0015 0.0015 0.00097 0.00130 0.036
3/4 - 14 0.0003 0.0002 0.0003 10 15 0.0006 0.0009 0.0015 0.0015 0.00097 0.00130 0.036
1 - 1 11 '2 0.0003 0.0003 0.0004 10 15 0.0008 0.0012 0.0015 0.0015 0.00121 0.00157 0.044
1 1/4 - 1 1 'h 0.0003 0.0003 0.0004 10 15 0.0008 0.0012 0.0015 0.0015 0.00121 0.00157 0.044
1 1/2 - 1 1 112 0.0003 0.0003 0.0004 10 15 0.0008 0.001 2 0.0015 0.0015 0.00121 0.00157 0.044
2 - 1 1 'h 0.0003 0.0003 0.0004 10 15 0.0008 0.0012 0.0015 0.0015 0.001 21 0.00157 0.044
2 '12 - 8 0.0005 0.0004 0.0005 7 10 0.0010 0.0014 0.0019 0.0019 0.001 58 0.00193 0.056
3 - 8 0.0005 0.0004 0.0005 7 10 0.0010 0.0014 0.0019 0.0019 0.001 58 0.00193 0.056
- -
GENERAL NOTES:
(a) The tolerances for the length from small end to gaging notch of the L , and L3 plug gages shall be +O.OOO and- -0.001 for
sizes 1
'16 t o 2 inclusive and +O.OOO and -0.002 for sizes 2 % and larger.
(b) The tolerances for the overall thread length L, of the plug gage shall be f 1 / 6 4 and -0 for sizes '116 t o 2 inclusive and + ' I 3 2 and
-0 for sizes 2 '12 and larger.
(c) Tolerance for the thickness of the L l and L2 ring gages shall be -0.000 and +0.001 for sizes '116 t o 2 inclusive and -0.000
and +0.002 for sizes 2l/2 and larger.
(d) The tolerances for step lengths of all 4-step gages is as follows:
Step 1, +0.002 and -0.000
Step 2, f 0.001
Step 3, f 0.001
Step 4, +O.OOO and -0.002
NOTES:
( 1) To be measured at the gaging notch of pluggage.
(2) Allowable variation in lead between any two threadsin L1 length of gage.
(3) The lead and taper on plug and ring gages shall be measured along the pitch line omitting the incomplete threads at each end.
(4) In solving for the correction in diameter for angle variation the average variation in half angle for the t w o sides of thread
regardless of their signs, should be taken.
(5) Allowable variation in taper in L , length of gage.
+ +
(6) Total cumulative tolerance on pitch diameter = PD tolerance diameter equivalent of lead variation diameter equivalent of
half angle variation.
(7) Between the plug gage gaging notch and the large end of the ring gage when dimensions are at opposite extremes of the
tolerance limits.
( 8 ) Maximum possible interchange standoff, any ring against any plug other than its master plug, may occur when taper variations
are zero and all other dimensions are at opposite extreme tolerance limits. Actual standoff should be well within these maxi-
mum limits. Refer t o Tables 5 and 6 for diameter equivalentsof lead and half angle variations respectively.
11
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
1 i
Toler- Toler-
Tolerance ance ance Total Cumulative
Toler- Tolerance [Note (411 Tolerance on on [Note (611
ance [Notes (21, (311 on Half [Notes (3). (511 Major Minor Tolerances on Stand-
[Note ( 111 on Lead Angle, min on Taper Diam. Diam. Pitch Diam. off
on Pitch [Notes
Nominal Diam. Plugs Ring: Plugs Rings Plugs Rings ( 7 ) . (811
Size (k1 Plugs Rings ( + I (k1 (+I (-1 (-1 (+) Plugs Rings (2)
1 2 3 4 5 6 7 8 9 10 11 12 13
1/16-27 0.0001 0.0001 0.0001 5 8 12 0.0001! 0.0003 0.0006 3.0006 0.0004 0.00056 0.002
‘/E -27 0.0001 0.0001 0.0001 5 8 12 0.0001! 0.0003 0.0006 3.0006 0.0004 0.00056 0.002
’/4 - 18 0.0001 0.0001 0.0001 5 8 12 0.0002 0.0003 0.0006 1.0006 0.00047 0.00066 0.002
3 / ~ - 18 0.0001 0.0001 0.0001 5 8 12 0.0002 0.0003 0.0006 1.0006 0.00047 0.00066 0.002
‘h -14 0.0001 5 0.0001 0.0001 5 6 10 0.0003 0.0004 0.0007 1.0007 0.00051 0.00073 0.002
3/4 - 14 0.0001 5 0.0001 0.0001 5 6 10 0.0003 0.0004 0.0007 1.0007 0.00051 0.00073 0.002
1 -11 ‘/2 0.0001 5 0.0001 5 0.0002 6 10 0.0004 0.0005 0.0007 1.0007 0.00064 0.00089 0.002
1 114 - 1 1 1/2 0.0001 5 0.0001 5 0.0002 6 10 0.0004 0.0005 0.0007 1.0007 0.00064 0.00089 0.002
1 1/2 - 1 1 1/2 0.0001 5 0.0001 5 0.0002 6 10 0.0004 0.0005 0.0007 1.0007 0.00064 3.00089 0.002
2 - 1 1 1/2 0.0001 5 0.0001 5 0.0002 6 10 0.0004 3.0005 0.0007 1.0007 0.00064 3.00089 0.002
2 ’h - 8 0.00025 0.0002 0.00025 5 7 0.0005 3.0006 3.0009 ).0009 0.00088 3.001 07 0.003
3 - ,8 0.00025 0.0002 0.00025 5 7 0.0005 3.0006 3.0009 ).0009 0.00088 3.00107 0.003
GENERAL NOTES:
The tolerances for the length L , from small end to gaging notch o f t he plug gage shall be +O.OOO and -0.0005 for sizes ’/16
to 2 inclusive and +O.OOO and -0.001 for sizes 2’12 and larger.
The tolerances for the overall thread length L2 of the plug gage shall be +O.OOO and -0.001 for sizes ‘/16 to 2 inclusive and
+O.OOO and -0.002 for sizes 2’h and larger.
(c) Tolerances for the thickness of the ring gage shall be -0.000 and +0.001 for sizes 1 ’16 t o 2 inclusive and -0.000 and +0.002
‘h
for sizes 2 and larger.
(d) Refer to Tables 6 and 7 for diameter equivalents of lead and half angle variations respectively.
NOTES:
(1) To be measured at the gaging notch of pluggage.
(2) Allowable variation in lead between any t w o threads in L , length of gage.
( 3 ) The lead and taper on plug and ringgages shall be measured along the pitch line omitting the incomplete threads ateach end.
(4) In solving for the correction in diameter for angle variations, the average variation in half angle for the t w o sides of thread
regardless of their signs, should be taken.
(5) Allowable variation in taper in L, length of gage.
+
(6) Total cumulative tolerance on pitch diameter= PD tolerance diameter equivalent of lead variation + diameter equivalent of
half angle variation.
(7) Between master plug at gaging notchand the large end of themasrer ring gage.
(8)Tolerances listed are standoff limits for master ringto itsoriginal master pluggage. Master plug t o working ring or master ring
to working plug standoff may exceed the standoff shown but should not exceed one-half extreme standoff listed in 3,
Table
column 13.
12
GAGING FOR DRYSEAL PIPE THREADS(INCH) ASME 81.20.5-1991
I* 2 3 4 5 6 7 8 9 10 11
0.0000" 0.00000 0.00002 0.00003 0.00005 0.00007 0.00009 0.00010 0.0001 2 0.00014 0.0001 6
0.0001 " 0.0001 7 0.0001 9 0.00021 0.00023 0.00024 0.00026 0.0002a 0.00029 0.00031 0.00033
0.0002" 0.00035 0.00036 o.ooo3a 0.00040 0.00042 0.00043 0.00045 0.00047 0.00048 0.00050
0.0003" 0.00052 0.00054 0.00055 0.00057 0.00059 0.00061 0.00062 0.00064 0.00066 0.00068
0.0004" 0.00069 0.00071 0.00073 0.00074 0.00076 0.00078 0.00080 0.00081 o.oooa3 0.00085
0.0005" 0.00087 0.00088 0.00090 0.00092 0.00094 0.00095 0.00097 0.00099 0.001 00 0.001 02
0.0006" 0.00104 0.001 06 0.001 07 0.001 09 0.001 11 0.001 13 0.001 14 0.001 16 0.001 18 0.001 20
0.0007" 0.001 21 0.001 23 0.001 25 0.001 26 0.001 28 0.001 30 0.001 32 0.001 33 0.00135 0.001 37
0.0008" 0.001 39 0.001 40 0.00142 0.001 44 0.00145 0.00147 0.00149 0.001 51 0.001 52 0.001 54
0.0009" 0.001 56 0.001 58 0.001 59 0.001 61 0.001 63 0.001 65 0.001 66 0.00168 0.00170 0.001 71
0.0010" 0.001 73 0.001 75 0.00177 0.001 78 0.001 80 0.00182 0.001 84 0.00185 0.001 87 0.001 89
0.001 1 0.00191 0.001 92 0.001 94 0.00196 0.00197 0.00199 0.00201 0.00203 0.00204 0.00206
0.001 2 * 0.00208 0.00210 0.0021 1 0.0021 3 0.00215 0.0021 7 0.00218 0.00220 0.00222 0.00223
0.0013" 1.00225 0.00227 3.00229 1.00230 0.00232 3.00234 3.00236 0.00237 3.00239 , 0.00241
0.0014" 1.00242 0.00244 3.00246 1.00248 0.00249 1.00251 3.00253 0.00255 3.00256 ' 0.00258
0.0015* 1.00260 0.00262 3.00263 1.00265 0.00267 3.00268 3.00270 0.00272 3.00274 0.00275
~
GENERAL NOTE:
Diameter equivalent = 1.7326~
where 6p = variation in lead between any two threads
13
ASME 81.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
GENERAL NOTES:
(a) In solving for the diameter equivalent of angle variations the average variation in half angle for the two sides of the thread
regardless of their signs shouldbe taken.
(b) Diameter equivalent = 1.53812p tan b a , where b a = variation in half includedangle of thread expressed in minutes.
NOTE:
(1) Table is based upon an NPT gage with 0 . 1 root/crest
~ truncations with equal half-angle variations. For other gages with equal
truncations, multiply by
0 . 8 6 6 ~- 2(truncation)
0.6667~
14
TABLE 7
r
Eo -
t
Remove convolution
of partial thread
- both ends
Mark steps as shown
L, - P (Step 1)
L , - 1/3p (Step 2
TABLE 7 BASIC DIMENSIONS FOR L1 RING GAGES
Max. Min.
r Max.
Basic Range
Min. Max.
Minimum Range
Min.
Small End
Basic Pitch Minor Step 1 Step 2 Step 2 Step 3 Step 3 Step 4 Pitch M
Nominal Length, Diam., [Note (111 Diam.. [No
Size Ll €1 Diam. (L, - PI (L, - %p) (L, - ‘hp) (L, + %p) (L, + ’hp) (L, + p) €0 D
‘h6-27 0.1600 0.281 18 0.25947 0.12296 0.14766 0.1 4766 0.17234 0.17234 0.1 9704 0.271 18 0.2
’/a -27 0.1615 0.37360 0.35189 0.1 2446 0.14916 0.14916 0.1 7384 0.17384 0.19854 0.36351 0.3
‘/4 - 18 0.2278 0.491 63 0.45563 0.1 7224 0.20928 0.20928 0.24632 0.24632 0.28336 0.47739 0.4
-1 8 0.2400 0.62701 0.59101 0.18444 0.22148 0.22148 0.25852 0.25852 0.29556 0.61 201 0.5
c
4 0.75843 0.7
‘12 - 14 0.3200 0.77843 0.72871 0.24857 0.2961 9 0.2961 9 0.34381 0.34381 0.39143
3/4 - 14 0.3390 0.98887 0.9391 5 0.26757 0.31 51 9 0.31 51 9 0.36281 0.41043 0.96762
0.36281 0.9
1 -1 1’/2 0.4000 1.23853 1.17897 0.31 304 0.37102 0.37102 0.42898 0.48696 1.21 363
0.42898 1.1
1 ‘/4 - 1 1‘12 0.4200 1.58338 1.52372 0.33304 0.39102 0.39102 0.44898 0.50696 1.5571 3
0.44898 1.4
1 ‘ h -1 1‘12 0.4200 1.82234 1.76268 0.33304 0.39102 0.39102 0.44898 0.44898 0.50696 1.79609 1.7
2 - 1 1’12 0.4360 2.29627 2.23661 0.34904 0.40702 0.40702 0.46498 0.46498 0.52296 2.26902 2.2
2 ‘h- 8 0.6820 2.7621 6 2.67291 0.55700 0.64034 0.64034 0.72366 0.72366 o.80700 2.71953 2.6
3 - 8 0.7660 3.38850 3.29925 0.64100 0.72434 0.72434 0.80766 0.80766 0.89100 3.34062 3.2
GENERAL NOTE:
Gage blanks shall conform to dimensions given in ANSI 847.1 except for extra width of 4-step design.
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
3-Step Design
f#*k t-3 +
Mark ring with size and type
Example: 1/8-27 PTF-SAE SHORT L ,
L 1 short
. Mark on
Basic -// Minimum step this end
+I-+tE,
Remove convolution of
partial thread this end
Maximum
Maximum step
Bottom (Small End)
View of Ring Gage
GENERAL NOTE:
(a) Gage blanks shall conform t o dimensions given in ANSI B47.1 except for extra width of 3-step design.
(b) Master gage same as NPTF shown in Table 22.
NOTE:
(1) Minor diameter isbased on crest minimum truncation
equal to maximum root truncationof product thread(see ANSI B1.20.3).
18
GAGING FOR DRYSEAL PIPE THREADS (INCH) ASME B1.20.5-1991
19
TABLE 9
L, + 1/ 3
Remove convolution of
J
partial thread this end
Mark ring with size and type
Example: 1 /8-27 NPTF L,
L, - 1 / 3
GENERAL NOTE: The L, ring gage must seat on product thread in relation to the L , ring gage within * 1 / 2 turn.
TABLE 9 BASICDIMENSIONS FOR - L z RING GAGES
Large End T Maximum Range Basic Range T Minimum Range T Small End T
Max. Min. Max. Min. Max. Min.
Basic Pitch Minor Step 1 Step 2 Step 2 Step 3 Step 3 Step 4 Pitch Minor
Nominal Length, Diam., Diam. Diam., Diam.
Size L2 E2 [Note (111 (L, - PI (L2 - %p) (L2 - %PI (Lz + %PI (Lz + %PI (L, + p) Ex [Note (111
‘/16-27 0.261 13 0.28750 0.27024 0.22409 0.24879 0.24879 0.27347 0.27347 0.29817 0.27886 0.261 60
‘/E -27 0.26385 0.38000 0.36274 0.22681 0.25151 0.25151 0.27619 0.27619 0.30089 0.37129 0.35403
‘/4 - 1 8 0.401 78 0.50250 0.47661 0.34622 0.38326 0.38326 0.42030 0.45734 0.42030
0.4881 6 0.46227
Y E - 18 0.40778 0.63750 0.61 161 0.35222 0.38926 0.38926 0.42630 0.46334 0.62354
0.42630 0.59765
2 ‘h - 14 0.53371 0.791 79 0.75850 0.46228 0.50990 0.50990 0.55752 0.55752 0.60514 0.77396 0.74067
314 -1 4 0.5457 1 1.001 79 0.96850 0.47428 0.52190 0.52190 0.56952 0.61714 0.98440
0.56952 0.951 11
1 -1 1 ’12 0.68278 1.25630 1.21 577 0.59582 0.65379 0.65379 0.71 176 0.71 176 0.76974 1.23320 1.19267
1 ‘/4 - 1 1 ’12 0.70678 1.601 30 1.56077 0.61982 0.67780 0.67780 0.73576 0.73576 0.79374 1.57794 1.53741
1 ’/2 - 1 1‘12 0.72348 1.841 30 1.80077 0.63652 0.69450 0.69450 0.75246 0.75246 0.81044 1.81690 1.77537
2 -11 ‘12 0.75652 2.31630 2.27577 0.66956 0.72754 0.72754 0.78550 0.78550 0.84348 2.29084 2.25031
2 ‘h - 8 1.13750 2.79062 2.73237 1.01 250 1.09584 1.09584 1.17916 1.17916 1.26250 2.75434 2.69609
3 - 8 1.20000 3.41 562 3.35737 1.07500 1.15834 1.15834 1.241 66 1.24166 1.32500 3.38068 3.32243
GENERAL NOTE:
Gage blanks shall conform to dimensions given in ANSI 847.1 except for extra width of 4-step design.
NOTE:
(1) Minor diameter is based on crest minimum truncation of 0 . 2 0 ~ .
TABLE 10
3-Step Design
Remove conv
partial thread
I Maximum
w
112 -1 4 0.4623 0.42657 0.53371 0.79179 0.75850 0.77396 0.74067 0.248
w 314 - 41 0.4743 0.43857 0.54571 1.00179 0.96850 0.98440 0.951 11 0.267
1 - 1 1 112 0.5958 0.55235 0.68278 1.25630 1.21 577 1.23320 1.19267 0.313
1 114 - 1 1'12 0.6198 0.57635 0.70678 1.60130 1.56077 1.57794 1.53741 0.333
1 '/2 - 1 1112 0.6365 0.59305 0.72348 1.84130 1.80077 1.81 690 1.77637 0.333
2 - 11 '12 0.6695 0.62609 0.75652 2.31630 2.27577 1.29084 2.25031 0.349
2 '12 - 8 1.01 25 0.95000 1.13750 2.79062 2.73237 2.75434 2.69609 0.557
3 - 8 1.0750 1.01250 1.20000 3.41 562 3.35737 3.38068 3.32243 0.641
GENERAL NOTES:
(a) Gage blanks shall conform to dimensions given in ANSI 847.1 except for extra width of 3-step design.
(b) Master gage same as NPTF shown in Table 22.
NOTE:
(1) Minor diameter is based on crest minimum truncation of 0 . 2 0 ~ .
ASME 81.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
"-- MN, I B, --
1
B
7
1 MX
I
-MX,
,-
-
( 8
MN
f 1 f t I 1 1
Development - counterclockwise
1 '/2 -1 1 '12 1.9062 0.6678 0.7235 0.7258 0.781 5 0.6098 0.6655 3.38
2 -11 '/z 2.3812 0.7008 0.7565 0.7588 0.8145 0.6428 0.6985 4.00
2 'h - 8 2.8851 1.0855 1.1375 1.1688 1.2208 1.0022 1.0542 4.75
- 8 3.5101
3 1.1480 1 .2000 1.231 3 1.2833 1.0647 1.1167 5.50
GENERAL NOTE:
On sizes '116 and '/e, the MXT and MN dimensions are shown out of relationship on the illustration
of step development.
NOTE:
(1) The dimensions given for steps at minimum thread and maximum thread are based on z/3 turn ( 0 . 6 6 6 7 ~from
) basic thread.
Actual truncation of the product thread may be slightly less than or slightly more than the tabulated truncation limit (ANSI
81.20.3) depending upon the variance from mean size in any given range (minimum range - basic range - maximum range).
Formulas are shown in Appendix C.
24
TABLE 12
in./in. -, 7
Example: 3/8-18 NPTF root check ring
of partial thread
Development - counterclockwise
TABLE 12 BASIC DIMENSIONS FOR ROOT CHECK RING GAGES
Minor Diam.
at L2 Length From Basic Pipe Min. Thread Max. Thread
End of Pipe. Thread [Note (111 [Note (111
Basic Thread
With Min. Min. Max. Min. Max. Min.
Truncation, Max. Width Truncation, Truncation, Truncation, Truncation, Truncation, Tru
D of Crest B BT MN MNT MX
at Minor
Nominal + 0.0002 Diam., + 0.002 + 0.002 +
Size - 0.0000 F f 0.001 - 0.000 f 0.001 - 0.000 f 0.001 -
'h6-27 0.2624 0.003 0.261 1 0.2066 0.2858 0.2313 0.2364 0.
'/a -27 0.3549 0.003 0.2639 0.2094 0.2886 0.2341 0.2392 0.
'/a - 1 8 0.4631 0.004 0.401 8 0.3467 0.4388 0.3837 0.3648 0.
'/a - 1 8 0.598 1 0.004 0.4078 0.3527 0.4448 0.3897 0.3708 0.
N
4
'12 -1 4 0.7385 0.004 0.5337 0.4766 0.5813 0.5242 0.4861 0
314 -1 4 0.9485 0.004 0.5457 0.4886 0.5933 0.5362 0.4981 0.
1 - 11 'h 1.1914 0.005 0.6828 0.5993 0.7408 0.6573 0.6248 0.
1 '14 - 1 1'/2 1.5364 0.005 0.7068 0.6233 0.7648 0.6813 0.6488 0.
GENERAL NOTE:
On sizes '/IS and '/a, the MX and MNT dimensions are shown out of relationship on the illustration of step development.
NOTE:
(1) The dimension given for steps at minimum thread and maximum thread are based on 2/i turn ( 0 . 6 6 6 7 ~ from
) basic thread.
Actual truncation of the product thread may be slightly less than or slightly more than the tabulated truncation limit (ANSI
B1.20.3) depending upon the variance from mean size in any given range (minimum range - basic range - maximum range).
Formulas are shown in AppendixC.
TABLE 13
4-Step Design
L, + 1 / 3 p (Step 3) Undercut optional - both designs
L , (ref.: no step)
tu
Q 9
\ /
k - 0 - */
1
L, - P (Step 1)
,a'
.Mark steps
I as shown L, - 1/3p (Step 2)
, L, + P (Step 4) Marking
shown
on shank of gage and
on handle
Example: 1/8-27 NPTF L ,
\. /. , I
/
\
'. /
/
T Small End
Basic Dimensions
at L , Plane T Min.
Min. Range
Max.
T Basic Range
Min. Max.
Max. Range
Min. Max
Major
Nominal Basic Pitch Diam., Pitch Major Step 1 Step 2 Step 2 Step 3 Step 3 Step
Size Length, Diam., Do Diam., Diam.
[Note 11)l L, L2 Eo [Note 1211 E, [Note (211 IL, - p) If, - %PI IL, - %p) :L, + %p) [L, + %P) ( L , +
%6-27 0.1600 0.261 13 0.271 18 0.29289 0.281 18 0.30289 0.12296 0.14766 0.14766 0.17234 0.17234 0.1970
'/a -27 0.1615 0.26385 0.36351 0.38522 0.37360 0.39531 0.12446 0.14916 0.14916 0.17384 0.17384 0.1985
'/4 -18 0.2278 0.401 78 0.47739 0.51339 0.49163 0.52763 0.17224 0.20928 0.20928 0.24632 0.24632 0.2833
3/a - 1 8 0.2400 0.40778 0.61201 0.64801 0.62701 0.66301 0.18444 0.22148 0.22148 0.25852 0.25852 0.2955
N
'/2 -14 0.3200 0.53371 0.75843 0.8081 5 0.77843 0.8281 5 0.24857 0.29619 0.29619 0.54381 0.34381 0.3914
'/4 -14 0.3390 0.54571 0.96768 1.01 740 0.98887 1.03859 0.26757 0.31519 0.31519 0.36281 0.36281 0.4104
1 -1 112' 0.4000 0.68278 1.21 363 1.23863 1.29829
1.27329 0.31304 0.37102 0.37 102 0.42898 0.42898 0.4869
1 '/4 - 1 1'/z 0.4200 0.70678 1.55713 1.61 679 1.58338 1.64304 0.33304 0.39102 0.39102 0.44898 0.44898 0.5069
1 '/z -1 1 '12 0.4200 0.72348 1.79609 1.85575 1.82234 1.88200 0.33304 0.39102 0.39 102 0.44898 0.44898 0.5069
-1 1 'h 0.43602 0.75652 2.26902 2.32868 2.29627 2.35593 0.34904 0.40702 0.40702 0.46498 0.46498 0.5229
2% - 8 0.6820 1.13750 2.71 953 2.80878 2.76216 2.85141 0.55700 0.64034 0.64034 0.72366 0.72366 0.8070
3 - 8 0.7660 1.20000 3.34062 3.42987 3.38850 3.47775 0.641 00 0.72434 0.72434 0.80766 0.80766 0.8910
GENERAL NOTE:
Gage blanks shall conform to dimensions given in ANSI 847.1,
NOTES:
(1) Notch formulas on drawing apply to all sizes.
(2) Major diameter is based on crest minimum truncation equal to maximum root truncation of product thread. (See 61.20.3)
> .
TABLE 14
3-Step Design
\
0
0
L , short + p (Note 1 ) 1,,- Basic step
\
Undercut optional
Remove convolution
of partial
Minimum
thread step
L , short - %p (Note 1)
TABLE 14 BASIC DIMENSIONS FOR L1 SHORT PLUG GAGES
Pitch
Small End T Min. Pitch Diam.
Gaging Step
Max. Pitch Diam.
Gaging Step T Basic Step
Pitch
Nominal Diam., Major (L, Short Pitch ( L , Short Pitch Diam., Major
Size L, Short L2 €0 Diam. (2) - %p) Diam. + PI Diam. E, Short Diam. (2)
lh6-27 0.12296 0.261 13 0.271 18 0.29289 0.1 0444 0.27771 0.16000 0.281 18 0.27886 0.30057
' %-27
1 0.12446 0.26385 0.36351 0.38522 0.10594 0.37013 0.16150 0.37360 0.371 28 0.39299
'/4 -1 8 0.17224 0.401 78 0.47739 0.51339 0.14446 0.48642 0.22780 0.491 63 0.4881 6
-1 8 0.18444 0.40778 0.61201 0.64801 0.15666 0.62180 0.24000 0.62701 0.62354 0.65954
-
w
1
'12
3/4
-1 4
-41
- 11 1/2
0.24857
0.26757
0.31 304
0.53371
0.54571
0.68278
0.75843
0.96768
1.21363
0.8081 5
1.01 740
1.27329
0.21286
0.23186
0.26956
0.771 74
0.9821 8
1.23048
0.32000
0.33900
0.40000
0.77843
0.98887
1.23863
0.77397
0.98441
1.23320
0.82369
1.0341 3
1.29286
0.33304 0.70678 1.5571 3 1.61 679 0.28956 1.57523 0.42000 1.58338 1.57794
1 '12 -1 11/2 (3) 0.33304 0.72348 1.79609 1.85575 0.28956 1.81419 0.42000 1.82234 1.81690 1.87656 1
2 -1 1'12 (3) 0.34904 0.75652 2.26902 2.32868 0.30556 2.28812 0.43600 2.29627 2.29084 2.35050
2 % - 8 (3) 0.55700 1.13750 2.71953 2.80878 0.49450 2.75044 0.68200 2.76216 2.75435 2.84360 2
3 - 8(3) 0.64 100 1.20000 3.34062 3.42987 0.57850 3.37678 0.76600 3.38850 3.38069 3.46994
GENERAL NOTES:
(a) Gage blanks shall conform t o dimensions given i n ANSI 847.1.
(b) Master gage same as NPTF shown in Table 21.
NOTES:
(1 I Maximum and minimum pitch diameter steps are gaging limits. Notch formulason drawing apply to all sizes
(2) Major diameter is based on crest minimum truncation
equal to maximum root truncation of product thread. (See ANSI B1.20.3)
(3) For reference only above 1-1 1% NPSF.
TABLE 15
3-Step Design
Maximum step
Undercut optional
Small End
Pitch
Diam., Major
Min. Pitch Diam.
Gaging Step
Pitch
Max. Pitch Diam.
Gaging Step
Pitch
r Pitch
Diam.,
Basic Step
Major
Nominal
Size Eo Diam. (2) (L, - 'hP) Diam. (L1 + p) Diam. E1 Diam. (2)
'he-27 0.1600 0.261 13 0.271 18 0.29289 0.14148 0.28002 0.19704 0.28350 0.281 18 0.30289
'/E -27 0.1615 0.26385 0.36351 0.38522 0.14298 0.37245 0.19854 0.37592 0.37360 0.39531
'h -1 8 0.2278 0.401 78 0.47739 0.51339 0.20002 0.48989 0.28336 0.4951 0 0.491 63 0.52763
/'E - 1 8 0.2400 0.40778 0.61201 0.64801 0.21 222 0.62527 0.29556 0.63048 0.62701 0.66301
112 -1 4 0.3200 0.5337 1 0.75843 0.80815 0.28428 0.77620 0.39143 0.78289 0.77843 0.8281 5
W '14 -1 4 0.3390 0.5457 1 0.96768 1.01 740 0.30328 0.98664 0.41043 0.99333 0.98887 1.03859
1 -1 1 '12 0.4000 0.68278 1.21 363 1.27329 0.35652 1.23592 0.48696 1.24406 1.23863 1.29829
1 1/4 -1 1 '12 (3) 0.4200 0.70678 1.55713 1.61679 0.37652 1.58066 0.50696 1.58882 1.58338 1.64304
'h
1 1/2 -1 1 (3) 0.4200 0.72348 1.79609 1.85575 0.37652 1.81 962 0.50696 1.82778 1.82234 1.88200
2 -1 1 (3) 'h 0.4360 0.75652 2.26902 2.32868 0.39252 2.29355 0.52296 2.301 70 1.29627 1.35593
2'h - 8 (3) 0.6820 1.13750 2.71 953 2.80878 0.61950 2.75825 0.80700 2.76997 2.7621 6 2.85141
3 - 8 (3) 0.7660 1.20000 3.34062 3.42987 0.70350 3.38459 0.89100 3.39631 3.38850 3.47775
GENERAL NOTES:
(a) Gage blanks shall conform to dimensions given in ANSI 847.1.
(b) Master gage same as NPTF shown in Table 21.
NOTES:
(1) Maximum and minimum pitch diameter steps are gaging limits. Notch formulason drawing apply to all sizes.
(2) Major diameter is based on crest minimum truncation 81.20.3)
equal to maximum root truncation of product thread. (See ANSI
(3) For reference only above 1-1 1'h NPSI.
ASME 81.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
c-- ---
I I I
!
f
al
34
T Small End
Relief T Min. Range T Basic Range T Max. Range T
Diam. Min. Max. Min. Max. Min. Max.
[Note (211
Major F Four Step 1 Step 2 Step 2 Step 3 Step 3 Step 4
Basic Pitch Diam. Threads
Nominal Length Diam., [Note (111 + 0.005 (L3 + p ) . (L, + L3 (L, + L3 (L, + L3 (L,+ L3 (L, + L3 (L, + L3
Size (L, + La) E3 D3 - 0.000 G - P) - %p) - 'hp) + 'hp) + 'hp) + P)
--
1/16-27 0.271 1 0.2642 0.281 5 0.216 0.1482 0.23406 0.25876 0.25876 0.28344 0.28344 0.30814
'/e -27 0.2726 0.3566 0.3738 0.309 0.1482 0.23556 0.26026 0.26026 0.28494 0.28494 0.30964
'14 - 18 0.3945 0.4670 0.4928 0.409 0.2222 0.33894 0.37598 0.37598 0.41 302 0.41 302 0.45006
- 18 0.4067 0.6016 0.6275 0.542 0.2222 0.351 14 0.38818 0.38818 0.42522 0.42522 0.46226
W
VI '12 -14 0.5343 0.7451 0.7783 0.676 0.2857 0.46287 0.51049 0.51049 0.5581 1 0.5581 1 0.60573
314 - 14 0.5533 0.9543 0.9876 0.886 0.2857 0.481 87 0.52949 0.52949 0.5771 1 0.5771 1 0.62473
1 -1 1 '12 0.6609 1.1 973 1.2379 1.118 0.3478 0.57394 0.63192 0.63192 0.68988 0.68988 0.74786
1'14 - 1 1 '12 0.6809 1.5408 1.5814 1.462 0.3478 0.59394 0.651 92 0.651 92 0.70988 0.70988 0.76786
1 '12 - 1 1 'h 0.6809 1.7798 1.8203 1.701 0.3478 0.59394 0.65192 0.651 92 0.70988 0.70988 0.76786
2 -1 1 '12 0.6969 2.2527 2.2932 2.174 0.3478 0.60994 0.66792 0.66792 0.72588 0.72588 0.78386
2 'h - 8 1.0570 2.6961 2.7543 2.590 0.5000 0.93200 1.01 534 1.01534 1.09866 1.09866 1.18200
3 - 8 1.1410 3.3172 3.3754 3.214 0.5000 1.01600 1.09934 1.09934 1.18266 1.18266 1.26600
GENERAL NOTE:
Gage blanks shall conform to dimensions given in ANSI B47.1.
NOTES:
(1) Major diameter is based on crest minimum truncation of 0 . 2 0 ~ .
+
(2) F = [E3 (0.0625 x 4/11 - sharp V thread height - 0.020 to 0.025 below sharp root]
(3) Notch formulas on drawing apply to all sizes.
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
3-Step Design
L 3 + L , short + p (Note 2)
I
I
/I
straiaht or convolution
erRemove convolution
of partial
thread -’ 1 I \ undercut
optional
with
1 Small End
Major
T Relief
Diam.
[Note (311,
F Four
Min. Pitch
Diam.
Gaging Step
Max. Pitch
Diam.
Gaging Step
Notch
Depth,
J
Pitch Diam. Threads, + 3 Threads + 3 Threads Blank
Nominal Diam., [Note (111. +0.005 (L, + PI, +
(L, L, Short +
(L, L, Short Length, + 0.005
Size €3 D3 - 0.000 G - %p) + P) I3 - 0.000
’h6-27 0.2642 0.281 5 0.216 0.1482 0.21 56 0.271 1 0.42 0.030
’/e -27 0.3566 0.3738 0.309 0.1482 0.2171 0.2726 0.46 0.030
’/4 - 18 0.4670 0.4928 0.2222 0.4090.31 11 0.3945 0.55 0.030
3/0 - 1 8 0.6016 0.6275 0.542 0.2222 0.3233 0.4067 0.62 0.030
1 ’/2 - 1 1‘12 1.7798 1.8203 1.701 0.3478 0.5504 0.6809 0.94 0.050
2 - 11 ‘12 2.2527 2.2932 2.174 0.3478 0.6969 0.56640.94 0.050
2‘h - 8 2.6961 2.7543 2.590 0.5000 0.8695 1.0570 1.58 0.050
3 - 8 3.31 72 3.3754 3.214 0.5000 1.1410 0.95351.58 0.050
GENERAL NOTE:
(a) Gage blanks shall conform t o dimensions given in ANSI 847.1.
(b) Master gage same as NPTF shown in Table 21.
NOTES:
(1) Major diameter is based on crest minimum truncation of 0 . 2 0 ~ .
(2) Maximum and minimum pitch diameterstep.s are gaging limits. Notch formulas on drawingapply to all sizes.
(3) F = [E, +
(0.0625 X 4p) - sharp V thread height - 0.020 to 0.025 below sharp root].
36
GAGING FOR DRYSEAL PIPE THREADS (INCH) ASME 01.20.5-1991
Taper 0.0625
+_0.0005 in./in.
Undercut
optional
on diameter
M X O T
-
\
[My3[
MN &- '-J
- - - - ~l
MN,
BJ -
shank
Marking
shown
on ofand
handle
on gage
Example: 1 /E-27 NPTF crest check plug
----
Development - counterclockwise
T T
I
Max. Diam.
at L,
Basic Thread
Basic Pipe Thread Min. Thread (1) Max. Thread ( 1 I
With Max. Min. Max. Min. Max. Min. Max.
Truncation, Truncation, Truncation, Truncation, Truncation, Truncation, Truncation,
D B BT MN MNT MX MXT Depth
of
Nominal + 0.00015 + 0.000 + 0.000 + 0.000 Notch,
Size - 0.00000 f 0.001 - 0.002 +0.001 - 0.002 +0.001 - 0.002 F
1 ' / z - 1 1'h 1.7149 0.6252 0.6809 0.5672 0.6229 0.6832 0.7389 0.120
2 - 11 '12 2.1878 0.641 2 0.6969 0.5832 0.6389 0.6992 0.7549 0.1 20
2'h - 8 (3) 2.6016 1.0050 1.0570 0.9217 0.9737 1.0883 0.120 1.1403
3 - 8 (3) 3.2227 1.0890 1.1410 1.0057 1.0577 1.1 723 0.120 1.2243
NOTES:
( 1 ) On sizes '116 and l/8, the MX and MN,dimensions are shown out of relationship on the illustration of step development.
(2) The dimensions given for steps at minimum thread and maximum thread are based on 2/3 turn ( 0 . 6 6 6 7 ~from ) basic thread.
less than or slightly more than the tabulated truncation limit(B1.20.3)
Actual truncation of the product thread may be slightly
depending upon the variance from mean size in any given range (minimum range - basic range - maximum range). Formulas
are shown in AppendixC.
(3) Gages are sizes 2Ih and 3 t o f i tstandard trilock handle.
37
ASME 81.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
Development - counterclockwise
Undercut optional
r1
i--1
L.-.J
MN
Removeconvolution of (See Table 6)
partial thread this end
Marking shown on shank of gage and on handle
Example: 1/8-27 NPTF root check plug
i
Max. Diam.
+
at L , L,
Length From
End of Fitting. Basic Pipe Thread Min. Thread (2) Max. Thread (2)
Basic Thread Depth
With Min. Max. Min. Max. Min. Max. Min. Max. of
Truncation, Width oi Truncation, Truncation, Truncation Truncation, Truncation Truncation, Notch,
D Crest at B 4 MN MNT MX M
MXT
Major
Nominal + 0.0002 Diam., + 0.002 + 0.002 + 0.002 + 0.005
Size - 0.0000 F f 0.001 - 0.000 *0.001 - 0.000 f 0.001 - 0.000 - 0.000
‘/16-27 0.2893 0.003 0.271 1 0.2166 0.2464 0.1919 0.2958 0.241 3 0.060
’/E -27 0.381 7 0.003 0.2726 0.2181 0.2479 0.1934 0.2973 0.2428 0.060
‘/4 - 1 8 0.5064 0.004 0.3945 0.3394 0.3575 0.3024 0.431 5 0.3764 0.080
3/E - 1 8 0.6410 0.004 0.4067 0.3516 0.3697 0.3146 0.4437 0.3886 0.080
‘12 - 1 4 0.7984 0.004 0.5343 0.4772 0.4867 0.4296 0.5819 0.5248 0.095
3/4 -1 4 1.0076 0.004 0.5533 0.4962 0.5057 0.4486 0.6009 0.5438 0.095
1 - 11 ‘12 1.2622 0.005 0.6609 0.5774 0.6029 0.5194 0.7189 0.6354 0.1 10
1 ‘/4 -1 1’12 1.6057 0.005 0.6809 0.5974 0.6229 0.5394 0.7389 0.6554 0.1 10
1 ‘12 - 1 1‘ h 1.8447 0.005 0.6809 0.5974 0.6229 0.5394 0.7389 0.6554 0.1 10
2 - 11 ‘12 2.31 76 0.005 0.6969 0.6134 0.6389 0.5554 0.7549 0.6714 0.1 10
2’12 - 8 (3) 2.7096 0.007 1.0570 0.9730 0.9737 0.8897 1.1403 1.0563 0.140
3 - 8 (3) 3.41 17 0.007 1.1410 1.0570 1.0577 0.9737 1.2243 1.1403 0.140
NOTES:
(1) On sizes ’116 and I h , the MXT and MN dimensions are shown out of relationship on the illustration of step development.
(2) The dimensions given for steps at minimum thread and maximum thread are based on 2/3 turn ( 0 . 6 6 6 7 ~from
) basic thread.
Actual truncation of the product thread may be slightly less than or slightly more than the tabulated truncation limit (ANSI
61.20.3) depending upon the variance from meansize in any given range (minimum range - basic range - maximum range).
Formulas are shown in AppendixC.
(3) Gages are sizes 2‘12 and 3 t o f i t standard trilock handle.
38
GAGING FOR DRYSEAL PIPE THREADS(INCH) ASME B1.20.5-1991
7
i
TABLE 20 BASIC DIMENSIONS OF MASTER RINGGAGES FOR
L , AND L3 TAPERPLUGGAGES
1 '12 - 1 1112 0.6809 1.82234 1.76442 1.77980 1.72188 3.06 2.25 0.28
2 - 1 1 112 0.6969 2.29627 2.25270 2.19479
2.23836 3.62 2.75 0.30
2 'h - 8 1.0570 2.76216 2.67891 2.69610 2.61 285 4.25 3.38 0.50
3 - 8 1.1410 3.38850 3.30525 3.31 720 3.23395 5.00 4.00 0.56
NOTE:
(1) Minor diameter of master ring gages based on truncation of 0 . 1 to
~ clear maximum crest truncation of product thread (flank
wear plane on working plug gage).
39
ASME 81.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
w . -'
Remove convolution of
-
partial thread both ends
I
Major
Diam.
Pitch
Diam.,
Gaging Notch
Major
Diam.
Pitch
Diam.,
Large End
Major
Size (L, + LB) E3 [Note (111 E1 [Note (111 E2 Diam.
1 '/2 - 1 1'12 0.6809 0.98436 1.7798 1.83771 1.82234 1.8ao25 1,84130 1.89922
2 - 11 112 0.6969 1.01 740 2.2527 2.31061 2.29627 2.35418 2.31630 2.37422
2 ~ -2 a 1.0570 2.6961 1.512.77935
250 2.7621 6 2.84541 2.79062 2.87388
3 - 8 1.1410 1.57500 3..3172 3.40045 3.38850 3.471 75 3.49888 3.41 562
NOTE:
.- -
(1) Major diameter of master plug gages based on truncation of 0 . 1 t~o clear maximum crest truncationof product thread (flank
wear plane on working ring gages).
.,
40
GAGING FOR DRYSEAL PIPE THREADS (INCH) ASME B1.20.5-1991
r D2
Nominal L D,
f 0.00005
DO
Ref.
Nominal
Size f 0.001
D3
f0.00005
D,
Ref.
I
1 1/2 - 1 1'12 0.7235 1.9062 1.8610 1 '12 - 1 1'/2 0.6809 1.7149 1.7575
2 - 11 '12 0.7565 2.381 2 2.3339 2 - 1 1 '12 0.6969 2.1878 2.2314
2 '/2 - 8 1.1375 2.8851 2.8140 2 '12 - 8 1.0570 2.601 6 2.6677
3 - 8 1,2000 3.5101 3.4351 3 - 8 1.1410 3.2227 3.2940
GENERAL NOTES:
(a) Tolerance on taper on master plug gages over basic length ( L 2 )is minus 0.0001 5and tolerance on taper on master ring gages
over basic length ( L , + L,) is plus 0.0001 5.
(b) Master plugs and master rings on this tabulation do not mate one to the other and each must be calibrated and certified
separately by gage manufacturer or qualified metrology laboratory.
(c) Standoff of master plug gage t o working 6-step crest ringgage will be flush to +0.004 at the B r step.
(dl Standoff of master ringgage to working 6-step crest pluggage will be flush to-0.004 at the B r step.
41
ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS (INCH)
r O2
L ,-4 L Mark
handle
and
member
1 1/2 - 1 1 '/2 0.7235 1.7764 1.731 2 1 1/2 - 1 1112 0.6809 1.8447 1.8873
2 - 1 1 112 0.7565 2.2514 2.2041 2 - 1 1 1/2 0.6969 2.3176 2.361 2
2 12' - 8 1.1375 2.6961 2.6250 2 '/2 - 8 1.0570 . 2.7096 2.7757
3 - 8 1.2000 3.321 1 3.2461 3 - 8 1.1410 3.41 17 3.4830
GENERAL NOTES:
(a) Tolerance on taper on master plug gages over basic length( L Z ) is minus 0.0001 5 and tolerance on taper on master ring gages
over basic length ( L , +-L,) is plus 0.0001 5.
(b) Master plugs and master rings on this tabulation do not mate one to the other and each must be calibrated and certified
separately by gage manufacturer or qualified metrology laboratory.
(c) Standoff of master plug gage to working 6-step root ring gage willbe flush to -10.004 at the B step. '
(d) Standoff of master ring gage to working 6-step root plug gage willbe flush to +0.004 at the B step.
42
APPENDIX A
3-STEP GAGES FOR CHECKING NPTF THREADS
(This Appendix is not part of ASME B1.20.5-1991and is included for information purposes only.)
A I .I L1 Ring Gage
See Table A1 .
A I .2 L2 Ring Gage
See Table A2.
A I .4 L3 Plug Gage
See Table A4.
43
Mark ring with size and type
Remove convolution
of partial thread
T
~~
'/'E.-27 0.1600 0.12296 0.1 9704 0.281 18 0.25947 0.271 18 0.24947 0.38
' / E -27 0.1615 0.12446 0.1 9854 0.37360 0.35189 0.36351 0.34180 0.47
'/4 - 1 8 0.2278 0.17224 0.28336 0.491 63 0.45563 0.47739 0.441 39 0.59
-1 8 0.2400 0.18444 0.29556 0.62701 0.59101 0.61 201 0.57601 0.72
1 1/2 - 1 1112 0.4200 0.33304 0.50696 1.82234 1.76268 1.79609 1.73643 1.94
2 - 11 ' / 2 0.4360 0.34904 0.52296 2.29627 2.23661 2.26902 2.20936 2.50
2 '1'2 - 8 0.6820 0.55700 0.80700 2.76216 2.67291 2.71953 2.63028 2.94
3 - 8 0.7660 0.64100 0.89100 3.38850 3.29925 3.34062 3.25137 3.56
GENERAL NOTES:
(a) Gage blanks shall conform to dimensions given in ANSI 847.1 except for extra width of 3-step design.
(b) Use of gages having minor diameters based on crest truncations equal to 0 . 2 0 ~to 0 . 2 5 ~is not prohibited, but such gages
should be replaced by gages having specified minor diameters as soon as practicable.
NOTE:
( 11 Minor diameter isbased on crest minimum truncationequal t o maximum root truncationof product thread. (See ANSI B1.20.3)
44
Mark ring with size and type
Example: 1/8-27 NPTF L2
Remove convolution
of partial thread
this end
7
- E2
-L2-P
Bottom (Small End)
View of Gage - L2
TABLE A 2 BASIC
DIMEN ISIONS FOR L, 3-STEP RINGGAGES
Large End Small End
Basic Max. Min.
Gaging Gaging Gaging Pitch Minor Pitch Minor Counterbore
Nominal Step. Step Step Diam., Diam. Diam ., Diam. Diam.,
Size L2 (L2 - P ) (L2 + P ) €2 [Note ( 1)I E. [Note (111 (L,) 8
‘h6-27 0.261 1 3 0.22409 0.2981 7 0.28750 0.27024 0.27886 0.26160 0.1600 0.38
‘/a -27 0.26385 0.22681 0.30089 0.38000 0.36274 0.371 29 0.35403 0.1615 0.47
‘/4 - 18 0.45734
0.34622 0.401 78 0.47661 0.50250
0.4881 6 0.46227 0.59 0.2278
Ya - 18 0.46334
0.35222 0.40778 0.63750 0.61 161 0.62354 0.59765 0.72 0.2400
‘/2 -1 4 0.53371 0.46228 0.60514 0.791 79 0.75850 0.77396 0.74067 0.3200 0.88
3/4 -1 4 0.54571 0.47428 0.61714 1.001 79 0.96850 0.98440 0.951 11 0.3390 1.09
1 - 11 ’/2 0.59582 0.76974
0.68278 1.21 577 1.23320
1.25630 1.19267 1.34 0.4000
1 ‘14 - 1 1‘12 0.61982 0.70678
0.79374 1.57794
1.56077 1.60130 1.53741 1.69 0.4200
1 ‘12 - 1 1 ‘h 0.72348 0.63652 0.81 044 1.841 30 1.80077 1.81 690 1.77637 0.4200 1.94
2 - 11 112 0.75652 0.66956 0.84348 2.31630 2.27577 2.29084 2.25031 2.50 0.4360
2 ’12 - 8 1.01 250 1.26250
1.13750 2.73237 2.79062
2.75434 2.89609 2.94 0.6820
3 - 8 1.20000 1.07500 1.32500 3.35737 3.41 562
3.38068 3.32243 3.56 0.7660
GENERAL NOTE:
Gage blanks shall conform to dimensions given in ANSI 847.1 except for extra width of 3-stepdesign.
NOTE:
(1) Minor diameter is based on crest minimum truncation of 0 . 2 0 ~ .
45
TABLE A 3
El
Undercut optional
Remove convolution
Minimum of partial
thread step
L, - p (Note 1 )
TABLE A 3 BASIC DIMENSIONS FOR L1 3-STEP PLUG GAGES,NPTF
Nominal
T Pitch
Diam.,
Small End
Major
Diam.
Min. Pitch
Diam.
Gaging Step
Pitch
T Max. Pitch
Diam.
Gaging Step
Pitch
Basic Step
Pitch Major
T
Diam., Diam.
Size L, EO [Note (211 (Ll - p) Diam. (L, + p) Diam. El [Note (211
'116-27 0.1 600 0.261 13 0.27 1 18 0.29289 0.12296 0.27886 0.19704 0.28350 0.281 18 0.30289 0
'/a -27 0.1615 0.26385 0.36351 0.38522 0.12446 0.371 29 0.19854 0.37592 0.37360 0.39531 0
'/a - 18 0.2278 0.401 78 0.47739 0.51339 0.1 7224 0.488 16 0.28336 0.49510 0.491 63 0.52763 0
E
/' - 18 0.2400 0.40778 0.61 201 0.64801 0.18444 0.62354 0.29556 0.63048 0.62701 0.66301 0
112 - 14 0.3200 0.53371 0.75843 0.8081 5 0.24857 0.77397 0.39143 0.78289 0.77843 0.8281 5 0
3/4 - 14 0.3390 0.54571 0.96768 1.01 740 0.26757 0.98441 0.41043 0.99333 0.98887 1.03859 1
1 - 11 1/2 0.4000 0.68278 1.21363 1.27329 0.31304 1.23320 0.48696 1.24406 1.23863 1.29829 1
1 '/4 - 1 1'/z 0.4200 0.70678 1.55713 1.61679 0.33304 1.57795 0.50696 1.58882 1.58338 1.64304 1
1 '/z - 1 1 '/z 0.4200 0.72348 1.79609 1.85575 0.33304 1.81691 1.82234 1.88200 1
2 - 11 '12 0.4360 0.75652 2.26902 2.32868 0.34904 2.29084 1.29627 1.35593 2
2 '12 - 8 0.6820 1.13750 2.71953 2.80878 0.55700 2.75435 2.76216 2.85141 2
3 - 8 0.7660 1.20000 3.34062 3.42987 0.64100 3.38069 3.38850 3.47775 3
GENERAL NOTE:
Gage blanks shall conform todimensions given in ANSI647.1.
NOTES:
(1) Maximum and minimum pitch diameter stepsare gaging limits. Notch formulas on drawingapply to all sizes.
(2) Major diameter is based on crest minimum truncation equal to maximum root truncation of product thread, (See ANSI B1.20.3)
Marking shown on shank of gage and on handle
\
Example: 1/8-27 NPTF L,
L3 + L1 + p (Note 1)
L3 + L, ,-- Basic step
Remove convolution of partial thread ' Taper or straight with undercut optional
T Small End
Major
Relief
Diam.,
F
Four
Min. Pitch
Diam.
Min. Pitch
Diam.
Notch
Depth,
[Note (2)l J
Pitch Diam., Threads Gaging Step Gaging Step Blank
Nominal Diam., 0 3 + 0.005 (L3 + PI. + 3 Threads + 3 Threads Length, + 0.005
Size €3 [Note 1311 - 0.000 G (L3 + L, - P) ( L p + Lq + P ) B - 0.000
'/16-27 0.2642 0.281 5 0.21 6 0.1482 0.2341 0.3082 0.42 0.030
'/E -27 0.3566 0.3738 0.309 0.1482 0.2356 0.3097 0.030 0.46
'/4 - 18 0.4670 0.4928 0.409 0.2222 0.3389 0.4500 0.55 0.030
% -1 8 0.601 6 0.6275 0.542 0.2222 0.351 1 0.4622 0.62 0.030
1 '/2 - 1 1'/2 1.7798 1.8203 1.701 0.3478 0.5939 0.7678 0.94 0.050
2 - 11 '12 2.2527 2.2932 2.1 74 0.3478 0.6099 0.7838 0.94 0.050
2 '12 - 8 2.6961 2.7543 2.590 0.5000 0.9320 1.1820 1.58 0.050
3 - 8 3.31 72 3.3754 3.214 0.5000 1.0160. 1.2660 1.58 0.050
GENERAL NOTE:
Gage blanks shall conform to dimensions given in ANSI B47.1.
NOTES:
(1) Maximum and minimum pitch diameter steps are gaging limits. Notch formulas on drawing apply to all sizes.
+
(2) F = [E3 (0.0625 x 4p) - sharp V thread height - 0.020 to 0.025 below sharp root]
(3) Major diameter is based on crest minimum truncation of 0 . 2 0 ~ .
48
APPENDIX B
MEASUREMENT OF PITCHDIAMETER OF TAPERTHREADS HAVING AN
INCLUDED TAPER OF 0.0625 INCH PER INCH
(This Appendix is not part of ASME B1.20.5-1991 and is included for information purposes only.)
49
Prussian blue
Line of measurement
for 60 deg. threads may be used. This simplified for- such cases pitch diameter measurement is made in the
mula (3) gives a value of E that is 0.00005 in. larger usual horizontal manner, but care must be taken that the
than that given by the above general formula (1) for the measuring contacts touch all three wires, as the line of
2 '12-8 American National Standard taper pipe thread, the measurement is not perpendicular to the axis of the screw
worst case in this thread series. when there is proper contact. Figure B2 shows the hor-
The pitch diameterat any other point along the thread, izontal measuring method using a sine block to tilt the
as at the gaging notch, is obtained by multiplying the taper plug gage.
distance parallel to the axis of the thread, between this On account of this inclination, the measured distance
point and the point at which the measurement was taken, between the axes of the wires must be multiplied by the
by the taper per inch, then adding the product to or sub- secant of the half angle-of the taper of the thread. The
tracting it from the measured pitch diameter according formula for the pitch diameter,at the marked gage point
to the direction in which the second point is located with of any taper thread plug gage, the threads of which are.
respect to the first. symmetrical with respect to a line perpendicular to the
axis, then has the form:
4
B1.3 Three-Wire
Methods E = (M,- w) sec p + LJ(cot
~
2
- w cosec a (4)
B1.3.1 Horizontal Measurement. It is sometimes
convenient to use three wires when the plane at the small in which /3 = half angle of taper of thread. Thus the
endof the gage is perpendicular to the thread axis. Inpitch diameter of an American National Standard pipe
50
Mark with
Prussian blue
taper thread gage having correct angle (60 deg.) and time required when the pitch diameter of a number of
taper (0.0625 in./in.) is then given by the formula gages of the same size is to be measured. Gages as large
as 3 in. nominal size can be measured by this method,
E = 1.OOO49(M,- W) + 0.86603p - 2~ (5) see Fig. B3. The gage is supported on two wires placed
several threads apart, which are in turn supported on a
The pitch diameter at any other point along the thread, taper thread testing fixture. The third wire is placed in
as at the gaging notch, is obtained by multiplying the the threads at the top of the gage and measurement is
distance parallel to the axis of the thread, between this made from the top of this wire to the bottom of the fix-
point andthe point at whichthe measurement was taken, ture with a vertical comparator having a flat anvil, using
by the taper per inch, then adding the product to or sub- a gage block combination as the standard. The fixture
tracting it from the measured pitch diameter according consists of a block, the upper surface of which is at an
to the direction in which the second point is located with angle to the base plane equal to the nominal angle of
respect to the first. taper of the thread, 20. Thus the element of the cone at
the top of the thread gage is made parallel to the base
of the instrument. The direction of measurement is not
B1.3.2 Vertical Measurement. An adaptation of perpendicular to the axis of the gage but at an angle, 0,
the three-wire method is frequently used to reduce the from perpendicularity. A stop is provided at the thick
51
FIG. 83 VERTICAL MEASUREMENT OF PITCH DIAMETER OFTAPER GAGES BY
THE 3-WIREMETHOD USING A SINE FIXTURE
end of the block with respect to which the gage is posi- diameters, the rolls of each pair being equal in diameter.
tioned on the fixture. As the plane of the end of the gage Two measurements, M , and M,, are made over the rolls
maynot be perpendicular to the axis, a roll approxi- and formulas are applied as follows:
mately equal to the diameter of the gage should be in-
serted between the stop and the gage to assure contact
at the axis of the gage. For a given fixture and roll, a
cot
90 deg. - 6 - M2 - M i
-
+ d , - d2
constant, k , is computed which, when subtracted from (6)
2 d2 - dl
the measured distance Mwc from the top of the upper
wire to the base plane gives M , corresponding to the
pitch diameter, E,, at the small end of the gage.
90 deg. -
- 2g sec 6 (7)
M , = M,, - k 2
52
methods described, on account of elastic deformations B2 MEASUREMENT OF PITCH DIAMETER OF
of the rolls and gage blocks under the measuring force, TAPER THREAD RING GAGE
and differing conditions of loading of the thread wires.
B2.1 Common Method
The usual practice is to fit the ring gage to a threaded
setting plug rather than measure the pitch diameter.
B1.4.2 Measurement E at the Marked Gage When the thread ring gage is of correct lead, angle, and
Point. A four-wire method of measurement that gives thread form, within close limits, this method is satisfac-
pitch diameter at the gage point is illustrated in Fig. B5. tory. It is the only method available for small sizes of
A pair of gage blocks are chosen to support the two rolls threads. For the larger sizes, a direct method of mea-
d3 so that L is equal to the sum of the gage block stack surement of pitch diameter is made on an XYZ coordi-
and the radius of the roll. For a taper of 0.0625 in./in. nate measuring machine.
the simple pitch diameter equation (3) becomes
62.2 Ball Probe Method
The pitch diameter of taper thread ring gage may be
determined by comparison with an external standard 60
when M3 = measurement over rolls d3. deg. zero lead groove ground into a plain cylinder as
53
FIG. B5 MEASUREMENT OF PITCH DIAMETER E,,, OF TAPER
THREAD GAGES BY THE 4-WIRE METHOD
shown in Fig. B6. The groove standard is calibrated for Where X, is the measured distance between left side of
a pitch diameter with the “best-size” pair of wires for the 60 deg. groove standard and the right side of the
therequired pitch by the methodused for external thread, X, is the measured distance between the right
straight threads. A double-ended stylus with the ends side of the groove standard, and the average value of
radiused to match the “best-size’’ wire is used with a the left side of the corresponding internal threads and
null indicator to obtain two readings (R, and R,) on the Estd is thecalibrated pitch diameter of the 60 deg. groove
standard and three readings (R2, R;, and R;) on the in-
standard.
ternal taper thread (See Fig. B6). The standard and the
The pitch diameter at any other point along the thread
ring gage are mounted separately on the table on an XYZ
coordinate measuring machine. From the five position is obtained by multiplying the distance parallel to the
readings the internal pitch diameter, E,, is calculated: axis of the thread, between this point and the point at
which the measurement wastaken, by the taper per inch,
Em = X, + X, - Esrd . (9) then applying the product to E,.
54
FIG. B6 MEASUREMENT OF PITCHDIAMETER OF TAPER THREAD RINGGAGE ON
COORDINATEMEASURINGMACHINEWITH BALLPROBE
Intentionally left blank
APPENDIX C
FORMULAS FOR CALCULATING6-STEP TAPER PLUG AND RINGGAGE DIMENSIONS
0 . 6 6 6 7 ~= 0.0476
57
Intentionally left blank
APPENDIX D
THETURNSENGAGEMENTMETHOD OF GAGINGPRODUCTTHREADS
diameter size at the small end of the gage is the same in '/16-27 3.32 5.80 3.82 6.57
both cases and the step location is not used. '/e -27 3.36 5.87 3.86 6.61
'/4 - 18 3.10 5.98 3.60 6.35
3 / ~- 1 8 3.32 6.09 3.82 6.57
59
Intentionally left blank
Intentionally left blank