Sheet Metal Design Guide - 2021 Update - Geomiq

Download as pdf or txt
Download as pdf or txt
You are on page 1of 34

T. 020 3962 9020 E. support@geomiq.

com

 Sign in

SHEET METAL FABRICATION DESIGN GUIDE


The fundamentals of Sheet Metal

GET A QUOTE NOW

QUICK GUIDE
Find what you’re looking for.

 Sheet Metal Introduction 

 Forming Basics 

 Laser Cutting 

 Tolerances 

 Features 
SHEET METAL INTRODUCTION
These basic guidelines for sheet metal fabrication include important design
considerations to
help improve part manufacturability, enhance cosmetic appearance,
and reduce overall
production time.
Basic Principles
Sheet Metal Fabrication is the process of forming parts from a metal sheet by punching,
cutting, stamping, and bending. 

3D CAD files are converted into machine code, which controls a machine to precisely cut and
form the sheets into the final part. 

Sheet metal parts are known for their durability, which makes them great for end
use applications (e.g. chassis). Parts used for low volume prototypes, and high volume
production runs are most cost-effective due to large initial setup and material costs. 

Because parts are formed from a single sheet of metal, designs must maintain a uniform
thickness. Be sure to follow the design requirements and tolerances to ensure parts fall
closer to design intent and cutting sheets of metal 

FORMING BASICS
Bending
Bending is a process whereby a force is applied to sheet metal which causes it to bend at an
angle and form the desired shape. Bends can be short or long depending on

what the design requires. 

Bending is performed by a press brake machine that can be automatically or manually


loaded. Press brakes are available in a variety of different sizes and lengths (20-200 tons)
depending on the process requirements.
The press brake contains an upper tool called the punch and lower tool called the die
between which the sheet metal is placed. 

The sheet is placed between the two and held in place by the backstop. The bend angle is
determined by the depth that the punch forces the sheet into the die. This depth is precisely
controlled to achieve the required bend. 
q

Standard tooling is usually used for the punch and die. Tooling material includes, in order of
increasing strength, hardwood, low carbon steel, tool steel and carbide steel.

Parts to be bent are supplied as flat patterns with bending information. Sometimes bend
positions are etched with bend notches, or these notches can be cut out to show the
benders where to bend. 

Once the laser has cut the flat parts out they can be sent for bending. A press brake forms
the flat pattern into a bent part.
Critical Dimensions
The following are some terminology that are used in sheet metal. Designers need to adhere
to machinery guidelines when designing for bending. Bends can be characterised by these
parameters. Some critical dimensions that need to be considered when setting up sheet
metal in CAD software are sheet metal thickness, the k-factor and bend radius. One needs to
h k th t th f t i t t ith th t li th t ill b di f t i
check that these factors are consistent with the tooling that will be used in manufacturing.
This guide gives important guidelines for good design practice.

Bend line– The straight line on the surface of the sheet, on either side of the bend, that
defines he end of the level flange and the start of the bend.

Bend radius – The distance from the bend axis to the inside surface of the material, between
the bend lines.

Bend angle – The angle of the bend, measured between the bent flange and its original
position, or as the included angle between perpendicular lines drawn from the bend
lines.Sometimes specified as the inside bend radius. The outside bend radius is equal to the
inside bend radius plus the sheet thickness.

Neutral axis – The location in the sheet that is neither stretched nor compressed, and
therefore remains at a constant length.

K-factor – The location of the neutral axis in the material, calculated as the ratio of the
distance of the neutral axis T, to the material thickness t. The K-factor is dependent upon
several factors (material, bending operation, bend angle, etc.) and is greater than 0.25, but
cannot exceed 0.50. K factor = T/t

Bend allowance The length of the neutral axis between the bend lines or the arc length of
Bend allowance – The length of the neutral axis between the bend lines or the arc length of
the bend. The bend allowance added to the flange lengths is equal to the total flat length.

K-Factor
The K-factor is the ratio between the the neutral axis to the thickness of the material.

Importance of the K-factor in sheet metal design

The K-factor is used to calculate flat patterns because it is related to how much material is
stretched during bending. Therefore it is important to have the value correct in CAD
software. The value of the K-factor should range between 0 – 0,5. To be more exact the K-
factor can be calculated taking the average of 3 samples from bent parts and plugging the
measurements of bend allowance, bend angle, material thickness and inner radius into the
following formula:

Some basic K-factor values are shown here. Use these as a guideline.

K-factor chart

Radius Soft / Aluminum Medium / Steel Hard / Stainless Steel

Air Bending

0-t .33 .38 .40

t. - 3*t .40 .43 .45

3*t. - >3*t. .50 .50 .50

Bottom Bending
0 - t. .42 .44 .46
K-factor chart
t. - 3*t. .46 .47 .48

3*t. - >3*t. .50 .50 .50

Wall Thickness
Parts need to maintain a uniform wall thickness throughout. Generally capabilities of of
0,9mm – 20mm in thickness are able to be manufactured from sheet (<3mm) or plate
(>3mm) but this tolerance depends mainly on the part.

When considering sheet metal thickness, a single sheet with punches (holes) is a good rule
of thumb. Some features such as countersinks are doable but counter bores and other
machined features are difficult to produce as they require post machining.
BENDING
Bend Radius
Sheet metal bend brakes are used to bend material into the parts desired geometry. Bends
that are in the same plane need to be designed in the same direction to avoid part re
orientation, to save both money and time.

Keeping the bend radius consistent will also make parts more cost-effective. Thick parts
tend to become inaccurate so they should be avoided if possible. Small bends to large.
Consistent Orientation

Inconsistent Orientation
Springback

When bending a piece of sheet metal, the residual stresses in the material will cause the
sheet to springback slightly after the bending operation. Due to this elastic recovery, it is
necessary to over-bend the sheet a precise amount to achieve the desired bend radius and
bend angle. The final bend radius will be greater than initially formed and the final bend
angle will be smaller. The ratio of the final bend angle to the initial bend angle is defined as
the springback factor, KS. The amount of springback depends upon several factors, including
the material, bending operation, and the initial bend angle and bend radius.

Dimensions:

To prevent parts from fracturing or having distortions, make sure to keep the inside bend
radius at least equal to the material thickness 

Bend Angles:

A +/- 1 degree tolerance on all bend angles is generally acceptable in the industry. Flange
length must be at least 4 times the material thickness.

Rule of thumb

It is recommended to use the same radii across all bends, and flange length must be at least
4 times the material thickness.

Minimumbend, r
Minimum bend radii requirements can vary depending on applications and material. For
aerospace and space applications, the values may be higher. When the radius is less than
recommended, this can cause material flow problems in soft material and fracturing in hard
material. Localised necking or fracture may also occur in such cases. It is recommended that
minimum inner bend radius should be at least 1 times material thickness.

Minimumflange Lenght, b
This is the minimum length of the The bend must be supported all the way until the bend is
complete the flange must be long enough to reach the top of the die after it’s been fully
formed. Brake press operators should know the minimum flange lengths for their tooling
before attempting bends that may not work and while it is possible to calculate the minimum
flange having an Air Bend Force Chart on hand certainly makes it more convenient.
Material Thickness, t

The thickness of the material is not proportional to the tonnage like the v opening. Doubling
the thickness does not mean doubling the tonnage. Instead the bending force is related by
the square of the thickness. What this means is that if the material thickness is doubled the
tonnage required increases 4 fold.

Work Piece Length, L

Like the v opening the tonnage required is directly related to the length of the work piece.
Doubling the work length means doubling the required tonnage. It should be noted that
when bending short pieces, under 3” in length, the tonnage required may be less than that
which is proportional to its length. Knowing this can prevent damaging a die.

Air Force Bending Chart

The Air Force Bending chart is a chart showing the tonnage used for bending different
thickness sheet metal. It is useful for sheet metal designers as it specifies the bend radius
and tooling to be used for different thicknesses. It is shown here for mild steel. Designers
can use this as a guide when designing the minimum flange length possible with the
tooling for different V blocks as well as the bend radius. The following charts are based on
the Armada Air Force bend guide.
Download pdf

Bend Relief
When a bend is made close to an edge the material may tear unless bend relief is given.

Bend 1 shows a a tear relief.

Bend 2 shows a rectangular relief cut into the part, the depth of the relief should be greater
than the radius of the bend. The width of the relief should be the material thickness or
greater.
Bend reliefs are utilised where a bend extends on an edge. The relief notch is added to
prevent tearing. Bend reliefs will be no deeper than the material thickness plus the bend
radius.

Bend Height
Bend height Sheetmetal bend height should be at least twice the thickness of the sheetmetal
plus the bend radius
H=2t + r

If the bend height is too small this will result in deformation and low bending quality.

Forming Near Holes


When a bend is made too close to a hole the hole may become deformed. Hole 1 shows a
hole that has become teardrop shaped because of this problem.

To save the cost of punching or drilling in a secondary operation the following formulas can
be used to calculate the minimum distance required:

For a slot or hole < 25mm in diameter the minimum distance to Hole 2 centre:

D = 2t + r

As a rule of thumb the distance from the outside of the material to the bottom of the cutout
should be equal to the minimum flange length as prescribed by the air bend force chart

D = 2,5t + r
When using a punch press, or laser cutting, holes should never be less than that of the
material thickness.

Minimum Distance from extruded hole to part edge


Extruding metal is one of the most extreme pressure applications in press working and
generates lot of friction and heat. If an extruded hole is too close to the part edge, it can lead
to deformation or tearing of the metal. It is recommended that the minimum distance
between the extruded holes to part edge should be at least three times the thickness of
sheet.
Minimum Distance Between Extruded Holes

Certain distance should be maintained between two extruded holes in sheet metal designs.
If extruded holes are too close it can lead to metal deformation. It is recommended that the
minimum distance between two extruded holes should be six times the thickness of sheet
metal.

Minimum Hole Diameter


The diameter of the hole in sheet metal part should not be very small, small holes are created
by piercing operation and for manufacture small holes, small sizes punches are required.
Small hole size in sheet metal requires smaller size punching tool which may leads to break
during the operation. It is recommended that the diameter of the hole should be equal or
more than the thickness of the sheet metal.
LASER CUTTING
Laser cutting is a type of production that uses a laser to cut different metals. The laser has a
high energy beam which easily burns through the material. Laser cutting can be used on
materials such as metal, aluminium, plastic, wood, rubber, etc. Lasers use computer
numerically controlled programming (CNC) to determine the shape and position ls of the
cutouts. Material thicknesses of up to 20mm can be lasercut. There are advantages and
disadvantages in using lasercutting. CO2 lasers are more traditional, and can cut thicker
materials but do not deliver such an accurate cut as fibre lasers. Fibre lasers can generally
cut thinner materials and have much higher cutting speeds than CO2 .

Advantages and Disadvantages

Advantages of lasercutting over cutting mechanically include better workholding, reduced


workpiece contamination, better precision and reduced chance of warping as the heat
affected zone is small. Some disadvantages are that lasercutting does not always cut well
with some materials (for example not all aluminium) and it is not always consistent. Despite
the disadvantages lasercutting is highly efficient and cost effective.
Tolerances
General Tolerances

If a drawing or specification sheet has not been provided by the customer, we will
manufacture the product from the model to the specifications listed here. Sharp edges will
be broken and deburred by default. Critical edges that must be left sharp should be noted
and specified on a print.

Tolerances

Forming and Bending: +/- 0,4 mm

Bend to hole or feature: +/- 0,2 mm

Linear dimensions excluding locations to bends +/- 0,1 mm

Diameters with inserts +/- 0,06 mm

Angularity +/- 2 degrees

Surface roughness +/- 3,2 micrometers

Material Restrictions

Materials that are not suitable for lasercutting include mirrored or reflective materials,
Masonite boards, composites containing PVC.

Acceptable Materials

Generally the following materials are suitable for lasercutting: metal, stainless steel, some
thicknesses of aluminium, wood and some plastics.

Localized hardening

Localised hardening takes place on the edges where the where the laser has cut. This
hardening produces a durable and smooth edge without the need for finishing after using
the laser cutter
Distortion

A heat-affected zone (HAZ) is produced during laser cutting . In carbon steel, the higher the
hardenability, the greater the HAZ. Distortion from laser processing is a result of the sudden
rise in temperature of the material near the cutting zone. Distortion is also created by the
rapid solidification of the cutting zone. In addition, distortion also can be attributed to the
rapid solidification of material remaining on the sides of the cut.

Kerf
During laser cutting a portion of the material is burnt away when the laser cuts through,
leaving a small gap. This ‘gap’ is known as the laser kerf and ranges from 0.08 – 0.45mm
depending on the material type, thickness and other conditional factors. A minimum distance
of 1-2mm between parts needs to be left to avoid accidental crossover cutting. 

It is also advised to keep parts 2-5mm away from the edge of the material due to some
sheets being warped or slightly off in their sizing. One should always cut parts in the
boundary of the sheet size and not use the sheet edges as a border.
TOLERANCES
Wall Thickness

Because Sheet Metal parts are manufactured from a single sheet of metal the part must
maintain a uniform wall thickness. Sheet metal parts with a minimum of 0.9mm to 20mm in
thickness can be manufactured.

Hole Diameter

When designing parts for laser cutting one should not make holes smaller than the thickness
of the material.

Bends

Bends in sheet metal are manufactured using sheet metal brakes. A +/- 1 degree tolerance
on all bend angles. Other standard bend radii available, some of which will add additional
cost to your part, include:

0.9mm – 1.2mm

1.8mm – 2.4mm

3.8mm – 5.0mm

7.5mm – 10mm

15mm – 20mm

Curls
Curl Feature Guidelines

Curling sheet metal is the process of adding a hollow, circular roll to the edge of the sheet.
The curled edge

provides strength to the edge and makes it safe for handling. Curls are most often used to
remove a sharp

untreated edge and make it safe for handling. It is recommended that: The outside radius of
a curl should not be smaller than 2 times the material thickness. 
A size of the hole should be at least the radius of the curl plus material thickness from the
curl feature. A bend should be at least the radius of the curl plus 6 times the material
thickness from the curl feature

Countersink Holes
Machined and formed countersinks are possible after lasercutting. Machined counter sinks
are created with a drill press while formed counter sinks are created with punch press
tooling. Countersink depths should me no more than 0,6mm the material thickness.
Countersink Tolerance
Countersink Tolerances:

Both machined and formed countersinks are available-conical holes cut into a manufactured
object allowing a screw, nail, or bolt to be inserted flush with the surface. We recommend
the major diameters of countersinks measure between 2.3mm and 12.7mm using one of the
following standard angles: 82°, 90°, 100°, and 120°. Tolerance for formed countersink major
diameter is

+/- 0.254mm.

Countersink Tolerances

Machined countersink major diameter +/- 0,254 mm

Machined countersink minor diameter 2/3 thickness

Formed countersink major diameter +/- 0,381 mm

Formed countersink minor diameter +/- 0,381 mm

Countersink Dimensions
The distance between countersink centres should be kept to 8 times the thickness of the
material 

The distance between the bend line and countersink centre should be kept to a minimum of
3 times the material thickness and 4 times the material thickness from an edge.
Hems: The Principle of Hemming
Hems are folds at the end of a part to create a rounded edge.

There are various methods for producing sheet metal flattening The hemming process is
usually done in two steps: acute-angled is bend hemming of the envelope. For the hemming
process a high compaction pressure is required. The process develops a large axial force.
This force affects the material longitudinally of the machine.
Hem Feature Guidelines
Open and closed hems can be formed as required. The tolerance of a hem is dependent
upon the hem’s radius, material thickness and features near the hem. It is recommended the
minimum inside diameter equals the material thickness and the hem return length is 4 times
the thickness. Closed hems are folds at the end of a part to create a rounded edge. The
tolerance of a hem is dependent upon the hem’s radius, material thickness, and features near
the hem. It is recommend that the minimum inside diameter equals the material thickness,
and the hem return length is 6 times material thickness.
Hemming is nothing but to fold the metal back on itself. In Sheet Metal hems are used to
create folds in sheet metal in order to stiffen edges and create an edge safe to touch. Hems
are most often used to remove a sharp untreated edge and make it safe for handling. Hems
are commonly used to hide imperfections and provide a generally safer edge to handle. A
combination of two hems can create strong, tight joints with little or minimal fastening.
Hems can even be used to strategically double the thickness of metal in areas of a part
which may require extra support. It is recommended that:

For tear drop hems, the inside diameter should be equal to the material thickness.

Open Hem Inner Radius


Tear-Drop Hem Inner Radius

For open hem the bend will lose its roundness when the inside diameter is greater than the
sheet metal thickness. 

For bends, the minimum distance between the inside edge of the bend and the outside of
the hem should be 5 times material thickness plus bend radius plus hem radius.

Holes & Slots: Dimensions


Keep hole and slot diameters at least as large as material thickness. Higher strength
materials require larger diameters. 

Clearances

Holes and slots may become deformed when placed near a bend. The minimum distance
they should be placed from a bend depends on the material thickness, the bend radius, and
their diameter. Be sure to place holes away from bends at a distance of at least 2.5 times the
material’s thickness plus the bend radius. Slots should be placed 4 times the material’s
thickness plus the bend radius away from the bend Be sure to place holes and slots at least
thickness plus the bend radius away from the bend. Be sure to place holes and slots at least
2 times the material’s thickness away from an edge to avoid a “bulging” effect. Holes should
be placed at least 6 times the material’s thickness apart.

Notches & Tabs Feature Notches


Notches must be at least the material’s thickness, whichever is greater, and can be no longer
than 5 times its width. Tabs must be at least twice times the material’s thickness or 3.2mm,
whichever is greater, and can be no longer than 5 times its width.

Bend notches

Notching is a shearing operation that removes a section from the outer edge of the metal
strip or part. In case, distance between the notches to bend is very small then distortion of
sheet metal may take place. To avoid such condition notch should be placed at appropriate
distance from bend with respect to sheet thickness. Notching is a low-cost process,
particularly for its low tooling costs with a small range of standard punches.
Clearances 

Notches must be at least 3.175mm away from each other. For bends, notches must be at
least 3 times the material’s thickness plus the bend radius. Tabs must have a minimum
distance from each other of 1mm or the material’s thickness, whichever is greater.

Recommendations for Notch Feature:

Notch width should not be narrower than 1.5 * t.

Length of notches can be up to 5 * t. Recommended corner radius for notches should be 0.5
* t.

Notches must be at least the material’s thickness or 0.04”, whichever is greater, and can be
no longer than 5 times its width. Tabs must be at least 2 times the material’s thickness or
0.126”, whichever is greater, and can be no longer than 5 times its width.

FEATURES
Corner Fillets
Filleting or rounding the corners of sheet metal is done in order to provide a smooth finish.
Fillets remove sharp

corners making them easier to handle and preventing cuts and scratches.

A fillet is usually designed to be ½ the material’s thickness and filleting makes parts more
cost-effective.
Relief Cuts

Relief cuts help parts fall closer to design intent to avoid “overhangs” and tearing at bends.
Overhangs become more prominent for thicker parts with a smaller bend radius, and may
even be as large as ½ the material’s thickness. Tearing may occur when bends are made close
to an edge.

Dimensions

Relief cuts for bends must be at least one material’s thickness in width, and must be longer
than the bend radius.

GET STARTED TODAY


Upload your parts to get started

Manufacturing the future.

T. 020 3962 9020


E. [email protected]

   
   

A BOU T
About Us
Our Platform
CA PA BIL ITIES
CNC Machining
Injection Moulding
Sheet Metal
3D Printing

MATERIA L S

CNC Machining Materials


Injection Moulding Materials
Sheet Metal Materials
3D Printing Materials

RESOU RCES

Manufacturing Resources
CNC Design Guide
Injection Moulding Design Guide
Sheet Metal Design Guide
3D Printing Design Guide

COMPA N Y

Blog
Careers
Our Partners
Privacy Policy
Terms & Conditions
Promotion Terms & Conditions
Referral Terms and Conditions

CON TA CT

Contact Us
Events
FAQ
Copyright © 2021 Geomiq. All rights reserved. Registration number. 10321594. VAT Nr.GB 258421205.

You might also like