Report

On

Produce Electricity from Nuclear Power Plant

Prepared By: Md. Raisul Karim Riad ID # 09207042 Program : BSME

Contents
1. Excutive Summary
2. Introduction
3. 4. 5. 6. 7. 8. 9.

Page-04 Page-06 Page-05 Page-07 Page-08 Page-10 Page-12 Page-13 Page-14 Page-16 Page-24 Page-25 Page-27 Page-28

Nuclear Fuel (Uranium) List of Nuclear power plant History Early Years Types of Reactors Uranium Processed Uranium Preparation of a Nuclear Reactor (PWR)

10. Parts 11. 12. 13. 14.

Life Cycle Conventional Fuel Resources Water Waste Radio Active

15. Comparing 16. 17.

Page-30 Page-31 Page-32

Reprocessing Depleted Uranium

3
18. 19. 20. 21. 22.

From Fission to Electricity Development Economics Future of the Industry Nuclear Power Plant In Bangladesh

Page-34 Page-35 Page-37 Page-38 Page-40

23. Bibliography

Page-46

The Nuclear Power Plant

Executive Summary:
A nuclear power plant harnesses the energy inside atoms themselves and converts this to electricity. A nuclear power plant uses controlled nuclear fission. Nuclear energy is energy in the nucleus (core) of an atom. Atoms are tiny particles that make up every object in the universe. There is enormous energy in the bonds that hold atoms together. Nuclear energy can be used to make electricity. But first the energy must be released. It can be released from atoms in two ways: nuclear fusion and nuclear fission. . Nuclear power plants use this energy to produce electricity. In nuclear fusion, energy is released when atoms are combined or fused together to form a larger atom. The fuel most widely used by nuclear plants for nuclear fission is uranium. Nuclear plants use a certain kind of uranium, referred to as U-235. This kind of uranium is used as fuel because its atoms are easily split apart. Just as there are different approaches to designing and building airplanes and automobiles, engineers have developed different types of nuclear power plants. Two types are used: boiling-water reactors and pressurized-water reactors. In a boiling-water reactor, the water heated by the reactor core turns directly into steam in the reactor vessel and is then used to power the turbine-generator. In a pressurized-water reactor, the water heated by the reactor core is kept under pressure so that it does not turn to steam at all it remains liquid. A typical nuclear reactor has a few main parts. Inside the "core" where the nuclear reactions take place are the fuel rods and assemblies, the control rods, the moderator, and the coolant. Outside the core are the turbines, the heat exchanger, and part of the cooling system. The fuel assemblies are collections of fuel rods. These rods are each about 3.5 meters (11.48 feet) long. They are each about a centimeter in diameter. These are grouped into large bundles of a couple hundred rods called fuel assemblies, which are then placed in the reactor core. Inside each fuel rod are hundreds of pellets of uranium fuel stacked end to end. Also in the core are control rods. These rods have pellets inside that are made of very efficient neutron capturers. An example of such a material is cadmium. These control rods are connected to machines that can raise or lower them in the core. When they are fully lowered into the core, fission cannot occur because they absorb free neutrons. However, when they are pulled out of the reactor, fission can start again anytime a stray neutron strikes a 235U atom, thus

6 releasing more neutrons, and starting a chain reaction. Another component of the reactor is the moderator. As opposed to current light water reactors which use uranium-235 (0.7% of all natural uranium), fast breeder reactors use uranium-238 (99.3% of all natural uranium). The most important waste stream from nuclear power plants is spent fuel. A large nuclear reactor produces 3 cubic meters (2530 tones) of spent fuel each year. It is primarily composed of unconverted uranium as well as significant quantities of transuranic actinides (plutonium and curium, mostly). In addition, about 3% of it is made of fission products. Spent fuel is highly radioactive and needs to be handled with great care and forethought. However, spent nuclear fuel becomes less radioactive over the course of thousands of years of time. After about 5 percent of the rod has reacted the rod is no longer able to be used. Today, scientists are experimenting on how to recycle these rods to reduce waste. In the meantime, after 40 years, the radiation flux is 99.9% lower than it was the moment the spent fuel was removed, although still dangerously radioactive. Spent fuel rods are stored in shielded basins of water (spent fuel pools), usually located on-site. The nuclear industry also produces a huge volume of low-level radioactive waste in the form of contaminated items like clothing, hand tools, water purifier resins, and (upon decommissioning) the materials of which the reactor itself is built. In the United States, the Nuclear Regulatory Commission has repeatedly attempted to allow low-level materials to be handled as normal waste: land filled, recycled into consumer items, et cetera. Most low-level waste releases very low levels of radioactivity and is only considered radioactive waste because of its history. Unlike fossil fuel-fired power plants, nuclear power plants produce no air pollution or carbon dioxide. India and Pakistan generate 2 per cent of their electricity from nuclear reactors, while South Korea gets 29 per cent of its electricity from nuclear plants, Japan 25, United States 20, Russia 17 and United Kingdom 14 per cent. Bangladesh wants to set up first nuclear power plant at Rooppur in Pabna and the land was acquired in 1963. Bangladesh would need at least 500 nuclear scientists for a 1,000 MW nuclear power plant for its operation and maintenance after its installation.

Introduction:
There are many different kinds of nuclear power plants, and we will discuss a few important designs in this text. A nuclear power plant harnesses the energy inside atoms themselves and converts this to electricity. This electricity is used by all of us. By now, we should have an idea of the fission process and how it works. A nuclear power plant uses controlled nuclear fission. In this section, we will explore how a nuclear power plant operates and the manner in which nuclear reactions are controlled. Just as many conventional thermal power stations generate electricity by harnessing the thermal energy released from burning fossil fuels, nuclear power plants convert the energy released from the nucleus of an atom, typically via nuclear fission.

Energy from Atoms:

Nuclear energy is energy in the nucleus (core) of an atom. Atoms are tiny particles that make up every object in the universe. There is enormous energy in the bonds that hold atoms together. Nuclear energy can be used to make electricity. But first the energy must be released. It can be released from atoms in two ways: nuclear fusion and nuclear fission.

Nuclear explosion In nuclear fission, atoms are split apart to form smaller atoms, releasing energy. Nuclear power plants use this energy to produce electricity. In nuclear fusion, energy is released

8 when atoms are combined or fused together to form a larger atom. This is how the sun produces energy. Fusion is the subject of ongoing research, but it is not yet clear that it will ever be a commercially viable technology for electricity generation.

Nuclear Fuel: (Uranium)

Uranium Ore The fuel most widely used by nuclear plants for nuclear fission is uranium. Uranium is nonrenewable, though it is a common metal found in rocks all over the world. Nuclear plants use a certain kind of uranium, referred to as U-235. This kind of uranium is used as fuel because its atoms are easily split apart. Though uranium is quite common, about 100 times more common than silver, U-235 is relatively rare. Most U.S. uranium is mined in the Western United States.

Nuclear Fission

9 Once uranium is mined, the U-235 must be extracted and processed before it can be used as a fuel. During nuclear fission, a small particle called a neutron hits the uranium atom and splits it, releasing a great amount of energy as heat and radiation. More neutrons are also released. These neutrons go on to bombard other uranium atoms, and the process repeats itself over and over again. This is called a chain reaction.

Chain Reaction

Nuclear power:
Nuclear power generally refers to electrical power from controlled (ie, non-explosive) nuclear reactions. Commercial plants in use to date use nuclear fission reactions. Electric utility reactors heat water to produce steam, which is then used to generate electricity. In 2007, 14% of the world's electricity came from nuclear power, despite concerns about safety and radioactive waste management. More than 150 naval vessels using nuclear propulsion have been built. Nuclear reactions are widely believed to be safer than fission and appear potentially viable, though technically quite difficult. Fusion power has been under intense theoretical and experimental investigation for many years. Both fission and fusion appear promising for some space propulsion applications in the mid- to distantfuture, using low thrust for long durations to achieve high mission velocities. Radioactive decay has been used on a relatively small (few kW) scale, mostly to power space missions and experiments.

10

Diagram: Basic function

List of nuclear reactors:

Chart: Electricity generation As of 2005, nuclear power provided 2.1% of the world's energy and 15% of the world's electricity, with the U.S., France, and Japan together accounting for 56.5% of nuclear generated electricity. In 2007, the IAEA reported there were 439 nuclear power reactors in operation in the world, operating in 31 countries. In 2007, nuclear power's share of global electricity generation dropped to 14%. According to the International Atomic Energy Agency, the main reason for this was an earthquake in western Japan on 16 July 2007, which shut down all seven reactors at the Kashiwazaki-Kariwa Nuclear Power Plant. There were also several other reductions and "unusual outages" experienced in Korea and Germany. Also, increases in the load factor for the current fleet of reactors appear to have platitude. The United States produces the most nuclear energy, with nuclear power providing 19% of the electricity it consumes, while France produces the highest percentage of its electrical energy from nuclear reactors78% as of 2006. In the European Union as a whole, nuclear energy provides 30% of the electricity. Nuclear

11 energy policy differs between European Union countries, and some, such as Austria, Estonia, and Ireland, have no active nuclear power stations. In comparison, France has a large number of these plants, with 16 multi-unit stations in current use. In the US, while the Coal and Gas Electricity industry is projected to be worth $85 billion by 2013, Nuclear Power generators are forecast to be worth $18 billion. Many military and some civilian (such as some icebreaker) ships use nuclear marine propulsion, a form of nuclear propulsion. A few space vehicles have been launched using full-fledged nuclear reactors: the Soviet RORSAT series and the American SNAP-10A. International research is continuing into safety improvements such as passively safe plants, the use of nuclear fusion, and additional uses of process heat such as hydrogen production (in support of a hydrogen economy), for desalinating sea water, and for use in district heating systems.

History:
As the father of nuclear physics, Ernest Rutherford is credited with splitting the atom in 1917. His team in England bombarded nitrogen with naturally occurring alpha particles from radioactive material and observed a proton emitted with energy higher than the alpha particle. In 1932 two of his students John Cockcroft and Ernest Walton, working under Rutherford's direction, attempted to split the atomic nucleus by entirely artificial means, using a particle accelerator to bombard lithium with protons, thereby producing two helium nuclei. After James Chadwick discovered the neutron in 1932, nuclear fission was first experimentally achieved by Enrico Fermi in 1934 in Rome, when his team bombarded uranium with neutrons.

Uranium Ore

12 In 1938, German chemists Otto Hahn and Fritz Strassmann, along with Austrian physicists Lise Meitner and Meitner's nephew, Otto Robert Frisch, conducted experiments with the products of neutron-bombarded uranium. They determined that the relatively tiny neutron split the nucleus of the massive uranium atoms into two roughly equal pieces, which was a surprising result. Numerous scientists, including Leo Szilard who was one of the first, recognized that if fission reactions released additional neutrons, a self-sustaining nuclear chain reaction could result. This spurred scientists in many countries (including the United States, the United Kingdom, France, Germany, and the Soviet Union) to petition their government for support of nuclear fission research. In the United States, where Fermi and Szilard had both emigrated, this led to the creation of the first man-made reactor, known as Chicago Pile-1, which achieved criticality on December 2, 1942. This work became part of the Manhattan Project, which built large reactors at the Hanford Site (formerly the town of Hanford, Washington) to breed plutonium for use in the first nuclear weapons, which were used on the cities of Hiroshima and Nagasaki. A parallel uranium enrichment effort also was pursued. After World War II, the fear that reactor research would encourage the rapid spread of nuclear weapons and technology, combined with what many scientists thought would be a long road of development, created a situation in which the government attempted to keep reactor research under strict government control and classification. In addition, most reactor research centered on purely military purposes. Actually, there were no secrets to the technology. There was an immediate arms and development race when the United States military refused to follow the advice of its own scientific community to form an international cooperative to share information and control nuclear materials. By 2006, things have come full circle with the Global Nuclear Energy Partnership (see below.) Electricity was generated for the first time by a nuclear reactor on December 20, 1951 at the EBR-I experimental station near Arco, Idaho, which initially produced about 100 kW (the Arco Reactor was also the first to experience partial meltdown, in 1955). In 1952, a report by the Paley Commission (The President's Materials Policy Commission) for President Harry Truman made a "relatively pessimistic" assessment of nuclear power, and called for "aggressive research in the whole field of solar energy."[17] A December 1953 speech by President Dwight Eisenhower, "Atoms for Peace," emphasized the useful

13 harnessing of the atom and set the U.S. on a course of strong government support for international use of nuclear power.

Early years:

Diagram: Nuclear processing plant. Calder Hall nuclear power station in the United Kingdom was the world's first nuclear power station to produce electricity in commercial quantities.

Diagram: Nuclear power plant The Shipping port Atomic Power Station in Shipping port, Pennsylvania was the first commercial reactor in the USA and was opened in 1957. On June 27, 1954, the USSR's Obninsk Nuclear Power Plant became the world's first nuclear power plant to generate electricity for a power grid, and produced around 5 megawatts of electric power. Later in 1954, Lewis Strauss, then chairman of the United States Atomic Energy Commission (U.S. AEC, forerunner of the U.S. Nuclear Regulatory Commission and the United States Department of Energy) spoke of electricity in the future being "too cheap to meter." The

14 U.S. AEC itself had issued far more conservative testimony regarding nuclear fission to the U.S. Congress only months before, projecting that "costs can be brought down ... about the same as the cost of electricity from conventional sources..." Strauss may have been making vague reference to hydrogen fusion - which was secret at the time - rather than uranium fission, but whatever his intent Strauss's statement was interpreted by much of the public as a promise of very cheap energy from nuclear fission. Significant disappointment would develop later on, when the new nuclear plants did not provide energy "too cheap to meter." In 1955 the United Nations' "First Geneva Conference", then the world's largest gathering of scientists and engineers, met to explore the technology. In 1957 EURATOM was launched alongside the European Economic Community (the latter is now the European Union). The same year also saw the launch of the International Atomic Energy Agency (IAEA). The world's first commercial nuclear power station, Calder Hall in Sellafield, England was opened in 1956 with an initial capacity of 50 MW (later 200 MW). The first commercial nuclear generator to become operational in the United States was the Shipping port Reactor (Pennsylvania, December, 1957). One of the first organizations to develop nuclear power was the U.S. Navy, for the purpose of propelling submarines and aircraft carriers. It has a good record in nuclear safety, perhaps because of the stringent demands of Admiral Hyman G. Rickover, who was the driving force behind nuclear marine propulsion as well as the Shipping port Reactor. The U.S. Navy has operated more nuclear reactors than any other entity, including the Soviet Navy, with no publicly known major incidents. The first nuclearpowered submarine, USS Nautilus (SSN-571), was put to sea in December 1954. Two U.S. nuclear submarines, USS Scorpion and USS Thresher, have been lost at sea. These vessels were both lost due to malfunctions in systems not related to the reactor plants. Also, the sites are monitored and no known leakage has occurred from the onboard reactors. The United States Army also had a nuclear power program, beginning in 1954. The SM-1 Nuclear Power Plant, at Ft. Belvoir, Va., was the first power reactor in the US to supply electrical energy to a commercial grid (VEPCO), in April 1957, before shipping port. Enrico Fermi and Le Szilrd in 1955 shared U.S. Patent 2,708,656 for the nuclear reactor, belatedly granted for the work they had done during the Manhattan Project.

15

Types of Reactor:

Types of Reactor Just as there are different approaches to designing and building airplanes and automobiles, engineers have developed different types of nuclear power plants. Two types are used: boiling-water reactors and pressurized-water reactors.

16

Boiling-Water Reactors:
In a boiling-water reactor, the water heated by the reactor core turns directly into steam in the reactor vessel and is then used to power the turbine-generator.

Diagram: Basic function

Pressurized-Water Reactors:
In a pressurized-water reactor, the water heated by the reactor core is kept under pressure so that it does not turn to steam at all it remains liquid. This hot radioactive water flows through a piece of equipment called a steam generator. A steam generator is a giant cylinder with thousands of tubes in it that the hot radioactive water can flow through and heat up. Outside these hot tubes in the steam generator is no radioactive water (or clean water), which eventually boils and turns to steam. The radioactive water flows back to the reactor core, where it is reheated and then sent back to the steam generator. The clean water may come from one of several sources including oceans, lakes, or rivers.

Uranium Processed:
Uranium is nonrenewable, though it is a common metal found in rocks all over the world. Uranium occurs in nature in combination with small amounts of other elements. Nuclear

17 plants use a certain kind of uranium, U-235, as fuel because its atoms are easily split apart. Though uranium is quite common, about 100 times more common than silver, U235 is relatively rare. Economically recoverable uranium deposits have been discovered principally in the western United States, Australia, Canada, Africa, and South America. Once uranium is mined, the U-235 must be extracted and processed before it can be used as a fuel. Mined uranium ore typically yields one to four pounds of uranium concentrate (U3O8 or "yellowcake") per ton, or 0.05% to 0.20% U3O8.

Core

Uranium Preparation:
Uranium 235U will not be the only isotope of uranium present in a nuclear reactor. In naturally occurring uranium deposits, less than one percent of the uranium is 235U. The majority of the uranium is 238U. 238U is not a fissile isotope of uranium. When 238U is struck by a loose neutron, it absorbs the neutron into its nucleus and does not fission. Thus, by absorbing loose neutrons, 238U can prevent a nuclear chain reaction from occurring. This would be a bad thing because if a chain reaction doesn't occur, the nuclear reactions can't sustain themselves, the reactor shuts down, and millions of people are without electrical power. In order for a chain reaction to occur, the pure uranium ore must be refined to raise the concentration of 235U. This is called enrichment and is primarily accomplished through a technique called gaseous diffusion. In this process, the uranium ore is combined with fluorine to create a chemical compound called uranium

18 hexafluoride. The uranium hexafluoride is heated and vaporizes. The heated gas is then pushed through a series of filters. Because some of the uranium hexafluoride contains 238U and some contains 235U, there is a slight difference in the weights of the individual molecules. The molecules of uranium hexafluoride containing 235U are slightly lighter and thus pass more easily through the filters. This creates a quantity of uranium hexafluoride with a higher proportion of 235U. This is collected, the uranium is stripped from it, and the result is an enriched supply of fuel. Usually, nuclear power plants use uranium fuel that is about 4% 235U.

Diagram: Two major part of nuclear power plant

Diagram: Inside of Nuclear Reactor

19

Parts of a Nuclear Reactor (PWR):

A typical nuclear reactor has a few main parts. Inside the "core" where the nuclear reactions take place are the fuel rods and assemblies, the control rods, the moderator, and the coolant. Outside the core are the turbines, the heat exchanger, and part of the cooling system. The fuel assemblies are collections of fuel rods. These rods are each about 3.5 meters (11.48 feet) long. They are each about a centimeter in diameter. These are grouped into large bundles of a couple hundred rods called fuel assemblies, which are then placed in the reactor core. Inside each fuel rod are hundreds of pellets of uranium fuel stacked end to end. Also in the core are control rods. These rods have pellets inside that are made of very efficient neutron capturers. An example of such a material is cadmium. These control rods are connected to machines that can raise or lower them in the core. When they are fully lowered into the core, fission can not occur because they absorb free neutrons. However, when they are pulled out of the reactor, fission can start again anytime a stray neutron strikes a 235U atom, thus releasing more neutrons, and starting a chain reaction. Another component of the reactor is the moderator. The moderator serves to slow down the high speed neutrons "flying" all around the reactor core. If a neutron is moving too fast, and thus is at a highenergy state, it passes right through the 235U nucleus. It must be slowed down to be captured by the nucleus and to induce fission. The most common moderator is water, but sometimes it can be another material. The job of the coolant is to absorb the heat from the reaction. The most common coolant used in nuclear power plants today is water. In actuality, in many reactor designs the coolant and the moderator are one and the same. The coolant water is heated by the nuclear reactions going on inside the core. However, Fuel Fuel Assembly Rods

Containing a Number of

20 this heated water does not boil because it is kept at an extremely intense pressure, thus raising its boiling point above the normal 100 Celsius.

The Inside of a Reactor Containment Structure One can see the heavy concrete walls from which the structure is made. Also, a fuel rod transportation canister is in the background (blue arrow). In front of that is the pit where the reactor core would normally reside (red arrow).

21 The heated water rises up and passes through another part of the reactor, the heat exchanger. The moderator/coolant water is radioactive, so it can not leave the inner reactor containment. Its heat must be transferred to non-radioactive water, which can then be sent out of the reactor shielding. This is done through the heat exchanger, which works by moving the radioactive water through a series of pipes that are wrapped around other pipes. The metallic pipes conduct the heat from the moderator to the normal water. Then, the normal water (now in steam form and intensely hot) moves to the turbine, where electricity is produced. Three Mile Island, the Site of a Nuclear Accident The steam towers are the large objects in the upper part of the picture. They do not actually house any reactors, and their only purpose is to cool water after it has passed through the turbines.

After the hot water has passed through the turbine, some of its energy is changed into electricity. However, the water is still very hot. It must be cooled somehow. Many nuclear power plants used steam towers to cool this water with air. These are generally the buildings that people associate with nuclear power plants. At reactors that do not have

22 towers, the clean water is purified and dumped into the nearest body of water, and cool water is pumped in to replace it.

Basic Function

Reactor Cold coolant:

After releasing its heat to the steam generator, the cold coolant returns to the reactor.

23

Transfer of heat to water:

The coolant releases the heat given off by the fission of uranium to the steam generator.

Water Pipes

Hot coolant:
The coolant extracts heat from the fuel and carries it toward the steam generator.

Water turns into steam:

The hot coolant heats the water of the generator and brings it to the boiling point.

Reactor:
Tightly sealed area where fission of the fuel is carried out in a controlled manner to release heat.

Process

24

Containment building:
Concrete building used to collect the radioactive steam from the reactor in the event of an accident.

Cooling Tower

Dousing water tank:

Vat that contains water to cool the radioactive steam in the reactor in the event of an accident; this prevents a rise in pressure.

Sprinklers:
Devices that are release water to condense radioactive steam.

Safety valve:
Devices that are lower the pressure inside the reactor by discharging the radioactive steam to the containment building.

Valve

25

Fission of uranium fuel:

The nuclei of the atoms break up; this frees neutrons and releases energy in the form of heat.

Production of electricity by the generator:

The generator produces electricity through the movement of the rotor in the stator.

Heat production:
The fission of atoms releases intense heat (between 575F and 925F), which is transmitted to the coolant.

Heat Transfer

Turbine shaft turns generator:

The rotational movement of the turbine is transmitted to the generators rotor.

Generator

26

Coolant:
Liquid or gas (including heavy water and carbon dioxide) that circulates inside the reactor; it harnesses and transports the heat released during fission of the fuel.

Water into steam generator:

After passing through the turbine, water produced by the condensation of the steam returns to the steam generator.

Water cools the used steam:

Cooling of the steam from the turbine is done with river or lake water.

Condensation of steam into water:

At the turbine outlet, the steam cools and condenses into water.

Electricity transmission:
Using high-voltage lines to transmit electricity over long distances reduces the strength of the current and, as a result, energy losses.

27

Voltage increase:
At the outlet end of the power plant, the transformer increases the voltage; this reduces energy losses during transmission over long distances.

Meter

Steam pressure drives turbine:

Steam from the steam generator turns the turbine runner, which is connected to the generator.

Turbine

Fuel:
Matter placed in the core of the reactor that contains heavy atoms (uranium, plutonium); energy is extracted from it by fission.

Moderator:
Substance (ordinary water, heavy water, graphite) that slows the fast-moving neutrons emitted during fission to increase the probability of new collisions.

Life cycle:

28

Life Cycle The Nuclear Fuel Cycle begins when uranium is mined, enriched, and manufactured into nuclear fuel, (1) which is delivered to a nuclear power plant. After usage in the power plant, the spent fuel is delivered to a reprocessing plant (2) or to a final repository (3) for geological disposition. In reprocessing 95% of spent fuel can be recycled to be returned to usage in a power plant (4). A nuclear reactor is only part of the life-cycle for nuclear power. The process starts with mining. Uranium mines are underground, open-pit, or insitu leach mines. In any case, the uranium ore is extracted, usually converted into a stable and compact form such as yellowcake, and then transported to a processing facility. Here, the yellowcake is converted to uranium hexafluoride, which is then enriched using various techniques. At this point, the enriched uranium, containing more than the natural 0.7% U-235, is used to make rods of the proper composition and geometry for the particular reactor that the fuel is destined for. The fuel rods will spend about 3 operational cycles (typically 6 years total now) inside the reactor, generally until about 3% of their uranium has been fissional, then they will be moved to a spent fuel pool where the short lived isotopes generated by fission can decay away. After about 5 years in a cooling pond, the spent fuel is radioactively and thermally cool enough to handle, and it can be moved to dry storage casks or reprocessed.

Conventional fuel resources:

29

Fuel Uranium is a fairly common element in the Earth's crust. Uranium is approximately as common as tin or germanium in Earth's crust, and is about 35 times more common than silver. Uranium is a constituent of most rocks, dirt, and of the oceans. The fact that uranium is so spread out is a problem because mining uranium is only economically feasible where there is a large concentration. Still, the world's present measured resources of uranium, economically recoverable at a price of 130 USD/kg, are enough to last for "at least a century" at current consumption rates. This represents a higher level of assured resources than is normal for most minerals. On the basis of analogies with other metallic minerals, a doubling of price from present levels could be expected to create about a tenfold increase in measured resources, over time. However, the cost of nuclear power lies for the most part in the construction of the power station. Therefore the fuel's contribution to the overall cost of the electricity produced is relatively small, so even a large fuel price escalation will have relatively little effect on final price. For instance, typically a doubling of the uranium market price would increase the fuel cost for a light water reactor by 26% and the electricity cost about 7%, whereas doubling the price of natural gas would typically add 70% to the price of electricity from that source. At high enough prices, eventually extraction from sources such as granite and seawater become economically feasible. Current light water reactors make relatively inefficient use of nuclear fuel, fissioning only the very rare uranium-235 isotope. Nuclear reprocessing can make this waste reusable and more efficient reactor designs allow better use of the available resources.

30

Breeding:
As opposed to current light water reactors which use uranium-235 (0.7% of all natural uranium), fast breeder reactors use uranium-238 (99.3% of all natural uranium). It has been estimated that there is up to five billion years worth of uranium-238 for use in these power plants. Breeder technology has been used in several reactors, but the high cost of reprocessing fuel safely requires uranium prices of more than 200 USD/kg before becoming justified economically. As of December 2005, the only breeder reactor producing power is BN-600 in Beloyarsk, Russia. The electricity output of BN-600 is 600 MW Russia has planned to build another unit, BN-800, at Beloyarsk nuclear power plant. Also, Japan's Monju reactor is planned for restart (having been shut down since 1995), and both China and India intend to build breeder reactors. Another alternative would be to use uranium-233 bred from thorium as fission fuel in the thorium fuel cycle. Thorium is about 3.5 times as common as uranium in the Earth's crust, and has different geographic characteristics. This would extend the total practical fissionable resource base by 450%.Unlike the breeding of U-238 into plutonium, fast breeder reactors are not necessary it can be performed satisfactorily in more conventional plants. India has looked into this technology, as it has abundant thorium reserves but little uranium.

Water:

Water Pipes

31 Like all forms of power generation using steam turbines, nuclear power plants use large amounts of water for cooling. At Sellafield, which is no longer producing electricity, a maximum of 18,184.4 m a day (over 4 million gallons) and 6,637,306 m a year (figures from the Environment Agency) of fresh water from Waste Water is still abstracted to use on site for various processes. As with most power plants, two-thirds of the energy produced by a nuclear power plant goes into waste heat (see Carnot cycle), and that heat is carried away from the plant in the water (which remains uncontaminated by radioactivity). The emitted water either is sent into cooling towers where it goes up and is emitted as water droplets (literally a cloud) or is discharged into large bodies of water cooling ponds, lakes, rivers, or oceans. Droughts can pose a severe problem by causing the source of cooling water to run out. The Palo Verde Nuclear Generating Station near Phoenix, AZ is the only nuclear generating facility in the world that is not located adjacent to a large body of water. Instead, it uses treated sewage from several nearby municipalities to meet its cooling water needs, recycling 20 billion US gallons (76,000,000 m) of wastewater each year. Like conventional power plants, nuclear power plants generate large quantities of waste heat which is expelled in the condenser, following the turbine. Coloration of plants that can take advantage of this thermal energy has been suggested by Oak Ridge National Laboratory (ORNL) as a way to take advantage of process synergy for added energy efficiency. One example would be to use the power plant steam to produce hydrogen from water. (Separation of water into hydrogen and oxygen can use less energy if the water begins at a high temperature.)

Solid waste:
The safe storage and disposal of nuclear waste is a significant challenge and yet unresolved problem. The most important waste stream from nuclear power plants is spent fuel. A large nuclear reactor produces 3 cubic meters (2530 tones) of spent fuel each year. It is primarily composed of unconverted uranium as well as significant quantities of transuranic actinides (plutonium and curium, mostly). In addition, about 3% of it is made of fission products. The actinides (uranium, plutonium, and curium) are responsible for

32 the bulk of the long term radioactivity, whereas the fission products are responsible for the bulk of the short term radioactivity.

High-level radioactive waste:

Core Spent fuel is highly radioactive and needs to be handled with great care and forethought. However, spent nuclear fuel becomes less radioactive over the course of thousands of years of time. After about 5 percent of the rod has reacted the rod is no longer able to be used. Today, scientists are experimenting on how to recycle these rods to reduce waste. In the meantime, after 40 years, the radiation flux is 99.9% lower than it was the moment the spent fuel was removed, although still dangerously radioactive. Spent fuel rods are stored in shielded basins of water (spent fuel pools), usually located on-site. The water provides both cooling for the still-decaying fission products, and shielding from the continuing radioactivity. After a few decades some on-site storage involves moving the now cooler, less radioactive fuel to a dry-storage facility or dry cask storage, where the fuel is stored in steel and concrete containers until its radioactivity decreases naturally ("decays") to levels safe enough for other processing. This interim stage spans years or decades or millennia, depending on the type of fuel. Most U.S. waste is currently stored in temporary storage sites requiring oversight, while suitable permanent disposal methods are discussed. As of 2007, the United States had accumulated more than 50,000 metric tons of spent nuclear fuel from nuclear reactors. Underground storage at Yucca Mountain nuclear waste repository in U.S. has been proposed as permanent storage. After 10,000

33 years of radioactive decay, according to United States Environmental Protection Agency standards, the spent nuclear fuel will no longer pose a threat to public health and safety. The amount of waste can be reduced in several ways, particularly reprocessing. Even so, the remaining waste will be substantially radioactive for at least 300 years even if the actinides are removed and for up to thousands of years if the actinides are left in. Even with separation of all actinides, and using fast breeder reactors to destroy by transmutation some of the longer-lived non-actinides as well, the waste must be segregated from the environment for one to a few hundred years, and therefore this is properly categorized as a long-term problem. Sub critical reactors or fusion reactors could also reduce the time the waste has to be stored. It has been argued that the best solution for the nuclear waste is above ground temporary storage since technology is rapidly changing. There is hope that current waste may well become a valuable resource in the future. According to a 2007 story broadcast on 60 Minutes, nuclear power gives France the cleanest air of any industrialized country, and the cheapest electricity in all of Europe. France reprocesses its nuclear waste to reduce its mass and make more energy. However, the article continues, "Today we stock containers of waste because currently scientists don't know how to reduce or eliminate the toxicity, but maybe in 100 years perhaps scientists will... Nuclear waste is an enormously difficult political problem which to date no country has solved. It is, in a sense, the Achilles heel of the nuclear industry... If France is unable to solve this issue, says Mandil, then 'I do not see how we can continue our nuclear program.'" Further, reprocessing itself has its critics, such as the Union of Concerned Scientists.

Low-level radioactive waste:

The nuclear industry also produces a huge volume of low-level radioactive waste in the form of contaminated items like clothing, hand tools, water purifier resins, and (upon decommissioning) the materials of which the reactor itself is built. In the United States, the Nuclear Regulatory Commission has repeatedly attempted to allow low-level materials to be handled as normal waste: land filled, recycled into consumer items, et

34 cetera. Most low-level waste releases very low levels of radioactivity and is only considered radioactive waste because of its history.

Comparing radioactive to industrial toxic waste:

In countries with nuclear power, radioactive wastes comprise less than 1% of total industrial toxic wastes, which remain hazardous indefinitely unless they decompose or are treated so that they are less toxic or, ideally, completely non-toxic. Overall, nuclear power produces far less waste material than fossil-fuel based power plants. Coal-burning plants are particularly noted for producing large amounts of toxic and mildly radioactive ash due to concentrating naturally occurring metals and radioactive material from the coal. Recent reports claim that coal power actually results in more radioactive waste being released into the environment than nuclear power, and that the population effective dose equivalent from radiation from coal plants is 100 times as much as nuclear plants. However, reputable journals point out that coal ash is not more radioactive than nuclear waste, and the differences in exposure lie in the fact that nuclear plants use heavy shielding to protect the environment from the heavily irradiated reactor vessel, fuel rods, and any radioactive waste on site.

Reprocessing:
Reprocessing can potentially recover up to 95% of the remaining uranium and plutonium in spent nuclear fuel, putting it into new mixed oxide fuel. This produces a reduction in long term radioactivity within the remaining waste, since this is largely short-lived fission products, and reduces its volume by over 90%. Reprocessing of civilian fuel from power reactors is currently done on large scale in Britain, France and (formerly) Russia, soon will be done in China and perhaps India, and is being done on an expanding scale in Japan. The full potential of reprocessing has not been achieved because it requires breeder reactors, which are not yet commercially available. France is generally cited as the most successful preprocessor, but it presently only recycles 28% (by mass) of the yearly fuel use 7% within France and another 21% in Russia. Unlike other countries, the

35 US stopped civilian reprocessing from 1976 to 1981 as one part of US non-proliferation policy, since reprocessed material such as plutonium could be used in nuclear weapons: however, reprocessing is now allowed in the U.S. Even so, in the U.S. spent nuclear fuel is currently all treated as waste. In February, 2006, a new U.S. initiative, the Global Nuclear Energy Partnership was announced. It would be an international effort to reprocess fuel in a manner making nuclear proliferation unfeasible, while making nuclear power available to developing countries.

Reprocessing

Depleted Uranium:
Uranium enrichment produces many tons of depleted uranium (DU) which consists of U238 with most of the easily fissile U-235 isotope removed. U-238 is a tough metal with several commercial usesfor example, aircraft production, radiation shielding, and armoras it has a higher density than lead. Depleted uranium is also useful in munitions as DU penetrates (bullets or APFSDS tips) "self sharpen", due to uranium's tendency to fracture along shear bands. There are concerns that U-238 may lead to health problems in groups exposed to this material excessively, such as tank crews and civilians living in areas where large quantities of DU ammunition have been used in shielding, bombs, missile warheads, and bullets. In January 2003 the World Health Organization released a report finding that contamination from DU munitions were localized to a few tens of meters from the impact sites and contamination of local vegetation and water was 'extremely low'. The report also states that approximately 70% of ingested DU will leave the body after twenty four hours and 90% after a few days.

36

Debate on nuclear power:

Proponents of nuclear energy contend that nuclear power is a sustainable energy source that reduces carbon emissions and increases energy security by decreasing dependence on foreign oil. Proponents also emphasize that the risks of storing waste are small and can be further reduced by using the latest technology in newer reactors and that the operational safety record of nuclear plants in the Western world is far better when compared to the other major types of power plants. Critics believe that nuclear power is a potentially dangerous energy source, with decreasing proportion of nuclear energy in production, and dispute whether the risks can be reduced through new technology. Proponents advance the notion that nuclear power produces virtually no air pollution, in contrast to the chief viable alternative of fossil fuel combustion, and that nuclear waste storage technology virtually eliminates the risk of radiation leakage. Proponents also point out that nuclear power is the only viable course to achieve energy independence for most Western countries. Critics point to the issue of storing radioactive waste, the history of and continuing potential for radioactive contamination by accident or sabotage, the continuing possibility of nuclear proliferation, and the disadvantages of centralized electricity production. Arguments of economics and safety are used by both sides of the debate.

Spent Fuel:
The spent fuel assemblies, on the other hand, are highly radioactive and must initially be stored in specially designed pools resembling large swimming pools (water cools the fuel and acts as a radiation shield) or in specially designed dry storage containers. An

37 increasing number of reactor operators now store their older spent fuel in dry storage facilities using special outdoor concrete or steel containers with air cooling.

Carbon Dioxide:
Unlike fossil fuel-fired power plants, nuclear power plants produce no air pollution or carbon dioxide. However, a small amount of emissions result from processing the uranium that is used in nuclear reactors.

From Fission to Electricity:

A nuclear power plant produces electricity in almost exactly the same way that a conventional (fossil fuel) power plant does. A conventional power plant burns fuel to create heat. The fuel is generally coal, but oil is also sometimes used. The heat is used to raise the temperature of water, thus causing it to boil. The high temperature and intense pressure steam that result from the boiling of the water turns a turbine, which then generates electricity. A nuclear power plant works the same way, except that the heat used to boil the water is produced by a nuclear fission reaction using 235U as fuel, not the combustion of fossil fuels. A nuclear power plant uses much less fuel than a

38 comparable fossil fuel plant. A rough estimate is that it takes 17,000 kilograms of coal to produce the same amount of electricity as 1 kilogram of nuclear uranium fuel.

Other Types of Reactors:

Although the most common type of reactor is the Pressurized Water Reactor (PWR), many other types of reactors are also used. In the PWR, as we described earlier, there are two main water cycles. One is the water inside the core that is highly radioactive. This water's heat is transferred to other, non-radioactive water inside the second loop. This water is then used to turn a turbine. The second most popular reactor type is the Boiling Water Reactor (BRW). This type of reactor differs from the PWR in that there is only one water cycle. Radioactive water is used to turn the turbine. The major disadvantage of this is that the radioactive nuclides in the water that cause its radioactivity can be transferred to the turbine, thus causing it to become radioactive too. This produces more hazardous material that needs to be disposed of when a reactor is dismantled. However, the BWR also has a few advantages. Its core can be kept at a lower pressure, for example. Another type of reactor is the Heavy Water Reactor (HWR). A HWR uses heavy water as a moderator instead of normal water. Heavy water is water with deuterium, which is an isotope of hydrogen with 1 neutron. Deuterium is heavier than normal hydrogen, which has no neutrons. HWR's come in two types, pressurized and boiling, just like normal "light water" reactors. The advantage of a HWR is that un-enriched uranium fuel can be used. This is because the heavy water is a much more efficient moderator than light

39 water. Thus, more stray neutrons can be slowed down enough to cause fission in 235U. This more efficient moderator makes up for the greater abundance of the neutroncapturing 238U.

Development:

History of the use of nuclear power and the number of active nuclear power plants Installed nuclear capacity initially rose relatively quickly, rising from less than 1 gigawatt (GW) in 1960 to 100 GW in the late 1970s, and 300 GW in the late 1980s. Since the late 1980s worldwide capacity has risen much more slowly, reaching 366 GW in 2005. Between around 1970 and 1990, more than 50 GW of capacity was under construction (peaking at over 150 GW in the late 70s and early 80s) in 2005, around 25 GW of new capacity was planned. More than two-thirds of all nuclear plants ordered after January 1970 were eventually cancelled. A total of 63 nuclear units were canceled in the USA between 1975 and 1980.

Inside of Power Plant

40

Inside of Power Plant Washington Public Power Supply System Nuclear Power Plants 3 and 5 were never completed. During the 1970s and 1980s rising economic costs (related to extended construction times largely due to regulatory changes and pressure-group litigation) and falling fossil fuel prices made nuclear power plants then under construction less attractive. In the 1980s (U.S.) and 1990s (Europe), flat load growth and electricity liberalization also made the addition of large new base load capacity unattractive. The 1973 oil crisis had a significant effect on countries, such as France and Japan, which had relied more heavily on oil for electric generation (39% and 73% respectively) to invest in nuclear power. Today, nuclear power supplies about 80% and 30% of the electricity in those countries, respectively. A general movement against nuclear power arose during the last third of the 20th century, based on the fear of a possible nuclear accident as well as the history of accidents, fears of radiation as well as the history of radiation of the public, nuclear proliferation, and on the opposition to nuclear waste production, transport and lack of any final storage plans. Perceived risks on the citizens' health and safety, the 1979 accident at Three Mile Island and the 1986 Chernobyl disaster played a part in stopping new plant construction in many countries, although the public policy organization Brookings Institution suggests that new nuclear units have not been ordered in the U.S. because the Institution's research concludes they cost 1530% more over their lifetime than conventional coal and natural gas fired plants. Unlike the Three Mile Island accident, the much more serious Chernobyl accident did not increase regulations affecting Western reactors since the Chernobyl reactors were of the problematic RBMK design only used in the Soviet Union, for example lacking "robust" containment buildings. Many of these reactors are still in use today. However, changes were made in both the reactors themselves (use of low enriched uranium) and in the control system

41 (prevention of disabling safety systems) to reduce the possibility of a duplicate accident. An international organization to promote safety awareness and professional development on operators in nuclear facilities was created: WANO; World Association of Nuclear Operators. Opposition in Ireland, and Poland prevented nuclear programs there, while Austria (1978), Sweden (1980) and Italy (1987) (influenced by Chernobyl) voted in referendums to oppose or phase out nuclear power. In July 2009, the Italian Parliament passed a law that canceled the results of an earlier referendum and allowed the immediate start of the Italian nuclear program.

Economics:
The economics of nuclear power plants are primarily influenced by the high initial investment necessary to construct a plant. In 2009, estimates for the cost of a new plant in the U.S. ranged from $6 to $10 billion. It is therefore usually more economical to run them as long as possible, or construct additional reactor blocks in existing facilities. In 2008, new nuclear power plant construction costs were rising faster than the costs of other types of power plants.. A prestigious panel assembled for a 2003 MIT study of the industry found the following: In deregulated markets, nuclear power is not now cost competitive with coal and natural gas. However, plausible reductions by industry in capital cost, operation and maintenance costs, and construction time could reduce the gap. Carbon emission credits, if enacted by government, can give nuclear power a cost advantage.

Future of the industry:

42

Head of Reactor As of 2007, Watts Bar 1, which came on-line in February 7, 1996, was the last U.S. commercial nuclear reactor to go on-line. This is often quoted as evidence of a successful worldwide campaign for nuclear power phase-out. However, even in the U.S. and throughout Europe, investment in research and in the nuclear fuel cycle has continued, and some nuclear industry experts predict electricity shortages, fossil fuel price increases, global warming and heavy metal emissions from fossil fuel use, new technology such as passively safe plants, and national energy security will renew the demand for nuclear power plants. According to the World Nuclear Association, globally during the 1980s one new nuclear reactor started up every 17 days on average, and by the year 2015 this rate could increase to one every 5 days. Many countries remain active in developing nuclear power, including Pakistan, Japan, China and India, all actively developing both fast and thermal technology, South Korea and the United States, developing thermal technology only, and South Africa and China, developing versions of the Pebble Bed Modular Reactor (PBMR). Several EU member states actively pursue nuclear programs, while some other member states continue to have a ban for the nuclear energy use. Japan has an active nuclear construction program with new units brought on-line in 2005. In the U.S., three consortia responded in 2004 to the U.S. Department of Energy's solicitation under the Nuclear Power 2010 Program and were awarded matching fundsthe Energy Policy Act of 2005 authorized loan guarantees for up to six new reactors, and authorized the Department of Energy to build a reactor based on the Generation IV Very-HighTemperature Reactor concept to produce both electricity and hydrogen. As of the early 21st century, nuclear power is of particular interest to both China and India to serve their

43 rapidly growing economiesboth are developing fast breeder reactors. (See also energy development). In the energy policy of the United Kingdom it is recognized that there is a likely future energy supply shortfall, which may have to be filled by either new nuclear plant construction or maintaining existing plants beyond their programmed lifetime. There is a possible impediment to production of nuclear power plants as only a few companies worldwide have the capacity to forge single-piece containment vessels, which reduce the risk of a radiation leak. Utilities across the world are submitting orders years in advance of any actual need for these vessels. Other manufacturers are examining various options, including making the component themselves, or finding ways to make a similar item using alternate methods. Other solutions include using designs that do not require single-piece forged pressure vessels such as Canada's Advanced CANDU Reactors or Sodium-cooled Fast Reactors.

Inside of Head This graph illustrates the potential rise in CO2 emissions if base-load electricity currently produced in the U.S. by nuclear power were replaced by coal or natural gas as current reactors go offline after their 60 year licenses expire. Note: graph assumes all 104 American nuclear power plants receive license extensions out to 60 years. The World Nuclear Industry Status Report 2009 states that "even if Finland and France each builds a reactor or two, China goes for an additional 20 plants and Japan, Korea or Eastern Europe add a few units, the overall worldwide trend will most likely be downwards over the next two decades". With long lead times of 10 years or more, it will be difficult to maintain or increase the number of operating nuclear power plants over the next 20 years. The one

44 exception to this outcome would be if operating lifetimes could be substantially increased beyond 40 years on average. This seems unlikely since the present average age of the operating nuclear power plant fleet in the world is 25 years. However, China plans to build more than 100 plants, while in the US the licenses of almost half its reactors have already been extended to 60 years, and plans to build more than 30 new ones are under consideration. Further, the U.S. NRC and the U.S. Department of Energy have initiated research into Light water reactor sustainability which is hoped will lead to allowing extensions of reactor licenses beyond 60 years, in increments of 20 years, provided that safety can be maintained, as the loss in non-CO2-emitting generation capacity by retiring reactors "may serve to challenge U.S. energy security, potentially resulting in increased greenhouse gas emissions, and contributing to an imbalance between electric supply and demand." In 2008, the International Atomic Energy Agency (IAEA) predicted that nuclear power capacity could double by 2030, though that would not be enough to increase nuclear's share of electricity generation.

Nuclear Power Plant in Bangladesh:

The Pakistan government undertook the nuclear power project in 1961 at Rooppur in Pabna and the land was acquired in 1963 even before France had its first nuclear power plant in 1964.France now gets 77 per cent of its total electricity from 55 nuclear plants, while Bangladeshs lone project area turned into a cattle grazing field although successive governments had no dearth of pledges to generate more power and explore new energy resources. The issue came up for discussion during each regime since then and soon fizzled out, allowing the project to roll from one government to another. The concerns that who will laugh the last matter most in leading the project to success as development of a nuclear electricity plant takes at least seven years longer than the five-year tenure of an elected government, and return to power for the second term in a row is not guaranteed as evident in election results since 1991. Unless the head of the government interferes properly, the project will not get momentum. There had been no major opposition from any quarter to Bangladeshs strides in installing nuclear reactors for power generation. Lack of political will and bureaucratic tangles held back the

45 project for decades. Bureaucrats are not directly involved in the process of research of nuclear science. They are not well equipped with information. Even then the scientists are to concede to their decisions. Almost every government endorsed the experts suggestion that early implementation of nuclear power project would add more value to national development as at least 30 countries are now considering nuclear power as a viable option for energy security. India and Pakistan generate 2 per cent of their electricity from nuclear reactors, while South Korea gets 29 per cent of its electricity from nuclear plants, Japan 25, United States 20, Russia 17 and United Kingdom 14 per cent. The governments conducted a number of feasibility studies and identified nuclear power generation appropriate and viable for Bangladesh both technically and economically. Meanwhile, the country obtained green signal from the International Atomic Energy Commission, apart from assurances of technical supports from a number of countries including France, Russia, USA, South Korea and China over the decades. In 1980, a 125MW plant was approved after a study that suggested for two units of 300MW nuclear plants. Pre-implementation phase activities for construction of the units on Rooppur site were done over the years by the BAEC with supports from the IAEA and other national organizations. Now the government hopes to get 1,100MW from nuclear reactors by 2015 to meet the growing power demands, though the work is yet to get desired pace. Bangladesh has signed all the treaties, protocols and conventions for required for developing nuclear energy and the IAEA has given green signal to go ahead with the project. Bangladesh would need further preparations for the project as it involved a lot of matters ranging from environmental aspects to reactors safety. It may seem difficult, but not impossible. Though the Rooppur site now looked ready, but it may take seven years to implement the project once the government signs contact with any reactor suppliers, Bangladesh has signed agreements with a few countries for cooperation for peaceful use of nuclear energy. Russia is the last country with which Bangladesh signed n MoU earlier this year. Asked whether Bangladesh would be able to begin project work by 2010, a joint secretary at the science and information technology ministry, who deals with the present negotiation with Russian authorities, expressed optimism. The site safety report by the international authorities for the proposed Rooppur plant was finalized early this decade and some additional investigation into hydrology, morphological analysis, subsoil

46 investigation, seismic studies and radiological dispersion were also carried out. The safety report was also updated. About reactors safety and probability of accidents, the third generation reactor has the highest safety mechanism with probability of one accident in a million year. For nuclear waste disposal, Bangladesh stands in a position for pursuing take back option, meaning that the reactor suppliers will take the high-level radioactive wastes back. Moreover, these substances are now being recycled to produce metal oxide fuel, which are considered commercial commodity nowadays. About the cost involvement in nuclear power plant, its initial cost is higher, but experiences in other countries say electricity production is cost effective in comparison to other natural resources. A successive government dithered in taking a positive decision on the nuclear power plant (NPP) issue. But, it is the credit to the successive governments that no decision had been taken without adequate consideration. Nuclear power plant cannot a prestige issue. The site in Rooppur in Pabna, surrounded by dense population, is not a suitable site. Most of the world's NPPs are either in coastal areas or in remote inland areas. Authorized discharges of radioactive liquid and gaseous wastes will affect surrounding population and cancer incidence will go up drastically. Another point is that under 'take back option', reactor supplier will take back high level wastes. It must be realized that the reactor vendor has nothing to do with radioactive wastes. It is the fuel supplier who may consider this take back option, but then it will contrary to the international treaty. But there is no decision about low and intermediate level wastes. Bangladesh would need at least 500 nuclear scientists for a 1,000 MW nuclear power plant for its operation and maintenance after its installation. Other than scientists, the BAEC is fully ready to work for setting up a nuclear power plant with its existing resources. It will get 4-5 years to take our own preparations following the signing of an agreement with any state for setting up a nuclear power plant. Bangladesh and Russia have signed in Moscow a protocol on cooperation on peaceful use of atomic energy. The Moscow protocol was signed in the backdrop of Bangladesh planning to opt for a nuclear power plant to meet the crippling shortage of electricity in the country.

47

Bibliography:
http://www.wikipedia.com

An entry to nuclear power through an educational discussion of reactors The Nuclear Energy Option, online book by Bernard L. Cohen. Steve Thomas (2005), "The Economics of Nuclear Power: analysis of recent studies"PDF (305 KB), PSIRU, University of Greenwich, UK Nuclear power information archives from ALSOS, the National Digital Science Library at Washington & Lee University. Texas Will Host First New U.S. Nuclear Plants since 1970s

http://library.thinkquest.org

48 http://visual.merriam-webster.com http://tonto.eia.doe.gov http://www.eia.doe.gov/kids/energyexplained/sources/non-renewable/nuclear.html http://www.google.com/images