MANUAL

LEO 5

Keller AG für Druckmesstechnik

 www.keller-druck.com

Index

1 General information ..................................................................3

2 Operating instructions ...............................................................3
2.1 Touch Display..................................................................3
2.2 Manage the device with touch pannels............................4
2.2.1 Example: Setting the peak mode ................................5
2.2.2 Handling example: How to stop the peak mode..........5
2.3 Menu structure.................................................................6
2.3.1 Main menu..................................................................6
2.3.2 Sub menu ...................................................................7
2.3.3 Sub menu settings ....................................................10
2.4 USB connection.............................................................12
2.5 Installing the USB – driver LEO 5 ..................................13
2.6 Optional – establish a Bluetooth connection..................17
2.7 Charge accumulator ......................................................20
3 Disposal ..................................................................................20
4 General Safety Instructions.....................................................21
 www.keller-druck.ch

1 General information
The LEO 5 is powered by accumulator and will be
charged when connected to USB Port. As the
accumulator is fix built in the device it cannot be
replaced.

2 Operating instructions
2.1 Touch Display

LEO 5 has two keys integrated into the display.

A key press is initiated by touching the key field

“SELECT” or “ENTER” and activated by release the
key for at least 0.5 second.

(release your finger from the display after touching,

for at least 1cm away from the display field)

Turn-on:
Touching the “SELECT” key turns on the display.
The device displays “PRESS ENTER”.
Touch “ENTER” to start the manometer.

-3-
 www.keller-druck.ch

2.2 Manage the device with touch

pannels

choose different functions

press „SELECT“

activate commands or functions

press “ENTER”

Remark: The display automatically switches back to

the main display 10 seconds after the last key
touch.

-4-
 www.keller-druck.ch

2.2.1 Example: Setting the peak mode

Turn on the instrument by pressing the

SELECT key followed by pressing the
ENTER key
Press the “SELECT”–key 3 times: The
lower display part will show “MENU”
Press “ENTER”
Press “SELECT” ”–key 3 times: The lower
display part will show “PEAK” and
“START”
Press “ENTER”: In the main display, the
segment “PEAK” indicates that the peak
mode is on.

2.2.2 Handling example: How to stop the

peak mode

Press “SELECT”–key 3 times: The lower

display part will show “MENU”
Press “ENTER”
Press “SELECT”–key 3 times: The lower
display part will show “PEAK” and “STOP”
Press “ENTER”

-5-
 www.keller-druck.ch

2.3 Menu structure

2.3.1 Main menu

Main Display

Reset
Min.-/Max.-value are set to
the actual pressure

OFF
Turns off the instrument
and ends an active record

Menu
Releases the sub menu
functions

-6-
 www.keller-druck.ch

2.3.2 Sub menu

Rec On
Starts a record with the
actual configuration
(set via the software)

Rec OFF
Ends an active record

Peak START
PEAK off: Normal measuring mode with
2 measurements per second.
PEAK on: Fast measuring mode with
5000 measurements per second

RF BT On/OFF
Switch the LEO 5 Bluetooth modul
“On” or “OFF” to communicate
wireless

-7-
 www.keller-druck.ch

Zero SET
Sets a new pressure
zero reference

Zero RESET
Sets the pressure zero to
factory setting

UNIT
Unit selection

CONT
Activates or deactivates
the automatic turn off function

Display
Main display selection

-8-
 www.keller-druck.ch

BACKL
Backlight setting

RESL
Choose resolution

ACCU
Accumulator information
and charge status

EXIT
Each sub menu can be left
by pressing “ENTER” while
“EXIT” is displayed.
The display will switch back
to the sub menu

-9-
 www.keller-druck.ch

2.3.3 Sub menu settings

Unit selection Continuous Display selection

mode

↓ ↓ ↓

bar, mbar, hPa, CONT on: select the lower

kPa, MPa, PSI, Deactivates the display option.
2
kp/cm , cmH2O, automatic turn-off Select between:
mH2O, inH2O, function.
ftH2O, mmHg, inHg temperature display
CONT off: or
Activates the min/max pressure
automatic turn off value
function (the
instrument turns off
15 minutes after the
last key operation)

- 10 -
 www.keller-druck.ch

Backlight setting Resolution Accu information Exit

selection

↓ ↓

The backlight can set measurement displays sub menu can be

be turn “ON”, “OFF” value resolution accumulator voltage left by pressing
or “ONOFF” between 0 to 4 and visualizes the “ENTER” while
decimal places charge level. “EXIT” is displayed.
“ONOFF” 3.2 Volt is an empty The display will
turn on the backlight - 4.2 Volt is a fully switch back to the
for 10 seconds after charged main menu
key is pressed accumulator

- 11 -
 www.keller-druck.ch

2.4 USB connection

To connect the device to USB, remove the backside
mounted rubber protection to access the USB plug.

Hint:
The rubber also acts as over pressure safety valve
in case of damages at the pressure sensor when
inner pressure is raised to a critical pressure.

- 12 -
 www.keller-druck.ch

2.5 Installing the USB – driver LEO 5

To enable the USB communication you have to

install the manually the LEO5 USB – driver.

Connect the LEO5 with the PC by a USB cable.

After the PC has detected this device the following
message will appear: "USB Device not recognized"

Link to the driver:

http://www.keller-druck2.ch/swupdate
/DriverManometer/DriverManometer.zip

Open the device manager and do a right click on

the new listed device and select update driver as
shown in the picture.

- 13 -
 www.keller-druck.ch

Please follow the introduction shown in the picture

to install the driver.

choose the path where the driver is stored.

- 14 -
 www.keller-druck.ch

The Computer starts to install the new driver.

Windows doesn’t recognize the driver.

Please click on “Continue Anyway”.

- 15 -
 www.keller-druck.ch

Now the driver is installed and the device is

recognized windows. The device manager is listing
the device as “Manometer” with assigned comport
number.

This com port number must be select manually in

the PC software.

Remark:

If the device is
connected to USB
and is switched
OFF, the device will
not be listed in the
device manager

- 16 -
 www.keller-druck.ch

2.6 Optional – establish a Bluetooth

connection

Make sure your Computer has a Bluetooth Module

integrated or it is connected to a Bluetooth USB
Dongle, which is activated.

Your module must be capable with Bluetooth 2.1.

Step 1: check/activate Bluetooth on your PC

To activate your Bluetooth device, open the Device
Manager and go to the section Bluetooth.
Perform a right click on the Bluetooth device.
If the Bluetooth is ready to use the device status
shows “This device is working properly”.
Otherwise please activate the Bluetooth device.
(see picture 1.1)

Step 2: switch the LEO 5 Bluetooth module on

Switch the LEO 5 Bluetooth module on. More
information in the chapter menu structure.

Step 3: establish Bluetooth connection

To establish a connection with the LEO 5, open the
window “Devices and Printers” and select “Add a
device”. (see picture 1.2)

- 17 -
 www.keller-druck.ch

picture 1.1

picture 1.2

- 18 -
 www.keller-druck.ch

Step 4: search device LEO 5

Wait until the LEO 5 is found.
The name from the LEO 5 is “Manometer” and the
serial number. If device is not found, search again
until the device is listed in the window.

May it takes a few tries to detect the device.

After the LEO 5 is found, select it and click on the
“Next” button.

- 19 -
 www.keller-druck.ch

Step 5: Confirm the pass code

The LEO 5 will send a pass code. If you want to
establish the Bluetooth connection, you have to
accept the pass code. After this, you will see a
window that confirm the established Bluetooth
connection.

2.7 Charge accumulator

To charge the accumulator, connected the device

via USB to a PC or USB main adaptor.

Check the charge status with sub menu

"Accumulator" on LEO5 or read charge status with
the PC software.

3 Disposal
This product must not be disposed
of as normal household waste at the
end of its useful lifetime. To prevent
possible damage to the environment
or to health due to uncontrolled
waste disposal, this product must be
separated from other waste and
recycled correctly in order to ensure
sustainable use of the raw materials.

- 20 -
 www.keller-druck.ch

4 General Safety Instructions

When installing and operating the digital
manometer, attention must be paid to the
corresponding safety regulations.

Only mount the digital manometer onto

unpressurized systems.

On pressure ranges ≥61 bar, the pressure

connections could show residual hydraulic oil,
determined by production flow.

Please also note the corresponding data sheet.

- 21 -