Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 1 of 38

S P E C I F I C AT I O N S
Customer
Product Name Wire Wound Molded SMD Power Inductors
Sunlord Part Number MWSA-S Series
Customer Part Number
[ New Released, Revised] SPEC No.: ES017-07
【This SPEC is total 38 pages including specifications and appendix.】
【ROHS Compliant Parts】

Approved By Checked By Issued By

Shenzhen Sunlord Electronics Co., Ltd.

Address: Sunlord Industrial Park, Dafuyuan Industrial Zone, Guanlan, Shenzhen, China 518110
Tel: 0086-755-29832660 Fax: 0086-755-82269029 E-Mail: [email protected]

【For Customer approval Only】 Date:

Qualification Status: Full Restricted Rejected
Approved By Verified By Re-checked By Checked By

Comments:
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 2 of 38

【Version change history】

Rev. Effective Date Changed Contents Change Reasons Approved By

01 Jan.11, 2019 New release / Simei Yu

The number of MWSA0618S

02 April.30, 2019 products per reel was changed from / Simei Yu

2000 to 1500

03 October 24, 2019 Performance Graphs Customer requirements Simei Yu

Increase the Max value of the

04 October 29, 2019 saturation current and heat rating Customer requirements Simei Yu
current

05 Dec 12, 2019 Add curves of 0604 / 0605 series Customer requirements Simei Yu

Add 0604s series model：

R68/1R0/1R5/3R3/6R8/100/220/330/

06 Apr 15, 2020 470 Customer requirements Simei Yu

Modify the size of 0604s series belt
wheel

Caution：
All products listed in this specification are developed, designed and intended for use in general electronics equipment. The products are not
designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require especially high
reliability, or whose failure, malfunction or trouble might directly cause damage to society, person, or property. Please understand that we are
not responsible for any damage or liability caused by use of the products in any of the applications below. Please contact us for more details if
you intend to use our products in the following applications.
1. Aircraft equipment
2. Aerospace equipment
3. Undersea equipment
4. nuclear control equipment
5. military equipment
6. Power plant equipment
7. Medical equipment
8. Transportation equipment (automobiles, trains, ships,etc.)
9. Traffic signal equipment
10. Disaster prevention / crime prevention equipment
11. Data-processing equipment
12. Applications of similar complexity or with reliability requirements comparable to the applications listed in the above
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 3 of 38
1. Scope
This specification applies to MWSA-S series of wire wound molded SMD power Inductors

2. Product Description and Identification (Part Number)

1) Description
Wire Wound Molded SMD Type Power Inductor, MWSAXXXX, XX μH± X% @XXX KHz/XXXV, XXXmΩ, XXXm A.
2) Product Identification (Part Number)
MWSA XXXXX -XXX □ T
① ② ③ ④ ⑤

① Type ② External Dimensions (mm)

Wire wound molded SMD power 0412S~1206S
MWSA
Inductors

③ Nominal Inductance ④ Inductance Tolerance

Example Nominal Value M ±20%

1R0 1.0μH

100 10μH
⑤ Packing
101 100μH
T Tape Carrier Package

3. Electrical Characteristics
Please refer to Appendix A.
1) Operating temperature range (Including self-heating): -55℃~+125℃.
2) Storage temperature and humidity range (product with tapping ): -10℃~+40℃, RH 70% Max.
4. Shape and Dimensions
1) Dimensions and recommended PCB pattern for reflow soldering: See Fig.4-1 and Table 4-1.

Unit: mm

Series A B C D E I Typ. J Typ. H Typ.

MWSA0412S 4.2±0.25 4.4±0.35 1.0±0.2 0.8±0.3 2.0±0.3 1.5 2.2 2.5

MWSA0402S 4.2±0.25 4.4±0.35 1.8±0.2 0.8±0.3 2.0±0.3 1.5 2.2 2.5

MWSA0518S 5.2±0.2 5.4±0.35 1.6±0.2 1.20±0.2 2.2±0.3 1.9 2.2 2.5

MWSA0503S 5.2±0.2 5.4±0.35 2.8±0.2 1.20±0.2 2.2±0.3 1.9 2.2 2.5

MWSA0618S 6.6±0.2 7.0±0.3 1.6±0.2 1.60±0.3 3.0±0.3 2.35 3.7 3.5

MWSA0624S 6.6±0.2 7.0±0.3 2.2±0.2 1.60±0.3 3.0±0.3 2.35 3.7 3.5

MWSA0603S 6.6±0.2 7.0±0.3 2.8±0.2 1.60±0.3 3.0±0.3 2.35 3.7 3.5

MWSA0604S 6.6±0.2 7.0±0.3 3.8±0.2 1.60±0.3 3.0±0.3 2.35 3.7 3.5

MWSA0605S 6.6±0.2 7.0±0.3 4.8±0.2 1.60±0.3 3.0±0.3 2.35 3.7 3.5

MWSA1004S 10.0±0.3 11.5Max 3.8±0.2 2.0±0.5 3.0±0.5 4.1 5.4 4.1

MWSA1204S 12.8±0.5 13.45±0.35 4.0Max. 2.0±0.5 See Remarks 3.25 8.0 5.5

MWSA1205S 12.6±0.3 13.45±0.35 4.8±0.2 2.0±0.5 See Remarks 3.25 8.0 5.5

MWSA1206S 12.6±0.3 13.45±0.35 5.8±0.2 2.0±0.5 5.0±0.3 3.25 8.0 5.5

 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 4 of 38
Remarks:

Series E(mm) Dimensions

3.85±0.5 R22/R47
MWSA1204S
5.0±0.3 R68/R82/1R0/1R5/2R2/3R3/4R7/6R8/100/150/220

3.85±0.5 R22/R36/R50/R68/R82/1R0/1R5/2R2
MWSA1205S
5.0±0.3 3R3/4R7/6R8/100/150/220/330/470

Structure and Components: See Table 4-2 [

Table 4-2

Symbol Components Material

a Marking Ink(black)
b Core Alloy Sponge Powder
c Wire Polyurethane copper wire

d Terminal Copper plated with Sn

5. Test and Measurement Procedures

5.1 Test Conditions
5.1.1 Unless otherwise specified, the standard atmospheric conditions for measurement/test as:
a. Ambient Temperature: 20±15℃
b. Relative Humidity: 65±20%
c. Air Pressure: 86 KPa to 106 KPa
5.1.2 If any doubt on the results, measurements/tests should be made within the following limits:
a. Ambient Temperature: 20±2℃
b. Relative Humidity: 65±5%
c. Air Pressure: 86KPa to 106 KPa
5.2 Visual Examination
a. Inspection Equipment: 10 X magnifier
5.3 Electrical Test
5.3.1 DC Resistance (DCR)
a. Refer to Appendix A.
b. Test equipment (Analyzer): HIOKI3540 or equivalent.
5.3.2 Inductance (L)
a. Refer to Appendix A.
b. Test equipment: Wayne kerr3260+3265B or equivalent.
5.3.3 Rated Current
a. Refer to Appendix A.
b. Test equipment: Wayne kerr3260+3265B, Agilent E3633A, R2M-2H3 or equivalent.
c. Definition of Rated Current (Ir): With the condition of the DC current pass, the inductance decrease approximate 30% of
the standard value, compare to the temperature rise approximate 40℃, the smaller is Rated Current.(reference
environment temperature:20℃)
5.4 Reliability Test

Mechanical Reliability

Item Specification and Requirement Test Method

The surface of terminal immersed shall be Solder heat proof:

Solderability minimum of 95% covered with a new coating of 1. Preheating: 160 ± 10 ℃
solder 2. Retention time: 245 ± 5 ℃ for 2 ± 0.5 seconds
1. Vibration frequency:
(10 Hz to 55 Hz to 10Hz) in 60 seconds as a period
Inductance change: Within ± 10% Without 2. Vibration time:
Vibration
mechanical damage such as break Period cycled for 2 hours in each of 3 mutual perpendicular
directions.
3. Amplitude: 1.5 mm max.
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 5 of 38
1. Peak value: 100 G
Inductance change: Within ± 10% Without 2. Duration of pulse: 11ms
Shock
mechanical damage such as break 3. 3 times in each positive and negative direction of 3 mutual
perpendicular directions

Endurance Reliability

Item Specification and Requirement Test Method

1. Repeat 100 cycles as follow:

(-55 ± 2 ℃; 30 ± 3 min)
→(Room temp., 5 min)
Inductance change: Within ± 10% Without distinct
Thermal Shock → (+125 ± 2 ℃, 30 ± 3 min)
damage in appearance
→ (Room temp., 5 min)
2. Recovery: 48 + 4 / -0 hours of recovery under the standard
condition after the test.

1. Environment condition: 85 ± 2 ℃
High Temperature Inductance change: Within ± 10% Without distinct
Applied Current: Rated current
Resistance damage in appearance
2. Duration: 1000 + 4 / -0 hours

1. Environment condition: 60 ± 2 ℃
Humidity Inductance change: Within ±10% Without distinct Humidity: 90–95%
Resistance damage in appearance Applied Current: Rated current
2. Duration: 1000 + 4 / -0 hours

Low Temperature Inductance change: Within ± 10% Without distinct Store temperature:
Store damage in appearance -55 ± 2 ℃,1000 + 4 / -0 hours
High Temperature Inductance change: Within ± 10% Without distinct Store temperature:
Store damage in appearance +125 ± 2 ℃,1000 + 4 / -0 hours
6. Packaging, Storage and Transportation
6.1 Tape Carrier Packaging:
Packaging code: T
(1) Tape carrier packaging are specified in attached figure Fig.6.1-1~2
(2) Tape carrier packaging quantity:

Standard Quantity Standard Quantity

Type Type
(pcs/reel) (pcs/reel)

MWSA0412S 3000 MWSA0604S 1000

MWSA0402S 3000 MWSA0605S 1000
MWSA0518S 2000 MWSA1004S 500
MWSA0503S 2000 MWSA1204S 500
MWSA0618S 1500 MWSA1205S 500
MWSA0624S 1500 MWSA1206S 500
MWSA0603S 1500 - -

a. Taping Drawings (Unit: mm)

Fig.6.1-1
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 6 of 38
b.Reel and Taping Dimensions (Unit: mm)

Fig.6.1-2

Reel dimensions (mm) Tape dimensions (mm)

Type
A N C W W0 P P0 H T A0 B0
12.4± 1.5± 0.30±
MWSA0412S 330±2.0 100±2.0 13±1.0 12±0.3 8±0.1 4±0.1 4.4±0.1 4.9±0.1
2.0 0.05 0.05
12.4± 2.3± 0.35±
MWSA0402S 330±2.0 100±2.0 13±1.0 12±0.3 8±0.1 4±0.1 4.4±0.1 4.9±0.1
2.0 0.05 0.05
12.4± 2.1± 0.35±
MWSA0518S 330±2.0 100±2.0 13±1.0 12±0.3 8±0.1 4±0.1 5.4±0.1 5.9±0.1
2.0 0.05 0.05
12.4± 3.3± 0.35±
MWSA0503S 330±2.0 100±2.0 13±1.0 12±0.3 8±0.1 4±0.1 5.4±0.1 5.9±0.1
2.0 0.05 0.05
16.4± 2.1± 0.35±
MWSA0618S 330±2.0 100±2.0 13±1.0 16±0.3 12±0.1 4±0.1 6.9±0.1 7.5±0.1
2.0 0.05 0.05
16.4± 2.7± 0.35±
MWSA0624S 330±2.0 100±2.0 13±1.0 16±0.3 12±0.1 4±0.1 6.9±0.1 7.5±0.1
2.0 0.05 0.05
16.4± 3.3± 0.35±
MWSA0603S 330±2.0 100±2.0 13±1.0 16±0.3 12±0.1 4±0.1 6.9±0.1 7.5±0.1
2.0 0.05 0.05
13.2± 16.8± 4.2± 0.35±
MWSA0604S 330±2.0 97±0.5 16±0.3 12±0.1 4±0.1 6.9±0.1 7.5±0.1
0.2 2.0 0.10 0.05
16.4± 5.2± 0.4±
MWSA0605S 330±2.0 100±2.0 13±1.0 16±0.3 12±0.1 4±0.1 6.9±0.1 7.5±0.1
2.0 0.10 0.05
24.4± 4.3± 0.35± 10.4± 11.5±
MWSA1004S 330±2.0 100±2.0 13±1.0 24±0.3 16±0.1 4±0.1
2.0 0.10 0.05 0.1 0.1
24.4± 4.3± 0.5± 13.4± 14.4±
MWSA1204S 330±2.0 100±2.0 13±1.0 24±0.3 16±0.1 4±0.1
2.0 0.10 0.05 0.1 0.1
24.4± 5.3± 0.5± 13.2± 14.4±
MWSA1205S 330±2.0 100±2.0 13±1.0 24±0.3 16±0.1 4±0.1
2.0 0.10 0.05 0.1 0.1
24.4± 6.3± 0.5± 13.2± 14.4±
MWSA1206S 330±2.0 100±2.0 13±1.0 24±0.3 16±0.1 4±0.1
2.0 0.10 0.05 0.1 0.1

c.Peeling off force: 10gf to 130gf in the direction show below.

Top tape or cover tape
1650~ 1800

Base tape Fig. 6.1-4

6.2 Storage
(1) The solderability of the external electrodes may deteriorate if packages are stored in high humidity. Besides, to ensure packing
material’s good state, packages must be stored at -10℃ to 40℃ and 70% RH Max.
(2) The solderability of the external electrodes may deteriorate if packages are exposed to dust of harmful gas (e.g. HCl, sulfurous gas of
H2S).
(3) Packaging materials may deform if packages are exposed directly to sunlight.
(4) Minimum packages, such as polyvinyl heat-seal packages shall not be opened until they are used. If opened, use the reels as soon
as possible.
(5) Solderability shall be guaranteed for a period of time from the date of delivery on condition that they are stored at the specified
environment. For those parts, which passed more than the time shall be checked solderability before using.
(6) For magnetic products, keep clear of anything that may generate magnetic fields to avoid change of products performance.
(7) To avoid any damage to products, do not load mechanic force on products or place heavy goods on products, and exclude strong
vibration or drop.
(8)In case of storage over 12 months, solderability shall be checked before actual usage.
7. Warning and Attentions
7.1 Precautions on Use
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 7 of 38
(1) Always wear static control bands to protect against ESD.
(2) Any devices used with the products (soldering irons, measuring instruments) should be properly grounded.
(3) Keep bare hands and metal conductors (i.e., metal desk) away from electrodes or conductive areas that lead to electrodes.
(4) Preheat when soldering.
(5) Don’t apply current in excess of the rated current value. It may reduce the impedance or inductance, or cause damage to
components due to over-current.
(6) For magnetic products, keep clear of anything that may generate magnetic fields such as speakers and coils. Use non-magnetic
tweezers when handing the chips.
(7) When soldering, the electrical characteristics may be varied due to hot energy and mechanical stress.
(8) When coating products with resin, the relatively high resin curing stress may change the electrical characteristics. For exterior
coating, select resin carefully so that electrical and mechanical performance of the product is not affected. Before using, please
evaluate reliability with the product mounted in your application set.
(9) When mount chips with adhesive in preliminary assembly, do appropriate check before the soldering stage, i.e., the size of land
pattern, type of adhesive, amount applied, hardening of the adhesive on proper usage and amounts of adhesive to use.
(10) Mounting density: Add special attention to radiating heat of products when mounting other components nearby. The excessive heat
by other products may cause deterioration at joint of this product with substrate.
(11) Since some products are constructed like an open magnetic circuit, narrow spacing between components may cause magnetic
coupling.
(12) Please do not give the product any excessive mechanical shocks in transportation.
(13) Please do not touch wires by sharp terminals such as tweezers to avoid causing any damage to wires.
(14) Please do not add any shock and power to the soldered product to avoid causing any damage to chip body.
(15) Please do not touch the electrodes by naked hand as the solderability of the external electrodes may deteriorate by grease or oil on
the skin.
7.2 PCB Bending Design
The following shall be considered when designing and laying out PCB’s.
(1) PCB shall be designed so that products are not subjected to the mechanical stress from board warp or deflection.

Products shall be located in

the sideways direction to
the mechanical stress
(Poor example) (Good example)
(2) Products location on PCB separation.

C Product shall be located carefully because they may

B
Seam be subjected to the mechanical stress in order of A>C=B>D.

A D

(3) When splitting the PCB board, or insert (remove) connector, or fasten thread after mounting components, care is required so as not to
give any stress of deflection or twisting to the board. Because mechanical force may cause deterioration of the bonding strength of
electrode and solder, even crack of product body. Board separation should not be done manually, but by using appropriate devices.
7.3 Recommended PCB Design for SMT Land-Patterns
When chips are mounted on a PCB, the amount of solder used (size of fillet) can directly affect chip performance. Therefore, the following
items must be carefully considered in the design of solder land patterns:
(1) The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or cracking.
Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder pads which in
turn determines the amount of solder necessary to form the fillets.
(2) When more than one part is jointly soldered onto the same land or pad, the pad must be designed that each component’s soldering
point is separated by solder-resist.
Recommended land dimensions please refer to product specification.
8 Recommended Soldering Technologies
8.1Re-flowing Profile: Peak 260℃ max
260℃
△ Preheat condition: 150 ~200℃/60~120sec.
△ Allowed time above 217℃: 60~90sec.
Max Ramp Up Rate=3℃/sec.
△ Max temp: 260℃ 217℃
Max Ramp Down Rate=6℃/sec.
△ Max time at max temp: 10sec.
60～90sec.
△ Solder paste: Sn/3.0Ag/0.5Cu 200℃
△ Allowed Reflow time: 2x max
150℃
Please refer to Fig. 8.1
60～120sec.
[Note: The reflow profile in the above table is only for
qualification and is not meant to specify board assembly 25℃
Time 25℃ to Peak =8 min max
profiles. Actual board assembly profiles must be based on
the customer's specific board design, solder paste and process, Fig. 8.1
and should not exceed the parameters as the Reflow profile shows.]
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 8 of 38
8.2 Iron Soldering Profile
△ Iron soldering power: Max. 30W 3sec. Max.
△ Pre-heating: 150℃/60sec.
△ Soldering Tip temperature: 350℃ Max. 350℃
Soldering Iron
△ Soldering time: 3sec. Max.
△ Solder paste: Sn/3.0Ag/0.5Cu Power: max. 30W
△ Max.1 times for iron soldering
Diameter of Soldering
Please refer to Fig. 8.2.
[Note: Take care not to apply the tip of Iron 1.0mm max.
the soldering iron to the terminal electrodes.] Tc ℃
8.3 Recommended Soldering Technologies
Heat Gun Profile Fig. 8.2.
△ Soldering tip temperature: 350℃ Max.
△ Hot air time: <5sec (over 5sec may cause wiring inductor short)
△ When repairing or reworking the component near inductors, take over-heat protection for
Inductors
9. Solder Volume
Solder shall be used not to exceed as shown below. Exceeding solder volume may cause the failure of mechanical or electrical performance.

0 ≤L≤T
(T: height of electrode)

10. Supplier Information

a) Supplier:
Shenzhen Sunlord Electronics Co., Ltd.
b) Manufacturer:
Shenzhen Sunlord Electronics Co., Ltd.
c) Manufacturing Address:
Sunlord Industrial Park, Dafuyuan Industrial Zone, Guanlan, Shenzhen, China
Zip: 518110
Appendix A: Electrical Characteristics
MWSA0412S Series
Inductance DC Resistance Saturation Current*3 Heat Rating Current*4
Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0412S-R15MT 0.15±20% 9 12.00 15.00 6.80 7.50

MWSA0412S-R22MT 0.22±20% 11 8.80 11.00 6.50 7.00

MWSA0412S-R33MT 0.33±20% 19 6.70 8.40 5.70 6.50

MWSA0412S-R47MT 0.47±20% 21 5.40 6.80 5.20 6.00

MWSA0412S-R68MT 0.68±20% 36 4.80 6.00 4.20 4.70

MWSA0412S-1R0MT 1.0±20% 47 4.40 5.50 3.80 4.50

MWSA0412S-1R5MT 1.5±20% 75 3.20 4.00 2.70 3.25

MWSA0412S-2R2MT 2.2±20% 83.5 2.40 3.00 2.20 2.75

MWSA0412S-4R7MT 4.7±20% 195 1.80 2.20 1.45 1.80

MWSA0402S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0402S-R10MT 0.10±20% 4 17.60 22.00 11.20 13.00

MWSA0402S-R22MT 0.22±20% 6.6 10.00 12.50 8.20 9.50

MWSA0402S-R33MT 0.33±20% 11 9.60 12.00 8.60 10.00

MWSA0402S-R47MT 0.47±20% 14 7.60 9.50 6.65 7.50

MWSA0402S-R56MT 0.56±20% 16 7.20 9.00 6.10 7.00

 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 9 of 38

MWSA0402S-R68MT 0.68±20% 18 6.40 8.00 6.15 7.00

MWSA0402S-1R0MT 1.0±20% 27 5.60 7.00 5.40 6.00

MWSA0402S-1R2MT 1.2±20% 27 5.20 6.50 5.40 6.00

MWSA0402S-1R5MT 1.5±20% 46 4.40 5.50 4.30 5.00

MWSA0402S-2R2MT 2.2±20% 58 4.00 5.00 3.80 4.50

MWSA0402S-3R3MT 3.3±20% 87 2.80 3.50 2.80 3.30

MWSA0402S-4R7MT 4.7±20% 105 2.40 3.00 2.20 2.80

MWSA0402S-6R8MT 6.8±20% 175 2.00 2.50 1.90 2.40

MWSA0402S-100MT 10±20% 282 1.60 2.00 1.30 1.60

MWSA0402S-220MT 22±20% 363 1.12 1.40 0.90 1.20

MWSA0518S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0518S-R47MT 0.47±20% 9 9.60 12.00 9.50 10.50

MWSA0518S-R56MT 0.56±20% 10 8.80 11.00 8.20 9.50

MWSA0518S-1R0MT 1.0±20% 17 7.20 9.00 7.20 8.00

MWSA0518S-1R5MT 1.5±20% 26 6.40 8.00 6.60 7.50

MWSA0518S-2R2MT 2.2±20% 35 4.80 6.00 4.20 5.00

MWSA0518S-3R3MT 3.3±20% 58 3.84 4.80 3.80 4.50

MWSA0518S-4R7MT 4.7±20% 85 3.20 4.00 3.00 3.50

MWSA0518S-6R8MT 6.8±20% 120 2.72 3.40 2.40 2.80

MWSA0518S-100MT 10±20% 155 2.00 2.50 2.20 2.50

MWSA0503S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0503S-R10MT 0.10±20% 3.0 24.00 30.00 23.00 25.00

MWSA0503S-R20MT 0.20±20% 3.9 16.00 20.00 13.00 14.00

MWSA0503S-R33MT 0.33±20% 5.5 14.40 18.00 13.10 14.00

MWSA0503S-R47MT 0.47±20% 8.5 12.00 15.00 10.00 11.00

MWSA0503S-R68MT 0.68±20% 12 9.20 11.50 8.20 9.00

MWSA0503S-1R0MT 1.0±20% 14 8.00 10.00 7.80 8.50

MWSA0503S-1R2MT 1.2±20% 16 7.60 9.50 7.85 8.50

MWSA0503S-1R5MT 1.5±20% 25 7.20 9.00 7.60 8.20

MWSA0503S-2R2MT 2.2±20% 29 5.60 7.00 6.40 7.00

MWSA0503S-3R3MT 3.3±20% 38 4.80 6.00 5.50 5.50

MWSA0503S-4R7MT 4.7±20% 60 3.68 4.60 4.00 4.50

MWSA0503S-6R8MT 6.8±20% 90 2.88 3.60 2.90 3.50

MWSA0503S-100MT 10±20% 125 2.80 3.50 2.80 3.20

MWSA0618S Series
Heat Rating Current*4
Inductance DC Resistance Saturation Current *3
Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 10 of 38
Symbol L DCR Isat Irms

MWSA0618S-R10MT 0.10±20% 2.3 30.40 38.00 23.00 25.00

MWSA0618S-R22MT 0.22±20% 3.5 19.20 24.00 20.00 22.00

MWSA0618S-R47MT 0.47±20% 8.4 14.40 18.00 10.00 11.50

MWSA0618S-R68MT 0.68±20% 12 13.20 16.50 8.40 9.50

MWSA0618S-1R0MT 1.0±20% 16 9.60 12.00 7.60 8.50

MWSA0618S-1R5MT 1.5±20% 26 7.36 9.20 7.10 8.00

MWSA0618S-2R2MT 2.2±20% 35 6.40 8.00 6.20 7.00

MWSA0618S-3R3MT 3.3±20% 50 4.80 6.00 3.80 4.50

MWSA0618S-4R7MT 4.7±20% 62 4.00 5.00 3.50 4.00

MWSA0618S-6R8MT 6.8±20% 110 3.60 4.50 2.40 3.00

MWSA0618S-100MT 10±20% 155 3.20 4.00 1.95 2.30

MWSA0618S-220MT 22±20% 350 1.84 2.30 1.40 1.80

MWSA0624S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0624S-R22MT 0.22±20% 3 24.00 30.00 19.00 21.00

MWSA0624S-R33MT 0.33±20% 4.1 19.60 24.50 16.00 18.00

MWSA0624S-R47MT 0.47±20% 5.1 16.00 20.00 13.50 15.00

MWSA0624S-R56MT 0.56±20% 6.5 13.60 17.00 11.50 13.00

MWSA0624S-R68MT 0.68±20% 7 12.80 16.00 10.50 12.00

MWSA0624S-1R0MT 1.0±20% 13.5 12.00 15.00 8.00 9.00

MWSA0624S-1R5MT 1.5±20% 20 10.80 13.50 7.00 8.20

MWSA0624S-2R2MT 2.2±20% 28 8.00 10.00 6.20 7.00

MWSA0624S-3R3MT 3.3±20% 39 6.40 8.00 4.80 5.50

MWSA0624S-4R7MT 4.7±20% 50 5.20 6.50 4.30 5.00

MWSA0624S-6R8MT 6.8±20% 70 4.80 6.00 3.20 4.00

MWSA0624S-100MT 10±20% 101 3.20 4.00 2.40 3.10

MWSA0624S-150MT 15±20% 160 2.64 3.30 2.00 2.50

MWSA0624S-220MT 22±20% 230 2.00 2.50 1.60 2.00

MWSA0603S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0603S-R22MT 0.22±20% 3 27.20 34.00 21.00 24.00

MWSA0603S-R33MT 0.33±20% 3.5 20.00 25.00 19.00 21.00

MWSA0603S-R47MT 0.47±20% 4.1 16.00 20.00 16.50 18.00

MWSA0603S-R56MT 0.56±20% 4.5 14.40 18.00 15.00 16.50

MWSA0603S-R68MT 0.68±20% 5.3 13.60 17.00 14.50 16.00

MWSA0603S-R82MT 0.82±20% 6.0 12.80 16.00 12.50 14.00

MWSA0603S-1R0MT 1.0±20% 7.4 12.00 15.00 10.50 12.00

MWSA0603S-1R5MT 1.5±20% 12.1 9.60 12.00 10.50 12.00

MWSA0603S-2R2MT 2.2±20% 15 8.00 10.00 8.50 9.50

MWSA0603S-3R3MT 3.3±20% 22 7.60 9.50 7.50 8.50

 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 11 of 38

MWSA0603S-4R7MT 4.7±20% 33 7.20 9.00 5.00 6.00

MWSA0603S-5R6MT 5.6±20% 42 5.20 6.50 4.80 5.50

MWSA0603S-6R8MT 6.8±20% 48 4.80 6.00 4.20 5.00

MWSA0603S-8R2MT 8.2±20% 60 4.40 5.50 4.20 5.00

MWSA0603S-100MT 10±20% 68 4.40 5.50 3.80 4.50

MWSA0603S-150MT 15±20% 113 3.20 4.00 2.30 3.00

MWSA0603S-220MT 22±20% 170 2.40 3.00 2.00 2.50

MWSA0603S-330MT 33±20% 270 2.00 2.50 1.60 2.00

MWSA0603S-470MT 47±20% 385 1.60 2.00 1.20 1.50

MWSA0604S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0604S-R68MT 0.68±20% 4.8 / 19.0 / 17.0

MWSA0604S-1R0MT 1.0±20% 6.6 / 16.0 / 13.5

MWSA0604S-1R5MT 1.5±20% 10 / 12.5 / 12.4

MWSA0604S-2R2MT 2.2±20% 14 8.80 11.00 7.80 10.0

MWSA0604S-3R3MT 3.3±20% 20 / 9.5 / 8.5

MWSA0604S-4R7MT 4.7±20% 30 7.20 9.00 6.00 6.50

MWSA0604S-6R8MT 6.8±20% 45 / 6.5 / 5.5

MWSA0604S-100MT 10±20% 65 / 6.0 / 4.8

MWSA0604S-100MTB01 10±20% 63 / 6.5 / 5.0

MWSA0604S-150MT 15±20% 95 3.60 4.50 2.80 3.70

MWSA0604S-220MT 22±20% 125 / 4.0 / 3.3

MWSA0604S-330MT 33±20% 240 / 3.0 / 2.2

MWSA0604S-470MT 47±20% 320 / 2.5 / 1.8

MWSA0605S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA0605S-R47MT 0.47±20% 3.9 16.80 21.00 17.00 20.00
MWSA0605S-R68MT 0.68±20% 4.5 14.40 18.00 14.50 16.50
MWSA0605S-1R0MT 1.0±20% 6.6 12.80 16.00 10.00 12.00
MWSA0605S-1R5MT 1.5±20% 10 10.40 13.00 8.20 9.50
MWSA0605S-2R2MT 2.2±20% 12.5 8.80 11.00 8.00 9.00
MWSA0605S-3R3MT 3.3±20% 22 8.00 10.00 7.60 8.50
MWSA0605S-4R7MT 4.7±20% 29 6.40 8.00 5.00 6.00
MWSA0605S-6R8MT 6.8±20% 41 5.04 6.30 4.00 5.80
MWSA0605S-8R2MT 8.2±20% 48 4.40 5.50 4.80 5.50
MWSA0605S-100MT 10±20% 60 4.24 5.30 3.80 4.50
MWSA0605S-150MT 15±20% 90 3.20 4.00 2.60 3.10

MWSA0605S-220MT 22±20% 140 2.80 3.50 2.00 2.60

MWSA0605S-330MT 33±20% 190 2.40 3.00 1.80 2.30

MWSA0605S-470MT 47±20% 230 2.08 2.60 1.50 2.00

MWSA1004S Series
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 12 of 38

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA1004S-R15MT 0.15±20% 0.65 60.00 75.00 40.00 45.00

MWSA1004S-R22MT 0.22±20% 1 48.00 60.00 30.00 35.00

MWSA1004S-R30MT 0.30±20% 1.1 36.00 45.00 30.00 35.00

MWSA1004S-R36MT 0.36±20% 1.2 36.00 45.00 25.00 30.00

MWSA1004S-R47MT 0.47±20% 1.7 32.00 40.00 25.00 30.00

MWSA1004S-R56MT 0.56±20% 1.8 26.40 33.00 20.00 25.00

MWSA1004S-R68MT 0.68±20% 2.4 24.00 30.00 19.00 23.00

MWSA1004S-R80MT 0.80±20% 2.7 23.20 29.00 19.00 23.00

MWSA1004S-1R0MT 1.0±20% 3.3 22.40 28.00 16.00 19.00

MWSA1004S-1R5MT 1.5±20% 4.2 19.20 24.00 14.00 16.00

MWSA1004S-2R2MT 2.2±20% 7 13.20 16.50 10.00 12.00

MWSA1004S-3R3MT 3.3±20% 11.8 12.80 16.00 9.50 11.00

MWSA1004S-4R7MT 4.7±20% 20 10.40 13.00 7.50 9.00

MWSA1004S-6R8MT 6.8±20% 25 9.60 12.00 7.00 8.50

MWSA1004S-8R2MT 8.2±20% 27 7.20 9.00 6.80 8.00

MWSA1004S-100MT 10±20% 30 6.80 8.50 6.90 7.80

MWSA1004S-150MT 15±20% 45 5.60 7.00 5.60 6.50

MWSA1004S-220MT 22±20% 66 4.40 5.50 4.20 5.00

MWSA1004S-330MT 33±20% 92 3.84 4.80 3.80 4.40

MWSA1004S-470MT 47±20% 145 3.10 3.50 2.80 3.30

MWSA1004S-680MT 68±20% 195 2.40 3.00 2.00 2.50

MWSA1204S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms

MWSA1204S-R22MT 0.22±20% 0.9 40.00 50.00 38.00 42.00

MWSA1204S-R47MT 0.47±20% 2.0 38.40 48.00 29.00 33.00

MWSA1204S-R68MT 0.68±20% 3.5 37.60 47.00 24.00 28.00

MWSA1204S-R82MT 0.82±20% 4.5 32.00 40.00 24.00 28.00

MWSA1204S-1R0MT 1.0±20% 7.5 28.00 35.00 20.00 24.00

MWSA1204S-1R5MT 1.5±20% 9.5 24.40 30.50 17.00 20.00

MWSA1204S-2R2MT 2.2±20% 11.5 20.80 26.00 15.00 18.00

MWSA1204S-3R3MT 3.3±20% 13.0 16.80 21.00 13.00 15.00

MWSA1204S-4R7MT 4.7±20% 14.5 14.40 18.00 11.00 13.00

MWSA1204S-6R8MT 6.8±20% 20.0 11.20 14.00 8.00 9.00

MWSA1204S-100MT 10±20% 25.0 8.00 10.00 7.00 8.00

MWSA1204S-150MT 15±20% 39.0 6.00 7.50 5.80 6.50

MWSA1204S-220MT 22±20% 51.0 4.80 6.00 3.80 4.50

MWSA1205S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 13 of 38
Units μH mΩ A A
Symbol L DCR Isat Irms

MWSA1205S-R22MT 0.22±20% 0.7 60.00 75.00 45.00 50.00

MWSA1205S-R36MT 0.36±20% 0.85 40.00 50.00 37.00 42.00

MWSA1205S-R50MT 0.50±20% 1.15 38.40 48.00 33.00 38.00

MWSA1205S-R68MT 0.68±20% 1.55 36.80 46.00 29.00 33.00

MWSA1205S-R82MT 0.82±20% 1.67 31.20 39.00 26.00 30.00

MWSA1205S-1R0MT 1.0±20% 2.2 28.00 35.00 22.00 26.00

MWSA1205S-1R5MT 1.5±20% 3.2 26.40 33.00 19.00 23.00

MWSA1205S-2R2MT 2.2±20% 5.0 19.20 24.00 13.00 15.00

MWSA1205S-3R3MT 3.3±20% 7 17.60 22.00 12.00 14.00

MWSA1205S-4R7MT 4.7±20% 9 16.00 20.00 11.00 13.00

MWSA1205S-6R8MT 6.8±20% 18 12.80 16.00 10.00 12.00

MWSA1205S-100MT 10±20% 22 9.60 12.00 8.00 9.00

MWSA1205S-150MT 15±20% 30 8.00 10.00 7.00 8.00

MWSA1205S-220MT 22±20% 58 5.20 6.50 3.80 4.50

MWSA1205S-330MT 33±20% 84 4.80 6.00 2.80 3.50

MWSA1205S-470MT 47±20% 130 4.00 5.00 2.60 3.00

MWSA1206S Series

Inductance DC Resistance Saturation Current *3 Heat Rating Current*4

Part Number
@100KHZ,1V Max. Max. Typ. Max. Typ.
Units μH mΩ A A
Symbol L DCR Isat Irms
MWSA1206S-4R7MT 4.7±20% 9 19.20 24.00 12.00 15.00

MWSA1206S-5R6MT 5.6±20% 11 18.00 22.50 11.00 13.00

MWSA1206S-6R8MT 6.8±20% 13.5 15.20 19.00 10.00 12.00

MWSA1206S-8R2MT 8.2±20% 16 10.80 13.50 9.00 11.00

MWSA1206S-100MT 10±20% 20.7 11.10 12.50 8.50 10.00

MWSA1206S-120MT 12±20% 23 8.00 10.00 7.80 9.00

MWSA1206S-150MT 15±20% 29 7.20 9.00 7.50 8.50

MWSA1206S-180MT 18±20% 35 6.40 8.00 6.50 7.50

MWSA1206S-220MT 22±20% 39.5 6.00 7.50 6.00 7.00

MWSA1206S-270MT 27±20% 56 5.20 6.50 5.00 6.00

MWSA1206S-330MT 33±20% 75 4.80 6.00 4.80 5.50

MWSA1206S-470MT 47±20% 90 4.40 5.50 4.20 5.00

MWSA1206S-680MT 68±20% 140 3.60 4.50 3.20 4.00

MWSA1206S-101MT 100±20% 200 2.80 3.50 2.50 3.00

MWSA1206S-121MT 120±20% 235 2.56 3.20 1.70 2.00

MWSA1206S-151MT 150±20% 350 2.16 2.70 1.20 1.50

※1: All test data is referenced to 20°C ambient;
※2: Rated current: Isat or Irms, whichever is smaller;
※3: Isat(Typ): DC current at which the inductance drops approximate 30% from its value without current;
※4: Isat(Max): DC current at which the inductance drops approximate 20% from its value without current;
※5: Irms(Typ): DC current that causes the temperature rise (△T =40°C) from 20°C ambient.
※6: Irms(Max): DC current that causes the temperature rise (△T =20°C) from 20°C ambient.
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 14 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 15 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 16 of 38
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 17 of 38

MWSA0402S-220MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 18 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA0518S-R47MT MWSA0518S-R56MT

MWSA0518S-1R5MT

MWSA0518S-2R2MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 19 of 38

MWSA0518S-100MT

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA0503S-R10MT MWSA0503S-R20MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 20 of 38

MWSA0503S-R33MT MWSA0503S-R47MT

MWSA0503S-R68MT MWSA0503S-1R0MT

MWSA0503S-1R2MT MWSA0503S-1R5MT

MWSA0503S-2R2MT MWSA0503S-3R3MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 21 of 38

MWSA0503S-4R7MT MWSA0503S-6R8MT

MWSA0503S-100MT

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA0618S-R10MT MWSA0618S-R22MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 22 of 38

MWSA0618S-R47MT MWSA0618S-R68MT

MWSA0618S-1R0MT MWSA0618S-1R5MT

MWSA0618S-2R2MT MWSA0618S-3R3MT

MWSA0618S-4R7MT MWSA0618S-6R8MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 23 of 38

MWSA0618S-100MT MWSA0618S-220MT

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA0624S-R22MT

MWSA0624S-R47MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 24 of 38

MWSA0624S-1R0MT

MWSA0624S-1R5MT MWSA0624S-2R2MT

MWSA0624S-3R3MT MWSA0624S-4R7MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 25 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 26 of 38

MWSA0603S-1R0MT MWSA0603S-1R5MT

MWSA0603S-4R7MT MWSA0603S-6R8MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 27 of 38

MWSA0603S-150MT

Test Instruments Test Condition

Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA0604S-2R2MT MWSA0604S-4R7MT

MWSA0604S-150MT

Test Instruments Test Condition

Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 28 of 38

MWSA0605S-R47MT MWSA0605S-R68MT

MWSA0605S-1R0MT MWSA0605S-1R5MT

MWSA0605S-2R2MT MWSA0605S-3R3MT

MWSA0605S-4R7MT MWSA0605S-6R8MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 29 of 38

MWSA0605S-8R2MT MWSA0605S-100MT

MWSA0605S-150MT MWSA0605S-220MT

MWSA0605S-330MT MWSA0605S-470MT

Test Instruments Test Condition

Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA1004S-R15MT MWSA1004S-R22MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 30 of 38

MWSA1004S-R30MT MWSA1004S-R36MT

MWSA1004S-R47MT MWSA1004S-R56MT

MWSA1004S-R68MT MWSA1004S-R80MT

MWSA1004S-1R0MT MWSA1004S-1R5MT

MWSA1004S-2R2MT MWSA1004S-3R3MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 31 of 38

MWSA1004S-4R7MT MWSA1004S-6R8MT

MWSA1004S-8R2MT MWSA1004S-100MT

MWSA1004S-150MT MWSA1004S-220MT

MWSA1004S-330MT MWSA1004S-470MT

MWSA1004S-680MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 32 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA1204S-R22MT MWSA1204S-R47MT

MWSA1204S-R82MT
MWSA1204S-R68MT

MWSA1204S-1R0MT MWSA1204S-1R5MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 33 of 38

MWSA1204S-2R2MT MWSA1204S-3R3MT

MWSA1204S-4R7MT MWSA1204S-6R8MT

MWSA1204S-100MT MWSA1204S-150MT

MWSA1204S-220MT
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 34 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 35 of 38
 Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 36 of 38

Performance Graphs
Test Instruments Test Condition
Temperature: 26 ± 3℃
Wayne kerr 3260B/G LCR Meter
Humidity: < 70% RH
Wayne kerr 3265B Bias Current Source
Frequency: 100 KHz, 1.0V
MWSA1206S-4R7MT
MWSA1206S-5R6MT

MWSA1206S-6R8MT MWSA1206S-8R2MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 37 of 38

MWSA1206S-120MT
MWSA1206S-100MT

MWSA1206S-150MT MWSA1206S-180MT

MWSA1206S-220MT MWSA1206S-270MT

MWSA1206S-330MT MWSA1206S-470MT
Sunlord Categories: general confidential Specifications for Wire Wound Molded SMD Power Inductors Page 38 of 38

MWSA1206S-680MT MWSA1206S-101MT

MWSA1206S-121MT MWSA1206S-151MT