P2 V23079 Relay

108-98002
Sept 06 Rev. D
ECOC: JM10
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Index
Dimensions 4
Coil Operating Range 5
Relay Code 6
Coil Data and Ordering Information 7
UL 508 File No. E 111441 Contact Data 9
UL 60950 Insulation 10
General Data 10
IEC/EN60950 IEC Ref. Cert. No. 3271 Packing 12

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

2 pole telecom relay, polarized,

Through Hole Type (THT) or
Surface Mount Technology (SMT),

Relay types: non-latching with 1 coil

latching with 2 coils
latching with 1 coil

ROHS compliant (Directive 2002/95/EC) as per

product date code 0427.

Features
• Standard telecom relay (ringing and test access)
• Slim line 15 x 7.5 mm, 0.590 x 0.295 inch
• Switching current 5 A
• 2 changeover contacts (2 form C / DPDT)
• Bifurcated contacts
• Immersion cleanable
• High sensitivity results in low nominal power
consumption 140 mW for non-latching and latching
with 2 coils 70 mW for latching with 1 coil
• For single coil version:
• Surge voltage resistance between
contact and coil for single coil version:
• 2.5 kV (2 / 10 µs) meets the Telcordia
Requirement GR-1089
• 1.5 kV (10 / 160 µs) meets FCC Part 68

Typical applications Insulation category

• Communications equipment linecard application Basic insulation according IEC / EN 60950
(ringing and test access)
Working voltage ≤ 300 Vrms
PABX
Voice over IP Mains supply voltage ≤ 250 Vrms
• Office equipment Repetitive peak voltage 2500 V
• Measurement and control equipment Pollution degree Internal: 1
• Automotive equipment External: 2
CAN bus, keyless entry, speaker switch Flammability classification V-0
• Medical equipment
Maximum operating temperature 85 °C
• Consumer electronics
Set Top Boxes, HiFi

Options
• 1500 Vrms between open contacts

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Dimensions Dimensions in mm

THT THT SMT long terminals SMT long terminals SMT short terminals SMT short terminals
V23079-x1xxx-B301 V23079-x2xxx-B301 V23079-x1xxx-B301 V23079-x2xxx-B301 V23079-x1xxx-B301 V23079-x2xxx-B301
standard coil overmolded coil standard coil overmolded coil standard coil overmolded coil
mm inch mm inch mm inch mm inch mm inch mm inch
L 14.5 ± 0.10 0.570 ± 0.004 14.6 ± 0.10 0.575 ± 0.004 14.5 ± 0.10 0.570 ± 0.004 14.6 ± 0.10 0.575 ± 0.004 14.5 ± 0.10 0.570 ± 0.004 14.6 ± 0.10 0.575 ± 0.004
W 7.2 ± 0.10 0.283 ± 0.004 7.2 ± 0.10 0.283 ± 0.004 7.2 ± 0.10 0.283 ± 0.004 7.2 ± 0.10 0.283 ± 0.004 7.2 ± 0.10 0.283 ± 0.004 7.2 ± 0.10 0.283 ± 0.004
H 9.8 ± 0.10 0.385 ± 0.004 9.5 ± 0.10 0.374 ± 0.004 10.4 ± 0.15 0.409 ± 0.006 9.9 ± 0.10 0.390 ± 0.004 10.4 ± 0.15 0.409 ± 0.006 9.9 ± 0.10 0.390 ± 0.004
T 3.25 – 0.25 0.128 – 0.010 3.25 – 0.25 0.128 – 0.010 N/A N/A N/A N/A N/A N/A N/A N/A
T1 N/A N/A N/A N/A 5.52 ± 0.15 0.217 ± 0.006 5.52 0.217 ± 0.006 5.52 0.217 ± 0.006 5.52 0.217 ±0.006
T2 N/A N/A N/A N/A 9.4 ± 0.15 0.370 ± 0.006 9.4 ± 0.15 0.370 ± 0.006 7.4 ± 0.15 0.291 ± 0.006 7.4 ± 0.15 0.291 ±0.006
Tw 0.5 ± 0.05 0.020 ± 0.002 0.5 ± 0.05 0.020 ± 0.002 0.5 ± 0.05 0.020 ± 0.002 0.5 ± 0.05 0.020 ± 0.002 0.5 ± 0.05 0.020 ± 0.002 0.5 ± 0.05 0.020 ±0.002
S 0.55 – 0.15 0.022 – 0.006 0.45 0.018 ± 0.002 N/A N/A N/A N/A N/A N/A N/A N/A

THT Version SMT Version

Long terminals Short terminals

P2 SMT S

Mounting hole layout Solder pad layout

View onto the component View onto the component side of the PCB (top view)
side of the PCB (top view) Long terminals Short terminals

0,9 ±0,1

Note: Hole for pin 6 and 7 Note: Solder pad for pin 6 and 7 Note: Solder pad for pin 6 and 7
only for latching with 2 coils. only for latching with 2 coils only for latching with 2 coils
Basic grid 2.54 mm

Terminal assignment
Relay – top view

Non-latching type Latching type, Latching, 2 coils

not energized condition reset condition reset condition
Contacts in reset
position. Both coils can
be used either as set or
reset coils.

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Coil Operating Range

3.4 Unom = Nominal coil voltage
3.2
70 mW
3
Umax. = Upper limit of the operative range of
Umax. at 0 A
2.8
Umax. at 2 x 1 A the coil voltage (limiting voltage) when coils are
2.6
Umax. at 2 x 2 A continously energized
Coil Voltage [U/Unom]

2.4
2.2 Uop. min. = Lower limit of the operative range of
2
1.8
the coil voltage (reliable operate voltage)
1.6 For latching relays Uset min. resp. Ureset min.
1.4
1.2
Urel. min. = Lower limit of the operative range of
1 Unom. nominal coil voltage the coil voltage (reliable release voltage)
0.8
0.6 Uop. min.
0.4
0.2
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140

Ambient Temperature [°C]

2.8
140 mW
2.6
Umax. at 0 A
2.4 Umax. at 2 x 1 A
2.2 Umax. at 2 x 2 A
2
Coil Voltage [U/Unom]

1.8

1.6

1.4

1.2

1 Unom. nominal coil voltage

0.8

0.6
Uop. min.
0.4
Urel. min.
0.2

0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140

Ambient Temperature [°C]

200 mW
2.8

2.6 Umax. at 0 A
2.4 Umax. at 2 x 1 A
2.2
Umax. at 2 x 2 A
2
Coil Voltage [U/Unom]

1.8

1.6

1.4

1.2

1
Unom. nominal coil voltage
0.8

0.6
Uop. min.
0.4 Urel. min.
0.2

0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140

Ambient Temperature [°C]

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Relay Code

V 2 3 0 7 9
Identification of the
Miniature Relay P2

Relay type

THT version SMT version with long terminals

A = non-latching, 1 coil D = non-latching, 1 coil
B = latching, 2 coils E = latching, 2 coils
C = latching, 1 coil F = latching, 1 coil

SMT version with short terminals

G = non-latching, 1 coil
H = latching, 2 coils
J = latching, 1 coil

Coil type
1 = standard coil; B1, E1, F1, J1, H1
2 = overmolded coil, A1*, A2, C1*, D1*, D2, E2, G1*, G2
(only monostable versions, i.e. relay type A, D, G)
*both standard and overmolded coil possible

Coil number
Monostable, 1 coil Latching, 1 coil Latching, 2 coils
008 = 3 V nominal voltage 108 = 3 V nominal voltage 218 = 2.4 V nominal voltage
011= 4.5 V 111 = 4.5 V 208 = 3 V
001 = 5 V 101 = 5 V 211 = 4.5 V
002 = 6 V 102 = 6 V 201 = 5 V
006 = 9 V 106 = 9 V 202 = 6 V
003 = 12 V 103 = 12 V 206 = 9 V
005 = 24 V 105 = 24 V 203 = 12 V
205 = 24 V

Contact arrangement / material

B301 = 2 changeover contacts; silver nickel, gold-plated, against silver nickel, gold-plated
B201 = 2 changeover contacts; silver palladium, gold-plated, against silver palladium

Ordering example: V23079-D2001-B301

Miniature relay P2 SMT version with long terminals (overmolded coil), non-latching, 1 coil, 5 V nominal voltage,
2 changeover contacts, silver nickel contacts

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Coil Data (values at 23 °C) Ordering Information

Nominal Operate/set voltage range Release/ Coil Coil Relay Tyco part
voltage reset voltage power Resistance code number
Unom Minimum
Minimum Maximum
voltage Umin voltage Umax
Vdc Vdc Vdc Vdc mW Ω / ± 10 %

THT Standard non-latching coil

3 2.25 6.50 0.30 140 64 V23079-A1008-B301 2-1393788-2
4 3.00 8.70 0.40 140 114 V23079-A1016-B301 2-1393788-9
4.5 3.38 9.80 0.45 140 145 V23079-A1011-B301 2-1393788-4
5 3.75 10.90 0.50 140 178 V23079-A1001-B301 1393788-3
6 4.50 13.00 0.60 140 257 V23079-A1002-B301 1393788-8
9 6.75 19.60 0.90 140 578 V23079-A1006-B301 2-1393788-0
12 9.00 26.15 1.20 140 1029 V23079-A1003-B301 1-1393788-1
24 18.00 52.30 2.40 140 4114 V23079-A1005-B301 1-1393788-6
THT non-latching, overmolded coil
3 2.25 6.50 0.30 140 64 V23079-A2008-B301 6-1419120-6
4.5 3.38 9.80 0.45 140 145 V23079-A2011-B301 3-1393789-9
5 3.75 10.90 0.50 140 178 V23079-A2001-B301 3-1393789-5
6 4.50 13.00 0.60 140 257 V23079-A2002-B301 3-1393789-6
9 6.75 19.60 0.90 140 578 V23079-A2006-B301 3-1393789-8
12 9.00 26.15 1.20 140 1029 V23079-A2003-B301 3-1393789-7
THT latching 2 standard coils
3 2.25 6.50 2.25 140 64 V23079-B1208-B301 4-1393788-1
4.5 3.38 9.80 3.38 140 145 V23079-B1211-B301 4-1393788-2
5 3.75 10.90 3.75 140 178 V23079-B1201-B301 3-1393788-3
6 4.50 13.00 4.50 140 257 V23079-B1202-B301 3-1393788-5
9 6.75 19.60 6.75 140 578 V23079-B1206-B301 3-1393788-9
12 9.00 26.15 9.00 140 1029 V23079-B1203-B301 3-1393788-6
24 18.00 52.30 18.00 140 4114 V23079-B1205-B301 3-1393788-7
THT latching 2 overmolded coils
2 1.50 4.30 1.50 140 28 V23079-B2219-B301 1-1422002-2
2.4 1.80 5.20 1.80 140 41 V23079-B2218-B301 1-1422002-1
3 2.25 6.50 2.25 140 64 V23079-B2208-B301 1-1422002-0
5 3.75 10.90 3.75 140 178 V23079-B2201-B301 1422002-9
THT latching 1 standard coil
3 2.25 9.20 2.25 70 128 V23079-C1108-B301 5-1393788-3
4.5 3.38 13.85 3.38 70 289 V23079-C1111-B301 5-1393788-4
5 3.75 15.33 3.75 70 357 V23079-C1101-B301 4-1393788-5
6 4.50 18.50 4.50 70 514 V23079-C1102-B301 4-1393788-7
9 6.75 27.75 6.75 70 1157 V23079-C1106-B301 5-1393788-1
12 9.00 37.00 9.00 70 2057 V23079-C1103-B301 4-1393788-8
24 18.00 74.00 18.00 70 8228 V23079-C1105-B301 5-1393788-0
SMT long pins, non-latching, standard coil
3 2.25 6.50 0.30 140 64 V23079-D1008-B301 6-1393788-1
4.5 3.38 9.80 0.45 140 145 V23079-D1008-B301 6-1393788-2
5 3.75 10.90 0.50 140 178 V23079-D1008-B301 5-1393788-5
6 4.50 13.00 0.60 140 257 V23079-D1008-B301 5-1393788-6
9 6.75 19.60 0.90 140 578 V23079-D1008-B301 5-1393788-9
12 9.00 26.15 1.20 140 1029 V23079-D1008-B301 5-1393788-7
24 18.00 52.30 2.40 140 4114 V23079-D1008-B301 5-1393788-8

SMT long pins, non-latching, overmolded coil

3 2.25 6.50 0.30 140 64 V23079-D2008-B301 4-1393789-7
4.5 3.38 9.80 0.45 140 145 V23079-D2011-B301 4-1393789-8
5 3.75 10.90 0.50 140 178 V23079-D2001-B301 4-1393789-3
6 4.50 13.00 0.60 140 257 V23079-D2002-B301 4-1393789-4
9 6.75 19.60 0.90 140 578 V23079-D2006-B301 4-1393789-6
12 9.00 26.15 1.20 140 1029 V23079-D2003-B301 4-1393789-5
Further coil versions are available on request.

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Coil Data (values at 23 °C) Ordering Information

Nominal Operate/set voltage range Release/ Coil Coil Relay Tyco part
voltage reset voltage power Resistance code number
Unom Minimum
Minimum Maximum
voltage Umin voltage Umax
Vdc Vdc Vdc Vdc mW Ω / ± 10 %

SMT long pins, latching, 2 standard coils

2 1.50 4.33 1.50 140 28 V23079-E1219-B301 1-1422007-0
2.4 1.80 5.20 1.80 140 41 V23079-E1218-B301 1422007-5
3 2.25 6.50 2.25 140 64 V23079-E1208-B301 7-1393788-1
4.5 3.38 9.80 3.38 140 145 V23079-E1211-B301 7-1393788-2
5 3.75 10.90 3.75 140 178 V23079-E1201-B301 6-1393788-8
6 4.50 13.00 4.50 140 257 V23079-E1202-B301 1393789-5
9 6.75 19.60 6.75 140 578 V23079-E1206-B301 1393789-9
12 9.00 26.15 9.00 140 1029 V23079-E1203-B301 6-1393788-9
24 18.00 52.30 18.00 140 4114 V23079-E1205-B301 7-1393788-0
SMT long pins, latching, 2 overmolded coil
2 1.50 4.33 1.50 140 28 V23079-E2219-B301 1422007-6
2.4 1.80 5.20 1.80 140 41 V23079-E2218-B301 1422007-9
3 2.25 6.50 2.25 140 64 V23079-E2208-B301 1422007-8
5 3.75 10.90 3.75 140 178 V23079-E2201-B301 1422007-7
SMT long pins, latching, 1 standard coil
3 2.25 9.20 2.25 70 128 V23079-F1108-B301 7-1393788-5
4.5 3.38 13.85 3.38 70 289 V23079-F1111-B301 1-1393788-4
5 3.75 15.33 3.75 70 357 V23079-F1101-B301 7-1393788-3
6 4.50 18.50 4.50 70 514 V23079-F1102-B301 1-1393789-0
9 6.75 27.75 6.75 70 1157 V23079-F1106-B301 1-1393789-2
12 9.00 37.00 9.00 70 2057 V23079-F1103-B301 7-1393788-9
24 18.00 74.00 18.00 70 8228 V23079-F1105-B301 1-1393789-1
SMT short pins, non-latching, standard coil
3 2.25 6.50 0.30 140 64 V23079-G1008-B301 8-1393788-0
4.5 3.38 9.80 0.45 140 145 V23079-G1011-B301 1-1393789-7
5 3.75 10.90 0.50 140 178 V23079-G1001-B301 7-1393788-6
6 4.50 13.00 0.60 140 257 V23079-G1002-B301 1-1393789-5
9 6.75 19.60 0.90 140 578 V23079-G1006-B301 1-1393789-6
12 9.00 26.15 1.20 140 1029 V23079-G1003-B301 7-1393788-7
24 18.00 52.30 2.40 140 4114 V23079-G1005-B301 7-1393788-8
SMT short pins, non-latching, overmolded coil
3 2.25 6.50 0.30 140 64 V23079-G208-B301 5-1393789-4
4.5 3.00 8.70 0.40 140 114 V23079-G2016-B301 1393790-5
5 3.38 9.80 0.45 140 145 V23079-G2011-B301 5-1393789-5
6 3.75 10.90 0.50 140 178 V23079-G2001-B301 4-1393789-9
9 4.50 13.00 0.60 140 257 V23079-G2002-B301 5-1393789-0
12 6.75 19.60 0.90 140 578 V23079-G2006-B301 5-1393789-3
24 9.00 26.15 1.20 140 1029 V23079-G2003-B301 5-1393789-1
SMT long pins, latching, 2 standard coils
3 2.25 6.50 2.25 140 64 V23079-H1208-B301 2-1393789-4
4.5 3.38 9.80 3.38 140 145 V23079-H1211-B301 8-1393788-4
5 3.75 10.90 3.75 140 178 V23079-H1201-B301 2-1393789-0
6 4.50 13.00 4.50 140 257 V23079-H1202-B301 2-1393789-1
9 6.75 19.60 6.75 140 578 V23079-H1206-B301 2-1393789-3
12 9.00 26.15 9.00 140 1029 V23079-H1203-B301 8-1393788-3
24 18.00 52.30 18.00 140 4114 V23079-H1205-B301 2-1393789-2
SMT long pins, latching, 1 standard coils
3 2.25 9.20 2.25 70 128 V23079-J1108-B301 2-1393789-9
4.5 3.38 13.85 3.38 70 289 V23079-J1111-B301 3-1393789-0
5 3.75 15.33 3.75 70 357 V23079-J1101-B301 2-1393789-5
6 4.50 18.50 4.50 70 514 V23079-J1102-B301 2-1393789-6
12 9.00 37.00 9.00 70 2057 V23079-J1103-B301 2-1393788-7
24 18.00 74.00 18.00 70 8228 V23079-J1105-B301 2-1393789-8
SMT short pins, non-latching, 1 overmolded coil high dielectric
3 2.25 6.10 0.30 200 45 V23079-G2008-X079 1422006-5
5 3.75 10.10 0.50 200 125 V23079-G2001-X071 1422006-1
6 4.50 12.10 0.60 200 180 V23079-G2002-X072 1422006-2
9 6.75 18.20 0.90 200 405 V23079-G2006-X073 1422006-3
12 9.00 24.20 1.20 200 720 V23079-G2003-X074 1422006-4
Further coil versions are available on request.

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Contact Data

Number of contacts and type 2 changeover contacts

Contact assembly Bifurcated contacts
Contact material Silver nickel, gold-covered
Limiting continuous current at max. ambient temperature 2A
Maximum switching current 5A
Maximum swichting voltage 220 Vdc
250 Vac
Maximum switching capacity 60 W, 62.5 VA
Thermoelectric potential < 10 µV
Minimum switching voltage 100 µV
Initial contact resistance / measuring condition: 10 mA / 20 mV < 50 mΩ
Electrical endurance at 12 V / 10 mA typ. 5 x 107 operations
at 6 V / 100 mA typ. 1 x 107 operations
at 60 V / 500 mA typ. 5 x 105 operations
at 30 V / 1000 mA typ. 1 x 106 operations
at 30 V / 2000 mA typ. 2 x 105 operations
Mechanical endurance typ. 108 operations
UL contact ratings 220 Vdc / 0.24 A - 60 W
125 Vdc / 0.24 A - 30 W
250 Vac / 0.25 A - 62.5 VA
125 Vac / 0.5 A - 62.5 VA
30 Vdc / 2 A - 60 W

Max. DC Load Breaking Capacity

resistive load
DC Voltage [Vdc]

DC current [A]

All specifications subject to change. Consult Tyco Electronics for latest specifications.  of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Insulation
Standard Version High dielectric Version
Insulation resistance at 500 Vdc > 10 Ω9
> 109 Ω
Dielectric test voltage (1 min)
between coil and contacts (Relay with 1 coil) 1500 Vrms 1500 Vrms
between adjacent contact sets 1000 Vrms 1500 Vrms
between open contacts 1000 Vrms 1500 Vrms
Surge voltage resistance
according to Telcordia TR-NWT-001089 (2 /10 µs)
between coil and contacts (Relay with 1 coil) 2500 V 2500 V
between adjacent contact sets 2500 V 2500 V
between open contacts 2000 V 2500 V
according to FCC 68 (10/160 µs)
between coil and contacts (Relay with 1 coil) 1500 V
between adjacent contact sets 1500 V
between open contacts 1500 V
Insulation according to IEC / EN 60950 Basic insulation
Clearance 1.3 mm
Creepage distance 2.5 mm

High Frequency Data

Capacitance
between coil and contacts max. 2 pF
between adjacent contact sets max. 1.5 pF
between open contacts max. 1 pF
RF Characteristics
Isolation at 100 MHz / 900 MHz - 39.0 dB / - 20.7 dB
Insertion loss at 100 MHz / 900 MHz - 0.02 dB / - 0.27 dB
V.S.W.R. at 100 MHz / 900 MHz 1.04 / 1.40

General Data
Operate time at Unom typ. / max. 3 ms / 4 ms

Reset time (latching) at Unom , typ. / max. 3 ms / 4 ms

Release time without diode in parallel (non-latching), typ. / max. 2 ms / 4 ms
Release time with diode in parallel (non-latching), typ. / max. 4 ms / 6 ms
Bounce time at closing contact, typ. / max. 1 ms / 3 ms
Maximum switching rate without load 50 operations/s
Ambient temperature -40 °C ... +85 °C
Thermal resistance < 125 K/W
Maximum permissible coil temperature 125 °C
Vibration resistance (function) 35 G
10 to 1000 Hz
Shock resistance, half sinus, 11 ms 50 G (function)
150 G (damage)
Degree of protection / Environmental protection immersion cleanable, IP 67 / RT III
Needle flame test application time 20 s, no burning < 15s
Mounting position any
Processing information Ultrasonic cleaning is not recommended
Weight (mass) max. 2.8 g
Terminal surface SnCu 0.7
Moisture sensitive level (JEDEC J-STD-020B) - SMD types MSL 3
Resistance to soldering heat 265 °C / 10 s

All data refers to 23 °C unless otherwise specified.

All specifications subject to change. Consult Tyco Electronics for latest specifications. 10 of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Recommended Soldering Conditions

Soldering conditions according IEC 60058-2-58 and
IPC/JEDEC J-STD-020B

20 - 40 sec Full line: typical

Dotted line: process limits
240 °C

180 °C
Temperature °C

130 °C forced
cooling
100 °C

Vapor Phase Soldering: Temperature/Time Profile

Time (s)
(Lead and Housing Peak Temperature)

Recommended reflow soldering profile

Temperature °C

Time (s)
Infrared Soldering: Temperature/Time Profile
(Lead and Housing Peak Temperature)

Resistance to soldering heat - Reflow profile

Temperature °C

Time (s) Infrared Soldering: Temperature/Time Profile

(Lead and Housing Peak Temperature)

All specifications subject to change. Consult Tyco Electronics for latest specifications. 11 of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

Packing Dimensions in mm

Tube for THT version

50 relays per tube
2‘000 relays per box

Tape and reel for SMT

version
with long terminals
400 relays per reel
2‘000 relays per box

Tape and reel for SMT

version with short
terminals
500 relays per reel
2‘500 relays per box

Reel dimension

All specifications subject to change. Consult Tyco Electronics for latest specifications. 12 of 14
 AXICOM
Telecom-, Signal and RF Relays 108-98002 Rev. D

P2 V23079 Relay

IM Relays D2n Relays

4th generation slim line – low profile polarized 2 c/o telecom relay with 2nd generation non polarized 2 c/o relay for telecom and various
bifurcated contacts, available as non latching or latching relay with 1 other applications. Nominal voltage range from 3 ... 48 V, coil pow-
coil. Nominal voltage range from 1.5 ... 24 V, coil power consumption of er consumption from 150 .... 500 mW. The D2n relay is capable to
50 ... 200 mW, latching relays with 1 coil 100 mW. The IM relay is availa- switch currents up to 3 A. Dielectric strength fulfills the requirements
ble as through hole and surface mount type (J-Legs and Gull Wings) according FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 20
and capable to switch loads up to 60 W/62,5 VA. It is currently the only x10 mm board space and 11 mm height.
2 A rated 4G relay on the market. Dielectric strength fulfills the Telcordia
requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68
(1,5 kV – 10 / 160 µs). The IM relay is tested according CECC/IECQ and
P1 Relays
certified in accordance with IEC/EN 60950 and UL 60950. Dimensions Extremely sensitive, polarized 1 c/o relay with bifurcated contacts for a
approx. 10 x 6 mm board space and 5.65 mm height. wide range of applications, available as non latching or latching relay
with 1 or 2 coils. Nominal voltage range from 3 ... 24 V, coil power
consumption 65 mW, latching relays with 1 coil 30 mW. The P1 relay
P2 Relays is available as through hole or surface mount type and capable to
3rd generation polarized 2 c/o telecom relay with bifurcated contacts, switch currents up to 1 A. Dielectric strength fulfills the requirements
available as non latching or latching relay with 1 or 2 coils. Nominal according FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 13
voltage range from 3 ... 24 V, coil power consumption 140 mW, lat- x 7,6 mm board space and 7 mm height for THT or 8 mm height for
ching relays with 1 coil 70 mW. The P2 Relay is available as through SMT version.
hole or surface mount type and capable to switch currents up to 5 A.
Dielectric strength fulfills the Telcordia requirements according GR W11 Relays
1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The P2
relay is tested according CECC/IECQ and certified in accordance with Low cost, non polarized 1 c/o relay for various applications. Nominal
IEC/EN 60950 and UL 60950. Dimensions approx. 15 x 7,5 mm board voltage range from 3 ... 24 V, coil power consumption 450 mW, sen-
space and 10 mm height. sitive versions 200 mW. The W11 relay is capable to switch currents
up to 3 A. Dielectric strength 1000 Vrms. Dimensions approx. 15,6 x
10,6 mm board space and 11,5 mm height.
FX2 Relays
3rd generation polarized 2 c/o telecom relay with bifurcated contacts, Reed Relays
available as non latching or latching relay with 1 coil. Nominal voltage
High sensitive, non polarized relay for telecom and various other
range from 3 ... 48 V, coil power consumption of 80 ... 260 mW for
applications, available with 1 n/o, 2 n/o or 1c/o contacts. Nominal
the high sensitive version, 140... 300 mW for the standard version,
voltage range from 5 ... 24 V, coil power consumption 50...280 mW
latching relays with 1 coil 100 mW. The FX2 relay is available as
for 1 n/o and 125 ... 280 mW for 2 n/o or 1 c/o versions. Reedrelays are
through hole type and capable to switch loads up to 60 W/62,5 VA.
available in DIP or SIL housing and capable to switch currents up to
Dielectric strength fulfills the Telcordia requirements according GR
0,5 A. Integrated diode and/or electrostatic shield optional. Dielectric
1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The
strength 1500 Vdc. Dimensions approx. 19,3 x 7 mm board space and
FX2 relay is tested according CECC/IECQ and certified in accordance
5 ... 7,5 mm height for DIP or 19,8 x 5 mm board space and 7,8 mm
with IEC/EN 60950 and UL 60950. Dimensions approx. 15 x 7,5 mm
height for SIL version.
board space and 10,7 mm height.

Cradle Relays
FT2 / FU2 Relays
Extremely reliable and mature relay family of 1st generation for
3rd generation non polarized, non latching 2 c/o telecom relay with various signal switching applications. Available as non polarized,
bifurcated contacts. Nominal voltage range from 3 ... 48 V, coil power polarized / latching and relay with AC coil. The benefit is the possibility
consumption 200 ... 300 mW. Most sensitive 48 V relay. Available as of combining various contact sets from 1 up to 6 poles, single and bi-
through hole and surface mount type. Dielectric strength fulfills the furcated contacts, different contact materials with a coil voltage range
Telcordia requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC from 1,5 Vdc to 220 Vac. Cradle relays are available as dust protected
part 68 (1,5 kV – 10 / 160 µs). The FT2/FU2 relay is tested according and hermetically sealed versions, with plug in or solder terminals
CECC/IECQ and certified in accordance with IEC/EN 60950 and UL 60950. and are capable to switch currents up to 5 A. Forcibly guided (linked)
Dimensions approx. 15 x 7,5 mm board space and 10 mm height. contact sets optional. Dielectric strength 500 Vrms. Dimensions from
approx. 19 x 24 to 19x35 mm board space and 30 mm height.
FP2 Relays
3rd generation polarized 2 c/o telecom relay with bifurcated contacts, Other Relays
available as non latching or latching relay with 1 or 2 coils. Nominal
We offer a variety of different relay families for maintenance and
voltage range from 3 ... 48 V, coil power consumption of 80 ... 260
replacement purposes. These relays are up to 60 years old now, such
mW for the high sensitive version, 140... 300 mW for the standard
as Card Relay SN (V23030 / V23031 series), Small General Purpose
version, latching relays with 1 coil 100 mW.. The FP2 Relay is available
Relay (V23006 series), Small Polarized Relay (V23063 ... V23067 and
as through hole type and capable to switch loads up to 60 W/62,5 VA.
V23163 ... V23167 series). Accessories like sockets, hold down springs,
Dielectric strength fulfills FCC part 68 (1,5 kV – 10 / 160 µs). The FP2
etc. optional.
is tested according CECC/IECQ approved. Dimensions approx. 14 x
9 mm board space and 5 mm height.
HF3 Relay
MT2 High performance low cost RF relay with excellent RF characteristics.
Available with an impedance of 50 and 75 Ohm. Suitable for frequen-
2nd generation non polarized, non latching 2 c/o telecom and si-
cies up to 3 GHz. Actually smallest RF relay available combining small
gnal relay with bifurcated contacts. Nominal voltage range from
size, excellent RF performance and SMD solderability. Available as non
3 ... 48 V, coil power consumption 150/200/300/400 and 550 mW.
latching or latching relay with 1 or 2 coils and a nominal coil voltage
Dielectric strength fulfills the requirements according FCC part 68
range from 3 ... 24 V, coil power consumption 140 mW, latching relays
(1,5 kV – 10 / 160 µs).
with 1 coil 70 mW. Dimensions 14.6 x 7.3 x 10 mm.
Dimensions approx. 20 x 10 mm board space and 11 mm height.

All specifications subject to change. Consult Tyco Electronics for latest specifications. 13 of 14
Tyco Electronics Logistics AG
Werk Axicom Au
Seestrasse 295
CH-8804 Au-Wädenswil / Switzerland
Phone +41 44 782 91 11
Fax +41 44 782 90 00
E-mail: [email protected]

Tyco Electronics
Paulsternstrasse 26
D-13629 Berlin / Germany
Phone +49 30 386 38573
Fax +49 30 386 38575
E-mail: [email protected]

Tyco Electronics EC Trutnov s.r.o.

Komenského 821
CZ-541 01 Trutnov / Czech Republic
E-mail: [email protected]

Tyco Electronics Corporation

POB 3608,
Harrisburg, PA 17105, USA
Phone +1 800-522-6752