Aegis® Shaft Grounding Ring Bearing Protection Handbook: Edition 2

® SGR
BEARING PROTECTION RING

Edition 2
$19.95
AEGIS® SHAFT GROUNDING RING

BEARING PROTECTION HANDBOOK
Best Practices for New Motor Design, Motor Repair and Engineering
Specifications, Shaft Voltage Testing, and Bearing Inspections
COMPANY INFORMATION
Electro Static Technology, An ITW Company, is a global manufacturer and inventor of AEGIS® Bearing Protection
Rings used in electric motors and other rotating equipment to safely discharge variable frequency drive (VFD)
voltages to ground. AEGIS® Shaft Grounding Ring technology is installed in all ranges of motors from fractional
horse power to large medium voltage motors used in virtually all commercial and industrial applications.
AEGIS® Shaft Grounding Ring technology is the only technology that combines both contact and non-contact
nanogap technology to reliably protect bearings from electrical discharges that cause pitting, frosting and fluting
damage. AEGIS® Ring Technology uses proprietary conductive micro fibers arranged circumferentially around the
motor shaft and secured in our patented AEGIS® FiberLock™ channel which protects them during operation. The
following patents apply: 8199453, 8169766, 7193836, 7136271, 7528513, 7339777, and other patents pending.
WARRANTY
Units are guaranteed for one year from date of purchase against defective materials and workmanship. Replacement
will be made except for defects caused by abnormal use or mishandling. All statements and technical information
contained herein, or presented by the manufacturer or their representative are rendered in good faith. User must
assume responsibility to determine suitability of the product for intended use. The manufacturer shall not be
liable for any injury, loss or damage, direct or consequential arising out of the use, or attempt to use the product.
SAFETY
Follow all workplace safety policies and procedures applicable to electric motor repair and for all hazardous
operations. Wear all applicable personal protective equipment (PPE) required by the applicable law. Employees
should be informed of the relevant safety rules and employers should enforce compliance. The manufacturer
shall not be liable for any injury, loss or damage, direct or consequential arising out of the use, or attempt to use
the product or procedures described in this manual.
© 2013 Electro Static Technology, An ITW Company, All rights reserved.
No part of this book may be reproduced without permission in writing from Electro Static Technology, except by a reviewer
who may quote brief passages or reproduce illustrations in a review with appropriate credit; nor may any part of this book be
reproduced, stored in a retrieval system, or transmitted in any form or by any means-electronic, photocopying, recording, or
other-without permission in writing from Electro Static Technology.
This book is generally reviewed every year and updated. Comments and suggestions are invited. Any errors or omissions in
the data should be brought to the attention of the Editor. Additions and corrections to the Handbook in print will be in the
Handbook published the following printed edition and, as soon as verified, on the Electro Static Technology Internet Web site.
Disclaimer-Application notes are intended as general guidance to assist with proper application of AEGIS® Bearing Protection Ring to
protect motor bearings. All statements and technical information contained in the application notes are rendered in good faith. User
must assume responsibility to determine suitability of the product for its intended use.
ISBN 978-0-9891315-3-7
TABLE OF CONTENTS
Introduction-New Motor and Repair Standards for Inverters 4
New Motor and Repair Standards 5
About VFD Induced Shaft Voltages & Bearing Currents 6-9
Bearing Frosting & Fluting 10
Cutting and Inspecting a Bearing 11-12
AEGIS® Shaft Grounding Best Practices 13-21

AEGIS® Technology 22-24

Testing for Shaft Voltage 25-30

Probe Tip Installation & ScopeMeter Set Up 31-35

Selecting the Correct Size Ring 36

AEGIS® Bearing Protection Ring Parts List 37-45

Engineering Specification 46

Conversion Table - Inches - Metric 47
TO RECEIVE HANDBOOK UPDATES:

This handbook will be periodically updated. To automatically receive
updates, please subscribe at:
www.est-aegis.com/bearing
Use of the EASA logo expresses membership only and not endorsement by EASA of the content in this handbook.
© 2013 Electro Static Technology www.est-aegis.com AEGIS® Handbook | 3

Patented Technology
Introduction-New Motor and Repair Standards for Inverters
ANSI/EASA Standard AR100-2010, Section 2, Mechanical Repair: 2.2 Bearings

“Bearings should be inspected for fretting,
fluting, frosting, scoring or other damage.”
Electrical Motor Repair, Bearing Inspection, and Testing Services:

Electrical motor repair, bearing inspection, and testing services are focused on providing a total package
of solutions for industrial and commercial customers. Especially important are services that relate to
motors operated by variable frequency drive (VFD) inverters. Best practices in motor repair and analysis
techniques will drive improved service offerings which improve the service to end users.
Best Practices and Service Portfolio:
A ssess motors with shaft voltage testing when operated on variable frequency drives
E nsure that best practices are followed for bearing protection during the repair
G ive advice on preventing bearing failures for VFD driven motors
Inspect bearings for signs of electrical discharge machining (EDM) damage
S atisfy the customer with superior repair services
Customers demand repair, testing and analysis services to ensure uptime and reliability and often
recognize the leading service providers with their business. Therefore, the value added service offerings
explained in this manual will help the motor repair and service company meet customer requirements
by offering best practices in motor repair for VFD driven equipment.
EDM Pit Frosted Bearing Race Fluted Outer Bearing Race
4 | AEGIS® Handbook www.est-aegis.com © 2013 Electro Static Technology

Patented Technology
New Motor and Repair Standards
Be the leader in your industry!

Best Practices: The best practices in this handbook are intended to assist the motor service repair and manufacturing
industry in protecting motors operated by variable frequency drives (VFD) and establish bearing protection standards for
new motor desings.
• Adding AEGIS® Ring Technology to any new motor or motor repair for VFD driven motors is the best practice for motor
shaft grounding in order to protect bearings from shaft voltages and bearing currents.
• In addition to AEGIS® rings, motors above 100 HP (75kW) should have the opposite bearing isolated to prevent high
frequency circulating currents.
• When the recommendations are followed as part of the best repair practices, customers may be assured that their
motors are repaired to the highest standards of service and reliability.
ANSI/EASA Standard AR100-2010 and Shaft Grounding Best practices: Going

the extra mile will earn loyalty and repeat business. Motor manufacturers and service shops that solve their customer’s
problems and keep their motors operating in peak condition will be sought out and their recommendations followed.
• Operations and facilities engineers and managers count on the motor service and repair shop to keep abreast of the
latest technology and best practices.
• AEGIS® Shaft Grounding Ring technology, proven in over a million installations worldwide, is an innovative and “one-
of-a-kind” technology designed specifically for VFD induced bearing currents. The concept won first prize in 2007 from
the IEEE in a paper titled “Design Aspects of Conductive Microfiber Rings for Shaft Grounding Purposes”.
Bearing Inspection Report: Cutting and inspecting every bearing in motors that come in for repair,
especially when the motor is operated on a variable frequency drive, will often provide vital information needed to make
the best repair recommendations. Detection of electrical discharge machining pits or fluting in the bearings often requires
repair services referred to in this manual.
• Installing a Shaft Grounding Ring (AEGIS® SGR or iPRO) on any motor operated on variable frequency drives (VFD)
• Machining for an internal or external mounting of AEGIS® rings
• Isolating a motor bearing with an insulated sleeve; coating bearing housing with insulating material; adding a hybrid
ceramic ball bearing or ceramic coated bearing to the repair for motors over 100 HP (75kW).
Provide Testing and Analysis Services: Offering the latest testing and analysis services for motors
operated on variable frequency drives (VFD) improves system reliability and uptime. Services include vibration analysis,
thermography, and now shaft voltage testing services.
• New - Shaft Voltage Testing: Using a portable oscilloscope like the Fluke 190 series together with the AEGIS® Shaft
Voltage Probe kit allows a trained technician to easily measure shaft voltage on any VFD driven motor and detect if
there is a potential for bearing discharges.
• Best accomplished:
At the plant or facility while the motor is operating
At initial startup to detect shaft voltages and prevent possible future problems
After the motor is repaired with AEGIS® Shaft Grounding Rings to verify their effectiveness
Periodically as part of a preventative maintenance program
• Adding shaft voltage testing services to current vibration analysis, thermography or other testing compliments the
testing portfolio with an important value added service for customers.

Patented Technology
About VFD Induced Shaft Voltages and Bearing Currents
Electric Motors Operating on Line Voltage

Balanced voltage condition
460 VAC
50/60Hz
• Electric induction motors are designed for operation on 3 phase sine wave
power - either 50 or 60 Hz.
• The input power is balanced in frequency, phase (120 degree phase shift) and in
amplitude.
• Common mode voltage - the sum of the 3 phases always equal zero volts when
properly balanced.
Note: Bearing protection generally not needed except for large frame motors.
Electric Motors Operated by Variable Frequency Drives (VFD)

Unbalanced voltage condition
• When operated by VFD, the power to the motor is a series of positive and
negative pulses instead of a smooth sine wave.
• The input voltage is never balanced because the voltage is either 0 volts, positive,
or negative with rapid switching between pulses in all three phases.
• The common mode voltage is usually a “square wave” or “6 step” voltage wave
form.
Bearing protection needed to mitigate electrical discharge machining

(EDM) damage in bearings.

Patented Technology
There are two primary sources of bearing currents in VFD driven

AC motors (Bearing Currents A and B):
Bearing Current A: is a capacitive induced shaft voltage that

Total Qualitative Bearing Currents
discharges in the motor bearings. The VFD induced shaft
voltages are capacitively coupled from stator to rotor through
parasitic capacitance and create the possibility of bearing
currents. Region 1 Region 2
Motors up to Motors over 100 HP/75kW
100 HP/75kW
Bearing Currents
a. Virtually any motor from fractional HP to large
motors may have bearing currents from this source.
a. Voltages can discharge through the motor bearings
resulting in EDM pitting and fluting failure.
Best Practice: Ground the motor shaft with the AEGIS®

Shaft Grounding Ring to provide a path of least 1 100 200 300
resistance to ground and divert current away from the Motor Horse Power
motor’s bearings.
Ref: NEMA MG1 Part 31.4.4.3
An Electric Motor works like a Capacitor

(Bearing Current A)
Common Mode
Supply 480vAC
• The pulses to the motor from the VFD create a
capacitively coupled common mode voltage on the
motor shaft. Portion of charge returned through ground wires
• Voltages are measurable with a Fluke 190 series

portable oscilloscope and AEGIS® SVP Shaft Voltage
Portion of charge returned through ground wires

Stator
Probe Tip. Rotor
Shaft Load
• Creates electrical bearing discharge currents. Rotor
Stator
Unbalanced
output
VFD Balanced
3-phase input
Stator
tato
Rotor
Roto
© 2013 Electro Static Technology
Shaft www.est-aegis.com
Patented Technology
AEGIS® Handbook | 7
Voltage arcs through the bearing
• Voltages arc through the bearings, and electrical Common Mode Shaft Voltage Arc
Supply 480 v pk-pk 30 v pk-pk
discharge machining (EDM) creates thousands of pits
• Bearings degrade, resulting in increased friction and

Portion of charge returned through ground wires
noise
Stator
• Eventually, the rolling elements can cause fluting Rotor
damage to the bearing races Shaft Load
Rotor
• Bearing lubrication/grease deteriorates, is burnt and Stator
fails Unbalanced
output
• Potential for costly unplanned downtime VFD Balanced

3-phase input
EDM Pits
Burnt Grease
High Frequency Circulating Currents
Bearing Current B: High frequency circulating currents may

flow due to a high-frequency flux produced by common-mode
currents. High frequency inductive circulating currents from
VFDs are in the KHz or MHz frequencies.
Region 1 Region 2
a. May be present in motors above 100 HP. 100 HP/75kW
Bearing Currents
a. Circulate through the motor bearings, shaft to frame.
Best Practice: Interrupting the high frequency circulating

current in the bearing is the best approach to mitigating
potential bearing damage. Also, motors subject to
Current B (high frequency circulating currents) will also
be subject to Current A (capacitively induced shaft 1 100 200 300
voltage) and therefore need an AEGIS® Shaft Grounding Motor Horse Power
Ring.

Patented Technology
A third source of bearing currents are circulating currents from

60Hz/50Hz Line Voltage (motors over 500 Frame):

Bearing Current C: Sinusoidal voltage sources can cause
circulating currents in large machines due to the motor’s
asymmetrical design. 50/60Hz operation can result in circulating
currents due to motor magnetic asymmetries. Region 1 Region 2
100 HP/75kW
Bearing Currents
a. Usually present in very large machines only.
a. Circulate through the motor bearings, shaft to frame.
Best Practice: Interrupting the circulating current is the best

approach to mitigating potential bearing damage.
Ref: NEMA MG1 Part 31.4.4.3
1 100 200 300
Motor Horse Power
AC Induction Motors
NO VFD-
VFD OPERATION 50/60 Hz line operation
Motors up to and Motors over 100hp Motors over 500hp
including 100hp to 500hp (Medium Voltage-greater than Motors over 500 Frame
(Low Voltage) (Low Voltage-up to 600 volts AC) 600 volts AC) (Medium Voltage)
Bearing Current A Bearing Current A & B Bearing Current A, B & C Bearing Current C
AEGIS® iPRO
AEGIS® SGR AEGIS® SGR AEGIS® iPRO
(may not be needed)
Install AEGIS® SGR Install AEGIS® SGR opposite Install AEGIS® iPRO opposite Install AEGIS® iPRO opposite
on DE or NDE side of bearing insulation; side of bearing insulation; side of bearing insulation;
usually DE usually DE usually DE
n/a Isolate one bearing, usually Isolate one bearing, usually the Isolate one bearing, usually
the NDE to break the NDE to break the circulating the NDE to break the
circulating current path current path circulating current path

Patented Technology
Bearing Frosting & Fluting
EDM Electrical Discharge Machining
Because of the high-speed switching frequencies in PWM inverters, variable

frequency drives induce shaft currents in AC motors. The switching frequencies
of insulated-gate bipolar transistors (IGBT) used in these drives produce
voltages on the motor shaft during normal operation through parasitic
capacitance between the stator and rotor. These voltages, which can register
10-40 volts peak, are easily measured by touching an oscilloscope probe to
the shaft while the motor is running.
Reference: NEMA MG1 Section 31.4.4.3
Once these voltages reach a level sufficient to overcome the dielectric

EDM Pit properties of the bearing grease, they discharge along the path of least
resistance — typically the motor bearings — to the motor housing. During
virtually every VFD switching cycle, induced shaft voltage discharges from the
motor shaft to the frame via the bearings, leaving a small fusion crater (fret) in
the bearing race. When this event happens, temperatures are hot enough to
melt bearing steel and severely damage the bearing lubrication.
These discharges are so frequent (millions per hour) that before long the entire
Frosted Bearing Race bearing race becomes marked with countless pits known as frosting. A
phenomenon known as fluting may occur as well, producing washboard-like
ridges across the frosted bearing race. Fluting causes excessive noise and
vibration and in heating, ventilation, and air-conditioning systems, it is
magnified and transmitted by the ducting. Regardless of the type of bearing
or race damage that occurs, the resulting motor failure often costs many
thousands or even tens of thousands of dollars in downtime and lost
production.
Failure rates vary widely depending on many factors, but evidence suggests
Fluted Outer Bearing Race that a significant portion of failures occur only 3 to 12 months after system
startup. Because many of today’s AC motors have sealed bearings to keep out
dirt and other contaminants, electrical damage has become the most common
cause of bearing failure in AC motors with VFDs.

Patented Technology
Cutting and Inspecting a Bearing
Bearing Inspection
Cutting and inspecting every bearing in motors that come in for

repair, especially motors operated on variable frequency drives,
will often provide vital information to make the best repair
recommendation and improve performance.
Report template available at: www.est-aegis.com/bearing
1. Inspect the bearing and bearing cavity and retain a sample of the
lubricant if further analysis is warranted. Look for:
a. Contamination
b. Signs of excessive heat
c. Hardening of grease
d. Abnormal coloration (blackened grease)
e. Excess grease escaping the bearing
2. Cut the outer race into halves.

Follow established safety precautions and use personal protective
equipment including eye protection, hearing protection, face
shield, gloves and protective clothing.
3. Inspect the grease and contamination in the bearing.

a. Burnt Grease: Continuous electrical arcing in the motor bearings will
often rapidly deteriorate the lubricating capability of the grease and
cause bearing race damage. When an arc occurs, the oil component
of the grease is heated beyond its temperature capacity.
b. Contamination: In addition to the burnt grease, the arcing causes
small metal particles to loosen from the bearing races/balls which are
distributed in the grease. These particles are abrasive and intensify
the bearing wear.

Patented Technology
Cutting and Inspecting a Bearing
Burnt bearing grease is blackened and often times contaminated

with metal particles.
New bearing grease is available in many colors.
4. Clean the bearing’s components using a degreaser or solvent.

Follow all safety precautions.
5. Inspect for evidence of Electrical Discharge Machining (EDM): EDM

are millions of microscopic electrical pits created when current discharges
through the motor’s bearings. The electrical voltage overcomes the
dielectric of the bearing lubrication and instantaneously arcs through the
inner race, through the ball and to the outer race. The individual pit is
usually between 5 and 10 micron diameter.
6. Frosting: This will appear to be a grey discolored line around all or part of
the bearing race and may be evident in the inner and outer race. The
discoloration may be caused by wear or by electrical EDM. Examination
under a microscope may be required to determine if the line is EDM or
not. If the motor was operated on a VFD with no bearing protection there
is a high likelihood that the frosting is from EDM.
1000x
7. Fluting Damage: Identified by a distinctive washboard pattern. Fluting

can be identified with the naked eye or with 10x magnification. Fluting is
sometimes confused with mechanical bearing damage so care should be
taken to correctly assign electrical fluting damage to the pattern observed.
In addtion to using this manual please refer to other bearing failure

analysis experts in order to determine the root cause of failure.

Patented Technology
AEGIS® Shaft Grounding Best Practices
Grounding
The AEGIS® Ring conducts harmful shaft voltages away from the bearings to
ground. Voltage travels from the shaft , through the conductive microfibers,
through the housing of the ring, through the hardware (or conductive epoxy)
used to attach the ring to the motor, to ground. All paths must be conductive.
Note: Overspray on end

bracket must be removed to
ensure a conductive path to
ground. Clean all fits.
Photo courtesy of Independent Electric Path to Ground
Shaft Preparation for Internal and External Installation
STOP AEGIS® Rings should not operate over a keyway because the edges are very
sharp. For proper performance:
Adjust or change spacer and screw lengths to avoid the keyway; or
Fill the keyway (in the area where the AEGIS® microfibers will be in
contact with the shaft) with a fast-curing epoxy putty such as Devcon®
Plastic Steel® 5 Minute® Putty(SF).
Motor shaft must be conductive:

Right Wrong
Shaft must be clean and free of any coatings, paint, or other
nonconductive material (clean to bare metal). Depending on the
condition of the shaft, it may require using emery cloth or Scotch-Brite™.
If the shaft is visibly clean, a non petroleum based solvent may be used
to remove any residue. If possible, check the conductivity of the shaft
using an ohm meter.
Ohms test:
Place the positive and negative meter leads on the shaft at a place where
the microfibers will contact the shaft. Each motor will have a different
reading but in general you should have a maximum reading of less than
2 ohms. If the reading is higher, clean the shaft again and retest.

Patented Technology
Shaft Preparation continued

Colloidal Silver Shaft Coating (CS015) is recommended for all applications.
The silver coating enhances the conductivity of the shaft and also lessens
the amount of corrosion that can impede the grounding path.
Treating the shaft of the motor prior to installing the AEGIS® Ring:
1. Shaft must be clean and free of any coatings, paint, or other
nonconductive material. The shaft must be clean to bare metal.
2. Thoroughly stir the silver coating.
Apply a light coat of the AEGIS® Colloidal Silver Shaft Coating to the
area where the AEGIS® microfibers are in contact with the motor
Colloidal Silver shaft. Apply evenly all around the shaft. Allow to dry. Coating will
Shaft Coating cure at room temperature in 16-20 hours or in 30 minutes at 120-
PN# CS015 200˚C. A heat gun will cure the materials in seconds.
3. Apply a second coat for best coverage. Allow to dry. After coating is
dry, install the AEGIS® Shaft Grounding Ring.
Follow all safety precautions. MSDS for CS015 available for
download at www.est-aegis.com
Install the AEGIS® SGR so that the aluminum frame maintains an even
clearance around the shaft. AEGIS® conductive microfibers must be in
contact with conductive metal surface of the shaft.
STOP
Do not use thread lock to secure the mounting screws as it may
compromise the conductive path to ground.
If thread lock is required, use a small amount of EP2400 AEGIS®

Conductive Epoxy to secure the screws in place.
After installation, test for a conductive path to ground using an Ohm

meter. Place one probe on metal frame of AEGIS® SGR and one probe on
motor frame.
Motor must be grounded to common earth ground with drive
according to applicable standards.
Where AEGIS® SGR is exposed to excessive debris, additional protection of

the AEGIS® SGR fibers may be necessary.
Install an o-ring or v-slinger against the ring.
Contact AEGIS® Customer Service/Engineering for assistance with specific

applications.

Patented Technology
AEGIS® SGR for Low Voltage and iPRO for Medium Voltage Motors
LOW VOLTAGE MOTORS MEDIUM VOLTAGE MOTORS

Supply voltage: 600 VAC or less Supply voltage: greater than 600 VAC
Recommended Technology: AEGIS® SGR Recommended Technology: AEGIS® iPRO
Motors over 100 HP - recommend isolation of one Recommend isolation of one bearing and AEGIS®
bearing and AEGIS® SGR on the opposite bearing. iPRO on the opposite bearing.
6 rows of Conductive MicroFiber
Description: Description:
• Design Type: AEGIS® SGR • Design Type: AEGIS® iPRO
• Circumferential Conductive MicroFiber rows in • Circumferential Conductive MicroFiber rows in
FiberLock™ Channel FiberLock™ Channel
• Rows of fiber: 2 • Rows of fiber: 6
• Fiber overlaps shaft 0.030” (.76mm) • Fiber overlaps shaft 0.030” (.76mm)
• OAL: 0.295” (7.5mm) • OAL: 0.625” (15.875mm)
• OD: listed in AEGIS® Catalog • OD: Shaft + (refer to drawing)
Mounting: Mounting:
• Internal or External • Internal or External
• Select based on shaft diameter • Select based on shaft diameter
• Split or Solid versions available • Split or Solid versions available
• Custom brackets optional • Custom brackets optional
AEGIS® SGR Current Capability Chart AEGIS® iPRO Current Capability Chart
AEGIS® Shaft Grounding Ring AEGIS® iPRO Grounding Ring

HF Current Discharge Capability (amps at 50 watts) High Frequency Current Discharge Capability
70 (amps at 50 watts)
250
Current (amps)
Current (amps)
60
50 200
40 150
30
100
20
50
10
0 0
0.5" (12.5mm) 1" (25mm) 2" (50mm) 4" (100mm) 8" (200mm) 2" (50mm) 4" (100mm) 8" (200mm) 16" (400mm) 32" (800mm)

Patented Technology
AEGIS® Installation - Internal

AEGIS® Bearing Protection Rings are ideally installed on the inside of the motor to provide protection from ingress of dirt and dust.
Motor manufacturers commonly use this installation as a best practice in stock catalog motors equipped with AEGIS® rings.
Follow all safety precautions. MSDS for CS015 and EP2400 available for download at www.est-aegis.com
Follow AEGIS® best practices for motor shaft preparation and ring installation. Use AEGIS® Colloidal Silver
Shaft Coating when installing AEGIS® rings to enhance the shaft conductivity and help prevent oxidation.
Press Fit Installation into:

• Bearing Retainer
• Custom Bracket
Bore Specification: 0.002” – 0.004” interference [.05 mm - .10 mm]
English: Ring OD tolerance +0 / -0.001” Bore tolerance +0.001 / -0”
Metric: Ring OD tolerance +0 / -0.025 mm Bore tolerance +0.025 / -0 mm
Bolt-through installation into: STOP

Do not use non-conductive
• Bearing Retainer thread-lock
• Custom Bracket
Drill/tap holes per AEGIS® Ring Use EP2400 Conductive Epoxy
drawing location if thread lock is needed to
• Flat head cap screws secure the screws in place.
• Socket head cap screws/lock washer
In some motors it may be desirable to attach an additional machined spacer to

locate the ring further away from the bearing grease cavity.
A grease seal may be added to reduce grease ingress to the fibers.
Photo courtesy of Independent Electric
Bearing
Retainer
Common AEGIS® Ring installation internal to the motor is on the motor’s bearing
AEGIS®SGR retainer. Installation can be done with bolt through hardware or AEGIS®
Conductive Epoxy.
Shaft For epoxy installation, bearing retainer must be clean & free of any coatings,
paint, or other nonconductive material where AEGIS® SGR will be mounted. This
Rotor End
is the discharge path to ground therefore metal to metal contact is essential.
Bracket
Epoxy Mounting – Internal

AEGIS® Conductive Epoxy was specially developed and tested to stringent
vibration and pull test requirements to ensure a strong and reliable long term
adhesive bond.
STOP
Do not use a substitute epoxy as only the AEGIS® EP2400 has been tested
and approved for AEGIS® ring installation.

Patented Technology
AEGIS® Installation - External

AEGIS® Bearing Protection Rings may be installed on the outside of the motor but care must be taken to protect the ring from
excessive ingress of dirt and dust.
Follow AEGIS® best practices for motor shaft preparation and ring installation. Use AEGIS® Colloidal Silver
Shaft Coating when installing AEGIS® rings to enhance the shaft conductivity and help prevent oxidation.
An o-ring or “v’” slinger may be installed against the AEGIS® Ring to help prevent excessive ingress of dirt,
dust or liquid.
Standard bracket or uKIT bracket Installation: uKIT with o-ring

• Standard Brackets (3 or 4 depending on ring size)
• uKIT includes various bracket options
• Custom brackets available
To view product line or download the AEGIS® Catalog
visit www.est-aegis.com
Severe Duty Motors: Install Garlock SGi with AEGIS® Shaft Grounding
Bearing
Technology. For technical Information visit www.klozure.com
Isolator
• Garlock SGi – Shaft Grounding Bearing Isolator may be installed into a
bearing isolator cavity
• Motor End Bracket may be bored out to allow for Garlock SGi to be
installed Garlock SGi
• Solid or Split version available with AEGIS® SGR
Bolt-through installation into: STOP

Do not use non-conductive
• End Bracket thread-lock
• Custom Bracket
Use EP2400 Conductive Epoxy
Drill/tap holes per AEGIS® Ring if thread lock is needed to
drawing location secure the screws in place.
• Flat head cap screws
• Socket head cap screws/lock washer
Epoxy Mounting – External

Motor end bracket must be clean & free of any coatings, paint, or other
nonconductive material where AEGIS® SGR will be mounted using conductive
epoxy. This is the discharge path to ground therefore metal to metal contact is
essential.
Curing can be achieved in 4 hours at or above 75° F (24°C). For faster curing
times, maximum conductivity and adhesion, heat the bond to between 150°-
250° F (66°-121° C) for 10 minutes and allow to cool.
Pot-life is approximately 10 minutes at 75° F (24° C).
AEGIS® Conductive Epoxy was specially developed and tested to stringent
vibration and pull test requirements to ensure a strong and reliable long term
adhesive bond.
Do not use a substitute epoxy as only the AEGIS® EP2400 has been
STOP
tested and approved for AEGIS® ring installation.

Patented Technology
Motors up to and including 100 HP (75 kW) - Low Voltage

General recommendations: For induction motors
Internal or external
either foot mounted, c-face or d-flange mounted
installation
motors with single row radial ball bearings on
both ends of the motor. Motors may be installed
either horizontally or vertically in the customer’s
application.
• Install one AEGIS® SGR Bearing Protection
Ring on either the drive end or the non-drive
end of the motor to discharge capacitive
induced shaft voltage.
• AEGIS® SGR may be installed either internally
or externally.
• Use AEGIS® Colloidal Silver Shaft Coating
(PN# CS015) on motor shaft where fibers
touch.
Product recommendation: AEGIS® SGR
Follow all safety precautions. MSDS available

for download at www.est-aegis.com
Motors Greater than 100 HP (75 kW) For horizontally mounted motors with single
row radial ball bearings on both ends of the
sleeve motor:
• Non-Drive end: Bearing housing must be
isolated with insulated sleeve or coating or
use insulated ceramic or hybrid bearing to
disrupt circulating currents.
• Drive end: Install one AEGIS® Bearing
Protection Ring .
• AEGIS® Ring can be installed internally on
the back of the bearing cap or externally on
the motor end bracket.
• Use AEGIS® Colloidal Silver Shaft Coating
(PN# CS015) on motor shaft where fibers
touch.
Product recommendation:
Low Voltage Motors up to 500HP:
AEGIS® SGR
Install AEGIS® Ring on opposite end of insulation Low Voltage Motors over 500HP:
AEGIS®iPRO
Medium Voltage Motors: AEGIS® iPRO
For Technical Support: [email protected] or call 1-866-738-1857

Patented Technology
Motors Where Both Bearings are Insulated - Any HP/kW

Low Voltage or Medium Voltage Motors:
sleeve
• Install one AEGIS® Bearing Protection Ring,

drive end preferred, to protect bearings in
attached equipment (gearbox, pump, fan
bearing and encoder, etc...).
• Colloidal Silver Shaft Coating PN CS015 is
required for this type of application.
Low Voltage Motors: AEGIS® SGR
Install AEGIS® Ring on opposite end of insulation
Bearings in attached equipment may be at

STOP
risk from VFD induced shaft voltage unless
AEGIS® Shaft Grounding is installed.
Motors with Cylindrical Roller, Babbitt or Sleeve Bearings:
• Cylindrical Roller Bearing, Babbitt, or Sleeve

bearing: Bearing housing should be isolated sleeve
or use insulated bearing.
• Motors with insulated cylindrical roller
bearing DE: Install AEGIS® Bearing Protection
Ring on opposite drive end (NDE).
Note: If an insulated cylindrical roller bearing or sleeve is not

possible, then isolate the opposite bearing and install an
AEGIS® Ring at the cylindrical roller bearing side.
Install AEGIS® Ring on opposite end of insulation

Patented Technology
Vertical Solid Shaft Motors up to and including 100 HP (75 kW) -

Low Voltage:
• Lower Bearing: Install one AEGIS® SGR

V Bearing Protection Ring.
F
R S
H D • AEGIS® SGR can be installed internally on the
O
T A back of the bearing cap or externally on the
F
S
T
O Shaft Currents
T motor end bracket.
R
A C • Colloidal Silver Shaft Coating PN CS015 is
T U
O R required for this type of application.
R R
E Product recommendation: AEGIS® SGR
N
T
S
Follow all safety precautions. MSDS available

for download at www.est-aegis.com
PUMP
Ground
Vertical Solid Shaft Motors Greater than 100 HP (75 kW):
isolate • Upper Bearing: Bearing journal must be

V
F isolated or insulated ceramic or hybrid
R S
O H D ceramic bearing installed.
T A
sleeve S F • Bottom Bearing: Install one AEGIS® Bearing
Shaft Currents
O T
T R Protection Ring.
A C
T U • AEGIS® Ring can be installed internally on
R
O
R the back of the bearing cap or externally on
R
E
N
T
S • Colloidal Silver Shaft Coating PN CS015 is
PUMP
Ground

Patented Technology
Vertical Hollow Shaft Motors up to and including 100 HP (75 kW) -

Low Voltage :
• Lower Bearing: Install one AEGIS® SGR Bearing
Protection Ring. Bearing
Carrier
• AEGIS® SGR can be installed internally on the Thrust

Bearing
back of the bearing cap.

• Colloidal Silver Shaft Coating PN CS015 is Shaft
required for this type of application. Currents
Head Shaft
Product recommendation: AEGIS® SGR
Stator
Stator
Rotor
Hollow Shaft
Note: For external installation, the AEGIS® Ring

must run on the motor or pump shaft at Shaft
AEGIS® Ring
Currents
the lower bearing. Ring must not be
Guide
mounted around the steady bushing. Bearing
Upper bearing may be isolated with Ground

insulated bearing carrier for added
protection. Driven Equipment
Vertical Hollow Shaft Motors Greater than 100 HP (75 kW) :
Insulated
Bearing
Carrier Thrust
• Upper Bearing: Bearing carrier must be Bearing
isolated or insulated ceramic or hybrid ceramic

bearing installed. Shaft
Currents
• Lower Bearing: Install one AEGIS® Bearing
Head Shaft
Protection Ring.
Stator
Stator
Rotor
• AEGIS® Ring can be installed internally on the

back of the bearing cap.
Hollow Shaft
required for this type of application. Shaft
Currents AEGIS® Ring
Product recommendation: Isolated Bearing
Low Voltage Motors: AEGIS® SGR can be added for
additional assurance
Medium Voltage Motors: AEGIS® iPRO Ground
Driven Equipment
Application notes are intended as general guidance to assist with proper application of AEGIS® Bearing Protection Ring to protect motor bearings.
All statements and technical information contained in the application notes are rendered in good faith. User must assume responsibility to
determine suitability of the product for its intended use.

Patented Technology
AEGIS® Technology
AEGIS® Shaft Grounding Rings Provide Both Contact and Noncontact Grounding
The Only Product of its Kind
AEGIS® Bearing Protection Ring uses Revolutionary

Nanogap Technology
• Unique contact/non-contact design
• 360 degrees circumferential conductive micro fiber ring
• Multiple row design – greatest reliability
• Ensures unmatched shaft grounding and performance
The AEGIS® Bearing Protection Ring’s patented Nanogap Technology ensures effective
® SGR electrical contact even when physical contact is broken . Only AEGIS® Nanogap
BEARING PROTECTION RING Technology provides both maintenance-free contact and noncontact bearing
protection for the normal service life of the motor’s bearings as well as the most
reliable operation of any shaft grounding technology.
Proprietary Conductive Microfibers Last for the Service Life of the Motor
The AEGIS® Bearing Protection Ring’s unique design features hundreds of thousands to
millions of specially engineered conductive microfibers that encircle the motor shaft. With
so many electrical transfer points the ring provides continuous electrical contact, whether
its fibers are physically touching the shaft or not. This patented “nanogap” technology
enables both contact and noncontact shaft grounding — 100% of the time.
Specially Designed Microfibers Flex Without Breaking

Designed with specific mechanical and electrical characteristics that minimize wear and
maintain conductivity, AEGIS® microfibers will last for the life of the motor. Based on wear of
less than 0.001” (0.025mm) during 10,000 hours of testing, proven to withstand over 200,000
Shaft hours of continuous operation.
Through our patented design, AEGIS® conductive microfibers exhibit minimal wear and the
ability to flex without breaking. In testing, they were proven to withstand 2 million direction
reversals (to 1800 RPM) with no fiber fatigue or breakage.
AEGIS® Rings are designed with an optimal fiber overlap to the shaft of 0.030” (0.76mm).
AEGIS®
Ring Patented FiberLock™ Channel Secures and Protects Fibers
AEGIS’s patented, protective FiberLock™ channel locks the ring’s conductive microfibers
securely in place around the motor shaft, allowing them to flex without breaking. The
Shaft channel also helps protect the fibers from excessive dirt, oil, grease, and other contaminants.
FiberLock™
Channel

Patented Technology
AEGIS® Technology
Ensures Unmatched Grounding With or Without Shaft Contact

At any point in time, the AEGIS® microfibers are in mechanical contact with the shaft and those that aren’t are in nanogap
proximity due its unique design. Thanks to the patented Electron Transport Technology™, all of the ring’s fibers remain in
electrical contact with the motor shaft providing unmatched grounding 100% of the time. This technology ensures electrical
contact for the life of the motor through mechanical contact and three simultaneous nanogap noncontact current transfer
processes. These processes ensure effective grounding even in the presence of grease, oil, dust and other contaminants,
regardless of the motor’s speed. No other product works with and without contacting the motor shaft to provide the long-
term and maintenance-free bearing protection of the AEGIS® Ring.
Tunneling Field Emissions Townsend Avalanche

of Electrons of Electrons of Gaseous Ions
This mechanism is based on the Field emission is a form of quantum This process results from the
ability of electrons to “tunnel” tunneling whereby electrons cascading effect of secondary
across an insulating barrier, and move through a barrier in the electrons released by collisions
works for gaps smaller than 2 nm. presence of a high electric field. It and the impact ionization of gas
provides grounding across gaps of ions accelerating across gaps
2 nm to 5 μm. The electric field greater than 5 μm. This ionization
from the shaft voltages creates the creates negative and positive ions
conditions for the AEGIS® ring which neutralize the shaft voltage.
fibers to take advantage of field
emission electron transfer from
the shaft.
AEGIS® Bearing Protection Ring vs. Contact-Only Brush

The chart below compares the design and performance characteristics of AEGIS® Rings to those of conventional and discrete-
point grounding brushes that work only through contact with the motor shaft. Due to its patented design and proprietary
conductive microfibers, the AEGIS® Ring maintains electrical contact with the motor shaft even if mechanical contact is broken.
No other shaft grounding brush provides such exceptional bearing protection.
Performance Characteristic AEGIS® Ring Contact-Only Brush

Continuous circumferential ring design Yes No
Contact and Noncontact electrical shaft grounding Yes No
Protective fiber channel Yes No
Ultra-low wear fibers / wear-to-fit fiber design Yes No
Maintenance-free Yes No
Effective in presence of dust, dirt, oil, and grease Yes No

Patented Technology
AEGIS® Technology
Manufacturer’s Specification
Fiber Flexibility AEGIS® Rings are constructed with patented AEGIS® FiberLock™ channel to allow
conductive micro fibers to bend and flex within their elastic design limits. Fibers
are distributed 360 degrees inside the FiberLock™ channel to provide maximum
shaft surface contact with multiple rows. Fiber length is designed with an optimal
shaft overlap of 0.030” (0.76mm).
Fiber wear Usually less than 0.001” in 10,000 hours. Fiber wear length is designed for expected
life of 200,000+ hours based on testing. Wear rate may vary depending on
conditions in individual applications. Fibers retain contact/noncontact function.
Friction Little or no frictional axial or radial fiber pressure applied to shaft. Extremely light
contact only. Designed for minimal friction with no reduction in motor
performance.
AEGIS® Bearing Protection Ring None
Maintenance Requirements
Oil and Grease on Motor Shaft Small amounts of oil and/or grease are acceptable as long as the shaft surface
remains conductive. Fibers are designed to maintain contact with the motor shaft
and “sweep” oil away from surface.
Dirt/dust Small amounts of dust and/or small particles are acceptable. Fibers “sweep”
particles from shaft surface during operation. Shaft surface must remain
conductive.
Directional rotation Motor may be operated in clockwise or counter clockwise rotation. Motor may
change directional rotation without limitations.
Maximum surface rate/RPM No Maximum rating - There is no theoretical RPM limit as there is virtually no
frictional contact with the shaft at high RPM. Verify any specific application with
AEGIS® engineering.
Maximum temperature rating 410 F/210 C - Verify application specific temperatures with AEGIS® engineering.
Minimum temperature rating -112 degrees F/-80C - Verify application specific temperatures with AEGIS®
engineering.
Humidity 0 to 90% - Verify application specific acceptable humidity with AEGIS® engineering
RoHS Test Results All materials used in manufacture of AEGIS® Rings are in compliance with Directive
2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical
and electronic equipment. No RoHS banned substances are present in excess of
Directive 2002/95/EC for the the maximum concentration values (MCV).
Restriction of the use of certain 1. Following substances were found to be less than 0.1% by weight in
Hazardous Substances in electrical homogeneous materials (required by RoHS directive):
and electronic equipment applies Lead (Pb)
Mercury (Hg)
Hexavalent chromium (Cr(VI))
Polybrominated biphenyl (PBB)
Polybrominated diphenyl ether (PDPE)
2. Following substance is less than 0.01% by weight in homogeneous materials
(required by RoHS directive):
Cadmium (Cd)
Note: Request RoHS Certification Letter from [email protected] or call 1-866-
738-1857
Hazardous areas Not certified for hazardous environments (Class 1 Division 1, Division 2 or Class 1
Zone 1, Zone 2)
CE and UL requirements AEGIS® Rings are classified as a “component” and as such are not subject to the
requirements of any Directive. The application of CE or UL Mark is not applicable
to this component.

Patented Technology
Testing for Shaft Voltages (Before & After)
Testing and Analysis Services - Measuring Shaft Voltages
Shaft Voltage Test Report: Measuring the shaft voltage on VFD driven
motors provides the end user with valuable information to determine if there
is a potential risk of bearing damage from electrical bearing discharges.
Surveying and documenting shaft voltage readings and wave forms will assist
in determining the appropriate mitigation or solution.
Note: The best time for shaft voltage measurements are during initial start-up
in new or repaired motors operated by the VFD. Shaft voltage measurements
should be incorporated into preventive and predictive maintenance programs
and may be combined with vibration analysis, thermography or other services.
Report template available at: www.est-aegis.com/bearing
AEGIS® SVP Shaft Voltage Probe

The AEGIS® SVP Shaft Voltage Probe tip
attaches to an oscilloscope voltage
probe to easily and accurately measure
the voltage on a rotating shaft. The high
density of conductive microfibers
ensures continuous contact with the
rotating shaft. The AEGIS® SVP can be
hand held or used with a magnetic base.
Caution: Use appropriate

safety procedures near
rotating equipment.
PN: SVP-KIT-3000MB
Recommended Testing Equipment

• Oscilloscope with a 10:1 probe. We recommend a
minimum 100MHz bandwidth to accurately measure
the waveform.
• AEGIS® SVP Shaft Voltage Probe Kit PN SVP-KIT-
3000MB (for Fluke 199c and 190 II series) Contact EST
if you have a different size voltage probe.
• Recommend Fluke ScopeMeter® 190 Series or
equivalent.

Patented Technology
Testing for Shaft Voltages
Examples of Shaft Voltage Readings

High Peak to Peak common mode voltage –
Typically 20 to 120 volts peak to peak. The waveform image shows the
capacitive coupled common mode voltage on the shaft of the motor.
The “six-step” wave form is the result of the 3 phases of pulses from the
VFD. The timing of the pulse width modulation (PWM) pulses to the
motor from the drive determines what the wave form looks like.
Sometimes it will look like a square wave.
This six-step or square wave is what is seen when there is no bearing
discharge and the peak to peak shaft voltage is at it’s maximum level.
The voltage level may eventually overcome the dielectric in most non-
isolated bearings and begin discharging.
The use of cursors is handy to determine voltages
at a specific spot in the reading.
High amplitude EDM discharge pattern –

Typically EDM discharges can occur from 6 volts peak to 80 volts peak
depending on the motor, the type of bearing, the age of the bearing,
and other factors. The waveform image shows an increase in voltage
on the shaft and then a sharp vertical line indicating a voltage
discharge. This can occur thousands of times in a second, based on the
carrier frequency of the drive. The sharp vertical discharge at the
trailing edge of the voltage is an ultra high frequency dv/dt with a
typical “discharge frequency” of 1 to 125 MHz (based on testing results
in many applications).
Low amplitude voltage discharge pattern –

Typically the peak to peak voltages are 4 to 15 volts peak to peak. The
waveform image shows a more continuous discharge pattern with
lower dv/dt frequencies between 30 KHz to 1 MHz. The lower voltage
is due to greater current flow in the bearings which is the result of the
bearing lubrication becoming conductive. As discharges occur in the
bearings, the lubrication is contaminated with carbon and metal
particles. The lower impedance to the shaft voltages results in lower
peak to peak voltages. This condition is usually found in motors that
have been in operation for many months or years.
Peak to Peak voltage with AEGIS® ring installed –

With the AEGIS® ring installed, you will typically see discharge voltage
peaks around 2 to 3 volts on a bare steel shaft surface. The voltage
readings may be decreased with the application of AEGIS® Colloidal
Silver Shaft Coating which allows for a more efficient electron transfer
to the conductive micro fiber tips. The waveform image shows the low
peak to peak waveform of a motor with the AEGIS® SGR ring installed
and discharging the shaft voltages.

Patented Technology
Set Amplitude
An EDM discharge pattern will show a climb in voltage and then a sharp vertical
line. The sharp vertical line shows the moment of discharge to ground. Each
motor will have its own unique parameters.
Control the vertical span of the displayed signal by adjusting the volts per
division. The signal peak to peak should all be displayed on the screen. 5V is a
good place to start and then adjust based on the conditions.
Press “mV” to increase vertical sensitivity
Press “V” to decrease vertical sensitivity
This is an example of amplitude set

to 5 volts per division. The trace is
clearly shown. If the peak extends
beyond the screen, decrease the
amplitude.
Set Time Period

Control the horizontal span of the displayed signal by adjusting the Time. 400µs
(microseconds) is a good place to start and then adjust TIME based on the
conditions.
Press “ns” to increase horizontal sensitivity

Press “s” to decrease horizontal sensitivity
This is an example of a Time period

set to 4 microseconds (4/1,000,000).
It clearly shows a climb in voltage
and a sharp discharge to ground.

Patented Technology
Taking the Measurements- EMI
Ground Reference Reading: EMI
1. The reading displays ground noise or EMI being produced by the

motor/drive system. This electrical noise may be present before
and after installing the AEGIS® ring.
2. Find 2 ground points on the motor. Must be bare metal and

conductive.
3. Place the SVP on one of the points and the probe grounding clip
on the other point.
4. Measurements will vary depending on the motor size and

conditions.
Taking the Measurements- Shaft Voltage
Shaft Voltage Reading
1. Shaft must be clean & free of any coatings, paint or other

nonconductive material.
2. Secure the probe in place with magnetic base.
3. Align AEGIS® SVP on shaft end or side ensuring continuous

contact. Avoid keyway if possible.
4. Place oscilloscope grounding lead on bare metal of motor

ensuring conductive path to ground.
5. If you plan to create a report for the customer, save the image.
Follow all safety precaution when working with rotating

equipment.

Patented Technology
Measurements Using the AEGIS® Grounding Simulator

The AEGIS® Grounding Simulator can be used to simulate how the
shaft voltages will change after an AEGIS® Ring is installed. It is a
quick way of showing a “Before & After” .
1. Take the Shaft Voltage Reading without Shaft Grounding

2. Take the Shaft Voltage Reading with the AEGIS® Grounding Simulator
AEGIS® Grounding
Simulator
First Take the Shaft Voltage Reading without Shaft Grounding
1. Shaft must be clean & free of any coatings, paint or other nonconductive
material.
2. Secure the probe in place with magnetic base.
3. Align AEGIS® SVP on shaft end or side ensuring continuous contact.
Avoid keyway if possible.
4. Place oscilloscope grounding lead on bare metal of motor ensuring
conductive path to ground.
5. Save the image. Please refer to page 25 for this action.
The voltage measurement of 31.2V peak to peak is an example of the voltage

discharging through the bearings without AEGIS® shaft grounding.

equipment.
Next Take the Shaft Voltage Reading with the Simulator

Grounding the Shaft
1. Maintain the same setup as above.

2. Place the AEGIS® Grounding Simulator grounding lead on bare metal of
motor ensuring conductive path to ground.
3. Place the Simulator against the shaft to simulate the AEGIS® SGR
Bearing Protection Ring.
4. Save the image.
The voltage measurement of 1.2V peak to peak is an example of the voltage

discharging through the Simulator to ground. The AEGIS® SGR Bearing
Protection Ring will perform equally or better.

equipment.

Patented Technology
ScopeMeter Saving Images as .BMP on USB
1. Plug in a USB drive

2. Saving images as .BMP allow you to view your file without using the Fluke
software on your computer.
3. You will not be able to change the file name as you are saving it but you
can change it later.
4. Hold Image on screen
5. Save
6. F1 Save
7. F1 again to change from INT to USB (this is not saving the file)
8. F4 Close
9. F3 to save to USB
10. Press Clear to Clear menu
11. To view USB saved files, use a computer.
AEGIS® SVP Part Numbers:
SVP-KIT-3000MB Catalog Number Includes:

3 SVP tips, probe holder with two piece extension rod (total length
SVP-KIT-3000MB of probe holder with extension rod is 18 inches), AEGIS® Grounding
Simulator, and magnetic base.
3 SVP tips, probe holder with two piece extension rod, and AEGIS®
SVP-KIT-3000
Grounding Simulator.
SVP-KIT-3000 SVP-TIP-3000 3 SVP tips
Fits Fluke Voltage Probe VPS410 and VPS200; for other sizes see our website www.est-aegis.com
SVP-TIP-3000

Patented Technology
Probe Tip Installation & ScopeMeter Set Up
AEGIS® SVP Tip Installation

Fluke VPS410 10:1 probe
1. Remove the protective cap 2. Remove the plastic sleeve
3. Probe with sleeve removed 4. Attach ground lead
5. Install the AEGIS® SVP tip over the 6. Secure the tip to the probe using the
probe tip thumb screw. Be careful not to over
tighten.

Patented Technology
Setting the ScopeMeter Parameters
Connect 10:1
probe in Input A The following pages describe the parameters we use to
capture shaft voltages. Although not all meters have the same
options, the basic concept is the same.
To demonstrate, we will use the Fluke 190-204 ScopeMeter®

4 channel - 200 MHz. Refer to your owner’s manual for a
different meter.
Use the toggle keys in the middle to toggle through the

menu. Always press the ENTER button to confirm your
actions.
ScopeMeter Parameters Set Readings “ON”
Press the A button for Press SCOPE

channel A. Menu will Press F1 to toggle ON
appear at the bottom. Press SCOPE to clear
menu.

Patented Technology
ScopeMeter Parameters DC Coupling
Press the A button for Press F2 COUPLING to toggle DC Coupling will pick up
channel A. Menu will between the DC and AC DC and AC voltages.
appear at the bottom. Coupling.
Choose DC and press ENTER.
Press CLEAR to clear menu.
ScopeMeter Parameters Set Voltage Peak-Peak
Press the SCOPE button. Press F2 READING. Cursor Use up/down arrows to
A menu will appear at the to desired channel and choose Peak and press
bottom. press ENTER. ENTER.

Patented Technology
ScopeMeter Parameters Set Voltage Peak-Peak
Voltage Peak to Peak is

now set.
Choose Peak to Peak and Press CLEAR to remove

press ENTER. the menu bar.
ScopeMeter Parameters Set Polarity and Bandwidth
Press A button Press F4 INPUT A OPTIONS Column 1 choose Normal

Menu will appear at the and press ENTER.
bottom. Column 2 choose Full and
press ENTER.
Press CLEAR to clear the
menu.

Patented Technology
ScopeMeter Parameters Set Waveform Averages “OFF” and

Waveform “Normal”
To show specific voltage Move cursor to 3rd In column 4

measurements instead of column Waveform: Normal
averages: Averages: OFF Press ENTER
Press the SCOPE button Press ENTER Press CLEAR to clear the
Press F4 WAVEFORM menu
OPTIONS
ScopeMeter Parameters Set Voltage Amplitude
Amplitude will need to be In this example the In this example the

adjusted according to the amplitude is too small. amplitude is too large.
conditions. Increase RANGE (mV) to Decrease RANGE (V) to
Set to show complete sign show more detail. show top and bottom
wave from top peak to peaks.
bottom peak using the
RANGE button.

Patented Technology
Selecting the Correct Size Ring
For standard NEMA or IEC frame motors, the AEGIS® uKIT is the best option.
It avoids most shaft shoulders and slingers/seals.
AEGIS® uKit includes 4 different bracket sizes to suit most situations.
STOP Question to ask: Does the motor have a shaft shoulder?
If YES or NOT SURE, then the AEGIS® uKIT is a great options because it avoids the shaft shoulder area, any slingers/seals
or irregular shaped end bracket.
AEGIS® uKIT is be attached to motor

with screws/washers provided or with
conductive epoxy. AEGIS® EP2400
Motor Conductive Epoxy sold separately.
End
See AEGIS® website for bolt hole circle
Bracket
Measure Shaft and installation instructions.
Diameter Here
See page 38 for more details.
Avoids Shaft Shoulder
Avoids Slinger / Seal
If NO, the ring can be mounted directly to the end bracket using screws or conductive epoxy.
(.295” thick) Measure shaft diameter at a point 0.125” from

Example shaft
motor end bracket. Then refer to the parts list to measurement
AEGIS® Ring
locate the correct part number and mounting 0.445”
Shaft
option of your choosing. fits between
Motor
End
Bracket
Solid Ring with Split Ring* with Solid Ring Split Ring* Bolt Through* Min. Shaft Max. Shaft
Measure 0.125” Conductive Epoxy Conductive Epoxy Catalog Number Catalog Number Catalog Number Diameter Diameter
from end bracket.
SGR-9.0-0AW SGR-9.0-0A4W SGR-9.0-1 SGR-9.0-1A4 SGR-9.0-3FH 0.396 0.435
If YES and you want to mount the ring to fit the shaft shoulder then you need to measure the length of the shoulder. See
note in red below. If still applicable, measure shaft shoulder diameter then refer to parts list (as shown above) to locate the
correct SGR part number.
Custom Option for Short Shaft Shoulders: If the
shaft shoulder is between .1875” and 0.375” we
(.295” thick)
offer a custom part with fibers closer to the back
of the ring. To order this option, add an “X” or “AX”
AEGIS® Ring
to the suffix of the part.
Shaft
Motor
End Example:
Bracket Standard SGR Short Shoulder SGR
PN: SGR-6.9-0A4W PN: SGR-6.9-0A4WX
• Screw on mounting - shaft length needs PN: SGR-6.9-0AW PN: SGR-6.9-0AWX
to be a minimum of 0.375” (9.5mm). PN: SGR-6.9-1 PN: SGR-6.9-1AX
PN: SGR-6.9-1A4 PN: SGR-6.9-1A4X
• Conductive epoxy mounting - shaft length PN: SGR-6.9-3FH PN: SGR-6.9-3FHAX
needs to be a mimimum of 0.395” (10.03mm).
If the shoulder is less than 0.1875”, then refer to the uKIT.

Patented Technology
AEGIS® Bearing Protection Ring Parts List
AEGIS® SGR Bearing Protection Ring Options

uKIT - SGR with Universal Mounting Bracket
pg. 38-39 Sized for NEMA and IEC Frame motors
Solid and Split Ring
Can be mounted with hardware or conductive epoxy
Conductive Epoxy Mounting (-0AW, -0A4W)

pg. 40-41 Shaft diameters: 0.311” to 6.02”
Solid and Split Ring
Quick and easy installation to metal motor frame
Conductive Epoxy Included
Standard Mounting Brackets (-1)

3 to 4 mounting brackets, 6-32 x 1/4” cap screws and washers
Quick and easy installation to most surfaces
Split Ring (-1A4)

pg. 40-41 Shaft diameter: 0.311” to 6.02”
4 to 6 mounting brackets, 6-32 x 1/4” cap screws and washers
Installs without decoupling motor
Bolt Through Mounting (-3FH)

6-32 x 1/2” flat head screws
2 mounting holes up to shaft size 3.895”
4 mounting holes for larger sizes
Press Fit Mounting (-0A6)

pg.42 Shaft diameters: 0.311” to 6.02”
Clean dry 0.004” press fit
Custom sizes available
NEMA-IEC Mounting Kits

pg. 43 Shaft diameter: see chart for standard kits
Custom kits available for other shaft diameters
Clears any slinger, shaft shoulder or protrusion
Large SGR, iPRO, WTG

pg.44 Large Rings over 6.02”
iPRO for Medium Voltage Motors
WTG for Wind Turbine Generators
Accessories
pg.45 SVP - AEGIS® Shaft Voltage Probe
CS015 - AEGIS® Colloidal Silver Shaft Coating
EP2400 - AEGIS® Conductive Epoxy

Patented Technology
AEGIS® uKIT with Universal Mounting

for NEMA and IEC Motors
Solid and Split Ring Design
Split Ring
• Kit is designed to avoid any slinger or

shaft shoulder. Order based on NEMA
and IEC Frame size.
• Install with 3 or 4 brackets depending
on motor end bracket design.
• uKIT can be attached to motor with
screws/washers provided or with
conductive epoxy. AEGIS® EP2400
Conductive Epoxy sold separately.
• See AEGIS® website for bolt hole circle
and installation.
AEGIS® SGR uKit Includes: Hardware for NEMA Motors also Include: Hardware for IEC Motors also Include:
(1) AEGIS® SGR Bearing Protection Ring (4) 5-40 x 3/8” flat head screws (4) 5-40 x 3/8” flat head screws
(4) universal brackets of each size - 16 total (4) 6-32 x 3/8” socket head cap screws (4) M4 x 10 socket head cap screws
(4) #6 split lock washers (4) M4 split lock washers
(4) #6 flat washers (4) M4 flat washers
5/64” allen wrench 5/64” allen wrench
7/64” allen wrench 3mm allen wrench
Drill and tap hardware installation AEGIS® EP2400 Conductive Epoxy installation Solid Ring with 3 bracket installation

Patented Technology
AEGIS® uKIT with Universal Mounting

for NEMA and IEC Motors
NEMA NEMA NEMA
uKIT Catalog Number uKIT Catalog Number Motor shaft NEMA Frame
Solid Split dia “u”
SGR-0.625-UKIT SGR-0.625-UKIT-1A4 0.625” 56
SGR-0.875-UKIT SGR-0.875-UKIT-1A4 0.875” 56HZ, 143T, 145T
SGR-1.125-UKIT SGR-1.125-UKIT-1A4 1.125” 182T, 184T
SGR-1.625-UKIT SGR-1.625-UKIT-1A4 1.625” 254T, 256T, 284TS, 286TS
SGR-1.875-UKIT SGR-1.875-UKIT-1A4 1.875” 284T, 286T, 324TS, 326TS, 364TS, 365TS
SGR-2.125-UKIT SGR-2.125-UKIT-1A4 2.125” 324T, 326T, 404TS, 405TS
SGR-2.375-UKIT SGR-2.375-UKIT-1A4 2.375” 364T, 365T, 444TS, 445TS, 447TS, 449TS
SGR-3.375-UKIT SGR-3.375-UKIT-1A4 3.375” 444T, 445T, 447T, 449T
SGR-3.625-UKIT SGR-3.625-UKIT-1A4 3.625”
IEC IEC IEC

uKIT Catalog Number uKIT Catalog Number Motor shaft IEC Frame
Solid Split dia “u”
SGR-28-UKIT SGR-28-UKIT-2A4 28mm IEC 100L, 112M (2, 4, 6, 8 pole)
SGR-38-UKIT SGR-38-UKIT-2A4 38mm IEC 132S, 132M (2, 4, 6, 8 pole)
SGR-42-UKIT SGR-42-UKIT-2A4 42mm IEC 160M, 160L (2, 4, 6, 8 pole)
SGR-48-UKIT SGR-48-UKIT-2A4 48mm IEC 180M, 180L (2, 4, 6, 8 pole)
SGR-55-UKIT SGR-55-UKIT-2A4 55mm IEC 200L (2, 4, 6, 8 pole); IEC 225S, 225M (2 pole)
SGR-60-UKIT SGR-60-UKIT-2A4 60mm IEC 225S, 225M (4, 6, 8 pole) ; IEC 250M (2 pole)
SGR-65-UKIT SGR-65-UKIT-2A4 65mm IEC 250M (4, 6, 8 pole); IEC 280M, 280S, 315S, 315M,315L (2 pole)
SGR-70-UKIT SGR-70-UKIT-2A4 70mm
SGR-75-UKIT SGR-75-UKIT-2A4 75mm IEC 280S, 280M (4, 6, 8 pole); IEC 355M, 355L (2 pole)
SGR-80-UKIT SGR-80-UKIT-2A4 80mm IEC 315S, 315M, 315L (4, 6, 8 pole)
SGR-95-UKIT SGR-95-UKIT-2A4 95mm IEC 335L, 335M, 355L, 355M (4, 6, 8, 10 pole)

Patented Technology
Solid Ring, Split Ring, and Bolt Through Mounting Dimensions in inches
Solid Ring with Split Ring* with Solid Ring Split Ring* Bolt Through* Min. Shaft Max. Shaft Outside Thickness
Conductive Epoxy Conductive Epoxy Catalog Number Catalog Number Catalog Number Diameter Diameter Diameter Max
SGR-6.9-0AW SGR-6.9-0A4W SGR-6.9-1 SGR-6.9-1A4 SGR-6.9-3FH 0.311 0.355 1.60 0.295

*Custom Part-No Return *Custom Part-No Return *Custom Part-No Return

Patented Technology
Solid Ring with Split Ring* with Solid Ring Split Ring* Bolt Through* Min. Shaft Max. Shaft Outside Thickness
Conductive Epoxy Conductive Epoxy Catalog Number Catalog Number Catalog Number Diameter Diameter Diameter Max

*Custom Part-No Return *Custom Part-No Return *Custom Part-No Return

Patented Technology
AEGIS® SGR - Press Fit Mounting Dimensions in inches
SGR OD Bore SGR OD Bore

Catalog Min.shaft Max.shaft Thickness Min.shaft Max.shaft Thickness
Tolerance Tolerance Catalog Number Tolerance Tolerance
Number diameter diameter Max diameter diameter Max
+0/-0.001 +0.001/-0 +0/-0.001 +0.001/-0
SGR-6.9-0A6 0.311 0.355 1.580 0.295 1.576 SGR-79.9-0A6 3.186 3.230 4.080 0.295 4.076
SGR- 8.0-0A6 0.356 0.395 1.580 0.295 1.576 SGR-81.1-0A6 3.231 3.270 4.080 0.295 4.076
SGR-9.0-0A6 0.396 0.435 1.580 0.295 1.576 SGR-82.1-0A6 3.271 3.310 4.080 0.295 4.076
SGR-10.1-0A6 0.436 0.480 1.580 0.295 1.576 SGR-83.1-0A6 3.311 3.355 4.080 0.295 4.076
SGR-11.2-0A6 0.481 0.520 1.580 0.295 1.576 SGR-84.2-0A6 3.356 3.395 4.080 0.295 4.076
SGR-12.2-0A6 0.521 0.560 1.580 0.295 1.576 SGR-85.2-0A6 3.396 3.435 4.580 0.295 4.576
SGR-13.2-0A6 0.561 0.605 1.580 0.295 1.576 SGR-86.3-0A6 3.436 3.480 4.580 0.295 4.576
SGR-14.4-0A6 0.606 0.645 1.580 0.295 1.576 SGR-87.4-0A6 3.481 3.520 4.580 0.295 4.576
SGR-15.4-0A6 0.646 0.685 2.080 0.295 2.076 SGR-88.4-0A6 3.521 3.560 4.580 0.295 4.576
SGR-16.4-0A6 0.686 0.730 2.080 0.295 2.076 SGR-89.4-0A6 3.561 3.605 4.580 0.295 4.576
SGR-17.6-0A6 0.731 0.774 2.080 0.295 2.076 SGR-90.6-0A6 3.606 3.645 4.580 0.295 4.576
SGR-18.7-0A6 0.775 0.815 2.080 0.295 2.076 SGR-91.6-0A6 3.646 3.685 4.580 0.295 4.576
SGR-19.7-0A6 0.816 0.855 2.080 0.295 2.076 SGR-92.6-0A6 3.686 3.730 4.580 0.295 4.576
SGR-20.7-0A6 0.856 0.895 2.080 0.295 2.076 SGR-93.8-0A6 3.731 3.770 4.580 0.295 4.576
SGR-21.7-0A6 0.896 0.935 2.080 0.295 2.076 SGR-94.8-0A6 3.771 3.810 4.580 0.295 4.576
SGR-22.8-0A6 0.936 0.980 2.080 0.295 2.076 SGR-95.8-0A6 3.811 3.855 4.580 0.295 4.576
SGR-23.9-0A6 0.981 1.020 2.080 0.295 2.076 SGR-96.9-0A6 3.856 3.895 4.580 0.295 4.576
SGR-24.9-0A6 1.021 1.060 2.080 0.295 2.076 SGR-97.9-0A6 3.896 3.935 5.080 0.295 5.076
SGR-25.9-0A6 1.061 1.105 2.080 0.295 2.076 SGR-99.0-0A6 3.936 3.980 5.080 0.295 5.076
SGR-27.1-0A6 1.106 1.145 2.080 0.295 2.076 SGR-100.1-0A6 3.981 4.020 5.080 0.295 5.076
SGR-28.1-0A6 1.146 1.185 2.080 0.295 2.076 SGR-101.1-0A6 4.021 4.060 5.080 0.295 5.076
SGR-29.1-0A6 1.186 1.230 2.080 0.295 2.076 SGR-102.1-0A6 4.061 4.105 5.080 0.295 5.076
SGR-30.3-0A6 1.231 1.270 2.080 0.295 2.076 SGR-103.3-0A6 4.106 4.145 5.080 0.295 5.076
SGR-31.3-0A6 1.271 1.310 2.080 0.295 2.076 SGR-104.3-0A6 4.146 4.185 5.080 0.295 5.076
SGR-32.3-0A6 1.311 1.355 2.080 0.295 2.076 SGR-105.3-0A6 4.186 4.230 5.080 0.295 5.076
SGR-33.4-0A6 1.356 1.395 2.080 0.295 2.076 SGR-106.5-0A6 4.231 4.270 5.080 0.295 5.076
SGR-34.4-0A6 1.396 1.435 2.660 0.295 2.656 SGR-107.5-0A6 4.271 4.310 5.080 0.295 5.076
SGR-35.5-0A6 1.436 1.480 2.660 0.295 2.656 SGR-108.5-0A6 4.311 4.355 5.080 0.295 5.076
SGR-36.6-0A6 1.481 1.520 2.660 0.295 2.656 SGR-109.6-0A6 4.356 4.395 5.080 0.295 5.076
SGR-37.6-0A6 1.521 1.560 2.660 0.295 2.656 SGR-110.6-0A6 4.396 4.435 5.580 0.295 5.576
SGR-38.6-0A6 1.561 1.605 2.660 0.295 2.656 SGR-111.7-0A6 4.436 4.480 5.580 0.295 5.576
SGR-39.8-0A6 1.606 1.645 2.660 0.295 2.656 SGR-112.8-0A6 4.481 4.520 5.580 0.295 5.576
SGR-40.8-0A6 1.646 1.685 2.660 0.295 2.656 SGR-113.8-0A6 4.521 4.560 5.580 0.295 5.576
SGR-41.8-0A6 1.686 1.730 2.660 0.295 2.656 SGR-114.8-0A6 4.561 4.605 5.580 0.295 5.576
SGR-43.0-0A6 1.731 1.770 2.660 0.295 2.656 SGR-116.0-0A6 4.606 4.645 5.580 0.295 5.576
SGR-44.0-0A6 1.771 1.810 2.660 0.295 2.656 SGR-117.0-0A6 4.646 4.685 5.580 0.295 5.576
SGR-45.0-0A6 1.811 1.855 2.660 0.295 2.656 SGR-118.0-0A6 4.686 4.730 5.580 0.295 5.576
SGR-46.1-0A6 1.856 1.895 2.660 0.295 2.656 SGR-119.2-0A6 4.731 4.770 5.580 0.295 5.576
SGR-47.1-0A6 1.896 1.935 2.660 0.295 2.656 SGR-120.2-0A6 4.771 4.810 5.580 0.295 5.576
SGR-48.2-0A6 1.936 1.980 2.660 0.295 2.656 SGR-121.2-0A6 4.811 4.855 5.580 0.295 5.576
SGR-49.3-0A6 1.981 2.020 2.660 0.295 2.656 SGR-122.3-0A6 4.856 4.895 5.580 0.295 5.576
SGR-50.3-0A6 2.021 2.060 3.080 0.295 3.076 SGR-123.3-0A6 4.896 4.935 6.080 0.295 6.076
SGR-51.3-0A6 2.061 2.105 3.080 0.295 3.076 SGR-124.4-0A6 4.936 4.980 6.080 0.295 6.076
SGR-52.5-0A6 2.106 2.145 3.080 0.295 3.076 SGR-125.5-0A6 4.981 5.020 6.080 0.295 6.076
SGR-53.5-0A6 2.146 2.185 3.080 0.295 3.076 SGR-126.5-0A6 5.021 5.060 6.080 0.295 6.076
SGR-54.5-0A6 2.186 2.230 3.080 0.295 3.076 SGR-127.5-0A6 5.061 5.105 6.080 0.295 6.076
SGR-55.7-0A6 2.231 2.270 3.080 0.295 3.076 SGR-128.7-0A6 5.106 5.145 6.080 0.295 6.076
SGR-56.7-0A6 2.271 2.310 3.080 0.295 3.076 SGR-129.7-0A6 5.146 5.185 6.080 0.295 6.076
SGR-57.7-0A6 2.311 2.355 3.080 0.295 3.076 SGR-130.7-0A6 5.186 5.230 6.080 0.295 6.076
SGR-58.8-0A6 2.356 2.395 3.080 0.295 3.076 SGR-131.9-0A6 5.231 5.270 6.080 0.295 6.076
SGR-59.8-0A6 2.396 2.435 3.580 0.295 3.576 SGR-132.9-0A6 5.271 5.310 6.080 0.295 6.076
SGR-60.9-0A6 2.436 2.480 3.580 0.295 3.576 SGR-133.9-0A6 5.311 5.355 6.080 0.295 6.076
SGR-62.0-0A6 2.481 2.520 3.580 0.295 3.576 SGR-135.0-0A6 5.356 5.395 6.080 0.295 6.076
SGR-63.0-0A6 2.521 2.560 3.580 0.295 3.576 SGR-136.0-0A6 5.396 5.435 6.580 0.295 6.576
SGR-64.0-0A6 2.561 2.605 3.580 0.295 3.576 SGR-137.1-0A6 5.436 5.480 6.580 0.295 6.576
SGR-65.2-0A6 2.606 2.645 3.580 0.295 3.576 SGR-138.2-0A6 5.481 5.520 6.580 0.295 6.576
SGR-66.2-0A6 2.646 2.685 3.580 0.295 3.576 SGR-139.2-0A6 5.521 5.560 6.580 0.295 6.576
SGR-67.2-0A6 2.686 2.730 3.580 0.295 3.576 SGR-140.2-0A6 5.561 5.605 6.580 0.295 6.576
SGR-68.4-0A6 2.731 2.770 3.580 0.295 3.576 SGR-141.4-0A6 5.606 5.645 6.580 0.295 6.576
SGR-69.4-0A6 2.771 2.810 3.580 0.295 3.576 SGR-142.4-0A6 5.646 5.685 6.580 0.295 6.576
SGR-70.4-0A6 2.811 2.855 3.580 0.295 3.576 SGR-143.4-0A6 5.686 5.730 6.580 0.295 6.576
SGR-71.5-0A6 2.856 2.895 3.580 0.295 3.576 SGR-144.6-0A6 5.731 5.770 6.580 0.295 6.576
SGR-72.5-0A6 2.896 2.935 4.080 0.295 4.076 SGR-145.6-0A6 5.771 5.810 6.580 0.295 6.576
SGR-73.6-0A6 2.936 2.980 4.080 0.295 4.076 SGR-146.6-0A6 5.811 5.855 6.580 0.295 6.576
SGR-74.7-0A6 2.981 3.020 4.080 0.295 4.076 SGR-147.7-0A6 5.856 5.895 6.580 0.295 6.576
SGR-75.7-0A6 3.021 3.060 4.080 0.295 4.076 SGR-148.7-0A6 5.896 5.935 7.080 0.295 7.076
SGR-76.7-0A6 3.061 3.105 4.080 0.295 4.076 SGR-149.8-0A6 5.936 5.980 7.080 0.295 7.076
SGR-77.9-0A6 3.106 3.145 4.080 0.295 4.076 SGR-150.9-0A6 5.981 6.020 7.080 0.295 7.076
SGR-78.9-0A6 3.146 3.185 4.080 0.295 4.076
Custom Part-No Return Custom Part-No Return

Patented Technology
Kits with Aluminum Plates and Spacers
Includes AEGIS® SGR Bearing Protection Ring and all mounting hardware
NEMA Motors NEMA Motors Motor Shaft SOLID
NEMA Frame Plate OD
Solid Split Diameter “u”
SGR-0.625-NEMA SGR-0.625-NEMA-1A4 0.625” 56 3.75”
SGR-0.875-NEMA SGR-0.875-NEMA-1A4 0.875” 56HZ, 143T, 145T 5.60”
SGR-1.125-NEMA SGR-1.125-NEMA-1A4 1.125” 182T, 184T 5.60”
SGR-1.375-NEMA SGR-1.375-NEMA-1A4 1.375” 213T, 215T 5.60”
SGR-1.625-NEMA SGR-1.625-NEMA-1A4 1.625” 254T, 256T, 284TS, 286TS 6.30”
SGR-1.875-NEMA SGR-1.875-NEMA-1A4 1.875” 284T, 286T, 324TS, 326TS, 364TS, 365TS 6.30” 1 AEGIS® SGR
1 mounting plate
SGR-2.125-NEMA SGR-2.125-NEMA-1A4 2.125” 324T, 326T, 404TS, 405TS 6.60”
3 screws (inches or metric)
SGR-2.375-NEMA SGR-2.375-NEMA-1A4 2.375” 364T, 365T, 444TS, 445TS, 447TS, 449TS 6.60” 3 washers
SGR-2.875-NEMA SGR-2.875-NEMA-1A4 2.875” 404T, 405T 7.30” 3 lock washers
3 spacers*
SGR-3.375-NEMA SGR-3.375-NEMA-1A4 3.375” 444T, 445T, 447T, 449T 7.60”
SPLIT
IEC Motors IEC Motors IEC Shaft

IEC Frame Plate OD
Solid Split Diameter
SGR-19-IEC SGR-19-IEC-2A4 19mm IEC 80 (2, 4, 6, 8 pole) 142mm
SGR-24-IEC SGR-24-IEC-2A4 24mm IEC 90S, 90L (2, 4, 6, 8 pole) 142mm
SGR-28-IEC SGR-28-IEC-2A4 28mm IEC 100L, 112M (2, 4, 6, 8 pole) 142mm
SGR-38-IEC SGR-38-IEC-2A4 38mm IEC 132S, 132M (2, 4, 6, 8 pole) 160mm 1 AEGIS® Split Ring SGR
SGR-42-IEC SGR-42-IEC-2A4 42mm IEC 160M, 160L (2, 4, 6, 8 pole) 160mm 1 split mounting plate
3 screws (inches or metric)
SGR-48-IEC SGR-48-IEC-2A4 48mm IEC 180M, 180L (2, 4, 6, 8 pole) 160mm
3 washers
SGR-55-IEC SGR-55-IEC-2A4 55mm IEC 200L (2, 4, 6, 8 pole); IEC 225S, 225M (2 pole) 168mm 3 lock washers
SGR-60-IEC SGR-60-IEC-2A4 60mm IEC 225S, 225M (4, 6, 8 pole) ; IEC 250M (2 pole) 168mm
3 spacers*
SGR-65-IEC SGR-65-IEC-2A4 65mm IEC 250M (4, 6, 8 pole); IEC 280M, 280S, 315S, 315M, 315L (2 pole) 185mm
Each kit includes 3 spacer lengths: 1/4”,
SGR-75-IEC SGR-75-IEC-2A4 75mm IEC 280S, 280M (4, 6, 8 pole); IEC 355M, 355L (2 pole) 193mm 1/2”, and 1” for NEMA kits and 7mm,
17mm, and 27mm for IEC kits.
SGR-80-IEC SGR-80-IEC-2A4 80mm IEC 315S, 315M, 315L (4, 6, 8 pole) 193mm
Mounting Plates with Hardware(no SGR)

On occasions when the
shaft diameter is not one Fits any SGR with OD Fits any SGR with OD
of the kitted NEMA sizes, English Hardware as specified Metric Hardware as specified
select the correct SGR for SGR OD: SGR OD:
the shaft diameter, note the
SGR OD, then go to the chart SGR-M40-1A4 1.60” (40.6mm) SGR-M40-2A4 1.60” (40.6mm)
to the right to determine the SGR-M53-1A4 2.10” (53.3mm) SGR-M53-2A4 2.10” (53.3mm)
matching Mounting Plate.
SGR-M68-1A4 2.68” (68.1mm) SGR-M68-2A4 2.68” (68.1mm)
Plate can be used with a
solid or split ring SGR. SGR-M78-1A4 3.10” (78.8mm) SGR-M78-2A4 3.10” (78.8mm)
SGR-M91-1A4 3.60” (91.4mm) SGR-M91-2A4 3.60” (91.4mm)
SGR-M104-1A4 4.10” (104.1mm) SGR-M104-2A4 4.10” (104.1mm)
SGR-M116-1A4 4.60” (116.8mm) SGR-M116-2A4 4.60” (116.8mm)
SGR-M129-1A4 5.10” (129.5mm) SGR-M129-2A4 5.10” (129.5mm)
SGR-M142-1A4 5.60” (142.2mm) SGR-M142-2A4 5.60” (142.2mm)
SGR-M154-1A4 6.10” (154.9mm) SGR-M154-2A4 6.10” (154.9mm)
SGR-M167-1A4 6.60” (167.6mm) SGR-M167-2A4 6.60” (167.6mm)
SGR-M180-1A4 7.10” (180.3mm) SGR-M180-2A4 7.10” (180.3mm)
Kit includes (1) mounting plate, Kit includes (1) mounting plate,
(3) 1/4” spacers with screws and washers (3) 7mm spacers with screws and washers
(3) 1/2” spacers with screws and washers (3) 17mm spacers with screws and washers
SGR sold separately
(3) 1” spacers with screws and washers (3) 27mm spacers with screws and washers

Patented Technology
Custom Large SGR, iPRO, WTG
AEGIS® Large SGR

Shaft diameter 6.03” to 15.748”
For Motors up to and including 500hp (Low Voltage-up to 600 volts AC)
Outside Diameter: Shaft Diameter + 1.50”
Drawings available upon request
Solid and Split Ring design

Includes two mounting hardware options:
Bracket Mounting: (6) Standard mounting brackets, (6) 6-32 x 1/4” SHCS with star washers
Bolt Through Mounting: (4) 8-32 x 5/8” SHCS with lock washers
AEGIS® iPROSL
Shaft Diameter 3.00” to 30.00”
High Current Bearing Protection for Large Motors over 500hp and Generators
(Medium Voltage-greater than 600 volts AC)
Outside Diameter: Slim Line Version-Shaft Diameter + 1.86”

6 rows of fiber
Includes bolt through mounting hardware: (4) 8-32 x 1” SHCS with lock washers
Custom Brackets available upon request
Ships with CS015 Colloidal Silver Shaft Coating
AEGIS® WTGSL Wind Turbine Grounding

Shaft Diameter 3.00” to 15.75”
High Current Bearing Protection for Wind Turbine Generators
Outside Diameter: Shaft Diameter + 1.86”

6 rows of fiber
Includes bolt through mounting hardware: (4) 8-32 x 1” SHCS with lock washers
Custom Brackets available upon request
Ships with CS015 Colloidal Silver Shaft Coating

Patented Technology
AEGIS® Accessories
AEGIS® SVP Shaft Voltage Probe Kits
Conductive Microfiber tips for use with Fluke 190 Series II ScopeMeter®
For the first time you can easily and more accurately measure the voltage on a rotating shaft. The AEGIS® SVP
SVP-KIT-3000MB Shaft Voltage Probe’s unique design of high density conductive microfibers ensures continuous contact with
the rotating shaft. Used with the Fluke 190 Series II ScopeMeter, you can determine if your motor is subject to
potentially damaging bearing currents. Visit our website for a complete part list.
AEGIS® SVP Shaft Voltage Probe Kits

Catalog Number Includes:
3 SVP tips, probe holder with two piece extension rod (total
SVP-KIT-3000MB length of probe holder with extension rod is 18 inches), AEGIS®
Grounding Simulator, and magnetic base.
SVP-KIT-3000
3 SVP tips, probe holder with two piece extension rod, and AEGIS®
SVP-KIT-3000
Grounding Simulator.
SVP-TIP-3000 3 SVP replacement tips only
Fits Fluke VPS410 Voltage Probe. For other probe styles, see website.
SVP-TIP-3000
Installation: Pull off the hook clip from the voltage probe. Install the SVP tip over the voltage probe
tip until seated against the probe shoulder. Secure with plastic screw. Do not over tighten screw.
10:1 oscilloscope probe not included

Magnetic base not sold separately
AEGIS® Colloidal Silver Shaft Coating

Catalog Number Coverage:
CS015 20-25 applications based on a 3” shaft diameter
Used to improve the conductivity of the steel shaft surface. Apply to any VFD driven motor shaft
prior to installing the AEGIS® Bearing Protection Ring.
Note: Shelf life is 6 months
AEGIS® Conductive Epoxy

Catalog Number Coverage:
EP2400 2-3 applications
Used to install the AEGIS® Bearing Protection Ring without drilling and tapping into the motor end
bell.
Note: Shelf life is 9 months

Patented Technology
Engineering Specification
Motors Controlled by PWM Drives (VFD)

Electrical Bearing Damage Protection
Engineering Specification:
Construction Specification Institute Section 23 05 13

MOTORS 23 05 13
2.1 MOTORS
A. General Requirements:
1. All motors operated on variable frequency drives shall be equipped with a maintenance
free, conductive micro fiber, shaft grounding ring with a minimum of two rows of circumfer-
ential micro fibers to discharge electrical shaft currents within the motor and/or its bearings.
2. Application Note: Motors up to 100HP shall be provided with a minimum of one shaft
grounding ring installed either on the drive end or non-drive end. Motors over 100HP shall
be provided with an insulated bearing on the non-drive end and a shaft grounding ring on
the drive end of the motor. Grounding rings shall be provided and installed by the motor
pump manufacturer or contractor and shall be installed in accordance with the manufac-
turer’s recommendations.
Recommended part: AEGIS® SGR Bearing Protection Ring
Recommended source: Electro Static Technology-ITW

Manufacturer of AEGIS® Bearing Protection Ring
Ph: 207.998.5140 | [email protected] | www.est-aegis.com
Detail Sheet
.375 ±.010
.1875 ±.010
Shaft Grounding Ring
(.695)
Motor
Max Shaft
End Shoulder Ø
Bracket Shaft Ø + .500"
Shaft
Shaft Shoulder
Slinger / Seal
Max Slinger/Seal OD
Or Casting Boss =
Shaft Ø + 1.0"
Shaft Grounding Ring AEGIS uKIT
Web Resources: For Specifying Engineer

www.est-aegis.com/specs.htm Resource Page
WARRANTY: Units are guaranteed for one year from date of purchase against defective materials and workmanship. Replacement will be made
except for defects caused by abnormal use or mishandling. All statements and technical information contained herein, or presented by the
manufacturer or his representative are rendered in good faith. User must assume responsibility to determine suitability of the product for
intended use. The manufacturer shall not be liable for any injury, loss or damage, direct or consequential arising out of the use, or attempt to use
the product.
The following patents apply: 8199453, 8169766, 7193836, 7136271, 7528513, 7339777, and other patents pending.

Patented Technology
Conversion Table - Inches - Metric
Min.shaft Max.shaft Min.shaft Max.shaft Min.shaft Max.shaft Min.shaft Max.shaft

Catalog
diameter diameter diameter diameter
Catalog
diameter diameter diameter diameter Fraction, Decimal and Millimeter
Number Number
inches inches mm mm inches inches mm mm
Equivalents
SGR-6.9-*** 0.311 0.355 7.9 9.0 SGR-79.9-*** 3.186 3.230 81.0 82.0
SGR-8.0-*** 0.356 0.395 9.1 10.0 SGR-81.1-*** 3.231 3.270 82.1 83.1
Fraction Decimal mm
SGR-9.0-*** 0.396 0.435 10.1 11.0 SGR-82.1-*** 3.271 3.310 83.2 84.1
SGR-10.1-*** 0.436 0.480 11.1 12.2 SGR-83.1-*** 3.311 3.355 84.2 85.2
1/64 .0156 0.396
SGR-11.2-*** 0.481 0.520 12.3 13.2 SGR-84.2-*** 3.356 3.395 85.3 86.2
1/32 .0312 0.793
SGR-12.2-*** 0.521 0.560 13.3 14.2 SGR-85.2-*** 3.396 3.435 86.3 87.2
3/64 .0468 1.190
SGR-13.2-*** 0.561 0.605 14.3 15.4 SGR-86.3-*** 3.436 3.480 87.3 88.4
1/16 .0625 1.587
SGR-14.4-*** 0.606 0.645 15.5 16.4 SGR-87.4-*** 3.481 3.520 88.5 89.4
5/64 .0781 1.984
SGR-15.4-*** 0.646 0.685 16.5 17.4 SGR-88.4-*** 3.521 3.560 89.5 90.4
3/32 .0937 2.381
SGR-16.4-*** 0.686 0.730 17.5 18.5 SGR-89.4-*** 3.561 3.605 90.5 91.6
7/64 .1093 2.778
SGR-17.6-*** 0.731 0.774 18.6 19.7 SGR-90.6-*** 3.606 3.645 91.7 92.6
1/8 .1250 3.175
SGR-18.7-*** 0.775 0.815 19.8 20.7 SGR-91.6-*** 3.646 3.685 92.7 93.6
9/64 .1406 3.571
SGR-19.7-*** 0.816 0.855 20.8 21.7 SGR-92.6-*** 3.686 3.730 93.7 94.7
5/32 .1562 3.968
SGR-20.7-*** 0.856 0.895 21.8 22.7 SGR-93.8-*** 3.731 3.770 94.8 95.8
11/64 .1718 4.365
SGR-21.7-*** 0.896 0.935 22.8 23.7 SGR-94.8-*** 3.771 3.810 95.9 96.8
3/16 .1875 4.762
SGR-22.8-*** 0.936 0.980 23.8 24.9 SGR-95.8-*** 3.811 3.855 96.9 97.9
13/64 .2031 5.159
SGR-23.9-*** 0.981 1.020 25.0 25.9 SGR-96.9-*** 3.856 3.895 98.0 98.9
7/32 .2187 5.556
SGR-24.9-*** 1.021 1.060 26.0 26.9 SGR-97.9-*** 3.896 3.935 99.0 99.9
15/64 .2343 5.953
SGR-25.9-*** 1.061 1.105 27.0 28.1 SGR-99.0-*** 3.936 3.980 100.0 101.1
1/4 .2500 6.350
SGR-27.1-*** 1.106 1.145 28.2 29.1 SGR-100.1-*** 3.981 4.020 101.2 102.1
17/64 .2656 6.746
SGR-28.1-*** 1.146 1.185 29.2 30.1 SGR-101.1-*** 4.021 4.060 102.2 103.1
9/32 .2812 7.143
SGR-29.1-*** 1.186 1.230 30.2 31.2 SGR-102.1-*** 4.061 4.105 103.2 104.3
19/64 .2968 7.540
SGR-30.3-*** 1.231 1.270 31.3 32.3 SGR-103.3-*** 4.106 4.145 104.4 105.3
5/16 .3125 7.937
SGR-31.3-*** 1.271 1.310 32.4 33.3 SGR-104.3-*** 4.146 4.185 105.4 106.3
21/64 .3281 8.334
SGR-32.3-*** 1.311 1.355 33.4 34.4 SGR-105.3-*** 4.186 4.230 106.4 107.4
11/32 .3437 8.731
SGR-33.4-*** 1.356 1.395 34.5 35.4 SGR-106.5-*** 4.231 4.270 107.5 108.5
23/64 .3593 9.128
SGR-34.4-*** 1.396 1.435 35.5 36.4 SGR-107.5-*** 4.271 4.310 108.6 109.5
3/8 .3750 9.525
SGR-35.5-*** 1.436 1.480 36.5 37.6 SGR-108.5-*** 4.311 4.355 109.6 110.6
25/64 .3906 9.921
SGR-36.6-*** 1.481 1.520 37.7 38.6 SGR-109.6-*** 4.356 4.395 110.7 111.6
13/32 .4062 10.318
SGR-37.6-*** 1.521 1.560 38.7 39.6 SGR-110.6-*** 4.396 4.435 111.7 112.6
27/64 .4218 10.715
SGR-38.6-*** 1.561 1.605 39.7 40.8 SGR-111.7-*** 4.436 4.480 112.7 113.8
7/16 .4375 11.112
SGR-39.8-*** 1.606 1.645 40.9 41.8 SGR-112.8-*** 4.481 4.520 113.9 114.8
29/64 .4531 11.509
SGR-40.8-*** 1.646 1.685 41.9 42.8 SGR-113.8-*** 4.521 4.560 114.9 115.8
15/32 .4687 11.906
SGR-41.8-*** 1.686 1.730 42.9 43.9 SGR-114.8-*** 4.561 4.605 115.9 117.0
31/64 .4843 12.303
SGR-43.0-*** 1.731 1.770 44.0 45.0 SGR-116.0-*** 4.606 4.645 117.1 118.0
1/2 .5000 12.700
SGR-44.0-*** 1.771 1.810 45.1 46.0 SGR-117.0-*** 4.646 4.685 118.1 119.0
33/64 .5156 13.096
SGR-45.0-*** 1.811 1.855 46.1 47.1 SGR-118.0-*** 4.686 4.730 119.1 120.1
17/32 .5312 13.493
SGR-46.1-*** 1.856 1.895 47.2 48.1 SGR-119.2-*** 4.731 4.770 120.2 121.2
35/64 .5468 13.890
SGR-47.1-*** 1.896 1.935 48.2 49.1 SGR-120.2-*** 4.771 4.810 121.3 122.2
9/16 .5625 14.287
SGR-48.2-*** 1.936 1.980 49.2 50.3 SGR-121.2-*** 4.811 4.855 122.3 123.3
37/64 .5781 14.684
SGR-49.3-*** 1.981 2.020 50.4 51.3 SGR-122.3-*** 4.856 4.895 123.4 124.3
19/32 .5937 15.081
SGR-50.3-*** 2.021 2.060 51.4 52.3 SGR-123.3-*** 4.896 4.935 124.4 125.3
39/64 .6093 15.478
SGR-51.3-*** 2.061 2.105 52.4 53.5 SGR-124.4-*** 4.936 4.980 125.4 126.5
5/8 .6250 15.875
SGR-52.5-*** 2.106 2.145 53.6 54.5 SGR-125.5-*** 4.981 5.020 126.6 127.5
41/64 .6406 16.271
SGR-53.5-*** 2.146 2.185 54.6 55.5 SGR-126.5-*** 5.021 5.060 127.6 128.5
21/32 .6562 16.668
SGR-54.5-*** 2.186 2.230 55.6 56.6 SGR-127.5-*** 5.061 5.105 128.6 129.7
43/64 .6718 17.065
SGR-55.7-*** 2.231 2.270 56.7 57.7 SGR-128.7-*** 5.106 5.145 129.8 130.7
11/16 .6875 17.462
SGR-56.7-*** 2.271 2.310 57.8 58.7 SGR-129.7-*** 5.146 5.185 130.8 131.7
45/64 .7031 17.859
SGR-57.7-*** 2.311 2.355 58.8 59.8 SGR-130.7-*** 5.186 5.230 131.8 132.8
23/32 .7187 18.256
SGR-58.8-*** 2.356 2.395 59.9 60.8 SGR-131.9-*** 5.231 5.270 132.9 133.9
47/64 .7343 18.653
SGR-59.8-*** 2.396 2.435 60.9 61.8 SGR-132.9-*** 5.271 5.310 134.0 134.9
3/4 .7500 19.050
SGR-60.9-*** 2.436 2.480 61.9 63.0 SGR-133.9-*** 5.311 5.355 135.0 136.0
49/64 .7656 19.446
SGR-62.0-*** 2.481 2.520 63.1 64.0 SGR-135.0-*** 5.356 5.395 136.1 137.0
25/32 .7812 19.843
SGR-63.0-*** 2.521 2.560 64.1 65.0 SGR-136.0-*** 5.396 5.435 137.1 138.0
51/64 .7968 20.240
SGR-64.0-*** 2.561 2.605 65.1 66.2 SGR-137.1-*** 5.436 5.480 138.1 139.2
13/16 .8125 20.637
SGR-65.2-*** 2.606 2.645 66.3 67.2 SGR-138.2-*** 5.481 5.520 139.3 140.2
53/64 .8281 21.034
SGR-66.2-*** 2.646 2.685 67.3 68.2 SGR-139.2-*** 5.521 5.560 140.3 141.2
27/32 .8437 21.431
SGR-67.2-*** 2.686 2.730 68.3 69.3 SGR-140.2-*** 5.561 5.605 141.3 142.4
55/64 .8593 21.828
SGR-68.4-*** 2.731 2.770 69.4 70.4 SGR-141.4-*** 5.606 5.645 142.5 143.4
7/8 .8750 22.225
SGR-69.4-*** 2.771 2.810 70.5 71.4 SGR-142.4-*** 5.646 5.685 143.5 144.4
57/64 .8906 22.621
SGR-70.4-*** 2.811 2.855 71.5 72.5 SGR-143.4-*** 5.686 5.730 144.5 145.5
29/32 .9062 23.018
SGR-71.5-*** 2.856 2.895 72.6 73.5 SGR-144.6-*** 5.731 5.770 145.6 146.6
59/64 .9218 23.415
SGR-72.5-*** 2.896 2.935 73.6 74.5 SGR-145.6-*** 5.771 5.810 146.7 147.6
15/16 .9375 23.812
SGR-73.6-*** 2.936 2.980 74.6 75.7 SGR-146.6-*** 5.811 5.855 147.7 148.7
61/64 .9531 24.209
SGR-74.7-*** 2.981 3.020 75.8 76.7 SGR-147.7-*** 5.856 5.895 148.8 149.7
31/32 .9687 24.606
SGR-75.7-*** 3.021 3.060 76.8 77.7 SGR-148.7-*** 5.896 5.935 149.8 150.7
63/64 .9843 25.003
SGR-76.7-*** 3.061 3.105 77.8 78.9 SGR-149.8-*** 5.936 5.980 150.8 151.9
1 1.0000 25.400
SGR-77.9-*** 3.106 3.145 79.0 79.9 SGR-150.9-*** 5.981 6.020 152.0 152.9
SGR-78.9-*** 3.146 3.185 80.0 80.9 *** PN suffix differs depending on mounting option

Patented Technology
Electro Static Technology
An ITW Company
® SGR
31 Winterbrook Road
Mechanic Falls, ME 04256 USA
BEARING PROTECTION RING
Ph: 207-998-5140
www.est-aegis.com
Use of the EASA logo expresses

membership only and not endorsement
by EASA of the content in this handbook.

Aegis® Shaft Grounding Ring Bearing Protection Handbook: Edition 2

Uploaded by

Copyright:

Available Formats

Aegis® Shaft Grounding Ring Bearing Protection Handbook: Edition 2

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aegis® Shaft Grounding Ring Bearing Protection Handbook: Edition 2

Uploaded by

Copyright:

Available Formats

® SGR

BEARING PROTECTION RING

AEGIS® SHAFT GROUNDING RING

© 2013 Electro Static Technology, An ITW Company, All rights reserved.

New Motor and Repair Standards 5

About VFD Induced Shaft Voltages & Bearing Currents 6-9

Bearing Frosting & Fluting 10

Cutting and Inspecting a Bearing 11-12

AEGIS® Shaft Grounding Best Practices 13-21

TO RECEIVE HANDBOOK UPDATES:

© 2013 Electro Static Technology www.est-aegis.com AEGIS® Handbook | 3

ANSI/EASA Standard AR100-2010, Section 2, Mechanical Repair: 2.2 Bearings

Electrical Motor Repair, Bearing Inspection, and Testing Services:

Best Practices and Service Portfolio:

G ive advice on preventing bearing failures for VFD driven motors

Inspect bearings for signs of electrical discharge machining (EDM) damage

S atisfy the customer with superior repair services

EDM Pit Frosted Bearing Race Fluted Outer Bearing Race

4 | AEGIS® Handbook www.est-aegis.com © 2013 Electro Static Technology

Be the leader in your industry!

ANSI/EASA Standard AR100-2010 and Shaft Grounding Best practices: Going

© 2013 Electro Static Technology www.est-aegis.com AEGIS® Handbook | 5

Electric Motors Operating on Line Voltage

Electric Motors Operated by Variable Frequency Drives (VFD)

Bearing protection needed to mitigate electrical discharge machining

6 | AEGIS® Handbook www.est-aegis.com © 2013 Electro Static Technology

There are two primary sources of bearing currents in VFD driven

Bearing Current A: is a capacitive induced shaft voltage that

Best Practice: Ground the motor shaft with the AEGIS®

An Electric Motor works like a Capacitor

• Voltages are measurable with a Fluke 190 series

Portion of charge returned through ground wires

Probe Tip. Rotor

Voltage arcs through the bearing

• Bearings degrade, resulting in increased friction and

• Bearing lubrication/grease deteriorates, is burnt and Stator

• Potential for costly unplanned downtime VFD Balanced

High Frequency Circulating Currents

Bearing Current B: High frequency circulating currents may

a. Circulate through the motor bearings, shaft to frame.

Best Practice: Interrupting the high frequency circulating

8 | AEGIS® Handbook www.est-aegis.com © 2013 Electro Static Technology

A third source of bearing currents are circulating currents from

Total Qualitative Bearing Currents

Best Practice: Interrupting the circulating current is the best

© 2013 Electro Static Technology www.est-aegis.com AEGIS® Handbook | 9

EDM Electrical Discharge Machining

Because of the high-speed switching frequencies in PWM inverters, variable

Once these voltages reach a level sufficient to overcome the dielectric

10 | AEGIS® Handbook www.est-aegis.com © 2013 Electro Static Technology

Cutting and inspecting every bearing in motors that come in for

2. Cut the outer race into halves.

3. Inspect the grease and contamination in the bearing.

© 2013 Electro Static Technology www.est-aegis.com AEGIS® Handbook | 11

Burnt bearing grease is blackened and often times contaminated

New bearing grease is available in many colors.

4. Clean the bearing’s components using a degreaser or solvent.

5. Inspect for evidence of Electrical Discharge Machining (EDM): EDM

7. Fluting Damage: Identified by a distinctive washboard pattern. Fluting

Medium Voltage Motors: AEGIS® iPRO Ground