Scribd
Upload
69 views6 pages

AOC Two Port Network Lab Report (Template)

This laboratory report details an experiment to analyze two-port networks. Measurements were taken of currents and voltages in T-network and π-network configurations under varying voltage supplies. The results were used to calculate the z-parameters for the T-network and y-parameters for the π-network. These calculated values were then compared to theoretical parameters derived from the component resistances to verify the two-port models. Discussion focuses on comparing measurement and calculation results and factors affecting outcomes.

Uploaded by

Bader Al-Sabri
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
69 views6 pages

AOC Two Port Network Lab Report (Template)

This laboratory report details an experiment to analyze two-port networks. Measurements were taken of currents and voltages in T-network and π-network configurations under varying voltage supplies. The results were used to calculate the z-parameters for the T-network and y-parameters for the π-network. These calculated values were then compared to theoretical parameters derived from the component resistances to verify the two-port models. Discussion focuses on comparing measurement and calculation results and factors affecting outcomes.

Uploaded by

Bader Al-Sabri
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

ASIA PACIFIC UNIVERSITY

TECHNOLOGY & INNOVATION

EE001-3-1 ANALYSIS OF CIRCUITS


LABORATORY REPORT

TITLE TWO PORT NETWORK ANALYSIS

NAME & STUDENT ID

INTAKE

LECTURER

DATE
TABLE OF CONTENTS
LIST OF FIGURES ..................................................................................................................2
LIST OF TABLES ....................................................................................................................2
INTRODUCTION .....................................................................................................................3
EQUIPMENT LIST ..................................................................................................................3
PROCEDURE ...........................................................................................................................3
T-Network Verification (z-parameter) .................................................................................3
𝝅-Network Verification (y-parameter) .................................................................................4
RESULT ....................................................................................................................................5
DISCUSSION ............................................................................................................................6
CONCLUSION .........................................................................................................................6
REFERENCES ..........................................................................................................................6
APPENDIX ................................................................................................................................6

LIST OF FIGURES

Figure 1: T-Network Verification (z-parameter) Circuit 1 ...........................................................3


Figure 2: T-Network Verification (z-parameter) Circuit 2 ...........................................................4
Figure 3: π-Network Verification (y-parameter) Circuit 1 ............................................................4
Figure 4: π-Network Verification (y-parameter) Circuit 2 ............................................................5

LIST OF TABLES

Table 1: T-Network Verification Result ......................................................................................5


Table 2: π-Network Verification Result .......................................................................................5
Table 3: Parameters Calculation ..................................................................................................6

2
INTRODUCTION
Write background introduction in this section

OBJECTIVES

After performing this experiment, students should be able to:

1. Understand the concept of two port network.


2. Verify the parameters of a two port network using experimental result.
3. Relate the experimental result with the theoretical calculated values.

EQUIPMENT LIST
1. Power supply
2. Ammeter
3. Voltmeter
4. Resistors with different values (𝑅1 = 1000𝛺, 𝑅2 = 2000𝛺, 𝑅3 = 3000𝛺)

PROCEDURE
T-Network Verification (z-parameter)
1. T-Network was constructed as shown in Figure 1.

Figure 1: T-Network Verification (z-parameter) Circuit 1

2. Power supply was set to 5V.


3. Value of 𝐼1 and 𝑉2 were recorded in Result Table.
4. Step 2 and Step 3 were repeated with power supply of 10𝑉 and 15𝑉.
5. T-Network was constructed as shown in Figure 2.

3
Figure 2: T-Network Verification (z-parameter) Circuit 2

6. Power supply was set to 5𝑉.


7. Value of 𝐼2 and 𝑉1 were recorded in Result Table.
8. Step 2 and Step 3 were repeated with power supply of 10𝑉 and 15𝑉.
𝝅-Network Verification (y-parameter)
1. 𝜋 -Network was constructed as shown in Figure 3.

Figure 3: π-Network Verification (y-parameter) Circuit 1

2. Power supply was to 5𝑉.


3. Value of 𝐼1 and 𝐼2 were recorded in Table.
4. Step 2 and Step 3 were repeated with power supply of 10𝑉 and 15𝑉.
5. The 𝜋 -Network was constructed as shown in Figure 4.

4
Figure 4: π-Network Verification (y-parameter) Circuit 2

6. Power supply was set to 5𝑉.


7. Value of 𝐼1 and 𝐼2 were recorded in Table.
8. Step 2 and Step 3 were repeated with power supply of 10𝑉 and 15𝑉.

RESULT
Table 1: T-Network Verification Result

𝑽𝟏 𝟓𝑽 𝟏𝟎𝑽 𝟏𝟓𝑽
𝑰𝟐 = 𝟎 𝑰𝟏
𝑽𝟐
𝑽𝟐 𝟓𝑽 𝟏𝟎𝑽 𝟏𝟓𝑽
𝑰𝟏 = 𝟎 𝑰𝟐
𝑽𝟏

Table 2: π-Network Verification Result

𝑽𝟐 𝟓𝑽 𝟏𝟎𝑽 𝟏𝟓𝑽
𝑽𝟏 = 𝟎 𝑰𝟏
𝑰𝟐
𝑽𝟏 𝟓𝑽 𝟏𝟎𝑽 𝟏𝟓𝑽
𝑽𝟐 = 𝟎 𝑰𝟏
𝑰𝟐

5
Table 3: Parameters Calculation

𝑽𝑺
𝟓𝑽 𝟏𝟎𝑽 𝟏𝟓𝑽
𝒛𝟏𝟏
𝒛𝟏𝟐
𝒛𝟐𝟏
𝒛𝟐𝟐
𝒚𝟏𝟏
𝒚𝟏𝟐
𝒚𝟐𝟏
𝒚𝟐𝟐

DISCUSSION
Discuss your result in this section, you can make use of the following idea

1. Calculate the parameters using the resistance in the circuit.


2. Calculate the parameters using the Voltage and Current values in the measurement.
3. Compare the results and draw an inference.
4. Discuss any other factor affecting your result and suggestions to it.

CONCLUSION
Conclude your experiment in this section

REFERENCES

APPENDIX

You might also like