IFD9507

Ethernet Communication Module

Application Manual
 Ethernet Communication Module IFD9507

Warning
Please read this instruction carefully before use and follow this instruction to operate the device in order to prevent
damages on the device or injuries to staff.

Switch off the power before wiring.

IFD9507 is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity,
electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g.
key or specific tools are required for operating the enclosure) in case danger and damage on the device may occur.

IFD9507 is to be used for controlling the operating machine and equipment. In order not to damage it, only
qualified professional staff familiar with the structure and operation of IFD9507 can install, operate, wire and
maintain it.

DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check
all the wirings again before switching on the power and DO NOT touch any terminal when the power is switched
on. Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference.

Table of Contents
1 INTRODUCTION...................................................................................................................................4
1.1 Features ......................................................................................................................................4
1.2 Specifications ..............................................................................................................................4
2 PRODUCT PROFILE & OUTLINE .......................................................................................................6
2.1 Dimension ...................................................................................................................................6
2.2 Product Profiles ...........................................................................................................................6
2.3 LED Indicators.............................................................................................................................6
2.4 RJ-11 PIN Definition ....................................................................................................................7
2.5 RJ-45 PIN Definition....................................................................................................................7
2.6 RS-232 PIN Definition .................................................................................................................7
2.7 Address Switch ...........................................................................................................................7
2.8 Data Format ................................................................................................................................8
2.9 Baud Rate for Modbus Communication ......................................................................................8
2.10 Feed-through Terminal PIN Definition .........................................................................................8
3 INSTALLATION & WIRING ..................................................................................................................9
3.1 How to Install...............................................................................................................................9
3.2 How to Connect IFD9507 to Network..........................................................................................9
4 REGISTERS IN IFD9507 ....................................................................................................................10
4.1 Basic Registers (BR) .................................................................................................................10
4.2 Explanations on BR...................................................................................................................10
4.3 Alarm Registers (AL) in IFD9507 ..............................................................................................13

DVP-PLC Application Manual 1

Ethernet Communication Module IFD9507

4.4 In buffer registers (IN) in IFD9507 ............................................................................................ 14

4.5 Out buffer registers (OUT) in IFD9507 ..................................................................................... 15
5 MONITORING FUNCTIONS .............................................................................................................. 15
5.1 Monitor Bit Registers (MB) ....................................................................................................... 15
5.2 Monitor Word Registerss (MW) ................................................................................................ 16
6 SETTING UP DEVICE ADDRESS AND RELAY ADDRESS IN SLAVE MODE (FOR MODBUS TCP
PROTOCOL ONLY) ........................................................................................................................... 17
7 SETTING UP DEVICE ADDRESS AND OTHER NETWORK SETTINGS IN SLAVE MODE ........... 17
8 MODBUS COMMUNICATION ........................................................................................................... 18
8.1 Function Codes Supported....................................................................................................... 18
8.2 Exception Codes Supported..................................................................................................... 18
8.3 Device Type & Device Address................................................................................................. 18
9 ETHERNET/IP COMMUNICATION.................................................................................................... 19
9.1 Service code supported............................................................................................................ 19
9.2 Object supported ...................................................................................................................... 19
9.3 CIP General Status Code (Reference Volume 1:CIP Common Specification Appendix B) ...... 20
9.4 Connection Manager Service Request Error Codes (Reference Volume 1:CIP Common
Specification Table3-5.29) .................................................................................................................. 20
10 SETTING UP THE SOFTWARE - DCISOFT ..................................................................................... 21
10.1 Setting up Communication & Searching for Modules in DCISoft.............................................. 21
10.2 Basic Settings........................................................................................................................... 23
10.3 Network Settings ...................................................................................................................... 24
10.4 Setting up E-Mails .................................................................................................................... 26
10.5 Monitoring Settings................................................................................................................... 27
10.6 IP Filter ..................................................................................................................................... 28
10.7 Ethernet/IP settings .................................................................................................................. 29
10.8 User Defined Settings............................................................................................................... 31
10.9 Virtual COM .............................................................................................................................. 33
10.10 Security Settings....................................................................................................................... 36
10.11 Returning to Default Settings.................................................................................................... 37
11 SETTING UP CONFIGURATION BY HOMEPAGE ........................................................................... 38
11.1 Webpage connection ................................................................................................................ 38
11.2 Basic settings ........................................................................................................................... 39
11.3 Setting up E-Mails .................................................................................................................... 40
11.4 IP filter....................................................................................................................................... 41
11.5 Security Settings....................................................................................................................... 42
11.6 Returning to default setting....................................................................................................... 43
11.7 Monitoring settings ................................................................................................................... 43
11.8 Ethernet/IP................................................................................................................................ 45
11.9 User Define............................................................................................................................... 47

2 DVP-PLC Application Manual

 Ethernet Communication Module IFD9507

12 APPLICATION EXAMPLES – DCISOFT ...........................................................................................49

12.1 Setting up & Unlocking Password .............................................................................................49
12.2 Password Loss (Returning to Default Settings by RS-232).......................................................51
12.3 IP Filter Protection.....................................................................................................................51
12.4 Application of E-Mail .................................................................................................................53
12.5 Monitoring Mode .......................................................................................................................54
12.6 Application of Virtual COM Port.................................................................................................56
13 APPLICATION EXAMPLES – AB SOFTWARE (REVISION:2.10.118.0) ..........................................61
13.1 Serial Slave ...............................................................................................................................61
13.2 Serial Master .............................................................................................................................64

DVP-PLC Application Manual 3

Ethernet Communication Module IFD9507

1 Introduction
Thank you for choosing Delta’s IFD9507 module. To correctly install and operate IFD9507, please read the
manual carefully before using the module.
IFD9507 is an Ethernet communication module for remote setting and communication through Delta’s DCISoft
1.01.
IFD9507 has 3 digital input contacts which will send messages to designated E-Mail addresses after being
triggered. IFD9507 supports Modbus TCP communication protocol and can conduct remote monitoring by using
graphic software or human machine interface. IFD9507 can be the master of Modbus TCP, sending out Modbus
TCP instructions and controlling the peripheral equipment. IFD9507 supports Ethernet/IP communication protocol
and can control device between Ethernet/IP protocols with Modbus protocol. IFD9507 can be a slave as well,
receiving Modbus instructions sent from other masters and transferring them to another Modbus communication
network or Ethernet/IP communication network through Ethernet. In addition, under MDI/MDI-X auto-detection, it
does not need to jump wire in selecting the network cable. See the contents below for more detailed instructions
on IFD9507 module.

1.1 Features
z Auto-detects 10/100 Mbps transmission speed; MDI/MDI-X auto-detection
z The monitor table temporarily stores the monitored data for the user to fast save or acquire the data.
z Supports Modbus TCP protocol (supports Master and Slave mode)
z Supports Ethernet/IP protocol (supports Master and Slave mode)
z Able to send out emails after being triggered.
z The station address, RS-485 communication format and baud rate can be set up externally

1.2 Specifications
„ Network interface

Item Specification

Interface RJ-45 with Auto MDI/MDIX

Number of ports 1 Port
Transmission method IEEE802.3, IEEE802.3u
Transmission cable Category 5e
Transmission speed 10/100 Mbps Auto-Detection
Communication
ICMP, IP, TCP, UDP, DHCP, SMTP, Modbus TCP, Ethernet/IP
protocol
„ Serial communication interface (COM1)

Item Specification

Interface Mini Dim

Number of ports 1 Port
Transmission method RS-232
Transmission cable DVPACAB215 / DVPACAB230 / DVPACAB2A30
Transmission speed 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Communication
Modbus, Delta Configuration, User Define
protocol

4 DVP-PLC Application Manual

 Ethernet Communication Module IFD9507

„ Serial communication interface (COM2)

Item Specification

Interface RJ-11
Number of ports 1 Port
Transmission method RS-485
Transmission speed 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Communication
Modbus, User Define
protocol
„ Terminal block

Item Specification
Interface Feed-through terminal 10PIN
Transmission method RS-485
Transmission distance 1,200m
Transmission speed 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Communication
Modbus, User Define
protocol
Max. number of
32
stations
„ Environment

Item Specification
ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line: ±2KV, Digital Input: ±2KV,
Communication I/O: ±2KV
RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz,
Noise immunity 10V/m
Conducted Susceptibility Test (EN61000-4-6, IEC61131-2 9.10): 150KHz ~
80MHz, 3V/m
Surge Test (Biwave IEC61132-2, IEC61000-4-5):
Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM
Operation temperature 0°C ~ 55 oC (temperature), 50 ~ 95% (humidity), pollution degree 2
Storage temperature -25°C ~ 70 oC (temperature), 5 ~ 95% (humidity)
Vibration/shock International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 &
immunity\ IEC 68-2-27 (TEST Ea)
Certificates IEC 61131-2, UL508

„ Electrical specifications

Item Specification

Power voltage 24VDC (-15% ~ 20%) supplied by feed-through terminal

Power consumption 3W
Insulation voltage 500V
Weight (g) 140g

DVP-PLC Application Manual 5

Ethernet Communication Module IFD9507

2 Product Profile & Outline

2.1 Dimension

Unit: mm

2.2 Product Profiles

1 Communication ports: RS-485, Ethernet, RS-232 6 RS-485 indicator, Reset button, Ethernet indicator
2 Power indicator 7 Module name
8 RS-485 connector, digital input points, power input
3 Address setup rotary switch。
point, earth point
4 Communication format/baud rate setup switch 9 DIN rail connector
5 Message display

2.3 LED Indicators

Name Color Function

POWER Green Power status
RS-485 Green Status of series communication port
LINK/ACT Green Status of network communication

6 DVP-PLC Application Manual

 Ethernet Communication Module IFD9507

2.4 RJ-11 PIN Definition

RJ-11 sketch PIN. Signal Definition

1 -- N/C
2 -- N/C
3 D+ Positive pole for data
4 D- Negative pole for data
5 GND Reference
6 -- N/C

2.5 RJ-45 PIN Definition

RJ-45 sketch PIN Signal Definition

1 Tx+ Positive pole for data transmission
2 Tx- Negative pole for data transmission
3 Rx+ Positive pole for data receiving
4 -- N/C
5 -- N/C
6 Rx- Negative pole for data receiving
7 -- N/C
8 -- N/C

2.6 RS-232 PIN Definition

PIN Signal Content
1 -- N/C
2 -- N/C
3 -- N/C
4 Rx Reception data
5 Tx Transmission data
6 -- N/C
7 -- N/C
8 GND Ground

2.7 Address Switch

Switch setting Content

01…F7 Valid node address setting

DVP-PLC Application Manual 7

Ethernet Communication Module IFD9507

2.8 Data Format

Switch setting Format Switch setting Format
0 7-N-1 8 7-N-2
1 8-N-1 9 8-N-2
2 7-O-1 A 7-O-2
3 8-O-1 B 8-O-2
6 7-E-1 E 7-E-2
7 8-E-1 F 8-E-2

2.9 Baud Rate for Modbus Communication

Switch setting Baud rate Switch setting Baud rate
1 110 7 4,000
2 150 8 9,600
3 300 9 19,200
4 600 A 38,400
5 1,200 B 57,600
6 2,400 C 115,200

2.10 Feed-through Terminal PIN Definition

PIN Signal Content
1 SG Reference ground of signal
2 D- Data-
3 D+ Data-
4 X2 Digital input 2
5 X1 Digital input 1
6 X0 Digital input 0
7 S/S Reference ground of digital input
8 24V +24V input
9 0V 0V input
10 Earth ground

8 DVP-PLC Application Manual

 Ethernet Communication Module IFD9507

3 Installation & Wiring

This section gives instructions on how to connect IFD9507 with other devices and how to connect IFD9507 to
the network.

3.1 How to Install

3.2 How to Connect IFD9507 to Network

Connect IFD9507 to the Ethernet hub by twisted pair cable CAT-5e. IFD9507 has auto MDI/MDIX function;
therefore, IFD9507 does not need to jump wire if selecting CAT-5e.The network connection between the PC and
IFD9507:

PC Master

Ethernet

RS-485 (Master Mode) RS-485 (Master Mode) RS-485 (Slave Mode)

Human
AC motor Temperature
machine
driver controller
interface

DVP-PLC Application Manual 9