Fuel Piping R115-6705 G 01

K280-429 DRAW TUBE FOR

ø559MM (22") TANKS

K280-430 DRAW TUBE FOR

1
ø626MM (24.5") TANKS

K280-431 DRAW TUBE FOR

ø724MM (28.5") TANKS
1

USE QTY (2) W/O "IN TANK" HEATERS

9
2 USE QTY (1) W/SINGLE "IN TANK" HEATERS

USE QTY (0) W/DUAL "IN TANK" HEATERS

2 GEN NOTES:
1) FUEL PIPING - DUAL DRAW AND RETURN, WITHOUT FUEL COOLER,
WITH RETURN FLOW SPLITTER, AND W/ OR W/O CROSSOVER LINE.

2) USE WITH CUMMINS ISX ENGINE.

6 7 8
3) USE WITH MODELS T800 AND W900.
A A
4) USE WITH OR WITHOUT "IN TANK" WATER HEATED FUEL HEATERS.
2 5 5
5) DRAW TUBES (ITEM 1) TO BE INSTALLED IN REAR MOST PORT OF
FUEL TANK ADAPTER.

6) ORIENT THE RETURN TUBE (ITEM 9) INSIDE OF THE TANK TO

3 4 DIRECT RETURNED FUEL AWAY FROM THE DRAW TUBE AND ANGLED
TOWARD THE SIDE OF THE TANK.

7) ORIENT THE ADAPTER FITTINGS ON THE DRAW TUBE (ITEM 1)

AND RETURN TUBE (TEM 9) TO BE ALMOST PARALLEL TO
TANK AND POINTING IN THE DIRECTION OF THE REAR CAB
CROSSMEMBER.
2
8) HOSES FROM THE TEES TO THE FUEL TANKS TO BE EQUAL LENGTH
21 20
21 20 2 WITHIN 1 FT AND NOT LOWER THAN THE TANK ADAPTERS OR
HIGHER THAN THE TEES.

WITH REMOTE MOUNTED FUEL FILTER 19 18 9) BRACKET (ITEM 10) MAY BE POSITIONED FORWARD OF REAR CAB
CROSSMEMBER TO ACCOMODATE HOSE ROUTING REQUIREMENTS.
(R115-6705-2)
10) THIS ASSEMBLY DRAWING SHOWS THE STANDARD SPLITTER VALVE
MOUNTING POSITION. WHEN USED WITH A MANUALLY OPERATED
SPICER AUXILIARY TRANSMISSION, ITEMS 10 THRU 17 ARE
REPLACED WITH (4) K299-420 CLIPS, (4) K077-123-18 CLAMPS,
AND THE NECESSARY BOLTS, WASHERS, AND NUTS.
9 5 2 11) USE R115-6705-1 WITH STD ENGINE MTD FUEL FILTER
1 USE R115-6705-2 WITH OPTIONAL REMOTE MTD FUEL FILTER.
WITH STD ENGINE MOUNTED FUEL FILTER
(R115-6705-1)

05-2

5-1
12) REPLACES COMPUCHECK VALVE IN ENGINE MTD FILTER HEAD

-670
3

-67
WHEN FUEL FILTER RESTRICTION GAUGE IS REQUESTED.

5
R11

R11
- - 21 SUPPLIED WITH ENGINE

- - 20 SUPPLIED WITH ENGINE

1 1 19 SEE TABLE "A" FTG-FILTER OUTLET

1 1 18 SEE TABLE "A" FTG-FILTER INLET

2 2 17 K169-163-10CA NUT

4 4 16 K363-338-2-375 WASHER - FLAT

TOP OF FRAME 2 2 15 K041-804-30CA BOLT
10-5/8" SHOWN
4 4 14 K169-163-6CA NUT

REAR CAB CROSSMEMBER 8 8 13 K363-338-2-250 WASHER - FLAT

11
4 4 12 K041-802-25CA BOLT

2 2 11 K077-123-18 CLAMP

1 1 10 K062-1011 BRACKET-SPLITTER VALVE

15 16 17 2 2 9 K280-294 LINE-FUEL RETURN TUBE

2 2 8 K129-183-0808 FTG,STR CONN,1/2-14 X 3/4-16

1 1 7 K129-186-0808 FTG,90 MALE,1/2-14 X 3/4-16

TABLE "A" FUEL FILTER/WATER SEPARATOR FITTINGS
12 13 14 1 1 6 2252-1 VALVE-RETURN FLOW SPLITTER GT DEVELOPMENT
FILTER FITTINGS
ITEM #18 ITEM #19 OUTLET FITTING
VENDOR MODEL LOCATION 3 3 5 K342-834-08-000 HOSE-FUEL RETURN (#8)
INLET FITTING W/O RESTR GAUGE W/ RESTR GAUGE
ENGINE SUPPLIED W/ ENG SUPPLIED W/ ENG K129-188-0204 3 1 1 4 D2127-2625 FTG-FEMALE ELBOW DYNACRAFT
FS1040 V38-1004 & 10
FRAME D2127-3510 D2127-3510 1 1 3 K129-185-0810 TEE PIPE BRANCH, SAE #010425
K129-188-0204
FLEETGUARD K129-149 & 4 3 2 K342-834-10-000 HOSE-FUEL DRAW (#10)
FH23000 SERIES D2127-3510 D2131-4578
K129-186-0204
FRAME 2 2 1 1 LINE-FUEL DRAW TUBE
61-703-02 & K129-392-1 &
FF2203 K129-188-0810
K129-388-08 K129-186-0204
SECTION A-A QTY QTY ITEM PART NUMBER PRODUCT DESCRIPTION MATERIAL
SCALE 1:4

R115-6705.FM