MasterTop® 1273 AS

Medium load bearing, self-levelling, low emission (AgBB conformity), anti-static epoxy system
with a smooth finish

DESCRIPTION PACKAGING
A medium to heavy duty anti-static, self- MasterTop 1273 AS is supplied as follows:
smoothing 1.5-1.8mm epoxy overlay system
designed to provide a conductive flooring MasterTop P 650 15kg
substrate that eliminates the potential build-up of (2 components)
static electricity. Solvent-free epoxy primer
Copper Tape Rolls
TYPICAL APPLICATIONS Grounding Strips
MasterTop 1273 AS can be used in any MasterTop P 687WAS 15kg
environment where the production process (2 components)
generates dust. Other fields of application Conductive water-based, non-
include: computer rooms, hospital operating solvented, low viscosity, black
theatres and laboratories, processing plants in pigmented primer based on a liquid
pharmaceutical industry and chemical industry, epoxy resin
car industrial paint shops etc. MasterTop BC 372AS 29.9kg
Undesirable electro-static build-up is controlled (2 components)
by using the conductive MasterTop 1273 AS Non-solvented pigmented
system which is grounded. conductive bodycoat

For use on medium duty industrial flooring when TYPICAL PROPERTIES*

a smooth and anti-static surface is required: for The flooring systems fulfils, as minimum
example, electronic industry, clean rooms, requirements, the following properties and
pharmaceutical and space industry etc. technical data determined by internal and
external testing:
ADVANTAGES
 Conductive floor coating EN 13813 SR-B1, 5-AR1-IR40Bfl
 Excellent mechanical strength and anti-static Compressive strength min. 65 N/mm²
properties Slip resistance R9
 Abrasion resistance Taber abrasion 50 mg
 Good adhesion to non-porous substrates (1000R)
 Easy to clean and maintain Fire behaviour Bfl-s1
 Easy to apply according to
 Extremely resistant to a variety of alkalis, DIN EN 13501-1
diluted acids, brine, mineral oils, lubricants Emissions behaviour AgBB conform
and fuels. AFSSET conform
A+ Classification

MasterTop 1273 AS conforms to the following

Standards: -
EN 1081 Rg < 106 Ohms
IEC 61340-5-1 ECF: Rg 104 – 106 Ohms
MasterTop® 1273 AS
APPLICATION GUIDELINES OVERLAY APPLICATION
Mark the floor area out in 10 or 20 m² areas so
SURFACE PREPARATION that consumption can be checked.
Remove laitance, weak or friable concrete and Mix the PTA and PTB of MasterTop BC 372AS
all contaminants that could affect the bond to the together using a slow speed (300-400 rpm), drill
substrate. fitted with a suitable mixing head. Mix until a
uniform streak free colour is obtained. Pour the
Suitable preparation includes light grit blasting, mixed material onto the floor and spread using a
surface grinding etc. Surface defects should be notched trowel to achieve the desired thickness.
repaired using MasterTop 2200 or other suitable Roll with a spiked roller to release entrapped air
repair compounds from the MasterBrace or and ensure a smooth surface. Allow to cure.
MasterEmaco range.
CHEMICAL RESISTANCE
PRIMING Contact the Regional Master Builders Solutions
Mix and apply MasterTop P 650 primer to the Office.
prepared dust free surface at approximately
0.15-0.30 kg/m². COVERAGE / YIELD

Allow to dry. MasterTop P 650 0.15-0.3kg/m²

For the production of anti-static floor coatings, do depending on
not broadcast sand into the MasterTop P 650. surface texture and
porosity
Self-adhesive copper tape with a cross section of Copper Tape Consumption
0.09mm x 19mm (e.g. 3M Scotch) is firmly dependent upon
applied to the cured MasterTop P 650 at configuration of room
distances of about 20m. There should be an MasterTop P 687WAS 0.08-0.10 kg/m²
earthing point for every 100m² floor area. Floors MasterTop BC 372AS 2.3-2.6kg/m²
of less than 100m² should have two earthing
points. THICKNESS
Mix the PTA and PTB of MasterTop P 687WAS
1.5-1.8mm
primer together for at least 3 minutes using a
slow running drill. Pour the mixed material into a
clean container and re-mix. Application is by STORAGE
Store under cover out of direct sunlight and
means of a lambswool roller to the surface protect from extremes of temperature. In tropical
prepared as above. climates the product must be stored in an air-
conditioned environment.
Do not apply MasterTop P 687WAS at
temperatures below +12°C and above +30°C. Failure to comply with the recommended storage
The substrate temperature must be at least 3°C conditions may result in premature deterioration
above the dewpoint. of the product or packaging. For specific storage
Ensure good ventilation during the application. advice consult Master Builders Solutions
Technical Services Department.
MasterTop® 1273 AS
HEALTH AND SAFETY
For further information, a material safety data
sheet is available to the specialist applicator.

QUALITY AND CARE

All products originating from Master Builders
Solutions Dubai, UAE facility are manufactured
under a management system independently
certified to conform to the requirements of the
quality, environmental and occupational health &
safety standards ISO 9001 and ISO 14001.

* Properties listed are based on laboratory controlled tests.

® = Registered trademark of the MBCC Group in many countries.

MBS_CC-UAE/Mtop_1273AS_11_15/v2/04_17/v3/05_20
The technical information and application advice given in this Master Builders Solutions publication are based on
STATEMENT OF the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no
RESPONSIBILITY assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user
is responsible for checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by Master Builders
NOTE Solutions either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they, and not Master Builders Solutions, are responsible for carrying out procedures appropriate to a specific
application.

Master Builders Solutions

Construction Chemicals LLC
P.O. Box 37127, Dubai, UAE
Tel: +971 4 8090800
www.master-builders-solutions.com/en-ae

Disclaimer: the TUV mark relates to

certified management system and not to the
product mentioned on this datasheet