Scribd
Upload
971 views2 pages

LACP Configuration Guide

The document discusses how to create a smartgroup and bind member ports in dynamic mode. It describes configuring the smartgroup and member ports for dynamic LACP load balancing, including setting the LACP mode and load balance settings. It also shows enabling the uplink ports and checking the LACP status and neighbors to confirm successful interconnection between the parties.

Uploaded by

thiago_sampaio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
971 views2 pages

LACP Configuration Guide

The document discusses how to create a smartgroup and bind member ports in dynamic mode. It describes configuring the smartgroup and member ports for dynamic LACP load balancing, including setting the LACP mode and load balance settings. It also shows enabling the uplink ports and checking the LACP status and neighbors to confirm successful interconnection between the parties.

Uploaded by

thiago_sampaio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

秘密▲

Create Smartgroup and Bind Member Port by Dynamic Mode 

Create smartgroup

ZXAN(config)#interface smartgroup1

ZXAN(config-if-smartgroup1)#exit

Configure smartgroup dynamic mode

ZXAN(config)#lacp

ZXAN(config-lacp)#interface smartgroup1

ZXAN(config-lacp-sg-if-smartgroup1)#lacp mode 802.3ad  -------Configure smartgroup dynamic


mode

ZXAN(config-lacp-sg-if-smartgroup1)#lacp load-balance src-mac -- Configure the load balance


mode

ZXAN(config-lacp-sg-if-smartgroup1)#exit

 Member port binds to smartgroup

ZXAN(config-lacp)#interface xgei-1/18/1

ZXAN(config-lacp-member-if-xgei-1/18/1)#smartgroup 1 mode active --- For the dynamic


mode, at least one of the local and peer member ports must join the smartgroup as active

ZXAN(config-lacp-member-if-xgei-1/18/1)#exit

ZXAN(config-lacp)#interface xgei-1/19/1

ZXAN(config-lacp-member-if-xgei-1/19/1)#smartgroup 1 mode active ---- For the dynamic


mode, at least one of the local and peer member ports must join the smartgroup as active

ZXAN(config-lacp-member-if-xgei-1/19/1)#exit

Enable the management status of the uplink port  

ZXAN(config-lacp)#exit

ZXAN(config)#interface xgei-1/18/1

ZXAN(config-if-xgei-1/18/1)#no shutdown -------------------------- The uplink port and PON port


are shutdown by default, first, you need to configure no shutdown to be able to use

ZXAN(config-if-xgei-1/18/1)#exit

ZXAN(config)#interface xgei-1/19/1

ZXAN(config-if-xgei-1/19/1)#no shutdown -------------------------- The uplink port and PON port


are shutdown by default, first, you need to configure no shutdown to be able to use.

ZXAN(config-if-xgei-1/19/1)#exit

If LACP is configured for both parties and the interconnected successfully, the LACP status is shown as below:

ZXAN#show lacp 1 counters

Smartgroup:1

Actor         LACPDUs               Marker    LACPDUs    Marker

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第1页
秘密▲

Port          Tx         Rx         Tx  Rx    Err        Err

-------------------------------------------------------------------

xgei-1/18/1   2605       2548       0   0     0          0

xgei-1/19/1   2605       2556       0   0     0          0

ZXAN#show lacp 1 internal

Smartgroup:1

Flags:              * - Port is Active member Port

                    S - Port is requested in Slow LACPDUs

                    F - Port is requested in Fast LACPDUs   

                    A - Port is in Active mode             

                    P - Port is in Passive mode      

Actor               Agg      LACPDUs  Port  Oper   Port  RX            Mux

Port[Flags]         State    Interval Pri   Key    State Machine       Machine

--------------------------------------------------------------------------------

xgei-1/18/1[SA*]    ACTIVE   30       32768 0x121  0x3d  CURRENT       COLL&DIST

xgei-1/19/1[SA*]    ACTIVE   30       32768 0x121  0x3d  CURRENT       COLL&DIST

ZXAN#show lacp 1 neighbors

Smartgroup 1  neighbors

Actor         Actor     Partner               Partner   Port      Oper    Port

Port          Port No.  System ID             Port No.  Priority  Key     State

-------------------------------------------------------------------------------

xgei-1/18/1   4609      0x8000,cc1a.faea.0ee0 8276      32768     0x1f21  0x3d

xgei-1/19/1   4865      0x8000,cc1a.faea.0ee0 8290      32768     0x1f21  0x3d

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第2页

You might also like