Sist en 13200 4 2007

SLOVENSKI STANDARD
SIST EN 13200-4:2007
01-marec-2007
Prostori za gledalce – 4. del: Lastnosti sedežev
Spectator facilities - Part 4: Seats - Product characteristics
Zuschaueranlagen - Teil 4: Sitze - Produktmerkmale
Installations pour spectateurs - Partie 4: Sieges - Caractéristiques des produits

iTeh STANDARD PREVIEW
(standards.iteh.ai)
Ta slovenski standard je istoveten z: EN 13200-4:2006
SIST EN 13200-4:2007
https://standards.iteh.ai/catalog/standards/sist/4553067f-fa9f-4a1d-a297-
ab560aa40d53/sist-en-13200-4-2007
ICS:
91.040.10 Javne stavbe Public buildings
97.200.10 Gledališka, odrska in Theatre, stage and studio
studijska oprema ter delovne equipment
postaje
97.220.10 Športni objekti Sports facilities
SIST EN 13200-4:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
(standards.iteh.ai)
SIST EN 13200-4:2007
ab560aa40d53/sist-en-13200-4-2007
EUROPEAN STANDARD EN 13200-4
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2006
ICS 91.040.10; 97.200.10; 97.220.10
English Version
Spectator facilities - Part 4: Seats - Product characteristics
Installations pour spectateurs - Partie 4: Sièges - Zuschaueranlagen - Teil 4: Sitze - Produktmerkmale

Caractéristiques des produits
This European Standard was approved by CEN on 28 August 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
(standards.iteh.ai)
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 13200-4:2007
ab560aa40d53/sist-en-13200-4-2007
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13200-4:2006: E
worldwide for CEN national Members.
EN 13200-4:2006 (E)
Contents Page
Foreword.............................................................................................................................................................. 3
1 Scope ...................................................................................................................................................... 4
2 Normative references ............................................................................................................................ 4
3 Terms and definitions ........................................................................................................................... 4
4 Abbreviations ......................................................................................................................................... 5
5 General requirements of construction ................................................................................................ 5
5.1 Seats ....................................................................................................................................................... 5
5.2 General requirements for fixing elements and fixing methods ........................................................ 6
5.2.1 General.................................................................................................................................................... 6
5.2.2 Criteria for presentation of designs..................................................................................................... 7
5.2.3 Acceptance testing ................................................................................................................................ 7
6 Sampling and conditioning................................................................................................................... 7
6.1 Sampling................................................................................................................................................. 7
6.2 Conditioning........................................................................................................................................... 7
7 Characteristics of materials.................................................................................................................. 7
7.1 iTeh STANDARD PREVIEW
General.................................................................................................................................................... 7
7.2 Corrosion resistance ............................................................................................................................. 7
7.3
(standards.iteh.ai)
Resistance to weathering agents/stability to light ............................................................................. 8
7.4 Temperature resistance ........................................................................................................................ 8
SIST EN 13200-4:2007
8 Strength and durability requirements.................................................................................................. 8
9 Test report ............................................................................................................................................
ab560aa40d53/sist-en-13200-4-2007 10
10 Seating numbers.................................................................................................................................. 11
11 Instruction for use ............................................................................................................................... 11
12 Marking ................................................................................................................................................. 11
Annex A (informative) Temperature resistance ............................................................................................. 12
A.1 Temperature resistance ...................................................................................................................... 12
A.1.1 General.................................................................................................................................................. 12
A.1.2 Low temperature test .......................................................................................................................... 12
A.1.3 High temperature test.......................................................................................................................... 12
Annex B (informative) Examples of seats....................................................................................................... 13
Annex C (informative) Ergonomy .................................................................................................................... 15
C.1 Ergonomy ............................................................................................................................................. 15
C.1.1 Anthropometric aspects and data...................................................................................................... 15
C.1.2 Design requirements ........................................................................................................................... 15
Bibliography ...................................................................................................................................................... 24
2
EN 13200-4:2006 (E)
Foreword
This document (EN 13200-4:2006) has been prepared by Technical Committee CEN/TC 315 “Spectators
facilities”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the
latest by April 2007.
EN 13200 Spectator facilities consists of the following parts:
Part 1: Layout criteria for spectator viewing area — Specification
Part 3: Separating elements — Requirements
Part 4: Seats-product characteristics
Part 5: Telescopic stands
Part 6: Demountable (temporary) stands

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
(standards.iteh.ai)
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom. SIST EN 13200-4:2007
ab560aa40d53/sist-en-13200-4-2007
3
EN 13200-4:2006 (E)
1 Scope
This European Standard specifies the mechanical, physical and chemical product characteristics of fixed
seating used in sports venues (indoor and outdoor) in the spectator viewing area (S.V.A.). It also specifies the
criteria for fixing the seating to the structure.
These characteristics and criteria are determined in order to assure an adequate resistance to static and
dynamic stresses and to atmospheric agents. This European Standard specifies comfort, functionality and
safety requirements to prevent serious injury through normal functional use, as well as misuse that might
reasonably be excepted to occur. This European Standard does not include any fire behaviour or resistance
requirements.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 12727, Furniture — Ranked seating — Test methods and requirements for strength and durability
EN 13200-1, Spectator facilities — Part 1: Layout criteria for spectator viewing area — Specification
ENV 581-2:2000, Outdoor furniture — Seating and tables for camping, domestic and contract use — Part 2:
Mechanical safety requirements and test methods for sampling
(standards.iteh.ai)
EN ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics (ISO 527-2:1993 including Corr. 1:1994)
SIST EN 13200-4:2007
EN ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps (ISO
4892-2:2006) ab560aa40d53/sist-en-13200-4-2007
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 179-1:2000, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact
test (ISO 179-1:2000)
ISO 554, Standard atmospheres for conditioning and/or testing — Specifications
3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.
3.1
seating place
space intended for a single spectator in a sitting position (see figures in Annex B)
3.2
seats
 bench, a continuous element, forming a raised seat level with respect to the footway (Figure B.1);
 low back seat, a shaped element or an assembly fixed to the step or on to a support. It has a backrest
with a maximum height of 15 cm above the seat level and may be fitted with armrests (Figure B.2);
4
EN 13200-4:2006 (E)
 high back seat, a shaped element or an assembly fixed to the step or on to a support. It has a backrest
with a minimum height of 15 cm above the seat level and may be fitted with armrests (Figure B.3);
 tip-up seat, a seating place where in the seat elements automatically returns to the upright position on the
departure of the occupant (Figure B.4)
3.3
fixing elements
elements for attaching the seat to the fixed support
3.4
fixing method
assembly of elements for attaching the support or the seats to a stand
3.5
seat numbering
means of identifying seat position
NOTE 1 The different types of seating places which are shown in the figures are only examples.
NOTE 2 For general terms relating to the structures of spectator facilities, see EN 13200-1.
4 Abbreviations

For the purposes of this document, the abbreviations in EN 13200-1 and the following apply.
Bse: dimension of the tread where(standards.iteh.ai)

seating places are (seating row depth);
F: depth of seats including the thickens ofSIST

the EN
back;
13200-4:2007
I: width of seats (minimum dimension for lateral boundaries of a single seating place);
ab560aa40d53/sist-en-13200-4-2007
E: distance between the foremost projection of one seat and the back of the seat in front of it (clearway);
S: height of seat back, including the thickness of the seat.
5 General requirements of construction
5.1 Seats
The seats shall comply with the following general requirements.
a) it shall be so designed to not cause injury to the user. All parts of the seating place with which the user
comes into contact, during the intended use, shall be so designed that physical injury and damage to
spectator property are avoided. The following consideration are necessary:
 the safety distance of accessible movable parts is addressed to EN 294 in any position during
movement;
 all accessible parts are without sharp edges/corners;
 the edges of the seat, backrest and armrests which are in contact with the user when sitting, are
rounded with recommended minimum 3 mm radius;
 the ends of hollow components are closed or capped.
5
EN 13200-4:2006 (E)
b) all parts which are lubricated to assist sliding (greasing, lubricating etc.) shall be designed to protect users
from lubricant stains when in normal use;
c) seats shall be securely fixed to the steps or to the supports;
d) the shape of the seats shall be such as to allow rain and water to drain and shall allow easy cleaning of it
and of the underlying steps;
e) if the components are made of different materials, they shall be compatible with each other;
f) the seating place shall comply the minimum dimensions given in EN 13200-1;
g) the recommended values are given in Table 1.
Table 1 — Recommended dimensional criteria for seats

Row depth (Bse) (mm)
Seat type
min rec
F (mm) I (mm) S (mm)
Bench 300 0 0 700 800

(standards.iteh.ai)
Seat with low back 400 500 < 150 700 800
SIST EN 13200-4:2007
ab560aa40d53/sist-en-13200-4-2007
Seat with high back 400 500 > 150 700 800
5.2 General requirements for fixing elements and fixing methods
5.2.1 General
The fixing of the seats shall comply with the following requirements:
a) the fixing elements of the seats shall withstand the forces generated during the tests described in
EN 12727;
b) it shall not be possible to remove the seats without the use of a special tool;
c) the fixing methods shall be compatible with the supporting structure;
d) the metal elements making up the fixing elements and fixing methods shall be protected against corrosion
(see 7.2);
e) regarding materials, see Clause 6.
6
EN 13200-4:2006 (E)
5.2.2 Criteria for presentation of designs
The design including plans, sections and elevations, and details of the seat, of the fixed support and of the
fixing elements, at an appropriate scale, shall include the declaration of conformity to this European Standard
and a report of the static tests on the seat, and the fixing support structure.
5.2.3 Acceptance testing
An independent agent shall ascertain the compliance between the design and the finished product.
The agent is entitled to accept the declaration of conformity and the calculations contained in the design or to
carry out additional checks.
6 Sampling and conditioning
6.1 Sampling
The minimum number of samples to be tested shall be two.
The samples to be tested shall always be inspected before and after each test, any significant changes that
have taken place shall be recorded.
6.2 Conditioning
At least two weeks in normal conditions, 23/50 according to ISO 554, shall have elapsed between
(standards.iteh.ai)
manufacturing (or assembling) and testing in the case of glued joints in timber and the like.
The tests shall be carried out in normal ambient conditions but, upon agreement, tests may be carried out in
SIST EN 13200-4:2007
special ambient conditions and these shall be recorded in the test report.
ab560aa40d53/sist-en-13200-4-2007
The test samples of other materials shall be contained in normal conditions, 23/50 according to ISO 554 for at
least 72 h.
7 Characteristics of materials
7.1 General
Assessment of the characteristics of materials used in the seating assembly, shall be carried out on the
finished products but might be carried out on test specimens derived from it, after conditioning according 6.2.
The components of seating assembly shall comply with the following requirements.
All components shall comply with the national regulations regarding fire behaviour.
7.2 Corrosion resistance
All metal components of the seating and the fixing elements shall be corrosion resistant.
This requirement is met when, after testing according with ISO 9227 for:
 500 h of exposure for outdoor use;
 200 h of exposure for indoor use.
7
EN 13200-4:2006 (E)
No visual defects are to be noticeable; compliance is checked by visual inspection.
7.3 Resistance to weathering agents/stability to light
Plastic components of the seating shall be exposed to a xenon arc lamp according to EN ISO 4892-2.
They shall be irradiated for a total energy of 8,3 GJ/m² in the wavelength range of 295 nm to 3000 nm.
NOTE In the test conditions of xenon arc lamp described in EN ISO 4892-2 method A, this energy value is achieved
with an irradiation period of 2 300 h when a spectral irradiance of 0,50 W/m²·(at 340 nm) is selected.
The test chamber conditions are the following:
 black panel temperature: 63 °C ± 3 °C;
 relative humidity: 65 % ± 5 %;
 102 min of light;
 18 min of light and water spray.
After exposure, the test specimens shall not show any visual defects on the exposed surface.
The assessment of colour variation rating shall be according to ISO 105-A02, grey scale.

The minimum rating shall be agreed between client and supplier.
(standards.iteh.ai)
Alternative measurements can be performed such as:
 SISTparts
colour variation according to ISO 7724 EN 13200-4:2007
1, 2 and 3 (Lab colour parameters);
 gloss variation according to EN ab560aa40d53/sist-en-13200-4-2007
ISO 2813.
When tested according to EN ISO 527-2, the exposed specimen shall have a maximum yield strain variation
from the unexposed specimen of 30 %.
When tested according to EN ISO 179-1:2000, test method 1 e A, the exposed specimen shall have a
maximum Charpy impact strength variation from the unexposed specimen of 30 %.
7.4 Temperature resistance
See Annex A.
8 Strength and durability requirements

Seats shall be tested according to EN 12727 to assess the mechanical resistance. Several loads and cycles
can be performed according to 4 different levels of severity (1, 2, 3 and 4). At the end of the tests, there shall
be no damage or deformation that will affect the safe use of the seating and the functions shall be maintained.
NOTE It is recommended to perform tests according to level 4 of EN 12727.
8
EN 13200-4:2006 (E)
Table 2 — List of test methods and requirements for strength and durability according to EN 12727
Test Loading 1 2 3 4
Type of use Light Moderate General Severe
Seat static load ) force N 1 300 1 600 2 000 2 000
) 10 times
) combined
Back static load ) force N 560 760 760 760
) 10 times
Horizontal static load to back force N - - 760 760
Vertical static test on back force N - 600 900 900

(standards.iteh.ai)
Arm sideways static load force N 400 600 900 1 000
SIST EN 13200-4:2007
ab560aa40d53/sist-en-13200-4-2007
Arm downwards static load force N 800 900 1 000 1 000
Seat fatigue test ) cycles 50 000 100 000 150 000 200 000
) Seat load 950 N
) combined
Back fatigue test) Back load
) 330 N
Seat front edge fatigue test cycles 50 000 100 000 150 000 200 000
Seat load 950 N

Sist en 13200 4 2007

Uploaded by

Copyright:

Available Formats

Sist en 13200 4 2007

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sist en 13200 4 2007

Uploaded by

Copyright:

Available Formats

SLOVENSKI STANDARD

Prostori za gledalce – 4. del: Lastnosti sedežev

Spectator facilities - Part 4: Seats - Product characteristics

Zuschaueranlagen - Teil 4: Sitze - Produktmerkmale

Installations pour spectateurs - Partie 4: Sieges - Caractéristiques des produits

ICS 91.040.10; 97.200.10; 97.220.10

Spectator facilities - Part 4: Seats - Product characteristics

Installations pour spectateurs - Partie 4: Sièges - Zuschaueranlagen - Teil 4: Sitze - Produktmerkmale

This European Standard was approved by CEN on 28 August 2006.

iTeh STANDARD PREVIEW

EUROPEAN COMMITTEE FOR STANDARDIZATION

Management Centre: rue de Stassart, 36 B-1050 Brussels

EN 13200 Spectator facilities consists of the following parts:

Part 1: Layout criteria for spectator viewing area — Specification

Part 3: Separating elements — Requirements

Part 4: Seats-product characteristics

Part 5: Telescopic stands

Part 6: Demountable (temporary) stands

ISO 554, Standard atmospheres for conditioning and/or testing — Specifications

3 Terms and definitions

iTeh STANDARD PREVIEW

Bse: dimension of the tread where(standards.iteh.ai)

F: depth of seats including the thickens ofSIST

S: height of seat back, including the thickness of the seat.

5 General requirements of construction

The seats shall comply with the following general requirements.

 all accessible parts are without sharp edges/corners;

 the ends of hollow components are closed or capped.

c) seats shall be securely fixed to the steps or to the supports;

g) the recommended values are given in Table 1.

Table 1 — Recommended dimensional criteria for seats

Bench 300 0 0 700 800

5.2 General requirements for fixing elements and fixing methods

c) the fixing methods shall be compatible with the supporting structure;

e) regarding materials, see Clause 6.

5.2.2 Criteria for presentation of designs

5.2.3 Acceptance testing

6 Sampling and conditioning

The minimum number of samples to be tested shall be two.

7.2 Corrosion resistance

 500 h of exposure for outdoor use;

 200 h of exposure for indoor use.

No visual defects are to be noticeable; compliance is checked by visual inspection.

7.3 Resistance to weathering agents/stability to light

The test chamber conditions are the following:

 black panel temperature: 63 °C ± 3 °C;

 102 min of light;

 18 min of light and water spray.

iTeh STANDARD PREVIEW

7.4 Temperature resistance

8 Strength and durability requirements

NOTE It is recommended to perform tests according to level 4 of EN 12727.

Type of use Light Moderate General Severe

Seat static load ) force N 1 300 1 600 2 000 2 000

Back static load ) force N 560 760 760 760

Horizontal static load to back force N - - 760 760

Vertical static test on back force N - 600 900 900

) Seat load 950 N

Back fatigue test) Back load