Feed Pump: Alfa Laval Marine & Power

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

&RPSRQHQW

'HVFULSWLRQ

Feed Pump

Product No. 1767052-01


1767052-02
1767052-03
1767052-04

Printed Dec 2000


Book No. 1818122-02 V1

Alfa Laval Marine & Power


Alfa Laval reserve the right to make changes at any time without
prior notice.
Any comments regarding possible errors and omissions or
suggestions for improvement of this publication would be
gratefully appreciated.
Copies of this publication can be ordered from your local Alfa
Laval company.
Published by: Alfa Laval Marine & Power AB
SE - 147 80 Tumba
Sweden
© Copyright Alfa Laval Marine & Power AB 2000.
Study instruction manuals and observe the
warnings before installation, operation,
service and maintenance.

Not following the instructions can result in


serious accidents with fatal injuries.

P000272A
In order to make the information clear only foreseeable conditions have
been considered. No warnings are given, therefore, for situations
arising from unintended usage of the machine and its tools.

A summary of the safety information is found in the Safety chapter


under divider 1.
Contents

1 Function Description 1

1.1 Application 1

1.2 Design 1

1.3 Working Principle 1

2 Fault Finding 3

3 Maintenance 5

3.1 Disassembly 5

3.2 Assembly 6

4 Technical Data 9

4.1 Specification 9

4.2 Dimensions 10

5 Installation 11

6 Spare Parts 13

1818122-02
1818122-02
1 Function Description

1.1 Application
The feed pump is used to feed lube oil, gas oil,
or marine diesel oil to the separator.

1.2 Design
The pump is of constant flow gear type. The
pump unit consists of an electric motor and a
pump.

1.3 Working Principle


The working part of the pump is a rotor with
internal gears, rotating ab eccentically placed
rotor with external gears..

Due to the suction capacity the pump give a


pulsation free flow to the separator inlet.

Priming
To receive best pump performance, the pump
must first be filled with oil.

If the pump is not completely filled,


disconnect the flexible hose on the separator
inlet and fill with oil.

Direction of Rotation
The pump rotates in an anti-clockwise
direction, as seen from the pump to the
electric motor.

1818122-02 1
1 Function Description Feed Pump

2 1818122-02
2 Fault Finding

)DXOW 3UREDEOHFDXVH 5HPHG\


Low capacity or Suction valves shut off, or clogged strainer Open the valves, or clean the strainer
low pressure

Pump does not Pump too dry Fill the pump housing with oil
prime
Air leak on suction side of the pump Seal off the air leak

Drive motor tends The counter pressure after the pump is too Check the valves between pump and separa-
to stop by tripping high tor
the overload relay
The cut-off setting of the motor relay is too Adjust the relay setting according to the motor
low power rating in Amps

Pump noisy when Suction valves shut off, or clogged strainer Open the valves, or clean the strainer
running

Air leak on suction side of the pump Seal off the air leak

Heavy wear in the pump Dismantle the pump and replace the worn
parts

1818122-02 3
2 Fault Finding Feed Pump

4 1818122-02
3 Maintenance

:$51,1*

(QWUDSPHQWKD]DUG

Do not start maintenance work unless


the power is switched off and the
inlet and outlet are shut.

3.1 Disassembly
1. Remove the capscrews and the head from
the pump. It may be necessary to apply a
slight pressure on the drive end of the
rotor shaft to free the ehad from the
casing. Do not pry the ehad from the
casing as this may damage and mar the
gasket surfaces.

CAUTION: The rotor and shaft is made of


two pieces and the shaft can move in the rotor
if tapped too hard. Carefully check rotor and
shaft assembly before reassembling the pump.
2. Remove the idler from the idler pin. If the
idler pin is worn, both the head and idler
pin, and idler should be replaced.
3. Next, completely remove the rotor and
shaft from the casing by exerting perssure
on the drive end of the shaft.
4. Remove the packing nut.

1818122-02 5
3 Maintenance Feed Pump

5. The pump is now ready for removal of


mechanical seal, see fig. It is
recommended to replace the mechanical
seal after disassembly.
6. All parts should be examined for wear
before reassembly. When making major
repairs, such as replacing the rotor and
shaft, a new casing bushing should be
used.

Replacing the casing bushing

The casing bushing should be replaced as


follows:

Insert a bar approximately 15/16" diameter


and at least 3½" long in the seael of the casing
and press the bushing out of the casing.

When installing a new carbon graphite


bushing, extreme care should be taken to
prevent breakage as carbon graphite is a brittle
material and easily cracked. When cracked,
the bushing may quickly disintegrate in
operation. An arbor press shouldalways be
used and the bushing should be installed in
one even uninterrupted stroke of the press.
Dip the bushing in lube oil and start the
bushing in the head end of the casing. Press
until located to the "A" dimension is 1-3/16"
to 1-¼".

The end clearance within the pump is


governed by the location of the casing bushing
as well as the number of head gaskets. To
correctly position the casing bushing in the
casing, see no. 3 in assembly.

3.2 Assembly
1. Clean all parts thoroughly.
2. Place the rotor and shaft in the casing.

6 1818122-02
Feed Pump 3 Maintenance

3. Put the head gasket on the head and the


idler on the idler pin projecting from the
head. Replace the head in the casing;
thighten cap screws.
4. If a new casing bushing has been installed
in the casing, use only .002" gasket on the
head and tighten the cap screws evenly
and securely. This will position the
bushing correctly in the casing. remove
the head, add one .002" head gasket and
replace the capscrews and tighten
securely.
5. Turn the rotor by hand to be curtain it
turns without any problems.
6. When reassembling a mechanical seal
pump, place the spring washer and spring
on the shaft.
7. Coat the shaft and the inside of the rubber
bellows of the seal rotary member with
light oil. Slide the rotary member part way
down the shaft.
1% The lapped face of the carbon wear
ring must face toward the shaft end of
the pump. Be sure the notches on the
edge of the carbon wear ring mate with
the retainer lugs in the rotary member.

1818122-02 7
3 Maintenance Feed Pump

8 1818122-02
4 Technical Data

4.1 Specification
Media Lube oil, Marine diesel oil (MDO), Gas oil
Maximum media temperature 80 °C
Pump type Gear
Max. capacity Lube oil 360 l/h at 50 Hz or 430 l/h at 60 Hz
Diesel oil 630 l/h at 50 Hz or 760 l/h at 60 Hz

Diesel oil 630 l/h, 24V DC


Mounting style Horizontally
Weight incl. electric motor 8,5 kg, 110/230V AC
11 kg, 24V DC
Material
Pump housing Cast iron
Rotor with vanes Steel
Stator Steel
Sealing Mechanical seal, carbon wear ring
Motor
Insulation According to class F
Enclosure IP 54
Speed 1400 rpm at 50 Hz
1680 rpm at 60 Hz
1400 rpm,24V DC
Power consumption 0,25 kW

$UWLFOH1R 9ROWDJH )UHTXHQF\ &XUUHQW )ORZOK +] )ORZOK +]


1767052-04/03 110/230V 50/60 Hz 1,5/3,0 A 360 430
1767052-02/01 110/230V 50/60 Hz 1,5/3,0 A 630 760

1767088-01 24V DC 13 A 630

1818122-02 9
4 Technical Data Feed Pump

4.2 Dimensions

Ref. 1767052 Rev. 0

Article No. A B C D E F G H J K L M Voltage Current

1767052-01 412 140 180 NPT 1/2" 40 196 90 7 112 122 48 17 230 VAC 1,5A

1767052-02 412 140 180 NPT 1/2" 40 196 90 7 112 122 48 17 110 VAC 3,0A

1767052-03 412 140 180 NPT 1/2" 40 196 90 7 112 122 48 17 230 VAC 1,5A

1767052-04 412 140 180 NPT 1/2" 40 196 90 7 112 122 48 17 110 VAC 1,5A

10 1818122-02
5 Installation

The feed pump must be installed to meet the


following demands:
• The pump must be installed on a solid
foundation and on a drip tray or in a
cofferdam. It must be installed in
horizontal position.
• The suction height must not cause a
pressure exceeding 0.4 bar (40 kPa).

Storage

If the pump is to be stored, or not used for six


months or more, the pump must be drained
and a light coat of non-detergent SAE 30
weight oil must be applied to all internal pump
parts. Lubricate fittings and apply grease to
pump shaft extension. To ensure proper
function of the pump after storage, it is
recommended to circulate the oil in the pump
every 30 days by rotating the pump shaft by
hand one complete revolution.

1818122-02 11
5 Installation Feed Pump

12 1818122-02
6 Spare Parts

,WHP 4W\ $UWLFOH1R 'HVFULSWLRQ


1 1767116-01 Head gasket

2 1767116-02 Idler pin

3 1767116-03 Mechanical seael

4 1767116-04 Gasket for cap

5 1767116-10 Electric motor 1 phase 230 VAC

5 1767116-11 Electric motor 1 phase 110 VAC

5 1767116-12 Electric motor 1 phase 24 VDC

6 Casing bushing

1818122-02 13
6 Spare Parts Feed Pump

14 1818122-02

You might also like