PRODUCT DESCRIPTION MAXIFLOOR® MFT 323 SL epoxy coating is a solvent-based, fast cure, two component epoxy resin floor coating offering excellent chemical and abrasion resistance. The finished surface is high gloss, seamless, hygienic and available in a range of attractive colors.
RECOMMENDED USE MAXIFLOOR® MFT 323 SL epoxy coating can be applied at various thickness to meet the exact requirement. Particularly suitable for areas requiring a chemically resistant coating such as: • Laboratories • Warehouses • Hospitals • Food processing facilities • Chemical manufacturing plants • Beverage production areas • Dairies • Kitchens
Excellent adhesion to concrete, mortar, screed and a limited number of other surfaces make MAXIFLOOR® MFP 250 HB epoxy concrete primer ideal for many medium to heavy industrial areas.
PRODUCT DATA Color Shown in the color card Solids by weight (mixture) 90 ± 2% Finish Gloss Flash Point > 100°C (Setaflash) Flexibility Good Water Resistance Good Theoretical DFT 1000 microns Theoretical coverage 1.21 m2/Kg-set Specific gravity (mixture) 1,2 Hard dry 10 hours (30°C) Full cure 7 days (30°C) Bonding strength 2.5 N/mm2 (concrete failure) Packaging 5 Kg-set & 20 Kg-set Storage stability One year if stored cool and dry and in original not opened boxes (Do not store below freezing point)
APPLICATION Application Method Roller or Brush Mixing ratio (by weight) Comp.A : Comp.B = 4 : 1 Re coating interval 12 – 18 hour (30°C) Temperature Minimum 10°C Maximum 40°C Pot-life 12 minutes at 25°C (reduced at higher temperatures) 45 minutes after poured on to the floor Thinner/Cleaner Epoxy Thinner Recommended Primer MAXIFLOOR® MFP 250 HB TECHNICAL DATA MAXIFLOOR® MFT 323 SL EPOXY COATING Theoretical Coverage 1.50 m2/Kg-set at 500 µm (Dry film thickness) 0.75 m2/Kg-set at 1000 µm (Dry film thickness)
Note: Practical coverage rates will be affected by surface profile/porosity and application techniques.
SURFACE PREPARATION Compressive strength of concrete floor must be more than 25 N/mm2. Direct trawl finish concrete without cement render is the best surface condition for epoxy flooring. Age of concrete should be more than 28 days and moisture content should be less than 5%. The temperature of the substrate must be at least 3°C above the current dew point temperature. Good ventilation is necessary when the paint is used in confined spaces. Correct substrate preparation is critical for optimum performance. Surfaces must be structurally sound, clean and free from loose particles, oil, grease and all other contaminants. Remove oil, grease and wax contaminants by scrubbing with industrial grade detergent or degreasing compound followed by mechanical cleaning. Cement laitance, loose particles, mould release agent, curing membrane and other contaminants must be removed from surface by shot blasting, scarifying or grit blasting followed by vacuum cleaning. After pretreatment of the substrate, the bonding strength of the substrate must be at least 1.5 N/mm2. MAXIFLOOR® MFP 250 HB epoxy concrete primer should not be exposed to water, chemicals or mechanical stress until it is fully cured.
RECOMMENDED SYSTEMS The following are examples only. System thickness depends on floor requirement. 1) 1 x MAXIFLOOR® MFP 250 HB 50 µm (D F T) 1 x MAXIFLOOR® MFT 323 SL 500 µm (D F T)
2) 1 x MAXIFLOOR® MFP 250 HB 50 µm (D F T)
1 x MAXIFLOOR® MFT 323 SL 1000 µm (D F T)
HEALTH AND SAFETY
A health and safety data sheet is available for this product on request. Please observe the precautionary notices on the container. Apply under well-ventilated conditions. Do not breathe or inhale vapour. Avoid skin contact. Spillage on skin should immediately be removed with suitable cleaner, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
CONTAMINATION If the surface preparation system used has not removed deeply penetrating contamination such as oil, blasting the substrate with hot compressed air followed by an application of a sealing compound can be considered. Consult your local MAXIFLOOR® Technical Department for further information.
DISCLAIMER The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product is often used under conditions beyond our control, we cannot guarantee anything but the quality of the product itself. We reserve the right to change the given data without notice.
