19 CSPR
19 CSPR
Service
Service
Service
Horizontal Frequency
30kHz – 83kHz
TABLE OF CONTENTS
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Revision List
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
V-Frequency 55-75Hz
ON Mode ≤37W
EPA ENERGYSTAR®
OFF Mode ≤1W
Luminance
OSD Setup;Extra
Regulatory Compliance CE
Connecting Cables
1. Power Cord
2. Signal Cable
3. Audio Cable
Connecting the Power Cord: Connect the power cord into your LCD monitor’s power input socket, and then plug
the other end into a 3-pin AC power outlet. The power cord may be connected to either a wall power outlet or the
power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor.
Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect
the other end to the computer’s D-Sub port.
Connecting the Audio Cable: Connect the audio cable between the monitor’s audio input and the PC’s audio
output.
Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).
Main
Main Menu Sub Menu
Menu Sub Menu Description
Item Item
Icon
Brightness Backlight Adjustment
1 5
6 10
11 15
10
11
12
13
2 Y
3
5 N
7 N
8
10 N
11
N N
12 13
Y Y
14 15 N
16
17
N
18 19
14
1) MCU initializes.
2) Is the EPROM blank?
3) Program the EPROM by default values.
4) Get the PWM value of brightness from EPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EPROM.
Turn on the LED and set it to green color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappears.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
15
D-Sub Connector
(CN101)
16
AC input +16V
Bridge Rectifier Transformer
EMI filter Rectifier diodes
and Filter (T901)
+5V
Start Resistor
(R904,R905,R906)
PWM Control
LD7552DPS Power Switch
(U901) (Q901)
Photocoupler Regulator
(IC903) (IC904)
Inverter +16V
Connector Transformer MOSFET
(T801,T802) (Q804,Q809)
(CN801,CN802,
CN802,Q804)
MOSFET
(Q805,806,810,811)
Transistor ON/OFF
PWM Control
Feedback Circuit (Q801,Q802)
TL494IDR
(U801)
DIM
17
TSUM1PFR SCHEMATIC
XGA/SXGA LVDS OUTPUT
DSUB_R+ DSUB_R+ VCC1.8
DSUB_R- DSUB_R-
DSUB_G+ DSUB_G+ VCC3.3
DSUB_G- DSUB_G- VCC1.8
DSUB_SOG DSUB_SOG CMVCC
DSUB_5V DSUB_B+ DSUB_B+
DSUB_B- DSUB_B- VCC3.3 CMVCC1
ESD_VCC DSUB_H DSUB_H
DSUB_V DSUB_V
VCC3.3 DSUB_5V DDC1_SDA DDC1_SDA CMVCC
DDC1_SCL DDC1_SCL
ESD_VCC DET_CABLE DET_CABLE
CMVCC1
VCC3.3
02.Input
VCC1.8 CMVCC
VCC3.3 PA[0..1]
PA[0..1] PA[0..1]
DSUB_5V VCC1.8 PA[4..9] CMVCC
on_BACKLIGHT on_BACKLIGHT PA[4..9] PA[4..9]
PB[0..9]
CMVCC VCC3.3 PB[0..9] PB[0..9]
Mute Mute
Volume# Volume# PPWR_ON# PPWR_ON#
CMVCC1 DSUB_5V PANEL_ID# PANEL_ID#
Adj_BACKLIGHT Adj_BACKLIGHT
CMVCC
VCTRL VCTRL
ESD_VCC
CMVCC1
ESD_VCC
18
R110
100R 1/16W 5% 10 DSUB_5V
DDC1_SCL DSUB_SCL 15 5 VGA_PLUG
5 DDC1_SCL DSUB_5V
9 R109 C106
DSUB_5V 5
14 4
DSUB_SOG 5
2
8 VGA_B-
R113 13 3 VGA_B+ 390 OHM 1/16W 0.047uF
100R 1/16W 5% 7 VGA_G- ZD103 ZD104
DDC1_SDA DSUB_SDA 12 2 VGA_G+ UDZSNP5.6B UDZSNP5.6B FB103
5 DDC1_SDA VGA_R-
6 R111 C107
1
11 1 VGA_R+ VGA_G+ 1 2
DSUB_G+ 5
BEAD
DB15 100R 1/16W 5% 0.047uF
17
R112 C108
FB101
GND POWER DGND R115 C110
VGA_R+ 1 2
DSUB_R+ 5
BEAD
100R 1/16W 5% 0.047uF
R116 C111
AZC099-04S C115
NC
VCC3.3
U102 ESD_VCC
VGA_G+ VCC3.3 7
1 6
2 I/O1 I/O4 5
VGA_R+ 3 GNDVDD 4 VGA_B+
I/O2 I/O3 R118
1K 1/16W 5%
AZC099-04S C114
NC VGA_PLUG
DET_CABLE 5
19
U401
51
30
53
7 VCC3.3
6
52 300OHM
VDDP
VCTRL 7
AVDD_ADC
VDDC
VDDC
VCTRL C403 C404
33 PA0
13 LVA3P 34 PA1 0.1uF/16V 0.1uF/16V
3 DSUB_R+ RIN0P LVA3M
12
3 DSUB_R- RIN0M PA[0..1]
10
3 DSUB_G+ GIN0P PA4 PA[0..1] 5
9 35
3 DSUB_G- GIN0M LVA2P PA5
11 36
3 DSUB_SOG SOGIN0 LVA2M PA6
8 37
3 DSUB_B+ BIN0P LVA1P PA7
7 38
3 DSUB_B- BIN0M LVA1M PA8 VCC1.8 VDDC
16 39
3 DSUB_H HSY NC0 LVA0P PA9
17 40
3 DSUB_V VSY NC0 LVA0M
18
3 DDC1_SDA DDCA_SDA/RS232_TX PA[4..9] 7 VCC1.8
19
3 DDC1_SCL DDCA_SCL/rs232_RX PA[4..9] 5
C406 C407
0.1uF/16V 0.1uF/16V
PB[0..9]
PB0 PB[0..9] 5
41
LVB3P 42 PB1
LVB3M 43 PB2
LVBCKP 44 PB3
LVBCKM 45 PB4
LVB2P 46 PB5
LVB2M 47 PB6
LVB1P 48 PB7
4 LVB1M 49 PB8 EE_WP
AVDD REXT LVB0P PB9
R403 390 OHM 1/16W 50
LVB0M
15 R425 C418
VCC3.3 C401 REFP
NC NC
0.1uF/16V 14 CMVCC
REFM
CMVCC 7
C408 20 R424 NC
0.22uF16V U402 GPIO_P15/PWM0 27 R426 100R 1/16W 5% R406
PWM2/GPIO_P24 PANEL_ID# 7
1 8 21 LVDS
R408 2 CE# VDD 7 22 SDO 55 R452 NC MSDA 10K 1/16W 5%
WP 3 SO HOLD# SCZ GPIO_P12 on_BACKLIGHT 7
6 R456 0R05 1/16W 23 56 R409
WP# SCK SCK PWM1/GPIO_P25 adj_BACKLIGHT 7
10K 1/16W 5% 4 5 R457 0R05 1/16W 24 20K OHM 1/16W
VSS SI SDI 57
R405 100R 1/16W 5%
28 RSTN 58 R411 100R 1/16W 5% KEY 2
CMVCC1 SST25LF020A-33-4C-SAE GPIO_P27/PWM1 GPIO_P00/SAR1 59 R412 100R 1/16W 5% KEY 1
GPIO_P01/SAR2
54 C409 0.1uF/16V
+
C429
26 R453 R454 R455
GPIO_P10/I2C_MCL PPWR_ON# 6
25 R413 100R 1/16W 5% U403 NC
GPIO_P11/I2C_MDA DET_CABLE 4
NC NC NC 8 1
31 EE_WP 7 VCC NC 2
32 MODE[0] MSCL 6 WC E1 3
GND
GND
GND
VCC3.3 NC / M24C04-WMN6TP
TSUM1PFR-LF
CONN 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 10K 1/16W 5% 0.1uF/16V 10K 1/16W 5% NC \ CONN
20
CN403
PA[0..1] PB[0..9]
5 PA[0..1] 5 PB[0..9]
1
PA0 PB0 2
PA1 PB1 3
PB2 R434 C420 4
PA[4..9] PB3 5
5 PA[4..9] PB4 330 OHM 1/4W 0.1uF/16V 6
PA4 PB5 7
PA5 PB6 PA0 8
PA6 PB7 PA1 9
PA7 PB8 PB2 10
PA8 PB9 PB3 11
PA9 PA4 12
PA5 13
14
PA6 15
PA7 16
17
3D PA8 18
PA9 19
PB0 20
PB1 21
1 2 PB2 22
CMVCC G S PB3 23
24
AO3401L PB4 25
CMVCC 7 PB5 26
PB6 27
R433 C419 PB7 28
PB8 29
R435 10K 1/16W 5% 0.1uF/16V PB9 30
100uF25V
21
DSUB_5V
CMVCC
DSUB_5V 2
3
5, 6 CMVCC
D403 D401 VCC3.3 VCC3.3
BAT54C NC/BAV99
CN404
3
1 SM340A CMVCC1
2 D402 10K 1/16W 5% 10K 1/16W 5%
3 CMVCC
CMVCC CMVCC1 5 BKLT-EN VCC1.8
4 Q410
5 BKLT-VBRI R450 NC R449 KN2907AS
6 BKLT-EN NC(R0402) Q406
C_PANEL_INDEX VCC1.8 5
7 NC 2N3904S-RTK/PS
Volume PANEL_ID# 5
8 C425 Q409
9 Mute KN2907AS C432 + C423
Mute 5 on_BACKLIGHT 5
NC
5 VCTRL
R440 0.1uF/16V 100uF25V
4K7 1/16W 5%
CONN
VCC3.3 VCC3.3
CMVCC1 MVCC FB403 NC
VCC3.3
R446 R447
VCC3.3
NC 10K 1/16W 5%
R441 3
Volume VIN 2
VOUT VCC3.3 4, 5
1K 1/16W 5% 1
Q408 + C426 C428 ADJ(GND)
R442 2N3904S-RTK/PS
BKLT-VBRI 100uF25V 0.1uF/16V U404 C422 + C427
adj_BACKLIGHT 5
AP1117D33LA
Volume# 5
100R 1/16W 5% 0.1uF/16V 100uF25V
R448
4K7 1/16W 5%
22
R918 L904
100 OHM 1/4W
R919
2A(INVERTER)
100 OHM 1/4W +16V
FB904 C912
BEAD R920 0.001uF ZD902
100 OHM 1/4W
R946 RLZ18B
1 2 + + 150 OHM 2W
C917
!
2
FB902 680uF25V C918
! !
1
FCH10A15
2 3 3 2 R904
300K OHM 1/4W C932 R939
+ C905 C938 R903 5 8 1K 1/8W
BD901 120UF450V
NC/1500pF2KV C906 100KOHM +-5% 2WS 7 0.001uF
-
-
6 9
R961100 OHM 1/4W
0.001uF JUMP
1 10 +5V
R906 D901 F903
R962 100 OHM 1/4W
300K OHM 1/4W FR103 12 + FUSE
3 11 C939 +
1000uF25V R924 C915
R909 150R 1/8W 470uF16V
2
5.1 OHM 1/4W
2
+
ZD906 C907 C908 D900 D907
NC/RLZ22B 0.1uF 22uF/50V FR107 31DQ06FC3 ZD921 ZD922
RLZ20B RLZ5.6B R940
4
NC
1
IC903
L901 U901
!
1
PC123X2Y FZOF
2
4 5
! 3
2
RT
VCC
NC
CS
6
7
D903 LL4148
Q901
FB901
BEAD R927
4
COMP VCC
3
! ! 0.047uF R938
10K 1/8W FB903
C935
0.001uF
R902 R901 BEAD C924 R951
1M 1/4W 1M 1/4W 0.1uF 100R
R912 D908
R942
2
3 1 MBRF2060CT 1K 1/10W 1%
R926
! R914 1K 1/10W 1%
0.39 OHM 2W
C903 C928 C909
0.47uF/275V 1000pF 470pF/25V IC904
KIA431A-AT/P
NR901
NTCR !
R930
C900 2.43K OHM 1% 1/10W
3300pF 250V L906
F901
FUSE
!
!
C902 C901
1000PF/250VAC 1000PF/250VAC L905
1 F902
2 1 HS2 HS4 2 jump
EMI shield (NC/H85G0002-1) Heat-sink(Q90G6263-6) 3 + C916
CN901 4 1000UF16V + C934 C930 C940
+5V 1000UF16V 0.1uF 0.1uF
SOCKET 1 1 5
! 2 2
DIM
ON/OFF
6
7
8
C931 9
10
0.1uF 11
12
13
HS3 HS5
Heat-sink(Q90G6263-6) Heat-sink(Q90G6263-6)
1 1 VOL
2 2
MUTE
23
3
C801
3 18pF/6KV L801
+16V NC / L
R802 4 CN802
2
100R 1/8W C825 CONN
18pF/6KV
R804 0R05 1/8W 1
R805 HV
2
1 8 2
Q802 NC/4K7 1/10W 5% R810 LV
R808 1 Q801 R850
10K 1/10W 1% PDTC144WK PDTA144WK 15R 1/4W 5% 15R 1/4W 5% POWER X'FMR
R806 R807
ON/OFF
3
1K 1/8W 1K 1/8W
2
1uF/16V DTC D801
D802
3
BAV99
D813 ZD801 BAV99
R813 D803 R814 FB NC/LL4148 NC/RLZ6.8C Q804 R811
100R 1/10W 5% LL4148 75K 1/10W 1% Q812 AM9945N-T1-PF 1K 1/8W 1% R812
1
NC/RK7002 1K 1/8W 1%
DIM
1
1M 1/10W 5%
0.1uF/16V
5
Q803 R815 R803
R817
C804
2
PMBS3904 47K 1/10W 1% NC /1K 1/10W 5%
D
R816 C819 D814
68K OHM 1% 1/10W 1uF/16V D815 NC/SM260A 2A/60V
G
S
S
NC / SM260A 2A/60V
1
C805 FB
4
470uF/25V
+
C823
0.1uF/25V
R818 C806 R819 R853
2M 1/10W 1uF/16V 10K 1/10W 1% DTC 10K 1/10W 1% Q810
PMBS3904 Q811
R820 PMBS3904
560K OHM 1/10W
Q805
D812 U801 TL494IDR PMBS3906
C807 Q806
LL4148 R842 1 16 PMBS3906
0.1uF/16V 47K 1/10W 2 1IN+ 2IN+ 15 R845
D811 3 1IN- 2IN- 14 22R 1/10W 5%
LL4148 4 FEEDBACK REF 13 R847
5 DTC OUTPUT CTRL 12 R844
R825 51K OHM 1% 1/8W
GND E2
R843
8 9 R846
C1 E1
R822 47K 1/10W
R826
22R 1/10W 5%
C808
180KOHM1/8W
220pF
R827 2.2uF/16V
1M 1/8W 5%
1K 1/10W 1% C810
0.1uF/25V R848 R849
R852
C809
1K 1/10W 1% 1K 1/10W 1%
10K 1/10W 1%
R828 R829
47K 1/10W CN803
68K OHM 1% 1/10W
Q807 CONN
PMBS3904 C816 T802 R830 0R05 1/8W
C820 1500PF/50V 6 7 1
D806 C827 C828 2 HV
R831 1uF/16V LV
Q808 BAW56 0.0047uF 0.0047uF
10K 1/10W 1%
3
RK7002 D807 1 R837 C812
B OLP1
LL4148 15R 1/4W 5% 3 18pF/6KV L802
3 NC / L
C R833 4 CN804
10K 1/10W 1%
2
1
2 C826 CONN
E OLP2
1
C824 18pF/6KV
S
G
1
2 BAV99 BAV99
E OLP4
R839
C818 C817 C822 1K 1/8W 1% R841
0.0022uF 0.0022uF 1500PF/50V 1K 1/8W 1%
2
FB
24
+5V1
+ C604 C602 C603
R602 0.47uF/16V100uF/25V 0.47uF/16V
10K 1/10W 5%
R603
VOL
10K 1/10W 5% C609
1uF/25V
10K 1/10W 5%
R609 IC601 IC APA2069 CN602
8 9 LOUT- WAFER 2.0MM 4P
R604 SE/BTL LOUT-
CN601 7 10
4 Lin C601 6 VOLUME VDD 11 LOUT+ 4
5 0.47uF/16V 5 LIN- LOUT+ 12 3
3 4 GND GND 13 2
2 Rin 10K 1/10W 5% C606 3 GND GND 14 ROUT+ 1
R605 0.47uF/16V RIN- ROUT+
1 2 15
1 BY PASS VDD 16 ROUT-
SHUTDOWN ROUT-
27KOHM +-5%
PHONEJACK
+5V1
10K 1/10W 5%
R610
R611
4.7KOHM +-5%
R601
10K 1/10W 5% C612 C608
R608 + C605 0.1uF/16V 1uF/25V
0R05 1/8W 22uF/50V
Q607
6.2KOHM +-5%
PMBS3904
6.2KOHM +-5%
3.6KOHM +-5%
MUTE
C610 C611
R607
100pF 100pF
R606
C613
0.1uF/16V
R612
Q608
RK7002
HS1
NC
FB602
BEAD 1
2
1 2
25
715G2835 1
LED_RED# LED_GRN#
1
LED001
LED
2
CN001
POWER
DOWN
CONN
MENU
OK
UP
SW005 SW004 SW003 SW002 SW001
1 2 1 2 1 2 1 2 1 2
SGND
ZD002
ZD005
5
ZD003
5
ZD004
5
ZD001
5
C007
SW
C009
SW
C010
SW
C008
SW
C006
SW
3 4 3 4 3 4 3 4 3 4
NC/UDZS5.6B
NC/UDZS5.6B
NC/UDZS5.6B
NC/UDZS5.6B
NC/UDZS5.6B
NC/0.1uF
NC/0.1uF
NC/0.1uF
NC/0.1uF
NC/0.1uF
SGND
CONNECTOR
26
27
28
29
30
31
No power
NG
U404 Vout=3.3V
NG
OK Replace X401
Replace U401
32
No picture
NG X401 oscillate NG
The button if under control
waveform is normal Replace X401
OK OK
U404 Vout=3.3V OK
Replace U401
OK
CN101 is normal
NG
Check Correspondent
component
OK
Replace U401
33
White screen
OK OK NG Replace X401
NG
NG Check Correspondent
Check Correspondent component.
component. OK
OK
Replace U401
Replace PANEL
34
NG
OK Check AC input
NG
Check bridge rectified circuit and F901 circuit
OK
NG
OK Check R904, R905, R906, Change U901
NG 1) Check U901
OK
2) Check D900, D901 circuit
NG
OK Check U901
Check Q903/IC903/IC904/ZD921/ZD922
35
Check C802=16V
NG
OK Check adapter
NG
OK Check main board
NG
OK Change ON/OFF circuit
NG
OK Change U801
NG
OK Check U801
NG
OK Check Q810/Q805/Q811/Q806
NG
OK Change T801, T802
36
NG
Is Key Pad Board connecting normally? Connect Key Pad Board
OK
NG
Replace Button Switch
Is Button Switch normally?
OK
NG
Is Key Pad Board Normally?
Replace Key Pad Board
OK
37
4. Bias adjustment:
5. Gain adjustment:
Move cursor to “-F-” and press MENU key
2. Switch the MEM .channel to Channel 3 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 313 ±30, y = 329 ±30, Y>180cd/m2
4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory window until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
38
2. Switch the MEM .channel to Channel 4 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 302 ±30, y = 318 ±30, Y>180cd/m2
4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory window until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
2. Switch the MEM. Channel to Channel 9 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 283 ±30, y = 297 ±30, Y>150cd/m2
4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory window until chroma 7120 indicator reached the value G=100
6. Adjust the BLUE on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
2. Switch the MEM .channel to Channel 10 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 313 ±30, y = 329 ±30, Y>180cd/m2
4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory window until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE of on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
39
No. Description
1 B E Z E L (L 1 9 W A -8 Q 5 )
2 LEN S
3 KEY PAD
4 KEY BOARD
5 PANEL
6 POW ER BOARD
7 M A IN B O A R D
8 M A IN F R A M E L 1 9 W A -8 Q *
9 SPK
10 R EAR C O VER 19"
11 H IN G E
No. P/N
12 STAND TOP
S1 S C R E W (0 M 1 G 1 7 3 0 6 1 2 0 )
13 STAND S2 S C R E W (0 M 1 G 1 3 0 5 1 2 0 )
14 BASE 8S2 S3 S C R E W (A M 1 G 1 7 4 0 1 2 4 7 C R 3 )
15 FOOT S3 S C R E W (A M 1 G 1 7 4 0 1 2 4 7 C R 3 )
40
41
50