Bawana BOQ

FOR OFFICIAL USE ONLY NOT FOR PUBLICATION
TENDERERS COPY ORIGINAL COPY
TENDER
SPECIFICATION
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784
FOR CIVIL, STRUCTURAL & ARCHITECTURAL WORKS FOR CERTAIN MISC BUILDINGS AND TG HALL CIVIL WORKS AT 2X750 MW PRAGATI -III COMBINED CYCLE POWER PROJECT AT BAWANA, DELHI.
PART II PRICE BID
Bharat Heavy Electricals Limited (A Govt. Of India Undertaking) Power Sector Northern Region, Plot No. 25 , Sector - 16A , Distt. Gautam Budh Nagar, NOIDA 201 301(INDIA)
Bharat Heavy Electricals Limited

(A Govt. Of India Undertaking) Power Sector Northern Region, Plot No. 25 , Sector - 16A , Distt. Gautam Budh Nagar, NOIDA 201 301(INDIA)
Phone: 0091-0120-2416273 / 2416279 / 2515476 Fax 091-0120-2515464/ 2515467 Email: [email protected] / [email protected]
ISO 9001, ISO 14001 and OHSAS 18001 certified company SubContract and Purchase Deptt.
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784
IMPORTANT NOTE PURCHASER OF THIS TENDER DOCUMENT IS ADVISED TO CHECK AND ENSURE COMPLETION OF ALL PAGES OF TENDER DOCUMENT AND REPORT ANY DISCREPANCY TIMELY FOR CORRECTIVE ACTION, IF ANY, TO THE ISSUING AUTHORITY BEFORE THE BIDS ARE SUBMITTED. ORIGINAL COPY OF TENDER DOCUMENT COMPLETE IN ALL RESPECTS MUST BE SUBMITTED BACK AS PART OF THE BID WITHOUT WHICH THE SAME IS LIABLE TO BE REJECTED BY BHEL.
THIS TENDER SPECIFICATION ISSUED TO: M/S-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CIVIL, STRUCTURAL & ARCHITECTURAL WORKS FOR CERTAIN MISC BUILDINGS AND TG HALL CIVIL WORKS AT 2X750 MW PRAGATI -III COMBINED CYCLE POWER PROJECT AT BAWANA, DELHI TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 100 DESCRIPTION OF ITEM Earth work in excavation, back filling and disposal as per specification, drawings and as per directed by the Engineer for the followings. Earth work in excavation upto 2m depth below ground level for foundation, trenches, pile line, storm water, drains, etc. including setting out, clearing and grooving removal of debris, dewatering if required, strutting, shoring/ sheet piling if required, dressing the sides, leveling to grade and ramming the bottom, stacking/disposal of surplus excavated materials including leveling the earth if required with a lead of 1 KM etc. complete for all type of soils including literate morum, etc. which can be excavated by means of crow bar, pick axe, etc. does not require chiseling or blasting. Cum UNIT Total Quantity UNIT RATE (IN RS) AMOUNT RS) (IN
101
45827
103
Earth work in excavation for depth exceeding 2m but not exceeding 4m below ground level for foundation, trenches, pipe line, storm water, drains, etc. including dewatering if required strutting, shoring/sheet pilling if required, dressing the sides, leveling to grade and ramming the bottom, stacking/disposal of surplus excavated materials including leveling the earth if required within a lead of 1km etc. complete for all types of soils including laterite, morum etc. which can be excavated by means of crowbar, pick axe etc. but does not require chiseling or blasting. Earth work in excavation for depth exceeding 4m but not exceeding 6m below ground level for foundation, trenches, pipe lines, storm water, drains, etc. including dewatering if required strutting, shoring/sheet pilling if required, dressing the sides, leveling to grade and stacking/disposal surplus excavated materials with in a lead of 1 km etc. complete for all types of soils including laterite, morum etc. which can be excavated by means of crow bar, pick axe etc. but does not require chiseling or blasting. Earth work in excavation for depth exceeding 6m but not exceeding 8m below ground level for foundation, trenches, pipe lines, storm water, drains, etc. including dewatering if required strutting, shoring/sheet pilling if required, dressing the sides, leveling to grade and ramming the bottom stacking/disposal surplus excavated materials including leveling the earth if required with in a lead of 1 km etc. complete for all types soils including laterite, morum etc. which can be excavated by means of crow bar pick axe etc. but does not require chiseling and blasting.
Cum
18565
105
Cum
9617
107
Cum
4258
3
BAWANA-PRAGATI/CIVIL PART/784 Page 1 of 26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 109 DESCRIPTION OF ITEM Earth work in excavation for depth exceeding 8m but not exceeding 10m below ground level for foundation, trenches, pipe lines, storm water, drains, etc. including dewatering if required strutting, shoring/sheet pilling if required, dressing the sides, leveling to grade and ramming the bottom stacking/disposal surplus excavated materials including leveling the earth if required with in a lead of 1 km etc. complete for all types soils including laterite, morum etc. which can be excavated by means of crow bar pick axe etc. but does not require chiseling and blasting. UNIT Cum Total Quantity 1808 UNIT RATE (IN RS) AMOUNT RS) (IN
116 (a) Disposal of surplus excavated earth beyond an initial lead of 2 K.m dumping and leveling the dumped soil and leveling the areas from where the material is transported, complete with all lifts as specified and directed by Engineer. 116 (b) Extra disposal over 116(a) of surplus excavated earth/rock beyond an initial lead of 2 K.m and upto 3 K.m dumping and leveling the dumped soil and leveling the areas from where the material is transported, complete with all lifts as specified and directed by Engineer. 118 (a) Back filling around foundations in plinths etc. to proper grade and level with specified soil within a lead beyond 1 k.m but not exceeding 5 K.m from available excavated materials including reexcavating loose thickness, watering and ramming 118(b) Back filling around foundations and plinths etc to proper grade and level with selected excavated soil directly from excavation area within a lead of 1Km including watering and ramming/compacting in layers of 15cm thickness to atleast 90% of its maximum dry density for cohesive soils and to 75% relative density for noncohesive soils by manual/ mechanical means, dressing etc complete including transportation. 119 Back filling around/below foundations and plinths to proper grade and level with selected Cohesive Non Swelling (CNS) soil including watering and ramming in layers of 30 cm. thickness to 90% Standard procter density by manual/ mechanical means in saturated condition, dressing etc. complete including transportation. Providing and injecting chemical emulsion (1 part chemicals * 20 parts water * 1% emulsion) for preconstructional antitemite/weed treatment as per IS:6313 with chemicals conforming to IS:8963 and creating a chemical barrier under and around the column pits, wall trenches, basement excavation, back feed, top surface of plinth feeling, junction of wall along external pre meter of building floor together with plinth protection expenses joint surround piles and conduits etc. as per specification and as directed by Engineer In-charge. For treating the bottom surface sides of excavation, emulsion @ 5 liters/Sqm of surface area and for treating the back fits around columns, walls, etc. emulsion @ 7.5 liter/Sqm of the surface shall be used and treatment shall be done in stage following the compaction of each in layers(plinth area of building at ground floor shall be measured). Supply and filling sand under floors, in foundation and plinths including cost of sand, transporting for all leads, loading, unloading, spreading in layers in 25 cm loose thickness at all depths, watering, compaction with mechanised compaction machine or manually to minimum 80% of relative density, dressing and leveling etc complete.
Cum Cum
48930 3610
Cum
37976 1824
CUM
Cum
350
120
SQM
26145
121
Cum
744
4
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 122 DESCRIPTION OF ITEM Providing and laying rubble soiling with specified sizes of approved quality hard rock or hard broken and metal of size ranging from 63 mm and down aggregates, at all position and depths below or above finished ground floor level, below foundations, below flooring and for providing hard standing etc in one layer if approximately 225 mm thickness hand packing. filling in interstices with send including watering, toughly compacting the layer all complete as per specification and the direction of the Engineer. PROVIDING AND PLACING CONCRETE WORK INCLUDING COST OF LABOUR, MATERIALS AND EQUIPMENT FOR HANDLING, TRANSPORTATION, BATCHING, MIXING, PLACING, VIBRATING AND CURING (EXCLUDING COST OF CENTERING, SHUTTERING AND REINFORCEMENT) COMPLETE AT ALL ELEVATIONS AS PER DRAWING SPECIFICATIONS UNLESS SPECIFIED OTHER WISE AND AS DIRECTED BY ENGINEER FOR THE FOLLOWING . Plain cement concrete of grade M 7.5 as leveling course for filling, underwater structures, foundations, trenches etc all complete. Plain cement concrete of grade M 10 as leveling course for filling, underwater staining structures, equipment foundations etc all complete. Plain Cement concrete of grade 1:24 as plinth protection etc all complete. Concrete of grade M-25 conforming to IS:456 with coarse sand and graded hard stone agg. 20mm nominal size in all foundation, underground works, water retaining structures and outdoor works floor etc . At any level below finished floor level, any shape, position of thickness etc complete including use of plasticizer /super plasticizer conforming to IS:9103 (latest) to achieve required slump in concrete to all complete Concrete of grade M-25 conforming to IS:456 with coarse sand and graded hard stone agg. 20mm nominal size in super structure at all height from finished floor level at any level ; shape position or thickness complete including use plasticizer /super plasticizer conforming to IS:9103 (latest) to achieve required slump in concrete all complete. Concrete of grade M-35 conforming to an ISO -456 with coarse sand and graded hard stone aggregate 20mm nominal size for foundation of stem turbine & gas turbine at all height/ depth form finished ground floor level including addition of suitable plasticizer / super plasticizer conforming to IS:9103 (latest) to achieve a slump >125mm in concrete as per manufacture's recommendation etc all complete. The rate shall also include conducting non destructive ultrasonic plus velocity test as per specification to find out soundness of concrete including all equipments, tools, plants scaffolding required for testing preparation of test report etc all complete as directed by engineer. CL 15.19.01 Concrete of grade M-25 conforming to IS:456 with coarse sand and graded hard stone aggregate 20 mm nominal size in precast works like trench covers, lintels, etc including formwork/moudds for thickness varying from 50 mm to 250 mm including transportation, erection, fixing in position at all elevations and use of plasticizer whatever required all complete excluding the cost of reinforcement Concrete of grade M-20 conforming to IS:456 with coarse sand and graded hard stone aggregate 20 mm nominal size in in paving, etc. complete. Cum Cum Cum Cum 330 3307 112 23250 UNIT Cum Total Quantity 3361 UNIT RATE (IN RS) AMOUNT RS) (IN
200
201 202 203 205
206
Cum
9711
207
Cum
500
208
Cum
583
209
Cum
1763
5
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 211 DESCRIPTION OF ITEM Breaking existing concrete work at any level including cutting reinforcements removing the rubbish within a lead of 1 K.m including making good the broken edge/surface with cement mortar, painting, finishing to match with existing finishing, scaffolding/supporting at any level all complete and as directed by Engineer. Providing and encasing of structural steel member with concrete (M25) work around flunges, webs, etc. and filling the gap. Encased member shall be wrapped with chicken wire mesh with 50 mm lap etc. complete as per specification and as directed by Engineer. Providing underbed for paving and ground floor for all buildings by preparation and consolidation of sub grade required level, laying of stone soling of 225 mm compacted thickness with 63 mm and down aggregate, filling the interstices with selected sand followed by 75 mm thick 1:4:8 PCC with (1 part cement: 4 parts sand and 8 parts stone aggregate) with 40 mm nominal size aggregate for all lifts all complete as per specification and instruction of Engineer In-charge. Providing Bitumen coating to all surfaces of foundations (except piles) and substructures in contact with soil with three coats of hot applied industrial bitumen conforming to IS: 702 (latest) of Grade 85/25 at the rate of 1.7 kg/sq/m/coat with anti-stripping compound. Extra over so. no. 207 above, for controlling of temperature of freshly laid concrete to loss than 25 degree centigrade using ice, including all related arrangements for providing, storing and mixing of ice with water cooling of aggregate, etc. all complete as per specification, drawing and instruction of Engineer-In-charge. Chipping of concrete in reinforced concrete work, cutting pockets, making openings at all levels and according to shapes, disposal of waste materials upto a lead of 2 km as directed by engineer including equipment, safety precautions etc all complete as per specification, drawing, instructions of engineer in charge but excluding cutting of reinforcement Supplying and fixing and removing formwork at any elevation including all labour, material, scaffolding complete including pockets etc. as per specification and as directed by Engineer for the following. Ordinary form work below finished ground floor level for foundation, footings, base of columns, walls, columns, plasters, beams, mass concrete, trenches etc.( Used Plywood in good condition shall be used , MS shuttering not permitted ) Fairface form work above finished ground floor level for columns, beams, suspended floors, roots, lintels, cantilevers, staircases, landings, balconies, domes, arches etc. for all heights. Providing, fixing and removing formwork in block-out/pockets and openings (below 0.1 Sqm cross sectional area) at elevations including cutting, formation of all shapes and all other operations required for making the required shape & size all complete as per specification, drawing and instruction of engineer In-charge. Upto 300 mm depth. From 301 mm upto 600 mm depth. From 601 mm upto 1000 mm depth. REINFORCEMENT UNIT Cum Total Quantity 25 UNIT RATE (IN RS) AMOUNT RS) (IN
212
Cum
105
213
Sqm
11089
214
100 SQM Cum 500
215
216
55 CUDM
300 301 304 307
Sqm Sqm
69631 29181
(i) (ii) (iii) 400
Nos. Nos. Nos.
60 60 50
6
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 401 DESCRIPTION OF ITEM Providing, straightening, cutting, bending , placing in position at any level, binding in position of mild steel reinforcements conforming to garde-1 of IS: 432 (part-I) including cost of binding wire, labour, transportation to and from stores etc. complete all as per specification, drawings and directed by Engineer. Providing, straightening, cutting, bending , placing in position at any level, binding in position of steel reinforcements shall be TMT HYSD bars of grade Fe-415 and/or Fe-500 conforming to relevant IS codes, including cost of binding wire, labour, transportation to and from stores etc. complete all as per specification, drawings and directed by Engineer. Providing, straightening, cutting, bending , placing in position at any level, binding of mild steel reinforcements in brick work including cost of reinforcement and binding wire, labour, etc. complete all as per specification, drawings. Providing, straightening, cutting, bending , placing at any level, binding in position high yield strength steel reinforcements in brick work including cost of reinforcement and binding wire, labour etc, complete all as per specification, drawings. WATER PROOFING AS PER SPECIFICATIONS Providing and mixing approved water proofing in concrete or cement mortar for works wherever specified or directed as per specification/ manufacturer's instructions, testing of sample for water proofing etc. complete. Providing under bed over roof slab, floors to achieves the specified slab with 1:4 cement motar plaster (by volume) of minimum 25 mm thickness at all elevation including all labour, material, equipment, handling, preparation of surface, transpiration, batching, mixing, placing, leveling, cutting, testing, etc. complete as per specification, drawing and instructions engineer. Screed concrete 1:2:4 conforming IS:456 with coarse sand and graded hard stone aggregate 12.5 mm/ 6 mm nominal size on the roof at any level or thickness maintain the required grade concrete. Screed concrete 1:2:4 conforming IS:456 with coarse sand and graded hard stone aggregate 12.5 mm/ 6 mm nominal size in manholes. Providing and lying proactive wearing course of 25 mm thick PCC (1:2:4) with 6 mm down aggregate laid in 1200 x 1200 Sqm panels alternatively cost reinforced with 0.56 mm dia galvanised chicken wire mess with a gap of 6 mm between two adjacent panels, gaps shall be filled with silicon sealant/elastomeric water proofing membrane, all complete with labour, materials, equipment and as per specification/drawing and to the satisfaction of engineer in charge Providing, lying and fixing water proofing treatment using high solid content liquid applied based elastomeric water proofing membrane minimum 1.5 mm thick with separate wearing course (as per ASTM C898 and 836) including application of polymerised mastik to achieve smooth surface and primer coat at all elevation in vertical and horizontal surface etc, including all labour, material, equipment, handling, scaffolding, transporting, testing etc, complete as per drawing, specification and instruction of the engineer (Wearing coat to be paid separately). UNIT MT Total Quantity 2 UNIT RATE (IN RS) AMOUNT RS) (IN
402
MT
2470
403 404 500 501 502
MT MT
2 5
KG Sqm
64214 8145
503 504 505
Cum Cum Sqm
418 5 8045
506
Sqm
8045
7
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 507 DESCRIPTION OF ITEM Providing and lying pressed precast chequered concrete tiles over water proofing of minimum size 250 x 250 and minimum thickness 22 mm conforming to IS:13801 including 15 mm thick cement mortar (1:4) bedding inclusive of provision for thermal expansion for each roofing tile filled with polysutifide joint sealant (water proofing paid else where). Supplying and filling in position hot applied bitumen sealing compound (Grade A) confirming to IS:1834 including cleaning, mixing, heating, pouncing/injecting sealing compound in gaps in joints at all levels including application of primer, labour, material, equipments etc. all complete as per specification/drawing, instruction of engineer in charge. Supply & installation of bitumen impregnated fiber board confirming to IS:1838 as joint fitter at joints in concrete including nailing, coating of both faces with coal tar pitch/bitumen, labour, materials, equipments etc all complete at all levels as per specification, drawing and instruction of engineer in charge. 12mm thick joints 20mm thick joints 25mm thick joints M.S. EMBEDMENT Supply, fabricating and fixing of embedment, MS inserts, pipe sleeves, guide raits, angle pieces, rungs of various diameters, plates of dimension as required including cost of all labour, materials and equipment, transportation, loading, unloading, handling, welding, cutting, drilling, scaffolding and setting complete as per specifications, drawings and as directed by Engineer. Steel shall be issued free of cost by BHEL. Supply, fabrication, transportation, delivery at site and erection, installation and alignment of MS Foundation bolts (grade-1 of IS:432 & IS:2062) assembly in concrete along with nuts, look nuts (IS:1363, IS:1364 & IS:3138), washers, anchor plates, stiffeners plates, protective tapes etc. upto inclusive of 63 mm diameter and upto 2000 mm long, for columns templates including furnishing of labour, materials, equipments, welding, cutting, girding, threading, drilling, pipe sleeves wherever necessary etc. all complete as per specification and as directed by engineer. Sqm Sqm Sqm MT 65 25 412 107 UNIT Sqm Total Quantity 510 UNIT RATE (IN RS) AMOUNT RS) (IN
602
KG
100
604
604-a 604-b 604-c 700 701
702
MT
10
703
Transportation from stores, delivery at work spot and erection, installation and alignment of embedment, MS inserts, pipe sleeves, rails, guide rails, angle places, anchor bolts, foundation, bolts of various diameters, plates of dimensions, as required including cost of all labour, equipment material, loading, unloading etc. all complete as per specifications, drawing and as directed by Engineer
MT
74
8
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 704 DESCRIPTION OF ITEM Providing, fabricating, transporting, erecting and installing at all elevations miscellaneous steel PVC pipes, expansion fasteners in concrete/brick wall, for all kinds, including the cost of labour, materials and equipment, setting material in concrete, layout, scaffolding, handling at site, cutting, forming, grinding, drilling, bolting welding jointing, testing etc all complete as per drawings and specifications and instructions of engineer. MS pipes of all diameters PVC conduits of all sizes Expansion fasteners (galvanised) of HILTI make or equivalent of safe tension capacity as specified below 250 kg 500 kg 750 kg GROUTING AS PER SPECIFICATION FOR THE FOLLOWING : Providing & grouting of pocket holes, pipe sleeves of any shape and size under base plate after erection and alignment if necessary of main structural steel work at any elevations including roughening surface, cleaning ramming, cutting, etc. with Conbextra GP-1 / GP-2 or equivalent all complete as per specifications. (cost of all material and cleaning the pocket by compressed air shall be in the scope of the contractor). Providing & grouting of pocket holes, pipe sleeves of any shape and size under base plate after erection and alignment if necessary of secondary structure, machinery and pipe supporting structure at any elevations including roughening surface, cleaning, ramming, cutting, etc. with 1:1:2 cement-sand- 6 mm down stone chips all complete as per specifications. (cost of all material and cleaning the pocket by compressed air shall be in the scope of the contractor). DOORS, WINDOWS, VENTILATORS, LOUVERS, ROOF VENTILATORS, ROLLING SHUTTERS, PARTITIONS ETC. COMPLETE INCLUDING FRAMING, KICK PLATES, STOPPERS AS PER SPECIFICATION, DRAWINGS AND AS DIRECTED BY ENGINEER FOR THE FOLLOWING:Providing and fixing of 40 mm thick solid core flush door shutters ( single or double) with commercial faces and hard board edges, core of solid core doors shall be of block board or wood particle board of approved make with glazed vision panel including all fixtures, Godrej make Mortice lock with handle on both sides, shop painting/polishing as per specification all complete including test certificates Providing and fixing steel windows of fixed type with steel sections as per IS : 1038, IS:1361 & IS : 7452 latest revision, Glazing shall be of 6.0 mm thick multiwall polycarbonate plain/tinted sheets including all fittings, metal beadings, hold fasts, primer painting as per specification all complete. Providing and fixing steel openable windows/ ventilators with steel sections as per IS : 1038, IS:1361 & IS : 7452 latest revision, Glazing shall be of 6.0 mm thick float glass (plain) panes including all fittings, metal beadings, hold fasts, primer painting as per specification all complete. Quintal Quintal Each Each Each Cum UNIT Total Quantity UNIT RATE (IN RS) AMOUNT RS) (IN
(i) (ii) (iii) (iv) (v) 800 804
5 10 52 53 51 26
805
Cum
10
900
901
Sqm
62
902
Sqm
122
903
Sqm
147
9
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 904 DESCRIPTION OF ITEM Providing and fixing steel openable windows/ ventilators with steel sections as per IS : 1038, IS:1361 & IS : 7452 latest revision, Glazing shall be of 4.0 mm thick float glass (tinted) panes including all fittings, metal beadings, hold fasts, primer painting as per specification all complete. Providing and fixing anodized extruded aluminum windows (single or double shutter) including aluminum frame conforming to IS:1948 , IS:1949 fabricated from extruded sections of JINDAL or approved equivalent having minimum 3.0 mm wall thickness as per IS:1285, IS:733 and electro color coating of minimum 15 microns thickness. Glazing shall be clear / tinted float glass of 6.0 mm thickness including snap fit type beading, concealed screws, fixtures. Approved make Mortice lock with handle on both sides etc. complete. Aluminum section shall be smooth free of stains, straight, mitered & jointed mechanically wherever required. NA NA Providing and fixing anodized extruded aluminum ventilators conforming to IS:1948 , IS:1949 fabricated from extruded sections of approved makes having minimum 3.0 mm wall thickness as per IS:1285, IS:733 and electro color coating of minimum 15 microns thickness. Glazing shall be clear / tinted float glass of 6.0 mm thickness including snap fit type beading, concealed screws, fixtures, etc. complete. Aluminum section shall be smooth, free of stains, straight, mitered & jointed mechanically wherever required. Providing and fixing anodized extruded aluminium ventilators conforming to IS:1948, IS:1949 fabricated from extruded sections of approved make having minimum 1.5mm wall thickness as per IS:1285, IS:733 and electro color coating of minimum 15 microns thickness. Glazing shall be tinted float glass of 4.0 mm thickness including snap fit type beading, concealed screws, fixtures, etc complete. Aluminium section shall be smooth, free of stains, straight, mitred & jointed mechanically wherever required. NA Providing and fixing steel single or double door shutters. Shutter shall be 35 mm thick flush design comprising of two outer sheets of 1.2 mm thickness rigidity connected and reinforced inside with continuous vertical 1 mm stiffeners shall be reinforced by continuous pressed steel channel with minimum 1.2 mm the door shall be sound deadened by filling the inside void with mineral wool, spot welded in position at not more than 150 mm on centres including all fittings. Approved make Mortice lock with handle on both sides, primer painting complete as per specification Providing and fixing fire proof steel door shutters (single or double shutter) conforming to IS:3614 (part-1 & part-2). Shutters shall be minimum 60mm thick flush design comprising of two outer sheets of 18 gauge steel rigidly connected and reinforced inside with continuous vertical 20 gauge stiffeners, spot welded in position at not more than 150 mm on centres with mineral wool insulation, primer and epoxy based painting including door frame, all fittings complete as per specification, and shall be TAC approved with minimum 2 hrs. fire rating. UNIT Sqm Total Quantity 80 UNIT RATE (IN RS) AMOUNT RS) (IN
905
Sqm
640
906 907 908
Sqm
166
909
90 SQM
910 911
Sqm
115
912
Sqm
25
10
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 913 DESCRIPTION OF ITEM Providing and fixing anodized extruded aluminum doors (single or double shutter) conforming to IS:1948, IS:1949 fabricated from extruded sections of approved make having minimum 3mm wall thickness as per IS:1285, IS:733 and electro color coating of minimum 15 microns thickness, Glazing shall be clear float glass of 6.0mm thickness including snap fit type beading, concealed screws, fixtures, Approved make Mortice lock with handle on both sides etc complete, Aluminum section shall be smooth, free of stains, straight, mitred & jointed mechanically wherever required. (Frames shall be measured and paid under separate item) UNIT Sqm Total Quantity 255 UNIT RATE (IN RS) AMOUNT RS) (IN
914
916
Providing and fixing in position anodised aluminum frame for doors, windows, ventilators having minimum 3mm wall thickness as per IS:1285 and electro colour coating of minimum 15 micron thickness including holdfast, filling up of gapes at junctions, at top, bottom and sides etc all complete as per specification. Providing and fixing aluminum glazed portion, Aluminum sections shall be of extruded sections of approved make having minimum 3mm wall thickness as per IS:1285, IS:733 and electro color coating of minimum 15 microns thickness, Glazing shall be clear float glass of 5.5mm thickness including snap fit type beading, concealed screws, hold fast, fixtures, Godrej make Mortice lock with handle on both sides, necessary filling up of gaps at the junctions, at top, bottom and sides, etc complete. Aluminum section shall be smooth, rust free, straight, mitred & jointed mechanically wherever required. Providing and fixing aluminium glazed partition with double glazing. Aluminium sections shall be of extruded sections of approved make having minimum 3mm wall thickness as per IS:1285, IS:733 and electro color coating of minimum 15 microns thickness. Double glazing shall be of two clear float glass of 6 mm thickness sealed and separated by 12mm air-gap including colour anodised aluminium beading, concealed screws, hold fast, fixtures, PVC/neoprene gasket, necessary fillingup of gaps at the junctions, at top, bottom and sides, etc complete. Aluminium section shall be smooth, rust free, straight, mitred & jointed mechanically wherever required. Minimum anodising thickness shall be 15micron. Providing aluminum by engineer. Providing steel grill engineer. Providing and fixing by Engineer. Providing and fixing by Engineer. grill for windows and ventilators of approved quality and design as directed for windows and ventilators of approved quality and design as directed by of over head hydraulic door closers of approved make & quality as directed floor mounted Hydraulic door closer of approved make & quality as directed
KG
535
Sqm
250
917
351
SQM
918 919 921 921 a
Sqm Sqm Nos. Nos.
221 65 70 36
11
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 923 DESCRIPTION OF ITEM Providing and fixing in position rolling shutter of hot rolled double dipped galvanised steel lath section of 18 SWG tested mild steel strips at 75mm rolling centres interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation including wire springs, top cover, primer & shop coats of approved enamel paint etc, all complete as per specification and approved make - Mechanically operated conforming to IS:6248. The bottom lath shall be coupled to a lock plate fabricated from 3mm thick galvanised steel plate and security riveted with stiffening angles. Providing and fixing in position rolling shutter of hot rolled double dipped galvanised steel lath section of 18 SWG tested mild steel strips at 75mm rolling centres interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation including wire springs top cover, primer & shop coats of approved enamel paint etc, all complete as per specification and of approved make - electrically operated conforming to IS:6248. The bottom lath shall be coupled to a lock plate fabricated from 3mm thick galvanised steel plate and securely riveted with stiffening angles. BRICKWORK MASONRY INCLUDING SUPPLY OF MATERIAL, COST OF LABOUR ETC. COMPLETE, AS PER SPECIFICATIONS. Providing brick work in cement mortar 1:6 (1 part cement : 6 part coarse sand) in walls, chambers etc. in thickness varying from 230 mm to 460 mm at all depth, places and positions below plinth including raking out joints, cutting, scaffolding etc. complete excluding plastering and painting. Using fly ash lime bricks conforming to IS:12894 with crushing strength of 75 Kg/cm2. Using ordinary bricks of class designation 7.5 of nominal dimension. Providing brick work in cement mortar 1:6 (1 cement 6 coarse sand) in walls, chambers etc. in thickness 230mm at all heights, places and position above plinth including raking out joints, cutting, scaffolding etc complete excluding plastering and painting. Using fly ash lime bricks confirming to IS:12894 with crushing strength of 75 kg/cm2. Using ordinary bricks of class designation 7.5 of nominal dimension. Using locally available first class bricks of required crushing strength of nominal dimension approved by engineer in charge/customer. Providing brick work in cement mortar 1:4 (1 cement 4 coarse sand) in partition walls, chambers etc. in thickness 115 mm at all heights, places and position above or below plinth/graded level including providing H.B. wetting at every third layer, raking out joints, cutting, scaffolding etc complete using fly ash lime bricks confirming to IS:12894 with crushing strength of 75 kg/cm2 and clay ash bricks shall be as per IS:13757, minimum percentage of fly ash shall be 25% excluding plastering and painting as per specification. Using fly ash lime bricks confirming to IS 12894 with crushing strength of 75 kg/cm2 Using ordinary bricks of class designation 7.5 of nominal dimension. UNIT Sqm Total Quantity 81 UNIT RATE (IN RS) AMOUNT RS) (IN
925
Sqm
249
1000 1001
(i) (iii) 1002
Cum Cum
161 100
i) iii) iv) 1004
Cum Cum Sqm
1880 300 50
i) (iii)
SQM Sqm
518 50
12
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1008 1010 DESCRIPTION OF ITEM Breaking of existing brick work at all level including plastering, removing the rubbish up to a distance of 500 m including transportation, loading, unloading etc. all complete as directed by the engineer. Providing and encasing of structural steel member with masonry work around flanges, webs etc. and filling the gap between steel and masonry by minimum 12mm thick mortar. Encased member shall be wrapped with chicken wire mesh with 50mm lap etc. complete as per specification. Making opening in existing brick wall or partition wall including making good the broken edges/surface with cement mortar etc. complete. Supply and placing in position mild steel wire fabric of square mesh 25 mm size and wire diameter of 2 mm for encasing of steel sections in concrete including cutting, bending, fixing etc. complete. DAMP PROOF COURSE INCLUDING AL MATERIALS, LABOUR, SHUTTERING, CENTERING, CURING ETC., COMPLETE WITH THICKNESS AS SPECIFIED/SHOWN ON DRAWINGS OR AS DIRECTED BY ENGINEER FOR THE FOLLOWING :Damp proof Course 50mm thick 1:1.5:3 concrete (10mm and down graded aggregate) with 2% of approved admixture of water proofing compound. Two layers of hot bitumen coating 85/25 grade as per IS:702 @ 1.7kg./sqm shall be applied before & after the DPC as per specification. CEMENT MORTAR PLASTER INCLUDING MAKING GROOVES WHEREVER REQUIRED, ALL MATERIALS, SCAFFOLDING, CURING ETC. COMPLETE AS PER SPECIFICATION, DRAWING AND AS DIRECTED BY ENGINEER FOR THE FOLLOWING:Providing 18mm thick plaster in two layers outside the building wall in cement mortar 1:6 on walls, finished to a smooth finish as per specification including providing 3mmx3mm size grooves at junctions of two dissimilar materials. Providing 12mm thick plaster in two layer inside the building in cement mortar 1:6 on walls finished to a smooth finish as per specification. Providing 12mm thick plaster in cement mortar 1:6 on walls with rough finish as per specification. Providing 6mm thick plaster on celling in cement mortar 1:4 finished to a smooth as per specification. Forming groove of uniform size from 12x12 mm upto 20x15 mm in plastered surface as per approved pattern, using wooden battens nailed to the under layer, including removal of wooden batons, repair of the edges of plaster panel and finishing the groove etc. complete as per specification, drawing and the instructions of engineer in charge. Providing drip coarse on plastered surface at all elevations for all type of work such as chajjas, parapet, projections etc. including scaffolding, finishing etc. complete with all labour, tools and plants as per specification, drawing and instructions of engineer in charge. Providing Plaster of Paris/white putty (birla white) 2mm thick punning over finished plaster surface and finished with smooth surface as per specification. Sqm Sqm Sqm Sqm 8615 10279 3640 5080 UNIT Cum Cum Total Quantity 15 10 UNIT RATE (IN RS) AMOUNT RS) (IN
1012 1013 1100 1101
Cum Sqm
20 225
Sqm
389
1200
1201 1202 1203 1204
1206
RM
100
1207
RM
99
1209
Sqm
250
13
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1300 DESCRIPTION OF ITEM FINISHES, PAINTING TO CONCRETE, PLASTERED SURFACES, SURFACE PREPARATION INCLUDING ALL MATERIALS, LABOUR, SCAFFOLDING ETC. ALL COMPLETE AS PER SPECIFICATION, DRAWING AND AS DIRECTED BY ENGINEER FOR THE FOLLOWING: Two or more coats of white wash/colour wash as per IS:627 of approved brand and manufacture to give an even shade including a priming coat as per specifications. Two or more coats of exterior masonry paint (water or solvent base) of special resins, adhesives and additives mixed with fine, hard stone aggregate and finest available pigment. The paint shall be applied on a coat of primer over dried, prepared plaster surface as manufactures guidelines. The final finished coating shall be fungus resistant, UV resistant, water repellant, alkali resistant and extremely durable with color fastness as per specification. Providing and applying two or more coats of oil bound distemper as per IS:428 of approved brand, shade and manufacture to give smooth, hard, durable & glossy finish over a coat of primer over prepared plaster surface as per manufacturers guideline including plaster of Paris punning minimum 2 mm. Providing and applying two or more coats of acrylic emulsion paint as per IS:5411 of approved brand, shade and manufacture to give smooth, hard, durable & glossy finish over a coat of primer over prepared plaster surface as per manufactures guideline plaster of Paris punning minimum 2 mm. Providing and applying 3 coats of water proof cement paint of approved make and color on exterior surface at all heights including material, labour, scaffolding, curing etc including primer coat complete as per specification. Providing and applying resin bonded granular textured finish, for external application shall consist of crushed stone/quartz chips of .5 mm to 2.5 mm size and of approved natural color/shade and bonded with synthetic resins, adhesives and additives altogether in a single pack mix, applied on coured and dried plaster surface with a dry film thickness of minimum 2 mm. The final finish shall have UV resistance, fungus, bacterial resistance properties all complete with grooves filled with poly sulfide sealant of matching color and shade as per specification/drawing/approval of engineer in charge. Providing and applying 2 mm thick plaster of Paris punning on walls including preparation of surface, staging etc. to achieve a smooth even surface all complete as per specification and as directed by Engineer. NA FLOORING AND SKIRTING INCLUDING BASE LAYER AND ALL MATERIALS, LABOUR, CURING, POLISHING ETC. COMPLETE IN ALL RESPECTS AS SHOWN ON DRAWINGS, DESCRIBED IN SPECIFICATIONS AND AS DIRECTED BY ENGINEER FOR THE FOLLOWING: Providing and laying 50mm thick heavy duty cement concrete flooring with metallic hardener pigment topping of 12 mm thick uniform graded treated iron particles in flooring. Under layer of 38mm thick cement concrete mix 1:2:4 (1 part cement, 2 parts sand and 4 parts stone chips 12.5 mm well graded). Sqm Sqm UNIT Total Quantity UNIT RATE (IN RS) AMOUNT RS) (IN
1301 1302
400 1882
1303
Sqm
11433
1305
Sqm
2938
1310 1314
Sqm Sqm
304 4178
1315
Sqm
4000
1317 1400
1401
Sqm
15099
14
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1402 DESCRIPTION OF ITEM Providing and laying 50 mm thick heavy duty cement concrete flooring with metallic hardener pigmented topping of 12 mm thick uniform graded treated iron particles in skirting and dado. Under layer of 38mm thick cement concrete mix 1:2:4 ( 1 part cement, 2 parts sand and 4 parts stone chips 12.5 mm well graded ) and top layer of 12mm thick metallic concrete complete. Providing and laying precast polished heavy duty cement tiles (Caborundum) of size 300X300X25 thick of approved shade as per IS 1237, laid in floors and landings, jointed with neat cement slurry with pigment to match the shade of the tiles including, minimum 25 mm thick underbed of 1 part cement, 2 part sand : 4 parts stone chip by volume mixed with sufficient water to form a stiff workable mass and brought to proper level. The tiles laid over underbed, with cement mortar pressed and tapped down with wooden mallet to the proper level, lifted and pressed again with thick cement slurry spread over the surface with fine joint finished including pigments, curing, grinding, polishing etc. complete with laying as per IS:1443. Providing and laying interlocking M30 concrete blocks of thickness 60 mm as paving of approved colour and pattern and should be laid on the sub base and bedding as per specifications and recommendations of manufacturer. Providing and laying polished Kota stone 20 mm thk in flooring. Under bed shall average 30mm thk of 1 part cement,2 part sand : 4 parts stonechip by volume and brought to proper level. The kota stone slabs/tiles laid over under bed, pressed and tapped down with wooden mallet to the proper level, lifted and pressed again with thick cement slurry spread over the surface with fine joint finished including pigments, curing, grinding, granite polishing etc. complete. Providing polished Kota stone 20 mm thk in skirting projecting 6mm from adjacent plaster all complete . Providing and laying polished Granite stone of approved color and texture 20 mm thick in flooring. Under bed shall average 30mm thick of 1 part cement, 2 part sand : 4 parts stone chip by volume and brought to proper level. The granite stone slabs/tiles laid over under bed with cement mortar, pressed and tapped down with wooden mallet to the proper level, lifted and pressed again with thick cement slurry spread over the surface with fine joint finished including pigments, cutting, grinding, granite polishing etc complete. Providing and laying polished Granite stone 20 thick in skirting and dado including pigments, curing, grinding, granite polishing etc. complete. Providing and laying 7 mm thk vitrified ceramic tiles (Mat or Mirror) of size 400x400 from reputed manufacturer, complete as per specification. Providing and laying 7 mm thk vitrified ceramic tiles (Mat or Mirror) of size 600x600 from reputed manufacturer, complete as per specification. Providing and laying 7 mm thk vitrified ceramic tiles (mat or mirror) of size 400x400 from reputed manufacturer, for skirting and dado up to specified height complete as per specification. Providing and laying 7 mm thk vitrified ceramic tiles (Mat or Mirror) of size 600x600 from reputed manufacturer, for skirting and dado up to specified height complete as per specification. Providing and laying Heavy Duty dust pressed Ceramic Tiles of size 300X300X7 mm thick, GroupV conforming to IS:13755, of reputed manufacturer of approved finish shade and colour. UNIT Total Quantity 23 UNIT RATE (IN RS) AMOUNT RS) (IN
SQM
1403
Sqm
50
1405
Sqm
6250 329
1406
SQM
1407 1408
SQM Sqm
85 200
1409 1410 1411 1412 1413 1414
Sqm SQM SQM SQM SQM Sqm
145 1272 204 440 172 309
15
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1418 DESCRIPTION OF ITEM Providing & fixing chemical resistant (Acid & Alkali) bricks (75 mm thk) as per IS 4860 in the floor of neutralization pit. Surface on which lining has to be applied shall be prepared in accordance with IS 2395. Bitumen primer as per IS 158 followed by 18 mm thk Bitumuinastic followed by 6 mm thk potassium silicate mortar bedding shall be provided before laying AR bricks. The joints between AR bricks shall be filled with resin type of mortar confirming to IS 4832, Part II. Seal coat of readymade epoxy paint shall be provided on joints to cover up any porosity that may be left in mortar. End ceiling shall be done with bitumastic. A.R. bricks shall be laid with 6 mm wide and 20 mm deep pointing ( epoxy/furane/CNSL ) and acid curing shall be done complete as per specification. Providing and laying marble flooring/dado of minimum 20mm thickness projecting 6mm from adjacent plaster all complete including underbed mortar, labour, material, scaffolding, etc as per specification. Providing and laying granite stone slab of 12 mm thickness single piece for wash basin slab of black or approved colour with cutting and opening complete. Providing and laying granite stone slab of 20 mm thickness for platforms in pantry slab of black or approved colour with cutting and opening complete. Providing and laying glazed ceramic tiles of approved color and design in dado of approved size of reputed manufacturer topped with 50 mm wide matching ceramic trims, complete as per specification including all material, labour etc. 5 mm thick 7 mm thick Providing and fixing dividing strips in joints of cast in situ floorings at various elevations, finishing, all labour, material etc. complete as per drawing, specification and instructions of engineer in charge. Glass strips 40mm wide and minimum 6 mm thick Aluminum strips 40mm wide and minimum 3 mm thick Providing and laying wodden panel flooring and wall PERGO or equivalent all complete as per specification. Providing and erecting roofing/side cladding including laps, scaffolding hooks, washers, corner pieces, etc. cost of all material, labour, equipment, cleats, sheeting runner, rails mild steel wind ties (horizontal/vertical) and any other steel works etc. at all elevations complete as per specification, drawing and as directed by the engineer for the following: Designing, providing and fixing permanenently color coated (on exposed face) galvanized M.S. trough metal sheet decking plate of approved color over roof purlins for In-situ roof slab as per IS:14246. Thickness of deck plate shall be minimum 0.8mm and minimum trough depth of 38 mm with minimum yield strength of 250 Mpa. Silicon modified polyester paint shall be used for permanent coating over galvanized surface with minimum rate of galvanization 275 gm/Sqm. DFT of permanent color coating shall be 20 microns. It shall serve as permanent shuttering for roof slab 50 mm thk measured over crest of metal decking and 25 mm thick layer of screed concrete and a layer of 25 mm thick wearing course mortar over it. It should have adequate strength to support weight of green concrete and imposed load during concreting as well as in service condition of 150 kg/Sqm with purlin spacing of around 1400. UNIT Total Quantity 325 UNIT RATE (IN RS) AMOUNT RS) (IN
SQM
1420
51 SQM Sqm Sqm 50 64
1422 1423 1424 (i) (ii) 1425 (i) (ii) 1426 1500
Sqm Sqm
50 50
RM RM SQM
2770 500 90
1501
Sqm
4300
16
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1503 DESCRIPTION OF ITEM Design supply & erection of permanent colour coated thermally insulated sandwitched metal cladding for external wall with troughed galvanised MS sheeting of 0.6mm thickness and 275 g/sqm of galvanisation or Hi tensile steel (350 Mpa) 0.5 mm thick, coated with zinc aluminium alloy @ 150 g/sqm. Outer exposed face shall have silicon modified polyster coating of DFT 20 microns over primer having life span sustenance against weathering action, inner sheeting shall have 7 micron of precoating, sandwitched Insulation of minimum 50 mm thick bonded mineral wool blanket conforming to IS:8183 (minimum density of 32 kg/cum for glass wool and 48 kg/cum for rock wool or 40-45 kg/cum for polyuretene foam (fire retardants and non-toxic) confirming to IS:12436, cladding shall be fixed to supports/rails by concealed fixing system with corrosion resistant self tapping/self drilling type fasteners provided with suitable cap. Flashing shall have the same material and minimum overlap of 100 mm. Flashing shall not be paid separately. Design supply & erection of permanent colour coated non insulated metal cladding for extemal walls toughed galvanized MS sheeting of 0.6mm thickness and 275 g/Sqm of galvanization or Hi tensile steel (350 Mpa) 0.5 mm thick, coated with zinc aluminum alloy @ 150 g/Sqm. Outer exposed face shall have silicon modified polyester coating of DFT 20 microns over primer having life span sustenance against weathering action, inner side shall be coated with same paint of minimum DFT 20 microns over primer. Cladding shall be fixed to supports/rails by concealed fixing systems with corrosion resistant self tapping/self drilling type fasteners provided with suitable cap. Flashing shall have the same material and minimum overlap of 100 mm. Flashing shall not be paid separately. Providing 50 mm thick fibre glass under deck insulation having min. density 24kg/cum with 0.05 mm thick aluminium foil & 0.6 mm x 25mm mesh wire netting and shall be fixed to the ceiling with 2 mm wire ties. all complete as per specifications and drawings. Providing, fixing and laying permanently colour coated aluminum false ceiling approved colour and Luxalon make or approved equivalent (Type-84C, Interior) with corrosion resistant aluminum alloy panels of minimum thickness 0.5 mm including 50 mm thick mineral wool insulation (as per IS:8183) bound in polythene bags on top of panels. Additional hangers and height adjustment clips shall be provided above the false ceiling level for movement of personal to facilitate maintenance of lighting fixtures, AC ducts etc. Providing and Fixing 12mm thick Gypsum plaster board for false ceiling conforming to IS:2095 approved make in plan or elevation with aluminum grid, metal suspension system, anchor fastener adjustable hangers, etc. all complete with smooth finish as per specification, drawing and as directed by Engineer. Providing and fixing rain water down take pipes including 2 coats of approved paint over a primary coat, all specials and accessories etc. complete as per specification. HCI down take pipes of 150mm dia as per specifications Galvanised MS down take pipes of 150 mm dia-Medium quality as per IS:1239 (part-I)/IS:3589 with welded joints MISCELLANEOUS Providing and fixing PVC water stops - 225 mm wide UNIT Sqm Total Quantity 4200 UNIT RATE (IN RS) AMOUNT RS) (IN
1504
Sqm
2405
1601
SQM
500
1602
Sqm
1638
1604
Sqm
50
1700
1703 1706 1800 1801
RM RM Sqm
512 420 320
17
BAWANA-PRAGATI/CIVIL PART/784
Page 15 of 26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1804 1805 1810 1811 DESCRIPTION OF ITEM Providing and fixing bitumen impregnated fiber joint filling board of 25 mm thickness, fillers along with PVC water bar etc for expansion joint in water retaining structures all complete as per specifications, drawing and as directed by Engineer. Supply and laying of rounded gravels 40mm thick in transformer yards etc. as directed by Engineer. Providing, laying and fixing transformer rails including guide rails in concrete including joining of rails, anchoring lugs etc complete as per specifications and as directed by Engineer. Laying of earthing mats/rods including transportation from yard stores, loading, unloading, cutting to length, welding etc complete as per specification and as directed by Engineer. Providing removable metallic false flooring system with nominal height of the false flooring 600 mm. The same shall comprise of special grade steel panels (of size 600x600mm). without any dimensional tolerance 1.2mm thick die cast to shape having 1mm thick top MS sheet spot welded together to form a composite steel panel, sitting on aluminum diecasted heads & mounted on steel pedestals of 25mm dia rod of adjustable height and supporting 1.2mm thick channel frame work at-top and 2mm thick 150x150mm base plate. The top finish shall be 2mm thick antistatic PVC sheet or High pressures laminate. Cavity area below the false flooring shall be made dust proof by using Polyurethane paint. Designing, providing and fixing of Heavy duty galvanised friction anchor fasteners of Hilti/Equvalent make of dia, 16 mm and appropriate length in concrete (minimum grade M30) to take direct tension of minimum 1.8 Mton including anchor fasteners, materials, equipment, labour, scaffolding, complete as direction of Engineer. Designing, providing and fixing of Heavy duty galvanised friction anchor fasteners of Hilti/Equvalent make of dia, 20 mm and appropriate length in concrete (minimum grade M30) to take direct tension of minimum 1.8 Mton including anchor fasteners, materials, equipment, labour, scaffolding, complete as direction of Engineer. Designing, providing and fixing of Heavy duty galvanised chemical anchor fasteners of Hilti/Equvalent make of dia, 12 mm and appropriate length in concrete (minimum grade M30) to take direct tension of minimum 1.0 Mton including anchor fasteners, materials, equipment, labour, scaffolding, complete as direction of Engineer. Designing, providing and fixing of Heavy duty galvanised chemical anchor fasteners of Hilti/Equvalent make of dia, 16 mm and appropriate length in concrete (minimum grade M30) to take direct tension of minimum 1.6 Mton including anchor fasteners, materials, equipment, labour, scaffolding, complete as direction of Engineer. Providing and fixing GI rungs in concrete/brick wall at all elevation including @ zinc coating shall not be less than 900 g/Sqm all complete. UNIT RM Cum MT MT Total Quantity 235 150 20 50 60 UNIT RATE (IN RS) AMOUNT RS) (IN
1812
SQM
1813
Nos.
20
1814
Nos.
20
1815
Nos.
20
1816
Nos.
20
1819
KG
410
18
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 1820 DESCRIPTION OF ITEM Design, supply, fabrication, erection of stoplog gates in CW Pumps as per specification with embedments required, lifting beams, special tools & plants, spare parts for three years, machining, casting, all materials such as structural steel, cast steel, stainless steel, brass used for seals, rubber seals, gears, ball and roller bearing, branch bushings, greasing, bolts, nuts, lugs, threaded fastners etc., cleaning, sand blasting, hot double dip galvanised with minimum coating of zinc 750 gms/sqm., following by an application of etching primer and dipping in black bitumen as per B.S. 3416, erection along with a second stage concreting to true plumb and levels, submission of drawings / fabrication drawings for engineers approval etc., all complete as per specifications and approved drawings. The leakage through rubber seal shall not be more than 5 lit/min/metre length of seal under maximum head.(only weight of structural steel including embedments shall be considered for payment purpose) UNIT Total Quantity 21 UNIT RATE (IN RS) AMOUNT RS) (IN
MT
1821
Supplying, fabricating, erecting in position and testing / examining bolted and / or welded structural steel work at all levels for stationary screens made out of rolled sections and / or plates including cutting, straightening if required, edge preparation, bolting / welding of joints, cleaning, sand blasting, hot double dip galvanised with minimum coating of zinc as 750 gms./sqm. followed by application of an etching primer and dipping in black bitumen as per BS 3416, complete as per drawing and directed.
10 MT
2000 2001 2002
FENCING AND GATES Supplying and fixing G.I. barbed wire in fencing including G.I. clips etc. complete as per specification. Supply, fabrication and installing in position and testing galvanised MS Gates out of channels, joints, angles, flats, plates, pipes & sheets including stiffeners, bracings, fabricated hinges, MS Aldrops with locking arrangement, tempered steel pivot, guide track of MS Tee, ball bearing arrangements, castor wheels, etc. all complete as per drawing, specification and as directed by Engineer-in-charge with 600 mm high GI barbed wire fencing at top all complete. Supplying and erecting in position fencing, with gate, shall comprise of PVG coated G.I. welded wire mesh fencing of minimum 4 mm diameter (including PVC coating) of mesh size 75mmX75mm of height 2.4 above the toe wall with a 600 mm high galvanised concertina at the top, total fence height of 3.0 m above the toe wall. The diameter of the steel wire for chain link fence (excluding PVC coating) shall not be less than 2.5 mm. The tensile serrated galvanised wire (HTSW) concertina made with wire diameter of 2.5 mm diameter by means of clips at 1m intervals. These two HTSSW strands will be attached to the fence posts with 12 mm security fasteners. All nuts, bolts, fasteners, clamping strips, clamps, clips, etc., shall be galvanised. The toe walls of brick masonry with plastering, painting, fence posts with 75X75X6 MS angles spaced at 2.5 m c/c with suitable RCC foundations, complete as per specificay. etc. MT MT 8 14
2003
Sqm
1776
2100 2101
WATER SUPPLY Providing and fixing in position tested heavy duty type chromium plated brass long neck bib cocks including sockets, union, nut etc complete - 15 mm nominal bore.
Nos.
42
19
Page 17 of 26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2102 DESCRIPTION OF ITEM UNIT Nos. Nos. Nos. RM Total Quantity 42 36 21 455 UNIT RATE (IN RS) AMOUNT RS) (IN
Providing and fixing in position heavy duty brass stop cock of approved quality including all specials etc complete as directed by Engineer - 15mm nominal bore. 2103 Providing and fixing in position heavy duty brass full way value with wheel of approved quality 25 mm nominal bore. 2104 Providing and fixing in position heavy duty brass full way value with wheel of approved quality 50 mm nominal bore. 2105 Providing and fixing GI pipes Class B medium class conforming to IS:1239 pipes shall be concealed and painted with anti-corrosive paint, complete with GI sockets, union, elbows, tees, nipples etc and clamps including cutting and making good the walls etc complete - 15 nominal bore. 2106 Providing and fixing GI pipes class B medium class conforming to IS:1239 pipes shall be concealed and painted with anticorrosive paint, complete with GI sockets, unions, elbows, tees, nipples, etc. and clamps including cutting and making good the walls complete 20 mm nominal bore. 2107 Providing and fixing GI pipes class B medium class conforming to IS:1239 pipes shall be concealed and painted with anticorrosive paint, complete with GI sockets, unions, elbows, tees, nipples, etc. and clamps including cutting and making good the walls complete 25 mm nominal bore. 2108 Providing and fixing GI pipes class B complete with GI sockets, unions, elbows, tees, nipples, etc. including trenching & refilling, anti-corrosive paint etc. all compete (for external work) - 15 mm bore (N.B). 2109 Providing and fixing GI pipes class B complete with GI sockets, unions, elbows, tees, nipples, etc. including trenching & refilling, anti-corrosive paint etc. all compete (for external work) - 20 mm bore (N.B). 2110 Providing and fixing GI pipes class B complete with GI sockets, unions, elbows, tees, nipples, etc. including trenching & refilling, anti-corrosive paint etc. all compete (for external work) - 25 mm bore (N.B). 2111 Providing and fixing GI pipes class B complete with GI sockets, unions, elbows, tees, nipples, etc. including trenching & refilling, anti-corrosive paint etc. all compete (for external work) - 50 mm bore (N.B). 2112 Providing and fixing 600mmx450mmx5.5mm thick float glass mirror with beveled edge from reputed mirror manufacturer. Miorr shall be mounted with glass adjustable revolving CP brackets, etc. complete with CP screws as per specification. 2112-a Providing and fixing 5.5mm thick wall float glass mirror with minimum height of 900 mm reputed mirror manufacturer. Miorr shall be mounted with glass adjustable CP brackets, etc. complete with CP screws as per specification. 2113 Providing and fixing 610mmx127mmx6mm thick clear glass shelf with CP Guard rails and mounted on CP brackets, etc. complete as per specification. 2114 Providing and fixing 25mm dia stainless steel towel rails (600 mmx20 mm) complete as per specification. 2115 Providing and fixing stainless steel soap folder cum dispenser complete as per specification. 2116 Providing and fixing CP liquid soap dispenser. Dispenser shall be round and easily removing with removable threaded nozzle and mounted on C.P. brackets etc. complete as per specification.
RM
250
RM
250
RM RM RM RM No. No. No. No. No. No.
505 335 320 146 36 12 31 34 47 50
20
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2117 DESCRIPTION OF ITEM Providing & fixing P.V.C. water tank of 1000 liters capacity (Syntax or approved equivalent make) in position. The worked to include making all necessary inlet & outlet pipes, fixture, ball cocks, valves etc all complete as per specification and at all heights and levels. Providing & fixing P.V.C. water tank of 2000 liters capacity (Syntex or approved equivalent make) in position. The worked to include making all necessary inlet & outlet pipes, fixture, ball cocks, valves etc all complete as per specification and at all heights and levels. Providing & fixing P.V.C. water tank of 5000 liters capacity (Syntex or approved equivalent make) in position. The worked to include making all necessary inlet & outlet pipes, fixture, ball cocks, valves etc all complete as per specification and at all heights and levels. Providing and fixing glazed vitreous wall mounted paper holder with suitable cover cum cutter fitted with CP screws etc. complete as per specification. Providing and fixing chromium plated brass shower rose with 15 or 20 mm inlet all complete. Providing and fixing approved stainless steel sink with integrated drain board complete including painting the fittings, cutting and making good the wall where required as per specification. The work to be complete as per specifications, drawing and direction of engineer. SANITARY WORKS Supplying and fixing Wash basin (oval shape) with photo-voltaic control fittings as per IS:2556 to be fixed on concrete platform finished and under fixed with 20mm thick polished granite stone as per specifications and directed by engineer. Providing and fixing approved vitreous china acid/alkali resistant laboratory sink of size 600X400X200mm conforming to IS:2556 (Part 5) complete including painting the fittings, cutting and making good the wall where required as per specification. Providing and fixing stainless steel kitchen sink of size 610X510X200 as per IS:13983 and specifications. Providing and fixing European WC as per IS:2556 with all fittings including photo-voltaic sensor operated flushing system of appropriate capacity and type, complete as per specification and directed by Engineer. Providing and fixing WC (Indian type, Orison pan (580 X 440 mm) as per IS:2556 with all fittings including photovoltaic sensor operated flushing system of appropriate capacity and type, complete as per specification and directed by Engineer. Providing and fixing wall type glazed vitreous china urinals with photo voltaic control flushing system as per IS :2556 with flush pipes, lead pipes, grating, traps and necessary C.P. brass fittings all complete as per specifications. Supply, laying and jointing 75 mm dia heavy duty cast iron pipes including bends, branches and all other necessary fittings lead caulking, a coat of bituminous paint, M.S. holder bats/clamps, cutting and making good the walls and floors, jointing, testing, etc. all complete as per specifications. Supply, laying and jointing 100 mm dia heavy duty cast iron pipes including bends, branches and all other necessary fittings lead caulking, a coat of bituminous paint, M.S. holder bats/clamps, cutting and making good the walls and floors, jointing, testing, etc. all complete as per specifications. UNIT No. Total Quantity 12 UNIT RATE (IN RS) AMOUNT RS) (IN
2118
No.
2118A
No.
2119 2120 2121
No. No. No.
5 5 12
2200 2201 2202 2202a 2203 2204 2205 2206
No. No. No. No. No. No. RM
35 9 8 27 5 29 640
2207
RM
224
21
Page 19 of 26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2208 DESCRIPTION OF ITEM Supply, laying and jointing 150 mm dia heavy duty cast iron pipes including bends, branches and all other necessary fittings lead caulking, a coat of bituminous paint, M.S. holder bats/clamps, cutting and making good the walls and floors, jointing, testing, etc. all complete as per specifications. Providing, laying light duty non-pressure NP3 class RCC pipes with collars jointed with stiff mixture of cement mortar 1:2 including testing of joints etc. complete-200 mm dia, as per specification. Providing, laying light duty non-pressure NP3 class RCC pipes with collars jointed with stiff mixture of cement mortar 1:2 including testing of joints etc. complete-300 mm dia, as per specification. Providing, laying light duty non-pressure NP3 class RCC pipes with collars jointed with stiff mixture of cement mortar 1:2 including testing of joints etc. complete-450 mm dia, as per specification. Providing, laying light duty non-pressure NP3 class RCC pipes with collars jointed with stiff mixture of cement mortar 1:2 including testing of joints etc. complete-600 mm dia, as per specification. Providing, laying light duty non-pressure NP3 class RCC pipes with collars jointed with stiff mixture of cement mortar 1:2 including testing of joints etc. complete-800 mm dia, as per specification. Providing and fixing C.I. Manhole cover of size 600mmx450mm including frame from reputed manufacturer all complete as per specification. Providing and fixing C.I. Manhole cover of size 450mmx450mm including frame from reputed manufacturer all complete as per specification. Providing and fixing C.I. Manhole cover of size 750mmx750mm including frame from reputed manufacturer all complete as per specification. Providing and fixing circular heavy duty C.I. manhole cove of 600 mm dia with frame all complete as per specification. Providing and fixing square mouth S.W Gully trap grade 'A' complete with CI grating, brick masonry chamber and water tight CI cover with 300X300mm (inside) the weight of cover to be not less than 4.53 Kg and frame to be not less than 2.72 Kg as per drawing and specifications etc all complete size - 100X100 mm P or S type Providing and fixing square mouth S.W Gully trap grade 'A' complete with CI grating, brick masonry chamber and water tight CI cover with 300X300mm (inside) the weight of cover to be not less than 4.53 Kg and frame to be not less than 2.72 Kg as per drawing and specifications etc all complete size - 150X100 mm P or S type Providing and fixing square mouth S.W Gully trap grade 'A' complete with CI grating, brick masonry chamber and water tight CI cover with 300X300mm (inside) the weight of cover to be not less than 4.53 Kg and frame to be not less than 2.72 Kg as per drawing and specifications etc all complete size - 150X150 mm P or S type Construction of road/yard gullies in 250TH brickwork - 750mm deep with cement concrete M-20 grade foundation, including reinforcement, 12mm cement mortar (1:3) plastering both inside and outside, M.S. rugs @ 250 c/c, C.I. Grating along with frames as per IS standers including necessary earthwork in excavation, backfilling etc complete as per drawings/specifications. Providing and fixing cinder C.I. floor traps with C.P jali complete as per specification. Providing and laying cinder filling in the toilets complete as directed by engineer in charge. UNIT RM Total Quantity 235 UNIT RATE (IN RS) AMOUNT RS) (IN
2209 2210 2211 2212 2213 2219 2219a 2219b 2220 2221
RM RM RM RM RM Nos. Nos. Nos. Nos. Nos.
1730 640 245 210 100 71 32 28 10 50
2222
Nos.
49
2223
Nos.
55
2224
Nos.
14
2225 2226
Nos. CUM
50 5
22
Page 20 of 26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2227 DESCRIPTION OF ITEM Construction of RCC manholes with cement concrete M-20 grade circular upto dia 1200 mm or square of size upto 100mmX100mm and upto 3000 mm deep including necessary earthwork in excavation, backfilling, lean concrete M7.5 (excluding manhole covers which are to be paid separately under separate under separate item), with M.S. rungs @ 250 c/c all complete as per drawings and specifications. Providing and installing approved brand single tap water cooler of 80L cooling capacity complete in all respect. Providing and installing approved brand single tap water cooler of 150L cooling capacity complete in all respect. Providing and installing hand dryers. Providing and fixing vitreous urinal partitions all complete as per specification. STRUCTURAL STEEL WORKS ALL items for fabrication should include supply, fabrication, errection, preparation of fabrication drawings, as per specifications including painting with a coat of primer and also inclusive of all necessary quality test to the satisfaction of engineer/customer for the following. Supply, Fabrication, erection, alignment, welding, primer painting (primer coat consisting of 3 coats of red oxide zinc-chromate (total DFT 75 Microns) as per IS:2074 & IS:1477 (Parts I & II). One coat to be applied at shop and other two after erection) of structural steel made from Mild Steel (Rolled Sections and Plasters) shall conform to Grade 'A' of IS:2062 for thickness upto and including 20mm and shall conform to Grade 'B' of IS:2062 for thickness beyond 20mm thickness. Medium and High Strength steel shall confirm to grade 'Fe490B' of IS:8500 or equivalent. Rolled Sections and Plates up to and including 20mm thickness shall be semi-killed condition. Plates beyond 20mm thickness shall be killed condition. All steel upto and including 40mm thickness shall be in as Rolled condition. Plates beyond 40mm thickness shall be Normalised and Ultrasonically tested. Pipes shall conform to IS:1161 Hollow (square and rectangular) Steel Sections shall be Hot Formed conforming to IS:4923 and shall be of Minimum grade Yst 240. Chequered Plate shall conform to IS:3502 and shall be minimum 6mm thick excluding projection, Steel for chequered Plates shall conform to Grade 'A' of IS:2062, at all elevations involving rolled sections (including mild steel rounds), built up sections fabricated out of plates, rolled sections and combination of plates and rolled sections, in columns, beams, gantry girders, silos, roof trusses, portals, laced purlins, space frames, shear connectors, hangers, struts, monorails, galleries, stiffeners, wall beams, sheeting runners, brackets, stub columns, bracings, cleats, trestles, base plates, chequered plate flooring, decking and seal plates, diaphragm, steel frame grid over false ceilling, walkway platforms, ladders, stairs, stringers, treads, landings, toeplates, MS Rungs, insert plates, edge angles, embedments, lugs, posts, stays, louves, lacings, gusset plates, safety chains for walkways adjacent to crane griders etc, collection of steel from stores, transportation, straightening, making cutting plan, cutting, bending, rolling, grinding, drilling, botling, erection bolts & nuts (weight erection bolts & nuts not payable, supply of permanent bolts of grade C mild steel bolts & nuts to be paid separately under ST NO. 2309 (i), assembly, edge preparation, preheating (minimum preheat and interpass UNIT Nos. Total Quantity 10 UNIT RATE (IN RS) AMOUNT RS) (IN
2228 2229 2230 2231 2300
No. No. No. No.
2 2 3 10
2301
MT
117
23
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO DESCRIPTION OF ITEM Prepared by the bider and all other activities required for completetion of the work including return of surplus/waste steel materials to store etc. as per specification, drawings and instructions of the Engineer. Approval of fabrication drawings does not relieve the bidder from the responsibility of its correctness and accuracy. Fabrication along with one coat of primer (50% of quoted rate) Erection Alignment & welding Primer UNIT Total Quantity UNIT RATE (IN RS) AMOUNT RS) (IN
a.) b.) c.) d.)
MT MT MT MT
1200 2700 3250 4400
2301a
2301c
Extra over ST NO. 2301 for blast cleaning of steel structures to near white metal surface(Sa 2 1/2 ) and applying epoxy based zinc phosphate primer in coats of minimum 25 micron (DFT) at shop and 50 micron (DFT) after erection, instead of primer coat of red oxide zinc-chromate, including touch-up painting etc complete as per specification. Providing & application of anti corrosive synthetic enamel paint of Berger or approved equivalent make and colour in three coats of 25 micron thickness (DFT) per coat already having primer coats (as per ST NO. 2301) at all elevations to achieve an even shade with all materials, labour, equipment, handling, including protection and cleaning, scaffolding etc. complete as per specification, drawings and instructions of the Engineer. (Total thickness (DFT) including primer shall not be less than 100 micron. NA Supplying, fabrication, transportation, erection and alignment of factory made electroforged gratings 40 mm thick with steel conforming to IS:2062 at all elevations including preparation of design drawings and fabrication drawings in flooring, platforms, drain and trench covers, walkways, passages, staircases with edge binding strips and anti-skid nosing in treads, fixing clamps etc. complete with other fittings and fixtures including all taxes, duties, transpiration, packing, grinding, drilling, bolting (supply of permanent grade 'C' mild steel bolts and nuts to be paid separately under ST NO. 2309(i)), all welding, edge preparation, blast cleaning of steel surfaces to near white metal surface (Sa 2 1/2) and shall be hot dip galvanised at the rate of 610 gm/sqm, complete as per specifications, drawings and instructions of the Engineer. Supply, fabrication and delivery at site, transportation, loading/unloading of various sizes, GI pipe hand railing (1000 mm high) of 50 mm dia (Medium Grade) including painting and fixing, confirming to IS:1161 as per specification, labour and material complete for heavy duty class. Supply, fabrication and delivery at site, transportation, loading/unloading of hand railing with 20mm square MS bar balustrades with suitable MS flats and aluminum hand rail.
MT
110
MT
4514
2302 2303
MT
75
2304
MT
13
2305
MT
24
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2309 DESCRIPTION OF ITEM i) Supplying and fixing in position of permanent mild bolts (class 4.6 as per IS:1367 and grade 'C' as per IS:1363) and nuts, washers etc. washers etc. up to and inclusive of 39 mm diameter and upto 300 mm long of structural steel work complete as per specification, drawings and instructions of the Engineer. ii) Supplying and fixing in position of high strength structural bolts (of property class 8.8 and product 'C' as per IS:1367) and conforming to IS:3757 and high strength structural hardened and tempered nuts (of property class ' 8 ' as per IS:1367) conforming to IS:6623 with hardened and tempered washers as per IS:6649 etc. up to and inclusive of 39 mm diameter and upto 300 mm long for structural steel work complete as per specification, drawings and instructions of the Engineer Dismantling of steel structure at any elevation, lowering of material and carriage of the dismantled up to field fabrication shop, or, return to projects storage including temporary dismantling, cutting, re-welding, supporting, and restoring to correct positions, (weight of such adjustment members and temporarily dismantled members not payable) including scaffolding, staging, tools & trackless, gas cutting, welding, consumables, etc complete as per specification drawings and instructions of the Engineer. Addition to, alterations in and/or modification of "Erection Marks" either in erected position or in the shop including cutting of parts, gouging of welds, cutting, grinding, fabrication, welding, drilling holes, straightening, removal of bends, raising to the required level, painting, transportation, return of unutilized steel pieces to the project store, temporarily dismantling, cutting, re-welding, supporting and restoring to correct position of all the temporarily dismantled members, realignment of adjacent connected members, (weight of such temporarily dismantled and adjacent members not payable), complete as per specifications, drawings and instructions of the Engineer. i) In erected position ii) In fabrication yard Re-erection of dismantled fabricated structural steel members requiring additions, modifications, (dismantling and additions to, alterations in and/or modification to be paid separately under ST NO. 2310 abd 2310a respectively) including carriage of modified "Erection Marks" from the field fabrication shop to erection site, lifting to required position, aligning in position ,tack welding, final welding and touch up painting including temporary dismantling and re-erection of temporarily dismantled members, re-alignment of adjacent connected members, (weight of such temporarily dismantled members and adjacent member not payable) including scaffolding, staging, tools & trackless, gas cutting, welding, consumables, etc complete as per the specifications, drawings and instructions of the Engineer. Supply, fixing and placing of poly tetra floor ethylene bearing of reputed manufacturer for loading as specified below and displacement of (+) 50mm, complete with fixtures as per specification. i) Vertical Load of 20 Tons ii) Vertical Load of 30 Tons iii) Vertical Load of 50 Tons Nos. Nos. Nos. 15 15 2 MT MT MT 7 7 20 UNIT Quintal Total Quantity 15 UNIT RATE (IN RS) AMOUNT RS) (IN
Quintal
10
2310
MT
10
2311
2312
2317
25
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2319 DESCRIPTION OF ITEM Conducting radiography test on welds wherever specified by engineer including provision of necessary equipments, measuring devices, gauges, materials and labour as per specifications complete (over and above the work already specified in the specifications) Conducting ultrasonic test on welds wherever specified by engineer including provision of necessary equipments, measuring devices, gauges, materials and labour as per specifications complete (over and above the work already specified in the specifications) Conducting magnetic particle test on welds wherever specified by engineer including provision of necessary equipments, measuring devices, gauges, materials and labour as per specifications complete (over and above the work already specified in the specifications) Conducting dry penetration test on welds wherever specified by engineer including provision of necessary equipments, measuring devices, gauges, materials and labour as per specifications complete (over and above the work already specified in the specifications) ROAD WORK Preparation of sub grade by excavating earth to required depth for all type of soil/ rock, dressing to camber and consolidating the base including making good the undulation etc. and disposal of surplus earth within plant boundary in accordance with IS:2720 all complete as per specification. UNIT RM Total Quantity 50 UNIT RATE (IN RS) AMOUNT RS) (IN
2320
RM
50
2321
RM
50
2322
RM
60
2400 2401
CUM
28000
2402
Supplying and filling with selected good earth of approved quality and pavement and shoulders etc. in compacted layers of maximum depth 200 mm including watering, rolling/consolidating and dressing etc. to required camber including transportation, royalties complete. Providing and laying interlocking M30 concrete blocks of thickness 75 mm as per paving for shoulders of approved colour and pattern and should be laid on the sub base and bedding as per specifications and recommendation of manufacturer. Providing and laying water bound macadam base/sub base course in layers of required thickness with stone aggregate 90 mm to 40 mm down size stone screening and bending material including screening, sorting, spreading to template and consolidation with road roller including carriage of spreading and consolidation of blinding material morum etc. including cost of material, labour, all complete Providing and laying water bound macadam base/sub base course in layers of required thickness with stone aggregate 63 mm to 40 mm down size stone screening and bending material including screening, sorting, spreading to template and consolidation with road roller including carriage of spreading and consolidation of blinding material morum etc. including cost of material, labour, etc. all complete as per specification.
CUM
2100
2403
CUM
1476
2404
CUM
4800
2405
CUM
5300
26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2406 DESCRIPTION OF ITEM Laying water bound macadam wearing course with stone aggregate 50 mm to 20 mm size stone screening and binding material including screening, sorting, spreading to template and consolidation with road roller including carriage of spreading and consolidation of blinding material morum etc. including cost of material, labour, etc. all complete as per specification. Providing and applying Track coat of low viscosity liquid bitumen of suitable approved conforming to IS:73, 217 or 454 as applicable @ 10 KG/10 Sqm for an untreated WBM surface including scraping, cleaning with compressed air etc. complete. Providing and mixing laying of compacted 75 thk. Bituminous Macadam Course. Bitumen shall be of a suitable grade complying with IS:73 and aggregates, binder material as specified in specification including hot mixing, hot laying, rolling all complete. Providing, mixing and laying premix carpet (as per IRC-14) of compacted 50 mm thickness in a 2 layers of 25 each (first layer shall be provided during construction and second layer after commissioning of plant) composed of suitable small size aggregate premixed with a bituminous binder on a prepared base. Mixing applying rolling as per IRC specification. Providing and applying liquid seal coat comprising of an application of a layer of bituminous binder at the rate of 9.8kg/10sqm followed by a cover of stone chips at the rate of 0.09 cum/10 sqm followed by a cover of stone chips at the rate of 0.09 cum/10 sqm including rolling as per specification all complete. Providing & laying edge protection on both edges of black topping using brick on edge (bricks with crushing strength of 75 kg/cm2) with full brick width (230 mm) etc including fixing in 13mm thk. Cement mortar 1:6 complete. Supplying and laying edge protection on both edges of black topping using (400mmX150mmX350mm deep) precast concrete blocks / kerb stone of grade M25 with 20 mm aggregate and of shape as per detailed drawing including fixing in 13 mm thk. Cement mortar 1:2 in joints, finishing of joints with neat cement paste, making drainage opening where required etc. complete as per specification Supplying and laying edge protection on both edges of black topping using precast concrete blocks / kerb stone of grade M25 with 20 mm aggregate and of shape as per detailed drawing including fixing in 13 mm thk. Cement mortar 1:2 in joints, finishing of joints with neat cement paste, making drainage opening where required etc. complete as per specification. Dismantling of existing road consisting of premix, carpet, curb stone/brick on edge, bitumen macadam course, WBM, preparing sub grade to receive new WBM including camber consolidation including disposal of debris within a lead of 1 Km etc. complete and as directed by Engineer. Providing 25mm thick premix carpet on existing/damaged road surfaces (as per IRC-14) of compacted 25 mm thickness in a single course composed of suitable small size, aggregate premixed with bituminous binder on the existing base including tack coat, cleaning of existing surface, mixing applying rolling as per IRC specification. Concrete of grade M-30 in roads etc complete with 20 mm nominal size graded aggregate complete as per specification. Providing and laying concrete of grade M10 as lean concrete with 40 mm nominal size graded aggregate in shoulders complete as per specification. UNIT CUM Total Quantity 2800 UNIT RATE (IN RS) AMOUNT RS) (IN
2407 2408
Sqm Sqm
38186 38186
2409
Sqm
38186
2410
Sqm
38186
2411 2412
RM RM
5000 4016
2413
CUM
40
2414
Sqm
200
2415
Sqm
200
2416 2418
CUM CUM
150 50
27
Page 25 of 26
TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784 ITEM NO 2500 2501 DESCRIPTION OF ITEM PILING WORK Breaking pile head ( for 600mm diameter piles )to cut off level and exposing pile reinforcement for embedment in pile cap, etc. all complete as per specification, drawings and Disposal of pile debris beyond a lead of 3 KM and upto 5 KM as directed by engineer-in-charge. Developement of bored RCC cast in situ vertical pile with 600 mm concrete M25 grade conforming to IS:456 with 20 mm nominal size minimum cement content of 400 kg per cum of concrete including wherever required, all complete as per specification, drawings and charge. 2505 dia meter using cement stone aggregates with a materials,shuttering etc. directed by engineer-inUNIT Nos. Total Quantity 200 UNIT RATE (IN RS) AMOUNT RS) (IN
Rm
100
a. b. 2506
Conducting routine load test on job pile in accordance with IS:2911 (Part-4) including necessary excavation, all arrangements of loading, unloading, test equipments and accessories, jacks, recording of results, all materials, labour, submission of test report etc. but excluding the cost of installation of job pile complete as per specification, drawing and as directed by the engineer-incharge for the following for lateral load :- 600 mm dia piles-5.5 MT safe load capacity. For vertical(compression) load:-600 mm dia piles-110 MT safe load capacity. Carrying out low strain pile integrity test on job pile/test pile of 600 mm dia including all arrangements for tests, equipments and accessories, materials, labour, submission of test report etc. but excluding the cost of installation of job pile/ test pile complete as per specification and as directed by the engineer-in-charge. TOTAL
Each Each Each
2 2 200
NOTES: 1 In case of omission in quoting any rate, the evaluation will be done considering the highest quoted rate obtained against that item but the work, if awarded, will be on the lowest quoted rate obtained against that item. The rate shall be entered in figures as well as in words. In case of difference in rates between words and figures, the lesser of the two will be treated as valid rate. The bidders shall enter both Unit Rate & Amount. In case of any mismatch between Total Amount based on Unit Rate & Total Amount as quoted, the higher of the two shall be considered for evaluation and the lower of the two shall be considered for award. The quantities indicated against each item above are tentative and are liable to vary depending upon the site requirement. The contractor has to supply / install actual quantities as per advice of BHEL Engineer and accordingly the final contract price shall be worked out. Evaluation of the bids shall be done based on total price against this BOQ.
2 3
28

Bawana BOQ

Uploaded by

Copyright:

Available Formats

Bawana BOQ

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bawana BOQ

Uploaded by

Copyright:

Available Formats

FOR OFFICIAL USE ONLY NOT FOR PUBLICATION

TENDERERS COPY ORIGINAL COPY

TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784

PART II PRICE BID

Bharat Heavy Electricals Limited

TENDER NO. BHEL/NR/SCT/BAWANA-PRAGATI/CIVIL PART/784

THIS TENDER SPECIFICATION ISSUED TO: M/S-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

201 202 203 205

100 SQM Cum 500

300 301 304 307

(i) (ii) (iii) 400

Nos. Nos. Nos.

403 404 500 501 502

503 504 505

Cum Cum Sqm

604-a 604-b 604-c 700 701

(i) (ii) (iii) (iv) (v) 800 804

906 907 908

918 919 921 921 a

Sqm Sqm Nos. Nos.

(i) (iii) 1002

i) iii) iv) 1004

Cum Cum Sqm

1012 1013 1100 1101

1201 1202 1203 1204

1409 1410 1411 1412 1413 1414

Sqm SQM SQM SQM SQM Sqm

145 1272 204 440 172 309

51 SQM Sqm Sqm 50 64

1703 1706 1800 1801

512 420 320

2000 2001 2002

RM RM RM RM No. No. No. No. No. No.

505 335 320 146 36 12 31 34 47 50

2119 2120 2121

No. No. No.

2200 2201 2202 2202a 2203 2204 2205 2206

No. No. No. No. No. No. RM

RM RM RM RM RM Nos. Nos. Nos. Nos. Nos.

1730 640 245 210 100 71 32 28 10 50

2228 2229 2230 2231 2300

No. No. No. No.

a.) b.) c.) d.)

1200 2700 3250 4400

Each Each Each

You might also like