EMCTEST REPORT 2 Page 1 of 45 Report No| NSL-160714010204-R Applicant || Wuxi Sans Electronic Co., Ltd Industrial Wui, DongGang Town, Wuxi City, Jiangsu Province, China Product | Li-ion Battery Charger SSLC1OSV55 Specification | EN 55014-1: 2006 +A1: 2009 +A2: 2011 1997 +A1: 2001 +A2: 2008 2006 +A1: 2009 +A2: 2009 2013 Results | Complies with the requirements of the above specification Authorized by | Robert Song Issue Date | 16 July, 2014 Laboratory | SUZHOU NEW-STANDARD LABORATORY CO LTD NO. 199, JINFENG ROAD, SUZHOU, 215011 P. R. CHINA small [email protected] _HTTP://WWW.NSLAB.CH All applicable tests according to the above specified standard, See clauses tested of the test report. Test results are valid only for the tested samples. This report shall not be reproduced, except in full, without the written approval of the NEW-STANDARD laboratory. Form No. RF-S5014-8Pape ores [Mo] Report No.: NSL-160714010204-R NEW STANDARD LIST OF CONTENTS NO. ‘CONTENTS: PAGES (PAGE NO.) 1 ‘COVER PAGE 10) 2 LUST OF CONTENTS 1@) 3 (GENERAL INFORMATION 365) a ‘SUMMARY OF TESTING 106) 5 EMISSION TEST = oa ‘MAINS TERMINALS DISTURBANCE VOLTAGE 3(79) 2 DISTURBANCE POWER 2 (10-11) 3 DISCONTINUOUS DISTURBANCE 2 (1243) 5a RADIATED EMISSION 2 (14:15) 55 HARMONIC CURRENT 4 (16.19) 36 VOLTAGE FLUCTUATION AND FLICKER 2 (20-21) 6 IMMUNITY TEST = et ELECTROSTATIC DISCHARGE 3 (22-28) 62 RADIO-FREQUENCY ELECTROMAGNETIC FIELD 32527) 63 ELECTRICAL FAST TRANSIENT 2 (28.29) aa SURGE 20.41) 65 INJECTED CURRENT 2 (62-33) os ‘VOLTAGE DIPS AND SHORT INTERRUPTION 2 (3435) 7 "ANNEX = 74 ‘ANNEX 2 (TEST EQUIPMENT LIST) 1(86) 72 "ANNEX 2 (LIST OF CRITICAL COMPONENTS) 1687) 73 [ANNEX 3 (PHOTOGRAPHS OF THE TEST SETUP) 3 (38-40) 74 "ANNEX 4 (PHOTOGRAPHS OF EUT) 3 (a1-43) 73 "ANNEX 5 (TECHNICAL DOCUMENTS) 2 (44-45) Form No.: RF-SS014-A,Report No.: NSL-160714010204-R NEW STANDARD TEST REPORT Electromagnetic compatibility requirements for household appliances, electric tools and similar apparatus- jon and immunity Report: Report No. NSL-160714010204-R. Tested by { (Printed name and signature) Jack Liu ‘Approved by (Printed name and signature) Robert Song Date of issue. 16 July, 2014 Total number of pages 45 Client: Applicant name. Wai Sans Electronic Co, Utd Address Industrial WuYt, DongGang Town, Wuxi Cy, Jiangsu Province, China ‘Manufacturer name ‘Same as applicant ‘Same as applicant Testing Laboratory: SUZHOU NEW.STANDARD LABORATORY CO LTD nn NO. 199, JINFENG ROAD, SUZHOU, 235011 P. R. CHINA Testing location. (NO. 1168, WUZHONG ROAD, SUZHOU, CHINA Test specification: EN 61000-3-2: 2006 +A1: 2009 +A2: 2009 EN 610003-3:2013 Lion Battery Charger ssiciosvss Input: 100-240 ~, 47-63 Hz, 2.0 A MAX ‘Output: 54.6 VDC, 2.08Report No.: NSL-160714010204-R NEWeSTANDARD Copy of marking plate Reese cede Li-ion Battery Charger Pies Ra LN) UEC era aN PO a ery Form No. RF-S3014-AReport No.: NSL-160714010204-R NEWeSTANDARD Test item particulars: Class ‘AC 230 V, 50 Hz ‘On mode Possible test case verdicts: + test case does not apply to the test object... «test object does meet the requirement. - test object does not meet the requirement smn 'N (Not applicable) P (Pass) F (Fail) Testing: Date of receipt of testitem.. Date(s) of performance of tests : OL July, 2014 01 July, 2014 to 16 July, 2014 Environmental condition: Ambient temperature (°C)... Relative humidity (9) wns Atmospheric pressure (kPa).. 22.25 35-45, + 102.2-102.9 General remarks: “EUT" refer to equipment (sample) under test. “CDN” refer to coupling and decoupling network. “LISN” refer to line impedance stabilization network. ‘Throughout this report a poi ‘used as the decimal separator. When determining of test conclusion, measurement uncertainty of test has been considered. The measurement Uncertainty represents an expanded uncertainty expratsed at approximately the 95 % confidence level using & coverage factor of k=2. See below details. Conducted Emission uncertainty (9-150 kHz): 3.6 4B Conducted Emission uncertainty (0.15-30 MHz): 3.5 dB Radiated Emission uncertainty (30-1000 MHz): 4.0 dB General product information This Liion Battery Charger is for household and indoor use. It's designed for charging Li-ion rechargeable battery only. Form No. RF-S3014-ASUMMARY OF TESTING NO. ‘TEST(S) STANDARD(S) RESULT 5-1 MAINS TERMINALS DISTURBANCE VOLTAGE Faz zorr Pp a | ane EEO 7 naa ¢ [ans cussneace7 sami | was ca [rere osc ito 0 2] eat recuENcr i CTONAGRET RD " 3 earnTTRARET eee ; ca [nee ea eeoes oe : 63 owecren ene eects a4 P Remarks Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD EMISSION TEST 5-1 MAINS TERMINALS DISTURBANCE VOLTAGE 5-1-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane. The rear of the EUT was 0.4 m from the vertical coupling plane and connected to the main power through a line impedance stabilization network (LISN). This set up provided 5C ohm / 50 yt coupling impedance for the measuring equipment 2. The conducted emissions were measured between the line phase and ground, and between the neutral phase. ‘and ground using an EMI Receiver. 3. The frequency range from 150 kHz to 30 Miz is checked. 5-1-2 TEST SETUP EMI Receiver EUT 1 r USN Za ‘5-1-3 MEASUREMENT LIMITS Frequency (MHz) Limits dB(uV) Quasl-Peak Average” 0.15-0.5, 66-56 53-46 05-5 56 46 5:30 60 50 “Ifthe limit for the measurement with the average detector fs met when using a receiver with a quasi-peak detector, the equipment under test shall be deemed :o meet both limits and the measurement using the receiver ‘with an average detector need not be carried aut. Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD EMISSION TEST 5-1 MAINS TERMINALS DISTURBANCE VOLTAGE 51.4 TEST RESULTS Phase: Line wa aw WN, ; . " Mar VV VITNt ae ‘Freq. Teminal |__Measured(dBuV) (aBuV) ‘Marga(dB) ‘Note 2 SSS Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD EMISSION TEST 5-1 MAINS TERMINALS DISTURBANCE VOLTAGE 51.4 TEST RESULTS Phase: Neutral wa aw i Sep l i VN en ono a ana = ‘wo000 eq | tnd | Moment Tawa) | WongnaB Nae cuss) | UN | @Mode | AVMode | QPMote | AvMed 04s x] sss | 3057 | e600 | soo | 90m Ea on x | 3 | 362 | soe | ses | 930 PEAK 039 w | sa | asao | ator [seas | as PEAK Form No. RF-S3014-AReport No.: NSL-160714010204-R Page 10 of 45 NEW-STANDARD EMISSION TEST 5-2 DISTURBANCE POWER 5-2-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane. The straight portion of ‘main lead would put on 6 m long testing bench, if main lead is shorter than 6 m it should be extended. 2. The absorbing clamp is pasitioned for maximum indication at each test frequency range from 30 MH? to 300 ‘Mi, that means is clamp moved along the main leed until the maximum emission value Is found. 3. The test result of the worst-case con 5-2-2 TEST SETUP jon was recorded. ‘Absorbing Clamp EU. = = Ground Plene ACIN 5-2-3 MEASUREMENT LIMITS Household and similar appliances 1 2 3 Frequency (MHz) dB (pW) dB (pw) Quasi-peak Average” 30-300 4555, 35-45, ° ifthe limit for the measurement with the average de:ector Is met when using a recelver with a quast-peak detector, the equipment under test shall be deemed to meet both limits and the measurement using the receiver with an average detector need not be carried out. Form No. RF-S3014-Apage oF 5 feport No: NSL-A6O734O1O2OH-A Sas EMISSION TEST 5-2 DISTURBANCE POWER: 5-2-4 TEST RESULTS isis ou isa oRaet “ ra cacao r atl J ane is a ie i ig ——sat0 Fears) Faas ass] rere Wage nano [mo ae | eer [Get | cosh) can ak Tae see [ae aera = sar Bir se seor [sar mie > + Sur | wea asst esto fe +e Ber [ si seat aa me > Hee Be [ aes aes em oP fe jena [ ara [ster es rt mee Form No. RF-S3014-AReport No.: NSL-160714010204-R NEWSTANDARD EMISSION TEST 5-3 DISCONTINUOUS DISTURBANCE 5-8-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane at a semi-anechoic chamber. 2. The EUT to be measured is connected to an artificial mains network for the frequency range 150 kHz to 30 MHz. The test receiver is connected to the artificial mains network and an oscilloscope is connected to the RF output af ‘the test receiver. The cut off frequency of the oscilescope shall be not lower than the IF of the test receiver. 3. Set the program to let the EUT to produce 40 clicks of, where relevant, 40 switching operations. When, 120 min, after the beginning of the test, 40 clicks have not been produced, the testis stopped at the end of the programme in progress, 4. For frequency range 148.5 kHz to 500 kHz, using 150 kHz to determine click rate Nj and frequency range 500 kHz ‘to 30 Miz, using 500 kHz to determine click rate N. 5. The frequency points 150 kHz, 500 kHz, 1.4 MHz, 30 MHz was checked 5-3-2 TEST SETUP. EMI receiver with Time domain/Click meter AMN EUT 5-3-3 MEASUREMENT LIMITS Frequency (MH2) Lents d8(qV) Quast Peak ‘Average® 0.15-05 66-56 39-46 055 36 46 530 30 50 “Ifthe limit for the measurement with the average detector Is met when using a receiver with a quasi-peak detector, the equipment under test shall be deemed :o meet both limits and the measurement using the receiver with an average detector need not be carried out. Form No. RF-S3014-AReport No.: NSL-160714010204-R NEWSTANDARD EMISSION TEST 5-3 DISCONTINUOUS DISTURBANCE 5-8-4 TEST RESULTS Remark: EUT is a household battery charger, the test does not apply. Form No. RF-S3014-AReport No.: NSL-160714010204-R NEWSTANDARD EMISSION TEST 5-4 RADIATED EMISSION 5-4-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane at 2 semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 m away from the interference-recelving antenna, which was mounted on the top of a variable-height antenna tower 3. The antenna is broadband antenna, and its heights varied from 1 to 4 m above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the ‘measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to the heights from 1 to 4 m and the ratable table was turned from 0 degrees to 360 degrees to find the maxirnum reading. 5. The frequency spectrum from 30 MHz to 1000 MHz was scanned and maximum emission levels at each frequency recorded, 5-4-2 TEST SETUP. Equipmant under Test aa Test Distance ost Seong Pte ‘TumTeble Bec 5-4-3 MEASUREMENT LIMITS Frequency (MH2) ‘Quasi-peak limits 45(uV/m)* 30-230 421035" 230-1000 ae Remark * at the transition frequency, the lower limit applies. "is 3 meters measurement limit Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD EMISSION TEST 5-4 RADIATED EMISSION 504.4 TEST RESULTS Remark: EUT is a household battery charger, the test does not apply. Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD EMISSION TEST 5-5 HARMONIC CURRENT 5-5-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane and operated to produce the maximum harmonic components under normal operating conditions for each successive harmonic component in turn 2. The correspondent test program of test instrument fo measure the current harmonics emanated from EUT is chosen, The measure time shall be not less than the necessary for the EUT to be exercised, 5-5-2 TEST SETUP. Power Analyzer Impedance Network AC Power Cord AC Source EUT 5-5-3 MEASUREMENT LIMITS Harmonic order ‘Maximum permissible harmonic current (o) Class & (Ode harmonics 3 2.30 5 14 7 077 9 0.40 fry 0.33 1B oat 1560539 ous * Even harmonics 2 1.08 4 0.43 6 0.30 Bens 023 F Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD EMISSION TEST 5-5 HARMONIC CURRENT 5-5-4 TEST RESULTS TestResult: Pass Source qualification: Normal Current & voltage waveforms 300 is 200 § = 100 B 2 0 8 -100 & e -200 ~ -300 Current RMS(Amps) 4 8 12 16 20 24 28 32 36 40 Harmenic # ‘Testresult: Pass Worst harmonic was #24 with 7.13% of the limit, Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD EMISSION TEST 5-5 HARMONIC CURRENT 5-5-4 TEST RESULTS Test Resull:Pass Source qualification: Normal THC(A): 0.10 LTHD(%): 35.18 POHG{A): 0.008 POHG Limin(ay: 0.251 Highest parameter values during test: ‘V_RIMS (Volts): 220.28, Frequency(Hz): 50.00 [Peak (Amps): 0-603 TLRMS (Amps): 0.325 [Fund (Amps): 0-300 GrestFactor: 1-808 Power (Watts); 64.7 PowerFactor; 0.925 Harm Harms(ava) 100%Limit %of Limit Harms(rmax) 150%Limit Shot Limit Status 2 0001 1.080, oa 0.001 1520-006 Pass 3 9401 2.300, 44 0102 3450 «257 Pass 4 0001 0.430, oa Oot = stS O11 Pass, 5 oom 1.140, 14 0015 1710081 ass 8 1000 0:30, oa 0000 ©0450 0.08 Pass T 0008 0.770 08 0008 = 1.455056 Pass: 8 1000 = 0.230, oa 0000 = «0345 Ok Pass. 9 oc = 0.400, 08 0.003 0.800045 Pass 0 0.000 0.184, oa 0.000 0.276 «Ot Pass u 0004 0330, 14 0004 = od95 8 Pass 2 0000 Oct, 04 0000 «0230042 Pass a oom = 0240, 5A 0011 = 0315348 Pass, 4 ou ont3Y oa Oud ASF OS Pass. 5 door = 0-180, 50 0008 ©0225 340 Pass 6 0000 0.145, oa 0000 ©0473, O43. Pass, w 002 0.132, 14 0003 0199128 Pass a 01000 0-102, 02 0000 ©0453 O47 Pass 2 003 0.148, 23 0004 «0.478208 Pass. 20 0.000 0.092, 02 0000 «O38 0.19 Pass. 2 ooos = o.t07 74 0003 © 04s) 4.82 Pass, 2 0.000 0.084 02 0000 «0.425020 Pass 2 0.002 0.098, 17 0002 «OMT = 121 Pass 2 01000 = o.077 02 000001157 Pass. 25 002 0.090, 22 0002 0435159 Pass 25 0.000 0.071 03 0.000 0.406 «0.23 Pass 27 001 0.083, 17 0002 0425130 Pass, 28 0000 0.086 07 0001 0099S O54 Pass 23 0.003 0.078, 45 0.004 0.116 3.30 Pass, 30 0.000 0.061 oa 0000 0092035 Pass. 3 003 0.073, 44 0003 0409-253 Pass 2 9.000 0.058 98 0.001 0.086.080 Pass. 33 01003 0.088, 44 0003 0.402, 3.08 Pass B 0.000 0.05 oa 0000 =a) 0.33 Pass 35 002 0.064 33 0003 0098 «278 Pass. 35 01000 0.051 03 0000 ©=07F_=— 032 Pass, a” 0.008 0.061 Ta 0005 0091505 Pass 38 0.000 0.048, oa 0000 0.073.036 Pass 39 0001 0.058, 13 0001 0.087 ~= 1:09 —Pass a 01000 0.046, 08 0000 = 0089) 0a7 Pass Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD EMISSION TEST 5-5 HARMONIC CURRENT 5-5-4 TEST RESULTS TestResult:Pass Source qualification: Normal Highest parameter values during test: Voltage (Vrms): 220.29 Frequency(Hz): 50.00 Peak (Amps): 0.603 ERIS (Amps): 0:325 [Fund (amps): 0.300, GrestFactor, 1.908, Power Watts): 64.7 Power Factor: 0.925 Harm Harmonics Vams Limit Vams eof Limit status, 2 0.063, oat 14.19 OK 3 0.480 s82 2422 OK 4 0.098 oso 237 OK 5 0.032 ost 3.58 OK 6 0.065, oat 1474 ok 7 0.063, 0861 959 OK 8 0.028, oat OK 8 0.064 0.440 ok 10 0018 oso ok " 0.028, 0220 OK 2 oor 0220 OK 8 O24 0220, OK 4 0.007 0220 OK 8 0014 0220, ok ” 6.005, 0220, OK 8 dott 0220, ok 1 0.009 0220 OK 2» oor 0220 OK a 0.012 0220 Ok 2 0.004 0220, OK B 0.905 0220 OK & 0.004 0220 OK B 0.005, 0220, OK 2 0.004 0220 OK a 0.005 0220, ok 2 008 0220 OK 2 8.008 0230 OK 0 0,003, 0220 OK 3 0.008 0220, ok 2 0.003 0220 OK 8 5.007 0220, ok aM 0.003, 0220 OK 3 0.005 0220 ok 8 0.003, 0220, OK a Boo o220 OK 3 0.003 0230 ok 30 0.008 0220, OK 0 0.009 0220 OK Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD EMISSION TEST 5-6 VOLTAGE FLUCTUATION AND FLICKER 5-6-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane. The EUT was set in series with the power analyzer through an impedance network for the measurement of flicker voltage, 2. The supply voltage and frequency setting on the programmable AC source was programmed as the rated voltage and frequency of the EUT. 3. During the flick measurement, the measure time shall include that part of whole operation changes. The ‘observation period for short-term flicker indicator Is 10 minutes and the abservation period far long-term flicker indicator is 2 hours. 5-6-2 TEST SETUP Power Analyzer Impedance Network AC PowerCord ‘AC Source eur 5-6-5 MEASUREMENT LIMITS Testitem Lint Relative voltage change characteristic dt (%) 33 ‘Maximum relative voltage change dmx) ‘ Relative Voltage change de (56) 33 Short term flicker Pst 1 Long term flicker Plt 0.65 Form No. RF-S3014-APage 21 of 45, Report No.: NSL-160714010204-8 EMISSION TEST 5-6 VOLTAGE FLUCTUATION AND FLICKER 5-6-4 TEST RESULTS Test Result Pass Status: Test Completed sh and limit tine ‘European Limits, 102 E o7s H oso eee BEE EEE 8 B Pitan imine oro é ozs owe HES & 8 Testlimit (3.30 Pass Testlimit(ms: $00.0 Pass Testlimit (se 3.30 Pass Testlimit(s 400 Pass. Test limits 4900 Pase Test limit: 0850 Pass Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD IMMUNITY TEST 6-1 ELECTROSTATIC DISCHARGE 6-1-1 ELECTROSTATIC DISCHARGE ‘TEST PROCEDURE 1. The EUT was placed on a conductive surfaces table which was 0.8 m above the ground plane. 2. During the test, It was performed with single discharges. fr the single discharge time between successive single discharges was at least 1 second. the EUT shall be exposed to at least 200 discharges, 100 each at negative and positive polarity, at a minimum of four test points. one of the test points shall be subjected to at least 50 indirect discharges to the center of the front edge of the horizontal coupling plane. the remaining three test points shall each receive at least 50 direct contact discharges. 3. f no direct contact test points are available, then atleast 200 indirect discharges shall be applied in the indirect made. test shall be performed at a maximum repeti:ian rate of ane discharge per second. 4. Vertical coupling plane (VCP The coupling plane, of dimensions 0.5m x 0.5m, is p'aced parallel to, and positioned at a distance Q.4m from, the EUT, with the discharge electrode touching the coupling plane. the four faces of the EUT will be performed with electrostatic discharge. 5. Horizontal coupling plane (HCP): ‘The coupling plane Is placed under to the EUT. The generator shall be positioned vertically ata distance of 0.1m from the EUT, with the discharge electrode touching the coupling plane. the four faces of the EUT will be performed with electrostatic discharge, 6. Air discharges at insulation surfaces of the EUT. It was atleast ten single discharges with positive and negative at the same selected point, Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD IMMUNITY TEST 6-1 ELECTROSTATIC DISCHARGE 6-1-2 TEST SETUP ‘Typical position for inaivoct Slecharge to VOR Horzontal coupling plane (Hee) 15m «08m Ground reference plane ‘Wooden tabie eon 6-1.3 MEASUREMENT LIMITS (PERFORMANCE CRITERIA) Criterion a: ‘The apparatus shall continue to operate as intended during the test. Criterion B: ‘The apparatus shall continue to operate as intended after the test Criterion ¢c: Temporary loss of function is allowed, provided the function is self recoverable or can be restored by the operation of the controls, or by any operation specified in the instructions for use. Form No. RF-S3014-APage 24 of 45 Report No.: NSL-160714010204-R NEW-STANDARD IMMUNITY TEST 6-1 ELECTROSTATIC DISCHARGE 6-1-4 TEST RESULTS Criterion B. Location Air discharge (kV) Contact discharge (kV) 2 4 8 #19 2 4 26 8 HeP(front) = ~ HeP(rear) = — HeP(left) 7 HeP(right) - vortfront) = vcP(rear) ~ ~ vertleft) = — vver{right) - Plastic enclosure 4 Output terminal b Remark During the test no loss of performance was observed. After the test the EUT functioned as intended. No unacceptable loss of performance was observed Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD IMMUNITY TEST 6-2 RADIO-FREQUENCY ELECTROMAGNETIC FIELD 6-2-1 TEST PROCEDURE 1. The equipment to be tested Is placed in the center cf the enclosure on a non-conductive table which was 0.8 m above the ground plane, The equlprnent is then connected to power and signal leads according to pertinent installation instructions. 2. The antenna which is enabling the complete frequency range of 80-1000 MHz is placed 3m away fram the equipment. The required field strength is determined by placing the field strength meter on top of or directly alongside the equipment under test and monitoring the field strength meter via a remate field strength indicator ‘outside the enclosure while adjusting the continuous-wave to the applicable antennae. 3. The test is normally performed with the generating antenna facing each of four sides of the EUT. The polarization of the field generated by the broadband antenna necessitates testing each position twice, once with the antenna positioned vertically and again with the antenna positioned horizontally, 4, At each of the above conditions, the frequency range is swept 80-1000 MHz, pausing to adjust the R. signal level or to switch oscillators and antenna. The rate of sweep is in the order of 1.5x10° decades/s. The sensitive frequencies or frequencies of dominant interest may be discretely analyzed. 5. The field strength level was 3V/m, 6-2-2 TEST SETUP ‘ 4 : Distanca according to IEC 61900-4.3, ot t mweur | Aandeot Antenna, Pees heogm Insulated h 4 table Fiter 3 Handset and AA ooh © AC maineting D—" enensiontine Eq 2 A AE] Subscriber line Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD IMMUNITY TEST 6-2 RADIO-FREQUENCY ELECTROMAGNETIC FIELD 6-2-3 MEASUREMENT LIMITS (PERFORMANCE CRITERIA) Criterion A: The apparatus shall continue to operate as intended during the test. Criterion B: ‘The apparatus shall continue to operate as intended after the test Criterion C: Temporary loss of function Is allowed, provided the function Is self recoverable or can be restored by the operation of the controls, of by any operation specified in the instructions for use. Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD IMMUNITY TEST 6-2 RADIO-FREQUENCY ELECTROMAGNETIC FIELD 6-2-4 TEST RESULTS Remark: EUTis a household battery charger, the test does not apply. Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD IMMUNITY TEST 6-3 ELECTRICAL FAST TRANSIENT 6-3-1 TEST PROCEDURE 1. The EUT was placed on a non-conductive table which was 0.8 m above the ground plane. This reference ground plane shall project beyond the EUT by at least 0.1m on all sides and the minimum distance between EUT and all other conductive structure, except the ground plane beneath the EUT, shall be more than 0.5m. 2. The EUT is connected to the power mains by using a coupling device which couples the EFT interference signal to AC power lines, Both polarities of the test voltage stould be applied during compliance test and the duration of the test is 2 minutes, 6-3-2 TEST SETUP Couping!secauping sections Linostexminats shal be mounted dracty on tobo tosiod the reference grourd plane. Capacitor \ crite SS or 28 short as oossible \ ~ \ wN Lines Docoupting Coupling network device Incutotng ‘support Ground reference plane \ Grounding connection according to the manufacturer's specticaten, Largin to be specinec imme test pian Elactical fast °N this tenath should be< tm Grouna reterence plane 6-3-3 MEASUREMENT LIMITS (PERFORMANCE CRITERIA) Criterion a: ‘The apparatus shall continue to operate as intended during the test. Criterion B: ‘The apparatus shall continue to operate as intended after the test. Criterion Cc: ‘Temporary loss of function is allowed, provided the function is self recoverable or can be restored by the operation of the controls, or by any operation specified in the instructions for use. Form No. RF-S3014-AReport No.: NSL-160714010204-R Page 29 of 45 NEW-STANDARD IMMUNITY TEST 6-3 ELECTRICAL FAST TRANSIENT 6-3-4 TEST RESULTS Criterion B. Location Test level Rise time/hold time | Repetition frequency Pre kV) (0s) (kti2) Line 4 550 5 P Neutral 4 550 5 P Line + Neutral 41 550 5 P PE al 560) 5 p Line + PE 41 5360) 5 e Neutral + PE 41 980) 5 e Line + Neutral + PE al 550 5 P Signal Line a = N DCLine fe és - N Remark During the test no loss of performance was observed. After the test the EUT functioned as intended. No lunacceptable loss of performance was observed Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD IMMUNITY TEST 6-4 SURGE 6-4-1 TEST PROCEDURE 1. The EUTand the auxilary equipment were placed 01 a table of 0.8m above the metal ground plane. The size of ground plane is greater than 11 m and project beyond the EUT by at least 0.1.m on all sides. The ground plane is connected to the protective earth. The length of power cord between the coupling device and the EUT was less than 2 m (provided by the manufacturer), 2. The EUT was connected to the power mains throught a coupling device that directly couples the surge interference signal. The surge noise was applied synchronized to the voltage phase at the zero crossing and the Peak value ofthe AC voltage wave (postive and negstive) 3. The surges were applied line to line and line(s) to earth. When testing line to earth the test voltage was apt successively between each ofthe lines and earth. Steps up to the test level specfied increased the test voltage. Alllower levels including the selected test level were tested. The polarity of each surge level included posite and negative test pulse (6-4-2 TEST SETUP. ToAC Surge Immunity EUT Source Test & q ‘Support Units Controller Computer 6-4-3 MEASUREMENT LIMITS (PERFORMANCE CRITERIA) Criterion A: The apparatus shall continue to operate as intended during the test. Criterion B: ‘The apparatus shall continue to operate as intended after the test Criterion C: ‘Temporary loss of function is allowed, provided the function is self recoverable or can be restored by the operation of the controls, or by any operation specified in the instructions for use. Form No. RF-S3014-AReport No.: NSL-160714010204-R NEW-STANDARD IMMUNITY TEST 6-4 SURGE 64.4 TEST RESULTS Criterion B. Location Test level Wave-shape data Pre (ev) (us) Line - Neutral 1 1.250 P Line - PE 2 1.260 P Neutral - PE 2 1.260 P Remark During the test no loss of performance was observed. Miter the test the EUT functioned as intended. No unacceptable loss of performance was observed Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD IMMUNITY TEST 6-5 INJECTED CURRENT 6-5-1 TEST PROCEDURE 1. The EUT was placed on an insulating support of 0.1m height above a ground plane. All cables exiting the EUT was supported at a height of 30 mm above the ground reference plane. 2. The EUT was connected to the power mains through a coupling and decoupling networks (CDN). 3, The CDN was located 0.3 m from the EUT as indicated In the diagram above. 4 The test was performed with the test generator connected to each of the CDN in turn while the other non-excited RF input ports of the coupling devices were terminated by a 500 terminator. 5. The frequency range Is swept from 150 kHz to 80 MHz using 3 V signal level, and with the disturbance signal 80% amplitude modulated with 3 1 kHz sine wave. The rete of sweep shall not exceed 1.5 x 107 decades/s. Where the Frequency Is swept incrementally, the step size shall not exceed 19% of the start and thereafter 1% of the preceding frequency value. 6-5-2 TEST SETUP — eaten Amel <0.3m. foe = 2 0.3m where possiola ns | f I | be sua wen coe ‘Breune weerenee plane Cm suppers soem sn>a0on 6-5-3 MEASUREMENT LIMITS (PERFORMANCE CRITERIA) Criterion A: The apparatus shall continue to operate as intended during the test. Criterion B: ‘The apparatus shall continue to operate as intended after the test Clterion c: ‘Temporary loss of function is allowed, provided the function is self recoverable or can be restored by the operation of the controls, or by any operation specified in the instructions for use. Form No. RF-S3014-APage 33 of 45, Report No.: NSL-160714010204-8 IMMUNITY TEST 6-5 INJECTED CURRENT 6-5-4 TEST RESULTS Criterion A Location Frequency range (MHz) ‘Test level (Vems) Pie ‘AC input port 0.15 - 80 3 p Remark During the test na loss of performance was observed. After the test the EUT functioned tunacceptable loss of performance was observed as intended. No Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD IMMUNITY TEST 6-6 VOLTAGE DIPS AND SHORT INTERRUPTION 6-6-1 TEST PROCEDURE 1. The power cord was used as supplied by the manufecturer. The EUT was connected to the line output of the voltage dips and Interruption generator. 2. The EUT was tested for 30% voltage dip of supplied voltage with duration of 200 ms, 100% voltage dip of supplied voltage and duration 10 ms. Both of the dip tests were carried out for e sequence of three voltage dips with Intervals of 10 seconds. 3. Voltage reductions occur at 0 degree crossover point of the voltage waveform. The performance of the EUT was checked after the voltage dip or interruption. 6-6-2 TEST SETUP TOA Source Dips/Interruption Ear ‘and Variations & Simulator Support Units c 1 | ( 7 0. r Contralier Computer 6-6-3 MEASUREMENT LIMITS (PERFORMANCE CRITERIA) Criterion A: The apparatus shall continue to operate as intended during the test. Criterion The apparatus shall continue to operate as Intended after the test. Criterion C: ‘Temporary loss of function is allowed, provided the function is self recoverable or can be restored by the operation of the controls, or by any operation specified in the instructions for use. Form No. RF-S3014-AReport No.: NSL-160714010204-8 New STANDARD IMMUNITY TEST 6-6 VOLTAGE DIPS AND SHORT INTERRUPTION 6-6-4 TEST RESULTS Criterion C Test level (%)UT Frequency (Hz) | Reduction (%)UT_|_Number of periods Pie 0 a7 100) 05, e 63 100) as P 40 47 60 10 P 63 60 12 p 70 a 30 25 e 63 30 30 e Remark During the test no loss of performance was observed. After the test the EUT functioned as intended. No tunacceptable loss of performance was observed. Form No. RF-S3014-AANNEX 1 TEST EQUIPMENT LIST eames = a Voltage Probe Schwarzbeck Tk9146 2014-06-01 Horn Antenna ROHDE & SCHWARZ HFSO6 2014-05-28 Signal Generator ROHDE & SCHWARZ SMLO2 2014-05-28 CDN EM Test MYM3_ 2014-06-01 EM Injection Clamp FCC F.2031 2014-06-01 Absorbing Clamp ROHDE & SCHWARZ MDS21_ 2014-06-01 Form No. RF-S3014-APage 37 of 45 Report No.: NSL-160714010204-R NEW-STANDARD ANNEX 2 LIST OF CRITICAL COMPONENTS Object/part No. | Manufacturer/ trademark | Type/modells) Remarkis) Xcapacitor(O) | Various Various bs X-capacitar(O@) _ | Various Various capacitor (C¥1, | Various Various Max. 4700 pF E cv) ‘capacitor (C¥3, | Various Various Max. 2200 pF 7 cra) Transformer (T1) | Wuxi Zhongtong Electronics | ssB10ovss-eR35- | — - Co, Lid ce Line chock (FL1) | Wuxi Zhongtong Electronics | Ssi-03 = E Co, Lid Line chock (FL2) | Wuxi Zhongtong Electronics | ssi-o1 = = Co, Ltd Form No. RF-S3014-Amena Mn) Report No.: NSL-160714010204-8 NEW.STANDARD ANNEX 3 PHOTOGRAPHS OF THE TEST SETUP. oO o # 7 g & z = o z g 2 No.2 1 test io. 5-1 BE Test 0.5.2 CO testo. 5:3 1 test W0.5-4 Di testo 55 CO Test No. 5-6 C1 Test No. 6-1 1 testo. 62 D1 Test No. 6-3 Lest Wo. 6-4 C1 testo. 65 D1 Test No. 6-6 D1 other: Form No. RF-SS014-AReport No. Page 39 of 45, NSL-160714010200-R ANNEX 3 PHOTOGRAPHS OF THE TEST SETUP. No.3 1 test Wo. DD testno, 1 test Wo 1 test no. Ll Test No. Be Test No. 1 testo D1 test Wo. testo 1 testno. DO testno, No. a D1 testo. D testo. L test Wo L test no. 1 testo. 1 test Wo. Bi test Wo. 1 test No. D1 testno, 1 Test Wo LO testo. OD reso. D other: Form No. RF-SS014-Aagi ma) Report No.: NSL-160714010204-8 NEW.STANDARD ANNEX 3 PHOTOGRAPHS OF THE TEST SETUP. No.5 C1 testo. 51 Di testos-2 0 | D1 test v0.53 Dtesttios4 | Di testos-5 i CO testo. 5.6 Crest et CO testo. 62 Dd test io. 63 testes Di testNo 6-5 aaa ly No.6 1 est ho. 5-1 C1 test 0.5.2 CO testo. 5:3 1 test W0.5-4 CO testo. 55 CO test io. 5-6 CO test io. 61 1 testo. 62 D1 Test No. 6-3 Lest Wo. 6-4 DE test 0.65 D1 Test No. 6-6 D1 other: Form No. RF-SS014-AReport No.: NSL-160714010204-8 New STANDARD ANNEX 4 PHOTOGRAPHS OF EUT No.2 Bl General 1 Appearance CO tobet 1 internat C1 Pee board | 1 Trensformer CO Mctor 1 other: No.2 1 General Bi] appearance CO tebet O internat 1 Pct boar 1 Transformer O Motor Ol other: Form No. RF-SS014-AReport No.: NSL-160714010204-8 Page 42 of 45, ANNEX 4 PHOTOGRAPHS OF EUT No.3 1 General [al Appearance D babel D1 internat 1 pce board DD Transformer 1 Motor 1 other: No.4 OO Generai 1 Appearance DO tobet B internal 1 pce board Transformer OO motor D other: Form No. RF-SS014-Aag ma) Report No.: NSL-160714010204-8 NEW.STANDARD ANNEX 4 PHOTOGRAPHS OF EUT No.5 LD General D1 Appearance Di tavet OO imernat ! Bl pce board i 1 Transformer O motor t Di other: ' No.6 OO General 1 Appearance DO tater 1 internat Bd ce board 1 Transformer OO Metor D0 other: Form No. RF-SS014-APage 44 of 45, Report No.: NSL-160714010204-8 New STANDARD ANNEX 5 ‘TECHNICAL DOCUMENTS Schematic diagram ee WBF] bed Form No. RF-S3014-APage 45 of 45 Report No.: NSL-160714010204-8 ‘TECHNICAL DOCUMENTS Layout diagram Form No. RF-SS014-A