1 2 3 4

Case Study: Caries Access (1) Pre-op – Subgingival decay maxillary left central and lateral. (2) Collar tissue sculpted to expose decay using the fine tipped Scalpel Point electrode.
(3) Decay removed, and teeth prepped. No additional retraction cords or pastes were used to maintain the dry field. (4) 1 week post -op.
Efficient, Precise Tissue Management
Simplifying and improving the treatment outcomes of the procedures performed every day in your
dental office, the Sensimatic 700SE cuts faster than a diode laser and produces less bleeding and better
visibility1 of the treatment site than a scalpel.

W
hile devices with frequencies above 100 kHz (.1 MHz) can With a combined 30 customizable settings, (3 for Modes: CUT,
be used for electrosurgical procedures, the Sensimatic® CUT/COAG and COAG and 10 for Power), and 7 unique electrodes,
700SE uses a high radiofrequency (1.4 – 1.7 MHz) to cut and you will be able to treat virtually any clinical situation that comes
coagulate soft tissue. When used with the appropriate electrode, the your way.
advantage of operating at this high frequency is reduced collateral
tissue trauma and damage during cutting.

In addition to operating at a high radiofrequency, the Sensimatic

What is Monopolar?
700SE’s low-impedance circuitry continually measures the imped- Because of its versatility and clinical effectiveness, monopolar is
ance in the tissue at the active electrode (where the tissue contacts the most commonly used electrosurgical modality used through-
the cutting electrode) and adjusts the power as needed to enable out healthcare.
stable, consistent passage of the electrode through the soft tissue
as cutting depth varies. The monopolar Sensimatic generates 3 different high frequency
waveforms. Each has differing surgical characteristics, which
cause different histological effects on soft tissue.

• RF Mode No. 1 – “CUT MODE” (cutting with least coagu-

lation): A filtered, unmodulated current for cutting with
the least amount of coagulation. Suited for closed wound
surgery where incisions will be sutured.

• RF Mode No. 2 – “CUT/COAG MODE” (cutting with

balanced coagulation): A fully rectified, modulated,
undamped current for cutting with coagulation when
control of bleeding is desired. It is the most widely
employed current in dentistry and is suited for cutting
procedures where incisions will not be sutured.

• RF Mode No. 3 – “COAG MODE” (full coagulation without

cutting): A partially-rectified current for coagulation with-
out cutting. This waveform has been found most effective
for precise pin-point surface coagulation with minimal
tissue destruction.

1. Scalpel versus electrosurgery: Comparison of gingival perfusion status using ultrasound

Doppler flowmetry. N. Manivannan, R. S. Ahathya,1 and P. C. Rajaram2
Why Use the Sensimatic 700SE?
Dentists are not the only healthcare providers who routinely
perform surgical procedures using electrosurgery. Medical special-
ists in the fields of Obstetrics and Gynecology, Otorhinolaryn-
gology, Dermatology and Veterinary medicine, to name a few, all
routinely reach for the electrosurgical handpiece each day.

When it comes to dentistry, the following procedures are routinely

performed with the Sensimatic 700SE every day.

• Access to subgingival caries

• Removal of inflamed marginal tissue prior to
crown cementation
• Bleeding control and coagulation
• Troughing for crown impressions
• Pericoronal flap excision
• Edentulous ridge recontouring and tissue trimming
A B C D E F G
• Sculpting tissue for acceptance of an ovait pontic.
• Excision of hyperplastic and hypertrophic tissue
• Gingivectomy/gingivoplasty
Seven Unique Electrodes to Treat Virtually
• Frenectomy Any Clinical Situation (see back):
• Esthetic tissue recontouring A. AP1.5-Troughing Point F. C3-Hemostasis Ball
• Exposing teeth for orthodontic eruption B. T16-Horizontal Loop G. P4-Proximal Hemostasis Tip
• Periodontal flap surgery C. T5-Large Tissue Shaving Loop (Sold separately)
• Controlling localized bleeding D. T8-Vertical Loop
• Tissue biopsy E. T2-Scalpel Point
• Crown lengthening

Advantages of Electrosurgery Over a

Diode Laser
• Thin wire electrodes can be adjusted to meet clinical
contour needs
• The side of the electrode wire can cut in addition to the tip
(Only the tip is an active cutting surface for a diode laser)
• Procedures are completed in a fraction of the time it takes
to perform the same procedure with a diode laser. 1 2

• A wider, more versatile range of cutting tips

• Lower initial device cost

3 4

3 ¼” H

9 ¼” W 7 ¾” D 5 6

Specifications
Case Study
• Power Requirements:
Line Voltage: 120 Volts +⁄- 10% AC, 60 Hz, 2 amps maximum 1. Pre-op
2. After debridement of calculus deposits
• Operating Frequency: 1.4 -1.7 MHz (megahertz)
3. Electrosurgical tissue removal and sculpting
• Maximum Power Output: 50 Watts rms (@ 500 Ohm load) approx. 4. Surgical procedure completed
• Size: 3 ¼” H x 7 ¾” D x 9 ¼” W (83mm x 191mm x 235mm) 5. Suturing
6. 1 week post-op
• Weight: 6.1 lbs (2.8 kg)
Recommended Electrodes
for Specific Applications
Troughing Proximal
Scalpel Large Vertical Horizontal Hemostasis
Procedure Point (T2) Loop (T5) Loop (T8) Loop (T16) Ball (C3)
Point Hemostasis
(AP1.5) (P4)

Access to Subgingival Caries   

Removal of Inflamed marginal tissue


prior to Crown Cementation

Bleeding Control and Coagulation  

Troughing for Crown Impressions   

Crown Lengthening   

Esthetic Tissue Contouring   

Edentulous ridge Recontouring and Tissue Trimming   

Sculpting tissue for acceptance of an ovait pontic.    

Excision of Hyperplastic and Hypertrophic Tissue     

Pericoronal Flap Excision   

Gingivectomy/Gingivplasty    

Frenectomy 

Exposing teeth for orthodontic eruption    

Periodontal Flap Surgery 

Controlling localized Bleeding 

Tissue Biopsy  

Available Products
SKU # PRODUCT DESCRIPTION

Sensimatic® 700SE Electrosurge

D700SE-110 (1) Electrosurge unit, (6) electrodes, (1) foot switch,
(1) handpiece and cable, (1) indifferent plate and cable.

S397-T02 Scalpel Point—T2 Electrode

S397-T05 Large Loop—T5 Electrode

S397-T08 Vertical Loop—T8 Electrode

S397-T16 Horizontal Loop—T16 Electrode

S397-C03 Hemostasis Ball—C3 Electrode

S397-AP1.5 Troughing Point—AP1.5 Electrode

S397-P04 Proximal Hemostasis Electrode—P4 (Not included with unit).

D634 Indifferent Plate

Indifferent Plate & Red Cable (NOTE: Connects to newer units

D703
with serial numbers beginning with 90000)

Black Handpiece/Cable (NOTE: Connects to newer units For more information visit Parkell.com
D702
with serial numbers beginning with 90000)

Indifferent Plate & Red Cable (NOTE: Connects to older units

D601
with serial numbers below 90000)

Black Handpiece/Cable (NOTE: Connects to older units

D633
with serial numbers below 90000)

NOTE: When ordering accessories, refer to the serial number located on the bottom of your Parkell, Inc., 300 Executive Dr., Edgewood, NY 11717 USA
Sensimatic 700SE unit to ensure you purchase the correct ones for your model. (800) 243-7448 • Parkell.com