HRO HRS High Pressure Radial Pressure Blowers Catalog 1300

Download as pdf or txt
Download as pdf or txt
You are on page 1of 40

INDUSTRIAL PROCESS AND

COMMERCIAL VENTILATION SYSTEMS

Twin City Fan

HIGH PRESSURE RADIAL


PRESSURE
Twin CityBLOWERS
Fan
MODEL HRO | MODEL HRS

CATALOG 1300 | MAY 2012 WWW.TCF.COM


HIGH PRESSURE BLOWERS

OVERVIEW
HRO I HRS
Model HRO and HRS fans from Twin City Fan & Blower
are specifically designed to provide low flow and high
static pressure for industrial applications. The wheel
design offers maximum strength and reliability.

Available in three (3) designs, the HRO and HRS allow for
flexibility in selection depending upon the application. The
design allows for a low flow reducing or even eliminating
the requirement for recirculating or exhausting excess air.
Design 1 has the lowest flow, followed by Design 2, and
then Design 3.

Typical Applications
• Air pollution control systems
• Combustion air
• Exhausting
• Gas boosting
• Glass blowing and cooling
• Liquid agitation
• Mist elimination
• Pneumatic conveying
• Pressure and vacuum drying
• Primary air supply to ejectors
• Product cooling
• Selective catalytic recovery
• Sulfur recovery
• Vapor recovery
• Water blow-off

Design Features
Arrangement 4 • Designed for continuous duty in high pressure, low flow
applications
• Uniform pressures throughout the operating range

Model HRO
• Wheel: radial bladed with backplate and no front shroud
• Two (2) designs (Design 1 and 3)
• Capable of handling low particulate or vapor
• Volumes to 8,500 CFM
• Pressures to 103" w.g.

Model HRS
Twin City Fan • Wheel: radial bladed with backplate and shroud
• Three (3) designs (Design 1, 2 and 3)
• Capable of handling low particulate or vapor
• Volumes to 10,000 CFM
• Pressures to 120" w.g.

Twin City Fan


2 TWIN CITY FAN - CATALOG 1300
DRIVE ARRANGEMENTS

Arrangement 4
Arrangement 4 is a direct drive fan with the wheel mount-
ed directly on the motor shaft. This drive arrangement is
the most compact and requires minimum maintenance
and service. Standard Arrangement 4 fans are suitable to
200°F operating temperature. Maximum rotational speeds
for arrangement 4 fans can be found on page 6.

Arrangement 8
Arrangement 8 is a direct-drive unit with the wheel mount-
ed on a separate fan shaft that is mounted to the fan
pedestal with pillow block bearings (minimum L-10 40,000
hours). The fan shaft is connected to the motor shaft with
a flexible coupling. Arrangement 8 blowers offer the abil-
ity to remove the motor for service without disturbing the
fan assembly. Arrangement 8 units are limited to 300°F as
standard. High temperature packages are available for up
to 600°F. Maximum rotational speeds for arrangement 8
fans can be found on page 6.

Arrangement 1
V-belt drive fans are available in arrangement 1 only.
Arrangement 1 units are limited to 300°F as standard. Arrangement 1
High temperature packages are available for up to 600°F.
Maximum rotational speeds for arrangement 1 fans can be
found on page 6.

WHEEL DESIGN
Wheel Construction
All wheels are constructed to insure maximum strength
and reliability. Wheels are statically and dynamically bal-
anced on the most modern electronic equipment. Every
blower unit is given a final running mechanical test and
trim balance before shipment.

HRO (Radial, Open Wheel)


The HRO wheel features a full back plate with radial
blades that are constructed of steel. The HRO is ideal for
light particulate- or vapor-laden gas streams. The HRO is
only available in Designs 1 and 3.

HRS (Radial, Shrouded Wheel) HRO Wheel


The HRS wheel features a full backplate and a fully
shrouded frontplate. The HRS design develops the most
pressure for a given speed and offers the highest effi-
ciency. The HRS is available in Designs 1, 2, and 3.

HRS Wheel

WWW.TCF.COM 3
CONSTRUCTION FEATURES

Shaft Seal
Standard shaft seals are mounted on the drive side of the
blower housing. They consist of a ceramic felt element in
compression to minimize air leakage. This shaft seal does
not make the fan gas tight. Consult factory for other avail-
able shaft seal options.

Flanged Inlet
Flanged Inlet Flanged Outlet The standard flanged inlet enables attachment of rigid pipe
connections on the blower inlet. The flange is drilled to
match 125/150# ANSI pipe flange.

Flanged Outlet
The standard flanged outlet enables attachment of rigid
pipe connections on the blower outlet. The flange is drilled
to match 125/150# ANSI pipe flange.

Housing Drain with Plug


The standard housing drain consists of a 3/4" NPT half-
coupling welded to the fan housing in the lowest point
allowing for drainage of condensate from fan housing. A
Shaft Seal Housing Drain with Plug plug is included.

ACCESSORIES
Inlet Bell
Installations with an open inlet, an inlet bell (venturi) is
required to achieve the catalog performance. Inlet screen
is available.

Belt Guard
An OSHA belt guard protects personnel from the moving
drive parts. A quick access guard is available.

Shaft and Bearing Guard


Solid sheet metal guards cover shaft and bearings and
come with extended lube lines to a common point out
Access Port Shaft and Bearing Guard either side of the guard. A guard spanning the shaft
between the bearings is also available to provide easy
access to bearings for lubrication and vibration monitoring.
Outlet Blast Gate Optional painted safety yellow is available.
A manually actuated blast gate for mounting to the fan
outlet flange allows for controlling flow to full shutoff. Split Housing
Available for automatic control. Maximum temperature All sizes are designed to permit wheel removal through
250°F. the fan inlet. Sizes 40 and larger are available with a hori-
zontal, pie-shaped, or 3-way split housing, which allows
Access Port removal of the wheel and shaft without disconnecting
Heavy duty access port provides access for wheel inspec- ductwork.
tion. Depending on the fan size, access port may be NPT
coupling and plug or a panel.

4 TWIN CITY FAN - CATALOG 1300


OPTIONAL CONSTRUCTION

Spark Resistant Construction


Fan applications may involve the handling of fumes or
vapors. Such applications require careful consideration by
the system designer to insure the safe handling of such
gases. Twin City Fan & Blower offers the following classifi-
cations of spark resistant construction per AMCA Standard
99-0401. It is the specifier’s or the user’s responsibility
to specify the type of spark resistant construction with
full recognition of the potential hazards and the degree of
protection required.

Construction
Bearing with Shaft Cooler & Shaft Seal
Type A: All parts of the fan in contact with the airstream
must be made of nonferrous material — usually
an aluminum and limited to 200°F.
Type B: The fan shall have a nonferrous wheel and non-
Table 1: Derating Factors for Safe Wheel Speed
ferrous rub ring about the opening through which
the shaft passes — usually an aluminum wheel Temperature Alloy Stainless
and rub ring and limited to 200°F. (°F) Steel Steel
70 1.00 0.99
Type C: Consult factory. 200 0.99 0.95
250 0.98 0.93
Nominally Leak-Tight Construction 300 0.97 0.91
400 0.95 0.87
When leakage is a concern, nominally leak-tight construc- 500 0.93 0.83
tion should be considered. For fans with positive pressure 600 0.90 0.80
conditions at the inlet, please consult the factory. 700 0.80 0.77
800 0.60 0.75
Nominally leak-tight is available for arrangement 1 and
arrangement 8 fans. Construction modifications may
include, but are not limited to (depending on the applica-
tion) continuously welded inlet and outlet flanges, close-
centered bolts on all flanges, access doors, cover plates,
Buna-N rubber shaft seal as standard (other mechanical
seals available).

High Temperature Package Fan


Standard designs are suitable to 200°F for Arr. 4 and
300°F for Arr. 1 and Arr. 8 fans. Units in Arr. 1 and Arr. 8
fans can be modified to suit applications to 600°F. Apply
to Twin City Fan for applications above 600°F.

301 to 500°F: Package includes shaft cooler with guard,


high temperature grease, and TCF blue
enamel paint.
501 to 600°F: Package includes the 301 to 500°F pack-
age modifications plus the addition of
high-temp aluminum paint.

Special materials of construction are available. Consult fac-


tory for availability and pricing.

WWW.TCF.COM 5
ENGINEERING DATA

Table 2. Wheel Weights, WR2


DESIGN 1 DESIGN 2 DESIGN 3
FAN WHEEL WHEEL WHEEL
WR2 WR2 WR2
SIZE WEIGHT WEIGHT WEIGHT
LB-FT2 LB-FT2 LB-FT2
(LBS) (LBS) (LBS)
25 35 13.6 34 12.4 31 9.6
30 51 27.2 51 25.3 46 19.8
35 89 66.7 87 61.1 79 48.0
40 111 111 110 103 100 81.1
45 180 223 174 202 158 159
50 215 332 209 305 189 240
55 332 626 321 568 291 449
60 403 879 393 806 357 640
65 482 1253 471 1150 428 904
70 548 1664 538 1540 488 1213

Table 3. Maximum RPM, Shaft & Bearings


ARRANGEMENT I ARRANGEMENT 8
FAN
SIZE MAX RPM MAX BHP SHAFT DIA. BEARING TYPE MAX RPM MAX BHP SHAFT DIA. BEARING TYPE
25 3600 10 1-3/16 HDB-C 3600 10 1-3/16 SDB-C
30 3600 25 2-3/16 HDB-C 3600 25 1-3/16 SDB-C
35 2700 50 1-15/16 RB-C & RB-CE 3600 50 1-7/16 SDB-C
40 2500 100 2-7/16 RB-C & RB-CE 3600 100 1-11/16 HDB-C
45 2500 200 2-7/16 RB-C & RB-CE 3600 200 2-3/16 HDB-C
50 1800 40 1-15/16 RB-C & RB-CE 1800 40 1-11/16 HDB
55 1800 60 2-3/16 RB-C & RB-CE 1800 60 1-15/16 HDB
60 1800 100 2-11/16 RB-C & RB-CE 1800 100 2-7/16 HDB
65 1800 150 3-7/16 RB-C & RB-CE 1800 150 2-3/16 RB-C & RB-CE
70 1800 250 3-7/16 RB-C & RB-CE 1800 250 2-11/16 RB-C & RB-CE
Note: The "C" in the bearing type denotes a concentric locking-type bearing.

Table 4. Minimum and Maximum Motor Frame Sizes for Arrangement 4 fans
MINIMUM MAXIMUM
1800 RPM 3600 RPM 1800 RPM 3600 RPM
HOUSING MAXIMUM
(4-POLE MOTOR) (2-POLE MOTOR) (4-POLE MOTOR) (2-POLE MOTOR)
SIZE RPM
FRAME FRAME FRAME FRAME
BHP BHP BHP BHP
SIZE SIZE SIZE SIZE
25 3600 1 143T 3 145T 5 184T 10 215T
30 3600 1-1/2 145T 7-1/2 213T 10 215T 25 284TS
35 3600 3 182T 15 215T 25 284T 50 326TS
40 3600 7-1/2 213T 30 286TS 50 326T 100 405TS
45 3600 15 254T 50 326TS 75 365T 200 405TS
50 1800 20 256T N/A N/A 40 324T N/A N/A
55 1800 40 324T N/A N/A 60 364T N/A N/A
60 1800 60 364T N/A N/A 100 405T N/A N/A
65 1800 100 405T N/A N/A 150 445T N/A N/A
70 1800 125 444T N/A N/A 250 449T N/A N/A

Table 5. Bare Fan Weights


HOUSING ARRANGEMENT 1 ARRANGEMENT 4
DESIGN DESIGN DESIGN DESIGN DESIGN DESIGN
SIZE 1 2 3 1 2 3
25 238 238 233 216 215 209
30 395 393 382 357 353 342
35 404 540 542 553 547 553
40 702 695 684 777 768 754
45 882 939 935 1085 1142 1139
50 1087 1079 1052 1049 1038 970
55 1464 1449 1407 1366 1348 1302
60 1745 1719 1678 1649 1619 1572
65 2064 2038 1971 1941 1880 1453
70 2431 2396 2300 2519 2477 2371

Note: Arrangement 1 weights do not include the weight of drives or motors. Arrangement 4 weights do not include
the weight of the motor.

6 TWIN CITY FAN - CATALOG 1300


FAN SELECTION

The performance curves in this catalog are based on fans handling standard air at a density of 0.075 pounds per
cubic foot. This is equivalent to air at 70°F at sea level (29.92" Hg. barometric pressure). Thus, when specified
performance is at a density other than standard, it must be converted to the equivalent standard conditions before
entering the performance curves. The equivalent standard conditions can be calculated by using the Twin City
Fan & Blower Fan Selector Program.

The fan selection curves on the following pages show performance at nominal diameter as well as 80% and
100% of nominal. Variation in wheel width is not available.

Performance curves utilize a logarithmic scale for the axes.

Typical Selection Curve

Horsepower
Fan Size

345
Performance at
Static Pressure (in.-w.g.)

100% Diameter

75
50 100
40

Performance at
80% Diameter

20% of Peak
Static Efficiency

Flow (CFM)

MODEL NOMENCLATURE
HRS - 3 - 45

Model
HRO = Open Front Wheel
HRS = Shrouded Wheel
Design
Design 1 (HRO & HRS)
Design 2 (HRS Only)
Design 3 (HRO & HRS)
Housing Size
(25, 30, 35, 40, 45, 50, 55, 60, 65, 70)

WWW.TCF.COM 7
8
HRO Design 1 - 3550 RPM
200

100
145
80
140
25 30
40
FAN SELECTION

135 50
15 20
50
25 30
130 7-1/2 10

15
125 5 75

TWIN CITY FAN - CATALOG 1300


3 40
20
7-1/2
1-1/2 2
20
3 10

Static Pressure (in.-w.g.)


10

8
HRO – Design 1, 3550 RPM

2
50 80 100 200 500 800 1,000 2,000

Flow (CFM)
HRO Design 3 - 3550 RPM
100
345
80

340 40
50
30
25 75
335 20 25
50 15 30 100
40
50
330 10
15
7-1/2
20
25
5
325 7-1/2 30
3
10

2
20 1-1/2 3
15

Static Pressure (in.-w.g.)


5
HRO – Design 3, 3550 RPM

10

WWW.TCF.COM
5
80 100 200 500 800 1,000 2,000 5,000

Flow (CFM)
FAN SELECTION

9
10
HRS Design 1 - 3550 RPM
200

145
100
FAN SELECTION

140 50
80 30 40
25
75
135 30
20 25
15

TWIN CITY FAN - CATALOG 1300


40
50 15
130 10
7-1/2 20

5 7-1/2
125

Static Pressure (in.-w.g.)


10

2 3
1-1/2
HRS – Design 1, 3550 RPM

20

10
100 200 500 800 1,000 2,000

Flow (CFM)
HRS Design 2 - 3550 RPM
200

245
100

240 75
80 40 50
100
235 40
25 30 50
20

50 20
230 15 25
10
30

10
225 5 7-1/2

Static Pressure (in.-w.g.)


3 5
2
HRS – Design 2, 3550 RPM

20

WWW.TCF.COM
10
200 500 800 1,000 2,000 5,000

Flow (CFM)
FAN SELECTION

11
12
HRS Design 3 - 3550 RPM
200

100 345
FAN SELECTION

80
340
75
50 100
40

335

TWIN CITY FAN - CATALOG 1300


40 50
25 30
50

330 15 20 25
30

Static Pressure (in.-w.g.)


10
325 7-1/2
5
15
HRS – Design 3, 3550 RPM

20 3 5
2

10
500 800 1,000 2,000 5,000

Flow (CFM)
HRO Design 1, Sizes 125-140 - 1780 RPM

20 140

135
2
3
130 1
10 1-1/2
2
8 125 1/2
5
3/4
1/4 1
5

3
1/2

Static Pressure (in.-w.g.)


2

0.8
HRO – Design 1, Sizes 125-140, 1780 RPM

WWW.TCF.COM
0.5
10 20 50 80 100 200 500 800 1,000

Flow (CFM)
FAN SELECTION

13
14
HRO Design 1, Sizes 160-170 - 1780 RPM

170
165
50
160
30
25 40
50
25
20
FAN SELECTION

30

15 40
20
25
50
30

TWIN CITY FAN - CATALOG 1300


75

20

Static Pressure (in.-w.g.)


40

10

8
HRO – Design 1, Sizes 145-155, 1780 RPM

5
200 500 800 1,000 2,000 5,000

Flow (CFM)
HRO - Design 1, Sizes 160-170, 1780 RPM
80

170
165
50
160
30
25 40
50
25
20 30

15 40
20
25
50
30
75
20

Static Pressure (in.-w.g.)


40

10

8
HRO – Design 1, Sizes 160-170, 1780 RPM

WWW.TCF.COM
5
200 500 800 1,000 2,000 5,000
FAN SELECTION

Flow (CFM)

15
16
HRO Design 3, Sizes 325-340 - 1780 RPM

20
340

335 3
2
FAN SELECTION

5
1-1/2
10 330
1 2

8 3 7-1/2
3/4
1/2

TWIN CITY FAN - CATALOG 1300


325
1
1-1/2
1/4
5

1/2

Static Pressure (in.-w.g.)


3/4

2
HRO – Design 3, Sizes 325-340, 1780 RPM

1
50 80 100 200 500 800 1,000 2,000

Flow (CFM)
HRO Design 3, Sizes 345-355 - 1780 RPM

355

350
15

10
345
20 25
7-1/2 10
30
20
5
5 15

3 20
7-1/2
10

Static Pressure (in.-w.g.)


10

8
HRO – Design 3, Sizes 345-355, 1780 RPM

WWW.TCF.COM
5
200 500 800 1,000 2,000 5,000

Flow (CFM)
FAN SELECTION

17
18
HRO Design 3, Sizes 360-370 - 1780 RPM

370
50
365
FAN SELECTION

360 40

30 50
30
25 25
75
20 40
20 50

TWIN CITY FAN - CATALOG 1300


25
15
100
30
40
75

50

Static Pressure (in.-w.g.)


20
HRO – Design 3, Sizes 360-370, 1780 RPM

10
500 800 1,000 2,000 5,000 8,000

Flow (CFM)
HRS Design 1, Sizes 125-140 - 1780 RPM

140
20

135
2 3

5
130 2
1 1-1/2

10

125 1/2 3/4 1


8

1/4

Static Pressure (in.-w.g.)


1/2
5
HRS – Design 1, Sizes 125-140, 1780 RPM

WWW.TCF.COM
2
80 100 200 500 800 1,000

Flow (CFM)
FAN SELECTION

19
20
HRS Design 1, Sizes 145-155 - 1780 RPM
50

155

150
FAN SELECTION

15 20
10
145

10 25

TWIN CITY FAN - CATALOG 1300


7-1/2
5

20 7-1/2 15
5
3

Static Pressure (in.-w.g.)


10
HRS – Design 1, Sizes 145-155, 1780 RPM

10

8
500 800 1,000 2,000

Flow (CFM)
HRS Design 1, Sizes 160-170 - 1780 RPM
80

170

165

50 160 50
30 40
75
40
50
25
20 30

25 30
15 20

40

Static Pressure (in.-w.g.)


20
HRS – Design 1, Sizes 160-170, 1780 RPM

WWW.TCF.COM
10
1,000 2,000 5,000
FAN SELECTION

Flow (CFM)

21
22
HRS Design 2, Sizes 225-240 - 1780 RPM

240
20
FAN SELECTION

235
5
3

230 3
1-1/2

TWIN CITY FAN - CATALOG 1300


2

10

225 3/4 1
1-1/2
8

Static Pressure (in.-w.g.)


1/2
1/4

5 3/4
HRS – Design 2, Sizes 225-240, 1780 RPM

100 200 500 800 1,000 2,000

Flow (CFM)
HRS Design 2, Sizes 245-255 - 1780 RPM
50

255

250

25
15 20
30
245

15
10
7-1/2
20

20 10
7-1/2
5

Static Pressure (in.-w.g.)


HRS – Design 2, Sizes 245-255, 1780 RPM

WWW.TCF.COM
10
800 1,000 2,000
FAN SELECTION

Flow (CFM)

23
24
HRS Design 2, Sizes 260-270 - 1780 RPM
80

270

265

50 75
260
FAN SELECTION

50 100
40
50
30
25 40
75
40

TWIN CITY FAN - CATALOG 1300


20 25 30

50

Static Pressure (in.-w.g.)


20
HRS – Design 2, Sizes 260-270, 1780 RPM

10
1,000 2,000 5,000 8,000

Flow (CFM)
HRS Design 3, Sizes 325-340 - 1780 RPM
20
340

335
5
3
7-1/2

330 3
10 1-1/2 2

325 3/4 1 1-1/2

1/2
5

Static Pressure (in.-w.g.)


1/4
3/4
HRS – Design 3, Sizes 325-340, 1780 RPM

WWW.TCF.COM
2
100 200 500 800 1,000 2,000
FAN SELECTION

Flow (CFM)

25
26
HRS Design 3, Sizes 345-355 - 1780 RPM

355

350
FAN SELECTION

25
30
15
345 20

15 40
10 20

TWIN CITY FAN - CATALOG 1300


20
7-1/2

10 25
5 7-1/2

Static Pressure (in.-w.g.)


15

10
HRS – Design 3, Sizes 345-355, 1780 RPM

8
1,000 2,000 5,000

Flow (CFM)
HRS Design 3, Sizes 360-370 - 1780 RPM

370

50
365

360
75
50 100
40

40 50 75
30

40
25 50
20 30

Static Pressure (in.-w.g.)


20
HRS – Design 3, Sizes 360-370, 1780 RPM

WWW.TCF.COM
10
2,000 5,000 8,000 10,000

Flow (CFM)
FAN SELECTION

27
DIMENSIONAL DATA
Arrangement 1, Design 1
D K J

Ø N, TYP
KK, KEY
LL
H L
E
B
Ø JJ S
A
T
P M
F G CC R
Foundation
THD

D H
H

A A

B
F
F G
D G

UBD BHD

D C

D
H H
H E
FF
E B
E

B A A A
B

C G F C F G
F G

BAU TAD TAU

A B C E
ALL DIS-
FAN
CHARGES D
SIZE BHD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
EXCEPT
BHD1
125 14.06 15.81 12.74 25.82 32.01 15.39 4.06 27.70 17.95 13.63 1.33 17.95 4.06 11.76 13.63 27.07 29.57 34.66 26.45 27.62 26.30
130 16.88 18.13 15.29 30.98 38.42 18.47 4.02 33.23 21.54 16.36 1.59 21.54 4.02 14.11 16.36 32.80 35.48 41.07 31.89 33.36 31.65
135 19.69 21.19 17.83 36.15 44.82 21.54 4.73 38.77 25.13 19.09 1.86 25.13 4.73 16.46 19.08 38.72 40.93 48.00 37.73 39.46 37.46
140 22.50 24.13 20.38 41.31 51.22 24.62 5.31 44.31 28.72 21.81 2.12 28.72 5.31 18.81 21.81 43.31 46.31 54.76 42.32 44.19 42.07
145 25.31 26.56 22.93 46.48 57.62 27.70 5.40 49.85 32.31 24.54 2.39 32.31 5.40 21.16 24.54 49.78 51.69 61.16 48.56 50.09 48.23
150 28.13 29.38 25.48 51.64 64.03 30.78 5.86 55.39 35.90 27.27 2.65 35.90 5.86 23.52 27.26 54.88 57.14 67.91 53.53 55.24 53.16
155 30.94 32.94 28.02 56.80 70.43 33.85 7.07 60.93 39.49 29.99 2.92 39.49 7.07 25.87 29.99 60.21 63.46 74.32 58.66 61.02 58.24
160 33.75 35.25 30.57 61.97 76.83 36.93 7.03 66.47 43.08 32.72 3.18 43.08 7.03 28.22 32.72 64.97 68.84 81.60 63.48 66.29 63.11
165 36.56 37.69 33.12 67.13 83.23 40.01 7.12 72.01 46.67 35.44 3.45 46.67 7.12 30.57 35.44 70.38 74.23 88.01 68.77 71.81 68.37
170 39.38 41.25 35.67 72.30 89.64 43.09 8.33 77.55 50.26 38.17 3.71 50.26 8.33 32.92 38.17 76.23 80.61 94.41 74.24 77.34 73.71

FAN F G
H J K L LL M N P R S T
SIZE TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
125 12.70 12.85 13.01 20.60 12.23 15.51 20.60 13.63 12.39 12.70 12.85 12.55 1.88 4.65 20.86 11.00 – 2.24 0.69 19.54 6.76 4.82 2.41
130 15.24 15.42 15.61 24.19 14.68 17.86 24.19 16.36 14.87 15.24 15.42 15.05 1.56 5.21 23.50 11.19 – 2.07 0.81 21.11 9.27 6.27 3.14
135 17.78 17.99 18.21 28.31 17.13 20.96 28.31 19.08 17.34 17.78 17.99 17.56 1.69 6.13 24.30 12.31 – 2.70 0.81 20.87 9.86 6.86 3.43
140 20.32 20.56 20.81 32.26 19.57 23.81 32.26 21.81 19.82 20.32 20.56 20.07 1.81 6.94 26.68 13.56 – 3.26 0.81 27.20 10.38 7.38 3.69
145 22.86 23.13 23.41 35.85 22.02 26.16 35.85 24.54 22.30 22.86 23.13 22.58 1.81 7.80 29.66 16.69 – 3.86 0.81 21.66 10.89 7.89 3.95
150 25.40 25.70 26.02 39.79 24.47 29.02 39.79 27.26 24.78 25.40 25.70 25.09 2.13 8.68 28.92 16.25 – 4.45 0.81 23.96 11.47 8.47 4.24
155 27.94 28.27 28.62 43.38 26.91 31.37 43.38 29.99 27.25 27.94 28.27 27.60 2.13 9.54 31.20 16.88 – 4.55 1.06 30.69 13.99 9.99 4.99
160 30.48 30.84 31.22 47.85 29.36 34.97 47.85 32.72 29.73 30.48 30.84 30.11 2.38 10.36 33.01 17.62 – 5.11 1.06 41.02 14.50 10.50 5.25
165 33.02 33.41 33.82 51.44 31.80 37.32 51.44 35.44 32.21 33.02 33.41 32.62 2.38 11.22 34.93 18.62 9.31 5.71 1.06 36.32 15.02 11.02 5.51
170 35.56 35.98 36.42 55.03 34.25 39.67 55.03 38.17 34.69 35.56 35.98 35.13 2.38 12.03 37.31 18.81 9.41 5.80 1.06 38.69 17.53 12.47 6.24

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

28 TWIN CITY FAN - CATALOG 1300


DIMENSIONAL DATA
Arrangement 1, Design 2
D K J

Ø N, TYP
KK, KEY
LL
H L
E
B
Ø JJ S
A
T
P M
F G CC R
Foundation
THD

D H
H

A A

B
F
F G
D G

UBD BHD

D C

D
H H
H E
FF
E B
E

B A A A
B

C G F C F G
F G

BAU TAD TAU

A B C E
ALL DIS-
FAN
CHARGES D
SIZE BHD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
EXCEPT
BHD1
225 13.94 16.06 12.54 25.30 31.38 15.28 4.68 27.23 17.47 13.32 1.37 17.47 4.68 11.39 13.32 26.95 29.58 34.38 26.02 27.78 25.79
230 16.69 18.94 15.05 30.35 37.65 18.33 5.27 32.67 20.96 15.98 1.64 20.96 5.27 13.67 15.98 32.95 35.43 41.19 31.62 34.18 31.25
235 19.44 21.19 17.55 35.41 43.93 21.39 5.25 38.12 24.46 18.65 1.92 24.46 5.25 15.94 18.65 38.78 40.84 47.46 37.32 39.40 36.91
240 22.25 24.00 20.06 40.47 50.20 24.44 5.78 43.56 27.95 21.31 2.19 27.95 5.78 18.22 21.31 43.12 46.25 54.09 41.63 43.75 41.26
245 25.00 27.50 22.57 45.53 56.48 27.50 7.00 49.01 31.45 23.98 2.47 31.45 7.00 20.50 23.97 49.74 52.25 61.25 47.93 50.84 47.43
250 27.81 29.81 25.08 50.59 62.75 30.55 7.04 54.45 34.94 26.64 2.74 34.94 7.04 22.78 26.64 54.86 57.34 67.52 52.84 55.31 52.29
255 30.63 33.38 27.58 55.65 69.03 33.61 8.32 59.90 38.43 29.30 3.01 38.43 8.32 25.05 29.30 60.33 63.41 73.80 58.04 61.32 57.41
260 33.38 35.63 30.09 60.71 75.30 36.66 8.30 65.34 41.93 31.97 3.29 41.93 8.30 27.33 31.97 64.68 68.75 80.96 62.45 65.63 61.89
265 36.13 37.88 32.60 65.77 81.58 39.72 8.27 70.79 45.42 34.63 3.56 45.42 8.27 29.61 34.63 70.24 74.09 87.23 67.65 71.10 67.05
270 38.94 41.69 35.11 70.83 87.85 42.77 9.80 76.23 48.92 37.30 3.84 48.92 9.80 31.89 37.29 76.34 80.50 94.57 73.40 76.83 72.60

FAN F G
H J K L LL M N P R S T
SIZE TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
225 12.58 12.81 13.05 20.48 11.88 15.64 20.48 13.32 12.11 12.58 12.81 12.35 1.56 4.80 21.01 11.00 – 2.24 0.69 18.92 7.07 5.13 2.57
230 15.10 15.38 15.66 24.50 14.26 18.67 24.50 15.98 14.53 15.10 15.38 14.81 1.69 5.09 23.99 11.19 – 1.77 0.81 20.48 9.65 6.65 3.32
235 17.62 17.94 18.27 27.99 16.64 20.94 27.99 18.65 16.95 17.62 17.94 17.28 1.69 5.52 25.33 12.31 – 1.88 0.81 20.16 10.30 7.30 3.65
240 20.13 20.50 20.88 31.84 19.01 23.72 31.84 21.31 19.37 20.13 20.50 19.75 1.81 5.81 28.31 13.56 – 1.88 0.81 26.41 10.87 7.87 3.94
245 22.65 23.06 23.49 36.22 21.39 27.25 36.22 23.97 21.79 22.65 23.06 22.22 2.13 6.29 31.79 16.69 – 2.04 0.81 21.04 11.51 8.51 4.26
250 25.17 25.63 26.10 39.71 23.77 29.53 39.71 26.64 24.22 25.17 25.63 24.69 2.13 6.95 31.27 16.25 – 2.41 0.81 23.34 12.09 9.09 4.55
255 27.68 28.19 28.71 43.21 26.14 31.80 43.21 29.30 26.64 27.68 28.19 27.16 2.38 7.62 33.80 16.88 – 2.29 1.06 29.74 14.67 10.67 5.34
260 30.20 30.75 31.32 47.59 28.52 35.33 47.59 31.97 29.06 30.20 30.75 29.63 2.38 8.28 35.84 17.62 – 2.66 1.06 39.86 15.25 11.25 5.62
265 32.71 33.31 33.93 51.08 30.89 37.61 51.08 34.63 31.48 32.71 33.31 32.10 2.38 8.95 38.00 18.62 9.31 3.04 1.06 35.21 15.83 11.83 5.91
270 35.23 35.88 36.54 55.63 33.27 41.39 55.63 37.29 33.90 35.23 35.88 34.57 2.38 9.61 40.61 18.81 9.41 2.94 1.06 37.58 18.40 13.34 6.67

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

WWW.TCF.COM 29
DIMENSIONAL DATA
Arrangement 1, Design 3
D K J

Ø N, TYP
KK, KEY
LL
H L
E
B
Ø JJ S
A
T
P M
F G CC R
Foundation
THD

D H
H

A A

B
F
F G
D G

UBD BHD

D C

D
H H
H E
FF
E B
E

B A A A
B

C G F C F G
F G

BAU TAD TAU

A B C E
ALL DIS-
FAN
CHARGES D
SIZE BHD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
EXCEPT
BHD1
325 13.75 16.38 12.40 24.85 30.80 15.11 5.28 26.76 17.05 13.01 1.36 17.05 5.28 11.10 13.01 26.88 29.85 34.33 25.59 28.37 25.28
330 16.50 18.63 14.87 29.81 36.95 18.13 5.31 32.11 20.45 15.61 1.63 20.45 5.31 13.31 15.61 33.30 35.38 40.49 31.58 34.10 31.11
335 19.25 21.38 17.35 34.78 43.11 21.15 5.84 37.46 23.86 18.21 1.90 23.86 5.84 15.53 18.21 37.68 40.82 47.00 35.82 38.67 35.40
340 22.00 24.75 19.83 39.75 49.27 24.17 7.00 42.81 27.27 20.81 2.17 27.27 7.00 17.75 20.81 43.27 46.50 54.05 40.97 44.25 40.45
345 24.75 27.00 22.31 44.72 55.43 27.19 7.03 48.16 30.68 23.41 2.44 30.68 7.03 19.97 23.41 48.31 51.55 60.20 46.06 49.72 45.51
350 27.50 30.50 24.79 49.69 61.59 30.22 8.31 53.52 34.09 26.02 2.72 34.09 8.31 22.19 26.02 54.96 57.69 67.25 52.31 55.91 51.58
355 30.25 32.75 27.27 54.66 67.75 33.24 8.34 58.87 37.50 28.62 2.99 37.50 8.34 24.41 28.62 60.57 63.29 73.41 57.58 60.76 56.75
360 33.00 36.50 29.75 59.63 73.91 36.26 9.87 64.22 40.91 31.22 3.26 40.91 9.87 26.63 31.22 64.41 69.13 80.63 61.41 66.29 60.68
365 35.75 38.75 32.23 64.60 80.07 39.28 9.90 69.57 44.32 33.82 3.53 44.32 9.90 28.85 33.82 70.64 74.10 86.79 67.08 71.81 66.10
370 38.50 42.00 34.71 69.57 86.23 42.30 10.93 74.92 47.73 36.42 3.80 47.73 10.93 31.07 36.42 76.73 80.39 93.65 72.90 77.34 71.85

FAN F G
H J K L LL M N P R S T
SIZE TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
325 12.46 12.78 13.09 20.58 11.53 16.10 20.58 13.01 11.83 12.46 12.78 12.15 1.56 4.92 21.13 11.00 – 2.24 0.69 17.67 7.30 5.37 2.68
330 14.96 15.33 15.71 23.99 13.84 18.31 23.99 15.61 14.20 14.96 15.33 14.58 1.69 5.23 24.13 11.19 – 1.77 0.81 19.03 9.93 6.93 3.46
335 17.45 17.89 18.32 27.75 16.15 21.03 27.75 18.21 16.57 17.45 17.89 17.01 1.81 5.69 25.50 12.31 – 1.88 0.81 26.88 10.63 7.63 3.81
340 19.94 20.44 20.94 32.05 18.45 24.50 32.05 20.81 18.93 19.94 20.44 19.44 2.13 6.00 28.50 13.56 – 1.88 0.81 24.62 11.25 8.25 4.13
345 22.43 23.00 23.56 35.45 20.76 26.72 35.45 23.41 21.30 22.43 23.00 21.87 2.13 6.44 32.06 16.69 – 1.97 0.81 27.79 11.94 8.94 4.47
350 24.93 25.55 26.18 39.75 23.07 30.19 39.75 26.02 23.67 24.93 25.55 24.30 2.38 6.75 31.94 16.25 – 1.97 0.81 21.97 12.56 9.56 4.78
355 27.42 28.11 28.79 43.16 25.37 32.41 43.16 28.62 26.03 27.42 28.11 26.73 2.38 7.06 34.88 16.88 – 1.47 1.06 27.84 15.19 11.19 5.59
360 29.91 30.66 31.41 47.63 27.68 36.13 47.63 31.22 28.40 29.91 30.66 29.16 2.38 7.48 37.20 17.62 – 1.58 1.06 37.35 15.81 11.81 5.91
365 32.40 33.22 34.03 51.04 29.98 38.35 51.04 33.82 30.76 32.40 33.22 31.59 2.38 8.07 39.50 18.62 9.31 1.85 1.06 32.83 16.44 12.44 6.22
370 34.90 35.77 36.65 55.15 32.29 41.57 55.15 36.42 33.13 34.90 35.77 34.02 2.38 8.67 42.21 18.81 9.41 1.67 1.06 35.04 19.06 14.00 7.00

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

30 TWIN CITY FAN - CATALOG 1300


DIMENSIONAL DATA
Arrangement 4, Design 1
J
D
2X Ø N
WHEN L>18.00
LOCATED AT L/2

H
E T
B
S

A
6X Ø N M
P
F G
Foundation
THD

D H H

A
A
B

F G F
D G
UBD
BHD
C
D

D
H FF H
H
E
E B
E

B A B A A

C F C F G
F G G

BAU TAD TAU

A B C E
ALL DIS-
FAN
CHARGES D
SIZE BHD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
EXCEPT
BHD1
125 14.06 15.81 12.74 25.82 32.01 15.39 4.06 27.70 17.95 13.63 1.33 17.95 4.06 11.76 13.63 27.07 29.57 34.66 26.45 27.62 26.30
130 16.88 18.13 15.29 30.98 38.42 18.47 4.02 33.23 21.54 16.36 1.59 21.54 4.02 14.11 16.36 32.80 35.48 41.07 31.89 33.36 31.65
135 19.69 21.19 17.83 36.15 44.82 21.54 4.73 38.77 25.13 19.09 1.86 25.13 4.73 16.46 19.08 38.72 40.93 48.00 37.73 39.46 37.46
140 22.50 24.13 20.38 41.31 51.22 24.62 5.31 44.31 28.72 21.81 2.12 28.72 5.31 18.81 21.81 43.31 46.31 54.76 42.32 44.19 42.07
145 25.31 26.56 22.93 46.48 57.62 27.70 5.40 49.85 32.31 24.54 2.39 32.31 5.40 21.16 24.54 49.78 51.69 61.16 48.56 50.09 48.23
150 28.13 29.38 25.48 51.64 64.03 30.78 5.86 55.39 35.90 27.27 2.65 35.90 5.86 23.52 27.26 54.88 57.14 67.91 53.53 55.24 53.16
155 30.94 32.94 28.02 56.80 70.43 33.85 7.07 60.93 39.49 29.99 2.92 39.49 7.07 25.87 29.99 60.21 63.46 74.32 58.66 61.02 58.24
160 33.75 35.25 30.57 61.97 76.83 36.93 7.03 66.47 43.08 32.72 3.18 43.08 7.03 28.22 32.72 64.97 68.84 81.60 63.48 66.29 63.11
165 36.56 37.69 33.12 67.13 83.23 40.01 7.12 72.01 46.67 35.44 3.45 46.67 7.12 30.57 35.44 70.38 74.23 88.01 68.77 71.81 68.37
170 39.38 41.25 35.67 72.30 89.64 43.09 8.33 77.55 50.26 38.17 3.71 50.26 8.33 32.92 38.17 76.23 80.61 94.41 74.24 77.34 73.71

FAN F G
H J M N P R S T
SIZE TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
125 12.70 12.85 13.01 20.60 12.23 15.51 20.60 13.63 12.39 12.70 12.85 12.55 1.88 4.65 2.24 0.69 19.54 6.76 4.82 2.41
130 15.24 15.42 15.61 24.19 14.68 17.86 24.19 16.36 14.87 15.24 15.42 15.05 1.56 5.21 2.07 0.81 21.11 9.27 6.27 3.14
135 17.78 17.99 18.21 28.31 17.13 20.96 28.31 19.08 17.34 17.78 17.99 17.56 1.69 6.13 2.70 0.81 20.87 9.86 6.86 3.43
140 20.32 20.56 20.81 32.26 19.57 23.81 32.26 21.81 19.82 20.32 20.56 20.07 1.81 6.94 3.26 0.81 27.20 10.38 7.38 3.69
145 22.86 23.13 23.41 35.85 22.02 26.16 35.85 24.54 22.30 22.86 23.13 22.58 1.81 7.80 3.86 0.81 21.66 10.89 7.89 3.95
150 25.40 25.70 26.02 39.79 24.47 29.02 39.79 27.26 24.78 25.40 25.70 25.09 2.13 8.68 4.45 0.81 23.96 11.47 8.47 4.24
155 27.94 28.27 28.62 43.38 26.91 31.37 43.38 29.99 27.25 27.94 28.27 27.60 2.13 9.54 4.55 1.06 30.69 13.99 9.99 4.99
160 30.48 30.84 31.22 47.85 29.36 34.97 47.85 32.72 29.73 30.48 30.84 30.11 2.38 10.36 5.11 1.06 41.02 14.50 10.50 5.25
165 33.02 33.41 33.82 51.44 31.80 37.32 51.44 35.44 32.21 33.02 33.41 32.62 2.38 11.22 5.71 1.06 36.32 15.02 11.02 5.51
170 35.56 35.98 36.42 55.03 34.25 39.67 55.03 38.17 34.69 35.56 35.98 35.13 2.38 12.03 5.80 1.06 38.69 17.53 12.47 6.24

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

WWW.TCF.COM 31
DIMENSIONAL DATA
Arrangement 4, Design 2
J
D
2X Ø N
WHEN L>18.00
LOCATED AT L/2

H
E T
B
S

A
6X Ø N M
P
F G
Foundation
THD

D H H

A
A
B

F G F
D G
UBD
BHD
C
D

D
H FF H
H
E
E B
E

B A B A A

C F C F G
F G G

BAU TAD TAU

A B C E
ALL DIS-
FAN
CHARGES D
SIZE BHD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
EXCEPT
BHD1
225 13.94 16.06 12.54 25.30 31.38 15.28 4.68 27.23 17.47 13.32 1.37 17.47 4.68 11.39 13.32 26.95 29.58 34.38 26.02 27.78 25.79
230 16.69 18.94 15.05 30.35 37.65 18.33 5.27 32.67 20.96 15.98 1.64 20.96 5.27 13.67 15.98 32.95 35.43 41.19 31.62 34.18 31.25
235 19.44 21.19 17.55 35.41 43.93 21.39 5.25 38.12 24.46 18.65 1.92 24.46 5.25 15.94 18.65 38.78 40.84 47.46 37.32 39.40 36.91
240 22.25 24.00 20.06 40.47 50.20 24.44 5.78 43.56 27.95 21.31 2.19 27.95 5.78 18.22 21.31 43.12 46.25 54.09 41.63 43.75 41.26
245 25.00 27.50 22.57 45.53 56.48 27.50 7.00 49.01 31.45 23.98 2.47 31.45 7.00 20.50 23.97 49.74 52.25 61.25 47.93 50.84 47.43
250 27.81 29.81 25.08 50.59 62.75 30.55 7.04 54.45 34.94 26.64 2.74 34.94 7.04 22.78 26.64 54.86 57.34 67.52 52.84 55.31 52.29
255 30.63 33.38 27.58 55.65 69.03 33.61 8.32 59.90 38.43 29.30 3.01 38.43 8.32 25.05 29.30 60.33 63.41 73.80 58.04 61.32 57.41
260 33.38 35.63 30.09 60.71 75.30 36.66 8.30 65.34 41.93 31.97 3.29 41.93 8.30 27.33 31.97 64.68 68.75 80.96 62.45 65.63 61.89
265 36.13 37.88 32.60 65.77 81.58 39.72 8.27 70.79 45.42 34.63 3.56 45.42 8.27 29.61 34.63 70.24 74.09 87.23 67.65 71.10 67.05
270 38.94 41.69 35.11 70.83 87.85 42.77 9.80 76.23 48.92 37.30 3.84 48.92 9.80 31.89 37.29 76.34 80.50 94.57 73.40 76.83 72.60

FAN F G
H J M N P R S T
SIZE TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
225 12.58 12.81 13.05 20.48 11.88 15.64 20.48 13.32 12.11 12.58 12.81 12.35 1.56 4.80 2.24 0.69 18.92 7.07 5.13 2.57
230 15.10 15.38 15.66 24.50 14.26 18.67 24.50 15.98 14.53 15.10 15.38 14.81 1.69 5.09 1.77 0.81 20.48 9.65 6.65 3.32
235 17.62 17.94 18.27 27.99 16.64 20.94 27.99 18.65 16.95 17.62 17.94 17.28 1.69 5.52 1.88 0.81 20.16 10.30 7.30 3.65
240 20.13 20.50 20.88 31.84 19.01 23.72 31.84 21.31 19.37 20.13 20.50 19.75 1.81 5.81 1.88 0.81 26.41 10.87 7.87 3.94
245 22.65 23.06 23.49 36.22 21.39 27.25 36.22 23.97 21.79 22.65 23.06 22.22 2.13 6.29 2.04 0.81 21.04 11.51 8.51 4.26
250 25.17 25.63 26.10 39.71 23.77 29.53 39.71 26.64 24.22 25.17 25.63 24.69 2.13 6.95 2.41 0.81 23.34 12.09 9.09 4.55
255 27.68 28.19 28.71 43.21 26.14 31.80 43.21 29.30 26.64 27.68 28.19 27.16 2.38 7.62 2.29 1.06 29.74 14.67 10.67 5.34
260 30.20 30.75 31.32 47.59 28.52 35.33 47.59 31.97 29.06 30.20 30.75 29.63 2.38 8.28 2.66 1.06 39.86 15.25 11.25 5.62
265 32.71 33.31 33.93 51.08 30.89 37.61 51.08 34.63 31.48 32.71 33.31 32.10 2.38 8.95 3.04 1.06 35.21 15.83 11.83 5.91
270 35.23 35.88 36.54 55.63 33.27 41.39 55.63 37.29 33.90 35.23 35.88 34.57 2.38 9.61 2.94 1.06 37.58 18.40 13.34 6.67

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

32 TWIN CITY FAN - CATALOG 1300


DIMENSIONAL DATA
Arrangement 4, Design 3
J
D
2X Ø N
WHEN L>18.00
LOCATED AT L/2

H
E T
B
S

A
6X Ø N M
P
F G
Foundation
THD

D H H

A
A
B

F G F
D G
UBD
BHD
C
D

D
H FF H
H
E
E B
E

B A B A A

C F C F G
F G G

BAU TAD TAU

A B C E
ALL DIS-
FAN
CHARGES D
SIZE BHD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
EXCEPT
BHD1
325 13.75 16.38 12.40 24.85 30.80 15.11 5.28 26.76 17.05 13.01 1.36 17.05 5.28 11.10 13.01 26.88 29.85 34.33 25.59 28.37 25.28
330 16.50 18.63 14.87 29.81 36.95 18.13 5.31 32.11 20.45 15.61 1.63 20.45 5.31 13.31 15.61 33.30 35.38 40.49 31.58 34.10 31.11
335 19.25 21.38 17.35 34.78 43.11 21.15 5.84 37.46 23.86 18.21 1.90 23.86 5.84 15.53 18.21 37.68 40.82 47.00 35.82 38.67 35.40
340 22.00 24.75 19.83 39.75 49.27 24.17 7.00 42.81 27.27 20.81 2.17 27.27 7.00 17.75 20.81 43.27 46.50 54.05 40.97 44.25 40.45
345 24.75 27.00 22.31 44.72 55.43 27.19 7.03 48.16 30.68 23.41 2.44 30.68 7.03 19.97 23.41 48.31 51.55 60.20 46.06 49.72 45.51
350 27.50 30.50 24.79 49.69 61.59 30.22 8.31 53.52 34.09 26.02 2.72 34.09 8.31 22.19 26.02 54.96 57.69 67.25 52.31 55.91 51.58
355 30.25 32.75 27.27 54.66 67.75 33.24 8.34 58.87 37.50 28.62 2.99 37.50 8.34 24.41 28.62 60.57 63.29 73.41 57.58 60.76 56.75
360 33.00 36.50 29.75 59.63 73.91 36.26 9.87 64.22 40.91 31.22 3.26 40.91 9.87 26.63 31.22 64.41 69.13 80.63 61.41 66.29 60.68
365 35.75 38.75 32.23 64.60 80.07 39.28 9.90 69.57 44.32 33.82 3.53 44.32 9.90 28.85 33.82 70.64 74.10 86.79 67.08 71.81 66.10
370 38.50 42.00 34.71 69.57 86.23 42.30 10.93 74.92 47.73 36.42 3.80 47.73 10.93 31.07 36.42 76.73 80.39 93.65 72.90 77.34 71.85

FAN F G
H J M N P R S T
SIZE TAD THD TAU BAU BHD UBD TAD THD TAU BAU BHD UBD
325 12.46 12.78 13.09 20.58 11.53 16.10 20.58 13.01 11.83 12.46 12.78 12.15 1.56 4.92 2.24 0.69 17.67 7.30 5.37 2.68
330 14.96 15.33 15.71 23.99 13.84 18.31 23.99 15.61 14.20 14.96 15.33 14.58 1.69 5.23 1.77 0.81 19.03 9.93 6.93 3.46
335 17.45 17.89 18.32 27.75 16.15 21.03 27.75 18.21 16.57 17.45 17.89 17.01 1.81 5.69 1.88 0.81 26.88 10.63 7.63 3.81
340 19.94 20.44 20.94 32.05 18.45 24.50 32.05 20.81 18.93 19.94 20.44 19.44 2.13 6.00 1.88 0.81 24.62 11.25 8.25 4.13
345 22.43 23.00 23.56 35.45 20.76 26.72 35.45 23.41 21.30 22.43 23.00 21.87 2.13 6.44 1.97 0.81 27.79 11.94 8.94 4.47
350 24.93 25.55 26.18 39.75 23.07 30.19 39.75 26.02 23.67 24.93 25.55 24.30 2.38 6.75 1.97 0.81 21.97 12.56 9.56 4.78
355 27.42 28.11 28.79 43.16 25.37 32.41 43.16 28.62 26.03 27.42 28.11 26.73 2.38 7.06 1.47 1.06 27.84 15.19 11.19 5.59
360 29.91 30.66 31.41 47.63 27.68 36.13 47.63 31.22 28.40 29.91 30.66 29.16 2.38 7.48 1.58 1.06 37.35 15.81 11.81 5.91
365 32.40 33.22 34.03 51.04 29.98 38.35 51.04 33.82 30.76 32.40 33.22 31.59 2.38 8.07 1.85 1.06 32.83 16.44 12.44 6.22
370 34.90 35.77 36.65 55.15 32.29 41.57 55.15 36.42 33.13 34.90 35.77 34.02 2.38 8.67 1.67 1.06 35.04 19.06 14.00 7.00

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

WWW.TCF.COM 33
DIMENSIONAL DATA
Arrangement 4, Pedestal Dimensions
Design 1, Design 2 and Design 3
K

Foundation

GG

FAN FRAME FAN FRAME


K L GG
SIZE SIZE SIZE SIZE
143T 11.99 143T/145T 9.99 12.17
145T 12.74 _25 182T/184T 11.74 13.92
_25
182T/184T 12.99 213T/215T 13.49 15.67
213T/215T 14.99 145T 9.79 11.98
145T 12.54 182T/184T 11.54 13.73
182T/184T 12.79 _30 213T/215T 13.29 15.48
_30 213T/215T 14.79 254T/256T 17.29 19.48
254T/256T 19.42 284TS 17.79 19.98
284TS 21.29 182T/184T 11.83 14.02
182T/184T 13.08 213T/215T 13.58 15.77
213T/215T 15.08 254T/256T 17.58 19.77
_35
254T/256T 19.71 284T 19.33 21.52
284T 21.58 284TS/286TS 19.33 21.52
_35
284TS 21.58 324TS/326TS 21.08 23.27
286TS 21.96 213T/215T 13.96 16.14
324TS 23.58 254T/256T 17.96 20.14
326TS 24.46 284T/286T 19.71 21.89
213T/215T 15.46 286TS 19.71 21.89
_40
254T/256T 20.08 324T/326T 21.46 23.64
284T 21.96 324TS/326TS 21.46 23.64
286T 22.33 364TS/365TS 22.58 24.77
286TS 22.33 404TS/405TS 24.83 27.02
_40 324T 23.96 254T/256T 17.84 20.03
326T 24.83 284T/286T 19.59 21.78
324TS 23.96 324T/326T 21.34 23.53
326TS 24.83 326TS 21.34 23.53
364TS/365TS 25.46 _45 364T/365T 22.46 24.65
404TS/405TS 28.58 364TS/365TS 22.46 24.65
254T/256T 19.96 404TS/405TS 24.71 26.90
284T 21.84 444TS/445TS 28.34 30.53
286T 22.21 447TS 36.46 38.65
324T 23.84 256T 17.64 19.83
326T 24.71 284T/286T 19.39 21.58
_50
_45 326TS 24.71 284TS/286TS 19.39 21.58
364T/365T 25.34 324T 19.64 21.83
364TS/365TS 25.34 324T/326T 21.02 23.20
_55
404TS/405TS 28.46 364T 21.27 23.45
444TS 32.96 364T/365T 23.20 25.39
_60
445TS/447TS 32.96 404T/405T 25.45 27.64
256T 19.77 405T 25.25 27.44
_65
284T 21.64 444T/445T 28.88 31.07
286T 22.02 444T/445T 28.69 30.87
_50 _70
284TS 21.64 447T/449T 36.81 39.00
286TS 22.02
324T 23.64
324T 23.52
_55 326T 24.39
364T 25.02
364T/365T 26.07
_60
404T/405T 29.20
405T 29.00
_65
444T/445T 33.50
444T/445T 33.31 DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED
_70
447T/449T 42.06 DRAWINGS AVAILABLE ON REQUEST.

34 TWIN CITY FAN - CATALOG 1300


DIMENSIONAL DATA
Inlet/Outlet Dimensions

Ø BB, QTY -CC-


Ø X, QTY -Y- EQ. SP.
EQ. SP.
Ø AA

Ø V
DD
Ø U

Ø Z EE
Ø W INLET EXHAUST

FF
FAN
U V W X Y Z AA BB CC DD EE OUTLET FLANGE
SIZE
THICKNESS
125 10.00 5.50 8.50 0.88 8 7.50 6.00 0.75 4 2.22 2.19 0.25
130 11.00 6.56 9.50 0.88 8 7.50 6.00 0.75 4 2.74 2.62 0.25
135 13.50 7.69 11.75 0.88 8 9.00 7.50 0.75 8 3.11 3.06 0.25
140 13.50 8.75 11.75 0.88 8 10.00 8.50 0.88 8 3.63 3.50 0.25
145 16.00 9.88 14.25 1.00 12 10.00 8.50 0.88 8 4.14 3.94 0.25
150 16.00 10.94 14.25 1.00 12 11.00 9.50 0.88 8 4.53 4.37 0.25
155 19.00 12.06 17.00 1.00 12 11.00 9.50 0.88 8 5.05 4.81 0.31
160 19.00 13.13 17.00 1.00 12 13.50 11.75 0.88 8 5.56 5.25 0.31
165 21.00 14.25 18.75 1.13 12 13.50 11.75 0.88 8 6.08 5.69 0.31
170 23.50 15.31 21.25 1.13 16 13.50 11.75 0.88 8 6.60 6.12 0.31

FF
FAN
U V W X Y Z AA BB CC DD EE FLANGE
SIZE
THICKNESS
225 10.00 5.42 8.50 0.88 8 8.50 7.00 0.75 8 2.53 3.16 0.31
230 11.00 6.50 9.50 0.88 8 10.00 8.50 0.88 8 3.11 3.80 0.31
235 13.50 7.58 11.75 0.88 8 10.00 8.50 0.88 8 3.55 4.43 0.31
240 13.50 8.67 11.75 0.88 8 11.00 9.50 0.88 8 4.12 5.06 0.31
245 16.00 9.75 14.25 1.00 12 13.50 11.75 0.88 8 4.58 5.70 0.31
250 16.00 10.83 14.25 1.00 12 13.50 11.75 0.88 8 5.15 6.33 0.31
255 19.00 11.92 17.00 1.00 12 13.50 11.75 0.88 8 5.73 6.96 0.31
260 19.00 13.00 17.00 1.00 12 16.00 14.25 1.00 12 6.31 7.59 0.31
265 21.00 14.08 18.75 1.13 12 16.00 14.25 1.00 12 6.89 8.23 0.31
270 23.50 15.17 21.25 1.13 16 19.00 17.00 1.00 12 7.47 8.86 0.31

FF
FAN
U V W X Y Z AA BB CC DD EE FLANGE
SIZE
THICKNESS
325 10.00 5.52 8.50 0.88 8 10.00 8.50 0.88 8 2.77 3.98 0.31
330 11.00 6.63 9.50 0.88 8 10.00 8.50 0.88 8 3.39 4.78 0.31
335 13.50 7.75 11.75 0.88 8 11.00 9.50 0.88 8 3.88 5.58 0.31
340 13.50 8.87 11.75 0.88 8 13.50 11.75 0.88 8 4.50 6.38 0.31
345 16.00 9.98 14.25 1.00 12 13.50 11.75 0.88 8 5.00 7.17 0.31
350 16.00 11.10 14.25 1.00 12 16.00 14.25 1.00 12 5.62 7.97 0.31
355 19.00 12.22 17.00 1.00 12 16.00 14.25 1.00 12 6.25 8.77 0.31
360 19.00 13.34 17.00 1.00 12 19.00 17.00 1.00 12 6.88 9.56 0.31
365 21.00 14.38 18.75 1.13 12 19.00 17.00 1.00 12 7.50 10.36 0.31
370 23.50 15.50 21.25 1.13 16 21.00 18.75 1.13 12 8.13 11.16 0.31

DIMENSIONS ARE SUBJECT TO CHANGE. CERTIFIED DRAWINGS AVAILABLE ON REQUEST.

WWW.TCF.COM 35
ALTERNATIVE HIGH
PRESSURE FANS

TBR
Radial bladed with backplate and shroud
for low volume, high pressure applications.

Airflow to 8,000 CFM


Static pressures to 100" w.g.

Additional information can be found in


Catalog 1200.

MBO / MBR / MBW


Three (3) wheel designs

Airflow to 19,000 CFM


Static pressures over 125” w.g.

MBO - Open radial blades for handling hot, stick and


abrasive airstreams

MBR - Radial blades with front and back plate for


handling clean, hot, or particulate laden airstreams.
The most pressure and highest efficiency at a given
speed of any MB-Series fan

MBW - Radial blades with back plate and no front


plate to handle long, stringy, or fibrous materials.

Additional information can be found in Catalog 1400.

MBO Wheel MBR Wheel MBW Wheel

36 TWIN CITY FAN - CATALOG 1300


ALTERNATIVE HIGH
PRESSURE FANS

TBNA / TBNS
Turbo Pressure Blowers are used for applications re-
quiring lower volumes and higher air pressures.

Airflow to 5,400 CFM


Static pressures up to 57” w.g.

TBNS - Radial steel wheel designed to handle


fumes, light particulates, and temperatures up to
600°F (315°C)

TBNA - Backward inclined aluminum wheel de-


signed to handle clean-air applications up to 200°F

Additional information can be found in Catalog 1250.

TBA
Backward inclined blade for clean-air applications.

Airflow to 28,700 CFM


Static pressures to 70" w.g.

Additional information can be found in Catalog 1200.

BCN
Lower volume, higher pressure fan utilizing a high ef-
ficiency, backward curved, non-overloading blade de-
sign. Suitable for clean to light particulate-laden air.

Airflow to 75,000 CFM


Static pressures to 100” w.g.

Additional information can be found in Catalog 1450.

WWW.TCF.COM 37
TYPICAL SPECIFICATIONS

Model
HRO

Furnish and install Model HRO High Pressure Radial Pressure Blower as manufactured by Twin City Fan & Blower,
Minneapolis, Minnesota. Fans shall be specifically designed to handle specified volume and pressure to ensure rated
performance.
PERFORMANCE — Fans shall be tested in accordance with ANSI/AMCA Standard 210 (air performance) and AMCA
Standard 300 (sound performance) in an AMCA accredited laboratory.
HOUSING — Housings shall be made of a heavy gauge steel with continuously welded construction and braced with
structural members to eliminate any resonant vibration and provide smooth operation. A shaft seal, drain with plug,
flanged inlet and flanged outlet shall be provided as standard equipment. Inlet and outlet flanges shall be punched to
ANSI 125/150# pattern.
WHEEL — Wheels shall be of heavy gauge welded construction; riveted wheels are not acceptable. Blade orientation
shall be radial in design to handle hot, sticky and abrasive airstreams as well as clean air applications. HRO wheels shall
be open (no inlet shroud) to allow for particulate and vapor loading.
SHAFT (ARR 1 & 8 ONLY) — Shafts are to be solid material selected for AISI 1040 or 1045 hot rolled steel, accurately
turned, ground, polished, and ring gauged for accuracy. Shaft design shall be of sufficient diameter to allow the first
critical speed to be at least 1.43 times the maximum fan operating speed.
BEARINGS (ARR 1 & 8 ONLY) — Fans shall be supplied with heavy duty self-aligning grease lubricated anti-friction ball
or roller bearings to provide long bearing life. Bearing support members shall be fabricated of heavy steel designed to
insure maximum rigidity. Bearings shall be selected for a minimum average bearing life (AFBMA L-50) in excess of 200,000
hours at the maximum fan RPM.
FINISH AND COATING — The entire fan assembly, excluding the shaft, shall be thoroughly degreased and deburred before
application of a rust-preventative primer. After the fan is completely assembled, a finish coat of paint shall be applied to
the entire assembly. The fan shaft shall be coated with a petroleum-based rust protectant.
FACTORY RUN TEST — All fans prior to shipment shall be completely assembled. All fans up to 200 HP shall be test
run as a unit at operating speed or maximum RPM allowed for the particular construction type. Each wheel shall be
statically and dynamically balanced in accordance with ANSI/AMCA 204-96 “Balance Quality and Vibration Levels for Fans”
to Fan Application Category BV-3, Balance Quality Grade G6.3. Balance readings shall be taken by electronic type equip-
ment in the axial, vertical, and horizontal directions on each of the bearings. Records shall be maintained and a written
copy shall be available upon request.
GUARANTEE — Manufacturer shall guarantee the workmanship and materials for its HRO fans for at least one year from
startup, or eighteen months from shipment, whichever occurs first.

Twin City Fan

38 TWIN CITY FAN - CATALOG 1300


TYPICAL SPECIFICATIONS

Model
HRS

Furnish and install Model HRS High Pressure Radial Pressure Blower as manufactured by Twin City Fan & Blower,
Minneapolis, Minnesota. Fans shall be specifically designed to handle specified volume and pressure to ensure rated
performance.
PERFORMANCE — Fans shall be tested in accordance with ANSI/AMCA Standard 210 (air performance) and AMCA
Standard 300 (sound performance) in an AMCA accredited laboratory.
HOUSING — Housings shall be made of a heavy gauge steel with continuously welded construction and braced with
structural members to eliminate any resonant vibration and provide smooth operation. A shaft seal, drain with plug,
flanged inlet and flanged outlet shall be provided as standard equipment. Inlet and outlet flanges shall be punched to
ANSI 125/150# pattern.
WHEEL — Wheels shall be of heavy gauge welded construction; riveted wheels are not acceptable. Blade orientation
shall be radial in design to handle hot, sticky and abrasive airstreams as well as clean air applications. Wheel inlet side
shall be shrouded providing more efficiency and allow light particulate and vapor loading.
SHAFT (ARR 1 & 8 ONLY) — Shafts are to be solid material selected for AISI 1040 or 1045 hot rolled steel, accurately
turned, ground, polished, and ring gauged for accuracy. Shaft design shall be of sufficient diameter to allow the first
critical speed to be at least 1.43 times the maximum fan operating speed.
BEARINGS (ARR 1 & 8 ONLY) — Fans shall be supplied with heavy duty self-aligning grease lubricated anti-friction ball
or roller bearings to provide long bearing life. Bearing support members shall be fabricated of heavy steel designed to
insure maximum rigidity. Bearings shall be selected for a minimum average bearing life (AFBMA L-50) in excess of 200,000
hours at the maximum fan RPM.
FINISH AND COATING — The entire fan assembly, excluding the shaft, shall be thoroughly degreased and deburred before
application of a rust-preventative primer. After the fan is completely assembled, a finish coat of paint shall be applied to
the entire assembly. The fan shaft shall be coated with a petroleum-based rust protectant.
FACTORY RUN TEST — All fans prior to shipment shall be completely assembled. All fans up to 200 HP shall be test
run as a unit at operating speed or maximum RPM allowed for the particular construction type. Each wheel shall be
statically and dynamically balanced in accordance with ANSI/AMCA 204-96 “Balance Quality and Vibration Levels for Fans”
to Fan Application Category BV-3, Balance Quality Grade G6.3. Balance readings shall be taken by electronic type equip-
ment in the axial, vertical, and horizontal directions on each of the bearings. Records shall be maintained and a written
copy shall be available upon request.
GUARANTEE — Manufacturer shall guarantee the workmanship and materials for its HRS fans for at least one year from
startup, or eighteen months from shipment, whichever occurs first.

Twin City Fan

WWW.TCF.COM 39
INDUSTRIAL PROCESS AND
COMMERCIAL VENTILATION SYSTEMS
CENTRIFUGAL FANS | UTILITY SETS | PLENUM & PLUG FANS | INLINE CENTRIFUGAL FANS

MIXED FLOW FANS | TUBEAXIAL & VANEAXIAL FANS | PROPELLER WALL FANS | PROPELLER ROOF VENTILATORS

CENTRIFUGAL ROOF & WALL EXHAUSTERS | CEILING VENTILATORS | GRAVITY VENTILATORS | DUCT BLOWERS

RADIAL BLADED FANS | RADIAL TIP FANS | HIGH EFFICIENCY INDUSTRIAL FANS | PRESSURE BLOWERS

LABORATORY EXHAUST FANS | FILTERED SUPPLY FANS | MANCOOLERS | FIBERGLASS FANS | CUSTOM FANS

Twin City Fan

TWIN CITY FAN & BLOWER


WWW.TCF.COM

Twin City Fan


5959 TRENTON LANE N | MINNEAPOLIS, MN 55442 | PHONE: 763-551-7600 | FAX: 763-551-7601

©2018 Twin City Fan Companies, Ltd., Minneapolis, MN. All rights reserved. Catalog illustrations cover the general appearance of Twin City
Fan & Blower products at the time of publication and we reserve the right to make changes in design and construction at any time without notice.

You might also like