0% found this document useful (0 votes)
411 views46 pages

IRCMS Operation Manual E

Uploaded by

Philip Lo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
411 views46 pages

IRCMS Operation Manual E

Uploaded by

Philip Lo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 46

Smart Control Cloud System (SCCS)

Operation Manual
Version: V1.20210317

Copyright: Automatic Engineering Ltd.


TABLE OF CONTENT
LOGIN TO SCCS PLATFORM ....................................................................................................... 4
USER INTERFACE INTRODUCTION ............................................................................................. 5
Landing Page Introduction .................................................................................................... 5
Lighting Icon Status Introduction .......................................................................................... 5
Lighting System Control............................................................................................................. 6
Manual Control – Individual Control ..................................................................................... 7
Turn On/Dimming Control ................................................................................................. 9
Turn Off Control .............................................................................................................. 10
Individual Status Query ................................................................................................... 11
Manual Control – Group Control ......................................................................................... 12
Turn On/Off/Dimming Control ........................................................................................ 12
Automatic Control ............................................................................................................... 13
Building Lamp Groups & Lamp Assignment .................................................................... 13
Sunrise Sunset Time Parameters Setting ........................................................................ 14
Sun-based Tasks Setting .................................................................................................. 15
Regular Status Query Tasks Setting ................................................................................. 17
Ambient Lux Based Tasks Setting .................................................................................... 19
Tasks Sync ............................................................................................................................ 20
Lighting System Management ................................................................................................. 21
Adding New Hardware to System ....................................................................................... 21
Adding Concentrator ....................................................................................................... 21
Adding Luxmeter ............................................................................................................. 22
Adding Lamp Controller................................................................................................... 24
Placing Concentrators to map ......................................................................................... 25
Placing Lamp Controllers to map..................................................................................... 26
Testing Hardware Connectivity to Server............................................................................ 29
Testing Concentrator Connection ................................................................................... 29
Testing Lamp Controller Connection ............................................................................... 29
Removing Hardware from System ...................................................................................... 30
Removing Concentrators ................................................................................................. 30
Removing Luxmeters ....................................................................................................... 30
Removing Lamp Controller .............................................................................................. 31
Accessing Historical Data......................................................................................................... 32
Energy Related Historical Data ............................................................................................ 32
Viewing Energy Historical Data ....................................................................................... 32

2
Alarm Related Historical Data ............................................................................................. 33
Viewing Alarm ................................................................................................................. 33
Exporting Alarm Record................................................................................................... 34
Amending Alarm Parameters .......................................................................................... 34
User Management ................................................................................................................... 39
Adding Organization ............................................................................................................ 39
Adding User ......................................................................................................................... 41
Enabling Email Notification via Email .................................................................................. 44
Project Management ............................................................................................................... 45
Add Project .......................................................................................................................... 45
Edit Project .......................................................................................................................... 46

3
LOGIN TO SCCS PLATFORM
1. Access http://210.3.119.46:9001 with web browser.
2. In the login page, users may select their preferred display language at the upper
right corner.

3. Upon successful login, the following landing page shall appear. Users may logout
using the “sign out” button located at the upper right corner.

4
USER INTERFACE INTRODUCTION
Landing Page Introduction

• GIS: Map section which most of the lighting system operation located.
• STREET LIGHTING: Lighting hardware related setting page.
• ENERGY: View historical energy related data.
• EVENT ALARM: View alarm related data and settings.
• USER CENTER: Manage Users and Organizations settings.
• PROJECT: Manage project settings.

Lighting Icon Status Introduction

Icons filled with yellow represents dimming/on status.

Icons filled with black represents off status.

Icons filled with grey represents unknown status.

Icons with red border represents abnormal status, this would override the above mentioned
on/off/dimming status.

5
Lighting System Control
1. Select GIS to enter lighting control page

2. In the GIS page, there are several parts,


a. Yellow box: Refresh button for updating map and lighting status.
b. Red box: Alarm corner, showing outstanding alarms and access historical
alarms.
c. Blue box: Project icon, used to quick zoom into project.
d. Green box: Info panel, used to show detail information.

3. Click the “Lamma CEDD” project icon to zoom in. Lighting units under this project
shall appears.
4. Lighting system control consists of two parts,
a. Automatic: System controls all lights of a pier based on defined
time/ambient light level logic.
b. Manual: Users can control all lights or individual light.
5. Small circles represent lighting points while pillar box icons represent a group of
lighting points.

6
Manual Control – Individual Control
1. Click on any lighting point. Ballast info shall appear in the information panel on the
right.

7
2. Lighting point info:
a. Yellow box: Ballast ID, location.
b. Red box: Lighting switching lever.
c. Green box: Ballast electrical info and last upload time.

3. Select on/off/dimming as appropriate and confirm action.

8
Turn On/Dimming Control
Upon manual turn on/dimming action, lighting points on the map shall be filled with yellow.
Bulb icon in the information panel shall turn yellow and the lever next to it shall display the
current dimming level.

9
Turn Off Control
Upon manual turn off action, lighting points on the map shall be filled with black. Bulb icon
in the information panel shall turn grey and the lever next to it shall display the current
dimming level.

10
Individual Status Query
Select lighting points on map. Click “Query” button in the information panel to request
upload of current status and data from the lamp controllers. Upon successful query, “Query
time” shall be updated.

11
Manual Control – Group Control
Turn On/Off/Dimming Control
1. Select the Pillar box icon which represent a group of lighting points on the map.

2. Right click to show option menu. Under “Lamp”, there are three actions that could
be executed in group.
a. Red box: Turn on all lamps.
b. Yellow box: Turn off all lamps.
c. Green box: Set all lamps to a specific dimming level.

Group control might take some time to execute and receive status update. Please
allow not less than 4 minutes for the system to receive lamps response.

12
Automatic Control
Automatic control can only be executed in groups. Users can assign specific rules using time
and ambient light level to control behavior of automatic control. Automatic control is
responsible for daily operation.

Building Lamp Groups & Lamp Assignment


1. Select “Application” and “Group” on the left side of the map.

2. Select “Lamp Group” tab. (Red box)


Select Add sign. (Green box)
After building a empty group, click “Lamp”. (Blue box)

13
3. Click “Add Lamp”. (Blue box)
Select a concentrator which the ballast belong to. (Red box)
Unassign ballasts shall appear on right side panel. (Green box)

Sunrise Sunset Time Parameters Setting


1. Select “Application” and “Group” on the left side of the map.

2. Red box: Calculated Sunrise and Sunset time of Hong Kong based on the location of
the project.
Yellow box: Allow users to calibrate sunrise sunset time to meet their requirements.

14
After calibration, click save to update the on/off schedule.

Sun-based Tasks Setting


1. Select “Lamp Group” and select “Task”. Click “Add Task”.

15
2. Operation: Turn On/ Turn Off
Mode: SunRise
** SunRise and SunSet task execution time shall be set to 1 and 2 respectively to
avoid conflict.

3. Upon successful task add, two tasks shall appear.

16
Regular Status Query Tasks Setting
1. Select “Lamp Group” and select “Task”. Click “Add Task”.

2. Operation: Data Query


Mode: Schedule
**Suggested query interval would be at least 30 minutes

17
3. Upon successful task add, query tasks shall appear.

18
Ambient Lux Based Tasks Setting
1. Select “STREET LIGHTING” in landing page.

2. Select “COMMISSIONING” at the top and select “Luxmeter” from the left side menu.

3. Select the luxmeter to edit value and click “Batch Editing”.

a. On Light Value: If ambient lux is detected to be smaller than this value, lights
will be turned on.
b. Off Light Value: If ambient lux is detected to be greater than this value, lights
will be turned off.

** Off Light Value must be greater than the On Light Value.


Click OK to save and close the setting dialogue box.

19
Tasks Sync
Every concentrator installed in piers are responsible to save and dispatch tasks to its lamp
controllers.

1. Go to GIS, Application, Group. Select “Task Sync (PLC/Zigbee)”.


Select the concentrator and select “Sync now”.

2. Sync the data and tasks with the following sequence.


a. Select “Config (LCU Config)” and Yes.
b. Select “Sun Time” and Yes.
c. Select “RTU Lamp Task” and Yes.

After finishing syncing the above data and tasks, close the “Choose Sync Items”
popup.

3. Confirm whether all data and tasks are synced successfully. They are indicated as a
Tick if synchronization is successful. (Red box) Try again if any of these failed.

20
Lighting System Management
Adding New Hardware to System
Adding Concentrator
1. Go to STREET LIGHTING in the landing page, then select “DEPLOYMENT” at the top,
select “RTU&Cabinet” and then “Add Station”.

2. Input the following information in the popup.


a. RTU: FONDA-RTU200.
b. UID, Name in the right-side input box.
i. UID: It can be found on the label on the concentrator.
ii. Name: Suggested to be the name of the pier.

3. Click OK to add the concentrator to the system.

21
Adding Luxmeter
1. Go to STREET LIGHTING in the landing page, then select “DEPLOYMENT” at the top,
select “RTU&Cabinet” and then click the More button in the Luxmeter column.

2. Click “Add Luxmeter” in the popup, rename the photocell.


It is suggested to use the same name as the concentrator and add “photocell” at the
end for easy identification.

Press OK to save and close the popup.

22
3. Check if the added photocell presents.

23
Adding Lamp Controller
1. Go to STREET LIGHTING in the landing page, then select “DEPLOYMENT” at the top,
select “RTU&Cabinet” and then click the More button in the Pole column.

4. Click “Add Lamp” in the popup and input the following information in the popup.
a. LCU Model: FONDA-LCU13A.
b. UID, Name in the right-side input box.
i. UID: It can be found on the label on the lamp controller.
ii. Name: Suggested to be the same as the UID for identification.

Press OK to save and add.


5. Check if the added lamps present.

24
Placing Concentrators to map
1. Go to GIS map and right click on an empty space and enter “Edit Mode”.

2. Right click again on an empty space and select “Put station to map” and select the
concentrator you would like to put to the GIS map.

25
3. Drag the concentrator icon to the desired location. Right click on an empyt space
and click “Exit edit mode”.

4. Placement of concentrator finished.

Placing Lamp Controllers to map


1. Go to GIS map and right click on an empty space and enter “Edit Mode”.

26
2. Select the concentrator and right click on empty space. Select “Put lamp to map” to
put lamps to map one by one or select “Put lamps to map” to batch put lamps to
map.

3. Adjust the position of the lamps and click Tick sign above the lamps to finalize their
position.

27
4. Lamps placed on map.

28
Testing Hardware Connectivity to Server
Testing Concentrator Connection
1. Check the status of the concentrator on GIS map.

Concentrator online status display.

Concentrator unknown status display.


2. Perform data and status query.
a. Click on the concentrator icon.
b. Click Query in the information panel to request status update.
c. Check if the Query time of the concentrator has updated.

Testing Lamp Controller Connection


1. Perform data and status query.
a. Click on the ballast icon.
b. Click query in the information panel to request status update.
c. Check if the Query time of the ballast has updated.

29
Removing Hardware from System
Removing Concentrators
1. Go to STREET LIGHTING in the landing page, then select “DEPLOYMENT” at the top,
select “RTU&Cabinet” and then “Delete Station”.

2. Click Confirm in the popup to delete the concentrator from the system.

Removing Luxmeters
1. Go to STREET LIGHTING in the landing page, then select “DEPLOYMENT” at the top,
select “RTU&Cabinet” and then click the More button in the Luxmeter column.

2. Click “Delete Luxmeter” in the popup and confirm the action.

30
Removing Lamp Controller
2. Go to STREET LIGHTING in the landing page, then select “DEPLOYMENT” at the top,
select “RTU&Cabinet” and then click the More button in the Pole column.

6. Click “Delete Lamp” in the popup and confirm the action.

31
Accessing Historical Data
Energy Related Historical Data
Viewing Energy Historical Data
1. Go to “ENERGY” page in the landing page. Select “STATISTICS” at the top and
concentrator from the left side menu. Select the lamp controller name from
“Meter/terminal”. Select the time range to display on the same row.

32
Alarm Related Historical Data
Viewing Alarm
1. Go to “EVENT ALARM” in landing page. Select “REALTIME” at the top to view current
outstanding alarms.

2. Select “HISTORY” at the top to view historical alarms. Users may apply alarm and
time filters to display specific alarms history.

33
Exporting Alarm Record
1. Users can export the alarms in excel format using the “Export” button on the upper
right corner.

2. A ZIP file containing an excel file would be downloaded.

Amending Alarm Parameters


Lamp Failure and Power Failure
1. Go to STREET LIGHT in the landing page. Select COMMISSIONING at the top and
select LCU at the left menu.

34
2. Click “…” button in the Parameters coloumn of the concentrator. Select the lamp
controllers to be configured. Then click “Parameter setting” and “Alarm parameter
setting”.

3. Amend the threshold values of Lamp Failure Alarm and Power Failure Alarm.

4. Click Save and then click Submit.


Wait until the following popup appears and confirm all selected lamp controllers
are configured successfully.

35
Project-wide Alarm Settings
1. Concentrator related alarm settings
Over-voltage, Under-voltage, Offline alarms
a. Go to ALARMS in the landing page. Select SETTING tab at the top menu.

b. Select “Line overvoltage” or “Line undervoltage” alarms under Station for


configuration.
c. Edit the alarm parameters and click Save.

36
2. Lamp controllers related alarm settings
Over-current, Over-voltage, Under-voltage alarms
a. Go to ALARMS in the landing page. Select SETTING tab at the top menu.

b. Select “Lamp overvoltage” or “Lamp undervoltage” or “Lamp overcurrent”


alarms under Conventional Lamp for configuration.
c. Edit the alarm parameters and click Save.

37
3. Alarms setting Sync
a. Select SYNC tab, check the concentrator. Select “Sync Station Data”.

b. Wait for confirmation popup.

38
User Management
Adding Organization
1. Select “USER CENTRE” in the landing page.

2. Select “USER” at the top menu. Select “Organization” from the left menu. Click “Add
Organization”.

3. Under “Organization” tab, click “…” button of “Catalog” row. Select “Organizations”.

39
4. Input name of the organization, account, password and confirm password. Email is
required if users would like to receive email for alarms.
**This account is the administrator account of the organization**
5. Under “Project” tab, click “Select Project”. Select projects this organization have
right of access to.

40
6. Under “Role” tab, check all the items for this organization administrator account.

7. Click OK to save the setting.

Adding User
1. Select “USER CENTRE” in the landing page.

41
2. Select “USER” at the top menu. Select respective organization from the left menu
e.g., CEDD. Click “Add User”.

3. Input account, name, password and confirm password. Email is required if users
would like to receive email for alarms.

42
4. Under “Project” tab, click “Select Project”. Select projects this users have right of
access to.

5. Under “Role” tab, check all the items for this organization administrator account or
check appropriate items for monitoring only accounts.

6. Click OK to save the setting.

43
Enabling Email Notification via Email
1. Log into the user account. Click the user icon at the upper right corner to display
popup. Select “Notification Settings” tab. Check appropriate items for email
notifications.

2. Click save to save settings.

44
Project Management
Add Project
1. Go to “PROJECT” in landing page. Select “MANAGEMENT” at the top menu. Click
“Add Project”.

2. Input name, location and owned organization of the new project.

3. Click OK to save and close the popup.

45
Edit Project
1. Go to “PROJECT” in landing page. Select “MANAGEMENT” at the top menu. Select
the project and click “Edit Project”.

2. Amend the name, location and owned organization of the new project.

3. Click OK to save and close the popup.

46

You might also like