8B0C0160HW00.

001-1

8B0C0160HW00.001-1

1 General information
• Connections for supplying external 24 V devices
• Extensive protective measures

2 Order data
Model number Short description Figure
Wall mounting
8B0C0160HW00.001-1 ACOPOSmulti auxiliary supply module, 16 A, HV, wall mounting,
24VOut 1x 16 A, 1x 5 A
Required accessories
Terminal block sets
8BZ0C016000.001-1A Screw clamp set for ACOPOSmulti mod-
ules 8B0C0160Hx00.001-1: 1x 8TB3104.201M-11, 1x
8TB2104.2010-00, 1x 8TB2106.2010-00
Optional accessories
Fan modules
8BXF001.0000-00 ACOPOSmulti fan module, replacement fan for ACOPOSmulti
modules (8BxP / 8B0C / 8BVI / 8BVE / 8B0K)
Terminal blocks
8TB2104.2010-00 4-pin screw clamp, single row, spacing: 5.08 mm, label 1: num-
bered serially
8TB2106.2010-00 6-pin screw clamp, single row, spacing: 5.08 mm, label 1: num-
bered serially
8TB3104.201M-11 Screw clamp 4-pin, single-row, spacing: 7.62 mm, label 1: num-
bered serially, M keying: 1011

Table 1: 8B0C0160HW00.001-1 - Order data

3 Technical data
Model number 8B0C0160HW00.001-1
General information
Cooling and mounting method Wall mounting
Certification
CE Yes
KC Yes
UL cULus E225616
Power Conversion Equipment
DC bus connection
Voltage
Nominal 750 VDC
Operating range in continuous operation 260 to 800 VDC
Full continuous power 315 to 800 VDC
Continuous power consumption Max. 445 W
Power loss with continuous power 45 W
DC bus capacitance 220 nF
Design ACOPOSmulti backplane
24 VDC output
Continuous power 1) 400 W
Output voltage
DC bus voltage (UDC): 260 to 315 VDC 25 VDC * (UDC / 315)
DC bus voltage (UDC): 315 to 800 VDC 24 VDC ±6%
Continuous current 16 ADC
Reduction of continuous power depending on an No reduction
ambient temperature above 40°C
Reduction of continuous power depending on the
installation elevation
Starting at 500 m above sea level 40 W per 1000 m
Reduction of continuous power depending on the No reduction
cooling method
Startup delay Max. 1 s
Startup time Approx. 5 to 20 ms

Table 2: 8B0C0160HW00.001-1 - Technical data

Data sheet V 1.5 1

8B0C0160HW00.001-1
Model number 8B0C0160HW00.001-1
Residual ripple Typ. 50 mVSS
Terminal connection cross section of 24 VDC Out 1
output
Flexible and fine wire lines
With wire end sleeves 0.5 to 6 mm²
Approbation data
UL/C-UL-US 22 to 10
CSA 22 to 10
Terminal connection cross section of 24 VDC Out 2
output
Flexible and fine wire lines
With wire end sleeves 0.2 to 2.5 mm²
Approbation data
UL/C-UL-US 22 to 12
CSA 22 to 12
24 VDC internal system voltage supply
Output voltage 2) 25 VDC ±1.6%
Peak current (<4 s)
DC bus voltage (UDC): 350 to 800 VDC 21 ADC
Protective measures
Open circuit protection Yes
Overload protection Yes
Short circuit protection Yes
Feedback protection Max. 26 VDC (also when turned off)
Overtemperature protection Yes
Dielectric strength to ground ±50 VDC
Output/Input isolation SELV / PELV requirements
Design ACOPOSmulti backplane
24 VDC Out
Output voltage 2)
DC bus voltage (UDC): 260 to 315 VDC 25 VDC * (UDC / 315)
DC bus voltage (UDC): 315 to 800 VDC 24 VDC ±6%
Protection of 24 VDC Out 1 output 16 A (slow-blow) electronic, automatic reset
Protection of 24 VDC Out 2 output 5 A (slow-blow) electronic, automatic reset
Protective measures
Open circuit protection Yes
Overload protection Yes
Short circuit protection Yes
Feedback protection Max. 35 VDC (also when turned off)
Overtemperature protection Yes
Dielectric strength to ground ±50 VDC
Output/Input isolation SELV / PELV requirements
Design
24 VDC, COM Male connector
24 VDC Out 1 controller input
Wiring Sink
Electrical isolation
Input - 24 VDC Yes
Modulation compared to ground potential Max. ±50 V
Input voltage
Nominal 24 VDC
Maximum 30 VDC
Switching threshold
Low (24 VDC Out 1 is switched on) <5 V
High (24 VDC Out 1 is switched off) 3) >15 V
Input current at nominal voltage Approx. 10 mA
Switching delay
ON (24 VDC Out 1 is switched on) Max. 25 ms
OFF (24 VDC Out 1 is switched off) Max. 0.25 ms
Design Male connector
Terminal connection cross sections
Flexible and fine wire lines
With wire end sleeves 0.2 to 2.5 mm²
Approbation data
UL/C-UL-US 30 to 12
CSA 22 to 12
Operating conditions
Permitted mounting orientations
Hanging vertically Yes
Lying horizontally Yes
Standing horizontally No

Table 2: 8B0C0160HW00.001-1 - Technical data

2 Data sheet V 1.5

 8B0C0160HW00.001-1
Model number 8B0C0160HW00.001-1
Installation at elevations above sea level
Nominal 0 to 500 m
Maximum 4) 4000 m
Degree of pollution in accordance with EN 2 (non-conductive pollution)
61800-5-1
Overvoltage category in accordance with EN III
61800-5-1
EN 60529 protection IP20
Environmental conditions
Temperature
Operation
Nominal 5 to 40°C
Maximum 55°C
Storage -25 to 55°C
Transport -25 to 70°C
Relative humidity
Operation 5 to 85%
Storage 5 to 95%
Transport Max. 95% at 40°C
Mechanical characteristics
Dimensions 5)
Width 53 mm
Height 317 mm
Depth
Wall mounting 263 mm
Weight Approx. 3.2 kg
Module width 1

Table 2: 8B0C0160HW00.001-1 - Technical data

1) Valid in the following conditions: 750 VDC DC bus voltage, 55°C ambient temperature, installation elevation <500 m above sea level, no derating due to
cooling type.
2) When a fault occurs, the output voltage is limited to a max. of 60 VDC.
3) The output and any connected loads are not actively discharged when switched off.
4) Continuous operation at elevations ranging from 500 m to 4000 m above sea level is possible (taking the specified continuous current reductions into
consideration). Requirements that go above and beyond this must be arranged with B&R.
5) These dimensions refer to the actual device dimensions including the respective mounting plate. Make sure to leave additional space above and below the
devices for mounting, connections and air circulation.

4 Status indicators
Status indicators are located on the black cover of each module.

Power supply 24 V 24 V 24 V Out

Cxxxx

Overload ERR ERR Error 24 V Out

Figure 1: Indicator groups for auxiliary supply modules with 24 V Out (8B0C0xx0Hx00.00x-1)

Data sheet V 1.5 3

8B0C0160HW00.001-1

4.1 LED status - Auxiliary supply modules with 24 V Out

Status indicator group Labeling Color Function Description
Power supply 24 V Green 24 V OK The 24 VDC internal system supply voltage is within the permis-
sible tolerance
Overload ERR Red Overload The module is not supplied via the DC bus voltage. 1)
The 24 VDC internal system supply voltage is outside of the per-
missible tolerance (overload, overtemperature, short circuit, etc)
24 V Out 24 V Green 24 V Out OK One of the switchable 24 VDC outputs is active and the output
voltage is within the permissible tolerance
The 24 VDC internal system supply voltage is within the permis-
sible tolerance
ERR Red 24 V Out error The 24 VDC internal system supply voltage is outside of the per-
missible tolerance (overload, overtemperature, short circuit, etc)
At least one of the switchable outputs is active and the resettable
fuse has been tripped for one or more switchable outputs.

Table 3: LED status - 8B0C auxiliary supply modules with 24 V Out

1) The module is enabled via the input CR_OK, no electrical contact to the backplane module - check bottom mounting screws.

5 Dimension diagram and installation dimensions

Permitted
mounting orientations

3)
2)

1)

Hanging vertically

Lying horizontally

Impermissible
mounting orientations

Standing horizontally

2)
2)

Hanging horizontally

Figure 2: Dimension diagram and installation dimensions

1) n ... Number of slots on the mounting plate
2) For proper air circulation, at least 60 mm clearance must be available above the mounting plate as well as below the module.
To ensure that the fan modules in the mounting plate can be replaced easily, at least 250 mm clearance must be available below the module.
3) nnnn indicates the number of slots (e.g. 0160 refers to 16 slots).

4 Data sheet V 1.5

 8B0C0160HW00.001-1

6 Wiring
6.1 Pinout overview - 8B0C0160Hx00.001-1, 8B0C0320Hx00.002-1

(=8B0K.../ X1: CR_OK Out)

(=8B0K.../ X1: CR_OK In)

(=8B0C.../ X1: COM(5.6))

(=8B0C.../ X1: COM(5.6))

(=8BxP.../ X1: COM(5.6))

(=8B0K.../ X1: COM(12))

(=8B0K.../ X1: COM(11))
(=8B0C.../ X1: CR_OK)
(=8B0C.../ X1: CR_OK)
(=8BxP.../ X1: CR_OK)

Figure 3: Pinout overview - 8B0C0160Hx00.001-1, 8B0C0320Hx00.002-1

6.2 X1 connector - Pinout

X1 Pin Name Function
1 --- ---
1
2 --- ---
2 3 COM (5, 6)) DC bus ready 0 V
3 4 COM (5, 6)) DC bus ready 0 V
4
5 CR_OK DC bus ready
6 CR_OK DC bus ready
5

Table 4: X1 connector - Pinout

6.3 X2 connector - Pinout

X2 Pin Name Function
1 COM (2) +24 V output 2 0 V
1
2 +24V Out 2 +24 V output 2
2 3 COM (4) Disable +24 V output 1 0 V
3 4 Disable +24V Out 1 Disable +24 V output 1
4

Table 5: X2 connector - Pinout

Data sheet V 1.5 5

8B0C0160HW00.001-1

6.4 X3 connector - Pinout

X3 Pin Name Function
1 +24V Out 1 +24 V output 1
2 +24V Out 1 +24 V output 1
3 COM (1, 2)) +24 V output 1 0 V
4 COM (1, 2)) +24 V output 1 0 V

4 3 2 1

Table 6: X3 connector - Pinout

Information:
B&R recommends grounding both COM connections (1, 2) on the X3 plug to achieve a defined rela-
tionship between the signal ground and ground potential. Alternatively, the COM (2) connection can
also be grounded on the X2 connector.

6.5 Input/output circuit diagram

Filters

Figure 4: Input/output circuit diagram - 8B0C0160Hx00.001-1, 8B0C0320Hx00.002-1

6 Data sheet V 1.5