BULLETIN NO.
SERVICE PARTS LIST 54-22-1029
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS REVISED BULLETIN DATE
54-22-1028 Jan. 2018
D. I. DIE GRINDER
WIRING INSTRUCTION
STARTING
CATALOG NO. 5192 SERIAL NO. 669F 58-01-0309
EXAMPLE:
00 0 Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
FIG. PART NO. DESCRIPTION OF PART NO. REQ. Collets
The collet must be attached to the collet nut before it is put into the collet shaft. Be sure that the size of
1 44-76-0130 Cord Protector (1) the collet matches the size of the bit shank being used. If the wrong size bit shank is used, the collet
2 22-64-0215 Cord Set (1) may break. For attaching or detaching the collet nut to the collet, follow the illustrated instructions.
3 12-20-0900 Service Nameplate Kit (1) Attaching Collet to Collet Nut
4
31-55-0157 Trigger Cover (1)
5 06-82-7409 8-16 x 1/2" Pan Hd. Plastite T-20 Screw (1) Fig. 1 Fig. 2
6 34-40-4015 O-Ring (2)
7 23-66-2190 Switch (1)
8 22-20-0691 Left Brush Holder (1)
9 06-82-7270 8-16 x 5/8" Pan Hd. Slt.Plastite T-20 Scr. (3)
10 31-15-0143 Motor Housing Cover (1)
12 42-38-0181 Rubber Bumper (2) To assemble, place the narrow end of the collet Position nut squarely over collet with the smaller
on an even surface. Take the nut and place it over opening of the nut facing up (Fig. 2).
13 22-20-0692 Right Brush Holder (1) the collet (Fig. 1).
14 23-52-0240 Brush Spring (2)
15 22-18-0710 Carbon Brush (2) Fig. 3 Fig. 4
16 31-50-0426 Motor Housing (1)
17 02-04-0845 Ball Bearing (1)
18 18-07-7100 120 Volt Field (1)
19 06-82-7430 8-16 x 2-1/8" Pan Hd. Plastite T-20 Scr. (2)
20 16-10-7100 120 Volt Armature (1)
21 22-84-0680 Fan (1) Snap nut and collet together by firmly applying To remove collet from nut, hold nut firmly with one
22 34-60-0920 Ball Brg. Retaining Ring (1) downward pressure into assembly with palm of hand and press the collet to one side with the other
23 06-82-5275 Pan Head Screw (2) hand (Fig. 3). hand (Fig. 4).
24 02-04-1207 Ball Bearing (1)
25 28-28-1906 Diaphragm Service Kit (1) FIG. PART NO. DESCRIPTION OF PART NO. REQ.
26 32-75-2880 Spindle Gear (1) 38 23-16-1670 Commutator Insulator (1)
27 02-04-0845 Ball Bearing (1) 49-96-4040 1/2" Open End Wrench (1)
28 45-88-7550 Finger Washer (1) 49-96-4090 11/16" Open End Wrench (1)
29 28-50-7722 Spindle Housing (1)
30 06-82-7296 7-18 x 1" Pan Hd. Slt. Plastite T-20 Scr. (4) FIG. LUBRICATION
31 02-04-1005 Ball Bearing (1) 29 1/4 Oz. Type "G" Grease, No. 49-08-4140.
32 38-50-5211 Spindle Shaft (1)
33 48-68-0031 1/4" Collet Nut (1)
34 34-80-5090 Retaining Ring (1) MILWAUKEE ELECTRIC TOOL CORPORATION
35 48-66-0975 1/4" Collet (1) 13135 W. LISBON RD., BROOKFIELD, WI 53005
36 28-28-1901 Diaphragm (1) Drwg. 1
