Scribd
Upload
37 views2 pages

New Text Document

spanning tree test paper 3

Uploaded by

piyush singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
37 views2 pages

New Text Document

spanning tree test paper 3

Uploaded by

piyush singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

11.

What command is used to view the IPv6-to-MAC-address resolution table on a


Cisco router?
A. show ip arp
B. show ipv6 arp
C. show ip neighbors
D. show ipv6 neighbors
E. show arp
12. An IPv6 ARP entry is listed as with a status of REACH. What can you conclude
about the
IPv6-to-MAC-address mapping?
A. The interface has communicated with the neighbor address and the mapping is
current.
B. The interface has not communicated within the neighbor reachable time frame.
C. The ARP entry has timed out.
D. IPv6 can reach the neighbor address but the addresses has not yet been resolved.
13. Serial0/1 goes down. How will EIGRP send packets to the 10.1.1.0 network?
Corp#show ip eigrp topology
[output cut]
P 10.1.1.0/24, 2 successors, FD is 2681842
via 10.1.2.2 (2681842/2169856), Serial0/0
via 10.1.3.1 (2973467/2579243), Serial0/2
via 10.1.3.3 (2681842/2169856), Serial0/1
A. EIGRP will put the 10.1.1.0 network into active mode.
B. EIGRP will drop all packets destined for 10.1.1.0.
C. EIGRP will just keep sending packets out s0/0.
D. EIGRP will use s0/2 as the successor and keep routing to 10.1.1.0.
14. What command produced the following output?
via FE80::201:C9FF:FED0:3301 (29110112/33316), Serial0/0/0
via FE80::209:7CFF:FE51:B401 (4470112/42216), Serial0/0/1
via FE80::209:7CFF:FE51:B401 (2170112/2816), Serial0/0/2
A. show ip protocols
B. show ipv6 protocols
C. show ip eigrp neighbors
D. show ipv6 eigrp neighbors
E. show ip eigrp topology
F. show ipv6 eigrp topology
15. You need to troubleshoot an adjacency between two EIGRP configured routers?
What should
you look for? (Choose four.)
A. Verify the AS numbers.
B. Verify that you have the proper interfaces enabled for EIGRP.
C. Make sure there are no mismatched K-values.
D. Check your passive interface settings.
E. Make sure your remote routers are not connected to the Internet.
F. If authentication is configured, make sure all routers use different passwords.
16. You have two OSPF directly configured routers that are not forming an
adjacency. What
should you check? (Choose three.)
A. Process ID
B. Hello and dead timers
C. Link cost
D. Area
E. IP address/subnet mask
17. When do two adjacent routers-enter the 2WAY state?
A. After both routers have received Hello information
B. After they have exchanged topology databases
C. When they connect only to a DR or BDR
D. When they need to exchange RID information
18. Which type of LSAs are generated by ABRs and referred to summary link
advertisements
(SLAs)?
A. Type 1
B. Type 2
C. Type 3
D. Type 4
E. Type 5
19. Which of the following is not provided by the AH portion of IPsec?
A. Integrity
B. Confidentiality
C. Authenticity
D. Anti-reply
20. Which

You might also like