RAC SERVICING(DOMRAC NC II)
Module Content
Unit of Competency: Install Domestic Refrigeration and Air-conditioning Unit
(DOMRAC) NC II
Module Title: INSTALLING WINDOW TYPE AIR-CONDITIONING / DOMESTIC REFRIGERATION
UNITS
Module Discriptor: This module covers the knowledge, skills and attitudes required to safety install,
test a window type air-conditioning /domestic refrigeration units.
Training Duration: 60 Hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of the module, the trainees/students should be able to:
LO1.Conduct survey
LO2.Install electrical circuit
LO3.Install window type air-con
LO4.Conduct performance test
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
LO1. CONDUCT SURVEY
ASSESSMENT CRITERIA:
1. Site conditions and installation requirements are assessed according to manufacturer’s
specification and prevailing codes and ordinances.
2. Tools, equipment and materials needed for installation are determined according to site
conditions and site installation requirements.
3. Survey result is recorded in installation, testing and commissioning (ITC) report according to
enterprise policy.
CONTENTS:
Dom RAC Installation Requirements
- Air circulation/ventilation requirements
- Drain disposal requirements
- Power supply requirements
- Structural and architectural requirement
- Provision for serviceability
Tools equipment and materials needed in installing DomRAC
Survey Inspection Report
CONDITIONS:
Student / trainees must be provided with the following:
Learning Materials Tools Training Facility
- Work plan - Pull-push rule - Access to survey
- Brochure site
- Catalogue
- L.E on Drawing electrical
& mechanical diagrams
- Fundamentals of
refrigeration
Supplies and Materials
- Marker/ pen
- Bond paper/Survey
Form
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
METHODOLOGIES:
Lecture
Self-paced instruction
Film viewing
ASSESSMENT METHODS:
Interview
Written examination
Observation with questioning
RPL
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
LO2. INSTALL ELECTRICAL CIRCUIT
ASSESSMENT CRITERIA:
1. Perform roughing-in activities according to appropriate provision in PEC.
2. Electrical cabling and wiring devices of correct load carrying capacity are selected and safely
installed in line with manufacturer's instructions
3. Power wiring is installed in accordance with the Philippine Electrical Code (PEC)
4. Test electrical circuit in accordance with PEC
CONTENTS:
Wires and cables used in electrical wiring
Classes of outlet/switches boxes used in electrical wiring (PEC)
Enclosure and their conditions for use
Types of devices used in electrical wiring
Identifying wall plugs and masonry bolts
Drilling into masonry using portable electrical drill
Marking out using spirit level /water level
Use of electrical measuring instruments
Testing electrical circuits
CONDITIONS:
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
Student / trainees must be provided with the following:
Equipment Instruments Learning Materials
- Portable electric - Test light - Work plan
drill - Multi-tester - Brochure
- Portable disc - Megger - Safety Practices
grinder Supplies and Materials - Drawing
Tools - Masonry drill Mechanical/electrical
- Hammer - Hacksaw - diagrams, types of wires,
- Set of pliers - Electrical railways - insulations, conduits,
- Spirit level, - Circuits breaker - wiring devices
water hose - Masonry(ex.cement, sand, etc.) - Work safety
- Plumb bob - Expansion Bolt/Box - Proper handling of
- Cross cut / rip - Electrical Cable/ Conductor tools/equipment
saw - Convenience Outlet - Communicating
- Push pull rule effectively
- Tri-square
- Wire stripper
- Electrician knife
METHODOLOGIES:
Self-paced instruction
Film viewing
Direct laboratory experience
Group discussion
ASSESSMENT METHODS:
Interview
Written examination
Demonstration with questioning
LO3. INSTALL WINDOW TYPE AIRCON
ASSESSMENT CRITERIA:
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
1. Unit and equipment/components are prepared based on work procedures
2. Bracket, hangers and frames are installed in accordance with manufacturer’s
recommendation.
3. Unit is positioned and leveled in line with manufacturer's instructions
4. Sealing materials are installed to ensure an air tight seal around the unit in line with
manufacturer's instructions
5. Condensate drain is installed in accordance with manufacturer’s recommendation.
6. Safe manual handling techniques are employed in line with enterprise OH&S procedures
7. 5’s is exercised in line with enterprise policy
CONTENTS:
Refrigeration cycle
Air-con/Refrigerator components and accessories
Sealant and insulation
Fastening devices
WAC installation procedure
Basic plumbing
- Types of PVC drain pipes
- Types of PVC fittings
Safety practices
CONDITIONS:
Student / trainees must be provided with the following:
Equipment Tools
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
- Portable electric drill - Hacksaw
- Portable disc grinder - Push-pull rule
- Welding equipment - T-square
- air-con unit - Plumb bob
Supplies and Materials - Spirit level
- Masonry drill bit - Water hose
- Fastener - Cross-cut/ rip saw
- Hacksaw blade - Chisel
- Marker/ pen, pentel - Hammer
- Bond paper - Masonry tools e.g. trowel square,
etc.
METHODOLOGIES:
Self-paced instruction
Film viewing
Direct laboratory experience
Group discussion
ASSESSMENT METHODS:
Interview
Written examination
Demonstration with questioning
LO4. CONDUCT PERFORMANCE TEST
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
ASSESSMENT CRITERIA:
1. Voltage and current are measured according to unit power requirements.
2. Air temperature and velocity are measured based on unit specifications.
3. Sounds and vibration are checked based on unit specifications
4. Installation, testing and commissioning (ITC) report is prepared in line with enterprise policies
and procedures.
CONTENTS:
Measuring air circulation and velocity
- Velometer/anemometer
Temperature testing
- Thermometer
Current and voltage measurement
- Clamp ammeter
CONDITIONS:
Student / trainees must be provided with the following:
Equipment Tools
- Refrigerator - Screwdriver
- air-con unit
Supplies and Materials
- Marker/ pen, pentel
- Bond paper
Instrument
- Velometer /anemometer
- Thermometer
- Clamp ammeter
- Multi-tester
METHODOLOGIES:
Lecture
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
RAC SERVICING(DOMRAC NC II)
Self-paced instruction
Film viewing
Direct laboratory experience
Group discussion
ASSESSMENT METHODS:
Interview
Written examination
Demonstration with questioning
TESDA Regional Training Center Ronald Dela Bajan – TM1 Revision 00
