Foreword

Thank you very much for purchasing PI8000,PI8100 Family Frequency Inverters.
This family is designed based on the experience of POWTRAN Company in the
professional manufacture and sale of the products, and suitable for general-purpose
machine, fan/pump drive, high frequency drive and heavy load machine.
This User’s Manual provides the users with the instructions on the installation,
parameter setting, fault diagnosis, routine maintenance and necessary precautions.
Please read the Manual carefully before the installation of the product in order to
ensure that it can be correctly installed and operated.
This product adopts the advanced sensorless vector control technology,combined
with the application of inverter technology in China features to achieve
high-performance V/F control (dead-time compensation + auto-torque upgrade + Slip
Compensation) and high-performance non-sense vector control, and
high-performance speed sensorless vector control.
This User’s Manual includes PI8000/PI8100, the general purpose control and
special purpose control . The general purpose control ha F,G ,M and H; The special
purpose control has S,T and Z:
F: FLOW LOAD
G:GENERAL LOAD
M: MEIDDLE LOAD
H: HEAVY LOAD.
S: TEXDRIVE.
T: WINDLASS.
Z: JETDRIVE.
Please contact the local dealers or directly contact our company.
Please keep this user’s manual in good condition, for it will be helpful to the
repair, maintenance, and applications in the future.
For information about other product, please visit our website:
http://www.powtran.com.
 CONTENTS

Forewords.

Contents

Section I. Inspection and Safety Precautions ....................... 1

Section II. Installation & Standby Circuit ............................. 4

Section III. Operating keyboard ........................................... 14

Section IV. Test running ...................................................... 22

Section V Parameter function table ........................................ 25

Section VI. Fault Diagnosis and Solutions ......................... 100

Section VII Standard Specifications ..................................... 103

Section VIII. Maintenance ................................................... 120

Section IX. Options ........................................................... 122

Section X Quality Assurance ................................................ 126

Appendix 1. RS485 communication protocol..................... 128

Appendix 2: Instruction of the proportional linkage function 138

Appendix 3. PG instruction .................................................. 142

Appendix 4 Converter water supply controller instruction .... 143

 Section I Inspection & Safety Precautions Section II Inspection & Standby Circuit

Section I. Inspection & Safety Precautions 1-1-3 Name plant Instruction 2

POWTRAN PI8000 frequency inverters have been tested and inspected before TYPE: PI8100 004G3
SOURCE: 3φ 380V 50-60Hz
leaving the manufacturer. Before unpacking the product, please check if its package is OUTPUT: 4KW 8.5A 0.00-800.0Hz
damaged due to careless transportation, and if the specifications and type of the
product complies with the order. Please contact the supplier of POWTRAN products Z0901A00001
POWTRAN TECHNOLOGY CO.,LTD.
if any problems are found.
1-1. Inspection after Unpacking
1-1-4 Model description 2：
※ Inspect that the contents are complete (one Operation Manual).
※ Check the nameplate on the side of the frequency inverter to ensure that the
product you have received is right the one you ordered.
1-1-1 Instructions on name plate: (giving 132kW/380V as example)

TYPE: PI7800 132G3

SOURCE: 3φ 380V 50-60Hz
OUTPUT: 132KW 250A 0.00-800.0Hz

Z0501A00001
POWTRAN TECHNOLOGY CO.,LTD.

1-1-2 Model designation:

1-2. Safety Precautions
※ Never connect the A.C. power supply to the output terminals (U, V, W) of the
frequency inverter.
※ Fix and lock the panel before supplying power so as to avoid the danger caused
by the poor capacity or other components inside the inverter.
※ After the power supply is switched on, do not perform wiring or check, etc.
※ Don’t touch the circuit boards or its parts or components in the inverter when it
is powered, so as to avoid danger of electric shock.
※ If the power supply is switched off, do not touch the PCB or other parts inside
the inverter within 5 minutes after the keyboard indicator lamp goes off, and you
must check by using the instrument that the inverter has completely discharged
all its capacity before you start to work inside the inverter. Otherwise, there will
be the danger of electric shock.
※ The static electricity in human body will cause serious damage to the MOS field
effect transistor in the inverter. Please keep your hands away from the PCB,
IGBT and other internal parts before taking actions to prevent static electricity.
Otherwise, faults may be caused.
※ In use, the earthing terminal (E or ) of the frequency inverter must be
grounded to the earthing connections correctly and securely according to the
national electrical safety specifications and other applicable standards.

1 2
 Section I Inspection and safety precautions Section II Inspection & Standby Circuit

※ Please don’t shut off the unit by turning off the power supply. Turn off the Section II. Installation & Standby Circuit
power supply after the motor has stopped its operation.
※ Meet CE standard with EMI filter.
2-1. Conditions for Use
1-3. Application
1) Ambient temperature -10℃~40℃.
※ Powtran inverter is generally applied to 3 phase AC asynchronism motors.
2) Avoid electromagnetic interference and keep the unit away from the interference
※ Powtran inverter is applied to the admisive occasion, the occasion where is not source.
admissive may lead to fire, electric shock, explosion and so on. 3) Prevent dropping water, steam, dust, powder, cotton fiber or fine metal powder
※ If the inverter seizes up when it is applied to the equipment which may lead from entering it.
danger (e.g. lift tools of transportation, aviation system, saftety equipment, etc), 4) Prevent oil, salt and corrosive gas from entering it.
it should be managed carefully. Do inquire the factory when it happens. 5) Avoid vibration.
6) Avoid high temperature and moisture and avoid being wetted due to raining,
Only the well-trained personnel are allowed to use this unit, and with the humidity below 90%RH (not dewing).
such personnel must read through the parts of this manual relating
7) Prohibit the use in the dangerous environment where inflammable or
to the safety, installation, operation and maintenance before using combustible or explosive gas, liquid or solid exists.
the unit. The safe operation of this unit depends on correct transport,
2-2. Installation
installation, operation and maintenance!
The frequency inverter must be installed by wall hooking in the indoor room
with adequate ventilation, with enough space left between it and the adjacent objects
or damper (walls) surrounding it, as shown in the below figure:

150MM
OUT OUT AIR

50MM 50MM

47,27
150MM
IN IN

2-3. Wiring
The wiring of frequency inverter includes two parts: main circuit and control
circuit. The user must ensure correct connections according to the following
connection diagram.
2-3-1. PI8000 Diagram
1. Wiring diagram 11KW~15KW and below (8N3)

3 4
 Section II Inspection & Standby Circuit Section II Inspection & Standby Circuit

2.Wiring diagram 18.5kW～355kW（8N4 /8N5 /8N6 /8N7 /8N8 /8NA /8NB）

5 6
 Section II Inspection & Standby Circuit Section II Inspection & Standby Circuit

2-3-2 PI8100 Diagram 2-4 Main Circuit Terminals（G Series）

1. Wiring diagram 11KW and below（7N2 /7N3 /7N4）
2-4-1 PI8000 Main Circuit Terminals
1．11kW～15kW（380V）Main Circuit Terminals

2．18.5～22kW（380V）Main Circuit Terminals

3．30～160kW（380V）Main Circuit Terminals

Note：DC+1/DC+2 Standard setting is short circuit; if it is with external reactance, please

disconnect and then connect it.
4．187～355kW（380V）Main Circuit Terminals

7 8
 Section II Inspection & Standby Circuit Section II Inspection & Standby Circuit

DI3 DI3 Input Terminal Enter a valid polarity can be

DI4 DI4 Input Terminal controlled by o47
DI1～DI4Drive model can be
DI5 DI5 Input Terminal controled by JP4
DI6 DI6 Input Terminal Above 11KW:
DI7 DI7 Input Terminal DI5～DI8 Drive model can be
controled by PLC output terminal
DI8can as digital pulse input
Below 11KW:
DI8 DI8 Input Terminal DI5～DI6 Drive model can be
Note:The above KW categaries are for G type inverter. controled by PLC output terminal
DI6 can as digital pulse input
2-4-2 PI8100 Main Circuit Terminals PLCControl DI5～DI8 Drive model
1．7.5kWbelow（380V）Main Circuit Terminals PLCControl Drain Drive ：PLCconnect 24VDC or
PLC
Terminal externa lpower
Source Drive：PLC connect COM
24V Power positive The biggest output 24V/200mA, Can
Assistant
not connect COM with GND in any
Power COM Common situation
Open Collector signal when the output
SPA/COM Output signal 1
action (24VDC/50mA)
Common terminal COM,the output
SPB/COM Output signal 2
Output function can set by o21,o22
Note：The above KW categaries are for G type inverter. signal TA1-TC1open,TB1-TC1close,the
TA1/TB1/TC1 Output signal 3
output function can set by o23
2-4-3 Terminal Function
TA2-TC2open ,TB2-TC2close,the
Terminal Description Functions TA2/TB2/TC2 Output signal 4
output function can set by o24
R/L1 +10V,GND power +10V,50mA,GND
Power input for Connected to 3-phase power
S/L2 JP5 cut/JP3 1-2：－10V～＋10V
frequency inverter (Single input connected to R ,T)
T/L3 JP5 cut/JP3 2-3：0~10V
JP5 connect: 0~20mA can be regulated
Grounding point Grounded to the earth
AI1 Voltage input signal o00/o01 Set the input voltage / current
Connection point for range
B1,B2 Connect brake resistance
braking resistance o06/o07 Set the input signal
U/T1 corresponding to set value
V/T2 3 Phase Output Connected to 3-phase motor JP6cut：0~10V
Analog JP6connect：0~20mA can be regulated
W/T3 o02/o03can set input voltage/ current
input
DC+1,DC- DC Bus output Connect the brake resistance AI2 Current input signal arrange
signal
DC+1,DC+2 DC reactance Connect DC reactance o08/o09 Set the input signal
corresponding to set value

JP7cut：0~10V
2-5 Control Circuit Terminals JP7connect：0~20mA can be regulated
2-5-1 Control Circuit Terminals Description Current feed back input o04/o05 can set input voltage/ current
AI3
Classify Terminal Description Functions signal arrange
DI1 DI1 Input Terminal o10/o11 Set the input signal
Input Multi-functions input terminal。For
corresponding to set value
signal DI2 DI2 InputTerminal details Please read o36~o46

9 10
 Section II Inspection & Standby Circuit Section II Inspection & Standby Circuit

JP1 1-2：0～20mA frequency inverter and motor must not be greater than 50 meters (maximum).
DA1
More function analog JP1 2-3：0～10VDC When it is above 4kHz, this distance should be reduced. The cable for this
output 1 o15 Set analog output analog connection had better be laid in metal conduit.
functions
※ If the frequency inverter is equipped with peripheral devices (such as filter,
JP2 1-2：0～20mA
reactor), first measure its insulation resistance to the earth with 1000V megohm
More function analog JP2 2-3：0～10VDC
DA2
o16 Set analog output analog
meter, and ensure the resistance value is not below 4MΩ.
output 2
functions ※ If the frequency inverter must be started frequently, don’t switch off its power
o19/o20 set the output signal arrange supply, and the operator must start or stop the inverter by using the COM/FWD
2-5-2 Control circuit terminal of the control terminal or Keyboard or RS485, in order to avoid damage to the
2-5-1-1 8KLCB Control circuit terminal bridge rectifier.
※ Don’t connect A.C. input power to the output terminals U, V, W of the
frequency inverter.
※ In order to prevent unexpected accidents, earthing terminal E or must be
grounded to the earth securely (the grounding resistance should be below 100Ω).
The cable size should be greater than half of below- mentioned corresponding
cable size; otherwise current leakage will happen possibly.
2-5-1-2 8KSCB Control circuit terminal ※ For wiring of main circuit, please refer to national rule.
※ Capacity of the motor should be equal to or smaller than that of the inverter.
※ Specification of MCCB、electric cable and contractor
In/out Cable Rated Operational
(Copper Current Of Contractor
Type MCCB(A)
Core) A
mm2 (voltage:380V or 220V)
PI8100 R40G2 10A 1.5 10
PI8100 R75G2 16A 2.5 10
2-6. Connection Precautions PI8100 1R5G2 20A 2.5 16
※ Don’t install power factor capacitance or resistance-capacitance absorbing PI8100 2R2G2 32A 4 20
device between the output terminals U, V, W of the frequency inverter. PI8100 004G2 40A 6 25
※ Do not drop Metal scrap foam or lint into the frequency inverter, otherwise the PI8100 5R5G2 63A 6 32
machine will be faulted. PI8000 7R5G2 100A 10 63
PI8000 011G2 125A 10 95
※ To disassemble or replace the motor, the input power supply must be turned off
PI8000 015G2 160A 25 120
for the frequency inverter.
PI8000 018G2 160A 25 120
※ The motor or power supply can be switched on/off only after the inverter stops PI8000 022G2 200A 25 170
its output. PI8000 030G2 200A 35 170
※ In order to minimize the effect of electromagnetic interference, a surge PI8000 037G2 250A 35 170
absorbing device should be installed if used electromagnetic contactor and relay, PI8000 045G2 250A 70 230
etc. is near to the frequency inverter. PI8000 055G2 315A 70 280
※ For external control of frequency inverter, a isolation device should be used for PI8000 R75G3 10A 1.5 10
the control lines or screened cable should be used. PI8000 1R5G3 16A 1.5 10
PI8000 2R2G3 16A 2.5 10
※ A screened cable should be used as the signal connection line for input PI8000 004G3 25A 2.5 16
command and must be routed separately as well, and it had better be installed
PI8000 5R5G3 25A 4 16
far from the main circuit.
PI8000 7R5G3 40A 4 25
※ When the carrier frequency is less than 3kHz, the distance between the PI8000 011G3 63A 6 32

11 12
 Section II Inspection & Standby Circuit Section III Operating Keyboard

PI8000 015G3 63A 6 50 Section III. Operating Keyboard

PI8000 018G3 100A 10 63
PI8000 022G3 100A 10 80
PI8000 030G3 125A 16 95 3-1. Operating keyboard
PI8000 037G3 160A 25 120 3-1-1 JPxC8000 Specification and function description
PI8000 045G3 200A 35 135 Reverse Lndication Light
Monitor Select 1 Numerical Display Alarm Indication Data Unit Prompt Light

PI8000 055G3 250A 35 170 * display the corresponding values

of the function under query
* ON： reverse indication
* OFF：not reverse indication
Light
* ON： faulty
* composed of three indication
lights ，located on the right side of the
LED digital tube ， Display status
* FLASH： reverse accelerating
PI8000 075G3 315A 70 230 status
* display fault code under fault
* OFF：good
* FLASH： previous
corresponding to the six units ， indicate
the unit of the parameters displayed by
condition Forward Indication Light fault was not LED。
PI8000 093G3 400A 70 280 * display the object set byA00 * ON： forward indication confirmed * the correspondence is as following ：

monitor select while running * OFF：not forward indication

PI8000 110G3 400A 95 315 * FLASH： forward accelerating
%
Hz
UNIT

%
Hz
UNIT

%
Hz
UNIT

%
Hz
UNIT

PI8000 132G3 400A 95 380 Positive And Negative Sign Indication

DIGITAL PANEL S
A °C
S
A °C
S
A °C
S
A °C

Light
PI8000 160G3 630A 150 450 V V V V
* just for monitor select FWD REV ALARM NO UNITS Hz A V

UNIT UNIT UNIT

PI8000 187G3 630A 185 500 Monitor Select 3 Numerical Display + Hz

% %
Hz

%
Hz

%
Hz

ON

A00 Monitor Select 1 A ℃ A °C A °C A °C

PI8000 200G3 630A 240 580 - V

s S

V
S

V
S

V
OFF

Monitor Select 2 Numerical Display

PI8000 220G3 800A 150*2 630 % S °C

-
A01 Monitor Select 2 S00 Set Fre.

EN TE
PI8000 250G3 800A 150*2 700 0.00 0.5
ENTER

R
A03 Monitor Select 3 1 Actual Fre.
2 Motor AC * have the same function with PRG/ ，

+
PI8000 280G3 1000A 185*2 780 Parameter Setting/Shift Key
refer to explaination of key PRG/
* Invalid in the monitoring state
PI8000 315G3 1200A 240*2 900 * start to change parameter
* Functions value adjustments
PRG MF1 MF2 FWD Potentiometer Key
PI8000 355G3 1280A 240*2 960 Modification bit
* under checking state, the
function items value has
Multi-function Key MF1/MF2
PI8000 400G3 1380A 185*3 1035 * MF1 define functions through SET
been in increment or
ESC STOP/RESET decrement
parameter A43
PI8000 500G3 1720A 185*3 1290 * MF2 define functions through
* under revising state, the
edit bit of function items
parameter A44 value has been in increment
* A43/A44=0 MF defined as plus function or decrement
* A43/A44=1 MF defined as minus function * under monitoring, setting
* A43/A44=2 MF defined as free stop frequency to increase or
function
decrease
2-7. Standby circuit * A43/A44=3
function
MF defined as forward
Acceleration Select/Parameter
When the fault or trip of the inverter may cause great loss or accident, please add * A43/A44=4 MF defined as reverse
function
Setting Key
* press SET key and rotate Forward running key
the standby circuit. * A43/A44=5 MF defined as Punctuality
dynamic function
JOG key while selecting
parameter, the parameter
* drive forward running
* A43/A44=6 MF defined as Anti-Jog location changes to 10
Note: confirm and test the running characteristic of the standby circuit, in order function * finish and save the value
Quit Key
* exit the revisement of parameter
Reset /Stop Key
* A43/A44=7 MF defined as Jog function changes * drive stop running
to ensure the industrial phase and the converter phase are in the same direction. * A43/A44=8 MF defined as Up function * change the object under
* reture to displaying menu from
submenu or functional menu * Exception Reset
* A43/A44=9 MF defined as Down function monitor * fault confirmation

Interlock relay

13 14
 Section III Operating Keyboard Section III Operating Keyboard

3-1-2 JPxE8000 Keyboard Specification and function description 3-2 Example for Parameters set
3-2-1 F01 keyboard set the frequency from 50.00Hz to 25.00Hz。
Monitor Select 1 Numerical Display Reverse Indication Light Alarm Indication Data Unit Prompt Light
* display the corresponding values * ON： reverse indication Light *composed of three indication
lights ，located on the right side of the PRG
* OFF：not reverse indication * ON： faulty
of the function under query
status * FLASH： reverse accelerating * OFF：good
LED digital tube ，Display status
corresponding to the six units ， indicate
1. Under monitoring status,press into parameter group to query status;
* display fault code under fault * FLASH： previous
condition Forward Indication Light fault was not
the unit of the parameters displayed by
LED。 2. Through potentiometerSwitch to F00-63 Basic FG;
*the correspondence is as following ：
* display the object set byA00 * ON： forward indication confirmed PRG
monitor select while running * OFF：not forward indication
* FLASH： forward accelerating Hz
UNIT
Hz
UNIT
Hz
UNIT
Hz
UNIT
3. Press ,or ENTER,enter into F00-63 Basic FG parameter group to query status;
% % % %

Positive And Negative Sign

DIGITAL PANEL S
A °C
S
A °C
S
A °C
S
A °C
4. Through potentiometerSwitch to F01Fre. Set by K;
Indication Light V V V V PRG
* just for monitor select FWD REV ALARM NO UNITS

UNIT
Hz

UNIT
A

UNIT
V
5. Press ,or ENTER,enter into F01 Fre. Set by K parameter modify status;
Hz Hz Hz
+ Hz PRG
A
%

s
℃
%

S
A °C
%

S
A °C
%

S
A °C
ON
6. Through ,or ENTER,adjust the value is modified bit;
OFF
-
Monitor Select 2 Numerical Display
V
V

%
V
S
V
°C 7. Through potentiometerHas been modified to adjust the bit values;

-
SET
ESC
8. Finish the adjustment,press ;if cancle the change ,press to escape to the

EN TE
ENTER

R
* have the same function with PRG/ ，
modify status;

+
refer to explaination of key PRG/
Parameter Setting/Shift Key * Invalid in the monitoring state
* start to change parameter
* Functions value adjustments
9. Press ESC to exit to previous menu .
Modification bit
PRG MF1 MF2 FWD Potentiometer Key
* under checking state, the
function items value has
Multi-function Key MF1/MF2
been in increment or
* MF1 define functions through SET ESC STOP/RESET decrement PRG PRG
parameter A43 * under revising state, the
* MF2 define functions through edit bit of function items
parameter A44 value has been in increment
* A43/A44=0
* A43/A44=1
MF defined as plus function
MF defined as minus function
or decrement S00 Set Fre. One F00-63 Basic FG Or F00 Control Mode
* under monitoring, setting
* A43/A44=2 MF defined as free stop frequency to increase or 0.00 0.0 Times PI8000 G00 0.00 0.0
function
decrease ENTER
* A43/A44=3 MF defined as forward 1 Actual Fre. 1 Actual Fre. One
1 Actual Fre.
function Acceleration Select/Parameter
* A43/A44=4 MF defined as reverse Setting Key 2 Motor AC 2 Motor AC Times 2 Motor AC
function * press SET key and rotate Forward running key
* A43/A44=5 MF defined as Punctuality JOG key while selecting * drive forward running
dynamic function parameter, the parameter Functional
* A43/A44=6 MF defined as Anti-Jog location changes to 10 Potentiometer
function * finish and save the value
Quit Key
Reset /Stop Key
adjustment
* exit the revisement of parameter
* A43/A44=7 MF defined as Jog function changes
* reture to displaying menu from
* drive stop running item
* A43/A44=8 MF defined as Up function * change the object under * Exception Reset
* A43/A44=9 MF defined as Down function submenu or functional menu
monitor * fault confirmation
PRG PRG

F01Fre. Set By K Or F01Fre. Set By K Or F01Fre. Set By K

0.00 0.0 ENTER 0.00 0.0 ENTER 0.00 0.0
1 Actual Fre. Adjust 1 Actual Fre. One
1 Actual Fre.
2 Motor AC the 2 Motor AC Times 2 Motor AC
resivement
to adjust the
Potentiometer
value of
resivement

SET

F01Fre. Set By K One F01Fre. Set By K

0.00 Times 0.00
0.0 0.0
1 Actual Fre. 1 Actual Fre.
2 Motor AC 2 Motor AC

15 16
 Section III Operating Keyboard Section III Operating Keyboard

3-2-2 Parameter upload to the keyboard 3-2-3 Reset system parameters

Parameter Item Description Parameter Item Description
N function 0 N function 0
System parameter upload to the 1 memory area1 in the keyboard to reset system
1
memory area1 in the keyboard parameter
System parameter upload to the 2 memory area2 in the keyboard to reset system
2
y01 parameter memory area2 in the keyboard y00 Reset system parameter
upload to the System parameter upload to the 3 parameters memory area3 in the keyboard to reset system
3
keyboard memory area3 in the keyboard parameter
System parameter upload to the 4 memory area4 in the keyboard 1to reset system
4
memory area4 in the keyboard parameter
Clear memory area in the 5 Use the factory setting reset system parameter 5
keyboard1,2,3,4 e.g.1：memory area3 in the keyboard 1 to reset system parameter
e.g. System parameter upload to the memory area3 in the keyboard 1. Under monitoring status,press
PRG
into parameter group to query status
PRG
1. Under monitoring status,press into parameter group to check status; 2. Through potentiometerSwitch to y00-23 System FG;
2. Through potentiometerSwitch to y00-23 System FG; PRG

PRG
3. Press ,or ENTER,enter into y00-23 System FG parameter group to query
3. Press ,or ENTER,enter into y00-23 System FG parameter group to check status;
status; 4. Through potentiometerSwitch to y01P Upload To K;
4. Through potentiometerSwitch to y01P Upload To K; PRG

PRG
5. Press ,or ENTER,enter into y00 Reset SP parameter modify status;
5. 5. Press ,or ENTER,enter into y01P Upload To K parameter modify status; 7. Through potentiometer adjust to 3 ;
7. Through potentiometer adjust value to be 3 ; SET

SET
8. Finish the adjustment,press ;the speed for download will display on the LED;if
8. Finish the adjustment,press ;the speed for upload will display on the LED;if ESC
cancle the change ,press ;
cancle the change ,press ESC to escape to the modification status; ESC
9. Press to exit to previous menu。
ESC
9. Press to exit to previous menu。
PRG
PRG Potentiometer

Potentiometer S00 Set Fre. One F00-63 Basic FG y00-23 System FG

S00 Set Fre. F00-63 Basic FG y00-23 System FG 0.00 0.0 Times PI8000 G00 PI8000 G09
One
0.00 PI8000 G00 PI8000 G09 1 Actual Fre. 1 Actual Fre. 1 Actual Fre.
0.0 Times
1 Actual Fre. 1 Actual Fre. 1 Actual Fre. 2 Motor AC 2 Motor AC 2 Motor AC
2 Motor AC 2 Motor AC 2 Motor AC
PRG One
One Times
PRG
Times
PRG

PRG Potentiometer

Potentiometer y00 Reset SP Or y00 Reset SP y00 Reset SP

y01P Upload To K y01P Upload To K y01P Upload To K 0.00 0.0 ENTER 0.00 0.0 0.00 0.0
Or
0.00 0.0 0.00 0.0 0.00 0.0 1 Actual Fre. 1 Actual Fre. 1 Actual Fre.
ENTER 2 Motor AC 2 Motor AC 2 Motor AC
1 Actual Fre. 1 Actual Fre. 1 Actual Fre.
2 Motor AC 2 Motor AC 2 Motor AC to adjust the
Potentiometer value of
Potentiometer
to adjust the resivement
value of
resivement
SET

SET
y00 Reset SP One P Donload K Download y00 Reset SP
0.00 Times finished 0.00
y01P Upload To K One y01P Upload To K Upload y01P Upload To K 0.0 USE MEMORY 3RD 0.0
0.00 Times Finished 0.00 1 Actual Fre. 100%-END 1 Actual Fre.
0.0 USE MEMORY 3RD 0.0
1 Actual Fre. 1 Actual Fre. 2 Motor AC STOP-END 2 Motor AC
100%-END
2 Motor AC STOP-END 2 Motor AC

17 18
 Section III Operating Keyboard Section III Operating Keyboard

3-2-4 F02 the main set mode of set frequency is set to 4, keyboard
e.g.2 Clear memory area in the keyboard1,2,3,4 potentiometer setting !
PRG
1. Under monitoring status,press into parameter group to check status 1. Under monitoring status,Through potentiometer adjust the frequency ,the
2. Through potentiometerSwitch to y00-23 System FG; resolution ratio potentiometer is 0.05Hz。
PRG
3. Press ,or ENTER,enter into y00-23 System FG parameter group to check 2. Range of set frequency can be set with the following parameters：
status; Parameter item Description
4. Through potentiometerSwitch to y01P Upload To K; Inverter output maximum frequency allowed
PRG F12 max. frequency
5. Press ,or ENTER,enter into y01P Upload To K parameter modify status; Setting range：10.00~320.00Hz
A45 keyboard potentiometer Keyboard potentiometer setting the start value
7. Through potentiometer adjust to 5 ; setting X1 Setting range：0~100％
SET
8. Finish the adjustment,press ;the speed for Clear memory area will display on A46 keyboard potentiometer Keyboard potentiometer setting the end value
ESC setting X2 Setting range：0~100％
the LED;if cancle the change ,press ;
ESC
Display the value of potentiometer setting,range：
9. Press to exit to previous menu。 A47 keyboard potentiometer
A45~A46
setting value
Also can set diretly,Setting range：A45~A46
PRG
Potentiometer
Keyboard potentiometer setting the starting point
A48 keyboard potentiometer
S00 Set Fre.
One
F00-63 Basic FG y00-23 System FG for the corresponding value
0.00 0.0 PI8000 G00 PI8000 G09 setting X1correspond to Y1
1 Actual Fre.
Times
1 Actual Fre. 1 Actual Fre.
Setting range：-100％~+100％
2 Motor AC 2 Motor AC 2 Motor AC Keyboard potentiometer settings corresponding to
A49 keyboard potentiometer
PRG One the value of the end
Times setting X2 correspond to Y2
Setting range：-100％~+100％
PRG Displays the current size of the set frequency,
Potentiometer
S00 setting frequency through the potentiometer setting
y01P Upload To K Or y01P Upload To K y00 Reset SP
0.00 0.0 ENTER 0.00 0.0 0.00 0.0 Setting range：F12×A48~ F12×A49
1 Actual Fre. 1 Actual Fre. 1 Actual Fre.
2 Motor AC 2 Motor AC 2 Motor AC

to adjust the
e.g.：
Potentiometer
value of
resivement
F12=50.00Hz,A45=0%,A46=100%,A47 Shows the value of potentiometer settings
SET
0％~100％,Numerical size can be adjusted by potentiometer。
（1） when A48=0%,A49=+100%,S00 Set Fre.range 0.00Hz～50.00Hz。
y01P Upload To K One
Times
y01P Upload To K Clearance
Finished
y01P Upload To K （2） when A48=0%,A49=+50%,S00 Set Fre.range 0.00Hz～25.00Hz。
0.00 0.0 0.00 0.0 0.00 0.0
1 Actual Fre. 1 Actual Fre. 1 Actual Fre. （3） when A48=-100%,A49=+100%,S00 Set Fre.range -50.00Hz～50.00Hz。
2 Motor AC 2 Motor AC 2 Motor AC
Note：when the motor is in -50.00~0Hz realise reverse ,another setting
F45Ten bit motor forward inverse as
1 Command priority: Analog given positive and negative values,on the F45 details
refer to F45 Parameter Description

19 20
 Section III Operating Keyboard Section IV Test Running

Section IV. Test Running

3-2-5 F02 the main set mode of set frequency is set to 1,AI1 external analog
given.
1. Under monitoring status,Through external analog input terminal Al1 adjust the ● Failure occurred when test running , please anomalies and Countermeasures
frequency ,the resolution ratio is 0.01Hz。 against 6-1 fault diagnosis, processing, trouble shooting.
2. Set the frequency range can be set with the following parameters： ● Inverter parameters have a strong adaptive ability, in general b11 = 1 calculation
Parameter Item Description of electrical parameters with the name plate, on this basis, a little manual
Inverter speed adjustment’s allowed maximum output adjustment can get you high-performance vector control.
F12 most frequency
frequency Setting range：10.00~320.00Hz ● Only when the motor completely without the load can set b11 = 3 motor rotation
Keyboard potentiometer setting the start value measurements
o00 AI1 input X1
Setting range：0~100％ ● Before the electrical parameter measurement finished , inverter can have the
Keyboard potentiometer setting the end value ourput voltage any time, please ensure the safety.
o01 AI1 input X2
Setting range：0~100％
Keyboard potentiometer setting the starting point for
o06 AI1 input X1
the corresponding value Setting
correspond to Y1
range：-100％~+100％
Keyboard potentiometer settings corresponding to the
o07 AI1 input X2
value of the end
correspond to Y2
Setting range：-100％~+100％
Display the frequency ,Through out analog input
S00 frequency setting terminal Al1 adjust the frequency
Setting range：F12×o06~ F12×o07

Example：
F12=50.00Hz,o00=0%,o01=100%,
（1） When o06=0%,o07=+100%,S00 Set Fre.range 0.00Hz～50.00Hz 之间。
（2） When o06=0%,o07=+50%,S00 Set Fre.range 0.00Hz～25.00Hz。
（3） When o06=-100%,o07=+100%,S00 Set Fre.range -50.00Hz～50.00Hz。
Note：When the motor is in -50.00~0Hz realise reverse ,another setting
F45Ten bit motor forward reverse as
1 Command priority: Analog given positive and negative values,on the F45 details
see F45 Parameter Description

21 22
 Section IV Test Running Section IV Test Running

test
running
sensor
V/F vector
Control control
power voltage inverter in the sensorless
rated input voltage range vector
According to parameter control
setting F06 V / F boost adjust speed loopC01-C07、
power supply connect to RST of inverter, confirm mode Turned around differential gain、
the correct grounded then supply power regulate motor parameters
adjust speed loopC01-C07、
Set F07 torque Turned around differential
boost value Upper torque
gain C09-C12、regulate
Confirmed the inverter power matches to the setting C13、C14
motor parameters
motor power ,reset the factory value of y00 =5 setting F01
running frequency upper torque Set PG pulses C28，PG
setting directions C30
Select motor parameters, motor parameters set in accordance parameters parameters
running optimization
with motor nameplate set of parameters, rated power, rated optimization running running
current, rated voltage, the number of pole pairs, motor speed
observe running current Observe the motor current, Observe motor
and motor state excitation component, torque speed S06
fluctuation component
Set the appropriate acceleration and deceleration time, the motor parameters
N N Normal
maximum frequency F12, the fundamental frequency F15 Normal N optimization
Normal operation
operation
operation Y
Y Observe the motor current,
Set the keyboard for a Y
Stop and test excitation component, torque
given frequency of F01 running finish Stop and test fluctuation component
running finish
Normal N
Press the keyboard keys operation
are transferred to run FWD Y
Shut down power outages, swap Stop and test
any two-phase motor line running finish

forward running N
direction of the motor

Y
Shut down after the motor
parameter tuning

b11=1 b11=2 b11=3

Calculated using plate Static frequency converter Measurement
measurement converter operation

Press FWD self-tuning start

(motor may be running safety)

N Set the appropriate F09/F10 acceleration

The success of self-tuning and deceleration parameters, F06/F07
torque control parameter
Y
Choose
F00Control mode

sensorless Sensor
V/F
vector vector
Control
control control

23 24
 Section V Parameter Function Table Section V Parameter Function Table

Section V Parameter function table motor b03/b16＝2,the real speed of the motor ＝1500rpm。
When stop,based Residual voltage test motor speed,renew speed 500ms。
The real speed ＝60×residual frequency×Gain Speed surveillance / the pole of the motor
5-1 Menu Group Max display of motor real speed 9999rpm.
Group S07 Total Running Time The total running time for every time hour - N
Code Description / LCD Function Discription Quantity
ID When the ouptput ,the frequency inverter calculated the running time.
Monitor Function Monitor frequency,current and other 16 Total running time can be cleared up automatically with A33 selecting reboot or continue
S 16 0B
Group monitor objects accumulation after reboot
Basic Function Frequency setting,control mode, Total running time of the units can be changed by parameter A34, you can choose hours or days as the
F 51 00 unit
Group accelerationtime and deceleration time
IGBT Test the temperature of IGBT in the
User Function S08 ℃ - N
A Monitor,protection,communication setting 56 01 Temperature ℃ frequency
Group PID Adjust run-time values of the
S09 PID Set Point % - N
o IO Function Group Analog,digital input,output function 61 02 percentage of a given
PID Adjust run-time values of the
S10 PID Feedback % - N
Multi-speed PLC percentage of feed back
H Multi-speed running,PLCrunning 56 03
Group Motor Output The percentage of actual output
S11 % - N
Frequency power of motor
U V/F Curve Group User defined V/Fcurve 16 04
The output frequency of the motor ＝the actual frequency of the motor ×A36the regulate of the motor
frequency
PID Function
P Internal PID parameter setting 13 05 Max display of the output frequency 2999.9
Group
Excitation Heft Set Motor’s set excitation heft
S12 % - N
Extend Gunction Constant pressure water supply and other Value percentage
E 24 06 Excitation Heft Motor’s actual excitation heft
Froup functions setting S13 % - N
Actual Value percentage
Speed ring function S14 Torque Heft Set Value Motor set torque percentage % - N
C Current ring,speed running,PGparameter 32 07
group Torque Heft Actual
Motor parameter S15 Motor actual torque hefts percentage % - N
b Motor parameter setting 23 08 Value
group
System Function Parameter reset,fault query ,product 5-3 Basic function Group
y 18 09 Upper group Next group
Group information,parameter protection
Description/LCD
Setting Range Factory Change
Code Keyboard Unit
5-2 Monitor function 7 Step LED Display Setting Limited
Display
Next group
Description/LCD Setting Range Factory Change V/Fcontrol 0
Code Unit
Keyboard Display 7 Step LED Display Setting Limited
F00 Control Mode Sensorless vector control 1 - 0 N
current inverter real setting Sensor feedback close loop vector
S00 Setting Frequency Hz - N 2
frequency control
S01 Real Frequency current inverter real output frequency Hz - N Keyboard
S02 Motor real Current Valid value of motor actual current A - N F01 Setting Lower frequency～upper frequency Hz 50.00 Y
S03 Percentage of Motor The percentage of actual motor Frequency
% - N
Current current and rated current Control mode choose,setting 0～2。
S04 DC Bus Voltage Detection value of DC bus voltage V - N 0： V/ Fcontrol
S05 The Output Voltage The real output voltage V - N It is not sensitive to motor parameters, can be used as power supply; for motor control, using the
S06 Motor Real Speed Motor real running speed - - N
combination of vector control and V / F control strategies, appropriately adjusts motor parameters, obtain
Under running ,the real speed of the motor ＝60×the real output frequency ×Gain Speed surveillance high-performance control effect; suitable for a inverter driving a motor occasions; suitable for a inverter
/pole of the motor 。 driving multiple motors occasions; suitable for the inverter as a variable frequency power supplies.
Example：the real output frequency50.00Hz,Gain Speed surveillance A35=100.0％,the pole of the 1：Sensorless vector control

25 26
 Section V Parameter Function Table Section V Parameter Function Table

High-performance speed sensorless vector control; need to set the appropriate electrical parameters or Multi-segment digital voltage setting 5
the motor parameter tuning; truly achieved the decoupled AC motor, so that operational control of DC Digital Pulse Set 6
motors.
PID regulation mode 7
2：Sensor feedback close loop vector control
Auxiliary setting mode of frequency set：
Suitable for high precision speed control of occasions, it is need to install PG card and install pulse
0：keyboard frequency setting frequency or RS485, change F01 kayboard setting frequency
encoder shaft in the motor or mechanical equipment,.
After multi-digital voltage terminal effective switch, change F01keyboard setting。
The keyboard for a given operating frequency, the frequency can be any one between lower frequency 1：AI1 the external analog setting
and upper frequency to the upper frequency Given the external analog 0~10V,－10V～＋10V ,0~20mA. For detail please read the o group
F02/F03setting to 0, Involved in setting frequency calculation. parameter.
Keyboard setting frequency or RS485 0 2：AI2 the external analog setting
3：AI3 the external analog setting
AI1 the external analog setting 1
Given the external analog 0~10V,0~20mA。For detail please read the o group parameter。
Frequency AI2 the external analog setting 2
F02 Main Set AI3 the external analog setting 3 - 0 Y 4：Keyboard potentiometer setting
Mode Keyboard potentiometer setting , keyboard potentiometer for a given start and end values of the
Keyboard potentiometer setting 4
corresponding values can be positive role and negative effects. For detail please read the A group
Multi-segment digital voltage setting 5 parameter。
Digital Pulse Setting 6
The main mode of the frequency running frequency： 5：Multi-segment digital voltage setting
0：keyboard setting frequency or RS485 change F01 keyboard setting frequency o36～o46 IO input terminal function set to 11,12,13,switch H47～H54 Multi-digital voltage
Multi-digital voltage terminal effective exchange, change F01keyboard setting value setting ,100% Corresponding to the maximum frequency .
1：AI1 the external analog setting 6：Digital pulse set
Given the external analog 0~10V,－10V～＋10V ,0~20mA. For detail please read the o group Digital pulse input frequency corresponding to set the frequency, For detail please read o52
parameter。 parameter。
2：AI2 the external analog setting Pulse input terminal and DI8 terminal reseting ,After use digital pulse input,o43set to 0,Otherwise, the
3：AI3 the external analog setting function settings will take effect,can check the pulse input status o58,be limited to low-speed pulse.
Given the external analog 0~10V,0~20mA. For detail please read the o group parameter。 7：PID regulation mode
The completion of the main to the frequency of common analog feedback loop control. Speed control
4：Keyboard potentiometer setting accuracy requirements applicable to the general occasions.
Keyboard potentiometer setting , keyboard potentiometer for a given start and end values of the The given value can be given through the keyboard can also be given through the analog.
corresponding values can be positive role and negative effects. For detail please read the A group Analog feedback can represent the pressure, flow, temperature.
parameter。 Details see the P group of parameters.
The completion of the main to the frequency of common analog feedback loop control. Speed control
5：Multi-segment digital voltage setting accuracy requirements applicable to the general occasions.
o36～o46 IO input terminal function set to 11,12,13,switch H47～H54 Multi-digital voltage For a given value can be given through the keyboard can also be given through the analog.
setting ,100% Corresponding to the maximum frequency . Analog feedback can represent the pressure, flow, temperature.
6： Digital pulse setting Details see the P group of parameters.
Digital pulse input frequency Corresponding to the setting frequency,For detail please read the o52 Through o36~o46 IO input terminal, set to 17,18,19 be configured to switch the source for a given
group parameter。 ratio。
Pulse input terminal and DI8 terminal reset,after using the digital pulse input ,o43set to
0,Otherwise, the function settings will take effect, the pulse input on status of o58 can be checked,be The main setting individual control 0
The
limited to low-speed pulse. The auxiliary setting individual control 1
Relationship
Through o36~o46 IO input teminal set to 14,15,16 be configured to switch the source
Between main + auxiliary 2
Keyboard setting frequency or RS485 0
F04 Main And main -auxiliary 3 - 0 Y
Auxiliary AI1 the external analog setting 1 Auxiliary
Setting Mode （main *auxiliary）/maximum
F03 AI2 the external analog setting 2 - 0 Y Setting 4
Of frequency
Frequency
Frequency AI3 the external analog setting 3 Maximum｛main ,auxiliary｝ 5
Keyboard potentiometer setting 4

27 28
 Section V Parameter Function Table Section V Parameter Function Table

Minimum｛main ,auxiliary｝ 6 Stop and running command control mode

Main given and auxiliary given set frequency relations: 0：keyboard ＋RS485/CAN Control
Main given value and auxiliary given value can be added up, subtracted, multiplied, maximum, 1：keyboard＋Terminal＋RS485/CAN Control
minimum calculation. control terminal, edge trigger, falling edge of the implementation of the Forward command FWD /
O group parameters can be adjusted to coordinate the main given and auxiliary given proportion, to Reverse command REV, rising edge of the implementation of the STOP command
meet the requirements of the system fine-tuning and bias。 2：RS485/CAN Control
Under this function,only free stop funciont is valid under the keyboard control, other operation
f
control is invalid
f setting frequency 3：Terminal control,Level trigger。
fmax
Under this function,only free stop funciont is valid under the keyboard control, other operation
f auxiliary control is invalid
4：The proportion linkage control
fmain fsetting frequency f main Select this function, the slave unit would execute the command from the proportion linkage host unit.
F04
Select this function, can also use keyboard, terminal, RS485 to control the proportion linkage slave
unit to run.
fauxiliary The proportion of linkage running, after stop the proportion linkage slave unit with the keyboard
The relationship between main t terminal, RS485, the slave unit will not run the proportion liknge host unit’s command, it needs once again
give and auxiliary given Main+Auxiliary to respond to host commands through the keyboard, terminal, RS485, or the proportion linkage host sends
stop command so that slave unit could respond to run commands.
f f Beeline V/Fcurve 0
Power of 1.2 V/Fcurve 1
f max f max f main
Power of 1.7 power
2
fauxiliary Bit V/Fcurve
Power of 2
V/F Boost 3
f main f auxiliary powerV/Fcurve
Mode - 0000 N
Define mode V/Fcurve 4
F06
fsetting frequency Close Automatic torque
0
10 boost
t
f setting frequency t
Automatic torqueboost 1
Main-Auxiliary (Main*Auxiliary)/The Max Frequency
100 Reserved
f f

fmax fmax 1000 Reserved

f setting frequency f setting frequency 1 Bit：V/F promote curve

fauxiliary fauxiliary
0 Line V/F curve：Suitable for ordinary constant torque load
f main f main 1 Power of 1.2 V/F curve：Appropriate torque down V/F curve,Suitable for liquid loads
2 Power of 1.7 V/F curve：Appropriate torque down V/F curve,Suitable for liquid loads
3 Power of 2 V/F curve：Torque down V/F curve,It is suitable for fans, pumps, centrifugal load
4 Define mode V/Fcurve：Can be customized appropriate curve according to the actual situation .
t t Ten：Auto-torque boost mode
Maximum（Main & Auxiliary） Minimum（Main & Auxiliary） 0 Close Automatic torque boost
1 Open automatic torque boost
Keyboard +RS485/CAN 0 Torque boost
F07 0.0～30.0% % 0.0 Y
Running Keyboard +terminal+RS485/CAN 1 Value
F05 Control RS485/CAN 2 - 0 Y Torque Boost
Mode F08 Cut-off 0.00～Maximum frequency Hz 15.00 Y
Terminal control 3
Frequency
The proportion linkage control 4 Torque increase is mainly used to improve the low-frequency torque characteristics under

29 30
 Section V Parameter Function Table Section V Parameter Function Table

sensorless-V / F control mode.

Torque boost is too low, weak low speed motor
maximum frequency
Torque boost is too high, motor over-excitation operation, large inverter output current, and low
efficiency. upper limit frequency
Set the torque converter to enhance the frequency below the cutoff frequency, torque to enhance
effective, more than this to set the frequency, torque increase is invalid. lower limit frequency

voltage voltage 0 100％ frequency set signal

motor rated motor rated
voltage voltage
F13 Lower frequency: the lower limit of the output frequency.
F14 Upper frequency: the uppper limit of output frequency.
When the frequency setting command is higher than the upper frequency, the operating frequency will be
Frequency Frequency the upper frequency; When the frequency setting command below the lower frequency, the operating
Enhance Enhance
voltage Cut-off frequency Basic frequency voltage Cut-off frequency Basic frequency
frequency is lower frequency. Start the motor that in the status of stopping, the inverter outputs accelerate
down the torque curve torque boost Constant torque curve torque boost
starting from 0Hz, accordance with the step 1 acceleration time towards the upper or the setting frequency
to accelerate. when motor Stop, the operating frequency decelerate according to deceleration time down to
F09 Accelerate Time 0.0～3200.0 s 10.0 Y 0Hz.
Basic
F10 Decelerate Time 0.0～3200.0 s 10.0 Y F15 5.00～Maximum frequency Hz 50.00 N
Frequency
F09 Accelerate time：accelerate time from 0Hz to maximum frequency Corresponding to different fundamental frequency of the motor select this function. The basic V / F
F10 Decelerate time：decelerate time from maximum frequency to 0Hz。 characteristic curve is as below.

output frequency
Vout
Fmax
Un

running time
F09 F10
base maximum Fout
Linear Acceleration frequency frequency
Percentage Of Carrier kH
F11 50～110 % 100 Y F16 1.0～16.0 ★ Y
Output Voltage Frequency z
The percentage of the actual output voltage and the rated output voltage。 This function is chiefly used to improve the possible noise and vibration during the operation of
Used to adjust the output voltage,output voltage ＝inverter rated output voltage×percentage of output frequency converter. When carrier frequency is higher, the output current has better wave, the torque is
voltage great at lower frequency and the motor produces light noise. So it is very suitable for use in the applications
Maximum where great torque is output at low frequency quietly. But in these applications, the damage to the switches
F12 10.00～320.00 Hz 50.00 N
Frequency of main components and the heat generated by the inverter are great, the efficiency is decreased and the
Inverter output maximum frequency allowed is also the setting basis of acceleration / deceleration output capacity is reduced. At the same time, more serious radio interference is resulted and special
time attention must be paid for application where very low EMI is needed, and filter option can be used if
This parameter setting, you should consider characteristics of the motor speed and capacity necessary. Another problem for application of high carrier frequency is the increase of capacitance-leakage
Lower current. The protector for leakage current may invalidate function, and over current is also possibly caused.
F13 0.00～Upper frequency Hz 0.00 N When low carrier frequency is applied, the case is almost contrary to the above-mentioned one.
Frequency
Different motor has different reflection to the carrier frequency. The best carrier frequency is gained
F14 Upper Frequency Lower frequency～Upper frequency Hz 50.00 N after regulation according to actual conditions. The higher the motor capacity is, the lower the carrier
frequency should be selected.

The company reserves the right to limit maximum carrier frequency as following:

31 32
 Section V Parameter Function Table Section V Parameter Function Table

The relation between carrier frequency and Motor Noise , Electric disturbance , Switch dissipation is 1：Stepless & subsection synchronous space vector PWM
expressed as following: 2：two-phase optimization space vector PWM
F20 S Curve Start Time At The Acceleration Step 0.0～50.0 % 0.0 Y
Carrier
Motor Noise Electric disturbance Switch dissipation F21 S Curve Stop Time At The Acceleration Atep 0.0～50.0 % 0.0 Y
Frequency
F22 S Curve Start Time At The Deceleration Step 0.0～50.0 % 0.0 Y
1.0KHz
Big Small Small F23 S Curve Stop Time At The Deceleration Step 0.0～50.0 % 0.0 Y
8.0KHz ↕ ↕ ↕
Small Big Big
16.0KHz setting frequency 1

The relationship of the carrier frequency and power ：

Power(kW) 0.4-18.5 22-30 37-55 75-110 132-200 220 以上 F20 F21 F22 F23
setting frequency 2
Carrier 1 2 3 1 2 3
Frequency 8.0K 7.0K 4.0K 3.6K 3.0K 2.5K running time
F09 F10
(Hz)
S curve acceleration/deceleration
Note：Carrier frequency is bigger,the temperatuer of the machine is higher。
1 indicat that the slope of the output frequency from 0 to the max.
Carrier
2 indicat that the slope of the output frequency at constant segment.
Frequency kH
F17 0.0～4.0 0.0 Y 3 indicat that the slope of the output frequency is reduced to 0 from the max.
Adjustment z
Such as setting the S curve acceleration and deceleration, acceleration and deceleration time from 0Hz
Range
to the maximum frequency is calculated as follows:
N automatic adjustment 0 Plus acceleration S characteristic time = F09 × F20
Carrier Bit
Frequency automatic adjustment Mode 1 Constant extra acceleration S characteristic time = F09-(F09 × F20 + F09 × F21)
F18 - 00 Y Minus acceleration S characteristic time = F09 × F21
Adjustment automatic adjustment,Fixed mode 0
Mode Ten Full acceleration time = F09 Acceleration time
automatic adjustment,random mode 1 Velocity S addition and subtraction characteristic time = F10 × F22
F17 Carrier frequency adjustment range Constant deceleration S characteristics time = F10-(F10 × F22 + F10 × F23)
0.0～4.0kHz,Actual Carrier frequency adjustment range 1.0～16.0kHz And reduction rate of S characteristic time = F10 × F23
All deceleration time = F10 deceleration time
F18 Carrier frequency adjustment Mode
Bit： Carrier frequency automatic adjustment mode V/F Control Slip slip compensation invalid 0
F24 - 0 N
0：N automatic adjustment Compensation slip compensation valid 1
Carrier frequency according F16 to set 。 0: Slip compensation function is invalid.
1：automatic adjustment Mode 1: Run in the V / F control method, the slip compensation function effectively.
The carrier frequency automatically adjusts the model 10 can select random mode and fixed pattern. Slip compensation value to adjust the following parameters to ensure stable speed under load
Ten： Stochastic adjustment mode fluctuations and heavy load,.
0：automatic adjustment,Fixed mode C09 Low Slip Gain
C10 Low Slip switching frequency
Load current>80% Carrier frequency =F16-F17
C11 High-Speed Slip Gain
Load current<60% Carrier frequency =F16+F17
Slip C12 high-speed switching frequency
1：automatic adjustment,random mode
Minimum Running
Load current >80% Carrier frequency = (F16-F17)～F16 F25 0.00～maximum frequency Hz 0.00 N
Frequency
Load current <60% Carrier frequency = F16～(F16+F17)
The set frequency lower than the minimum running frequency, the converter will stop, that is, when the
Asynchronous space-vector PWM 0
Waveform set frequency is less than the minimum running frequency, are determined that the set frequency is 0.
Stepless & subsection synchronous space
F19 Generation 1 - 1 N "Minimum running frequency" and "lower frequency" relationship is as follows.
vector PWM
Mode
two-phase optimization space vector PWM 2
PWM wave produce mode
0：Asynchronous space-vector PWM

33 34
 Section V Parameter Function Table Section V Parameter Function Table

set frequency set frequency

lower limit Minimum setting
frequency frequency frequency

Minimum lower limit

frequency frequency time
Time Time output
frequency stop brake wait time
actual frequency actual frequency
Minimum braking
lower limit
frequency frequency
frequency
lower limit stop braking time time
Minimum
frequency frequency RUN
ON OFF
Time Time
STOP
Minimum frequency<lower frequency Minimum frequency>lower frequency stop braking (RUN→STOP)

DC Braking
setting
F26 Current When 0～135 % 100 Y frequency
Starting
Braking Time
F27 0.0～60.0 s 0.0 Y
When Starting time
output
When frequency Inverter starting, the first injection of DC current, the current size is determined by frequency stop braking time
starting to set when the DC braking current and braking time, braking time from the start to set.
braking
Value is based on inverter rated current as the benchmark, that is inverter rated current corresponds to frequency
100%. During setting process, be sure to gradually increase , until adequate braking torque, and can not time
stop brake wait time setting
exceed the motor rated current. frequency
forward
output reverse FOR REV
frequency command
stop braking (forward and reverse rotate)
start up braking

time
RUN setting
ON
STOP frequency
start up braking braking
frequency
time
Stop When The DC output
F28 0～135 % 100 Y frequency stop brake wait time
Braking Current
Stop And Braking Wait Y braking
F29 0.0～60.0 s 0.0 frequency
Time
stop braking time time
F30 Brake Time Stop 0.0～60.0 s 0.0 Y
RUN
Stop And Brake Starting ON
STOP
F31 0.00～most frequency Hz 0.00 Y
Frequency stop braking (run state)
Inverter slowing down to stop braking start frequency, stop the output PWM waveform to begin
injection of DC current, the current size by the shutdown of DC braking current setting, braking time, Deceleration stop 0
braking time set by the downtime. F32 Stop Setting Mode - 0 N
Free stop 1
Value is based on inverter rated current as the benchmark, that is inverter rated current corresponds to
When the frequency inverter receives the "stop" command, it will set the parameters accordingly to
100%. Setting process, be sure to gradually increase from a small, until adequate braking torque, and can
this parameter to set the motor stop mode.
not exceed the motor rated current.
0: deceleration to stop, mode converter according to parameters set by the deceleration time to set the
deceleration mode to slow down to the lowest frequencies to stop.
1: Free stop mode, inverter receive "stop" command immediately stop output, according to the load
inertia, motor free-run to stop.
F33 Jog 0.0～3200.0 s 1.0 N

35 36
 Section V Parameter Function Table Section V Parameter Function Table

Acceleration F42 Skip Frequency 3 Upper 0.00～Maximum frequency Hz 0.00 Y

Time
During running, to skip resonance produced by the immanent resonance point in the machine systems,
Jog
F34 Deceleration 0.0～3200.0 s 1.0 N skip mode can do this.
Time At most three resonance points could be set to skip.
Jog direction：forward 0 output frequency
Jog direction：reverse 1 upper skip frequency 1
Bit Jog direction：direction skip frequency 1
lower skip frequency 1
determined by the main 2
upper skip frequency 2
terminal skip frequency 2
lower skip frequency 2
Jog end mode: Stop Running 0
upper skip frequency 3
Tens Jog end mode:reset to the skip frequency 3
Jog Mode 1 lower skip frequency 3
F35 former state before jog - 000 N
Setting
Jog end and acceleration
deceleration time: reset to the
0 frequency setting signal
set acceleration and
Upper skip frequency and lower skip frequency define skip frequency range.
deceleration time before jog
hundred In the acceleration and deceleration process, inverter output frequency can normally through skip
Jog end and acceleration
deceleration time:save the set frequency area.
1
acceleration and deceleration
time before jog
F43 Preset Frequency 0.00～Max frequency Hz 0.00 Y
Jog Frequency
F36 Lower frequency ～upper frequency Hz 6.00 Y F44 Preset Frequency Working Time 0.0~60.0 S 0.0 Y
Setting
Jog acceleration and deceleration time to configure the definition of the same section of acceleration / After inverter startup, it firstly run with preset frequency , running time is preset frequency time, then
deceleration time. it will run with given frequency. Jog run will not be effective by preset frequency.
Jog the direction of movement of bits determined by the F35, when moving the command does not Direction command：forward
contain Jog fixed direction, the direction will be moving inch F35-digit specified direction. This bit is set to command FWD let motor 0
2 inch of movement from the terminal or the current direction of the direction of the decision. forward running
Bit
Jog running after the end of the 10 identified by the F35. Direction command：forward
Jog acceleration and deceleration time can be determined through the F35's hundred jog at the end had command FWD let motor reverse 1
been maintained. Motor running
F45 Running Command prior： - 0100 N
Direction 0
output frequency terminal/keyboard
X10
Prior command：Analog given
Fmax 1
positive and negative values
Reverse allow: reverse forbidden 0
X100
Reverse allow: can reverse 1
Bit: used to change the direction of motor running
running time
F33 F34 0：Forward command FWD is to let motor forward running.
Linear Acceleration 1：Forward command FWD is to let motor reverse running.
X10 bit：Motor forward reverse running can be controled by the keyboard potentiometer and analog
F37 Skip Frequency 1 Limit 0.00～Maximum frequency Hz 0.00 Y input input positive or negative value.
F38 Skip Frequency 1 Upper 0.00～Maximum frequency Hz 0.00 Y 0：Prior command：terminal/keyboard,set frequency can be negative value,but running direction
decided by terminal and keyboard command.
F39 Skip Frequency 2 Limit 0.00～Maximum frequency Hz 0.00 Y
1：Prior command：positive or negative value of analog input,setting frequency positive value let motor
F40 Skip Frequency 2 Upper 0.00～Maximum frequency Hz 0.00 Y forward running, seting negative value let motor reverse running。
F41 Skip Frequency 3 Limit 0.00～Maximum frequency Hz 0.00 Y X100 bit：motor reverse allow. For some producing equipment, the reverse may lead to damage to the
equipment,so this feature can be used to prevent motor reverse,Inverter default forbidden reverse. When the

37 38
 Section V Parameter Function Table Section V Parameter Function Table

motor running direction opposes to equipment required direction, you can exchange the wiring of any two Adjustment of Multi steps
5
inverter output terminals to let equipment forward running direction is consistent with motor running. digital voltage giving
0：reverse forbidden Acceleration time：×S 0
1：reverse allow Acceleration time：×min 1
100
F46 Pass 0 Stopping Time 0.0~60.0S S 0 N Acceleration time：×h 2
Setting this parameter to achieve the motor forward to reverse (or from reverse running to forward), Acceleration time：×day 3
the waiting time of motor speed being zero Deceleration time：×S 0
Deceleration time：×min 1
1000
Deceleration time：×h 2
output
frequency F47 Deceleration time：×day 3

bit：Acceleration time ajustment mode

N Adjustment Of
running time 0 Acceleration Time N adjustment

AI1 Adjustment Of The

1 Actual Acc. time=Acc. time*AI1 giving percentage
External Analog Giving

×1 0 Actual Acc. time = Acc. time *AI2 giving percentage

AI2 Adjustment Of The
F47 Frequency Multiple Setting - 0 N 2
×10 1 External Analog Giving
0：Set frequency display accurat 0.01Hz,With this accuracy,F12 Maximum frequency setting range Actual Acc. time = Acc. time *AI3 giving percentage
AI3 Adjustment Of The
10.00～320.00Hz。 3
External Analog Giving
1：Set frequency display accurat 0.1Hz,with this accuracy,F12 Maximum frequency setting range
100.0～800.0Hz。 Actual Acc.time = Acc. time * keyboard potentiometer
giving percentage
After setting this parameter,there must be reset F12 maximun frequency. Adjustment Of Keyboard
4
Potentiometer Giving
N adjustment of acceleration
0
time Actual Acc.time = Acc. time * Multi steps digital voltage
AI1 adjustment of the external Adjustment Of Multi giving percentage
1 5 Stepes Digital Voltage
analog giving
AI2 adjustment of the external Giving
2
analog giving
bit
AI3 adjustment of the external
3 X10 bit：Deceleration time ajustment mode
analog giving
Adjustment of keyboard
Acceleration 4 N Adjustment Of
potentiometer giving 0 N adjustment
And Acceleration Time
Adjustment of Multi steps
F48 Deceleration 5 - 0000 N
digital voltage giving
Configuration AI1 Adjustment Of The
N adjustment of decceleration 1 Actual Acc.time =Dec. time*AI1 giving percentage
Word 0 External Analog Giving
time
AI1 adjustment of the external Actual Acc.time = Dec. time *AI2 giving percentage
1 AI2 Adjustment Of The
analog giving 2
External Analog Giving
AI2 adjustment of the external
10 2 Actual Acc.time = Dec. time *AI3 giving percentage
analog giving AI3 Adjustment Of The
3
AI3 adjustment of the external External Analog Giving
3
analog giving
Adjustment of keyboard
4
potentiometer giving

39 40
 Section V Parameter Function Table Section V Parameter Function Table

Actual Acc.time = Dec. time * keyboard potentiometer ×Day 3 3200.0 Day

giving percentage
Adjustment Of Keyboard
4
Potentiometer Giving
F50 Energy Saving Running Percentage 30～100 ％ 100 N
Actual Acc.time = Dec. time * Multi stepes digital voltage This parameter describes the minimum output voltage of the percentage of energy-saving operation. In
giving percentage the constant speed operation, the inverter can be automatically calculated the best output voltage by the
Adjustment Of Multi
5 load conditions.In the process of acceleration and deceleration is not to make such calculations.
Steps Digital Voltage
Power-saving function is by lowering the output voltage and improve power factor to achieve the
purpose of saving energy, this parameter determines the minimum value of reducing of output voltage;This
X100,X1000 bit：The unit of Acc. and Dec time when program running on 0 step speed parameter is set to 100%, then energy-saving function will take off.
Acc. and Dec. X1000 Range（e.g. F09,F10=3200.0） When energy-saving function in effect,Actual output voltage value of inverter= The inverter rated
time X100 bit output voltage×The percentage of output voltage×output voltage percentage of energy saving operation.
×S 0 3200.0 S
output voltatge (V)
×Min 1 3200.0 Min 100%
×H 2 3200.0 h
75%
×Day 3 3200.0 Day
Running direction：
0 frequency (Hz)
forward
bit
Running direction：
Running 1
reverse
F49 Configuration Running time：×S 0 - 0000 N
Word 5-4 User Function Group
Running time：×Min 1 Upper group Next group
10
Running time：×H 2 Spec/LCD
Setting Range Default Change
Running time：×Day 3 Code Keyboard Unit
7 Steps LED Display Setting Limits
Display
Unit adjustment of actual running time。It is only valid on program running.
A00 Monitor 1 Parameter group N: Parameter group N: - 0B00 Y
bit：Program running on multi-speed running period,Set bit to running direction of “0”step speed. A01 Monitor 2 - 0B01 Y
X1000/X100 X10/ bit
A02 Monitor 3 00~0B 0~63(0x00~0x3F) - 0B02 Y
Running driection Setting value
Parameter Function Parameter N(16 Hexadecimal
Code Keyboard display
Forward 0 group N spec Input)
Reverse 1 S Monitor Function Group 0B S 0~16 (0x00~0x10)
F Basic Function Group 00 F 0~60 (0x00~0x3C)
When running control mode F05＝0/1/2,control direction of “0” step speed.
A User Function Group 01 A 0~56 (0x00~0x38)
When running control mode F05＝3,Setting the value and terminal FWD / REV run jointly decide the 02
o IO Function Group o 0~61 (0x00~0x3D)
direction of 0 step speed, FWD priority。 Multi-step Speed PLC
H 03 H 0~56 (0x00~0x38)
FWD=1running REV=1running Group
Setting value
direction direction U V/F Curve Group 04 U 0~16 (0x00~0x10)
P PID Function Group 05 P 0~13 (0x00~0x0D)
FWD REV 0
E Extend Function Group 06 E 0~14 (0x00~0x0E)
REW FWD 1
Speed Loop Parameter
10：unit of time running on “0” step speed. C 07 C 0~32 (0x00~0x20)
Group
Running time X10 bit Range（e.g. H18~H25=3200.0） b Motor Parameter Group 08 b 0~23 (0x00~0x17)
×S 0 3200.0S y System Function Group 09 y 0~18 (0x00~0x12)
×Min 1 3200.0Min
That parameter N. should be 16 hex input。
×H 2 3200.0H
Monitor1 will be valid when first power on, and which decide keyboard display content.

41 42
 Section V Parameter Function Table Section V Parameter Function Table

Such as:monitor 1 S01 actual frequency,A00=0x0B01。 predetermined value, the dynamic braking will be implemented
Monitor 2 o57 DI1~4 terminal status,A01=0x0239。 2：general Type, under any state, when the inverter detected high-voltage DC bus exceeds a
Monitor 3 H55 multi-steps speed status, A02=0x0337。 predetermined value, the dynamic braking will be implemented.
Over /Less Voltage Stall N 0 When the inverter is running on emergency deceleration state or load great fluctuation, it may appear
A03 - 1 Y over-voltage or over-current. This phenomenon is relatively prone to happen when the motor load inertia is
Protection Y 1
heavy.When inverterThe inverter internal DC bus detected voltage exceeds a certain value, the output brake
Overvoltage Stall
A04 110%~140%( Standard bus voltage) % 120 Y signal through an external braking resistor implement energy-braking function. Users can select inverter
Protection Voltage
0：This function invalid models with a braking function to apply this feature。
1：This function valid A09 Less Voltage Level 60%~75%(Standard DC bus voltage) % 70 Y
When the inverter deceleration, as the motor load inertia,motor will produce feedback voltage to The definition of allowed the lower limit voltage of normal working inverter DC side .For some low
inverter inside, which will increase DC bus voltage and surpass max voltage. When you choose Over /less power occasions, inverter less voltage value can be appropriately put down in order to ensure the inverter
voltage stall protection and it is valid,Inverter detects DC side voltage, if the voltage is too high, the normal working.。
inverter to stop deceleration (the output frequency remains unchanged), until the DC side voltage is below Under normal condition, keeping default setting。
the set value, the inverter will re-implement the deceleration
N 0
With braking models and external braking resistor ,this function should be set to “0”。
Power-off
A10 Power-down Tracking Options 1 - 0 Y
tracking mode
Startup tracking
DC voltage 2
mode
A11 Power-down tTracking Time 0.0~20.0 S 0.0 Y
This parameter is used to select the inverter tracking mode。
time
0：N speed tracking means to start tracking from 0 Hz.
output frequency 1：power-down tracking,When the inverter instantaneous power off and re-start,the motor will continue
running with current speed and direction.
If the power off time is longer than A11 set time, the inverter will not re-start power on again.
time 2：Startup tracking means that when power on, inverter will first inspect motor direction and speed,
and then driving motor with current speed and direction.
Invalid 0 Set startup tracking function, power off tracking function is still valid.

A05 Auto Stablize Voltage Valid 1 - 0 Y input power down power frequency
control
Valid,usless for power
2
deceleration frequency conversion
CPU automatically detect the inverter DC bus voltage and to make real-time optimized processing,
when the grid voltage fluctuate, the output voltage fluctuation is very small, the V / F curve characteristic motor
motor
speed search
rotate
has always been close to setting state of rated input voltage.。 rotate
speed
speed
0：function inalid.
1：function Valid.
2：function Valid,but useless for deceleration. output output
frequency frequency
Invalid 0
A06 Dynamic Braking option Security Type 1 - 0 Y
General Type 2 power down track state start track state

A07 Hysteresis voltage 0～10％ ％ 2 Y

65~100%(standard DC
Dynamic Braking A12 Power Down Frequency Drop Point % 75 Y
A08 110%~140%( Standard bus voltage) % 130 Y bus voltage)
Voltage
A13 Power Down Frequency Drop Time 0.1～3200.0 s 5.0 Y
0：Invalid
1：Security Type,Only in the inverter deceleration process, and detected high-voltage DC bus exceeds a Correctly setting this parameter can let inverter does not less voltage stop in case of instantaneous

43 44
 Section V Parameter Function Table Section V Parameter Function Table

power off. condition.

When the DC bus voltage drop to frequency drop point A12 set, inverter will decelerate according to N torque inspection 0
deceleration time A13 set and stop outputting power to load. Meanwhile, inverter will use load feedback
Over Torque Warning and running 1
energy to compensate DC bus voltage dropping and keep inverter working in short time. A20 - 0 Y
Inspected Action Warning and decelerating stop 2
Power down frequency drop time actually is deceleration time of frequency dropping after power off.
If this value set is too large, the load feedback energy is small, then inverter can not compensate for Warning and free stopping 3
voltage dropping in DC。 A21 Over Torque Grade 10~250 ％ 150 Y
if this value set is too small and there is large energy feedback from load, the excessive energy Over Torque
compensation may cause inverter over-voltage fault。 A22 0.0~60.0 s 0.1 Y
Inspection Time
Set A12 100% to cancel power off frequency dropping function. Motor output current surpass value A21 set,Over torque inspection will be force and the system will
show OL2 fault.
N 0
A14 Current Limit - 1 Y N 0
Y 1 A23 Electronic Thermal Relay Protection Selection - 1 Y
Y 1
A15 Limit Fall Time 0.1～3200.0 s 3.0 Y
This function is to protect motor overheating when motor does not use thermal relay. Inverter using
A16 Limit Deceleration Protection Point 10~250 ％ ★ Y some parameters to calculate motor temperature rise, at the same time to determine whether the use of
A17 Limit Fix-speed Protection Point 10~250 ％ ★ Y current caused motor overheat. When you choose electronic thermal protection function, the drive output is
shutdown after overheating detected also shows information of protection.
Series Current limitaiton% Corresponding parameter 0：N selecting this function
120 A17 1：Select this function。
F
130 A16
150 A17
G A24 Electronic Thermal Protection Grade 120～250 % ★ Y
170 A16
170 A17 This is current grade set by inverter analyzing motor overheat result. When current reach multiple of
M、T、Z
190 A16 motor rated current and this parameter. Inverter will protect motor within one minute.The actual overheat
250 A17
H protection current is A24 times of rated current within that one minute.
270 A16
This parameter default setting of F series is 120%, G/S series is150%,Z/M/T sries is 180%,H series is
Current limitation function can effectively restrain over-current caused by motor load fluctuation in 250%.
the process of acceleration and deceleration or constant speed operation.
protect time
This function will be good effect for V/F control mode.
Under protection of current lost- speed state, the motor speed will drop. so it is not adapted by 20min
systme which is not allowed to automatically drop speed.
In operation process, when the motor current surpass value A16 set, motor will decelerate according to 5min
deceleration time A15 set until current below value A16 set. 1min
In operation process, when the motor surpass value A17 set,motor will run with this speed until 0.2s
current below value A17 set.
F46 ％Ia
Deceleration current limitation is prior of constant speed limitation.
N protection of phase lost 0
A25 Fault Reset Times 0～10 - 0 Y
Output Phase Lose Warning and constant running 1 In the inverter operation process,Over Current expressed by OC、Over Voltage by OU,inverter can
A18 - 0 Y
Protection Warning and deceleration 2 automatically recover and run with state of preceding fault. Recovering times will be according to this
Warning and free stopping 3 parameter. It can set 10 times at most. When this parameter is set “0”, inverter will not automatically
Grade Of Phase Lose recover after meeting fault. But if relay in DC main circuit meet fault “MCC” or less votage “LU” fault,
A19 10~100 ％ 30 Y
Protection inverter will automatically recover without limitation.
When ratio of unbalance 3phase output surpass A19 Grade of phase lose protection, the inverter Restarting from fault and normally running over 36s, inverter will automatically recover fault reset
output phase lose protection i will action, and the system display fault PH-O. times preset.
Output frequency less than 2.00Hz, there is N output phase lose protection. Restarting from fault and normally running over 36s,inverter will automatically recover to display
Phase lost protection grade=max current difference between phases,which will be according to load monitor parameter.

45 46
 Section V Parameter Function Table Section V Parameter Function Table

After 10 s of meeting fault, inverter will not recover fault reset function. N warning for
0
communication fault
A26 Fault Reset Time 0.5～20.0 s 1.0 Y Communications Warning and running 1
A31 - 0 Y
Setting interval of fault reset time. When inverter met fault and stopped outputting, and when it Troubleshooting Warning and decelerating
2
inspected without fault time is longer than fault reset time, Inverter will automatically implement fault stop
reset. Warning and free stopping 3
A27 Fan Startup Temperature 0.0～60.0 ℃ 0.0 Y 0：N inspection
A32 Delay Inspection Time s 10 Y
This parameter used to set temperature of fan startup. When actual temperature is higher thanset 1~250：late inpsection
temperature, fan will startup. When communication time between interface A or B surpassed A32 delayt inspection time,the system
A28 This Inverter Communication Address 1～128 - 8 Y will warn according to A31 setting.
This Inverter communication address：it is the only code to differentiate from other inverters. After power on,interface without communication will not implement warning.
Setting range “1~127” is slave inverter address, that can receive command and send out this inverter Auto clear to zero after power
0
state. Seeing attachment 1 for detailed specification. Total Running Time on
A33 - 1 Y
Setting Continue to accumulate
The proportion of linkage function： 1
running time after power on
The proportion of linkage host inverter：
The set for whether accumulating time of inverer running.
This inverter communcaiton address=128,
0：Auto clear to zero after power on.
Communication interface A is set as host inverter communication interface for proportion of linkage.
1：Continue to accumulate running time after power on.
Communication interface B can be treated as keyboard interface or “PC” Host Computer Interface.
The proportion of linkage slave inverter： Unit Of Total hour 0
A34 - 0 Y
This inverter communication address =1～127, Running Time Day 1
Communication interface A and B both can be set as communication interface of slave inverter for the The set for unit of accumulation running time, only for display of running time.
proportion of linkage. 0：unit /hour display range 0~3200.0 hour.
Seeing appendix 2 for detailed specification. 1：unit/day display range 0~3200.0 day.
A35 Motor Output Speed Adjustment 0.1～1000.0 % 100.0 Y
Baud rate is Using for displaying adjustment of motor actual running speed. Seeing A00~A02 monitor options：6:
0
1200 motor actual running speed.
Baud rate is Setting 100%,corresponding display unit : rpm.
1
2400 The max speed of displaying after adjustment is 9999.
Baud rate is
2 A36 Adjustment Of Motor Output Power 0.1～1000.0 ％ 100.0 Y
4800
A29 Baud Rate - 3 Y Used for displaying motor ouput power of adjustment. Seeing A00~A02 monitor options：11 :motor
Baud rate is
3 output power.
9600
Setting 100%,corresponding display unit:％。
Baud rate is
4 The max ouput power of displaying after adjustment is 2999.9.
19200
A37 Keyboard Lock Function Options 0~0FF - 0FF Y
Baud rate is
5
38400
7 6 5 4 3 2 1 0
The baud rate of communication interface A can be set accordingly. 2 2 2 2 2 2 2 2
The baud rate of communication interface B is fixed 19200bps。 7 6 5 4 3 2 1 0
8,N,1 for RTU 0 FWD
8,N,2 for RTU 1 STOP
PRG
8,E,1 for RTU 2
A30 Communication Format - 0 Y SET
8,O,1 for RTU 3 ESC
4 MF1
8,E,2 for RTU
MF2
8,O,2 for RTU 5 Potentiometer
Seeing attachment for detailed specification。 key SET+ESC in Keyboard can activate and cancel keyboard lock function.

47 48
 Section V Parameter Function Table Section V Parameter Function Table

To lock which key will be decided by corresponding parameter : 1：UP/DN valid adjustment
Set 0~10 bit Keyboard locked state UP fix speed 0
bit
0 Unlock FWD key UP fix times 1
0
1 Lock FWD key DN fix speed 0
10
0 Unlock STOP key DN fix times 1
1
1 Lock STOP key UP N adjustmentof speed ratio 0
0 Unlock PRG key AI1 adjustment of the external
2 1
1 Lock PRG key analog giving.
AI2 adjustment of the external
0 unlock SET key 2
3 analog giving.
1 Lock SET key 100 AI3 adjustment of the external
3
0 Unlock ESC key analog giving.
4 adjustment of Potentiometer
1 Lock ESC key UP/DN 4
A39 giving - 0000 N
Time
0 Unlock MF1 key Adjustment of multi-steps digital
5 5
1 Lock MF1 key voltage
0 Unlock MF2 key DN N adjustmentof speed ratio 0
6 AI1 adjustment of the external
1 Lock MF2 key 1
analog giving
0 Unlock potentiometer AI2 adjustment of the external
7 2
1 Lock potentiometer analog giving
1000
AI3 adjustment of the external
3
analog giving.
0 adjustment of Potentiometer
Power down to save 4
bit giving
Power down to clear saving 1 Adjustment of multi-steps digital
5
saving after stopping 0 voltage
X10 bit Stop command to clear saving 1
UP/DN Cleared at the end of stopping 2
A38 - 0000 Y
Control
One-direction adjustment 0
X100 bit Double-direction
1
adjustment
X1000 Invalide adjustment 0
bit Valide ajustment 1
bit：UP/DN control saving state after power down
0：power down to save
1：power down to clear
X10 bit：UP/DN control saving after stopping
0：Keeping afer stopping
1：Stop command to clear saving
2：Cleared at the end of stopping
X100 bit：UP/DN control direction of adjustment.
0：one direction adjustment,it is one direction adjustment within 0～max frequency range.
1：double direction adjusment,it is FEW and REW adjustment within 0～max frequency range.
X1000 bit：UP/DN control validity of adjustment.
0：UP/DN invalid ajustment

49 50
 Section V Parameter Function Table Section V Parameter Function Table

bit：UP acceleration mode A40 UP/DN Adjustment Value -300.00～300.00 - 0.00 N

0：fix speed acceleration, according to A41 fix speed: To increase frequency every 200ms.
Frequency after adjustment＝set frequency＋UP/DN adjustment value.
1：fix times acceleration, according to fix times：To increase frequency every triggering.
10：DN deceleration mode A41 UP Adjustment Ratio 0.01〜20.00 Hz 0.01 Y
0：fix speed deceleration,according to A42 fix speed：To reduce frequency every 200ms. Fix speed：To increase frequency every 200ms.
1：fix times deceleration, according to A42 fix times: To reduce frequency every triggering. Fix times：To increase frequency every triggering.
100：UP adjustment mode of adjusting speed ratio A42 DN Adjustment Ratio 0.01〜20.00 Hz 0.01 Y
Fix speed：To reduce frequency every 200ms.
Fix times：To reduce frequency every triggering.
UP N Adjustment Of MF is defined as adding
0 N adjustment 0
Speed Ratio function key
MF is definded as reducing
AI1 Adjustment Of The Actual UP adjustment ratio= percentage given by 1
1 function key
External Analog Giving A41*AI1 MFis defined as free stopping
2
key
AI2 Adjustment Of The
2 Actua UP adjustment ratio= percentage given by A41*AI2 MFis defined as FWD running
External Analog Giving 3
key
MF is defined as REV running
AI3 Adjustment Of The Actual UP adjustment ratio= percentage given by The Definition Of 4
3 A43 key 0
External Analog Giving A41*AI3 Multifunction Keys - Y
A44 MF is defined as forward JOG 1
MF1 And MF2 5
Adjustment Of Actual UP adjustment ratio= percentage given by A41* function key.
4 MF is defined as reverse JOG
Potentiometer Giving potentiometer
6
function key.
Adjustment Of MF is defined as JOG function
Actual UP adjustment ratio=percentage given by A41* 7
5 Multi-steps Digital key.
multi-steps digital voltage
Voltage MFis defined as UP function
8
key
MF is defined as Down function
9
key.
X1000 bit：DN adjustment mode of adjusting speed ratio The user defined keyboard can define MF key functions.
0: MF is defined as adding function key：
N Adjustment Of Under monitor menu, adding function key MF can adding revise frequency F01 set.
0 N adjustment
Acceleration Time Under parameter choosing menu, adding function key MF can adjust parameter choice.
Under parameter revising menu, adding function key MF can adjust parameter value.
AI1 Adjustment Of The Actual DN adjustment ratio =percentage given by
1 1: MF is defined as reducing function key：
External Analog Giving A42*AI1
Under monitor menu, reducing function key MFcan reducing revise frequency F01 set
AI2 Adjustment Of The Actual DN adjustment ratio =percentage given by Under parameter choosing menu,reducing function key MF can adjust parameter choice.
2 Under parameter revising menu, reducing function key MF can adjust parameter value.
External Analog Giving A42*AI2
2: MF is defined as free stopping key:
AI3 Adjustment Of The Actual DN adjustment ratio=percentage given by Pressing MF key is valid under monitor menu and parameter choosing menu, inverter will be free
3
External Analog Giving A42*AI3. stopping.
3: MF is defined as FWD running key：
Adjustment Of Actual DN adjustment ratio=percentage given by
4 Pressing MF key is valid under monitor menu and parameter choosing menu,inverter will be forward
Potentiometer Giving A42*potentiometer
running.
4: MF is defined as REV running key:
Adjustment Of
Actual DN adjustment ratio=percentage given by Pressing MF key is valid under monitor menu and parameter choosing menu,inverter will be reverse
5 Multi-steps Digital
A42*multi-steps digital voltge. running.
Voltage
5: MF is defined as forward JOG function key：

51 52
 Section V Parameter Function Table Section V Parameter Function Table

Pressing MF key is valid under monitor menu and parameter choosing menu,inverter will be forward
100 Reserved
JOG running.
6: MF is defined as reverse JOG function key：
Pressing MF key is valid under monitor menu and parameter choosing menu,inverter will be reverse 1000 Reserved
JOG running. bit：Saving state of potentiometer after power down.
7: MF is defined as JOG function key： 0：Saving after power down.
Pressing MF key is valid under monitor menu and parameter choosing menu,inverter will be JOG 1：Clearing saving after power down.
running. Running direction decided by F35 bit setting and terminal state. X10 bit：keeping potentiometer set after stopping.
0：keeping after stopping
8: MF is defined as UP function key：
1：To clear saving after stop command.
Pressing MF is always valid, inverter will be UP control , control parameter decided by A38～A42.
2：To cear saving at end of stopping.
9: MF is defined as Down function key：
Pressing MF is always valid, inverter will be DOWN control , control parameter decided by A38～A42.
A51 Temperature Adjustment Of Motor 0.0～200.0 ％ 100.0 N
A45 Keyboard Potentiometer X1 0~100.0 % 0.0 Y
Being used to revise displaying of A54 motor temperature.
The start point of value keyboard potentiometer set.
A52 Over-heat Temperature Of Motor 0.0～300.0 ℃ 120.0 N
A46 Keyboard PotentiometerX2 0~100.0 % 100.0 Y
N reaction for
The end point of value keyboard potentiometer set. 0
motor over-heat
The Value Of Keyboard Potentiometer Warning and runing 1
A47 0.0~100.0% % - Y
Set Warning and
Displaying value potentiometer set,which can be revised by potentiometer under monitor menu. A53 Reaction For Motor Over-heat - 0 Y
deceleration 2
Value potentiometer set can be regarded as analog of frequency giving, set value=max stopping
frequency×keyboard potentiometer set value Warning and free
Potentionmeter set value can be regarded as value of PID giving, value of PID giving=keybaord 3
stopping
potentiometer set value.
When the displaying value of motor temperature A5 surpassed value A52 , inverter will warn and react
Keyboard Potentiometer X1 according to reaction for motor over-heat A53 set.
A48 -100.0~100.0 % 0.0 Y
Corresponding Value Y1
A54 Display Of Motor Temperature －50.0～300.0 ℃ - N
Keyboard Potentiometer X2
A49 -100.0~100.0 % 100.0 Y The motor temperature value measured by optional accessory PT100 can be used for temperature
Corresponding Value Y2
measurement of other parts.
A55 Proportion Of Linkage Ratio 0.10～10.00 - 1.00 Y

End point End point

In application of proportion of linkage,A55 setting is multiply ratio of that when slave inverter received
corresponding corresponding setting frequency command from host inverter.
value value
Setting this inverter as one slave inverter of system for proportion of linkage.
Frequency Keyboard F01 set＝proportion of linkage ratio× frequency S00 set by host inverter
Start point Start point
corresponding corresponding
value value 5-5 IO function group
start point end point start point end point
Upper group next group
Limit
ation
Saving after power down 0 Description/LCD Setting range Default
bit code unit of
Cleared after power down 1 Keyboard display 7 stepsLED display setting
revise
Keyboad
Saving after stoppoing 0 ment
A50 Potentiometer - 0000 Y
Control Clear saving after stopping o00 AI1 Input X1 0~100.0 % 0.0 Y
10 1
command %
o01 AI1 Input X2 0~100.0 100.0 Y
Clear saving at end of stopping 2
o02 AI2 Input X1 0~100.0 % 0.0 Y
o03 AI2 Input X2 0~100.0 % 100.0 Y

53 54
 Section V Parameter Function Table Section V Parameter Function Table

o04 AI3 Input X1 0~100.0 % 0.0 Y y

o05 AI3 Input X2 0~100.0 % 100.0 Y 100%

AI1 Input X1 Corresponding 80%
o06 -100.0~100.0 % 0.0 Y
Value Y1 10V
(X2,Y2)
AI1 Input X2 Corresponding Y2=50%
o07 -100.0~100.0 % 100.0 Y
Value Y2
AI2 Input X1 Corresponding Y1=20% (X1,Y1)
o08 -100.0~100.0 % 0.0 Y
Value Y1
AI2 Input X2 Corresponding AI1,AI2,AI3
o09 -100.0~100.0 % 100.0 Y X1=0% X2=50% 100% x
Value Y2
AI3 Input X1 Corresponding
o10 -100.0~100.0 % 0.0 Y
Value Y1
X1=0% ,Y1＝-100% potentiometer 0V corresponding set frequency：f=Max
AI3 Input X2 Corresponding
o11 -100.0~100.0 % 100.0 Y frequency×Y1=-50.00Hz
Value Y2
X2=100% ,Y2＝100% potentiometer 5V corresponding set frequency：f=Max
Under the situation Max frequency＝50.00hz： frequency×Y2=50.00Hz
X1=0% ,Y1＝0% potentiometer 0V corresponding set frequency：f=Max
frequency×Y1=0.00Hz
y
X2=100%,Y2＝100% potentiometer 10V corresponding set frequency：f=Max
frequency×Y2=50.00Hz 100% (X2,Y2)
y Y2=100%

Y2=100%

X2=100%
AI1,AI2,AI3
50% 100% x
5V 10V

Y1=0% (X1,Y1)
AI1,AI2,AI3 x X1=0%
X1=0% X2=100%
Y1=-100% (X1,Y1)
X1=20% ,Y1＝0% potentiometer 2V corresponding set frequency：f=Max
frequency×Y1=0.00Hz Skipping thread of AI1,AI2,AI3 respectively are JP3/JP5,JP6,JP7, seeing the following detailed
X2=50% ,Y2＝50% potentiometer 5V corresponding set frequency：f=Max specification：
frequency×Y2=25.00Hz
y

100%

(X2,Y2)
Y2=50%

o12 AI1 Input Filter Time 0.00～2.00 s 0.10 Y

Y1=0% (X1,Y1)
AI1,AI2,AI3 o13 AI2 Input Filter Time 0.00～2.00 s 0.10 Y
X1=20% 80% 100% x
10V o14 AI3 Input Filter Time 0.00～2.00 s 0.10 Y
X2=50%
X1=0% ,Y1＝20% potentiometer 0V corresponding set value：f=Max Filter time constant of analog signal input,that is 0.00～2.00s。If time parameter is set too long, the
frequency×Y1=10.00Hz changement of setting frequency will be stable, but responsing speed will be slow;If time parameter is set
X2=50% ,Y2＝50% potentiometer 5V corresponding set value：f=Max frequency×Y2=25.00Hz
too short, the changement of setting frequency will not be stable, but responsing speed will be quick.

o15 DA1 Output Terminal N reaction 0 - - Y

o16 DA2 Output Terminal Setting frequency 1 - - Y

55 56
 Section V Parameter Function Table Section V Parameter Function Table

Actual frequency 2
the corresponded
Actual current 3 output frequency

Output voltage 4 DA2

DC bus voltge 5 DA1

IGBT temperature 6
0Hz
Output power 7
10.0% 20.0% 50.0% 100.0% Voltage/Current
Output RPM 8 0V/0mA 10V/20mA

Actual value of torque 9 Such as：

If DA1 output 1～5V voltage,setting parameter as：o17＝10.0%,o18＝50.0%
DA1 Adjustment Of
o17 0.0～100.0 % 0.0 Y If DA2 output 4～20mA current,setting parameter as：o19＝20.0%,o20＝100.0%
Lower Limit Output
DA1 Adjustment Of DA1,DA2 Skipping thread：
o18 0.0～100.0 % 100.0 Y
Upper Limit Of Output
DA2 Adjustment Of
o19 0.0～100.0 % 0.0 Y
Lower Limit Output
DA2 Adjustment Of
o20 0.0～100.0 % 100.0 Y
Upper Limit Output

Caution：Every terminal has choice of voltage output and current output, the default setting is voltage
Setting output. When the voltage output is needed, please connect JP1/JP2 and DA1V/DA2V（seeing the
Output Content Giving Output Singla Range
Value panel）;When the current output is needed,please connect JP1/JP2 and DA1C/DA2C。

N Reaction 0 N output N function 0

Setting Fault warning 1
1 0～Max frequency
Frequency
Over current inspection 2
Actual Over load inspection 3
2 0～Max frequency
Frequency
Over voltage inspection 4
0～200%,corresponding parameter：S03 percentage of Less voltage inspection 5
Actual Current 3
output curent O1 Output Signal
Low load inspection 6
Option1
0～200%,corresponding parameter：b02、b15 rate o21 O2 Output Signal Over heat inspection 7 - 0 Y
Output Voltage 4
voltage of motor o22 Option 2 - 0 Y
Running state with command 8
o23 O3 Output Signal - 1 Y
DC Bus Voltage 5 0～1000VDC, DC voltage
o24 Option 3 Abnormal PID feedback signal 9 - 8 Y
IGBT O4 Output Signal
6 0～100.0℃ Motor state of REW running 10
Temperature Option 4
Arrival of setting the frequency 11
Output Power 7 0～200％
Arrival of Upper frequency 12
Output RPM 8 0～Max RPM
Arrival of Lower frequency 13
Actual Value Of
9 0～200% torque Arrival of FDT setting frequency 1 14
Torque
Arrival of FDT setting frequency 2 15

This parameter is used for setting upper/lower limitation of DA1/DA2 output signal. FDT frequency level inspection 16

57 58
 Section V Parameter Function Table Section V Parameter Function Table

Arrival of preset counter value 17 Motor State Of REW

10 Motor is reverse running
Arrival of upper limit counter 18 Running
Program running one period
19 Arrival Of Setting
completed 11 Arrive at set frequency
Frequency
Speed tricking mode inspecition 20
Arrival Of Upper
N command running state 21 12 Arrive at upper frequency
Frequency
REV running from inverter
22
command Arrival of lower
13 Arrive at lower frequency
Deceleration running 23 frequency

Acceleration running 24
Arrival Of FDT Set
14 Arrive at frequency 1 FDT set
Arrival of high pressure 25 Frequency 1

Arrival of low pressure 26

Arrival Of FDT Set
15 Arrive at frequency 2 FDT set
Arrival of inverter rate current 27 Frequency 2

Arrival of motor rate current 28 Inspection Level Of FDT FDT frequency levels to meet the inspection
16
Arrival of input frequency lower Frequency conditions,o29～o31
29
limitation
Arrival of current upper limitation 30 17 Arrival Of Preset
Present counting value arrives at preset counting value
Counting Value
Arrival of current lower limitation 31
Arrival Of Counting Present counting value arrives at upper limitation of
18
Value Upper Limitation counting value.
Setting
Output Content Specification Explaination
Value
Program Ruuning One
19 Program runs one period to complete.
Setting “0”,N output reaction,but inverter can be Period Completion
0 N Function
controlled by theoretical terminal.
Inspection In Speed
20 Inverter is under speed trick state, the valid time is A11
1 Fault Warning Inverter at fault or after fault with unconfirmed status. Trick Mode

2 Over Current Inspeciton Inverter met fault of over current N Command Running
21 Inverter is under N command running state
State
3 Over Load Inspeciton Inverter met fault of over load of heat protection
REW Command Of
22 Inverter is under reverse running command
Inverter
4 Over Voltage Inspeciton Inverter met fault of over voltage
23 Deceleration Running Inverter is under deceleration running
24 Acceleration Running Inverter is under acceleration running
5 Less Voltage Inspeciton Inverter met fault of less voltge
25 Arrival Of High Pressure Arrival at hight pressure
6 Lower Load Inspection Inverter met fault of lower load 26 Arrival Of Low Pressure Arrival at low pressure
7 Over Heat Inspeciton Inverter met fault of over heat.
Arrival Of Inverter Rate
27 Arrival at inverter rate current
Running State Of Current
8 Inverter is under running state of command
Command
Arrival Of Motor Rate
28 Arrival at motor rate current
Abnormal PID Feedback Current
9 PID feedback signal is abnormal
Signal

59 60
 Section V Parameter Function Table Section V Parameter Function Table

Arrival Of Input output frequency

Present set frequency is less than frequency lower FDT1=35Hz
29 Frequency Lower
limitation FDT2=30Hz
Limitation

Arrival Of Current time

30 Arrive at current of upper limitation
Upper Limitation
FDT frequency
setting 1 arrived OFF ON OFF ON
Arrival Of Current
31 Arrive at current of lower limitation
Lower Limitation time

0~32.000 S 0 FDT frequency

o25 Output Signal Delay 1 level detect OFF ON OFF ON
o26 Output Signal Delay 2 0~32.000 S 0 time
Y
o27 Output Signal Delay 3 0~32.000 S 0 FDT frequency
o28 Output Signal Delay 4 inspection level OFF ON OFF ON
0~32.000 S 0
time
o25～o28 defines o21～o24 output signal reaction delay time,unit is S. ON means signal will react, OFF means signal will not react
Output signal cut off action without delay.
o29 FDT Set Frequency 1 o30～Max frequecy Hz 0.00 Y Arrival Of Current
o32 o33~200% % 120 Y
Upper Limitation
o30 FDT Set Frequency 2 0～o29 Hz 0.00 Y
Arrival Of Current
o33 o34~o32 % 20 Y
o31 FDT Inspection Range 0.00～5.00 Hz 0.00 Y Lower Limitation
Current Inspection
When the choice of output signal（ o21～o24）is set as14,inverter output frequency arrives at or surpass o34 0~o33 % 3 Y
Range
FDT set frequency 1,the corresponding signal output terminal will react; When inverter output frequency
When the choice of output signal（o21～o24）is set as 30 , and inverter output frequency arrived or
is below of frequency 1 FDT set, the corresponding signal output terminal will not react.
surpasseed of “o32+o34”,the corresponding output signal terminal will react. When the inverter output
When the choice of output signal（ o21～o24）is set as15,inverter output frequency arrives at or surpass
frequency is less than o32-o34, The corresponding output signal terminal will not react.
FDT set frequency 3,the corresponding signal output terminal will react;When inverter output frequency
When the choice of output signal（o21～o24）is set as 31,and inverter output frequency arrived or less
is below of frequency 3 FDT set, the corresponding signal output terminal will not react.
than o33-o34, the corresponding output signal terminal will react;When the inverter output frequency is
When the choice of output signal（ o21～o24）is set as16,inverter will firstly inspect FDT set freuqnecy
more than o33+o34,The corresponding output signal terminal will not react.
1,then inverter output frequency arrives at or surpass FDT set frequency 1,the corresponding signal
o34 is used to define current inspection range. When the difference of actual current and inspected current
output terminal will react;After terminal reaction, inverter will inspect FDT set frequency 2,When has surpassed inspection range, The output terminal will react.
inverter output frequency is below of frequency 2 FDT set, the corresponding signal output terminal will
current
not react. percentage
o32=120 120
o33=20
o31 frequency inspection range
o34=3 20
This parameter is used to define inspection range. When the difference of actual frequency and
time
inspected frequency has surpassed inspection range, terminal will output react. current o34 o34 o34 o34
e.g.: FDT set frequency 1 as 35Hz,FDT set frequency 2 as 30Hz, upper
limitation OFF ON OFF ON OFF
Frequency inspection range is 0,the signal output terminal will react as below:
time
current o34 o34
lower
limitation OFF ON OFF

time
ON means signal will react, OFF means signal will not react

Terminal Two-wire running control 1 0

o35 bit - 0x0013 N
Control Mode Two-wire running control 2 1

61 62
 Section V Parameter Function Table Section V Parameter Function Table

Three-wire running control 1 2 Falling edge Low e-level Low e-level FWD running

Falling edge High e-level Low e-level REV running

Three-wire running control 2 3
X X High e-level STOP running
Terminal command is invalid
0
after power on running
X10 bit
Terminal command is valid after
1 3：Three wire running control 2
power on running FWD
FWD
Setting terminal running mode by this parameter. REV
REV
Bit set terminal running mode： STOP
STOP
The polarity of electrical level is o47 default setting polarity. Low electrical level or falling edge is COM

valid, and the terminal is leakage-souce driving mode.

X can be used to express high or low electrical level, rising or falling edge. F05=1 ;F05=3; F05=4
Command
Running Control Mode Keyboard Running Control Prior Running Prior Direction FWD REV STOP
Edge Trigger Valid Same Same Falling edge X Low e-level FWD running
E-level Trigger Invalid Prior running Prior FWD X Falling edge Low e-level REV running

X X High e-level STOP running

0：Two wire running control 1
FWD/ STOP
FWD
10 set the terminal status when the power up
REV/ STOP
REV
Power in an active state when the terminal state, the drive to run immediately, in some cases do not
allow such situation happen.
COM
set the terminal running command invalid when the power up, then power-on and after going through
F05=1 or F05=4 F05=3 the terminal to set an invalid state 3S then running .
Command
FWD REV FWD REV

Falling edge X Low E Level X FWD running N function 0

X Falling edge High E-level Low E-level REV running

(DI1) Input Terminal
Function Selection Forward running FWD 1
Rising edge Rising edge High E-level High E-level STOP running
(DI2) Input Terminal
Reverse running REV 2
Function Selection
1：Two wire running control 2 (DI3 )Input Terminal 3
RUN/ STOP
3-line mode running STOP
FWD
Function Selection
FWD/ REV o36 Multi-segment command 1 4 - 0 Y
REV (DI4) Input Terminal
o37 - 0 Y
Function Selection Multi-segment command 2 5
COM o38 - 0 Y
(DI5) Input Terminal
o39 Multi-segment command 3 6 - 0 Y
Function Selection
F05=1 or F05=4 F05=3
o40 - 0 Y
(DI6) Input Terminal Multi-segment command 7
Command o41 - 0 Y
FWD REV FWD REV Function Selection
o42 Multi-segment speed command 1 8 - 0 Y
Falling edge Falling edge Low e-level Low e-level FWD running (DI7) Input Terminal
o43 - 0 Y
Falling edge Rising edge Low e-level High e-level REV running Function Selection Multi-segment speed command 9
o44 - 0 Y
(DI8) Input Terminal 10
Rising edge X High e-level X STOP running o45 Multi-segment speed command 3 - 0 Y
Function Selection
o46 - 0 Y
(AI1) Input Terminal Multi-segment digital voltage 1 11
2：Three wire running control 1
Function Selection 12
FWD Multi-segment voltage 2
FWD (AI2) Input Terminal
REV
REV Function Selection Multi-segment voltage 3 13
STOP
STOP (AI3) Input Terminal The main set mode 1 of set
COM 14
Function Selection frequency
The main set mode 2 of set
15
F05=1 ;F05=3; F05=4 frequency
Command
FWD REV STOP

63 64
 Section V Parameter Function Table Section V Parameter Function Table

The main set mode 3 of set Counter loading 48

16
frequency
The auxiliary setting mode 1 of Upper counter loading 49
17
frequency set External fault signal input 50
The auxiliary setting mode 2 of 1 pump soft-start 51
18
frequency set
The auxiliary setting mode 3 of 1 pump stop 52
19
frequency set 2 pump soft-start 53
MSS time running 1 20
2 pump stop 54
MSS time running 2 21
3 pump soft-start 55
MSS time running 3 22
3 pump stop 56
Operation control mode shift 1 23
4 pump soft-start 57
Operation control mode shift 2 24
4 pump stop 58
Operation control mode shift 3 25
hand rotate command 59
Forward torque limit shift 1 26
Timing water supply change to 60
Forward torque limit shift 2 27 zero
Forward torque limit shift 3 28
Setting
Output Detail Specification Explaination
Reverse torque limit shift 1 29 Value
0 N- function N- function
Reverse torque limit shift 2 30
Forward command FWD,Can be set to edge triggered
1 Forward command FWD or level-triggered
Reverse torque limit shift 3 31
Reverse command REV,Can be set to edge triggered
Torque speed shift 32 2 Reverse command REV or level-triggered
33 3 Three line running STOP o35 setting 3 line running ,STOP function
fault reset command
4 Multi-speed command 1
FWD JOG command 34 5 Multi-speed command 2
REV JOG command 35 6 Multi-speed command 3 Synthesis of 16 multi-speed settings. See H
7 Multi-speed command 4 parameter Group
JOG order (as F35setting ) 36
8 multi-acceleration command 1
Acceleration and deceleration Synthesis of 8 acceleration settings. See H parameter
37 9 multi-acceleration command 2
prohibition command Group
10 multi-acceleration command 3
Motor 1、2 shift 38 11 multi-segment digital voltage 1
39 12 multi- segment digital voltage 2 Synthesis of 8 digital voltage settings. See H
Free stop
13 multi-segment digital voltage 3 parameter Group
Up command 40
The main set mode 1 of set
14
Down command 41 frequency
Automation program running The main set mode 2 of set
15 Synthesized frequency given to the way the main
42 frequency
fuction cancel switch. See F parameter group
The main set mode 3 of set
Automation program running stop 43 16
frequency
Program running start mode 44 The auxiliary setting mode 1 of
17
frequency set 1
Program running stop mode 45
The auxiliary setting mode 2 of Synthesized frequency secondary to the way a given
18 switch. See F parameter set
Pulse counter clearance 46 frequency set
47 19 The auxiliary setting mode 3 of
Pulse counter input

65 66
 Section V Parameter Function Table Section V Parameter Function Table

frequency set priority。

20 MSS timing running 1 Need to set E01 load model 9,E12 1pump is soft-start
21 MSS timing running 2 Synthetic Forward torque limit switch. See C control pump。
parameter set C15 53 2 pump soft-start Electric leverl spring,control 2 pump soft-start or
22 MSS timing running 3
stop。
23 Operation control mode shift 1
soft-start control must use 2 terminal control,stop
24 Operation control mode shift 2 priority。
Synthesis of 8 run-time switch. See H parameter set 54 2 pump stop
25 Operation control mode shift 3 Need to set E01 load model 9,E12 2pump is soft-start
26 Forward torque limit shift 1 control pump。
27 Forward torque limit switch 2 Synthesis of reverse torque limit switch. See C 55 3pump soft-start Electric leverl spring,control 3 pump soft-start or
28 Forward torque limit shift 3 parameter set C15 Group stop。
29 Reverse torque limit shift 1 soft-start control must use 2 terminal control,stop
56 3 pump stop priority。
30 Reverse torque limit shift 2 Synthesis of reverse torque limit switch. See C
Need to set E01 load model 9,E12 3pump is soft-start
31 Reverse torque limit shift 3 parameter set C16 Group
control pump。
57 4 pump start Electric leverl spring,control 4 pump soft-start or
Vector control mode, speed control mode and torque
stop。
control mode switching.
32 Torque speed shift Soft-start control must use two terminal control, stop
Disconnected status: Speed Control
58 4 pump stop has the priority.
Closed Status: torque control
Need setting E01 load style 9,E12 4 pump is
Detail C parameter set C18
soft-start control pump。
Edge-triggered, the fault occurred on the current
33 Fault reset command failure to confirm or not confirm electric level spring,automation multi-pump constant
59 Hand change order
water changed
34 FWD JOG command electromotion forward running command
the period of time water supply electric level spring, the period of time water supply
35 REV JOG command Electric reverse running command 60
change to zero change to zero
JOG command (as F35 Electric running the command, direction, set a
36
setting ) direction in accordance with F35.
Acceleration and deceleration To maintain the current state to prohibit the
37 o47 Input Terminal Polarity 0000～F7FF - 0000 Y
forbid commandr acceleration and deceleration movements.
Motor 1、2 change This parameter used to select every IO terminal is valid in which polarity and
38 Motor 1、2 shift Invalid status ：Motor 1 terminal running command is valid or not when power on.
Valid status ：Motor 2
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
39 Free stop Free stop machine 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
40 Up command Up order,detail A38~A42 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
41 Down command Down order,detail A38~A42 O4 DI1
Auto-run feature programs O3 DI2
42 Cancle program running function
canceled O2 DI3
Automatic procedures to O1 DI4
43 program running pause leave
unused DI5
suspend operation
AI3 DI6
44 program running start mode program running start mode AI2 DI7
45 program running stop mode program running stop mode AI1 DI8
Edge-triggered,frequency inverter pulse counter o53
46 pulse count clearance Clearance
0~10 bit Input Terminal Polarity 12~15 bit Output Terminal Polarity
47 pulse count input Edge-triggered, set the pulse counter input terminal
Edge-triggered, pulse-load preset counter o53 counts Low level valid（closed）
48 before count loading 0 0 Low level valid（closed）
to o54
Edge-triggered, pulse counter counts o55 maximum Falling edge valid, rising edge invalid
49 upper count loading
load o53
High level valid（disconnected）
External fault input, level-triggered, effective after 1 1 High level valid（cut off）
50 External fault signal input
the system reported E_Set failure. Rising edge valid, falling edge invalid
51 1 pump soft-start Electric leverl spring,control 1 pump soft-start or
stop。 Input Terminal Teponse
o48 0.001〜30.000 s 0.005 Y
52 1 pump stop soft-start control must use 2 terminal control,stop Time 0

67 68
 Section V Parameter Function Table Section V Parameter Function Table

Input Terminal Reponse 1：Clear up

o49 0.001〜30.000 s 0.005 Y
Time 1 Hundred： Define the status of the counter after power on
o48,o49 define Input terminal reponse time,through o50 select the reponse time according 0： Reload after power on
theterminal。 1： Clear up after power on
Input Terminal Reponse 2： Keep the status of the previous count
o50 0～07FF - 0 Y
Time Selection
Thousand ：Define o21～o24 is set to reach the preset count or counts to reach the maximum output
o48,o49 define Input terminal reponse time,through o50 select the reponse time according
signal delay time
theterminal。
The delay time of the input terminal is valid to the close and cut off action! 0： Count period, when reach this digital, keep this status valid , direct the change of the count。
Set the parameter choose Input terminal reponse time according every terminal. 1：the valid time of the output signal10ms,when reach this count, fixed keep the output status valid
10 9 8 7 6 5
2 2 2 2 2 2 2 2 2 2 2
4 3 2 1 0 10ms。
10 9 8 7 6 5 4 3 2 1 0 2：the valid time of the output signal 100ms,when reach this count, fixed keep the output status valid
DI1 100ms。
DI2 3：the valid time of the output signal 500ms,when reach this count, fixed keep the output status valid
DI3
DI4 500ms。
DI5
DI6 Maximum Pulse Input
DI7 o52 0.1～50.0 KHz 20.0 Y
DI8 Frequency
AI1 This parameter define the most pulse input frequency of analog setting frequency .
AI2
AI3 Input high signal frequency,only through multi-function input terminal Di8 as the pulse input
Setting 0~10 the polarity of input terminal terminal.
input pulse setting frequency according the the most input upper limit.
0 o48 input terminal reponse time 0 input pulse setting frequency,most input pulse frequency o52according the most output frequency
1 o49 input terminal reponse time 1 F12。
Pulse input frequency f_pulse corresponding setting frequency f_set formula ： f_set ＝
Circle counter operating 0 f_pulse/o52×F12。
Bit
Single cycle counter running 1 Pulse input analog setting,input most pulse frequency o52 according 100.0%。
Arrive at upper counter value Pulse input frequency f_pulse corresponding analog p_set formula：p_set＝f_pulse/o52×100.0％。
0
and reload o53 Current Counter Status 0~9999 - 0 Y
Ten
Arrive at upper counter value Y
1 o54 Preset Counter Setting 0~ o55 - 0
and clear savings
Upper Limit Counter
Power on to reload 0 o55 o54~9999 - 9999 Y
Setting
Counter power on to clear savings 1 When the pulse signal of the input terminal satisfy with the preset condition, Yi terminal output the
o51 Hundred - 0 Y
Collocation corresponding indication.
power on to keep previous
2
count status 1、DiX (X = 1 ~ 8) terminal is set to "pulse count input"; and set o54, o55.
Count period 0 DiX (X = 1 ~ 8) terminal is set to pulse counter clearance, terminal moves, the counter is
cleared.
Output signal valid time 20ms 1
Thousa DiX (X = 1 ~ 8) terminal is set to preset count loaded terminal moves, the counter load preset
Output signal valid time
nd 2 counts.
100ms
DiX (X = 1 ~ 8) terminal is set to the maximum counts loading terminal moves, the counter
Output signal valid time
3 load the maximum counts.
500ms
DiX counting 0 1 2 3 4 5 6 3 4 5 6 3
Bit： Control count mode
0：Circulate count,Arrive at upper counter value, ouput the arrival pulse（output terminal setting） o21 o54 o54
T T
1： single circulate count, after arrive at upper counter value, output the arrival pulse, stop running.
o22 o55 o55
Ten ： Operating after circulate mode reach upper limit count T T
the thousand of O51 set t
0：Reload

69 70
 Section V Parameter Function Table Section V Parameter Function Table

2, o21 ~ o24 output signal options: Pulse output ratio=10，output signal range 0~500hz。
o21 preset counts to reach the maximum count output signal after the effective time setted by o51. example：
o22 counts to reach the ceiling and reached the maximum counter output signal after the effective PL1pulse output option=2 actual frequency
time setted by o51. PL1 pulse output ratio=10
Counter pulse signal frequency range: 0 ~ 100Hz. Actual output pulse frequency=actual frequency/Max frequency*500hz
Virtual Terminal
o56 0000～F7FF - 0000 Y
Effective Selection PL2 pulse output option=3 actual current
This parameter is used to select a terminal whether each virtual terminal functionality is valid. PL2 pulse output ratio=20
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Actual output ratio frequency=Actual current percentage /200*1000hz
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

O4 DI1 Output Set Value Output Signal Range Definition

O3 DI2
No action 0 No output
O2 DI3
O1 DI4 Set frequency 1 0～Max frequency
leave
unused DI5
AI3 DI6 Actual
AI2 DI7 2 0～Max frequency
frequency
AI1 DI8
0～200%, corresponding paramerter：S03 output
Actual current 3
Setting 0~10 Virtual terminal valid choose current percentage
0 Actual input terminal valid
0～200%, correlation parameter：b02、b15 rated
1 Virtual input terminal valid Output voltage 4
voltages of motor
o57 DI1～4 Terminal Status 0000~1111 - - Y
DC bus voltage 5 0～1000VDC, 直流电压
o58 DI5～8 Terminal Status 0000~1111 - - Y
o59 AI1~3 Terminal Status 000~111 - - Y IGBT
6 0～100.0℃
temperature
o60 O1~4 Terminal Status 0000~1111 - - Y
Output power 7 0～200％
Make the actual terminal can only be effective check terminal state. Output torque 8 0～Max torque
Make the Virtual terminal can only be effective through register check terminal state.
No action 0 Actual torque
9 0～200% torque
Set frequency 1 value

Actual frequency 2
When F00 control model=2 close loop vector control，the function is invalid
Actual current 3

o61 PL1 Pulse Output Output voltage 4 - 0 Y

o62 PL2 Pulse Output DC bus voltage 5 - 0 Y 5-6 Multi-speed PLC Group
Last group Next group
IGBT temperature 6 Discription
/LCD Setting range Factory Change
Output power 7 Code Unit
Keyboard 7 segment LED Display setting limite
Output rpm 8 display

Actual torque 9 PLC Cancle 0

Bit
o63 PL1 Pulse Output Ratio 1～20 - 10 Y Multi-speed PLC intelligent 1
H00 - 0000 Y
Collocation Direction
o64 PL2 Pulse Output Ratio 1～20 - 10 Y
Ten decided by 0
PL1,PL2 Provide two-way isolated pulse output signal, it can analogy multiple output signals。 H40~H46

71 72
 Section V Parameter Function Table Section V Parameter Function Table

Direction decised Mode One-cycle

2
by Terminal and 1 command running
keyboard The zero speed
0
Deceleration and running when pause
10
acceleration time Fixed-speed running
0 1
decised by when the suspension
Hundred H26~H39 Stop with the
Time of acceleration parameters set when 0
and deceleration is 1 100 stop
decided by terminal Stop with the
1
Running time settings of start up
decised by 0 Running at the
H18~H25 speed when start up 0
Thousand
Running time 1000 segment
decised by 1 Running at the
1
terminal speed before stop
A bit: Program running functions intelligent Bit: Program running mode cycle
To use the program to run PLC functionality requires setting the bit to 1.
Multi-segment speed run only need to set the corresponding multi-stage o36 ~ o46-speed switching 0: single-cycle.
can be used without the need to set this parameter. 1: continuous cycle.
0: PLC program runs Cancel 2: single cycle, according to the 7 segment continuously runs, receives STOP command and stop.
1: PLC program runs intelligent Program runs in three ways as follows:
Ten: Define program runs or direction settings of multi-segment speed running
0: the direction decided by the H40 ~ H46 Example 1: The program runs single-cycle mode
1: The directiondecided by the keyboard or terminal output
Hundred: Define program runs or acceleration and deceleration time settings of multi-segment speed frequency
5X
running 60Hz
6X
0: deceleration time decided by the H26 ~ H39 50Hz
7X
1: The acceleration and deceleration time determined by terminal 40Hz
3X
Thousand: Set running time of defined program running 30Hz
2X
0: running-time decided by the H18 ~ H25 20Hz
1X
1: Running time decided by terminal 10Hz
0
4X time
10Hz
Bit Reserved T1 T2 T3 T4 T5 T6 T7

Program Running start Single circulation

10 0~15
up segment
Program running end
100 0~15 Example2:The program running continuous cycle mode
segment
Program Output signal valid putput
H01 Running 0 - 0710 Y frequency
time 8ms 5X 5X
Configuration 60Hz
Output signal valid 50Hz 6X 6X
1
time 20ms 40Hz 7X 7X
1000 3X 3X
Output signal valid 30Hz
2 20Hz 2X 2X 2X
time 100ms
10Hz 1X 1X 1X
Output signal valid
3 0
time 500ms 4X 4X time
10Hz
A bit: function reserved
program
Ten: Defining the program running start up segment running
Hundred: Defining the end segment of the program running STOP
Thousand: Defining valid time of program running output signal. Continuous circulation
time

Program single-cycle 0
H02 Bit - 0000 Y
Running Continuous Cycle 1

73 74
 Section V Parameter Function Table Section V Parameter Function Table

Example 3: The program is running in the single cycle, according to the 7 segment of the speed
running mode output
frequency 3X 3X
output
2X 2X
frequency
5X 1X 1X
60Hz
50Hz 6X

40Hz 7X
T1 T2 X T1 T2 time
30Hz 3X
2X dt1' at1'
20Hz
10Hz 1X RUN
0 STOP
10Hz 4X time Note:
program at1 ':the acceleration time at the acc time at1;
running dt1': the deceleration time at the dcc time dt1 ;
STOP at3 ': the acceleration tim at the acc time at3;
time
Single circulation, continuous running at step 7 speed dt3': the deceleration time at the dcc time dt3
Ten: The running status when pause
0: The zero speed running when pause. Lower frequency ~ upper
1: Fixed-speed running when the suspension H03 1 Segment Speed Setting 1X Hz 5.00 Y
frequency
Hundred: run segment when stop Lower frequency ~ upper
0: Stop with the parameters set when stop H04 2 Segment Speed Setting 2X Hz 30.00 Y
frequency
1: Stop with the settings of start up Lower frequency ~ upper
Thousand : Running segment when start up. H05 3 Segment Speed Setting 3X Hz 20.00 Y
frequency
0: Running at the speed when start up segment
1: Running at the speed before stop Lower frequency ~ upper
H06 4 Segment Speed Setting 4X Hz 30.00 Y
frequency
Example: Hundred = Stop with the parameters set when stop Lower frequency ~ upper
H07 5 Segment Speed Setting 5X Hz 40.00 Y
Thousand = 0 Running at the speed when start up segment frequency
Lower frequency ~ upper
output H08 6 Segment Speed Setting 6X Hz 45.00 Y
frequency
frequency 3X 3X
2X 2X Lower frequency ~ upper
H09 7 Segment Speed Setting 7X Hz 50.00 Y
F51=00 1X 1X frequency
Lower frequency ~ upper
time
H10 8 Segment Speed Setting 8X Hz 5.00 Y
T1 T2 X T1 T2 frequency
dt3' at1' Lower frequency ~ upper
H11 9 Segment Speed Setting 9X Hz 30.00 Y
RUN frequency
STOP Lower frequency ~ upper
H12 10 Segment Speed Setting 10X Hz 20.00 Y
frequency
Example: Hundred = 0 Stop with the parameters set when stop Lower frequency ~ upper
Thousand = Running at the speed before stop H13 11 Segment Speed Setting 11X Hz 30.00 Y
frequency
Lower frequency ~ upper
5X H14 12 Segment Speed Setting 12X Hz 40.00 Y
frequency
output 4X
Lower frequency ~ upper
frequency 3X 3X H15 13 Segment Speed Setting 13X Hz 45.00 Y
2X frequency
X+Y=T3
F51=01 1X Lower frequency ~ upper
H16 14 Segment Speed Setting 14X Hz 50.00 Y
frequency
T1 T2 X Y T4 time Lower frequency ~ upper
H17 15 Segment Speed Setting 15X Hz 50.00 Y
dt3' at3' frequency
RUN
STOP 1X

Example：hundred=1 As start parameter is set to shut down

Thousand=1 stop front-end speeds

75 76
 Section V Parameter Function Table Section V Parameter Function Table

Set the frequency of program running and the running frequency of 7-segment speed Acceleration and deceleration time and the direction of running
respectively. short-circuit the multi-terminal command 1,2,3,4 with COM
combinatorially to realized the 16-segment speed/acceleration speed.
0X-7X 8X-15X
0X speed is the regular running mode, setting source can be adjusted by F02, F03 and other
parameters, running time is controlled by the H18. 0X -7X Direction controlled
0
by parameter 8X-15X Direction
H00
Terminal multi-segment speed is defined as follows（shorted with COM it is ON,disconnected then it controlled by keyboard
10 0X -7X Direction controlled
is OFF） ： and terminal
1
by keyboard and terminal
Speed
0X 1X 2X 3X 4X 5X 6X 7X
Terminal
0X -7Xdeceleration and
Multiterminal-speed 0 accelertation time
OFF ON OFF ON OFF ON OFF ON 8X-15Xdeceleration
Command 1
H00 controlled by parameter and accelertation time
100 0X -7X deceleration and controlled by keyboard
Multiterminal-speed 1 accelertation time and terminal
OFF OFF ON ON OFF OFF ON ON
Command 2
controlled by terminal

0X -7Xrunning time
0
Multiterminal-speed H00 controlled by paremeter 8X-15Xrunning time
OFF OFF OFF OFF ON ON ON ON
Command 3 1000 0X -7Xrunning time controlled by terminal
1
controlled by terminal

Multiterminal-speed
OFF OFF OFF OFF OFF OFF OFF OFF
Command 4

8X 9X 10X 11X 12X 13X 14X 15X

Multiterminal-speed
OFF ON OFF ON OFF ON OFF ON
Command 1
H18 0 Segment Running Time T0 0.0～3200.0 s 2.0 Y
Multiterminal-speed H19 1 Segment Running Time T1 0.0～3200.0 s 2.0 Y
OFF OFF ON ON OFF OFF ON ON
Command 2 H20 2 Segment Running Time T2 0.0～3200.0 s 2.0 Y

H21 3 Segment Running Time T3 0.0～3200.0 s 2.0 Y

Multiterminal-speed H22 4 Segment Running Time T4 0.0～3200.0 s 2.0 Y
OFF OFF OFF OFF ON ON ON ON
Command 3
H23 5 Segment Running Time T5 0.0～3200.0 s 2.0 Y

H24 6 Segment Running Time T6 0.0～3200.0 s 2.0 Y

Multiterminal-speed
ON ON ON ON ON ON ON ON Y
Command 4 H25 7 Segment Running Time T7 0.0～3200.0 s 2.0
Actual running time equals to the set multi-segment running time multiples a time
which is times of speed running time, and such actual running time decided by the tens
digit of H40~H46. Please refer to H40~H46.
H26 1 Segment Acceleration Time at1 0.0～3200.0 s 10.0 Y

H27 1 Segment Deceleration Time dt1 0.0～3200.0 s 10.0 Y

H28 2 Segment Acceleration Time at2 0.0～3200.0 s 10.0 Y

H29 2 Segment Deceleration Time dt2 0.0～3200.0 s 10.0 Y

77 78
 Section V Parameter Function Table Section V Parameter Function Table

H30 3 Segment Acceleration Time at3 0.0～3200.0 s 10.0 Y 6 Segment Speed Deceleration time：×hours 2
Y Configuration
H31 3 Segment Deceleration Time dt3 0.0～3200.0 s 10.0
Word
H32 4 Segment Acceleration Time at4 0.0～3200.0 s 10.0 Y
7 Segment Speed Deceleration time：×days 3
H33 4 Segment Deceleration Time dt4 0.0～3200.0 s 10.0 Y Configuration
Y Word
H34 5 Step Acceleration Time at5 0.0～3200.0 s 10.0
Y In program multi-speed l running, the digit parameters decide the direction of each
H35 5 Segment Deceleration Time dt5 0.0～3200.0 s 10.0
Y
speed.
H36 6 Segment Acceleration Time at6 0.0～3200.0 s 10.0
H37 6 Segment Deceleration Time dt6 0.0～3200.0 s 10.0 Y
Running Direction Setting Value
H38 7 Segment Acceleration Time at7 0.0～3200.0 s 10.0 Y
forward 0
H39 7 Segment Deceleration Time dt7 0.0～3200.0 s 10.0 Y
reverse 1
Set the Acc/Dec time of 7 steps respectively. They determine the time When running control mode F05＝0/1/2, these parameters decide the direction of each
needed to reach the speed, respectively depending on the acceleration time for speed.
acceleration or on the deceleration time for deceleration, but the time is not the When running control mode F05＝3, the setting value and terminal FWD/REV decide
actual time needed. Actual acc/dec time equals to the set acc/dec time multiples the direction of each speed together. FWD is prior.
a time multiple which is decided by the hundreds and thousands digit of
H40~H46. Please refer to H40~H46. FWD=1 FWD=1
Definite acceleration and deceleration time for multi-step speed： Setting
Running Running
Value
direction direction
output forward reverse 0
frequency 2X
reverse forward 1
Ten bit：Unit of program running multi-segment speed running time.
1X 3X
Running Time Tens bit Range（e.g.H18~H25=3200.0）
T1 T2 T3 ×seconds 0 3200.0 seconds
at1 dt2 dt3 ×minutes 1 3200.0 minutes
time
at2
×hours 2 3200.0 hours
Definition of multi-step speed acceleration/deceleration time
×days 3 3200.0 days
Remark：at1：1 segment accelerationtime;at2：2 segment acceleration time;dt2：2 segment Hundred bit,K bit : Unit of program running multi-segment speed acc/deleration running
deceleration time;dt3：3 segment deceleration time. Acceleration KB,
Range（e.g.H26~H39=3200.0）
/Decelatationtime 100
1 Segment Speed Running direction：forward 0
bit ×second 0 3200.0 seconds
Configuration Running direction：reverse 1
×minute 1 3200.0 minutes
Word
Running time：×seconds 0
2 Segment Speed ×hour 2 3200.0 hours
H40 Configuration Running time：×munites 1 - 0000 Y
10 ×day 3 3200.0 days
H41 Word Running time：×hours 2 - 0000 Y
H47 0 Segment Digital Voltage Giving -100.0~100.0 % 0.0 Y
H42 3 Segment Speed Running time：×days 3 - 0000 Y
H43 Configuration - 0000 Y H48 1 Segment Digital Voltage Giving -100.0~100.0 % 10.0 Y
H44 Word Acceleration time：×seconds 0 - 0000 Y H49 2 Segment Digital Voltage Giving -100.0~100.0 % 20.0 Y
H45 4 Segment Speed Acceleration time：×munites 1 - 0000 Y
100 H50 3 Segment Digital Voltage Giving -100.0~100.0 % 30.0 Y
H46 Configuration Acceleration time：×hours 2 - 0000 Y
Word H51 4 Segment Digital Voltage Giving -100.0~100.0 % 40.0 Y
Acceleration time：×days 3
5 Segment Speed H52 5 Segment Digital Voltage Giving -100.0~100.0 % 50.0 Y
Configuration Deceleration time：×seconds 0
1000 H53 6 Segment Digital Voltage Giving -100.0~100.0 % 60.0 Y
Word Deceleration time：×munites 1

79 80
 Section V Parameter Function Table Section V Parameter Function Table

H54 7 Segment Digital Voltage Giving -100.0~100.0 % 70.0 Y

Digital voltage set function can analogy give frquency,select by F02,F03;analogy give PID set or 5-7 V/Fcurve Group
feedback, select by P02,P03;it cand be shifted by the input terminal o36~o46. Upper group Next group
bit Current speed step 0～0xF Description/LCD Setting Range Factory Change
Code Unit
Current acceleration Keyboard Display 7 Segment LED Display Setting Limit
10 0～0x7 U00 V/Fsetting Frequency1 0.00～U02 Hz 5.00 N
segment
Multi-speed User-defined the first frequency value of V / F curve, corresponding to V1
H55 Current running time - - N
Status 100 0～0x7
segment output voltage
max
Current digit voltage output
1000 0～0x7
segment
V8
Bit：Current speed segment
0～16 segment,In hex,can be shift by o36～o46 V7
Ten bit：Current acceleration segment V6
0～7 segment,in hex,can be shifted by o36～o46 V5
V4
Hundred bit：Current running time segment V3
0～7 segment,in hex,can be shifted by o36～o46,valid when program running V2
V1
KB：Current digital voltage segment
(0,0) F1 F2 F3 F4 F5 F6 F7 F8 max output frequency
0～7 segment,in hex,can by shifted by terminal o36～o46 frequency

U01 V/F Setting Voltage 1 0～U03 % 10 N

User-defined the first voltage percentage of V / F curve, on the base of rated output voltage 100% of
frequency converter, corresponding to F1..
U02 V/F Setting Frequency 2 U00～U04 Hz 10.00 N
User-defined the second frequency value of V / F curve, corresponding to V2
U03 V/F Setting Voltage 2 U01～U05 % 20 N
User-defined the second voltage percentage of V / F curve, on the base of rated output voltage 100%
of frequency converter, corresponding to F2..
U04 V/F Setting Frequency 3 U02～U06 Hz 15.00 N
User-defined the third frequency value of V / F curve, corresponding to V3
U05 V/F Setting Voltage 3 U03～U07 % 30 N
User-defined the third voltage percentage of V / F curve, on the base of rated output voltage 100% of
frequency converter, corresponding to F3.
U06 V/F Setting Frequency 4 U04～U08 Hz 20.00 N
User-defined the fourth frequency value of V / F curve, corresponding to V4.
U07 V/F Setting Voltage 4 U05～U09 % 40 N
User-defined the fourth voltage percentage of V / F curve, on the base of rated output voltage 100% of
frequency converter, corresponding to F4.
U08 V/F Setting Frequency 5 U06～U10 Hz 25.00 N
User-defined the fifth frequency value of V / F curve, corresponding to V5.
U09 V/F Setting Voltage 5 U07～U11 % 50 N
User-defined the fifth voltage percentage of V / F curve, on the base of rated output voltage 100% of
frequency converter, corresponding to F5.
U10 V/F Setting Frequency 6 U08～U12 Hz 30.00 N
User-defined the sixth frequency value of V / F curve, corresponding to V6.
U11 V/F Setting Voltage 6 U09～U13 % 60 N

81 82
 Section V Parameter Function Table Section V Parameter Function Table

User-defined the sixth voltage percentage of V / F curve, on the base of rated output voltage 100% of PID abnormity treatment:
frequency converter, corresponding to F6. 1: Warning & Continuous running: continue ruuning after abnormity feedback signal.
U12 V/F Setting Frequency 7 U10～U14 Hz 35.00 N 2: Warning & Decelerating stop: decelerate and stop after abnormity feedback signal.
User-defined the seventh frequency value of V / F curve, corresponding to V7. 3: Warning & Free stop: free stop after abnormity feedback signal .
U13 V/F Setting Voltage 7 U11～U15 % 70 N
User-defined the seventh voltage percentage of V / F curve, on the base of rated output voltage 100% P01 PID Output Limit 0～100 % 100 Y
of frequency converter, corresponding to F7. The parameter defines the limited range of the output when using PID control.
U14 V/F Setting Frequency 8 U12～most frequency Hz 40.00 N
User-defined the eighth frequency value of V / F curve, corresponding to V8. Set frequency by keyboard or RS485 0
U15 V/F Setting Voltage 8 U13～100 % 80 N
AI1 external analogy giving 1
User-defined the eighth voltage percentage of V / F curve, on the base of rated output voltage 100%
of frequency converter, corresponding to F8. AI2 external analogy giving 2
Feedback Signal
P02 AI3 external analogy giving 3 - 1 Y
Selection
5-8 PID parameter
Upper group Next group Keyboard potentiometer giving 4
Description
Set Range Factory Modify muti-step digital voltage giving 5
Code /LCD Unit
7 Segment LED Display Set Limitation
Display Digital pulse set 6
Unidirection
0 PID feedback signal selection,can select keyboard/Rs485,potentiometer,digital voltage,digital pulse for
Bit regulation
feedback signal.
Bidirection regulation 1

Negative effect 0 Set frequency by keyboard or RS485 0

10
Positive effect 1 AI1 external analogy giving 1

PID fault, N action 0 AI2 external analogy giving 2

PID Setting Signal
P00 Warning & - 0000 N P03 AI3 external analogy giving 3 - 2 Y
Configuration 1 Selection
Continuous running Keyboard potentiometer giving
100 4
Warning &
2
Decelerating stop muti-step digital voltage giving 5
Warning & Free stop 3
Digital pulse set 6
- - PID giving signal selection,can select keyboard/Rs485,potentiometer,digital voltage,digital pulse for
1000 giving signal.
- -
When the inverter receives start command, it can control output frequency automatically in the PID P04 Keyboard Set Signal 0.0～100.0 % 50.0 Y
regulation mode after comparing the setting signal and feedback signal from terminal. The process is
When P03 is 4, the setting pressure set by the keyboard. 0.0~100.0% is 0 to the maximum pressure
explained as following:
respectively.
setting signal
+ f
PID inverter M
-
feedback signal
( = setting signal - feedback signal)
PI8000/PI8100 PID regulation
0: negative action, when Δ is positive, frequency rises and when Δ is negative, frequency falls.
1: positive action, when Δ is positive, frequency falls and when Δ is negative, frequency rises.

83 84
 Section V Parameter Function Table Section V Parameter Function Table

P05 PID integral time integral time 0.002～10.000 s 0.250 Y P08 PID Sampling Period 0.002～10.000 s 0.010 Y

difference Set Sampling period of feedback signal.

When set this parameter small, the system response speed to the giving and feedback deviation is slow, but control is
stable.
time
When set this parameter low, the system response speed to the giving and feedback deviation is slow, but easy to cause
operation value vibration

P09 Deviation Limit 0.0～20.0 ％ 5.0 Y

time
0.002～10.000s Deviation limit effects system control accuracy and stability.
The parameter determines the integral regulation speed, the regulation acts on the difference between When the deviation of feedback singnal and giving signal <deviation limit, PID N regulation,keep
PID feedback and getting value by PID regulator. output stable.
When the difference between PID feedback and getting value is 100%, integral regulator continues to When the deviation of feedback singnal and giving signal >deviation limit,PID regulates according to
regulate output to(P01×F13×12.5%)Hz during the PID integral time.(single direction PID regulation, deviation, update output
ignores proportion and differential effect). P10 PID Fault Detect Time 0.0～3200.0 s 0.0 N
If the value is great, the control is stable but response is slow; if the value is little, the system response
PID Fault Detected
is rapid but perhaps surge occurs. P11 0.0～100.0 % 10.0 N
Value
P06 PID Differencial Time 0.000～10.000 s 0.000 Y
Set P10 to 0. 0 for N fault inspection.
0.000～1.000s When PID feedback signal <P11 set PID fault inspection value,last P10set time,regard it as PID
The parameter determines the regulation intensity, the regulation acts on the change ratio regulation fault.
of the difference between PID feedback and getting value by PID regulator.
P12 PID Display Range 0.00～100.00 - 1.00 Y
When the change ratio of the difference between PID feedback and getting value is 100%
in the differential time, PID regulator regulates output to(P01×F13×12.5%)Hz (single A09 PID set value＝PID set value（％）×P12
direction PID regulation, ignores proportion and integral effect). A10 PID feedback value＝PID feedback value（％）×P12
If the value is great, the greater the intensity is, the system surge is to occur more easily If PID feedback 10V corresponding 4.0Mpa pressure ,if need A09,A10 to display actual value,only
P07 PID Proportion Gain 0～1000.0 % 100.0 Y need to set P12 = 0.04.

0～100.0%
The parameter difines regulation intensity of PID regulator, the larger the P is, the more
the intensity is.
When proportion gain is 100%, and the difference between PID feedback and getting
value is 100%, PID regulator’s output is(P01×F13×12.5%)Hz(single direction PID
regulation, ignores differential and integral effect).
Proportion gain is the parameter decides PID regulator’s response extent.
If the gain is great, the response is rapid, but if too great, the surge will occur; the gain is
little, the response will lag.
difference

time

operation value

time

85 86
 Section V Parameter Function Table Section V Parameter Function Table

r
5-9 Extention parameters s
Upper group Next group
Electromagnetic
Description
Set Range Factory Modify E09 Switch Action 0.000～10.000 s 0.500 Y
Code /LCD Unit
7 Segment LED Display Set Limit Delay
Keyboard Display
General 0 Pumps Shift
E10 0～9999 s 5 Y
Pump 1 Judging Time
Fan 2 Decelerating
0
stop
Injection machine 3
Variable
Textile machine 4 bit Stop mode
frequency 1
Hoist machine 5 pump stop
Kowtow Machine 6 Free stop 2
belt conveyor 7 Keep current
E00 Load Type - 0 N Pumps 0
Variable frequency power 8 situation
Constant 10 status when
Multi-pumps constant All-pumps
9 Pressure Water fault occurs 1 -
pressure water supply E11 stop 0000 N
Supply
Reserved 10 Variable
Configuration
frequency to
Reserved 11 0
working
Torque control 12 Alternation
100 frequency
shift mode
Voltage regulation power 13 Variable
Current regulation power 14 frequency to 1
Starting Pressure stop
E01 0.0～100.0 % 10.0 Y
Deviation Pump status Keep status 0
1000
Starting Delay keep Stop reset 1
E02 0.0～3200.0 s 5.0 Y
Time Pump 1 invalid 0
E03 Stop Frequency 0～50.00 Hz 5.00 N Pump 1 variable frequency to
1
bit control pump
E04 Stop Delay Time 0.0～3200.0 s 5.0 Y
Pump 1 soft starts to control
High Pressure 2
E05 0～100.0 % 90.0 Y pump
Arrival Value
Pump 2 invalid 0
Low Pressure
E06 0～100.0 % 10.0 Y Pump 2 variable frequency to
Arribal Value 1
10 control pump
Timing invalid 0 Pump 2 soft starts to control
bit water 2
Valid 1 Multi-pumps pump
supply E12 - 1111 N
Congfiguration Pump 3 invalid 0
Set
Pump 3 variable frequency to
according to 0 1
100 control pump
Timing To Supply Pressure P03
E07 10 - 0000 Y Pump 3 soft starts to control
Water giving Set 2
pump
according to 1
Pump 4 invalid 0
H47～H54
Pump 4 variable frequency to
Timing Circle mode 0 1
100 1000 control pump
mode Single circle 1
Pump 4 soft starts to control
1000 Current timing step 2
pump
H Pump 1 stop 0
Timing Shift Multi-pumps
E08 0.0～3200.0 o 0.0 N E13 Bit Pump 1 run in variable - 0000 N
Alternation Time Status 1
u frequency

87 88
 Section V Parameter Function Table Section V Parameter Function Table

Pump 1 run in working C00 Filter Time Of Speed-loop 2～200 ms 10 是

2
frequency It defines the filter time of the speed-loop. The range is 0.01~100s.If the value is too
Pump 2 stop 0
great, the control is stable but response is slow; if the value is too little, the system
Pump 2 run in variable
1 response is rapid but perhaps is unstable. So it is necessary to consider the stability and
10 frequency
the response speed at the same time when setting the value.
Pump 2 run in working
2 C01 Speed-loop Low Speed Ti 0.01～100.00 s 0.15 Y
frequency
Pump 3 stop 0 It defines the integral time of the speed-loop low speed. The range is 0.01~100.00s.
Pump 3 run in variable If the integral time is too great, response is slow and the control of external disturbing
1 signal become bad; if the time is too little, response is rapid, but perhaps brings the surge.
100 frequency
Pump 3 run in working C02 Speed-loop Low Speed Td 0.000～1.000 s 0.000 Y
2
frequency It defines the differential time of the speed-loop low speed segment and the range is
Pump 4 stop 0 0.000~1.000s. If the time is great enough, the surge which is caused by P action when
Pump 4 run in variable difference occurring can attenuate quickly. But too great, the surge will happen contrary.
1
1000 frequency When the time is little, the attenuation function is little too.
Pump 4 run in working
2 C03 Speed-loop Low Speed P 0～200 % 150 Y
frequency
It defines the proportion gain of speed loop low speed segment.And the range is
Pump 1 stop 0
Bit 0~1000%.If the gain is great, the response is rapid, but too great, surge perhaps occurs; if
Pump 1 soft-start 1
the gain is too little, response is slower.
Pump 2 stop 0
10 Speed-loop Low Speed Shift
Soft Starting Pump 2 soft-start 1 C04 0.0~C08 Hz 7.00 Y
E14 - 0000 Y Frequency
Pump Control Pump 3 stop 0
100 Pump 3 soft-start 1 It defines low-speed loop switching frequency, the parameter and switching frequency at
Pump 4 stop 0 high-speed optimize Speed-loop PID parameter.
1000
Pump 4 soft-start 1 C05 Speed Loop High Speed Ti 0.01～100.00 s 0.50 Y
User Y It defines integration time of High-speed section of the speed loop. Range is 0.01～100.00s. integration time too
E15 0～9999 - 0
Parameter 0 large and unresponsive, external interference control variation becomes weak; integration time is small the reaction
User Y speed, oscillation occurs when it is too small.
E16 0～9999 - 0
Parameter 1
C06 Speed Loop High Speed Td 0.000～1.000 s 0.000 Y
User 0～9999 Y
E17 - 0 It defines the differential time of the speed-loop high speed segment and the range is
Parameter 2
User 0～9999 Y 0.000~1.000s. If the time is great enough, the surge which is caused by P action when
E18 - 0
Parameter 3 difference occurring can attenuate quickly. But too great, the surge will happen contrary.
User 0～9999 Y When the time is little, the attenuation function is little too.
E19 - 0
Parameter 4 C07 Speed Loop High Speed P 0～100 % 150 Y
User 0～9999 Y
E20 - 0 It defines the proportion gain of speed loop high-speed section, range from 0～1000%. Gain is
parameter 5
large, response speed, but too large gain will occur vibration; if the gain is small, the reaction lag.
User 0～9999 Y
E21 - 0 Speed Loop And High-speed
Parameter 6 C08 C04~max frequency Hz 30.00 Y
Switching Frequency
User 0～9999 Y
E22 - 0 It defines Intergral time of speed loop high speed,the parameter and switching frequency at
Parameter 7
low-speed optimize the speed-loop PID parameter.
User 0～9999 Y
E23 - 0 C09 Low-speed Slip Gain 0~200 % 100 Y
Parameter 8
※Please check appendix 4 for the detailed extention parameter instruction. low-speed segment slip compensation gain
Low Speed Slip Switching
5-10 Speed-loop parameter [SPD] C10 0~C12 Hz 5.00 Y
Frequency
Upper group Next group
Description/LCD Set Range Factory Modify Low speed sement slip compensation switching frequency
Code Unit
Keyboard Display 7 Segment LED Display Set Limit C11 High Speed Slip Gain 0~200 % 100 Y

89 90
 Section V Parameter Function Table Section V Parameter Function Table

High speed segment slip compensation gain Torque accelerate time,Torque acccelerate time from 0 to 300.0%
High Speed Slip Switching C22 Torque Deceleration Time 0.0～200.0 S 1.0 Y
C12 C10~ max frequency Hz 30.00 Y
Frequency
Torque decelerate time,Torque decelerate time from 300.0% to 0
High speed segment slip compensation switching frequency
Low Speed Exitation
C13 Upper Froward Torque 0.0~300.0 % 200.0 Y C23 0~100 ％ 30 Y
Compensation
This parameter is a ratio, that is, the user can set the maximum forwarding torque. Under low speed,compensate exitation quantity, increase torque feature, in case of meetingthe
requirement, try to make it lower, could reduce the motor heatingup caused by magnetic path full.
C14 Upper Reverse Torque 0.0~300.0 % 200.0 Y
C24 Current Loop Ti 0～9999 ms 500 Y
This parameter is a ratio, that is, the user can set the maximum reversing torque.
Define the current loop intergral time. When Intergral time is too long, response is inactive; the alibity
Sey by keyboard or RS485 0
to control external jamming becomes weak. When intergral time is short, response is fast,if too short,
AI1external alalogy giving 1 vibration will occur.
AI2 external alalogy giving 2 C25 Current Loop P 0～1000 % 100 Y
Froward Torque Set
C15 AI3 external alalogy giving 3 - 0 Y Define current loop proportion gain, When select big gain, response fast, but too big will occur
Mode
Keyboard potentiometer giving 4 vibration. when select low gain, response lag.

muti-step digital voltage giving 5 C26 PG Electronic Gear A 1~5000 - 1 Y

Digital pulse set 6 C27 PG Electronic Gear B 1~5000 - 1 Y

When encoder and motor is in different shaft, can calculate current motor speed according to encoder
Keyboard set or RS485 0
and gear ratio.
AI1 external alalogy giving 1 Electronic gear A for denominator,B for molecule。
AI2 external alalogy giving 2 C28 PG Pulse 300～9999 - 2500 N
Reverse Torque Set
C16 AI3 external alalogy giving 3 - 0 Y PG pulse quantity used,set value is the pulse quantity when motor rotates for a circle.
Mode
Keyboard potentiometer giving 4 N PG break protection 0
muti-step digital voltage giving 5 Action When PG Warning and keeping running 1
C29 - 3 Y
Digital pulse set 6 Break Warning and deceleration stop. 2
C17 Torque Set Gain 0.0~300.0 % 200.0 Y Warning and free stop. 3
Froward torque set mode and reverse torque set mode, can select keyboard/RS485, Set the brake method when detect PG break.
potentiometer,digital voltage,digital pulse for giving signal. 0：N PG break protection
0：keyboard set,set by C13、C14.
1： Warning and keeping running.
1～6：C13 forward torque upper =set value percentage×C17 torque giving gain
2： Warning and deceleration stop.
C14 reverse torque upper = set value percentage×C17 torque giving gain
3： Warning and free stop.
e.g.：C15 forward torque giving method=4 keyboard pretentimometer giving
when keyboard pretentimometer giving A47=100%,C17=200.0%, PG Rotating When motor forward,phase A leads 0
C30 - 0 Y
C13 forward torque upper =100%×200.0%=200.0% Direction When motor forward, phase A leads 1
Speed control 0
C18 Speed /Torque Control Shift - 0 Y
Torque control 1
phase A phase A
F00 control method is to selecte senseless vector control or sensor feedback close loop vector control,
can change speed or torque control through input terminal. After setting IP terminal change, keyboard set
invalid, only for query. phase B phase B

C19 Forward Speed Limit 0.00~Maxmum frequency - 50.00 Y phase B is forward

phase A is forward
Forward speed limit when torque control Encoder rotating direction,refer to the motor forward direction
C20 Reverse Speed Limit 0.00~ Maxmum frequency - 50.00 Y 0：When motor forward,phase A leads,set C27= 0
Reverse speed limit when torque control. 1：When motor forward,phase B leads,set C27= 1
Note：above parameters are valid when with encoder(PG), need to layout PG card. If needed, please
C21 Torque Acceleration Time 0.0～200.0 S 1.0 Y
contact our company.

91 92
 Section V Parameter Function Table Section V Parameter Function Table

C31 PG Dropped Inspection Time 0.0~10.0 s 1.0 N N measurement 0

OG feedback signal is 0, exceed C31 set time, system reports PG dropped fault. Set speed to 0, or Motor Parameter calculate by lable data 1
b11 - 0 N
sert C31 to 0, don’t check PG dropped fault. Measurement inverter static messurement 2
inverter rotation messurement 3
Set whether the measurement of electrical parameters in order to b10 motors choose motor 1 as an
example.
0: N measurement
5-11 motor parameter [MOT] 1: Calculate by lable data
Upper group next group
According to the motor nameplate parameters b00 ~ b04, automatic calculation b05 ~ b09 and other
Description/LCD Set range Factory Modify
Code Unit electrical parameters, the advantage does not require power-on self-tuning, suitable for general-purpose Y
Keyboard Display 7 Segment LED Display Set Limit
Motor 1 Rated series of four pole motor, the other type motor can be adjusted based on this parameter.
b00 0.00～Maximum frequency Hz 50.00 Y 2: Inverter static measurement
Frequency
b01 Motor 1 Rated Current y09*(50%～100%) A ★ Y If the motor parameters can not be measured without load, you can choose static frequency converter
Y measurement. Make sure that motor in a static static, after static measurement, it can be manually adjusted
b02 Motor 1 Rated Voltage 100～1140 V ★
some parameters, optimal control.
b03 Motor 1 Pole-pairs 1～8 - 2 Y
The b11 is set to 2, the inverter automatically start parameter determination.
b04 Motor 1 Rated Speed 500～5000 rpm 1480 Y
Keyboard figures area show "-RUN": waiting to run the command, start the measurement.
b00~b04 are the motor’s nameplate parameters which touch the precision.Set the parameters according to Keyboard figures area show "CAL1", inverter without output.
the motor’s nameplate. Keyboard figures area show "CAL2", inverter with output, static state.
b00 ~ b04 motor nameplate in parameters, it is necessary to re-calculate motor parameters by using b11. Keyboard figures area show "-END": measuring ends.
Excellent vector control performance requires exact motor parameters. Exact parameters are base on the Keyboard figures area show "E. CAL": the measurement process errors.
correct setting of motor’s rated parameters. Process can be measured through the STOP key to stop.
To assure the control performance, please match the right motor as per the inverter’s standard, motor 3: Inverter rotation measurement
rated currentis limited between 30%~120% of inverter rated current. Motor can be measured without load, can choose the rotation measurement. Measurements started,
The rated current can be set, but can’t be more than the rated current of the inverter. The parameter
make sure the motor is static.
confirms the OL protection capability of the motor and energy-saving running.
Static measurement converter, the output DC voltage, pay attention to safety.
To prevent self-cooled motor form overheat when running in a low speed , and the motor capacity change
The b11 is set to 3, the inverter automatically start parameter determination.
when motor character change little, the user can correct the parameter to protect the motor.
Keyboard figures show that the regional show "-RUN": waiting to run the command, start the
The number of motor pole pairs, such as the four pole motor, the number of pole pairs is set to 2
measurement.
b05 Motor 1 N Load Current 0.0～b01 A ★ Y
Keyboard figures area show "CAL1", "CAL3": N output inverter.
b06 Motor 1 Stator Resistance 0.000～30.000 ohm ★ Y
Keyboard figures area show "CAL2", inverter with output, under static state.
b07 Motor 1 Rotor Resistance 0.000～30.000 ohm ★ Y Keyboard figures area show "CAL4", inverter with output, the motor forward in high-speed.
b08 Motor 1 Stator Inductance 0.0～3200.0 mH ★ Y Keyboard figures area show "-END": measuring the end.
Y Keyboard figures area show "E. CAL": the measurement process errors.
b09 Motor 1 Mutual Inductance 0.0～3200.0 mH ★
Process can be measured through the STOP key to stop.
b05～b09 can by input by motor actual parameters value,also can define motor parameterby b11
parameter messure function.and save automatically.If know the correct motor parameter, can input by
Set this parameter, the motor parameters will be determined dynamically. Be sure the motor is without
hand
load (N-load operation).
When b11 is 1,2,3,the system calculates and measuresautomatically.
Before setting, be sure to run well prepared, the motor will run in high speed during the measurement.
b05~b09 is the motor’s basic electric parameters, these parameters is essential to achieve
Measurement is completed, b11 return to 0. The measured parameters will select parameters on the base of
vector control calculation.
b10 motor parameters which is automatically saved to the b05 ~ b09 or b18 ~ b22.
Motor 1 0
b10 Motor Selection - 0 N
Motor 2 1 Note：
The system can select any group motor parameters. Before auto-messure the motor parameter,must input motor rated parameter b00～b04or b13～17
Motor parameter messurement modify and save to corresponding motor parameter area automatically. correctly

93 94
 Section V Parameter Function Table Section V Parameter Function Table

Please regulate accelerating and deceleration time or torque increasing parameter, if there is N action 0
over-current or over voltage faults while auto-messurement. Reset system parameter with
1
When automatic regulation, motor should be in stop status. keyboard memory area1
Vector Control Ctarting Not inspection R1 0 Reset system parameter with
b12 - 0 N 2
Inspection R1 keyboard memory area2
Inspection R1 1 Parameter Upload To
y01 Reset system parameter with - 0 N
Keyboard 3
b13 Motor 2 Rated Frequency 0.00～Maxmum frequency Hz 50.00 Y keyboard memory area3
b14 Motor 2 Rated Current y09*(50%～100%) A ★ Y Reset system parameter with
4
b15 Motor 2 Rated Voltage 100～1140 V ★ Y keyboard memory area4
Clear up keyboard memory area
b16 Motor 2 Pole Pairs 1～8 - 2 Y 5
1,2,3,4
rp 0：N action;
b17 Motor 2 Rated Speed 500～5000 1480 Y
m
1：Reset system parameter with keyboard memory area1;
b18 Motor 2 N Load Current 0.0～b14 A ★ Y 2：Reset system parameter with keyboard memory area2;
oh 3：Reset system parameter with keyboard memory area3;
b19 Motor 2 Stator Resistance 0.000～30.000 ★ Y
m
4：Reset system parameter with keyboard memory area4;
Motor 2 Rotator oh
b20 0.000～30.000 ★ Y 5：Clear up keyboard memory area 1,2,3,4
Resistance m
y02 Lastest Fault record Lastest fault record number - 0 Y
m
b21 Motor 2 Stator Inductance 0.0～3200.0 ★ Y
H y03 Fault Record 1
Motor 2 Mutual m y04 Fault Record 2 通过按下[PRG]和[▲/▼]键,
b22 0.0～3200.0 ★ Y
Inductance H Press [PRG]and [▲/▼] key the
y05 Fault Record 3 - - Y
The 2nd group motor parameters can be set by system. The difination is same with group 1. frequency, crrent and running status of
y06 Fault Record 4 fault time can be known.
y07 Fault Record 5
5-12 System parameter [SYS]
These parameters register fault which happen in the last several times, and can inquire about the value of
Upper group Next group
monitor object at the time of fault by ‘PRG’ and “plus or minus” key.
Description/LCD Set range Factory Modify
code unit
Keyboard diplay 7 segment LEDdisplay set limit The monitor object of fault state:
N action 0 0：Fault type
Reset system parameter with The fault code is expressed as following:
1
keyboard storage1 Serial LED display Fault message
Reset system parameter with number
2 0 E.OCP System is disturbed or impacted by instant over current
keyboard storage 2
Reset System
y00 Reset system parameter with - 0 N 1 E.OCC Over current signal from current inspected circuit.
Parameter 3
keyboard storage a3 2 E.OCF Over current or over voltage signal from drive circuit.
Reset system parameter with 3 E.OU Over voltage
4
keyboard storage 4
4 E.LU Under voltage
Reset system parameter with factory
5 5 E.OL Over load
set value
0：N action 6 E.UL Under load
1: Reset system parameter with keyboard storage 1 7 E.PHI Phase loss
2: Reset system parameter with keyboard storage 2 8 E.EEP EEPROM error
3: Reset system parameter with keyboard storage 3
9 E.ntC Over heat
4: Reset system parameter with keyboard storage 4
10 E.dAt Time limit fault
5：Reset system parameter with factory set value
When this parameter set valid,all the function parameter reset to factory setting. The parameters 11 E.Set External fault
without factory setting will save the previous setting value. 12 E.PId PID regulation fault

95 96
 Section V Parameter Function Table Section V Parameter Function Table

13 E.OHt Motor over heat fault code serial grade

14 E.OL2 Motor over load fault
15 E.PG PG error
product series (set according to family code/product serial/voltage grade)
80 0 3
16 E.PHo Inverter output phase-loss
17 E.COA Rs485 communication terminal A fault
family code series number input voltage level
18 E.COb Rs485 communication terminal B fault 80：8000 serial 1: single phase 220V
0: Flow load (F)
19 E.CAL Parameter indentification fault 81：8100 serial 1:General load (G) 2: three phase 220V
2: Middle load (M) 3: three phase 380V
1：set frequency at the time of fault 3: Heavy load (H) 4: three phase 460V
6: TEXDRIVE (S) 5: three phase 575V
The output frequency of the inverter at the time of fault 7: WINDLASS (T) 6: three phase 660V
2：output frequency at the time of fault 8:JETDRIVE (Z) 9: three phase 1140V

The output frequency of the inverter at the time of fault

3: output current at the time of fault y12 Software Version - - - N
The actual output current at the time of fault
A: official version
4: output DC voltage at the time of fault B:specialized version
The actual output voltage at the time of fault C:beta version version number
5: running state at the time of fault
The running state at the time of fault y13 Product Date-- Year YYYY - - N
Product Date －
y14 MMDD - - N
6：running time at the time of fault Month/Day
The running time at the time of fault 0～9999 Set range
7： Inverter IGBT temperature at the time of fault y15 User Decode Input Record password wrongly Display - - Y
Inverter IGBT temperature input times info
In the state of locked parameter, LED displays the times of error input. There are three input limit, if
LED display expresses the running state, and explains as following:
input is wrong in continuous three times, the systems will prohibit input of the password. It can prevent
The First Bit Of The Second Bit Of The Third Bit testing password in an illegal way, and need restart the machine to input again.
The Fourth Bit Of LED
LED LED Of LED Once the input is right in any time during three times input limit, the parameter is unlocked.
F forward F forward state A accelerating 0～9999 Set range
command
reverse N password or
R R forward state D decelerating
command compartmentatio y16 User password key-in decode input is deco - - Y
Display
running in a even correct
stop n code E info
S S stop state speed Parameter
command code
lock-in
S stop state
The parameter sets the password, and the range is 0~9999. After setting the password, parameter locks
N action 0 and keyboard displays “code”; if the password is unlocked or password input is right, the keyboard will
y08 Fault Record Reset - 0 Y
Reset 1 display “deco”.
0：N action, the fault records retains Set password to 0,reset user password set,after re-electrify status is decode。
1：the fault records resets Corresponding parameter group protection
Parameter Group after set password
y09 Rated Output Current 0.1～1000.0 A ★ N y17 - 0000 Y
Protection Set to 0: change is not allowed
Inverter rated output current. Set to 1: change is allowed
y10 Rated Input Voltage 100～1140 V ★ N
The rated input voltage of the inverter. It would be set as per inverter input voltage level before leaving
factory.
80 0 3
y11 Product Series - ★ N
Family Product Input voltage

97 98
 Section V Parameter Function Table Section VI Fault Diagnosis & Solutions
9 8 7 6 5 4 3 2 1 0
2 2 2 2 2 2 2 2 2 2 Section VI. Fault Diagnosis & Solutions
9 8 7 6 5 4 3 2 1 0

F group
A group 6-1 Problems and solutions
o group
H group Problems Possible causes Solutions
U group
P group
Keyboard Control mode setting is wrong Check F05
E group
C group can not
b group control Frequency setting is wrong Check F03、F04
y group
Potentiom Control mode setting is wrong Check F05
eter can’t
regulate Frequency setting is wrong Check F03、F04

LED monitor indicates error KeyRESET or terminal for fault reset, learn and fix
message the fault according to the fault info

N voltage in terminals DC+1

Check the voltage at R,S or T and charging circuit.
The and DC+2
motor
does Check the control mode and frequency parameter.
not U, V or W terminals produce N
Check the terminal condition if it is operated by an
rotate output or abnormal output.
external terminal.
Re-start after powering down
Remember the set operating state.
or free run

Check the load condtion, and confirm the model

Too much load on the motor
selection is right

Fault display E.OCP System is disturbed or instant over current

Fault display E.OCC OC signal from current self-inspected citcuit impact

Fault display E.OCF OC signal from drive circuit

Motor over current and current exceed 3 times of

Fault display E.OC3
motor’s rated current

Over Over current during Reset or modify the parameters of the

current acceleration functions F09,F20,F21
E.OC
Over current during Reset or modify the parameters of the functions
deceleration F10,F22,F23
During starting, the
low-frequency jitter Modify F06 setting
over-current
Over current during operation Check the load change and eliminate it.

Over current during starting or

Check if there is slight short circuit or grounding.
operation from time to time

99 100
 Section VI Fault Diagnosis & Solutions Section VI Fault Diagnosis & Solutions

Check the earthing wire, screened cable grounding the static electricity. If not, the components may be damaged.
Disturbance
and terminals.

Lower the load.or enlarge b04,b14 in the allowable

Too much load load range or enlarge A24 to raise the thermal

Over load protection level.

E.OL
Modify b04、b14 in case of the motor over-load
Inappropriate parameter is set
allowed

Check voltage is right or not.

Power voltage exceeds the
Frequency inverter rated voltage setting is right or
limit
not.
Over
voltage Too fast deceleration Modify F10.
E.OU
Reduce the load inertia, or raise the capacity of
The load has too much inertia
frequency converter, or add a braking resistor.

Checking voltage is normal or not.

Too low power voltage Frequency inverter rated voltage setting is right or
Low not.
voltage Add options of capacitor boxes.
E.LU Power off transiently

The line has too small capacity

or great rush current exists on Make renovation on power supply system.
the lines.

Too high ambient temperature Improve ambient conditions

Overheat
E.OHt Check A27,reduce fan starting tamperaturer(when
Cooling fans do not work.
there is fan control)

The carrier frequency is too

Check the setting value of function F16
high

Note:
※ Switch off the power supply, and do not touch the PCBs and any parts inside in five minutes after
the charging indicator light (！CHARGE) goes off. Ensure the capacitance has been discharged
completely by measuring with the instrument before work inside. Otherwise, there is a danger of
electric shock.
※ Do not touch the PCB or IGBT and other internal parts unless actions have been taken to prevent

101 102
 Section VII Standard Specifications Section VII Standard Specifications

Section VII Standard Specifications

7-1-2 PI8100 Specification
Light Load Standard Medium Heavy Load
7-1 Specification
F Load G Load M H Structu
Inverter type
7-1-1 PI8000 Specification PF IF PG IG PZ IZ PH IH re item
kW A kW A kW A kW A
Light Load Standard Load Medium Heavy Load
Single phase voltage 220V 50/60Hz
Inverter F G Load M H Structure PI8100●●●□1 0.75 4 0.4 2.5 7N3
type PF IF PG IG PM IM PH IH item
PI8100●●●□1 1.5 7 0.75 4 0.4 2.5 7N3
KW A KW A KW A KW A
PI8100●●●□1 1.5 7 0.75 4 0.4 2.5 7N3
3 phase voltage 380V 50/60Hz PI8100●●●□1 2.2 10 2.2 10 1.5 7 0.75 4 7N4
PI8000●●●□3 15 32 11 25 7.5 16 7.5 16 8N3 PI8100●●●□1 4 16 4 16 2.2 10 1.5 7 7N4
PI8000●●●□3 18.5 38 15 32 11 25 11 25 8N3 PI8100●●●□1 5.5 20 5.5 20 4 16 2.2 10 7N5
PI8000●●●□3 22 45 18.5 38 15 32 11 25 8N4 3 phase voltage 220V 50/60Hz
PI8000●●●□3 30 60 22 45 18.5 38 15 32 8N4 PI8100●●●□2 0.75 4 0.4 2.5 7N3
PI8000●●●□3 37 75 30 60 22 45 18.5 38 8N5 PI8100●●●□2 1.5 7 0.75 4 0.4 2.5 7N3
PI8000●●●□3 45 90 37 75 30 60 22 45 8N5 PI8100●●●□2 1.5 7 0.75 4 0.4 2.5 7N3
PI8000●●●□3 55 110 45 90 37 75 30 60 8N6 PI8100●●●□2 2.2 10 2.2 10 1.5 7 0.75 4 7N4
PI8000●●●□3 75 150 55 110 45 90 37 75 8N6 PI8100●●●□2 4 16 4 16 2.2 10 1.5 7 7N4
PI8000●●●□3 93 170 75 150 55 110 45 90 8N7 PI8100●●●□2 5.5 20 5.5 20 4 16 2.2 10 7N5
PI8000●●●□3 110 210 93 170 75 150 55 110 8N7 3 phase voltage 380V 50/60Hz
PI8000●●●□3 132 250 110 210 93 170 75 150 8N8 PI8100●●●□3 0.75 2.5 0.75 2.5 0.75 2.5 7N3
PI8000●●●□3 160 300 132 250 110 210 93 170 8N8 PI8100●●●□3 1.5 3.7 1.5 3.7 1.5 3.7 1.5 3.7 7N3
PI8000●●●□3 187 340 160 300 132 250 110 210 8NA PI8100●●●□3 2.2 5 2.2 5 2.2 5 2.2 5 7N3
PI8000●●●□3 200 380 187 340 160 300 132 250 8NA PI8100●●●□3 4 8.5 4 8.5 4 8.5 4 8.5 7N4
PI8000●●●□3 220 415 200 380 187 340 160 300 8NA PI8100●●●□3 5.5 13 5.5 13 5.5 13 7N4
PI8000●●●□3 250 470 220 415 8NA PI8100●●●□3 7.5 16 7.5 16 7.5 16 5.5 13 7N5
PI8000●●●□3 280 520 250 470 200 380 187 340 8NB PI8100●●●□3 11 25 7.5 16 7N5
PI8000●●●□3 315 600 280 520 220 415 200 380 8NB
PI8000●●●□3 355 640 315 600 250 470 220 415 8NB
PI8000●●●□3 400 750 355 640 280 520 250 470 8NB

103 104
 Section VII Standard Specifications Section VII Standard Specifications

7-2 Standard specification

7-1-3 Table of rated current for different specifications Items Specifications
Single-phase 200~240V,50/60Hz Three-phase
G/F/H/S/Z/T/M 200~240V,50/60Hz
220V 220V 380V 460V Three-phase 380~415V,50/60Hz Three-phase
Votage 575V 660V Voltage and
1Ф (240V) (415V) (440V) 440~460V,50/60Hz
frequency
Three-phase 575V,50/60Hz Three-phase
Power Current Current Current Current Current Current Power
660V,50/60Hz
(kW) (A) (A) (A) (A) (A) (A)
Three-phase 1140V,50/60H
0.4 2.5 2.5 - - - - Allowable
0.75 4 4 2.5 2.5 - - Fluctuation voltage: ±15% frequency: ±5%
range
1.5 7 7 3.7 3.7 - -
Control system high performance vector control inverter based on 32 bit DSP
2.2 10 10 5 5 - -
G/F/Z/S/T/M type：0.00～800.0Hz,maxmum frequency can
4 16 16 8.5 8 - - Output be set between 10.00 and 800.0Hz
5.5 - 20 13 11 - - frequency H type：0.00～2000.0Hz,maxmum frequency can be set
7.5 - 30 16 15 - - between 10.00 and 2000.0Hz
V/Fcontr Sensorless vector Sensor close loop
11 - 42 25 22 17 15 control method
ol control vector control
15 - 55 32 27 22 18 0.50Hz
Start torque 0.25Hz 180% 0.00Hz 180%
18.5 - 70 38 34 26 22 180%
speed
22 - 80 45 40 33 28
adjustable 1：100 1：200 1：2000
30 - 110 60 55 41 35 range
37 - 130 75 65 52 45 speed
stabilizing ±0.5% ±0.2% ±0.02%
45 - 160 90 80 62 52
precision
55 - 200 110 100 76 63 waveform Asynchronous space vector PWM, N-class sub-synchronous
75 - 260 150 130 104 86 produce space vector PWM, two-phase optimization of space vector
methods PWM.
93 - 320 170 147 117 98
Control Auto torque Achieve low frequency (1Hz) and high output torque control
110 - 380 210 180 145 121 boost function under V.F control mode.
132 - 420 250 216 173 150 Accelerate
Sub-set S curve acceleration and deceleration mode,
/decelerate
160 - 550 300 259 207 175 maximum acceleration and deceleration time is 3200 days
control
187 - 600 340 300 230 198 Long running
16 segments speed run, maximum running time is 3200 days
200 - 660 380 328 263 218 time control
frequency
220 - 720 415 358 287 240 Digit：0.01Hz(below 300Hz),0.1Hz(above 300Hz);
setting
alalogue： 1%of maxmum frequency
250 - - 470 400 325 270 accuracy
280 - - 520 449 360 330 frequency
Speed control tolerance 0.01%(25℃±10℃)。
accuracy
315 - - 600 516 415 345 V/F curve Linear, 1.2 times the power, 1.7 times the power, 2 times
355 - - 640 570 430 370 mode power, user-set 8 V / F Curve。
400 - - 690 650 520 430 G / S type: 150% rated current -1 minute, rated current 200%
-0.1 second;
500 - - 860 800 650 540 F-: rated current 120% -1 minute 150% of rated current of
Over load
-0.1 second;
capability
Z / M / T type: rated current 180% -1 minute 250% rated
current of -0.1 second;
H-: rated current 250% -1 minute 300% rated current -0.1
105 106
 Section VII Standard Specifications Section VII Standard Specifications

second. Double Supports dual-keyboard, synchronous control, independently

slip keyboard port of each other.
V / F control can automatically compensate for deterioration. Double and MF1, MF2 can be customized as addition and subtraction,
compensation
Running multi function forward, reverse, forward jog, and reverse jog, emergency
Keyboard/terminal/communication keys stop, rise and fall, and other 9 kinds of ways.
method
Forward, reverse, jog (parameter control direction), forward Control panel can be realized four groups of inverter
Starting signal 4-parameter
jog, and reverse jog. parameters of upload, download, with manufacturers
storages
Emergency password to reset factory setting.
Interrupt controller output. At most display 3 monitoring parameters. Select by A00, A01,
stop Running info
Running A02
When the protection function is active, you can automatically
fault reset Store 5 groups error messages at most, you can check the type
or manually reset the fault condition.
Motor status display, stop, acceleration and deceleration, of failure time when failure occurrs, set frequency, output
Running status Fault info
constant speed, the program running. frequency, output voltage, output current, running state,
Built-in PID regulator brake current flow in the premise, running time, IGBT temperature.
DC brake Double RS485 Rs485 port and an optional keyboard completely isolated
however, to ensure adequate braking torque.
Comminication port RS485 communication module.
Overvoltage protection, undervoltage protection, overcurrent
protection, overload protection, over-temperature protection, CAN BUS Can select can-bus module.
Inverter
over the loss of speed protection, over-voltage stall protection, 16-segment At most 16 segments can be set (use multi-functional terminal
protection
phase protection (optional), external fault, communication speed to shift or program runs).
error, PID feedback signal abnormalities, PG failure 8-segment At most 8 segment running time can be set (multi-functional
IGBT running time terminal can be used to shift)
temperature Display current IGBT temperature 8 segment
desplay At most 8 acceleration speed(can use the multi-functional
Speed acceleration
Protection Inverter fan terminal to switch).
The fan starting temperature can be set(optional) speed
control Seven-Segmen
Instant Less than 15 msec: continuous operation. At most 7 segment speed configuration can be set
t Speed
power-down Greater than 15 milliseconds: Automatic detection of motor (multi-functional terminal can be used to switch).
Configuration
re-start speed, instantaneous power-down re-start. PID feedback Six kinds of ways, keyboard, three way analog input, pulse
Speed starting signal input, digital potentiometers.
automatically track motor speed when inverter starts PID
track method PID giving Six kinds of ways, keyboard, three wayl analog input, pulse
Parameter signal input, digital potentiometers.
Protect inverter parameters by setting the password and
protection 2 goups of
decoding With the motor parameters , parameter can be selected,
function motor
Can be customized into 47 kinds of functions, to achieve parameter identification automatic storage.
parameters
8 way switch forward, reverse, forward jog, and reverse jog,emergency 3 identification Name plate calculation, static measurement, rotation
input stop, reset, speed, acceleration speed, run-time switch, and Motor method measurements.
pulse counting. 5 name plate Rated frequency, rated current, rated voltage, the number of
3 way analog Can be defined as a switch input; parameters pole pairs, rated speed.
IO
inputs To allow for maximum input range-10V ~ 10V, 0 ~ 20mA 5 indentification N-load current, stator resistance, rotor resistance, stator
2 way anolog parameters inductance, mutual inductance.
Can achieve output range 0 ~ 10V, 0 ~ 20mA
output Environment -10 ℃ ~ 40 ℃, 40 ~ 50 ℃ derating between the use is
Virtual temperature increased by 1 ℃, rated output current decrease of 1%。
Can be set to a virtual terminal, using communication or
terminal Store
keyboard IO port, and with the IO port status display. -40℃～+70℃
function temperature
In 6 main ways + to 7 kinds of auxiliary to the way of the Environment
Environment 5~ 95 % ,N condensation
Frequency set keyboard, three way analog input, pulse input, digital humidity
Keyboard potentiometers. Height·vibratio 0 ~ 2000 meters, 1000 meters above derating use, increased
Keyboard n by 100 m, rated input decreased%
8-core cable, in line with EIA T568A, EIA T568B standards.
cable
Application Mounted vertically inside the control cabinet with good

107 108
 Section VII Standard Specifications Section VII Standard Specifications

location ventilation, do not allow the level, or other installation

method. The cooling medium is air. Installed in the absence of
direct sunlight, N dust, N corrosive and explosive gas, N oil
7-3 Sharp Size
mist, N steam, N drip environment 7-3-1 PI8000 family (3 phase voltage 380～415V,50/60Hz）
Cooling 1. 8N2～8N7
Forced air cooling and natural air cooling.
method W
b H
d

DI GITAL PANEL
FWD REV ALARM

+ Hz
%
A ℃
s
- V

-
EN TE
+ R
PRG MF1 MF2 FWD

SET
ESC S TOP/RE SET

L
a
1) 8N2

Power Structu Shape Installation dimension

Type
(kW) re item L W H a b d
F 15~18.5
G 11~15
8N3 360 235 207 340 150 Ø10
M 7.5~11
H 7.5~11

2) 8N3
Power Structu Shape Installation dimension
Type
(kW) re item L W H a b d
F 22~30
G 18.5~22
8N4 410 264 242 390 165 Ø10
M 15~18.5
H 11~15

3) 8N4

109 110
 Section VII Standard Specifications Section VII Standard Specifications

Power Structu Shape Installation dimension

Type 2. 8NA
(kW) re item L W H a b d
F 37~45
G 30~37
8N5 560 300 243 540 200 Ø10
M 22~30
H 18.5~22

4) 8N5
Power Structur Shape Installation dimension
Type
(kW) e item L W H a b d
F 55~75
G 45~55
8N6 660 365 293 640 250 Ø10
M 37~45
H 30~37

5) 8N6
Power Structur Shape Installation dimension
Type
(kW) e item L W H a b d
F 93~110
G 75~93
8N7 710 455 293 690 350 Ø10
M 55~75
H 45~55

6) 8N7
Power Structur Shape Installation dimension
Type
(kW) e item L W H a b d
F 132~160
G 110~132
8N8 910 480 342 890 350 Ø10
M 93~110
H 75~93

111 112
 Section VII Standard Specifications Section VII Standard Specifications

Power Structur Shape Installation dimension

Type
(kW) e item L W H a b d
3. 8NB
F 187~250
G 160~220
8NA 1540 515 443 465 367 Ø13
M 132~187
H 110~160

L
W H
back entry
bottom board d
bottom entry

b
a

地板：bottom board
底部进线口：bottom entry

Power Structur Shape Installation dimension

Type
(kW) e item L W H a b d
F 280~400
G 250~355
8NB 1700 850 492 640 260 Ø13
M 200~280
H 187~250

113 114
 Section VII Standard Specifications Section VII Standard Specifications

7-3-2 PI8100 Family

2) 7N3
1. 7N2～7N4 Power
Power type type
(kW)
1) 7N2
F 2.2~4
Power
Power type type Single phase G 2.2~4
(kW)
220v M 1.5~2.2
F 0.75~1.5
H 0.75~1.5
Single phase G 0.4~1.5
F 2.2~4
220v M 0.4~0.75
3 phase G 2.2~4
H 0.4
220v M 1.5~2.2
F 0.75~1.5
H 0.75~1.5
3 phase G 0.4~1.5
F 4~5.5
220v M 0.4~0.75
3 phase G 4~5.5
H 0.4
380v M 4~5.5
F 1.5~2.2
H 4
3 phase G 0.75~2.2
380v M 0.75~2.2
H 0.75~2.2

DI GITAL P ANEL
FWD REV ALARM

+ Hz
%
A °C
s
- V

-
DIGIT AL P ANEL S00 Set Fre.

EN T
0.00 0.5
F WD R EV ALARM 1 Actual Fre.

ER
2 Motor AC

+
+ Hz
%
A °C
s
- V PR G
MF1 MF 2 FWD
-

S00 Se t F re.
E NT

0 .00 0.5 S ET
1 Act ual Fre . ESC STOP/RESET
ER

2 M oto r AC
+

PRG
MF1 MF2 FWD

SET
ESC STOP/ RESET

WARNING
Refer to the operation manual when adjust or inspect.
High voltage inside.Maintained by the well-trained
personnel.
Confirm the output or control Confirm the output or
control wires are not grounded.
Perform parts replacement after discharge.

W A RN IN G
Refer to the op eration m anual when adju st or inspect.
High voltage inside.Maintained by the well-trained
personnel.
Confirm the ou tpu t or control Confirm the output or
control wires are not grounded.
Perform parts replacem ent after discharge.
7N3 item: Plastic panel

7N2 item: Plastic panel

115 116
 Section VII Standard Specifications Section VII Standard Specifications

3) 7N5
Power DIGITAL PANEL
Power type type
(kW) FWD REV ALARM

+ Hz
%
A ℃

F 5.5 - V
s

-
Single phase G 5.5

ENT ER
220v

+
M 4
H 2.2 PRG MF1 MF2 FWD

F 5.5 SET ESC STOP/RESET

3 phase G 5.5
220v M 4
H 2.2
F 7.5~11
3 phase G 7.5
380v M 7.5
H 5.5~7.5

JP6E8000：

DIGITAL PANEL
FWD REV ALARM

+ Hz
%
A °C
s
- V

DIGITAL PANEL
-

S0 0 Set F re.
ENT

0 .0 0 0.5 FWD REV ALARM

1 A ctu al F re.
ER

2 Mo tor A C
+

+ Hz
%
A ℃
s
PR G
MF 1 M F2 FWD - V

-
SET
ESC S TO P /R E SE T

ENT ER
+
PRG MF1 MF2 FWD

SET ESC STOP/RESET

WAR NIN G
Re fer to the oper ation man ual w hen adjust or inspec t.
High vo ltage in side. Main taine d by the well-trained
pe rsonn el.
C o nfirm th e o utput o r c on trol C on firm the o utpu t or
c on trol w ire s are not gr oun de d.
Per for m parts r eplace me nt after discharge .

7N4 item: Plastic panel

7-3-3 Keyboard size

JP6D8000 the dimension of keyboard rabbet:
JP6C8000：

117 118
 Section VII Standard Specifications Section VIII Maintenance

Section VIII. Maintenance

8-1 Inspection and Maintenance

Under normal working conditions,in addition to daily inspection, the frequency
converter should be subject to regular inspection (for example inspection for overhaul or
as specified but at an interval of six months at most). Please refer to the following table
in order to prevent faults.
Check Check
time Check item Check to be done Method Criterion
D R point
LED and LCD If there is any As per use
√ Display Visual check
display abnormal display state
If abnormal noise or N abnormal
Cooling Visual and
√ √ Fan vibration is sound or
system audible check
the dimension of aperture for installing keyboard in panel： produced. vibration
（75.5±0.1）*（122.5±0.1） Temperature, Check visually,
Surrounding humidity, dust As per
√ Body by smelling and
conditions content, harmful gas, Section 2-1
feeling
etc.
Input/ Measure at
If input, output As per standard
第 √ output Voltage R, S, T and U, V,
voltage is abnormal specifications
terminal W terminals
八
章 If the fastenings
come loose, if any Check visually,
signs show overheat, tighten the
N abnormal
Overall conditions discharging, or too fastenings, and
conditions
high dust content, or clean the related
the air piping is parts
Main blocked
√ Electrolytic If there is abnormal N abnormal
circuit Check visually
capacitance appearance condition
Current-conductin If the parts come N abnormal
Check visually
g leads or blocks loose condition
If the screws or bolts Tighten the N abnormal
Terminals loose screws or
come loose condition
bolts
“D” means daily check and “R” means regularly check.
“√” means need daily check or regularly check
For inspection, do not disassemble or shake the parts without reason, and still less pull
off the plug-in-parts at random. Otherwise, the unit will not operate normally, or can not
enter the mode of fault display, or causes faults of components or even parts of the main
switch components IGBT module is damaged.
If measuring is necessary, the user should note that much different results will be gained
possibly if the measuring is performed with different instruments. It is recommended
that the input voltage be measured with pointer-type voltmeter, output voltage with
rectification voltmeter, input and output current with tong-test ammeter, and power with
electrically-driven wattmeter.

119 120
 Section VIII Maintenance Section IX Options

8-2. Periodically-Replaced Parts Section IX. Options

In order to ensure the operation reliability of the frequency converter, in addition to
regular maintenance and inspection, all the parts suffering long-term mechanical wear
should be replaced at a regular interval, which includes all cooling fans and the filtering The series can acquire the peripheral equipment by user because of the different
capacitors of main circuits for energy buffer and interchange and PCBs. For continuous using condition and requirement. See the wiring diagram as below:
use under normal conditions, these parts can be replaced according to the following
table and the operating environment, loads and the current state of frequency converter.

Part name Interval for replacement

Cooling fan 1~3 years
Filtering capacitor 4~5 years
PCB (printed circuit board) 5~8 years

8-3. Storage
The following actions must be taken if the frequency converter is not put into use
immediately after delivery to the user and need to keep well for the time being or stored
for a long time:
※ Stored in a dry and adequately-ventilated place without dust and metal powder at
the temperature specified in the specifications.
第 ※ If the frequency converter is not put into use after one year, a charge test should be
八 made, so as to resume the performance of the filtering capacitor of main circuit in
章 it. For charging, a voltage regulator should be used to slowly increase the input
voltage of the frequency converter until it reaches the rating, and the charge
should last more than 1~2 hours. This test should be made at least once a year.
※ Don’t perform breakdown test at random, for this test will cause shorter life of the
frequency converter. The insulation test must be performed after the insulation
resistance is measured with a 500-volt megaohm and this value must not be less
than 4MΩ.
8-4. Measuring and Judgment
※ If the current is measured with the general instrument, imbalance will exists for
the current at the input terminal. Generally, differing by not more than 10% is
normal. If it differs by 30%, inform the factory to replace the rectification bridge,
or check if the error of three-phase input voltage is above 5V.
※ If the three-phase output voltage is measured with a general multi-meter, the
reading is not accurate due to the interference of carrier frequency and only for
reference.

10-1.MCCB OR ELCB

As power switch of the inverter, MCCB or ELCB can protect supply power, but can’t

121 122
 Section IX Options Section IX Options

control inverter to run or stop. 45 230 175 150 10 160 110 23.0
55 230 175 160 10 160 120 23.0
10-2.AC reactance
AC reactance is able to restrain the high harmonic wave of converter input current and 75 285 220 230 14 180 130 30.0
improve converter’s power factor obviously. It’s recommended that AC reactance will 0.75 155 125 95 7 89 60 3.0
be used in the following condition:
1.5 155 125 95 7 89 60 3.0
※ The capacity of power source is ten times more than the capacity of converter. 2.2 155 125 95 7 89 60 3.0
※ SCR load or power factor compensated device with ON/OFF is connected with 4 155 125 95 7 89 60 3.5
the same power supply.
5.5 155 125 100 7 89 60 3.5
※ Unbalanced 3-phase voltage is bigger (more than 3%).
7.5 155 125 112 7 89 70 4.0
The common size of AC input reactance: 11 155 125 112 7 89 70 6.0
15 180 140 112 8 90 80 8.0
18.5 180 140 112 8 90 90 8.0

U V W 380V 22 180 140 112 8 90 90 8.0

460V 30 230 175 122 10 160 90 12.0
X Y Z
37 230 175 132 10 160 100 15.0
45 230 175 150 10 160 110 23.0
F 55 230 175 160 10 160 120 23.0
E
75 285 220 230 14 180 130 30.0
110 285 250 230 14 210 140 33.0

Sharp size: 160 360 260 230 14 210 140 40.0

200 360 270 230 14 210 140 45.0
Inverter standard Size (mm) Gross
Weight 250 400 330 240 14 240 140 55.0
Capacity
Voltage A B C D E F (kg) 315 400 350 285 14 270 160 90.0
(kW)
0.75 155 125 95 7 89 60 3.0 10-3. Noise filter
1.5 155 125 95 7 89 60 3.0 The filter is used to restrain the conduction of electrical magnetic wave interference
2.2 155 125 95 7 89 60 3.0
noise produced by the converter or shock the interferential form radio or momentary
concussion. The common size of 3-phase EMI noise filter is shown as following:
4 155 125 95 7 89 60 3.5 confirm the power supply is 3-phase three lines or 3-phase four lines or single phase.
5.5 155 125 100 7 89 60 3.5 Earthling wire is as short as possible, try to place the filter near the converter.
200V 7.5 155 125 112 7 89 70 4.0 Please choose EMI filter when the converter is used in residential area, commercial area,
230V 11 155 125 112 7 89 70 6.0 science area or other. Please need to prevent magnetic interference, or need meet CE,
UL, and CSA standard.
15 180 140 112 8 90 80 8.0
Note: If needing the filter, please connect with our company.
18.5 180 140 112 8 90 90 8.0
10-4. Connector
22 180 140 112 8 90 90 8.0 It can cut off the supply power in action of the system protection function, to prohibit
30 230 175 122 10 160 90 12.0 fault enlarging. But can’t control the motor start or stop by connector.
37 230 175 132 10 160 100 15.0 10-5. Braking Unit & braking resistor
There is braking unit inside when using “B” type frequency converter, the maximum
123 124
 Section IX Options Section X Quality Assurance

braking torque is 50%. Please choose braking resistor according to the following table: Section X Quality Assurance
Converter Braking resistor Braking resistor
Type power (Ω) Power (W)
(kW) The product quality assurance is in accordance with the following regulations:
0.75 200 120
1, The manufacturer should take responsibility for below specific elements:
1.5 100 300
1-1, in domestic use (as calculated from the date of shipment)
2.2 70 300
※ shipped within one month should accept refund, replacement and repair.
4 40 500
※ shipped within three months should accept replacement and repair.
5.5 30 500
220V ※ ship packages within 12 months should accept repair.
7.5 20 780 1-2, Goods exported overseas (excluding China) and shipped within six months, the
11 13.6 2000 local seller is responsible for repair.
15 10 3000 2, regardless of when and where to use POWTRAN branded products are paid to enjoy
18 8 4000 life-long service.
22 6.8 4500 3, all the distributors, agency or production place of POWTRAN in whole China can
0.75 750 120 provide after-sales service for powtarn product, their conditions of service as follows:
1.5 400 300 3-1, we provide a 3-level inspection service on the local selling place (including
2.2 250 300 troubleshooting).
4 150 500 3-2, all services comply with the related after-sale service terms and conditions stated
380V on the agency agreement between powtran and distributors.
5.5 100 500
7.5 75 780 3-3, buyers can pay to any Powtran agent if need any after-sales services (whether or
11 50 1000 not the warranty).
15 40 1500 4, if this product has some quality problem or product liability accidents, we will take
the responsibility to terms 1-1 or 1-2 at most. if users need more liability guarantee,
Please choose POWTRAN BRAKING UNIT if you need more braking torque. Please
refer to the catalog of braking unit. please apply for insurance company in advance to insure your own property insurance.
There is N braking unit inside the large capacity frequency converter. Please choose 5, the product’s warranty period is one year from the date of shipment.
POWTRAN BRAKING UNIT if you need braking. 6, in the case of the following causes of failure, even in the warranty period is also a
paid repair:
10-6.output EMI filter
The fittings can restrain the disturbance noise and lead leak current produced in the 6-1, incorrect operation (depending on the use of manual), or modified without
output side. permission to repair the problems caused.
6-2, the problems caused by using the inverters beyond its standard specifications
10-7.AC output reactor
requirement.
When the line from inverter to motor is longer than 20 meters, it can restrain the
over-current caused by the distributing current and the wireless disturbance of the 6-3, damage caused by drop down or improper handling.
inverter. 6-4, inverters components aged or failure caused by improper environment.
6-5, due to an earthquake, fire, wind and water disasters, lightning, abnormal voltage or
other natural disasters and disasters, accompanied by the damage caused.
6-6, the damage during transport (Note: The mode of transport designated by the
customer, the company's help on behalf of the procedures for handling the transfer of
goods).
6-7, when the manufacture’s brand, trademark, serial number, nameplate and other
damage or can not be recognized.
6-8, if the buyer has not paid full money according to purchase agreement.
6-9, the installation, wiring, operation, maintenance or other use of objective reality can

125
 Section X Quality Assurance Appendix I RS485 Communication Protocol

not be described to the company's service office. Appendix 1. RS485 communication protocol
7, concerning refund, replacement and repair services, goods shall be returned powtran
company, after confirmed the attribution of responsibility then they are allowed to be
1. Use introduce
returned or repaired.
This chapter introduces something about the install and handle of RS485
communication between inverter and PLC, PC, factory computer.
RS485 standard interface
l Can communicate with all computer
l Using multi-drop link system, can link more to 127 inverters
l Completely isolated, and noise shield
l The user would use all types of RS232-485 inverter, if only the inverter had
“automatic RTS control” function inside.
2 Specification
Communication function
Items Specification
Communication baud
38400/19200/9600/4800/2400/1200 bps is selectable.
rate
Communication
Modbus protocal,RTU fomat
Protocol

Interface methods
t
Asynchronism communication methods, semi-duplex, he previous high byte,
low byte in the post, and low-effective-bit pre-emptive.
1 start bit, 8 data bits, 1 stop bit, N parity bit.
1 start bit, 8 data bits, 1 stop bit, even parity bit.
1 start bit, 8 data bits, 1 stop bit, odd parity bit.
Data fumula
1 start bit, 8 data bits, 2 stop bit, N parity bit.
1 start bit, 8 data bits, 2 stop bit, even parity bit.
1 start bit, 8 data bits, 2 stop bit, odd parity bit.
Slave addresses can be set up 1~ 127
Slave address
0 for broadcast address, host address 128 for the proportion of linkage
Communication
Terminals SG+,SG-,shield SH,Default 19200bps.
connect A
Communication
RJ45,8-core shielded cable, fixed 19200bps, N parity bit
connect B

3. Communication connection
Definition for Communication port A:
l Link RS485 communication cables to inverter control terminals (SG+), (SG-).
l When using RS232-485 transform, connect Inverter “SG+” to RS485
“T+”,Inverter “SG-” to RS485 “T-”.

127 128
 Appendix I RS485 Communication Protocol Appendix I RS485 Communication Protocol

l After Confirming connection again, turn on inverter power. l The number of inverter can be connected is N more than 127.
l If connection is right, set communication parameters as following: l Though the length of communication cable can add up to 1300m, considering the
stability, the length limit within 800m.
l A26 baud rate 0：1200,1：2400,2：4800,3：9600,4：19200,5：38400
l All the control signal cable use the screen cable, and is linked to the signal terminal
l A27 current inverter communication address 1~127 (If there are more than 1 “SH” of RS485.
inverters, don’t use the same number); l Data packet using CRC (vertical lengthy test) frame detection to ensure data
l When using RS485 running control methods, set F05=0/1/2(Keypad + reliability.
RS485/CAN) l completely isolated RS485 communication module to ensure reliable
communications, support hot-swappable, after modular access, you can enter the
Match register
work.
TX
120ohm 1/4W l the system is tested in 6 kinds of baud rate: 0:1200,1:2400,2:4800,3:9600,
RX RS485 T+
GND converter T-
4:19200,5:38400
However, if under deteriorating environmental conditions, lowering the baud rate
SG- SG+ SG- SG+ SG- SG+ can improve the communication quality.
1# 2#
……
N# l Interval time of sending from frame to frame is more than 50ms.
PC
Inverter Inverter Inverter

4 Communication Protocol
Definition for Communication port B： Communication architecture is inverter as a slave, the computer as a host.

Communication port 1 2 3 4 5 6 7 8 The basic format description

B pins
1: start of frame
Communication B port GND +5V 485+ 485- 485+ 485- +5V GND Interval> 2ms,
signal 2: Slave Address
EIA/TIA T568A White White blue white orange White brown From the machine's local address, through the A27 parameter settings, can only
green green orange Blue Brown
have that uniquely identifies a network's local address.
EIA/TIA T568B White Orange Blue White green White brown Setting Range 1 ~ 127.
Orange White Blue Brown 00H = 0 ID address is broadcast mailing address, 128 ~ 255 reserved.
Gree 3: Function Code
n Host to send commands from the machine to the command response.
l Function Code Categories
0x02＝read slave fault record
Frame start address Slave adress Function code Registers address CRC checksum frame end address

Interval> 2ms idle bit 1 bytes 1 bytes 2 bytes 2 bytes Interval> 2ms idle bit

Slave response
Frame start address Slave adress Function code Registers address CRC checksum frame end address

Interval> 2ms idle bit 1 bytes 1 bytes 2 bytes 2 bytes Interval> 2ms idle bit

0x03＝read single register

Host command
Data safety and reliability

129 130
 Appendix I RS485 Communication Protocol Appendix I RS485 Communication Protocol

Frame start address Slave adress Function code Registers N. CRC checksum frame end adress
Frame start address Slave adress Function code Registers address CRC checksum frame end adress
Interval> 2ms idle bit 1 bytes 1 bytes 1 bytes 2 bytes Interval> 2ms idle bit
Interval> 2ms idle bit 1 bytes 1 bytes 2 bytes 2 bytes Interval> 2ms idle bit

Slave response
Frame start address Slave adress Function code Registers address CRC checksum frame end adress
If slave response and get back to below function code, it means communications
abnormal.
Interval> 2ms idle bit 1 bytes 1 bytes 2 bytes 2 bytes Interval> 2ms idle bit
0xA0 = Invalid operation, setting under this state is invalid
0xA1 = function code is invalid
0x13＝Read multiple registers
0xA2 = Fault record is empty
Host command
0xA3 = register address is invalid
Slave Function Register Register … Register add. CRC
Frame start address frame end adress 0xA4 = slave is busy, EEPROM delay.
adress code N. add.1 n. checksum
0xA5 = administrator restricted
Interval> 2ms idle 1 bytes … Interval> 2ms idle
1 bytes 1 bytes 2 bytes 2 bytes 2 bytes 0xA6 = set value is beyond limit.
bit bit
0xA7 = CRC checksum error
0xA8 = frame format error
Slave response
Slave Function Register Register data … Register data CRC
Frame start address frame end adress
adress code N. 1 n. checksum
4: Register Address:
Interval> 2ms idle 1 bytes … Interval> 2ms idle
the register address includes two bytes, data setting is constituted by a two-byte.
1 bytes 1 bytes 2 bytes 2 bytes 2 bytes Function code Register Address high byte Register Address low byte
bit bit
Parameter group Parameter serial number
F 0x00 0～63
0x06 = write to slave a single register (power-down does not save)
A 0x01 0～63
0x26 = write to slave a single register (power-down save)
o 0x02 0～71
Host Command
H 0x03 0～55
Frame start address Slave adress Function code Register address Register data CRC checksum frame end adress
U 0x04 0～15
Interval> 2ms idle bit 1 bytes 1 bytes 2 bytes 2 bytes 2 bytes Interval> 2ms idle bit
P 0x05 0～15
Slave response 0x03/0x13 E 0x06 0～23
Frame start address Slave adress Function code Register address Register data CRC checksum frame end adress
（read slave
C 0x07 0～47
function code
Interval> 2ms idle bit 1 bytes 1 bytes 1 bytes 2 bytes 2 bytes… Interval> 2ms idle bit b 0x08 0～23
parameter）
y 0x09 0～23
L 0x0A 0～31
0x16 = Write multiple registers to the slave (power-down does not save) S 0x0B 0～15
NOTE 2
0x36 = Write multiple registers to the slave (power-down save) 0x00 Running status
Host Command 0x01 Reserved status 1
R 0x10
Frame Register Register … Register Register 0x02 Reserved status 2
Slave Function Register CRC frame end
start N. data 1 add. n data n 0x03 Reserved status 3
adress code add.1 checksum adress High byte
address 0x06/0x16（set Parameter group Low byte data
data
Interval> 1 bytes … Interval> slave function
1 code parameter F 0x00 0～63
2ms idle 1 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2ms idle
bytes and write A 0x01 0～63
bit bit
RAM） o 0x02 0～71
H 0x03 0～55
Response command U 0x04 0～15

131 132
 Appendix I RS485 Communication Protocol Appendix I RS485 Communication Protocol

0x26/0x36（set P 0x05 0～15 y13 product date –year Valid operation Invalid operation
slave function y14 product
E 0x06 0～23 Valid operation Invalid operation
code parameter month–date
C 0x07 0～47
and write y15 user decode Valid operation Invalid operation
b 0x08 0～23
EEPROM） y16 user input
y 0x09 0～23 Valid operation Valid operation
password
L 0x0A 0～31 y17 parameter group
NOTE 3 Valid operation Valid operation
0x00 Running command protection
0x01 Reserved status 1
R 0x10
0x02 Reserved status 2
0x03 Reserved status 3 NOTE 2：
Fault record data Fault inquiry content data BIT 15 BIT 14 BIT 13 BIT 12 BIT
Faulty typeNOTE 4 0x00 0：N fault
0：N fault 0：N fault 0：confirmed fault
Fault history record 1 Set frequency 0x01 meaning 1：urgent stopping
1：decelerating fault 1：alarming fault 1：unconfirmed fault
Fault history record 2 0x00 fault
0x02 Actual frequency 0x02
Fault history record 3 0x01 bit 11 BIT 10 BIT、 9 BIT 8 BIT
（read the Actual current 0x03
Fault history record 4 0x02 0：N JOG.
fault record） Dc voltage 0x04 meanning reserved reserved reserved
Fault history record 5 0x03 1：JOG running
0x04 Running status NOTE 2 0x05
bit 7 BIT 6 BIT 5 BIT 、 4 BIT
Running time 0x06
0：lower frequency 0：upper frequency
IGBT temperature 0x07 00：stopping 01：accelerating
not arriving not arriving
meaning 10：decelerating
1：arrive lower 1：arrive upperer
11：running in a even speed
frequency frequency
NOTE 1： bit 3 BIT 2 BIT 1 BIT 0 BIT
0x06/0x16 writing operation 0：running reverse 0: V/F control
Function 0x03/0x13 reading operation meaning reserve reserve
0x26/0x36 reading operation 1：running forward 1：SV control
y00 reset the factory
Return 0 Only can write into 5
setting
y01 upload parameter
Return 0 Invalid operation
onto keyboad
y02 latest fault record Valid operation Invalid operation
Empty
00H
record
y03～y07
New record 01H Invalid operation
fault history record
Confirmed
02H
record
y08
Return 0 Valid operation
reset fault record
y09 rated output
Valid operation Invalid operation
current
y10 rated output
Valid operation Invalid operation
voltage
80 0 3
Family Function Input voltage
y11 products series Invalid operation
serial code level
The number should be decimalization.
y12 soft ware version Valid operation Invalid operation

133 134
 Appendix I RS485 Communication Protocol Appendix I RS485 Communication Protocol

NOTE 3： 5：CRC checkup sum

bit 15 BIT 14 BIT 13 BIT 12 BIT Data meaning：data frame CRC checkup sum,using 2 bytes.
Checkup sum ＝all the CRC checkup sum in one data frame.
meaning reserve reserve reserve reserve

Bit 11 BIT 10 BIT 9 BIT 8 BIT Valid setup and communications under normal circumstances, the host command and
slave responses are as follows:
meaning reserve reserve reserve reserve

bit 7 BIT 6 BIT 5 BIT 4 BIT Host Command

0：N free-stop Host Registers CRC
0：JOG stopping
meaning 1:free-stop reserve reserve Slave Setting
1：JOG running Frame start address command address checkup
command address data
code sum
bit 3 BIT 2 BIT 1 BIT 0 BIT
0:reverse command Interval> 2ms idle bit 0x08 0x06 0x0001 0x1388 0xD5C5
0:stop command
meaning reserve 1:forward reserve
1:run command
command Slave response
NOTE 4： fault style code Registers CRC
Slave Host response Setting
Serial Frame start address address checkup
LED display Fault message address code data
nmber sum
nnnnumber Interval> 2ms idle bit 0x08 0x06 0x0001 0x1388 0xD5C5
0 E.OCP IGBT power driver protect and produce hardware interrupt.
1 E.OCC OC signal from current self-inspected circuit impact.
2 E.OCF OC signal from drive circuit.
3 E.OU Over voltage
4 E.LU Lower voltage 5 Example of communication protocol:
5 E.OL Over load unsigned int cal_crc16 (unsigned char *data, unsigned int length)
6 E.UL Lower load
{
7 E.PHI Input phase lose
unsigned int i,crc_result=0xffff;
8 E.EEP EEPROM error
while(length--)
9 E.ntC Over heat
10 E.dAt Time limit fault {

11 E.Set External fault crc_result^=*data++;

12 E.PId PID regulation fault for(i=0;i<8;i++)
13 E.OHt Motor over heat fault
{
14 E.OL2 Motor over load falult
if(crc_result&0x01)
15 E.PG PG error
16 E.PHo Output phase lose crc_result=(crc_result>>1)^0xa001;

17 E.COA Rs485 communication connect A fault else

18 E.COb Rs485 communication connect B fault crc_result=crc_result>>1;
19 E.CAL Parameter Identification Failure }

crc_result=((crc_result&0xff)<<8)|(crc_result>>8);
135 136
 Appendix I RS485 Communication Protocol Appendix II Instruction Of The Proportional Linkage Function

return(crc_result); Appendix 2: Instruction of the proportional linkage function

1. proportional linkage function：

The proportion interaction host computer:
communication address = 128,
communications port A is the communication port of host computer.
附 Communication port B can be used as the keyboard interface, or a PC host computer interface.
录 There is only one host inverter in one proportional linkage.
2
The host inverter control the running state, the slave inverter follow the host’s running state.
Communication Address = 1 ~ 127,
Both communication port A and communication port B can be the communication port of slave
inverter.
the slave inverter follow the host running and it can realize forced stopping by terminal or keyboard
if need.
For this function, the host computer should be set with the following parameters:

A28 Local communication address 128

For this function, the slave computer should be set with the following parameters:

Keyboard set the frequency /

F01 Command from proportion linkage Host
Rs485
Keyboard setting frequency or
0
RS485
AI1 the external analog setting 1
AI2 the external analog setting 2
F02 Frequency main set mode AI3 the external analog setting 3
Keyboard potentiometer setting 4
Multi-segment digital voltage set 5
Digital Pulse Setting 6
Keyboard setting frequency or
0
RS485
AI1 the external analog setting 1
AI2 the external analog setting 2
Auxiliary setting mode of AI3 the external analog setting 3
F03
frequency set Keyboard potentiometer setting 4
Multi-segment digital voltage
5
setting
Digital Pulse Set 6
PID regulation mode 7
The main setting individual control 0
relationship between main and
F04 The auxiliary setting individual
auxiliary frequencies 1
control

137
 Appendix V Converter Water Supply Controller Instruction Appendix II Instruction Of The Proportional Linkage Function

main + auxiliary 2
o37 DI2 input terminal function 2:reverse running
main -auxiliary 3
（main *auxiliary）/maximum The proportional linkage slave settings:
4
frequency
Maximum｛main ,auxiliary｝ 5
F02 Frequency main set keyboard set the frequency or Rs485 0
Minimum｛main ,auxiliary｝ 6
F05 Running control mode Proportional linkage control 4 Auxiliary setting mode of
F03 AI1 external analog setting 1
Select this function, the slave inverter will follow the command of host inverter to frequency set
run. after select this function, it can also use keyboard, terminal and RS485 to control
relationship between main and
the slave inverter’s running. F04 main＋Auxiliary 2
auxiliary frequencies
In the proportion of linkage during operation, if control by the keyboard, terminal,
RS485 control, once the slave inverter stopped, the slave will N longer respond to the F05 Running control mode Proportional linkage control 4

host command, if need the slave once again to respond to host commands , it should A28 Communication address 1～127
control through the keyboard, terminal and RS485, or after the host sends cease and A29 Baud rate Same as host inverter
desist commands then the slave will respond the command again to run.
A30 Communication format Same as host inverter
A28 communication address 1～127
o36 DI1 input terminal function 37:forced stopping
A29 Baud rate Same as host
o37 DI2 input terminal function 38:Up command
A30 Communication format Same as host
o38 DI3 input terminal function 39:Down command
A55 Proportional linkage factor 0.10～10.00
A43 Multi-function key MF1 8:MF key is appointed to be Up command
o20/2
A44
A44 9:MFkey is appointed to be Down
Multi-function key MF2
During the proportional of linkage, the running state of slave inverter is controlled by the host A44 command
inverter. 0
o01 电压 of host inverter of proportion linkage System wire connections:
Slave inverter F01 = proportional factor ×the actualo02
(o01+o02)/2 set frequency
Slaver S00 actual set frequency = slave F01 + frequency give and secondary amend +ascend/descend
-o20/2
adjusting

2. Proportion linkage application Cases:

Features of proportional function:
1:the host inverter using the potentiometer to control the system speed and use the terminals to
control the forward/reverse running.
2: the slave follows the host running, the proportional linkage factor is 1.00
3:after get the running speed command from host inverter, the slave will store this command into to
F01.
4: the slave actual frequency is set through the keyboard or through terminal ascend/descend
adjusting.
5: the slave actual frequency is set through potentiometer adjusting.
6: the slave actual frequency = F01 + slave potentiometer adjusting + A40

The proportional linkage host settings:

F02 Frequency main set mode AI1 external analog setting
A28 Communication address Host 128
A29 Baud rate 3：9600bps
A30 Communication format 0
o36 DI1 input terminal function 1:forward running

139 140
Appendix V Converter Water Supply Controller Instruction

141
Appendix III PG Instruction

Appendix 3. PG instruction

1. PI8000 PG.V1 can use for 5V line-driven encoder.

2. terminal function instruction
Terminals functions
A+ A- , B+ B- , Z+ Z- Encoder signal input
+5V Encoder power supply,5V
GND Encoder earthing

Terminal connections:
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction

Appendix 4 Converter water supply controller instruction safe and reliable.

When Feedback voltage is 100% , the corresponding Hall voltage is 500VAC, Hall output voltage
is 5V.
E00 function parameter setting definition set o03=50%,o05=50%。
P03 PID given signal selection,you can set through the keyboard, analog AI1, pulse and other
8 inverter power means to set a given voltage.
special power supply 13 stable voltage power given voltage is calculates as follows:
14 constant current power When the given voltage =220VAC,given voltage setting =220×1.414/500*100%=62.2%
1 pump Other PID parameters are adjusted according to the site.
Under PID regulated power supply mode, the voltage acceleration and deceleration time is
constant pressure water supply double pump constant controlled by PID parameters, it won’t affect by voltage acceleration and deceleration time.
9
pressure water supply

A. Extend functions supplement Voltage regulation power specific parameters:

1、E00 loading type: N. name Range unit Description Factory setting
(1)、E00=8：variable frequency power User
E16 0～9999 - Voltage increasing time 0
P03 PID given signal selection,you can set through the keyboard, analog AI1, pulse and other parameter 1
means to set a given voltage. User 0～9999
Given voltage is calculated as follows:： E17 - Voltage decreasing time 0
parameter 2
Given voltage:220VAC In Voltage regulation power mode, the output and input voltage are both adjustable.
Given voltage setting =220×1.414/500*100%=62.2% The increasing time and decreasing time of output voltage is adjusted by F09 and F10.
E16 is the voltage increasing time, the definition of the output voltage increasing time is from
Frequency Power specific parameters: 9999 corresponds to 999.9 seconds.
N. name scope unit meanings Factory setting E17 is the voltage decreasing time, the definition of the output voltage decreasing time is from
E16 User parameter 1 0～9999 - Voltage increasing time 0 9999 corresponds to 999.9 seconds.
E17 User parameter 2 0～9999 - Voltage decreasing time 0 Voltage increasing/decreasing time just used to adjust the accelerate/decelerate time of output
frequency when the inverter running.
In regulated power supply mode, the output and input voltage are both adjustable. After the stopping command sent, the controller will stop the frequency output when the output
The increasing time and decreasing time of output voltage is adjusted by F09 and F10. frequency decelerate to 0hz.
E16 is the voltage increasing time, the definition of the output voltage increasing time is from
9999 corresponds to 999.9 seconds. User 0～9999
E18 - Max output voltage 0
E17 is the voltage decreasing time, the definition of the output voltage decreasing time is from parameter 3
9999 corresponds to 999.9 seconds. For safety and reliability to ensure that the output voltage to bear the load within the system, we
Voltage increasing/decreasing time just used to adjust the accelerate/decelerate time of output need to define the maximum output voltage.
frequency when the inverter running.
If the system highest voltage 250VAC.
After the stopping command issued, the controller will stop the frequency output when the output
frequency decelerate to 0hz. Then a maximum output voltage = =250×1.414/500*100%=70.7%
User 0～9999 E18=707
E18 - The max output voltage 0 2、E02 Starting delay time
parameter 3
For safety and reliability to ensure that the output voltage to bear the load within the system, we Feedback pressure <given pressure –starting pressure deviation
need to define the maximum output voltage. Continuously exceed E02 start delay time,the inverter will restart under in the standby mode. This
If the system highest withstand voltage 250VAC. parameter is used to prevent the inverter frequent start-stop.
Then a maximum output voltage = 250
E18=250 3、E04 Stop delay time
If you set the frequency less than or equal shutdown frequency and exceed E04 shutdown delay
(2)、E00=13：Voltage regulation power time, the inverter will change from running state into the stop and standby state.
The parameter set bigger, the inverter will be easier to stop. This parameter set to 0 it means the
In this mode, connect AI2,AI3 to Hall,then measure the output voltage and use 2 Halls to do
stop frequency and start-stop pressure control are invalid.
redundant work to ensure the output voltage will not exceed the Hall voltage limitation.
E01, E02, E03, E04 parameter group are used to control system energy-saving operation and
In this mode, the following parameters should be adjusted:
control water pressure regulation in water supply systems.
PID function group,P02 PID feedback signal selection.
For example:
AI2 is detected by analog and AI3 works as a redundant configuration to ensure the output voltage
143 144
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction
given pressure = 50%
Starting pressure deviation =10%, starting pressure = given pressure - starting pressure deviation =
40% Thousand digit：the current regular time
stopping frequency= 5Hz When the water supply time set 0, it means cancel the water supply time setting of this period.
Current tim e Water supply time Pressure given
0 H18 H47
1 H19 H48
pressure
feedback pressure 2 H20 H49
set pressure 3 H21 H50
50％
4 H22 H51
start pressure 5 H23 H52
10％
6 H24 H53
0
H07
time 7 H25 H54
frequency
actual frequency
upper frequency
7, E08 Timing shif alternation time
Timing shif alternation time can control the pump’s rotation mode and time.
stop pressure
When the timing shif alternation time is set to 0.0 hours, it means cancel timing rotation function.
lower frequency
0 When the timing shif alternation time set between 0.1 to 3200.0, then after a stable operation for
H08 time a while, it will control the pump rotation at the principle of first start and first stop.
First start and first stop: if want stop some pumps, should firstly stop the first starting pump.
4, E05 High pressure arrival value
When feedback pressure reach and exceed the high pressure reached value of this parameter, the I According first stop and first start principle to add or reduce pumps can help to ensure each pump
/ O output terminal select 25, then it will output arrival signal. has chance to run which can protect some pumps from being rust due to non-run for a long time. If user
need keep each pump run at a average time, then just need set the timing shif alternation time
5、E06 low pressure reached value Order of adding pumps : pump 1→pump 2→pump 3→4
When feedback pressure less than the low pressure reached value of this parameter, the I / O
output terminal select 26, then it will output arrival signal. Order of reducing pups: pump 4→pump 3→pump 2→pump 1
Same as currently： pump 1 at working frequency, pump 2 at working frequency, pump 3 at
6、E07Low pressure arribal value variable frequency
Bit：Timing water supply reduce pumps：pump 1 at working frequency, pump 2 at variable frequency.
0 Timing water supply function is invalid then add pumps：pump 1 at working frequency, pump 2 at working frequency,4# pump at variable
1 Timing water supply function is valid frequency.
Tens digit：pressure giving reduce pump: pump 1 at working frequency , pump 2 at variable frequency.
0 :the pressure given during regular pressure water supply is set according PID given value reduce pump：pump 1 at variable frequency
selecting P03.
add pump ：pump 1 at working frequency,pump 3 at variable frequency.
1 the pressure given during regular pressure water supply is set according the current
add pump：pump 1 at industry frequency,pump 3 at industry frequency,pump 4 at variable
corresponding H47~H54 digital voltage given.
frequency.
hundred digital：timing mode
Add pump：pump 1 at industry frequency , pump 3 at industry frequency,pump 4 at industry
0 cycle mode
frequency, pump 2 at variable frequency.
Start to time from start running , after it reached the setting time, the inverter will automatically
move to the next period of time set, after the end of a loop, it will automatically re-start from the first
8、E09 Electromagnetic switch action delay
paragraph 0, then cycle to run. Electromagnetic switch action delay time when set up a pump (drive motor) to switch from
1 single cycle variable frequency to industry frequency ,or from industry frequency to variable frequency.This is to
Start to time from start running, after it reached the setting time, the inverter will automatically avoid inverter output frequency meet with the AC power supply and occur short circuit caused because
move to the next period of time set, after the end of a loop, the inverter will stop and wait for the next electromagnetic switch action too slow.
running command.
9, E10 Pumps shift judging time
145 146
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction
To set the determine time from inverter output frequency reaches the upper frequency until
increase pump (drive motor); or from inverter output frequency reaches the lower frequency until
decrease pump (drive motor).Time setting is based on the pressure change speed, if it is within the
scope of N oscillation occurred, the time set i is the shorter the better. B.Converter water supply controller instruction
inverter will control E12 constant pressure water supply pump.
1. Application
10、E11 Constant pressure water supply configuration It is special appendix for multiple pumps, which run with PI7000 family inverter
Bit ：Stop mode to control the multiple pumps water supply system effectively.
0 Decelerating stop: When the inverter fails, all the pumps in turn stop. 2. Operation and connection notice:
1 variable- frequency stop: When the inverter failure, the variable frequency pumps stop running,
◇ If it is power frequency motor, probable thermal relay must be used to protect
the industry frequency working pumps keep running.
motor.
Stop industry-frequency working pump, need to use the o36 ~ o46 input terminals of free stop
commands or multi-function keys MF1, MF2 of keyboard is set to 2: free parking function. ◇ AC contactor with machinery chain equipment should be used between the
2 Free stop: When the inverter fails, all the pumps free stop. power frequency bypass and inverter output of aside the motor, lock logically on
tens bit : Pumps status when fault occurs the electri control circuit to avoid the short circuit of the power frequency and
0 maintaining the status : when inverter fault occurs, stop the current pump, the other pump to inverter output which damage the inverter and equipments.
maintain the current status. ◇ The phase order of the power frequency to the motor should be the same with
1. all pumps stop: When the inverter fails, all the pumps free stop. the phase order of the inverter output to avoid the motor reverse. Please confirm
Hundred bit : Alternation shift mode the phase order and operate.
0 Variable frequency to industry frequency: when increase the frequency-controlled pump to the ◇ When wiring the control signal of the inverter, please leave it away with the
industry frequency then it will perform rotational switch or soft starter control. driving line, and do not make them in the same wire, otherwise it will lead
1- Variable frequency to stop: after the current variable frequency-controlled pump stopped, it will wrong action.
perform rotational switch or soft starter control.
◇ Screen cable is used for Pressure set signal and pressure feedback signal.
Thousand bit : Pump maintain the status
0 keep status: after multi-pump constant pressure water supply shut down ,maintain all pumps in 3. Dimension
the current order of first starter first stop.
3.1 Dimension of water supply control card
1.stop Reset: Multi-pump constant pressure water supply stoop, according to E12 multi-pump
configuration to re-sort the order of first start first stop.

147 148
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction

fixed plate

fixed plate fixed plate

3.2 Dimension of water supply controller

the size of fixed plate

Note: The fixed plate can be fixed by any mounting hole in the figure.

4 Connection of water supply controller with inverter

4.1 Istall RS485 on the control card, the installation of the RS485 is showed
below:
7K-RS485_S with 8KLCB

149 150
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction

7K-RS485 With 8KSCB

4.2 Connection of water supply controller with inverter, the communniction

cable and power cable are connected as below:

151 152
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction

System diagram
Soft-start pump terminal control, stop first.
Soft-start pump is not controlled by constant pressure water supply system.
Soft-start pump can be used as sewage pumps and fire pumps.

7. Constant water supply system parameters:

(1) loading types with constant water supply function：
param
Keyboard display setting Meanings
eter
Starting pressure Single Pump constant pressure water supply, N need
E00 1
deviation the constant pressure water supply interface board.
Multi-pump constant pressure water supply, need
Starting pressure
E00 9 constant pressure water supply interface board, while
deviation
realize 4- pumps constant pressure water supply

(2) PID adjusting in constant water supply system

Keyboard
Parameter Setting Meanings
Display
Keyboard set
F01 0 Keyboard set the frequency 0hz
frequency
Frequency main
F02 0 Keyboard set frequency or RS485 set frequency.
set mode
Frequency
F03 auxiliary set 7 PID adjusting mode
Remarks: ZK air switch KM contactor mode
JR thermo-relay M motor main and
F04 auxiliary 2 main+ auxiliary set mode
frequencies set
5.Water supply control mode P00 0000 single-way, the negative regulator, failure is not action
PID configure
When several pumps supply water meanwhile, because of the different
Feedback signal External analog feedback signal given by the
time(daytime and night), different season(winter and summer), the variation of the P02
select
1～3
AI1/AI2/AI3
water flow is great. To save energy and protect the equipment, please run pumps as
Given signal Given signal can select the keyboard / Rs485,
many as you need and stop pumps as many as you do not need. P03 0～6
select potentiometers, digital voltage, digital pulse, etc.
Inverter will confirm the number of the running pumps according to the PID integration
requirement of the pressure close loop control. In the set range, only one pump is P05 time ★ Setting according the site.
controlled by the inverter at the same time.
If the timing shift interval time is set 0.05~100.00, when the related running time PID differential Setting according the site.
is stable, inverter inverter will shift up the pumps according to stop first or open first P06 ★
time
to ensure each pump has the chance to run and avoid the pump rusted because of long PID proportional Setting according the site.
time N use. P07 ★
gain
After the pumps run to the upper and lower, arrive the adding pumps or reducing P09 Deviation Limit ★ Setting according the site.
pumps time, inverter will add or redcue the pumps according to stop first or open first PID Display Setting according the site.
to ensure each pump can run and avoid the pump rusted because of long time N use. P12 ★
Range

6. Soft-start pump control mode (3) Constant pressure water supply special parameters
Set the soft start pump by E12 and through the input terminals o36 ~ o46,
Parameter Keyboard Setting Meanings
respectively controlled soft-start pump start and stop.
153 154
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction
Display
Starting pressure
E01 10% Starting pressure deviation is 10% select
deviation
Starting time Output signal
E02 2.0 Starting delay time is second. o21~o24 26 Low pressure arrival
delay select
E03 Stop frequency 15.00 stop at frequency 15HZ. Input terminal
o36~o46 51 Pump 1 soft start
E04 stop time delay 2.0 Stop time is 2 second. function select
feedback pressure reach and exceed the value of this Input terminal
High pressure o36~o46 52 Pump 1 stop
E05 80% parameter, the I / O output terminal select 25, then it
arrival value function select
will output arrival signal.
when feedback pressure less than the low pressure Input terminal
Low pressure o36~o46 53 Pump 2 soft starter
E06 60% reached value of this parameter, the I / O output function select
arrival
terminal select 26, then it will output arrival signal. Input terminal
o36~o46 54 Pump 2 stop
Timing to water function select
E07 0000 Timing to water supply function invalid
supply Input terminal
o36~o46 55 Pump 3 soft starter
function select
(4) Multi-function constant pressure water supply pump specific parameters Input terminal
Keyboard o36~o46 56 Pump 3 stop
Parameter Setting Meaning function select
Display
Input terminal
Timing shift According to first start first stop principles to control o36~o46 57 Pump 4 soft state
E08 0.25 function select
alternation time pump rotation, rotation time of 0.25 hours
Input terminal
o36~o46 58 Pump 4 stop
function select
electromagn When set up a station pump (drive motor) to switch Input terminal Manual shift command
o36~o46 59
etic switching from variable frequency industry frequency ,or from function select
E09 0.500
action delay industry frequency to variable frequency, and set its Input terminal
o36~o46 60 Timing of water supply time-zero
electromagnetic switching action delay time is 0.5 function select
seconds.
To set the determine time 100 seconds from inverter 8. Application Guide
output frequency reaches the upper limit
3 Pumps constant pressure water supply + sewage pump
Pumps shift frequencies until increase pump (drive motor); or
E10 100 1) pump configurations: variable frequency pump 3 units, 15kW, 1 unit sewage pump,
judging time from inverter output frequency reaches the lower
limit frequencies until decrease pump (drive 15kW.
motor). 2) The set pressure 0.8Mpa
Constant Decelerating stop: When the inverter failure, the 3) pressure gauge options: pressure transmitter, DC 4 ~ 20mA output, 1.6Mpa
Pressure Water 4) Inverter choice: PI8000 015F3 and WSC_RS485 water supply board
rotation switching way is from variable frequency
E11 Supply 0000
Configuration pump to industry frequency and the pump maintain the 5) Hardware Connection
status.
Multi-pump
E12 configuration 1111 N. 1 ~ 4 pumps are frequency controlled pump

Multi-pumps
Multi-pump control mode, displays the status of each
E13 status ★
pump
Soft-start Pump Multi-pump control mode, set the control mode of
E14 0000
Control each pump, currently set to Full Stop

(5) constant pressure water supply IO parameter:

Keyboard
Parameter Setting Meanings
Display
o21~o24 Output signal 25 High pressure arrival

155 156
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction

Display
Multi-pump constant pressure water supply, need
constant pressure water supply interface board, while
E00 Loading type 9
realize 4 pump constant pressure water supply pump
function.

② PID adjust in constant pressure water supply

Keyboard
Parameter Setting Meanings
Display
Keyboard set
F01 0 Keyboard set the frequency 0hz
frequency
F02
Frequency main
0 Keyboard set frequency or RS485 set frequency.
set mode
Frequency
F03 secondary set 7 PID adjusting mode
mode
elationship
F04 between main
and auxiliary 2 main+ auxiliary set mode
frequencies
given
Running control
F05 3 Terminal control
mode
single-way, the negative regulator, failure is not
P00 PID configure 0000
action
Feedback signal
P02 3 External analog feedback signal given by the AI3
select
Give signal
P03 2 External analog given by AI2
select
PID integration
P05 0.250 Setting according the site.
time
PID differential
P06 0 Setting according the site.
time
PID proportional
P07 100.0 Setting according the site.
gain
P09 Deviation Limit 5.0 Setting according the site.
PID Display adjust according actual requirement, display the
P12 1.6
Range actual pressure value is160.0 , it means1.6Mpa.

③ Constant pressure water supply specific parameters

1) Parameter settings Keyboard

Parameter Setting Meanings
Display
Starting pressure
① loading types with a constant pressure water supply function: E01 10% Starting pressure deviation is 10%
deviation
Starting time
Paramete Value Read Setting E02 2.0 Starting delay time is second.
Meanings delay
r On Keyboard Value
157 158
 Appendix V Converter Water Supply Controller Instruction Appendix V Converter Water Supply Controller Instruction
shutdown
E03 15.00 shutdown at frequency 15HZ.
frequency
select 1
Shutdown time
E04 2.0 shutdown time is 2 second. O2 input signal
delay o22 26 Low pressure arrival
hen feedback pressure reach and exceed the high select 2
High pressure pressure reached value of this parameter, the I / O O3 input signal
E05 80% o23 1 Fault input alarm
arrival output terminal select 25, then it will output arrival select 3
signal.
(DI1) input
when feedback pressure less than the low pressure
Low pressure o36 terminal function 1 FWD
E06 60% reached value of this parameter, the I / O output
arrival selection
terminal select 26, then it will output arrival signal.
Regular time (DI2)input
E07 0000 Regular time water supply function invaid
water supply o37 terminal function 39 Free parking
selection
④ Multi-function constant pressure water supply pump specific parameters (DI3 input
o38 terminal function 59 Manual rotation command
selection
Keyboard (DI4) input
Parameter Setting Meaning o39 terminal function 60 Timing of water supply time-zero
Display
E08 regular According first start first stop principles to control selection
E08 0.25
rotation interval pump rotation, rotation time of 0.25 hours (DI5) input
o40 terminal function 55 Pump 3 soft starting
selection
Electromagnetic When set up a station pump (drive motor) to switch
(DI6) input
switching action from variable frequency industry frequency ,or from
E09 0.500 o41 terminal function 56 Pump 3 stopping
delay industry frequency to variable frequency, and set its selection
electromagnetic switching action delay time is 0.5
seconds.
To set the determine time 100 seconds from inverter
output frequency reaches the upper limit frequencies
Pump switch to
E10 100 until increase pump (drive motor); or from inverter
judge the time
output frequency reaches the lower limit frequencies
until decrease pump (drive motor).
Constant Shutdown: When the inverter failure, the rotation
Pressure Water
switching way is from variable frequency pump to
E11 Supply 0
Configuration industry frequency and the pump maintain the
status.
Multi-pump
N. 1 ~ 3 pumps are frequency controlled pump,
E12 configuration 0000
pump 4 is soft-starter controlled pump.
Multi-pump
Multi-pump control mode, displays the status of
E13 status 1112
each pump
Soft-start Pump Multi-pump control mode, set the control mode of
E14 ★
Control each pump, i currently set to Full Stop

⑤ constant pressure water supply IO parameters:

Value read On
Setting
Parameter Keyboard Meanings
Value
Display
o21 O1 input signal 25 High pressure arrival
159 160