Scribd Logo
Upload

Welcome to Scribd!

  • 254 views

    D 600 MM or R 300 MM N 200 R.P.M. 0.25 270 Degrees 4.173 Rad Power 35 KW

    Uploaded by

    Jhun Briones
    A band brake is used to stop a 600mm diameter drum rotating at 200 rpm. The brake has a 270 degree contact angle and is attached to a fixed pin and a brake arm 120mm away. The minimum pull needed at the end of the 790mm brake arm to absorb 34kW of power and stop the drum is 292N.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    D 600 MM or R 300 MM N 200 R.P.M. 0.25 270 Degrees 4.173 Rad Power 35 KW

    Uploaded by

    Jhun Briones
    254 views2 pages
    A band brake is used to stop a 600mm diameter drum rotating at 200 rpm. The brake has a 270 degree contact angle and is attached to a fixed pin and a brake arm 120mm away. The minimum pull needed at the end of the 790mm brake arm to absorb 34kW of power and stop the drum is 292N.

    Original Title

    Brakes-1

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    A band brake is used to stop a 600mm diameter drum rotating at 200 rpm. The brake has a 270 degree contact angle and is attached to a fixed pin and a brake arm 120mm away. The minimum pull needed at the end of the 790mm brake arm to absorb 34kW of power and stop the drum is 292N.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    254 views2 pages

    D 600 MM or R 300 MM N 200 R.P.M. 0.25 270 Degrees 4.173 Rad Power 35 KW

    Uploaded by

    Jhun Briones
    A band brake is used to stop a 600mm diameter drum rotating at 200 rpm. The brake has a 270 degree contact angle and is attached to a fixed pin and a brake arm 120mm away. The minimum pull needed at the end of the 790mm brake arm to absorb 34kW of power and stop the drum is 292N.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    1.

    A band brake is used to operate on a 600 mm diameter drum that is rotating at


    200 rpm. The coefficient of friction is 0.25. The band brake has an angle of
    contact of 270 and one end is fastened to a fixed pin while the other end is
    fastened on the brake arm 120 mm from the fixed pin. The straight brake arm is
    placed 790 mm long and perpendicular to the diameter bisecting the angle of
    contact. Determine the minimum pull necessary at the end of the brake arm to
    stop the drum if 34 kW is absorbed.
    Given:
    d = 600 mm or r = 300 mm
    N = 200 r.p.m.
    µ = 0.25
    θ = 270 degrees = 4.173 rad
    Power = 35 kW

    Solving for the ratio of the tensions:

    T1
    2.3 log ( )=µθ
    T2
    T 1 0.25 x 4.173
    log ( )=
    T2 2.3
    T1
    ( )=3.25
    T2

    Solving for the braking torque of the drum:


    P
    T B=
    w
    3
    35 x 10
    T B=
    2 π x 200
    60
    T B=1672 N−m
    Solving for T 1:
    T B=r (T 1−T 2 )
    3
    1672 x 10 =300 (T 1−T 2 )

    ( T 1−T 2 )=5573 N
    T1
    Since ( )=3.25:
    T2
    T 1=3.25 T 2

    T 2=2477 N

    T 1=8050 N

    Taking moments about O:


    ∑M=0
    (Px750) – (T 2 x OD ¿=0
    OE
    OD=
    cos 45
    OD=88.4 mm
    T2xO D
    P=
    750
    2477 x 88.4
    P=
    750
    P=292 N

    You might also like