300+ TOP PIPING Engineering Interview Questions and Answers PDF

12/8/21, 7:10 AM 300+ TOP PIPING Engineering Interview Questions and Answers pdf
HOME Interview Questions MCQs *LAB VIVA CLASS NOTES SEMINAR TOPICS
ONLINE TEST GATE CAT Internship ABOUT US Privacy Policy
Any Skill Sea
Home » PIPING Engineering Interview Questions » 300+ TOP

PIPING Engineering Interview Questions and Answers
pdf
300+ TOP PIPING Engineering

Interview Questions and Answers
pdf
Ads by
Send feedback Why this ad?
PIPING Engineering Interview Questions :-
https://engineeringinterviewquestions.com/piping-engineering-interview-questions-answers-pdf/ 1/22
1 . What is preferred location for drain?
Must be located at the bottom section of drum.
2 . What are the steps in selection of valve?
What to handle, liquid, gas or powder, fluid nature, function,

construction material, disc type, stem type, how to operate, bonnet
type, body ends, delivery time, cost, warranty.
3. What are functions of valves?
Isolation, regulation, non-return and special purposes.
Ads by
4. What are isolating valves?
Gate, ball, plug, piston, diaphragm, butterfly, pinch.
5. What are regulation valves?
Globe, needle, butterfly, diaphragm, piston, pinch.
6. What are non-return valves?
check valve,
7. What are special valves?
multi-port, flush bottom, float, foot, pressure relief, breather.
8. What materials are used for construction of valves?
Cast iron, bronze, gun metal, carbon steel, stainless steel, alloy
carbon steel, polypropylene and other plastics, special alloys.
9. What is trim?
Trim is composed of stem, seat surfaces, back seat bushing and

other small internal parts that normally contact the surface fluid.
Ads by
10. Which standard specifies trim numbers for valve?
API 600.
11. What are wetted parts of valve?
All parts that come in contact with surface fluid are called wetted
parts.
12. What is wire drawing?
This term is used to indicate the premature erosion of the valve seat
caused by excessive velocity between seat and seat disc, when valve
is not closed tightly.
13. What is straight through valve?
Valve in which the closing operation of valve is achieved by 90

degrees turn of the closing element.
14. What pressure tests are carried out on valves?
Shell-hydrostatic, seat-hydrostatic, seat-pneumatic
15. What are available valve operators?
Hand-lever, hand-wheel, chain operator, gear operator etc.
16. What is the full form of ASME?
American Society for Mechanical Engineers.
17. Which Piping code is used for Power piping and which

code is used for Process Piping design?
ANS:
Power Piping: ASME B 31.1

Process Piping: ASME B 31.3
18. What are the main differences between ASME B 31.1

and ASME B 31.3?
The main differences are listed below:
Material allowable stresses are different in both codes.

Stress increases due to occasional loads are different in each
code.
B 31.3 neglects torsion while calculating sustained stresses,
but B 31.1 includes it.
Sustained stress calculation is specific in B 31.1 but undefined
for B 31.3.
B 31.1 intensifies torsion but B31.3 does not intensify it.
19. How to calculate the basic allowable stress for a

material?
The basic allowable stress is defined in respective code. For example

as per B 31.3 the basic allowable stress for a material is the
minimum of the following:
1/3rd of tensile strength at design temperature.
2/3rd of yield strength at design temperature.
100% of average stress for a creep rate of 0.01% per 1000 hours.
67% of average stress for rupture at the end of 100000 hours.
80% of minimum stress for ruptures at the end of 100000 hours.
For austenitic stainless steel or nickel alloys the lower of yield

strength and 90% of yield strength at temperature.
For structural grade materials 0.92 times of the lowest value of

point (a) to (f)
20. What is the main difference between Constant and

Variable Spring Hanger? When to use these hangers?
ANS:
In Constant Spring hanger the load remains constant

throughout its travel range. But In variable spring hanger the
load varies with displacement.
Spring hangers are used when thermal displacements are
upwards and piping system is lifted off from the support
position. Variable spring hanger is preferable as this is less
costly.
Constant springs are used:
When thermal displacement exceeds 50 mm
When variability exceeds 25%
Sometimes when piping is connected to strain sensitive
equipment like steam turbines, centrifugal compressors etc
and it becomes very difficult to qualify nozzle loads by
variable spring hangers, constant spring hangers can be used.
21. What do you mean by variability? What is the industry

approved limit for variability?
Variability= (Hot Load-Cold load)/Hot load = (Spring Constant ×
displacement)/Hot load.
Limit for variability for variable spring hangers is 25%.
22. What are the major parameters you must address

while making a Spring Data-sheet?
Major parameters are: Spring TAG, Cold load/Installed load,

Vertical and horizontal movement, Piping design temperature,
Piping Material, Insulation thickness, Hydro-test load, Line number
etc.
23. How to calculate the height of a Variable Spring

hanger?
Select the height from vendor catalog based on spring size and
stiffness class.
For base mounted variable spring hanger the height is mentioned

directly. It is the spring height.
For top mounted variable spring hanger’s ass spring height with
turnbuckle length, clamp/lug length and rod length.
24. Can you select a proper spring hanger if you do not

make it program defined in your software?
What is the procedure?
In your system first decide the location where you want to install
the spring. Then remove all nearby supports which are not taking
load in thermal operating case. Now run the program and the
sustained load on that support node is your hot load. The thermal
movement in that location is your thermal movement for your
spring. Now assume variability for your spring. So calculate
Spring constant = (Hot load × variability)/displacement. Now with

spring constant and hot load enter any vendor catalog to select
spring inside the travel range.
25. What is the software available for performing piping

stress analysis?
Caesar II, AutoPipe etc.
26. What are the types of compressors?
Positive Displacement, Centrifugal and Axial, rotary screw, rotary

vane, rotary lobe, dynamic, liquid ring compressors.
27. What are types of compressor drives?
Electric motor, gas turbine, steam turbine and gas engine.
28. How Centrifugal compressors work?
High-speed impellers increase the kinetic energy of the gas,

converting this energy into higher pressures in a divergent outlet
passage called a diffuser. Large volume of gas at moderate pressure.
29. What are types of steam turbine and why are they
popular?
Condensing and non-condensing, Popular because can convert

large amounts of heat energy into mechanical work very efficiently.
30. Where gas turbine drive is used?
Desserts and offshore platforms where gas is available, for gas

transmission, gas lift, liquid pumping, gas re-injection and process
compressors.
31. What are the auxiliary equipments of compressor?
Lube oil consoles, Seal oil consoles, Surface condensers, Condensate

pump, Air blowers, Inlet air filters, waste heat system, compressor
suction drum, knock out pot, Pulsation dampner, volume bottles,
Inter and after coolers.
VG ACADEMY
Vg Academy
best online Civil Engineering coaching
Directions
32. What are the types of seal oil system?
Gravity and pressurized.
33. What factors to be considered while designing

compressor housing?
Operation, Maintenance, Climate conditions, Safety, Economics.
34. What are the compressor housing design points?
Floor elevation, building width, building elevation, hook centerline

elevation.
35. What are the types of compressor cases?
Horizontal split case, Vertical split case.
36. How to located temperature and pressure

instruments?
Temperature in liquid space, at down-comer side and pressure in

vapour space, in area except down-comer sector.
37. What are necessary parts of inlet line of compressor?
Block Valve, Strainer, Break out flanges in both inlet and outlet to
remove casing covers, Straightening vane in inlet line if not enough
straight piece in inlet line available, PSV in interstage line and in
discharge line before block valve.
38. What points to be considered for reciprocating

compressor piping layout?
High pulsation, simple line as low to grade as possible for

supporting, analog study, all branches close to line support and on
top, Isolate line support from adjacent compressor or building
foundations
39. What are the types of compressor shelters?
On ground with no shelter, Open sided structure with a roof,
Curtain wall structure (Temperate climates), Open elevated

installation, Elevated multi-compressor structure.
40. What are drum internals?
Demister pads, Baffles, Vortex breakers, Distribution piping.
41. What are drum elevation requirements?
NPSH, minimum clearance, common platforming, maintenance,

operator access.
42. What are drum supports?
Skirt for large drums, legs, lugs, saddles for horizontal drums.
Ads by
High Volume Rubber Moulding
Our Production Floor Operates Off a Fully Integr

System
Van Ryn Rubber Holdings
43. What are necessary nozzles for non-pressure vessel?
Inlet, outlet, vent, manhole, drain, overflow, agitator, temperature

element, level instrument, and steam-out connection.
44. What are necessary nozzles for pressure vessel?
Inlet, outlet, manhole, drain, pressure relief, agitator, level gauge,

pressure gauge, temperature element, vent and for steam-out.
45. What is preferred location for level instrument

nozzles?
Away from the turbulence at the liquid outlet nozzle, although the
vessel is provided with a vortex breaker, instrument should be set in
the quiet zone of the vessel for example on the opposite side of the
weir or baffle or near the vapor outlet end.
46. What is preferred location for process nozzles on

drum?
Minimum from the tangent line.
47. What is preferred location for steam out nozzle on

drum?
At the end opposite to the maintenance access.
48. What is preferred location for vent?
AT the top section of drum at the end opposite the steam out
connection.
49. What is preferred location for pressure instrument

nozzle on drum?
Must be anywhere in the vapor space, preferable at the top section

of drum
50. What is preferred location for temperature

instrument?
Must be in liquid space, preferably on the bottom section of drum.
51. What are various temporary closures for lines?
Line blind valve, line blind, spectacle plate, double block and bleed,
blind flanges replacing a removable spool.
52. Why horizontal displacement is specified in data-

sheet? What will you do if the angle due to displacement
is more than 4 degree?
For bottom mounted springs it is mentioned to avoid large spring

bending by frictional force and displacement. So that additional
measures can be taken to lower frictional force by providing
PTFE/graphite slide plate.
For top mounted spring hangers horizontal displacement is

mentioned to check angularity of 4 degree to reduce transmission of
horizontal force to piping systems as spring hangers are designed to
take the vertical load only.
If angle becomes more than 4 degree due to large horizontal

movement then install the spring hanger in a offset position so that
after movement the angle becomes less than 4 degree.
53. Which spring will you select for your system: Spring
with low stiffness or higher stiffness and why?
Springs with lower stiffness provides less load variation for same
travel. So this spring is a better choice than a spring hanger with
higher stiffness.
54. What do you mean by Stress? What are the types of

Stresses that are generated in a Piping?
Whenever a force is applied to any object it applies a reaction force

against the deformation by that force. That reaction force per unit
area is the measure for the generated stress.
There has to be an external force to create stress. In a piping system

there are various reasons for the generation of stress like Piping
Weight, Internal and External pressure, Change in temperature,
Seismic and Wind forces, PSV reaction force etc.
The stresses generated in a piping system are as follows:
Axial Stresses
Tangential or Hoop stress
Longitudinal Stress
Radial Stress
Expansion Stress
Stress due to occasional events like Seismic and Wind effects.
55. What factors to consider for site selection?
District classification, Transportation facilities, Manpower

availability, industrial infrastructure, community infrastructure,
availability of raw water, effluent disposal, availability of power,
availability of industrial gas, site size and nature, ecology and

pollution.
56. Why Stress Analysis is required?
Ensure reliability and safety of working by
Limiting Stresses (sustained, expansion, hydro-test,

occasional) within code allowable.
Limiting nozzle load and moments connected to equipment
(Pump/Vessel/Heat Exchanger etc) within allowable values.
Reducing damaging effects of dynamic loads.
Avoiding leakage at joints.
Limiting sagging and displacements within allowable limits.
Avoiding high loads on supporting structures.
57. What is the difference between Stress and Pressure?
Stress is generated because of internal resistance force. Pressure is

generated because of external force.
Pressure can be a cause to generate stress.
58. Where jacked screwed flange is used?
For spectacle discs, one flange is jacked screw flange. This flange
has two jacked screws 180 degree apart which are used to create
sufficient space between flange for easy removal and placement of
line blind or spectacle blind.
59. What is double block and bleed?
Two valves with bleed ring in between with a bleed valve connected
to the hole of bleed ring.
60. Where blind flange is used?
It is used with view to future expansion of the piping system, or for

cleaning, inspection etc.
61. What are crude oil ranges?
Crude oil BP Range: 100F-1400F, lightest material: below 100F,

Heavier materials- upto 800F, Residue above 800F.
62. What is batch shell process?
feed, heat, condense, heat more, condense, low quality.
63. What are types of towers?
Stripper, Vacuum tower, trayed, packed towers.
64. What is chimney tray?
It’s a solid plate with central chimney section, used at draw-off

sections of the tower.
65. What factors to consider while setting tower

elevation?
NPSH, Operator access, Maintenance access, Minimum clearance,

re-boiler type , common area, type of support, Tower dimensions,
type of head, bottom outlet size, foundation details, minimum
clearances.
66. How to located tower maintenance access nozzles?
At bottom, top and intermediate sections of tower, must not be at

the down-comer section of tower and in front of internal piping.
67. How to located feed nozzle?
Must be oriented in specific area of tray by means of internal

piping.
68. What are the steps in selection of valve?
What to handle, liquid, gas or powder, fluid nature, function,

construction material, disc type, stem type, how to operate, bonnet
type, body ends, delivery time, cost, warranty.
69. What are functions of valves?
Isolation, regulation, non-return and special purposes.
70. What are isolating valves?
Gate, ball, plug, piston, diaphragm, butterfly, pinch.
71. What are regulation valves?
Globe, needle, butterfly, diaphragm, piston, pinch.
72. What are non-return valves?
check valve.
73. What are special valves?
multi-port, flush bottom, float, foot, pressure relief, breather.

74. What materials are used for construction of valves?
Cast iron, bronze, gun metal, carbon steel, stainless steel, alloy
carbon steel, polypropylene and other plastics, special alloys.
75. What is trim?
Trim is composed of stem, seat surfaces, back seat bushing and

other small internal parts that normally contact the surface fluid.
76. Which standard specifies trim numbers for valve?

API 600.
77. What are wetted parts of valve?
All parts that come in contact with surface fluid are called wetted
parts.
78. What is wire drawing?
This term is used to indicate the premature erosion of the valve seat
caused by excessive velocity between seat and seat disc, when valve
is not closed tightly.
79. What is straight through valve?
Valve in which the closing operation of valve is achieved by 90

degrees turn of the closing element.
80. What pressure tests are carried out on valves?
Shell-hydrostatic, seat-hydrostatic, seat-pneumatic
81. What are available valve operators?
Handlever, handwheel, chain operator, gear operator, powered

operator likes electric motor, solenoid, pneumatic and hydraulic
operators, Quick acting operators for non-rotary valves (handle lift).
82. What are ball valve body types?
Single piece, double piece, three piece, the short pattern, long
pattern, sandwich and flush bottom design.
83. What are two types of ball valve?
Full port design and regular port design, according to type of seat,
soft seat and metal seat.
84. Why ball valves are normally flanged?
Because of soft seat PTFE which can damage during welding.
85. What are butterfly valve types?
Double flange type, wafer lug type and wafer type.
86. What are types of check valve?
Lift check valves and swing check valves.
87. What are non-slam check valves?
Swing check valve, conventional check valve, wafer check valve,

tilting disc check valve, piston check valve, stop check valve, ball
check valve.
88. Where stop check valve is used?
In stem generation by multiple boilers, where a valve is inserted

between each boiler and the main steam header. It can be optionally
closed automatically or normally.
89. Where diaphragm valves are used?
Used for low pressure corrosive services as shut off valves.
90. What is Barstock Valve?
Any valve having a body machined from solid metal (barstock).
Usually needle or globe type.
91. What is BIBB Valve?
A small valve with turned down end, like a faucet.
92. What is Bleed Valve?
Small valve provided for drawing off liquid.
93. What is BlowDown Valve?
Refers to a plug type disc globe valve used for removing sludge and
sedimentary matter from the bottom of boiler drums, vessels,
driplegs etc.
94. What is Breather Valve?
A special self acting valve installed on storage tanks etc. to release

vapour or gas on slight increase of internal pressure (in the region
of ½ to 3 ounces per square inch).
95. What is Drip Valve?
A drain valve fitted to the bottom of a droplet to permit blowdown.
96. What is Flap Valve?
A non return valve having a hinged disc or rubber or leather flap

used for low pressure lines.
97. What is Hose Valve?
A gate or globe valve having one of its ends externally threaded to

one of the hose thread standards in use in the USA. These valves are
used for vehicular and firewater connections.
98. What is Paper-Stock Valve?
A single disc single seat gate valve (Slide gate) with knife edged or
notched disc used to regulate flow of paper slurry or other fibrous
slurry.
99. What is Root Valve?
A valve used to isolate a pressure element or instrument from a line

or vessel, or a valve placed at the beginning of a branch form the
header.
100. What is Slurry valve?
A knife edge valve used to control flow of non-abrasive slurries.
101. What is Spiral sock valve?
A valve used to control flow of powders by means of a twistable

fabric tube or sock.
102. What is Throttling valve?
Any valve used to closely regulate flow in the just-open position.
103. What is Vacuum breaker?
A special self-acting valve or any valve suitable for vacuum service,

operated manually or automatically, installed to admit gas (usually
atmospheric air) into a vacuum or low-pressure space. Such valves
are installed on high points of piping or vessels to permit draining
and sometimes to prevent siphoning.
104. What is Quick acting valve?
Any on/off valve rapidly operable, either by manual lever, spring or

by piston, solenoid or lever with heat-fusible link releasing a weight

which in falling operates the valve. Quick acting valves are desirable
in lines conveying flammable liquids. Unsuitable for water or for
liquid service in general without a cushioning device to protect
piping from shock.
105. What is diverting valve?
This valve switch flow from one main line to two different outlets.
WYE type and pneumatic control type with no moving part.
106. What is sampling valve?
Usually of needle or globe pattern, placed in branch line for the

purpose of drawing all samples of process material through the
branch.
107. What are blow off valve?
It is a variety of globe valve confirming with boiler code

requirements and specially designed for boiler blow-off service.
WYE pattern and angle type, used to remove air and other gases
from boilers etc.
108. What is relief valve?
Valve to relieve excess pressure in liquids in situations where full

flow discharge is not required, when release of small volume of
liquid would rapidly lower pressure.
109. What is safety valve?
Rapid opening (popping action) full flow valve for air and other
gases.
110. What is foot valve?
Valve used to maintain a head of water on the suction side of sump

pump, basically a lift check valve with integrated strainer.
111. What is float valve?
Used to control liquid level in tanks, operated by float, which rises

with liquid level and opens the valve to control water level. It can
also remove air from system, in which case, air flows out of system
in valve open condition, but when water reaches valve, float inside
valve raises to close the valve and stop flow of water. Used in drip
legs.
112. What are flush bottom valves?
Special type of valves used to drain out the piping, reactors and
vessels, attached on pad type nozzles.
113. What are types of flush bottom valves?
Valves with discs opening into the tank and valves with disks into
the valve.
114. What are the uses of three-way valve?
Alternate connection of the two supply lines to a common delivery

vise versa, isolating one safety valve, division of flow with isolation
facility.
115. What are uses of four way valve?
Reversal of pump suction and delivery, By pass of strainer or meter,

reversal of flow through filter, heat exchanger or dryer.
116. What is metal seated lubricated plug valve?
A plug valve with no plastic material, where grease is applied to

contacting surfaces for easy operation.
117. What are three patterns of plug valve design?
Regular pattern, short pattern and ventury pattern.
118. What is regular pattern plug valve?
Rectangular port, area almost equal to pipe bore, smooth transition

from round body to rectangular port, for minimum pressure loss.
119. What are short pattern plug valve?
Valves with face to face dimension of gate valve, as a alternative to

gate valve.
120. What are ventury pattern plug valve?
Change of section through the body throat so graded to have

ventury effect, minimum pressure loss.
121. What are inverted plug design valve?
Plug valve with taper portion up of plug. For 8” and higher size.
122. What is pressure balanced plug valve?
With holes in port top and bottom connecting two chambers on top
and bottom of plug, to reduce turning effort.
123. What are Teflon sleeved plug valve?
PTFE sleeve between plug and body of valve, low turning effort,
minimum friction, temperature limitation, anti static design
possible.
124. What are permasil plug valve?
Plug valves with Teflon seat instead of sleeves, for on-off

applications, can handle clean viscous and corrosive liquids,
Graphite seat for high temperature applications. Drip tight shut off
not possible.
125. What are eccentric plug valve?
Off center plug, corrosive and abrasive service, on off action, moves
into and away from seat eliminating abrasive wear.
126. What is dimensional standard for plug valve?
API 599.
127. What is pinch valve?
Similar to diaphragm valve, with sleeves of rubber or PTFE, which

get squeezed to control or stop the flow, Cast iron body, for very low
service pressures like isolation of hose connections, manufacture
standard.
128. What is needle valve?
Full pyramid disc, same design as globe valve, smaller sizes, sw or

threaded, flow control, disc can be integral with stem, inside screw,
borged or barstock body and bonnet, manufacturers standard.
129. How to install a globe valve?
Globe valve should be installed such that the flow is from the
underside of the disk, Usually flow direction is marked on the globe
valve.
130. What are globe valve port types?
Full port: More than 85% of bore size, Reducer port: One size less
than the connected pipe.
131. What are globe valve disk types?
Flat faced type for positive shutoff, loose plug type for plug renewal
or needle type for finer control.
132. What are characteristics of globe valve stem?
Always rising design, with disk nut at the lower end and handwheel
at upper end.
133. What are types of globe valve?
Angle globe valve, plug type disc globe valve, WYE-body globe
valve, composite disc globe valve, double disc globe valve.
134. What is angle globe valve?
Ends at 90 degree to save elbow, higher pressure drop.
135. Where plug type disc globe valve is used?
For severe regulating service with gritty liquids such as boiler

feedwater and for blow off service.
136. Where WYE body globe valve is used?
In line ports with stem emerging at 45 degree, for erosive fluids due
to smoother flow pattern.
137. What is double disc globe valve?
Has two discs bearing on separate seats spaced apart, on a single

shaft, for low torque, used for control valves.
138. What are port types for gate valves?
Full port and reduced port. Default is reduced bore. Full port has to
be specified in bom.
139. How to close a gate valve?
Turn the hand-wheel in clockwise direction.
140. What is lantern ring?
It’s a collection point to drain off any hazardous seepage or as a

point where lubricant can be injected; it is in the middle of packing
rings.
141. What are types of gate valves?
Solid plane wedge, solid flexible wedge, split wedge, double disc
parallels seats, double disc wedge, single disc single seat gate or
slide, single disc parallel seats, plug gate valve.
142. What are the types of bonnets?
Bolted bonnet, bellow sealed bonnet, screwed on bonnet, union

bonnets, A U-bolt and clamp type bonnet, breech-lock bonnet,
pressure seal bonnet.
PIPING Engineering Questions and Answers pdf free download

::
---- >> Related Posts Of Above Questions :::
------>>[MOST IMPORTANT]<<------
1. 300+ TOP Piping Design Engineer Interview

Questions & Answers
2. 300+ TOP Piping Interview Questions & Answers
3. 300+ [UPDATED] Mechanical Fitter Interview
Questions and Answers
4. 250+ MCQs on Instrumentation and Control –
Agitation and Foam Sensing and Valves and
Answers
5. 250+ TOP MCQs on Different Types of Valves and
Answers
6. 250+ TOP MCQs on Pneumatic Actuating Systems –
Process Control Valves and Answers
7. 300+ TOP Valves Interview Questions – Answers
8. 250+ TOP MCQs on Pipes, Valves and Fittings and
Answers
9. 300+ TOP Safety Relief Valves Interview Questions
[UPDATED]
10. 250+ TOP MCQs on Engine Valves and their
Mechanisms and Answers
11. 300+ TOP MARINE Engineering Interview
12. 300+ [UPDATED] Control Valves Interview
Questions
13. 250+ TOP MCQs on Subsurface Control Equipment

and Answers
14. 250+ TOP MCQs on Types of Valves and Answers
15. 300+ TOP Instrumentation Engineering Interview
16. 250+ TOP MCQs on Boiler Mountings – 2 and
Answers
17. 250+ TOP MCQs on Poppet Valves and Answers
18. 250+ TOP MCQs on Boiler Mounting Accessories –
1 and Answers
19. 300+ TOP Industrial Instrumentation Interview
Questions [LATEST]
20. 250+ TOP MCQs on Pressure Regulators and
Answers
ONE THOUGHT ON “300+ TOP PIPING ENGINEERING

INTERVIEW QUESTIONS AND ANSWERS PDF”
marcos rosa
NOVEMBER 26, 2019 AT 10:58 PM
how can i do the download of this doc? where i

click?
REPLY
LEAVE A REPLY
Your email address will not be published. Required fields are marked *
Comment
Name *
Email *
Website
Post Comment
Engineering 2021 , Engineering Interview Questions.com , Theme by Engineering||

Privacy Policy||
Terms and Conditions||
ABOUT US||
Contact US||
Engineering interview questions,Mcqs,Objective Questions,Class Lecture Notes,Seminor topics,Lab
Viva Pdf PPT Doc Book free download. Most Asked Technical Basic CIVIL | Mechanical | CSE | EEE |
ECE | IT | Chemical | Medical MBBS Jobs Online Quiz Tests for Freshers Experienced .

300+ TOP PIPING Engineering Interview Questions and Answers PDF

Uploaded by

Copyright:

Available Formats

300+ TOP PIPING Engineering Interview Questions and Answers PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

300+ TOP PIPING Engineering Interview Questions and Answers PDF

Uploaded by

Copyright:

Available Formats

12/8/21, 7:10 AM 300+ TOP PIPING Engineering Interview Questions and Answers pdf

Any Skill Sea

Home » PIPING Engineering Interview Questions » 300+ TOP

300+ TOP PIPING Engineering

PIPING Engineering Interview Questions :-

1 . What is preferred location for drain?

Must be located at the bottom section of drum.

2 . What are the steps in selection of valve?

What to handle, liquid, gas or powder, fluid nature, function,

3. What are functions of valves?

Isolation, regulation, non-return and special purposes.

4. What are isolating valves?

Gate, ball, plug, piston, diaphragm, butterfly, pinch.

5. What are regulation valves?

Globe, needle, butterfly, diaphragm, piston, pinch.

6. What are non-return valves?

7. What are special valves?

multi-port, flush bottom, float, foot, pressure relief, breather.

8. What materials are used for construction of valves?

Trim is composed of stem, seat surfaces, back seat bushing and

10. Which standard specifies trim numbers for valve?

11. What are wetted parts of valve?

12. What is wire drawing?

13. What is straight through valve?

Valve in which the closing operation of valve is achieved by 90

14. What pressure tests are carried out on valves?

Shell-hydrostatic, seat-hydrostatic, seat-pneumatic

15. What are available valve operators?

Hand-lever, hand-wheel, chain operator, gear operator etc.

16. What is the full form of ASME?

American Society for Mechanical Engineers.

17. Which Piping code is used for Power piping and which

Power Piping: ASME B 31.1

18. What are the main differences between ASME B 31.1

The main differences are listed below:

Material allowable stresses are different in both codes.

19. How to calculate the basic allowable stress for a

The basic allowable stress is defined in respective code. For example

1/3rd of tensile strength at design temperature.

2/3rd of yield strength at design temperature.

67% of average stress for rupture at the end of 100000 hours.

80% of minimum stress for ruptures at the end of 100000 hours.

For austenitic stainless steel or nickel alloys the lower of yield

For structural grade materials 0.92 times of the lowest value of

20. What is the main difference between Constant and

In Constant Spring hanger the load remains constant

21. What do you mean by variability? What is the industry

Limit for variability for variable spring hangers is 25%.

22. What are the major parameters you must address

Major parameters are: Spring TAG, Cold load/Installed load,

23. How to calculate the height of a Variable Spring

For base mounted variable spring hanger the height is mentioned

24. Can you select a proper spring hanger if you do not

What is the procedure?

Spring constant = (Hot load × variability)/displacement. Now with

25. What is the software available for performing piping

Caesar II, AutoPipe etc.

26. What are the types of compressors?

Positive Displacement, Centrifugal and Axial, rotary screw, rotary