f[Title]

Topology

Addressing Table
Device Interface IP Address Subnet Mask Default Gateway

S1 VLAN 1 192.168.1.2 255.255.255.0 N/A

PC-A NIC 192.168.1.3 255.255.255.0 192.168.1.1

Objectives
Part 1: Configure Devices and Verify Connectivity
Part 2: Display, Describe, and Analyze Ethernet MAC Addresses

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 9 www.netacad.com
[Title]

Background / Scenario
Every device on an Ethernet LAN is identified by a Layer 2 MAC address. This address is assigned by the
manufacturer and stored in the firmware of the NIC. This lab will explore and analyze the components that
make up a MAC address, and how you can find this information on a switch and a PC.
You will cable the equipment as shown in the topology. You will configure the switch and PC to match the
addressing table. You will verify your configurations by testing for network connectivity.
After the devices have been configured and network connectivity has been verified, you will use various
commands to retrieve information from the devices to answer questions about your network equipment.
Note: The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2) (lanbasek9 image). Other
switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the
commands available and the output produced might vary from what is shown in the labs.
Note: Make sure that the switches have been erased and have no startup configurations. If you are unsure,
ask your instructor.

Required Resources
 1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
 1 PC (Windows with a terminal emulation program, such as Tera Term)
 Console cable to configure the Cisco switch via the console ports
 Ethernet cables as shown in the topology

Instructions
Part 1: Configure Devices and Verify Connectivity
In this part, you will set up the network topology and configure basic settings, such as the interface IP
addresses and device name. For device name and address information, refer to the Topology and Addressing
Table.

Step 1: Cable the network as shown in the topology.

a. Attach the devices shown in the topology and cable as necessary.
b. Power on all the devices in the topology.

Step 2: Configure the IPv4 address for the PC.

a. Configure the IPv4 address, subnet mask, and default gateway address for PC-A.
b. From the command prompt on PC-A, ping the switch address.
Open a Windows command prompt
Question:

Were the pings successful? Explain.

Type your answers here.
Close a Windows command prompt

Step 3: Configure basic settings for the switch.

In this step, you will configure the device name and the IP address, and disable DNS lookup on the switch.
a. Console into the switch and enter global configuration mode.
Open a configuration window.

Switch> enable
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 9 www.netacad.com
[Title]

Switch(config)#
b. Assign a hostname to the switch based on the Addressing Table.
Switch(config)# hostname S1
c. Disable DNS lookup.
S1(config)# no ip domain-lookup
d. Configure and enable the SVI interface for VLAN 1.
S1(config)# interface vlan 1
S1(config-if)# ip address 192.168.1.2 255.255.255.0
S1(config-if)# no shutdown
S1(config-if)# end
*Mar 1 00:07:59.048: %SYS-5-CONFIG_I: Configured from console by console
Close a configuration window

Step 4: Verify network connectivity.

Open a Windows command prompt.

Ping the switch from PC-A.

Question:

Were the pings successful?

Yes.

Type your answers here.

Close a Windows command prompt.Display, Describe, and Analyze Ethernet MAC Addresses

Every device on an Ethernet LAN has a MAC address that is assigned by the manufacturer and stored in the
firmware of the NIC. Ethernet MAC addresses are 48-bits long. They are displayed using six sets of
hexadecimal digits that are usually separated by dashes, colons, or periods. The following example shows the
same MAC address using the three different notation methods:
00-05-9A-3C-78-00 00:05:9A:3C:78:00 0005.9A3C.7800

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 9 www.netacad.com
[Title]

Note: MAC addresses are also called physical addresses, hardware addresses, or Ethernet hardware
addresses.
You will issue commands to display the MAC addresses on a PC and a switch, and analyze the properties of
each one.

Step 5: Analyze the MAC address for the PC-A NIC.

Before you analyze the MAC address on PC-A, look at an example from a different PC NIC. You can issue
the ipconfig /all command to view the MAC address of your NIC. An example screen output is shown below.
When using the ipconfig /all command, notice that MAC addresses are referred to as physical addresses.
Reading the MAC address from left to right, the first six hex digits refer to the vendor (manufacturer) of this
device. These first six hex digits (3 bytes) are also known as the organizationally unique identifier (OUI). This
3-byte code is assigned to the vendor by the IEEE organization.
To find the manufacturer, use the keywords IEEE OUI standards to find an OUI lookup tool on the internet or
navigate to http://standards-oui.ieee.org/oui.txt to find the registered OUI vendor codes. The last six digits are
the NIC serial number assigned by the manufacturer.
a. Using the output from the ipconfig /all command, answer the following questions.
C:\> ipconfig /all
<output omitted>
Ethernet adapter Ethernet:

Connection-specific DNS Suffix . :

Description . . . . . . . . . . . : Intel(R) 82577LM Gigabit Network Connection
Physical Address. . . . . . . . . : 5C-26-0A-24-2A-60
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::b875:731b:3c7b:c0b1%10(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.147(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Friday, September 6, 2019 11:08:36 AM
Lease Expires . . . . . . . . . . : Saturday, September 7, 2019 11:08:36 AM
Default Gateway . . . . . . . . . : 192.168.1.1
<output omitted>
Questions:

What is the OUI portion of the MAC address for this device?
5C-26-0A-

Type your answers here.

What is the serial number portion of the MAC address for this device?
24-2A-60
24
Using the example above, find the name of the vendor that manufactured this NIC.
Type your answers here.
b. From the command prompt on PC-A, issue the ipconfig /all command and identify the OUI portion of the
MAC address for the NIC of PC-A.
Type your answers here.
Identify the serial number portion of the MAC address for the NIC of PC-A.

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 9 www.netacad.com
[Title]

Type your answers here.

Identify the name of the vendor that manufactured the NIC of PC-A.
Type your answers here.

Step 6: Analyze the MAC address for the S1 F0/6 interface.

You can use a variety of commands to display MAC addresses on the switch.
a. Console into S1 and use the show interfaces vlan 1 command to find the MAC address information. A
sample is shown below. Use output generated by your switch to answer the questions.
Open a configuration window

S1# show interfaces vlan 1

Vlan1 is up, line protocol is up
Hardware is EtherSVI, address is 001b.0c6d.8f40 (bia 001b.0c6d.8f40)
Internet address is 192.168.1.2/24
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:14:51, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
34 packets output, 11119 bytes, 0 underruns
0 output errors, 2 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 9 www.netacad.com
[Title]

Question:

What is the MAC address for VLAN 1 on S1?

00e0.8faa.4d01

Type your answers here.

What is the MAC serial number for VLAN 1?
bia 00e0.8faa.4d01 / aa.4d01
Type your answers here.
Type your answers here.
What does bia stand for?

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 9 www.netacad.com
[Title]

Type your answers here.

Why does the output show the same MAC address twice?
bia 00e0.8faa.4d01

Type your answers here.

b. Another way to display the MAC address on the switch is to use the show arp command. Use the show
arp command to display MAC address information. This command maps the Layer 2 address to its
corresponding Layer 3 address. A sample is shown below. Use output generated by your switch to
answer the questions.
S1# show arp

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 9 www.netacad.com
[Title]

Protocol Address Age (min) Hardware Addr Type Interface

Internet 192.168.1.2 - 001b.0c6d.8f40 ARPA Vlan1
Internet 192.168.1.3 0 5c26.0a24.2a60 ARPA Vlan1

What Layer 2 addresses are displayed on S1?

2C-F0-5D-B2-D6-5E
Type your answers here.
What Layer 3 addresses are displayed on S1?
192.168.1.3
Type your answers here.

Step 7: View the MAC addresses on the switch.

Issue the show mac address-table command on S1. A sample is shown below. Use output generated by
your switch to answer the questions.
S1# show mac address-table
Mac Address Table
-------------------------------------------

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 8 of 9 www.netacad.com
[Title]

Vlan Mac Address Type Ports

---- ----------- -------- -----
All 0100.0ccc.cccc STATIC CPU
All 0100.0ccc.cccd STATIC CPU
All 0180.c200.0000 STATIC CPU
All 0180.c200.0001 STATIC CPU
All 0180.c200.0002 STATIC CPU
All 0180.c200.0003 STATIC CPU
All 0180.c200.0004 STATIC CPU
All 0180.c200.0005 STATIC CPU
All 0180.c200.0006 STATIC CPU
All 0180.c200.0007 STATIC CPU
All 0180.c200.0008 STATIC CPU
All 0180.c200.0009 STATIC CPU
All 0180.c200.000a STATIC CPU
All 0180.c200.000b STATIC CPU
All 0180.c200.000c STATIC CPU
All 0180.c200.000d STATIC CPU
All 0180.c200.000e STATIC CPU
All 0180.c200.000f STATIC CPU
All 0180.c200.0010 STATIC CPU
All ffff.ffff.ffff STATIC CPU
1 5c26.0a24.2a60 DYNAMIC Fa0/6
Total Mac Addresses for this criterion: 21
Question:

Did the switch display the MAC address of PC-A? If you answered yes, what port was it on?
Yes, PCA

Type your answers here.

Reflection QuestionsCan you have broadcasts at the Layer 2 level? If so, what
would the MAC address be?
FF-FF-FF-FF-FF-FF
Type your answers here.
1. Why would you need to know the MAC address of a device?
There could be a variety of reasons. In a large network, it may be easier to pinpoint location and identity of a
device by its MAC address instead of its IP address. The MAC OUI will list the manufacturer, which may help
narrow down the search. Security measures can be applied at Layer 2, so knowledge of allowable MAC
addresses is needed

Type your answers here.

End of Document

 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 9 of 9 www.netacad.com