REGULATORY INFORMATION SHEET (RIS)

Rynite® 935 BK505

THERMOPLASTIC POLYESTER RESIN

Regulatory Information Sheet

For

Rynite® 935 BK505

Material description :

thermoplastic polyester resin

ISO 1043 identification: PET-(MD+GF)35

ISO 11469 part marking code: >PET-(MD+GF)35<

Content Table:

Food Contact, Drinking Water Contact and Toys

Electrical and Electronic Industry
Automotive Industry
Other Industries
Waste, Recycling and Recovery
Chemical Constituents

This document provides a summary of available information. In certain cases it may not respond to all questions. The amount of information requested in a
number of inquiries suggests, that the intent is to establish a regulatory profile of a given material. If this is the case, not all of the required information may be
relevant for the currently intended material use. We will be glad to further investigate missing information but would like to ask you to reconfirm which of the
missing information is critical for your use.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 1 of 13

dupont.com

The information set forth herein is furnished free of charge, is based on technical data that DuPont believes to be reliable, and represents typical values that fall within the normal range of
properties. This information relates only to the specific material designated and may not be valid for such material used in combination with other materials or in other processes. It is
intended for use by persons having technical skill, at their own discretion and risk. This information should not be used to establish specification limits nor used alone as the basis of design.
Handling precaution information is given with the understanding that those using it will satisfy themselves that their particular conditions of use present no health or safety hazards and
comply with applicable law. Since conditions of product use and disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any
use of this information. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as a license to operate or a recommendation
to infringe on patents.
CAUTION: Do not use DuPont materials in medical applications involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided
from DuPont under a written contract or other acknowledgement that is consistent with the DuPont policy regarding medical applications and expressly acknowledges the contemplated use.
For further information, please contact your DuPont representative.
DuPont’s sole warranty is that our products will meet our standard sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to
refund of purchase price or replacement of any product shown to be other than as warranted. TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, DUPONT SPECIFICALLY DISCLAIMS
ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR NON-INFRINGEMENT. DUPONT DISCLAIMS LIABILITY FOR ANY SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

DuPont™, the DuPont Oval Logo, and all trademarks and service marks denoted with ™, SM or ® are owned by affiliates of DuPont de Nemours, Inc. unless otherwise noted.
© 2022 DuPont. All rights reserved.
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

Basis for Declaration

All declarations are made versus the regulatory limits. For any lower declaration limits, please contact your
DuPont representative.

The compositions of our products are considered as proprietary. In specific cases disclosure can be considered
provided appropriate agreements are put in place.

In general we do not routinely analyse our products for compliance with the regulations mentioned below, nor do
we require our raw material suppliers to do so.
Below information is based on review of current formulation, composition, manufacturing process and
information supplied by vendors.

Global Chemical Management Legislation

Chemical Inventory

All the constituents of the above product are listed for DuPont purposes, or exempted on the following Chemical
Inventories (please contact your DuPont representative for information on potential restrictions, limitations or if
you are directly importing the product yourself into a specific country) :

US Toxic Substances Control Act (TSCA, Active Inventory)

Australian Inventory of Chemical Substances (AICS)
Canadian Domestics Substances List (DSL)
Inventory of Existing Chemical Substances in China (IECSC)
Japanese Existing and New Chemical Substances (ENCS)
Japanese Industrial Safety and Health Law (ISHL) Inventory
Korean Existing Chemicals Inventory (KECI)
Philippine Inventory of Chemicals & Chemical Substances (PICCS)
Taiwan Chemical Substance Inventory (TCSI)

European Economic Area (EEA) - REACH Registration Status

REACH registration is the responsibility of the importer or manufacturer of the substance.

If you have purchased the above product from DuPont in the EEA, exported the product, and intend to re-import
the product, DuPont or its suppliers have completely all required registrations. No further registration obligation is
expected from the importer.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 2 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN
If you have purchased DuPont products outside the EEA and plan to import it into EEA, please contact your
DuPont representative.

REACH SVHC

The European Chemicals Agency (ECHA) added additional substances to the Candidate List of Substances of Very
High Concern (SVHC) on January 17th, 2022.
The full list can be found here: https://echa.europa.eu/candidate-list-table.

In response to your inquiry, we have reviewed our available information regarding the presence of those
substances in the products you purchase. Please find the relevant information in this letter.

Please assess any legal obligations you may have to communicate the presence of SVHC substances in your
products, depending on the type of product that you manufacture. You can read more on requirements for articles
on the ECHA website: https://echa.europa.eu/regulations/reach/candidate-list-substances-in-articles.

DuPont is in the process of updating its Safety Data Sheets (SDSs) for products which contain >=0.1% of SVHC and
will send them to customers as soon as they are available.

The above product does not contain any of the Substances of Very High Concern listed in the REACH ‘Candidate
List’ (published in accordance with Article 59(10) of the REACH Regulation) as amended as per revision date of the
letter.

The above product does not contain any of the substances subject to authorization as listed on the Annex XIV of
Regulation (EC) N° 1907/2006 as amended as per revision date of the letter.
If present in this product, further information related to substances on REACH Annex XVII list can be found on the
Safety Data Sheet (SDS), Article Information Sheet (AIS) or SVHC letter.

Export control

The above product is not subject to US export control. It has been assigned with an ECCN of EAR99 under the US
regulation.
No substance mentioned in the European Regulation (EC) N° 689/2008, Annex I, part 1 is added in excess of the
limits set.

Food Contact, Drinking Water Contact and Toys

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 3 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

Good Manufacturing Practice for food contact

The requirements of the European Regulation (EC) n° 2023/2006 on Good Manufacturing Practice (GMP) for
materials and articles intended to come into contact with food don't apply to the product above

Food Contact

The above product is not supported for food (FDA) applications in USA.
The above product is not supported for food contact applications in Europe.
The above product is not supported for food contact applications in China.
The above product is not registered by JHOSPA.

Drinking Water Contact

The above product is not listed to be in contact with drinking water

Electrical and Electronic Industry

Waste Electric and Electronic Equipment (WEEE)

The material complies with the requirements of the European Directive 2012/19/EC (WEEE) and the Chinese Waste
electrical and electronic equipment legislation as far as apply to substances.

Restriction of Hazardous Substances (RoHS) and other metals

Results of the various analytical testing, auditing and process analysis techniques or review of current chemical
composition demonstrate that this material complies with the requirements of the Directive (EU) 2015/863 (RoHS
3) amending Annex II to directive 2011/65/EU (RoHS 2), 2003/11/EC (pentabromodiphenyl ether,
octabromodiphenyl ether), the Chinese Standard GB/T 26572 – 2011 (Chinese RoHS 2, 2016) and the Act for
Resource Recycling of Electrical and Electronic Equipment and Vehicles (Korea RoHS).

No metals* and compounds thereof are added.

* Antimony (Sb), Arsenic (As), Barium (Ba), Cadmium (Cd), hexavalent Chromium (CrVI), Lead (Pb), Mercury (Hg),
Selenium (Se).

However traces of Barium compound may be present.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 4 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

If present at all, the levels of cadmium (Cd), hexavalent chromium (CrVI), lead (Pb) and mercury (Hg) are below the
1994 CONEG guide-lines of 100 ppm (total amount), the limits of the European Directive 94/62/EC, and the
European Directive 2004/12/EC, (Packaging Waste Directive) of 100 ppm (total amount), as well as the European
Directive 2000/53/EC (ELV) as amended with the limits of 0.1% of Cr VI, Pb, Hg in homogeneous material and
0.01% of Cd and the European Directives 2011/65/EU (RoHS 2) / 2002/96/EC (WEEE) and the Chinese Waste
Electrical and Electronic Equipment legislation and the Chinese Regulation SJ/T 11363-2006 (Chinese RoHS) of
1000 ppm per metal.

IEC 62474 - Material Declaration for Products of and for the Electrotechnical Industry

As reference for substance to be declared the IEC 62474 list is used.

This list is accessible under http://std.iec.ch/iec62474

No substances above the limits of declaration of the IEC 62474 list are added.

Flame Retardants

During the manufacture of above product, neither polychlorinated biphenyls (PCB), nor polychlorinated triphenyls
(PCT), nor polychlorinated dibenzodioxines (PCDD), nor polychlorinated dibenzofuranes (PCDF), nor
polychlorinated biphenyl oxides/ester (PCBO/PCBE), nor polychlorinated diphenyl oxides/ester/ether
(PCDO/PCDE), nor polybrominated biphenyls (PBB), nor polybrominated triphenyls (PBT), nor polybrominated
biphenyl oxides/ester (PBBO/PBBE), nor polybrominated diphenyl oxides/ester/ether (PBDO/PBDE which include
penta-, octa- and deca-BDE), nor polybrominated dibenzodioxines (PBDD), nor polybrominated dibenzofuranes
(PBDF), nor Tetrabromobisphenol-A (TBBPA) are intentionally added.

Neither monomethyl dibromo diphenylmethane (DBBT), nor monomethyl dichloro diphenylmethane, nor
monomethyl tetrachloro diphenylmethane, nor hexabromocyclododecane (HBCD or HBCDD), nor Tris (2,3 –
dibromopropyl) phosphate (TRIS) are intentionally added.
Neither thiram (TMTD), nor triethyl phosphate are intentionally added.

The flame retardant system in flame retardant grades can be identified by the ISO 1043 code as mentioned on the
front page of this document.

Halogens

No halogenated* compounds are added in excess of the limits set by applicable regulations**.

Trace levels of halogenated compounds may be present.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 5 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

* brominated (Br), chlorinated (Cl), fluorinated (F), iodated (I).

** IEC 61249-2-21.
flame retardant additives listed in the European Directive (EU) 2015/863 (RoHS 3) amending Annex II to
directive 2011/65/EU (RoHS 2).

Automotive Industry

End of Life Vehicle (ELV)

Based on test of representative samples of above or similar materials or compositional information it has been
demonstrated that the above product complies with the requirements on heavy metals of the European Directive
2000/53/EC (End-of Life Vehicle directive) as amended.

GADSL - Global Automotive Declarable Substances List

As reference for substance to be declared the "Global Automotive Declarable Substance List" (GADSL) is used.
This List is accessible under www.gadsl.org

No substances above the limits of declaration of the GADSL list are added.

IMDS - International Material Data System

It is the policy of DuPont Polymers, to supply information in letter form along with legal disclaimers. The
following information on our products is provided to you free of charge in order to allow your company to identify
the appropriate IMDS data set.

Company name: DuPont

Company ID: 15082
Type: Material (MDS)
IMDS ID: 15093503

Caution:

The polymer identification and part marking code refer to the material composition (IMDS composition) but also
to the material property profile (IMDS symbol field). Therefore, in some cases, differences can appear, e.g in case
of impact modification (impact modifier added into the composition, but not generating properties that justify a
coding of impact modified polymer).

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 6 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

General information for all plastics and elastomers:

During drying, purging and moulding, small amounts of hazardous gases and/or particulate matter may be
released. These may irritate eyes, nose and throat.
Conditions of ‘Good manufacturing Practice’, state-of-the-art, fully operational workplace equipment and
conditions and respect of the suppliers handling, processing and use prescriptions and precaution have to be
assured.
The respect of exposure limits as per applicable Safety data Sheet has to be assured by the material user.
Like most thermoplastic plastics and thermoset elastomers, the product can be recycled. Where possible recovery
and recycling is preferred to disposal or incineration. Can be landfilled or incinerated, when in compliance with
local regulations.

Specific Information:

For grades containing Polyacetal (POM) polymer, some formaldehyde can be created during processing.
For grades containing glass fibers, these DO NOT represent Whisker-fibers which comply with the description of
the WHO for hazardous fibers* . (* Fibers with l > 5 µm, d < 3 µm, l:d > 3:1)

Declaration of recycle content (as per IMDS definition):

Following is the DuPont position: As for metals, glass, textile and paper products, within the raw material
specification limits, the feedstock may vary based on technical reasons and availability. Polymer materials
therefore have to be considered as 100% new materials if not otherwise indicated.

Validity of DuPont Polymer entries into IMDS

DuPont Polymer entries have been validated against the following substance* list:

GADSL list 2021, revision 1.0, released February 2021, http://www.gadsl.org/

Validity of entries: Up to 1st July 2022.

-----------------------------------------------------

*Important notice:
Concerning the GADSL entry 55 ‘Formaldehyde’, Threshold

Any intentionally added content of formaldehyde must be reported. Formaldehyde in any material, which may be
emitted under reasonable and foreseeable conditions, must be qualitatively indicated. Impurities of formaldehyde
above 0.1% has to be declared.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 7 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

DuPont offers polymers, which are based on formaldehyde as monomer. Monomers are not considered as
reportable, since in the material, as assembled to the vehicles, the monomers have been transformed into a solid
polymer.
The requirement ‘Any material with the potential to emit formaldehyde must be indicated’ would require an
appropriate input field in IMDS, which, however, is not available. Therefore, this GADSL required information is
provides through the ‘IMDS Reference Letters’, outside the IMDS system.

CAMDS - China Automotive Material Data System

Information concerning materials entered into CAMDS is available on request. Please contact your DuPont
representative for further information.

Other Industries

Öko-Tex

Restricted substances as listed in the Öko-Tex standard 100 are added.

For further information, contact your DuPont representative.

ChemSHERPA

Information concerning material available from ChemSHERPA is available on request. Please contact your DuPont
representative for further information.

JGPSSI & MSDS plus

DuPont does no longer support JGPSSI and MSDS Plus. However all necessary data defined by these topics can be
made available through ChemSHERPA. Please contact your DuPont representative for further information.

Waste, Recycling and Recovery

Recycling: Content Declaration for food contact compliant grades

If not otherwise indicated, no recycled materials from external sources are used for grades compliant with
European food contact regulations.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 8 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

Recycling: Content Declaration for industrial grades (as per IMDS definition)

As for metals, glass, textile and paper products, within the raw material specification limits, the feedstock may
vary based on technical reasons and availability. Polymer materials therefore have to be considered as 100% new
materials if not otherwise indicated.

Recycling of Packaging Materials: Metals Content (also refered to as ´heavy metals´)

CEN Report prCR 13695-1

None of the four named heavy metals, - cadmium, lead, mercury and hexavalent chromium, - have been
intentionally added to this product or the constituents contained in the product.

Recycling: Hazardous Substances

No listed noxious and hazardous substances have been intentionally added to this product or any of the
constituents contained.

Recycling of Packaging Materials: Recovery

CEN Standard prEN 13430

This raw material is suitable for recycling subject to the normal conditions of repetitive processing. The ability to
recycle following its use will depend on the detailed nature, composition and construction of the former article,
the potential contained residues and contamination, and the systems available, for collection and any necessary
sorting.

Recycling: Energy Recovery

CEN Standard prEN 13431

The calorific gain from the polymer in an energy recovery process is approximately 12 MJ/kg The amount and
nature of inert fillers, which represents the amount and nature of residual ash, can be obtained from the related
product literature, this does not contribute to the energy that may be recovered.

(Ref: CEN Standard 13431, example list of net caloric gain values, polyolefins)

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 9 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

Chemical Constituents

Conflict Minerals

No substances reportable under the ‘Dodd-Frank Wall Street Reform and Consumer Protection Act (2010)’ -
Conflict Minerals* originating in the Democratic Republic of Congo (DRC) or an adjoining country** - are
intentionally added during manufacturing of this above product.

* columbite-tantalite (coltan, tantalum), cassiterite (tin), gold, wolframite (tungsten), or derivatives.

**adjoining countries are Angola, Zambia, Tanzania, Uganda, Sudan, Rwanda, Burundi and the Central African
Republic.

The Conflict Minerals Reporting Template (CMRT) form has been completed for the above product and is
available on request.

Nanoparticles content

No material of nanoscale size (see below for definition) is added for its specific nanoscale properties during
manufacturing of above product.

The European Commission has defined nanomaterials under Recommendation 2011/696/EU.

These particles may be inextricably bound into a polymer matrix and thus may not require declaration under
certain country reporting requirements. Please contact your DuPont representative for more information.

Volatile Organic Compounds (VOC)

No Volatile Organic Compounds as defined in the European Directive 2010/75/EC.

The product contains less than 3% of components considered VOC according to the Swiss VOC Regulation, SR
814.018 (Annex I) or contains products manufactured in Switzerland, which are not on the positive list of products
(Annex II).

Ozone Depleting Substances (ODS)

No suspected Ozone Depleting Substances (ODS) of class I or II according to the US Clean Air Act, 1993
amendments, are used.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 10 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN
No suspected Ozone Depleting Substances (ODS) as mentioned in the Montreal Protocol of 1987, amended by the
London Convention in 1990, the Copenhagen Convention in 1992, the Vienna Convention in 1995, the Montreal
Convention in 1997 and the Beijing Convention in 1999, are used.

No suspected Ozone Depleting Substances (ODS) as mentioned in the European Regulation (EC) No 1005/2009
and the Commission decisions (EC) No 2003/160 and 2004/232 and related European Regulation (EC) 842/2006,
are used.

Chemical Weapons Convention (CWC)

The above product is not subject to reporting requirements under the Chemical Weapons Convention, dated
September 2005.

Declarable Substances Content

As reference for substances to be declared the following reference lists are used:

Global Automotive Declarable Substance List (GADSL)

This List is accessible under www.gadsl.org

International Electrotechnical Commission (IEC) 62474 List

This List is accessible under http://std.iec.ch/iec62474

All declarations are made vs. the Regulatory limits*, for which communication channels along the supply chain
exists or limits set as referred in the Specific Lists. For non regulated substances a general threshold limit of 0.1%
is applied. For any lower declaration limits, specific inquiries have to be made, which can be effort and time
intensive. If desired, specific customer testing can be discussed, subject to commercial agreements.

*Regulation (EC) No 1272/2008 on classification, labelling and packaging of substances and mixtures (CLP) and
amendments.

We do not routinely analyse our products for the substances mentioned on above reference lists, nor do we
require our raw material suppliers to do so. Our declaration is based on the intentionally addition during the
manufacture of the above product. To the best of our knowledge, these materials are not present as intentional
components in the raw materials used in the manufacture of this product except if stated.

Our declaration is based on the intentionally addition during the manufacture of the above product.
Except if differently stated and to the best of our knowledge, these materials are also not present as intentional
components in the raw materials used. However, we do not routinely analyze our resins for the substances
mentioned on above reference lists, nor do we require our raw material suppliers to do so.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 11 of 13

dupont.com
Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN
Groups of chemicals of concern not referenced by specific CAS numbers may be subject to interpretation,
therefore assessment has been carried out based on our understanding of such generic groups.

There are no substances intentionally added above the limits set by above regulatory standards.

Content of substances relevant to regulations

Please consult the Material Safety Data Sheet (SDS) or Article Information Sheet (AIS) relevant to your Region /
country. Due to differences in the applicable regulations, classifications and exposure limits, these may be
different from country to country.

Safety, Health, Environmental, Sustainability and Social Responsability

DuPont has a tradition going back over 200 years concerning its Safety, Health and Environmental policies. Our
occupational accident rates are one measurable result; they are far below the industry average.
DuPont applies the same philosophy to its products and operations for safety and environmental performance.

DuPont has committed itself to the RESPONSIBLE CARE® initiative of the Chemical Industry on a global basis. This
initiative is targeted towards a continuous improvement process in Safety, Health and Environmental
performance with measurable results.

All the DuPont polymer manufacturing and laboratory facilities are certified ISO 9001. Most of the DuPont
production locations have received the ISO 14001 certification or are actively working to obtain it. The certificates
are available on request for the specific products/production locations of interest.

Reports concerning the DuPont sustainability approach are published under

http://www.dupont.com/corporate-functions/our-approach/sustainability.html

The DuPont’s position towards social commitment can be found on

https://www.dupont.com/about/our-values.html

If you have further questions concerning DuPont or our products, please do not hesitate to contact your DuPont
representative.

® registered service marks of the American Chemistry Council, Inc.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 12 of 13

dupont.com
 Rynite® 935 BK505
THERMOPLASTIC POLYESTER RESIN

Regional Contacts:

United States, Canada Europe, Middle East Asia Pacific DuPont Apollo (Shenzhen)
and Latin America DuPont Specialty and Africa DuPont Specialty Products Limited
Products USA Operations Sàrl DuPont Apollo Hi-Tech Industrial Park,
Transportation & Advanced Polymers 2, chemin du Pavillon East Guangming Hi-Tech Zone,
Chesnut Run plaza CH-1218 Le Grand-Saconnex / Geneva Guangming New District,
P.O. Box 2915 Switzerland Shenzhen 518107, Guangdong, China
Wilmington, DE 19805 Tel. +41 22 717 5111 / Fax. 6602 Tel. +86 755 8949 5212 / Fax. 5251
USA
Tel. +1 302 999-3135

Disclaimer :

1. This statement is based on our current level of knowledge. This information is provided in good faith and is
believed accurate as the date of the document. It is based on a review of current formulation, composition,
manufacturing process and information supplied by vendors. No warranty is expressed or implied. Liability is
expressly disclaimed.
2. The data is not intended to substitute for any testing you may need to determine the suitability of this product
for a particular purpose.
3. This information is valid only for DuPont Polymer products as shipped from our facility, and may become invalid
if the product is mixed with other materials or otherwise altered.
4. Statements concerning the use of the products or formulations described herein are not to be construed as
recommending the infringement of any patent, copyright, designs or other intellectual property and no liability
for infringement arising out of such use is assumed by DuPont. None of this information is to be considered as a
license to operate under any patents.
5. For safety, health and environmental information please refer to the Material Safety Data Sheet which is the
primary source of information.

Issued: 22-Jun-2022 Revised: 24-Jan-2022 Page: 13 of 13

dupont.com

The information set forth herein is furnished free of charge, is based on technical data that DuPont believes to be reliable, and represents typical values that fall within the normal range of
properties. This information relates only to the specific material designated and may not be valid for such material used in combination with other materials or in other processes. It is
intended for use by persons having technical skill, at their own discretion and risk. This information should not be used to establish specification limits nor used alone as the basis of design.
Handling precaution information is given with the understanding that those using it will satisfy themselves that their particular conditions of use present no health or safety hazards and
comply with applicable law. Since conditions of product use and disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any
use of this information. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as a license to operate or a recommendation
to infringe on patents.
CAUTION: Do not use DuPont materials in medical applications involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided
from DuPont under a written contract or other acknowledgement that is consistent with the DuPont policy regarding medical applications and expressly acknowledges the contemplated use.
For further information, please contact your DuPont representative.
DuPont’s sole warranty is that our products will meet our standard sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to
refund of purchase price or replacement of any product shown to be other than as warranted. TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, DUPONT SPECIFICALLY DISCLAIMS
ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR NON-INFRINGEMENT. DUPONT DISCLAIMS LIABILITY FOR ANY SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

DuPont™, the DuPont Oval Logo, and all trademarks and service marks denoted with ™, SM or ® are owned by affiliates of DuPont de Nemours, Inc. unless otherwise noted.
© 2022 DuPont. All rights reserved.

Powered by TCPDF (www.tcpdf.org)