VIAVI Solutions

Data Sheet

VIAVI
3920B
Analog and Digital Radio Test Platform

General Specifications
RF Signal Generator <1% (1 kHz rate, 30 to 70% AM, 6 kHz deviation
THD
FM, 300 Hz to 3 kHz BW, Sine)
Frequency
Internal FM
10 MHz to 1.05 GHz (Standard) (Usable from 100
kHz) Deviation
Range ±0.001 to ±150 kHz, OFF
10 MHz to 2.7 GHz (392XOPT058) (Usable from 100 Range
kHz)
3% (From ±1 kHz to ±100 kHz deviation, 20 Hz to
Accuracy
Resolution 1 Hz 15 kHz rate)
Accuracy Frequency standard ±1 count Resolution 1 Hz
Output Level Deviation Rate 20 Hz to 20 kHz
T/R Port: -130.0 to -30 dBm (-30 dBm max for CW Internal AM
or FM; -35 dBm max for AM modulations; -40 dBm
Modulation
max for complex modulation) 0 to 100%
Range Range
GEN Port: -130.0 dBm to +10.0 dBm (+10 dBm max
for CW or FM; +5 dBm max for AM modulations; 0 1% (Modulation from 10% to 90% 20 Hz to 15 kHz
Accuracy
dB max for complex modulation) rate)
Resolution 0.1 dB Resolution 0.1%
1.0 dB for levels >-110 dBm (Typical better than 0.6 Rate 20 Hz to 20 kHz
dB) Internal SSB
Accuracy
1.5 dB for levels <-110 dBm (Typical better than 1.0
dB) Modulation
Upper SideBand (USB) or Lower SideBand (LSB)
Selection
Spectral Purity
Modulation
Residual FM <5 Hz (300 Hz to 3 kHz bandwidth) 0 to 100%
Range
Residual AM <0.1% RMS (300 Hz to 3 kHz bandwidth) Resolution 0.1%
<-25 dBc (Typically -30 dBc, RF level set at +10 Rate 300 Hz to 20 kHz
Harmonics
dBm)
External AM / FM / SSB
<-55 dBc (all freq. except Crossovers)
<-35 dBc (at 2nd order crossover frequency) With 1 Vrms, AM / FM / SSB have same
(10 MHz to 1 GHz: Crossover = 1400 MHz - Gen characteristics as internal sources, ±10% of
Non- Audio Inputs indicated setting. (Audio 1 or Audio 2 input from 20
freq.)
Harmonics Hz to 15 kHz [300 Hz to 3 kHz SSB] unbalanced). 8
(1 GHz to 2.7 GHz: Crossover = 3400 MHz - Gen
freq.) Vrms maximum modulation input level.
(Tracking Gen: Crossover = 3410.7 MHz - Gen freq.) With 50 mVrms, AM / FM / SSB have same
<-110 dBc / Hz @ 10 kHz offset, RF <500 MHz Microphone characteristics as internal sources, ±10% of
Phase Noise <-106 dBc / Hz @ 10 kHz ofset, RF <1000 MHz Input indicated setting. (MIC Input from 100 Hz to 15 kHz
<-95 dBc / Hz @ 10 kHz offset, RF >1000 MHz [300 Hz to 3 kHz SSB]).

Modulation Internal IQ Gen

OFF, AM, FM, FM50µs, FM75µs, FM750µs, AM USB, Sample Rate <1.89 Msamples / sec
Selections
AM LSB, IQGEN Size <3.8 million samples
Waveforms Sine, Square, Triangle, Ramp, DCS, DTMF Source File created by IQCreator
RF Receiver RF Error Meter
RF Receiver 0 to ±2.5 MHz from receiver frequency (6 MHz IF
Range
BW)
Demod AM, FM, FM50µs, FM75µs, FM750µs, AM USB, AM
Selections LSB Resolution 1 Hz
10 MHz to 1.05 GHz (Standard) (Usable from 100 Accuracy Frequency standard ±1 count
Frequency kHz)
T/R Port: -10 to +50 dBm
Range 10 MHz to 2.7 GHz (392XOPT058) (Usable from 100 Level Range
ANT Port: -60 to +10 dBm
kHz)
Signal CW, FM, AM <70% modulation
<-100 dBm (10 dB SINAD, FM, 25 kHz, 1 kHz rate,
6 kHz FM Deviation, 300 Hz to 3.4 kHz AF Filter, Demodulation Measurements
Pre-amp OFF) RF Characteristics
Sensitivity
<-113 dBm (10 dB SINAD, FM, 25 kHz, 1 kHz rate,
6 kHz FM Deviation, 300 Hz to 3.4 kHz AF Filter, 10 MHz to 1.05 GHz (Standard) (Usable from 100
Pre-amp ON) Frequency kHz)
Range 10 MHz to 2.7 GHz (392XOPT058) (Usable from 100
Demod Output Level kHz)
Nominally 1 Vrms (for deviation ±1/4 of selected T/R Port: -10 to +50 dBm
FM Input RF Level
BW; 25 kHz BW same output level as 30 kHz BW) ANT Port: -80 to +10 dBm
AM Nominally 2 Vrms (100% AM) Demod Counter
RF Measurements 20 Hz to 20 kHz (1 to 100 kHz FM Deviation, IF BW
RF Power Meter (Broadband) set appropriately for the received modulation BW)
Range
20 Hz to 10 kHz (30 to 90% AM, IF BW set
10 MHz to 1.05 GHz (Standard) (Usable from 2
appropriately for the received modulation BW)
Frequency MHz)
Range 10 MHz to 2.7 GHz (392XOPT058) (Usable from 2 Resolution 0.1 Hz
MHz) Accuracy ±50 ppm (±10 ppm typical)
Level Range 100 mW to 125 W (Usable from 10 mW) Waveform Sine or Square
Resolution 4 digits for W or 0.1 dB FM Deviation Meter
Accuracy 10%, 1 digit Range 0 to 150 kHz
Signal CW, FM, C4FM, 4FSK Resolution 10 Hz
RF Power Meter (Inband) ±3% plus source residual, ±1 count (1 to 150 kHz FM
10 MHz to 1.05 GHz (Standard) (Usable from 100 Accuracy deviation, IF BW set appropriately for the received
Frequency kHz) modulation BW)
Range 10 MHz to 2.7 GHz (Freq Ext Opt) (Usable from 100 Filter
kHz) Characteristic 0.01 dB (15 kHz low pass audio filter) above 20 Hz
T/R Port: -60 to +51 dBm Response
Lowest reading is receiver BW dependent Meter Flatness 0 dB
(Narrower bandwidths can measure lower levels)
Level Range 20 Hz to 20 kHz (IF BW set appropriately for the
ANT Port: -100 to +10 dBm FM Rate
Lowest reading is receiver BW dependent received modulation BW)
(Narrower bandwidths can measure lower levels) AM Deviation Meter
Resolution 0.1 dB Range 0 to 100%
±1 dB (Input level above minimum for selected BW Resolution 0.1%
Accuracy
[display not yellow], typically better than 0.6 dB)
±3% + source residual, ±1 count (30 to 90% AM, IF
AM Filter BW 6.25, 8.33, 10, 12.5, 25, and 30 kHz Accuracy BW set appropriately for the received modulation
FM Filter BW 6.25, 10, 12.5, 25, 30, 100, and 300 kHz BW)

Signal CW, FM, AM, C4FM, 4FSK, OPSK, QAM 20 Hz to 15 kHz (IF BW set appropriately for the
AM Rate
received modulation BW)
RF Counter
Audio and Modulation Measurements
10 MHz to 1.05 GHz (Standard) (Usable from 100
kHz, Auto-tune) Audio Input
Range Characteristics AF Counter, AF Level Meter, SINAD Meter,
10 MHz to 2.7 GHz (392XOPT058) (Usable from 100
kHz, Auto-tune) for the Distortion Meter, Hum and Noise Meter, Signal-to-
following Noise Meter
Resolution 1 Hz meters
Accuracy Frequency standard ±1 count Audio 1 or Audio 2 (unbalanced, chassis reference)
Front Panel
Level Range for T/R Port: -10 to +50 dBm (Find level is selectable) Audio 1 and Audio 2 (balanced, 600 Ω differential
Audio Inputs
Auto-tune ANT Port: -60 to +10 dBm (Find level is selectable) input)
Signal CW, FM, AM <70% modulation Hi-Z (>10 kΩ) - Unbalanced input
Audio Input 600 Ω - Unbalanced Input (8 Vrms MAX input)*
Impedance 600 Ω - Balanced input (Audio 1 and 2)
(Audio 1 and 2) *Note - 600 Ω unbalanced will auto-switch to Hi-Z
@ 8 Vrms

2 3920B Data Sheet

AF Counter Modes
Range 20 Hz to 20 kHz (usable from 10 Hz) Measure-
Stimulus Measure-
Mode Stimulus ment
Resolution 0.1 Hz Port ment Port
Input
Accuracy ±50 ppm max. ±10 ppm typical
RF Audio In 1
Wave shape Sine or square 1 TR / Gen AF Input
Generator or 2
Level Range AF Fctn Gen RF TR /
20 mV to 30 Vrms 2
(Audio) Generator Out Receiver Antenna
AF Level Meter Audio Filters (Characteristic Response)
Range 0 to 30 Vrms Filter Type Ripple -1 dB -60 dB
Volts: 1 mV (input <1 V) None No Filter
Resolution 10 mV (input >1 V)
<0.23 dB,
dBr, dBv, dBm: 0.01 dB
300 Hz Low-Pass above 20 330 Hz 590 Hz
Accuracy 5% (Unbalanced, Hi-Z, 300 to 3 kHz, 0.1 to 30 Vrms) Hz
Frequency <0.02 dB,
20 Hz to 20 kHz
Range 5 kHz Low-Pass above 20 5.5 kHz 6.7 kHz
SINAD Meter Hz

Range 0 to 60 dB <0.01 dB,

15 kHz Low-Pass above 20 16.1 kHz 17.8 kHz
Resolution 0.01 dB Hz
±1 dB, ±1 count (SINAD >3 dB, <40 dB, 5 kHz LP AF <0.01 dB,
Accuracy
filter) 20 kHz Low-Pass above 20 20.4 kHz 21 kHz
Frequency Hz
300 Hz to 5 kHz
Range 320 Hz / 60 Hz / 5.2
0.3 to 3.4 kHz Band-Pass <1.7 dB
Level Range 3.8 kHz kHz
0.1 to 30 Vrms
(Audio) 320 Hz / 60 Hz / 9.6
0.3 to 5 kHz Band-Pass <1.7 dB
Distortion Meter 5.2 kHz kHz

Range 0.0 to 100.0% 320 Hz / 60 Hz /

0.3 to 15 kHz Band-Pass <1.7 dB
16.1 kHz 19.9 kHz
Resolution 0.1%
200 Hz / 60 Hz / 21
<±0.5% (Distortion 1 to 10%, 5 kHz LP AF Filter) 0.3 to 20 kHz Band-Pass <1.7 dB
Accuracy 20.4 kHz kHz
<±1.0% (Distortion 10 to 20%, 5 kHz LP AF Filter)
Per C-MSG Per C-MSG Per C-MSG
Frequency PSOPH C-MSG Band-Pass
300 Hz to 5 kHz Spec Spec Spec
Range
Per CCITT Per CCITT Per CCITT
Level Range PSOPH CCITT Band-Pass
0.1 to 30 Vrms Spec Spec Spec
(Audio)
300 Hz High-Pass <1.7 dB 320 Hz 60 Hz
Hum and Noise
Audio Function Generator(s)
Range -100 dB to 0 dB
Sine, Square, Triangle, Ramp, Digital Coded Squelch,
Resolution 0.01 dB Wave Shape
DTMF
Accuracy ±1 dB, ±1 count (>-60 dB, <-20 dB) Frequency
Signal Sine: 20 Hz to 40 kHz (usable from 1 Hz to 40 kHz)
300 Hz to 5 kHz
Frequency Range Square, Triangle and Ramp: 20 Hz to 4 kHz (usable
Audio Input 1 Hz to 40 kHz)
0.1 to 30 Vrms
Level Resolution 0.1 Hz
T/R Port: -10 to +50 dBm Accuracy ±50 ppm, ±10 ppm typical
RF Intput Level
ANT Port: -80 to +10 dBm
Level
Signal-to-Noise Ratio
Range 1 mV to 5 V RMS into a 10 kΩ load
Range -100 to 0 dB
Resolution 0.1 mV
Resolution 0.01 dB
Accuracy ±1% of setting (10 kΩ load)
Accuracy ±1 dB, ±1 count (>-60 dB, <-20 dB)
Impedance <10 Ω
Signal
300 Hz to 5 kHz <0.5% (1 kHz, 5 Vrms, 80 kHz BW, 10 kΩ load, Sine)
Frequency
Spectral Purity <1.0% (Typical, 20 Hz to 20 kHz, 100 mV to 5 Vrms,
Audio Input 80 kHz BW, 10 kΩ load, Sine)
0.1 to 30 Vrms
Level
T/R Port: -10 to +50 dBm
RF Input Level
ANT Port: -80 to +10 dBm

3 3920B Data Sheet

Oscilloscope Ohmeter
Display Full Scale 200 ohms, 2 kohms, 20 kohms, 200 kohms, 2
Range Mohms, 20 Mohms, Auto
Traces 2
Maximum
Trace Types Live, captured, accumulated 30 Vrms referenced to common or earth ground,
Open Circuit
Markers 2 Category I
Input Voltage
Marker Time with amplitude, deviation or % depth Resolution 3-½ digits (2000 counts)
Functions Delta marker (including 1/∆ t, e.g. Hz)
Accuracy ±5% Full Scale ±1 count
Vertical
External Current Shunt (Optional)
3 dB
16 MHz Rating 10 amps, 100 mV
Bandwidth
(Category II) 20 amps - ON 1 minute, OFF 4 minutes
Frequency
DC to 4 MHz (40 MS / s sampling rate) Accuracy (18o
Range DC to 10 kHz: ±0.25%
to 28o C)
Input Range 0 to 100 Vpeak Max, Category II
Temperature
2 mV to 20 V / division in a 1, 2, 5 sequence (8 [h] x 0.005% / o C
Scales Coefficient
10 [w] graticule display)
RF Spectrum Analyzer
5% of full scale (DC to 1 MHz)
Accuracy Frequency
10% of full scale (1 to 4 MHz)
10 MHz to 1.05 GHz (Standard) (Usable from 100
Resolution Better than 1% of full scale
kHz)
Coupling DC, AC, GND Range
10 MHz to 2.7 GHz (392xOPT058) (Usable from 100
Horizontal kHz)

Sweep Factors 1 µSec to 1 Sec / division in a 1, 2, 5 sequence Resolution 1 Hz

Accuracy >1.5% of full scale Accuracy Same as frequency standard

Resolution >1% of full scale Span

Input Mode Start / Stop, Center / Span, and Zero Span

1 MΩ, 20 pF
Impedance Selection list is 2 kHz to Full Span in a 1, 2, 5
Trigger Range sequence, plus Zero Span (Span may be entered
numerically down to 1 Hz resolution)
Trace A, Trace B, EXT, (or Trace C with no CH1 or
Trigger Source Display Span Accuracy + Frequency Accuracy + 50% of
CH2 Input)
Accuracy RBW
Trigger Edge Rising / falling
Span Accuracy ±1% of span width
Auto / normal
Trigger Mode Marker
Continuous / single shot ±1% of span width
Accuracy
External Hi-Z BNC input on the rear panel of the unit
Trigger Level Adjustable from -5 to +5 V Level

Digital Multimeter Ref Level T/R Port: -50 to +50 dBm

Range ANT Port: -90 to +10 dBm
AC / DC Voltmeter
Vertical Scales 1, 2, 5, 10 dB / division
Full Scale 200 mV, 2 V, 20 V, 200 V, 2000 V, Auto
Range (150 VAC RMS or VDC MAX input Category II) Reference Level
0.1 dB
Resolution
Resolution 3-½ digits (2000 counts)
Ref Level Units dBm
DC ±1% Full Scale ±1 count
Accuracy Dynamic 70 dB (Antenna, no attenuation, Ref Level -30 dBm,
AC ±5% Full Scale ±1 count
Range 30 kHz RBW)
AC Volts
Frequency 50 Hz to 10 kHz Bandwidth
±1 dB (After Normalize)
Range Switching Error

AC / DC Ammeter ±1 dB (RBW: 3 kHz, 30 kHz, 60 kHz, 300 kHz, 6

Log Linearity MHz)
Full Scale 200 mA, 2 A, 20 A, Auto (20 A range uses optional ±1 dB (300 Hz RBW typical)
Range shunt connected to Voltmeter)
±1 dB (Input signal -10 dB from Ref Level,
Maximum Accuracy
30 Vrms referenced to common on earth ground, Normalized, preamp off)
Open Circuit
Category I Attenuator 0 to 50 dB of attenuation, controlled by changing
Input Voltage
Selections the Ref Level
Resolution 3-½ digits (2000 counts)
3rd Order
Accuracy ±5% Full Scale ±1 count -60 dBc (Input Level of -30 dBm, Ref Level at -20
Intermod-
dBm)
AC Volts ulation
Frequency 50 Hz to 10 kHz Harmonic -55 dBc (Input Level of -30 dBm, Ref Level at -20
Range Spurious dBm)

4 3920B Data Sheet

 Level - Continued Spurious Level
Non-Harmonic -60 dBc (Input Level of -30 dBm, Ref Level at -20 Range 0 to -60 dBc
Spurious dBm)
Resolution 0.1
Displayed
-125 dBm (Typical, 300 Hz RBW, ANT Port Accuracy Same as RF Spectrum Analyzer
Average Noise
terminated, 20 sweep average) Audio Spectrum Analyzer (Optional)
Level (DANL)
Resolution Bandwidth Frequency
RBW Selections 300 Hz, 3 kHz, 30 kHz, 60 kHz, 300 kHz, 6 MHz Range Start and Stop Frequency - 0 Hz to 24,000 Hz
RBW 60 dB / 3 Resolution 1 Hz
>10:1
Filter Shape Accuracy ±50 ppm (±10 ppm Typical)
Selectivity - Span 2 kHz min to 24 kHz max
60 dB / 3 dB ratio better than 10:1
Filter Shape
Level
±10% of RBW for 3 kHz, 30 kHz, 60 kHz, 300 kHz
Accuracy -10% / +25% of RBW for 6 MHz Vertical Scales 1, 2, 5, 10, 20 dB per division
±20% of RBW for 300 Hz Reference Level 0 dB Full Scale (dBr)
Bandwidth Dynamic
±1 dB Greater than 120 dB
Switching Error Range
Video Bandwidth Accuracy ±1 dB from 300 Hz to 15 kHz
Range 10 Hz to 1 MHz in a 1, 3, 10 sequence, plus NONE Markers
Sweep Number of
2
Frequency Markers
100 mS to 100 S in a 1, 2, 5 sequence
Sweep Time Frequency Standard I/O
Zero Span Internal Frequency Standard Output
50 mS to 100 S in a 1, 2, 5 sequence
Sweep Time
Frequency 10 MHz (nominal)
Sweep Trigger
Internal and External Output Level 1 Vpp (nominal) into 50 Ω
Source
Trigger Modes Continuous (repeat), single (single-shot) Temperature
Stability (0 to ±0.01 ppm
Function / Feature 50o C)
Display Modes Live, average, max hold Aging Rate ±0.1 ppm / year after 1 month continuous use
Averages 1 to 100 Warm Up Time Less than 5 min. to ±0.02 ppm
Markers External Frequency Input
Track Frequencies (or time) and amplitudes Frequency 10 MHz
Number of 1 to 5 Vpp for sine waves
8 Input Level
Markers 3.3 / 5 V TTL for square waves
Marker to Peak Connector BNC socket (10 kΩ Input / 50 Ω Output)
Marker to Next Right / Left
Marker to Minimum Input / Output Connectors
Marker
Marker to Ref Level ANT (RF Input)
Functions
Marker to Center Frequency
Connector Type TNC
Marker sets Span
Marker sets Vertical Scale (Zero Span only) Function Receiver input
Tracking Generator (Optional) Impedance 50 Ω (nominal)
Refer to RF Signal Generator section for: VSWR (with
Tracking Better than 1.44:1 (RF freq. <1.05 GHz)
-Frequency range and accuracy Attenuation
Generator Better than 1.58:1 (RF freq. >1.05 GHz to <2.7 GHz)
-Output level range, resolution, and accuracy <10 dB)
Output
- Spectral purity
Input 10 W with warning above +17 dBm (Remove power
Span and Protection immediately when alarm sounds)
Same as Spectrum Analyzer
Sweep Time
Gen (RF Output)
Tracking
Connector Type TNC
Generator Output port selection, RF level, Reference cal
Controls Function Generator high-level output
Harmonics and Spurious (Optional) Impedance 50 Ω (nominal)
Harmonic Level VSWR (with Better than 1.7:1 (RF freq. <1.05 GHz)
level <0 dBm) Better than 1.9:1 (RF freq. >1.05 GHz to <2.7 GHz)
Range 0 to -60 dBc
Input 10 W with warning above +23 dBm (Remove
Resolution 0.1
Protection power immediately when alarm sounds)
Accuracy Same as RF Spectrum Analyzer

5 3920B Data Sheet

T/R (RF Input / Output) Mains Supply
50 Hz to 60 Hz ±5%
Frequency
Connector Type Type N
Power
Function RF power input, generator low-level output Nominally 120 W (200 W Max)
Consumption
Impedance 50 Ω (nominal)
Fuse
Better than 1.2:1 (RF freq. <1.05 GHz) 3 A, 250 V, Type F
VSWR Requirements
Better than 1.3:1 (RF freq. >1.05 GHz to <2.7 GHz)
Environmental / Safety
200 W with warning above 135 W or power
Operating 0 to 50� C (Tested in accordance with MIL-PRF-
termination temp >100o C. Recommended max
Input Temperature 28800F Class 3)
of 30 s ON and minimum of 2 min OFF for power
Protection
levels above 50 W. (Remove power immediately Warm-up Time 15 minutes
when alarm sounds)
Storage -40 to +71� C (Tested in accordance with MIL-PRF-
GPIB Temperature 28800F Class 3)
Connector Type 24 pin IEEE 80% up to 31� C decreasingly linearly to 50% at
Relative
40� C (Tested in accordance with MIL-PRF-28800F
Function IEEE-488, 1-1997 Humidity
Class 3)
Ethernet
Altitude 4,000 m (13,123 ft) (MIL-PRF-28800F Class 3)
Connector Type 8 position, RF-45 100 / 10 Mbit / s
30 G Shock (functional shock)
Function 10 / 100 Base-T network connection Shock and
5-500 Hz random vibrations (Tested in accordance
Vibrations
RS-232 with MIL-PRF-28800F Class 3)

Connector Type 9-pin, D-sub, Male Use Pollution degree 2

300, 600, 1200, 2400, 4800, 9600, 19.2k, 38.4k, 57.6k, EMC EN 61329, Class 2
Baud Rates
115.2k >8,000 hour calculated MTBF (MIL-HDBK-217F,
Reliability
Stop Bits 1 or 2 notice 2)

Parity Odd, even, none UL 6101B-1

Safety
EN 61010-1
Video Standards
CSA C22.2 No.61010-1
Connector Type 15-pin, D-sub, VGA Dimensions and Weight
Function VGA for external monitor Height 7.75" (19.7 cm)
IF Output Width 14" (35.6 cm)
Connector Type BNC Depth 18.5" (47.0 cm)
Function 10.7 MHz Receiver IF Weight 36.8 lbs (16.5 kg)
Output Level Proportional to Receive Signal Level General Characteristics
Mic / Accessory LCD Display 6.4” diagonal
Connector Type 8 position, female DIN Screen Size 162.6 mm diagonal

Microphone connection, modulation input, demod 5.1” (h) x 3.8” (v)

Function Active Area
output, PTT operation 129.6 mm (h) x 97.44 mm (v)

Parallel Port Resolution 640 x 480 pixels

Connector Type 25 position, female D-sub Internal 30 GByte hard disk available for user
Disk Storage
storage
Function Printer interface
USB P25 (Optional System)
Twin USB standard connection (rear panel) RF Signal Generator
Connector Type
Single USB standard connection (front panel)
Frequency
Function IEEE-488, 1-1997
Range 10 MHz to 1.05 GHz (Standard) (Usable from
Test Port 100 kHz)
Connector Type 15 position, female 3 tier D-sub 10 MHz to 2.7 GHz (392XOPT058) (Usable
from 100 kHz)
Programmable I/O and voltage output (optional
Function Resolution 1 Hz
interface)
Auxiliary IF Input Accuracy Frequency standard ±1 count

Connector Type High-density dual inline Output Level

Function External digital receiver input (optional interface) Range T/R Port: -138.0 to -30.0 dBm for C4FM and
H-CPM modulations (-40.0 for all other
AC Power Requirements modulations)
Mains Supply GEN Port: -130.0 to +10.0 dBm for C4FM and
110 V to 220 VAC ±10% H-CPM modulations (+0.0 dBm for all other
Voltage
modulations)

6 3920B Data Sheet

 Resolution 0.1 dB Constellation Line graph of the deviation at the symbol
point.
Accuracy 1.0 dB for levels >-110 dBm (Typical better
than 0.6 dB) Distribution Graph of the statistical distribution of the
1.5 dB for levels <-110 (Typical better than deviation at the symbol point. This is a
±1.0 dB) graph of the deviation at the symbol point
versus the percentage of occurrence of that
Modulation C4FM, CQPSK, LSM
deviation.
Test Patterns STD 1011, STD CAL, STD SILENCE, STD
Eye Diagram Graph of the demodulated signal versus
INTFR, STD BUSY, STD IDLE, STD 511 (0.153),
time, synchronized with the symbol points.
STORED SPCH, VOICE, 1011, SILENCE
The number of symbol periods is selectable.
RF Receiver Range is 2 to 16.
Frequency Range 10 MHz to 1.05 GHz (Standard) (Usable from Trajectory Graph of the demodulated signal in the
100 kHz) complex domain. This graph shows the
10 MHz to 2.7 GHz (392XOPT058) (Usable Inphase versus the Quadrature phase of the
from 100 kHz) demodulated C4FM, CQPSK, or LSM signal.
Resolution 1 Hz Protocol
Level Range T/R Port: -10 to +50 dBm Data Link
ANT Port: -60.0 to +10 dBm (with preamp
Header MFID, ALG, KEY, TGID, MI
-63)
Voice Frame Frame #, NAC, DUID, KEY, ALG, MI, RAW,
P25 Measurements
LCO, Protect, SF, EMG, LSD, STS, STS 2
Modulation Fidelity
Conventional Mode NAC, Call Type, TGID, UID, Alg ID, Key ID
Range 0 to 20% Simulation
Resolution 0.1% Phase I Trunking Simulation
Accuracy <5.0% of reading (2.5 to 10%) System Plans Basic 800, Basic UHF, Basic VHF, Basic 700,
plus multiple user defined
Symbol Deviation
User Defined Fields System ID, WACN, RFSS ID, Site ID,
Range 1500 Hz to 2100 Hz
Announcement Group Address, Local
Resolution 0.1 Hz Registration Area, Service Class, Active
Accuracy ±10 Hz (1620 to 1980 Hz) Network, Local / Global Affiliation, Group
Affiliation, Registration, WGID Mapping,
Symbol Clock Error WUID mapping, Protected 16 Channel IDs
Range ±100 mHz with Base Frequency, Bandwidth, TX Offset,
Channel Spacing
Resolution 0.01 mHz
Trunking Control Base Simulation sets System Plan, Implicit
Accuracy 1 ppm (±4.8 mHz) / Explicit mode, Control Channel ID / NUM
Frequency Error / Frequency, Control Channel power level,
Control Channel modulation, Traffic Channel
Range ±4000 Hz
ID / NUM / Frequency, Traffic Channel
Resolution 0.01 Hz power level, Traffic Channel modulation
Accuracy Frequency Standard ±1 count Simulator Call Type, TGID, UID, Alg ID, Key ID
UUT TX / RX Bit Error Rate Encryption Supports DES Encryption (AES available
with restrictions)
Range 0 to 20%
Resolution 0.1% DMR (Optional System)
Signal Power RF Signal Generator
Range T/R Port: -60 to +51 dBm Frequency
ANT Port: -100 to +10 dBm
10 MHz to 1.05 GHz (Standard) (Usable from
Resolution 0.1 dB 100 kHz)
Range
Accuracy ±1 dB (typically better than ±0.6 dB) 10 MHz to 2.7 GHz (392XOPT058) (Usable
from 100 kHz)
Error Vector Magnitude
Resolution 1 Hz
Range 0 to 20%
Accuracy Frequency standard ±1 count
Resolution 0.01%
Output Level
Carrier Feedthrough
T/R Port: -130.0 to -40.0 dBm
Range 0 to -80.00 dB Range
GEN Port: -130.0 to +0.0 dBm
Resolution 0.01 dB Resolution 0.1 dB
Graphical Displays 1.0 dB for levels >-110 dBm (Typical better
Modulation Fidelity Displays than 0.6 dB)
Accuracy
1.5 dB for levels <-110 (Typical better than
1.0 db)

7 3920B Data Sheet

Modulation 4-FSK 10 MHz to 1.05 GHz (Standard) (Usable from
100 kHz)
STD IB 1031, STD IB CAL, STD IB 511 (0.153), Range
Test Patterns 10 MHz to 2.7 GHz (392XOPT058) (Usable
STD OB TSYNC (Repeater IDLE pattern)
from 100 kHz)
RF Receiver
Resolution 1 Hz
Frequency Range
Accuracy Frequency standard ±1 count
10 MHz to 1.05 GHz (Standard) (Usable from
100 kHz) Output Level
Range
10 MHz to 2.7 GHz (392XOPT058) (Usable
T/R Port: -138.0 to -30.0 dBm for 4FSK
from 100 kHz) Range
GEN Port: -130.0 to +10.0 dBm for 4FSK
Resolution 1 Hz
Resolution 0.1 dB
T/R Port: -10 to +50 dBm
1.0 dB for levels >-110 dBm (Typical better
Level Range ANT Port: -60.0 to +10 dBm (with preamp
than 0.6 dB)
-63) Accuracy
1.5 dB for levels <-110 (Typical better than
DMR Measurements 1.0 dB)
FSK Error Modulation 4FSK
Range 0 to 20% Test Patterns STD 511 (0.153)
Resolution 0.01% RF Receiver
Accuracy <5% of reading (2.5 to 10%) 10 MHz to 1.05 GHz (Standard) (Usable from
100 kHz)
Symbol Deviation Frequency Range
10 MHz to 2.7 GHz (392XOPT058) (Usable
Range 1500 Hz to 2350 Hz from 100 kHz)
Resolution 0.1 Hz Resolution 1 Hz
Accuracy ±10 Hz (1745 to 2140 Hz) T/R Port: -10 to +50 dBm
Symbol Clock Error Level Range ANT Port: -60.0 to +10 dBm (with preamp
-63)
Range ±1000 mHz
dPMR Measurements
Resolution 0.01 mHz
FSK Error
Accuracy 1 ppm (-48 to +48 mHz)
Range 0 to 20%
Frequency Error
Resolution 0.01%
Range ±4000 Hz
Accuracy <5.0% of reading (2.5 to 10%)
Resolution 0.01 Hz
Symbol Deviation Meter
Accuracy Frequency Standard ±1 count
Range 875 Hz to 1225 Hz
Magnitude Error
Resolution 0.1 Hz
Range 0 to 5%
Accuracy ±10 Hz (945 to 1155 Hz)
Resolution 0.01%
Symbol Clock Error Meter
Accuracy <10% of reading (0 to 2%)
Range ±1000 mHz
UUT TX / RX Bit Error Rate
Resolution 0.01 mHz
Range 0 to 20%
Accuracy 1 ppm (-24 to +24 mHz)
Resolution 0.1%
Frequency Error
Signal Power / Slot Power
Range ±4000 Hz
T/R Port: -60 to +51 dBm
Range Resolution 0.01 Hz
ANT Port: -100 to +10 dBm
Resolution 0.1 dB Accuracy Frequency Standard ±1 count

Accuracy ±1 dB (typically better than ±0.6 dB) UUT TX BER Meter

Protocol Range 0 to 20%

Decode Color Code, Call ID, Unit ID Resolution 0.1%

Accuracy Color Code, Call ID Signal Power Meter

T/R Port: -60 to +51 dBm
Range
ANT Port: -100 to +10 dBm
dPMR (Optional System)
Resolution 0.1 dB
RF Signal Generator
Accuracy ±1 dB (±0.6 dB typical)
Frequency

8 3920B Data Sheet

Graphical Displays RF Receiver
Modulation & Power Analysis 10 MHz to 1.05 GHz (Standard) (Usable from
100 kHz)
Line graph of the deviation at the symbol Frequency Range
Constellation 10 MHz to 2.7 GHz (392XOPT058) (Usable
point.
from 100 kHz)
Graph of the statisitcal distribution of the
T/R Port: -40 dBm to +40 dBm
deviation at the symbol point. This is a Level Range
ANT Port: -80 dBm to 0 dBm
Distribution graph of the deviation at the symbol point
versus the percentage of occurrence of that MS: Control Burst (CB), Normal Uplink Burst
deviation. (NUB)
BS: Normal Downlink Burst (TS1+2, TS1, and
Graph of the demodulated signal versus Burst Types
TS2)
time, synchronized with the symbol points.
Eye Diagram Synchronization Burst, PRBS with no
The number of symbol periods is selectable.
training sequence
Range is 2 to 16.
TETRA Measurements
Displays the power measurement of the
Power Over Time received signal over a specified period of Average power across the useful part of
time; indicating the transmitter’s stability POWER the burst measured at the symbol points
through a TETRA filter

TETRA (Optional System) Resolution 0.1 dB

RF Signal Generator Accuracy ±1.0 dB (±0.6 dB typical)

Frequency Modulation accuracy measures the

MODULATION
displacement of symbol points from their
10 MHz to 1.05 GHz (Standard) (Usable from ACCURACY
ideal position
100 kHz)
Range 20.0% RMS vector error
10 MHz to 2.7 GHz (392XOPT058) (Usable
from 100 kHz) Range 40.0% Peak vector error
20.0% Residual carrier
Resolution 1.0 Hz
Resolution 0.1%
Accuracy Frequency Standard ±1 count
Accuracy ±0.5% at 10% error
Output Level
Timing error relative to downlink results
T/R Port: -130.0 to -40.0 dBm BURST TIMING ERROR available for avg max, min and worst case
Range
GEN Port: -130.0 to 0 dBm for a sample of up to 250 bursts
Resolution 0.1 dB Range ±510.0 symbols
1.0 dB for levels >-110 dBm (Typical better Resolution 0.01
than 0.6 dB)
Accuracy Accuracy ±0.05 symbols
1.5 dB for levels <-110 (Typical better than
1.0 dB) Timing offset range ±999.99 symbols
Modulation Frequency Error
π/4 DQPSK, 18 ksymbols / sec, TETRA filter Range ±500.0 Hz
Type
(RRC with <0.35)
Resolution 0.1 Hz
<3% RMS
Accuracy Accuracy ±15 Hz +frequency standard accuracy
<6% peak
Residual Carrier Power <-35 dBc BER Testing (TETRA
BER, MER, and PUEM
MS T1 mode)
Test Signals
BER Testing (TETRA
Main Control Channel (MCCH) Traffic BER, RBER, and MER
MS mode)
Channel (TCH / S) containing silence or
TETRA MS BER Testing (TETRA
1 kHz tone or talk-back, Fast Associated BER, MER, and PUEM
Control Channel (FACCH) BS T1 mode)

T1 test signals (in accordance with ETSI EN Graphical Displays

300 394-1) Modulation & Power Analysis
T1 type 7 (TCH / 7.2), T1 type 2 (SCH / F), T1
TETRA MS T1 Line graph of the deviation at the symbol
type 3 (BSCH + SCH / HD), T1 type 4 (TCH Constellation
point.
/ 2.4), T1 type 15 (TCH / S), T1 type 17 (TCH
/ 4.8) Graph of the statisitcal distribution of the
deviation at the symbol point. This is a
T1 test signals (in accordance with ETSI EN
Distribution graph of the deviation at the symbol point
300 394-1)
versus the percentage of occurrence of that
T1 type 7 (TCH / 7.2), T1 type 8 (SCH / F), T1
TETRA BS T1 deviation.
type 9 (STCH + STCH UL), T1 type 10 (TCH /
2.4), 18 Frame PRBS.
Framed PRBS, Unframed PRBS
Traffic Channel (TCH / S) containing silence
TETRA DM
or 1 kHz tone or talk-back

9 3920B Data Sheet

 Graph of the demodulated signal versus Mobile parameter control for SSI, GSSI,
time, synchronized with the symbol points. power class, receiver class
Eye Diagram
The number of symbol periods is selectable. Registration, test mode registration and
Range is 2 to 16. de-registration
Private (individual) call, group call, phone
Displays the power measurement of the
call, emergency call, user defined call
Power Over Time received signal over a specified period of
(mobile terminated)
time; indicating the transmitter’s stability
Call timer and trunking type selection
Graphical Displays Cell re-selection (requires two test sets and
Display of power versus time for a a power splitter)
complete burst or ramp up / ramp down Signaling Functions Short data service
intervals measured at the symbol points Status message and SDS types 1 to 4 call
POWER PROFILE control (simplex calls)
and displayed relative to a TETRA mask
DISPLAY Power control and Frequency control
(TETRA limits are user defined) with pass /
fail indication. Measured through a TETRA Frequency handoff
filter referenced (0 dB) to average power. RF loopback control (TT)
Display of mobile information
Dynamic Range 70 dB Demodulated and channel decoded data
Vertical Scale 2 dB / div or 0.1 dB / div in 1, 2, 5 steps Protocol history display
Talk back, silence and test tone (1 kHz
±1.0 dB (±0.6 dB typical) at symbol points digitally encoded)
Accuracy
for levels greater than -10 dB
Polar display of amplitude versus phase at
the symbol point measured over all symbols
CONSTELLATION (SN0 ~ SN max) through a TETRA filter. Also
DISPLAY available as a rotated constellation display
where all symbol point values are mapped
to a single constellation point. Ordering Information
Polar display of amplitude versus phase
PHASE TRAJECTORY
continuously measured over the duration Versions and Options
DISPLAY
(SN0 ~ SN max) through a TETRA filter.
Order Number Description
Graphical Displays - Continued
91164 3920B Analog and Digital Radio Test Platform
Vector error (%), magnitude error (%), and
VECTOR ANALYSIS phase error (degrees) measured at symbol Standard Accessories
DISPLAY points (SN0 ~ SN max) through a TETRA
Front / Rear Cover
filter.
Vector error 0.1% / div to 20% / div in 1, 2, Adapter (BNC-F to TNC-M x2)
5 steps Adapter (N-M to BNC-F)
Phase error ±0.1o / div to ±20o / div in 1, 2,
Vertical Scaling AC Line Cord
5 steps
Magnitude error ±1.0% / div to ±20% / div Antenna (BNC) (450 MHz)
in 1, 2, 5 steps
Antenna (BNC) (800 MHz)
TETRA Channel Plans and Signaling
Antenna (BNC) (150 MHz)
TETRA 380-400 (0 Hz or 12.5 kHz offset)
TETRA 410-430 (0 Hz, 6.25 kHz, or 12.5 kHz 112265 3920B Digital Radio Test Set FAA
offset)
Channel Plans TETRA 450-470 (0 Hz or 12.5 kHz offset) 88459 3920N Digital Radio Test Set
TETRA 805-870 (0 Hz or 12.5 kHz offset)
TETRA 870-921 (0 Hz or 12.5 kHz offset) 89871 3920N Test Accessory Kit
No plan and user defined
Options
Mobile County Code, MCC
83352 390XOPT051 Site Monitoring Applications
Mobile Network Code, MNC
System Identify
Base Color Code, BCC 83353 390XOPT054 IQ Gen Modulation
Location Area Code, LA
83354 390XOPT055 Audio Analyzer

83368 390XOPT210 Analog Simulcast Option (Requires

Opt055)
83390 392XOPT058 2.7 GHz Frequeny Range Extension
Option
83356 390XOPT060 Harmonics & Spurious
Measurements

83357 390XOPT061 Tracking Generator

83358 390XOPT064 Analog Duplex Power Between

Markers

10 3920B Data Sheet

92573 390XOPT067 POCSAG Auto-Test and Alignments

83359 390XOPT110 TETRA MS (Mobile Station Testing) Analog Radios

83362 390XOPT114 TETRA Energy Economy Mode 83355 390XOPT059 Auto-Test II Environment for Analog
(Requires Opt110) Radio Systems
83360 390XOPT111 TETRA BS (Base Station Testing) 83387 390XOPT603 TIA / EIA-603 FM Land Mobile Test
Software (Requires Opt059)
83361 390XOPT112 TETRA DM (Direct Mode Testing)
138575 390XOPT624 Collins Aerospace 721S Blade Auto-
83363 390XOPT200 P25 Conventional Operation (with Test (Requires Opt059, 061)
DES OFB Type III)
TETRA Radios
83364 390XOPT201 P25 Trunking Operation VHF / UHF /
700 / 800 MHz (Requires Opt200) 85543 390XOPT115 Auto-Test II Environment for TETRA
Radio Systems
83369 390XOPT212 Explicit Mode Trunking (UHF / VHF
only) (Requires Opt201) 90676 390XOPT611 Motorola TETRA MS Auto-Test
Software - Includes Opt054 as standard (Requires
83370 390XOPT213 Unit to Unit Call (Requires Opt212)
Opt110, 115)
83371 390XOPT214 Adjacent Channel Broadcast Message
90943 390XOPT621 Motorola TETRA MTS (Requires
(Requires Opt201)
Opt115, 111)
83372 390XOPT215 Secondary Control Channel Broadcast
Message (Requires Opt201) P25 Radios

84412 390XOPT260 P25 Performance Test Triggers 83373 390XOPT218 Auto-Test II Environment for P25
(Requires Opt200 and Opt201) Radio Systems (Requires Opt200)

83365 390XOPT204 LSM Generate and Receive / Analysis 87371 390XOPT607 BK Technologies DPHX5102X Series
(Requires Opt200) Auto-Test and Alignment Software (Requires
Opt218, 061)
83366 390XOPT206 P25 Control Channel Logger Option
(Requires Opt200) 91956 390XOPT627 BK Technologies KNG Command
Series Auto-Test and Alignment Software;
82566 390XOPT230 Off Air Monitor Software for P25 Portables Only (Requires Opt218, 061)
Message Logging - Protocol Analysis Tool (Requires
Opt206) 139148 390XOPT636 BK Technologies KNG S-Series
(Portables only) Auto-Test and Alignment Software
83367 390XOPT207 SMARTNET / SmartZone Option
(Requires Opt218, 061)
(Requires Opt200)

62377 390XOPT209 KVL 3000 & 4000 Keyloader Option 87372 390XOPT606 EF Johnson ES Series Auto-Test and
(Requires Opt200) Alignment Software (Requires Opt218, 061)

90532 390XOPT220 Phase 2 Two-Slot Time Division 112997 390XOPT633 EF Johnson Viking Series Auto-Test
Multiple Access Physical Layer (Requires Opt200) and Alignment Software (Requires Opt218, 061)

67444 390XOPT240 P25 AES Encryption (Requires 90966 390XOPT616 L3Harris P25 Series Auto-Test and
Opt200) Alignment Software (Requires Opt218, 061)

83378 390XOPT250 Occupied Bandwidth for P25 91955 390XOPT625 L3Harris P25 ADVANCED Series Auto-
(Requires Opt200) Test and Alignment Software (Requires Opt616)

83383 390XOPT400 DMR (MOTOTRBO) ETSI 102-361 140637 390XOPT637 L3Harris XL Series Auto-Test and
Alignment Software (Requires Opt218, 061)
84413 390XOPT402 DMR XML Channel Logger Option
(Requires Opt400) 87370 390XOPT605 Icom P25 Auto-Test and Alignment
Software (Requires Opt218, 061)
84414 390XOPT420 dPMR - ETSI 102-658
90946 390XOPT608 Kenwood 5x10 Series Auto-Test and
90533 390XOPT422 dPMR Control Channel Logger Option
Alignment Software (Requires Opt218, 061)
(Requires Opt420)
91959 390XOPT630 Kenwood 5x20 Series Auto-Test and
84416 390XOPT440 NXDN
Alignment Software (Requires Opt218, 061)
104218 390XOPT442 NXDN XML Channel Logger (Requires
141437 390XOPT641 Kenwood Viking 5/6/7000 Series
Opt440)
Auto-Test and Alignment Software (Requires
84418 390XOPT460 ARIB T98 Opt218, 061)
140219 390XOPT462 ARIB T98 Channel Logger (Requires 83385 390XOPT600 Motorola ASTRO 25 XTS / XTL Series
Opt460) Auto-Test and Alignment Software (Requires
Opt218, 061)

84422 390XOPT602 Motorola ASTRO 25 Series XTL Power

Auto-Test and Alignment Software (Requires
Opt600 & 112277)

11 3920B Data Sheet

83386 390XOPT601 Motorola ASTRO (XTS-3000) Series Optional Accessories
Auto-Test and Alignment Software (Requires 89243 Case, Hard Transit with Wheels (Pelican)
Opt21, 061)
10225 Case, Soft Padded Carrying
84421 390XOPT604 Motorola APX Series Auto-Test and
10228 3920 Accessory Pouch
Alignment Software (Requires Opt218, 061 &
112277) 63936 DMM Test Leads (Category 3 Rated)
112277 10 Amp Current Shunt (0.01 Ohm)
140545 390XOPT644 Motorola APX 8000 Series Auto-Test
and Alignment Software (Requires Opt604) 90323 3920 5U Rack Mount Kit

140899 390XOPT645 Motorola APX “B” Series Auto-Test 90322 3920 6U Rack Mount Kit
and Alignment Software (Requires Opt604) 67442 Kit, 10 / 20 dB Pads, TNC
390XOPT646 390XOPT646 Motorola APX NEXT™ Series Auto- 67411 Scope Probe Kit
Test and Alignment Software (Requires 604) 10456 3920 Front / Rear Cover
91958 390XOPT629 Tait P25 Series Auto-Test ONLY 63928 DC to AC Converter, 12 VDC to 110-120 VAC
(Requires Opt218, 061)
9149 Antenna (BNC) (50 MHz)
DMR Radios 82556 Attenuator (6 dB / 150 Watts), 1.5 GHz

83384 390XOPT401 Auto-Test II Environment for DMR 82557 Attenuator (10 dB / 150 Watts), 1.5 GHz
Radio Systems (Requires Opt400) 58520 50 Ohm 250 Watts 5 GHz Termination
91705 390XOPT626 DMR Repeater Auto-Test Software 140309 3920 Return Loss Bridge Kit
(Requires Opt401, 061) 64009 3920 Microphone
91957 390XOPT628 Hytera DMR Series Auto-Test and 63351 RF Cable for AutoAlignment (COAX ASSY, RG223,
Alignment Software (Requires Opt401, 061) 36.0, BNC, M, ST / BNC, M, ST)

141994 390XOPT642 Hytera DMR Repeater Auto-Test 63927 Survey Technologies Inc (STI) Site Survey Package
(Requires Opt628) (Software & GPS Antenna)

89818 390XOPT610 Motorola MOTOTRBO Radio Series

Auto-Test and Alignment Software (Requires Extended Warranties
Opt401, 061 & 112277)
84349 3920 1 Year Extended Hardware Warranty + ANSI
141377 390XOPT639 Tait DMR Series Auto-Test ONLY No-Cert Calibrations
(Requires Opt400, 401, 061) 84350 3920 1 Year Extended Hardware Warranty +
dPMR Radios Certified Calibrations
89738 3920 2 Year Extended Hardware Warranty + ANSI
84415 390XOPT421 Auto-Test II Environment for dPMR
No-Cert Calibrations
Radio Systems (Requires Opt420)
89741 3920 2 Year Extended Hardware Warranty +
NXDN Radios Certified Calibrations
84351 3920 3 Year Extended Hardware Warranty + ANSI
84417 390XOPT441 Auto-Test for NXDN Radio Systems
No-Cert Calibrations
(Requires Opt440)
84352 3920 3 Year Extended Hardware Warranty +
112987 390XOPT632 Icom NXDN Series Auto-Test Certified Calibrations
(Requires Opt441, 061)

91960 390XOPT631 Kenwood NEXEDGE Series Auto-Test Calibration Certificates

and Alignment Software (Requires Opt441, 061)
83482 CALFB392X 3920 Calibration Certificate (ISO 9001)
ARIB T98 Radios

84419 390XOPT461 Auto-Test II Environment for ARIB T98

Radio Systems (Requires Opt460)

Multi-Protocol Radios

141378 390XOPT640 Kenwood NX-3000 / 5000 Series

Auto-Test and Alignment Software (Requires
Opt200 / 218, Opt400 / 401 and / or Opt440 / 441
depending on radio digital technology selected)

Languages

84410 390XOPT090 3920 Chinese GUI

12 3920B Data Sheet

 Contact Us +1 316 522 4981 © 2022 VIAVI Solutions Inc.
[email protected] Product specifications and descriptions in this
document are subject to change without notice.
To reach the VIAVI office nearest you, visit Patented as described at
VIAVI Solutions viavisolutions.com/contact viavisolutions.com/patents
3920B-ds-rts-nse-ae
30187471 904 0222
viavisolutions.com