PRODUCT DATA SHEET

SikaBit® PRO P-40-0 Sand

Plastomeric Modified Bituminous Waterproofing Membrane

DESCRIPTION CHARACTERISTICS / ADVANTAGES

SikaBit® PRO P-40-0 Sand is an APP modified, bitumin- ▪ Good watertightness
ous, torch-applied, waterproofing membrane. It is re- ▪ Good elongation and cold flexibility
inforced with a dimensionally stable non-woven poly- ▪ Good mechanical properties (tensile, tear, shear)
ester inlay. The underside has a thin polyethylene ▪ Good resistance to impact
burn-off film for easy application. It can be applied to ▪ Easy to install by torching method
wood, metal and concrete substrates including over ▪ Choice of primers to suit substrate and weather con-
existing bitumen roofing membranes. Top surface fin- ditions
ish: sand. Thickness: ~4,0 mm

USES
Waterproofing membrane for:
▪ Damp proofing of the exterior walls of basements
against percolating water and damp soil
▪ Flat roofs under protective layers or ballast
▪ Balconies and terraces under tiles
▪ Wet areas
▪ Protection of various substrates in a wide range of
applications

PRODUCT INFORMATION
Composition APP modified bitumen
Reinforcing material Non-woven polyester fabric
Packaging Roll size
Length 10,00 m
Width 1,00 m

Appearance / Colour Top surface Sand

Backing Polyethylene film

Shelf life 12 months from date of production

Storage conditions Product must be stored in original unopened and undamaged sealed pack-
aging in dry conditions and temperatures between +5 °C and +35 °C. Store
in a vertical position. Do not stack pallets of the rolls on top of each other,
or under pallets of any other materials during transport or storage. Always

Product Data Sheet

SikaBit® PRO P-40-0 Sand
August 2020, Version 01.01
020920011990000218

1/3
 refer to packaging.
Length 10 m
Width 1m
Effective thickness 4,0 mm ± 5 % (EN 1849-1)

TECHNICAL INFORMATION
Resistance to impact ≥ 600 mm at +23 °C (EN 12691- Method A)

Tensile strength Longitudinal 600 N/50 mm ± 20 % (EN12311-1)

Transversal 400 N/50 mm ± 20 %

Elongation Longitudinal 30 % ± 15 % (EN12311-1)

Transversal 30 % ± 15 %

Tear strength Longitudinal 150 N ± 30 % (EN 12310-1)

Transversal 150 N ± 30 %

Joint shear resistance Longitudinal Min. 500 N/50mm (EN 12317-1)

Transversal Min. 350 N/50mm

Flow resistance ≥ 120 °C (EN 1110)

Watertightness 60 kPa (EN 1928-Method B)

APPLICATION INFORMATION
Ambient air temperature +5 °C min. / +50 °C max.
Relative air humidity 80 % max
Substrate temperature +5 °C min. / +50 °C max.

APPLICATION INSTRUCTIONS Alignment

Unroll, align and re-roll correctly before torching.
SUBSTRATE QUALITY Overlaps
Side: 80 mm. End: 150 mm.
The supporting structure must be of sufficient struc- Torching
tural strength to apply all new and existing layers of Use a gas burner to heat the substrate and the backing
the waterproofing build-up. When used as a roofing film on the underside of membrane. When the back-
membrane, the complete roof system must be de- ing film starts to melt, the membrane is ready to stick.
signed and secured against wind uplift loadings. Roll the membrane forward and press firmly against
The substrate must be uniform, firm, smooth and free the substrate to bond. Ensure a bead of melted bitu-
of any sharp protrusion or burrs, clean, dry, free of men is visible along the full length of the overlap sides
grease, bitumen, oil, dust and loosely adhering and ends when laying.
particles. Detailing
All details such as internal and external corners, up-
APPLICATION METHOD / TOOLS stands, vent pipes, drains, support metalwork etc.
must be cut and sealed effectively. Detailing must fol-
Installation procedure low the recommended guidelines and good practice
Strictly follow installation procedures as defined in for torch-applied membranes.
method statements, application manuals and working Protection
instructions which must always be adjusted to the ac- The membrane must be protected from damage dur-
tual site conditions. ing any ongoing site activities.
Priming
Apply the appropriate primer at the correct consump-
tion to the prepared dry surface and allow to dry be-
fore next application stage. Refer to the individual
Product Data Sheets.

Product Data Sheet

SikaBit® PRO P-40-0 Sand
August 2020, Version 01.01
020920011990000218

2/3
MAINTENANCE ECOLOGY, HEALTH AND SAFETY
To maintain the function of the waterproofing during REGULATION (EC) NO 1907/2006 - REACH
its lifespan, it is advisable to arrange periodically for
inspection of the membrane and detailing. Check the This product is an article as defined in article 3 of regu-
functionality of the auxiliary works, flashings, drainage lation (EC) No 1907/2006 (REACH). It contains no sub-
outlets, overflow pipes etc. including removing leaves, stances which are intended to be released from the
moss and other vegetation. article under normal or reasonably foreseeable condi-
tions of use. A safety data sheet following article 31 of
IMPORTANT CONSIDERATIONS the same regulation is not needed to bring the
product to the market, to transport or to use it. For
▪ At low temperatures, take care unrolling to avoid safe use follow the instructions given in the product
damaging the membrane. data sheet. Based on our current knowledge, this
▪ Use suitable footwear to avoid puncturing the mem- product does not contain SVHC (substances of very
brane. high concern) as listed in Annex XIV of the REACH reg-
▪ Do not apply to wet, damp or unclean surfaces. ulation or on the candidate list published by the
▪ Do not over-torch the membrane otherwise the European Chemicals Agency in concentrations above
polyester reinforcement (which melts at 260 °C) will 0,1 % (w/w).
be damaged making the membrane un-useable.
▪ If membrane is insufficiently heated, this can cause LEGAL NOTES
reduced adhesion to the substrate, between layers
or on the overlaps. If this occurs, un-bonded areas The information, and, in particular, the recommenda-
must be lifted and re-torched. tions relating to the application and end-use of Sika
▪ If a seasonal symbol is printed on the roll’s label, it is products, are given in good faith based on Sika's cur-
advisable to use the membrane during the indicated rent knowledge and experience of the products when
season. properly stored, handled and applied under normal
conditions in accordance with Sika's recommenda-
BASIS OF PRODUCT DATA tions. In practice, the differences in materials, sub-
strates and actual site conditions are such that no war-
All technical data stated in this Data Sheet are based ranty in respect of merchantability or of fitness for a
on laboratory tests. Actual measured data may vary particular purpose, nor any liability arising out of any
due to circumstances beyond our control. legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
LOCAL RESTRICTIONS mendations, or from any other advice offered. The
user of the product must test the product’s suitability
Note that as a result of specific local regulations the for the intended application and purpose. Sika re-
declared data and recommended uses for this product serves the right to change the properties of its
may vary from country to country. Consult the local products. The proprietary rights of third parties must
Product Data Sheet for exact product data and uses. be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request.

PT. Sika Indonesia Head Office and

Manufacturing
Jl. Raya Cibinong-Bekasi Km.20
Limusnunggal-Cileungsi
Bogor 16820-Indonesia
Tel. +62 21 8230025, Fax +62 21
8230026

SikaBitPROP-40-0Sand-en-ID-(08-2020)-1-1.pdf

Product Data Sheet

SikaBit® PRO P-40-0 Sand
August 2020, Version 01.01
020920011990000218

3/3