Overview

RCU Room Control Unit (See Figure 1) is the core of a hotel system. It supports hotel host control, mix module control, 24-channel dry
contacts, doorbell status display and LED output. The RCU Room Control Unit has 48 channels, which must be set through HDL Hotel
HDL-MHRCU.433 Room Management System. The RCU Room Control Unit can monitor and control each equipment via HDL Hotel Room Management
System after setting targets as doorbell panels, curtains, lamps, ventilation fan, air conditioners and other equipment.
RCU Room Control Unit
Functions
■ Controls up to 48 channels, each channel has the parameter for lower limit, higher limit, the maximum limit.
■ There are 99 scenes in total, each scene’s running time is 0-250 seconds.
■ The protection delay time of each channel is 0-60 minutes.
Datasheet ■ 0-250s of bulk power-on time for each channel.
■ Activate corresponding scene according to card master after identification.
Issued: April 26, 2019 ■ Monitors and controls air conditioners, curtains, lightings, room status, and uploads the status of air conditioners, curtains,
Edition V1.0.0 lightings and other states to the monitor software of the server in real time.
■ Receive various panel control signal, and control the module and channels.
■ Bidirectional data exchange between HDL Buspro and Ethernet.
■ Network connection. The RCU Room Control Unit has a RJ45 port, which can connect to each room, reception and manage-
ment software. Through HDL Hotel Room Management System, the module can integrate with the third party management
software to exchange information.
Mix control functions
■ Channel 1 to 13 are relay outputs, each channel is 5A. The load types are incandescent lamp, halogen lamp, low voltage halo-
gen lamp.
■ Channel 14 to 17 are relay outputs, each channel is 10A. The load types are incandescent lamp, halogen lamp, low voltage
halogen lamp.
■ Channel 18 to 21 are dimming outputs, each channel is 0.8A. It has short circuit protection, and the fuse is easy to replace. If the
channel is short circuit or the fuse is wrong, the fuse indicator will flash.
■ Channel 22 is relay for doorbell, it can control the doorbell status.
Dry contract
■ 24-channel dry contract inputs. (The control target should be set from IHMS)
Door bell function
Figure 1. RCU Room Control Unit ■ 5-channel LED outputs. (It can connect to the third-party door bell panel.)
LED output function
■ 6-channel switch indicator outputs.

Important Notes
216mm ■ Inner Buspro cable - CAT5E or dedicated HDL Buspro cable.
■ The fuse must be aR type.
■ When you replace the fuse, the power should be cut off.
■ Channel 18 to 21 are TRIAC dimming outputs. When the load is flickering, the constant current module needs to be connected.
90mm

Product Information
Dimensions - See Figure 2 - 3
Wiring - See Figure 4
5CH LED indicators, it can connect with third-party doorbell.
Figure 2. Dimensions - Front View Universal switches for 1-5:
1. Wait, universal switch number is 13.
2. DND, universal switch number is 14.
3. Clean/laundry, universal switch number is 15.
4. Room number, universal switch number is 16.
56mm 5. Bell, universal switch number is 17.
A1: LED indicators of 5CH doorbell
A2: Doorbell control
A3: The recommended resistor is 1kΩ - 5kΩ.
A4: 6CH common switch LED display. When the dry contact closes, the LED will be on, otherwise, the LED will be off.
A5: 24CH dry contacts
A6: RJ45 port
A7: Button and indicator: The indicator flickers in green when the module is working properly. Keep pressing it for 2s, you can set the
start channel. Keep pressing it for 10s, it will turn red, the module will be reset to factory setting.
Default setting parameters:
IP: 192.168.10.250
Router IP: 192.168.10.1
Port: 6006
Figure 3. Dimensions - Side View The network segment of the module should be same as the PC.
A8: Fuse socket
A9: Indicator of fuse

Installation - See Figure 5 - 7

Step 1. Fix the DIN rail with screws.
A1
Step 2. Buckle the bottom cap of the RCU Room Control Unit on the edge of the DIN rail.
A2
Step 3. Press the device on the DIN rail, slide it and fix it up until an appropriate position is adjusted.
A3

Safety Precautions
A4

■ The installation and commissioning of the device must be carried out by HDL or the organization designated by HDL. For plan-
A5 ning and construction of electric installations, the relevant guidelines, regulations and standards of the respective country are to
A8 A9 be considered.
CH22
A6 ■ The device should be installed with DIN rail in DB box. HDL does not take responsibility for all the consequences caused by
A7 installation and wire connection that are not in accordance with this document.
■ Please do not privately disassemble the device or change components, otherwise it may cause mechanical failure, electric
N
shock, fire or body injury.
RS485 Inner HDL
L
interface
for third-
Buspro Buspro ■ Please resort to our customer service department or designated agencies for maintenance service. The warranty is not applica-
party
device
ble for the product fault caused by private disassembly.
Figure 4. Wiring

Package Contents
HDL-MHRCU.433*1 / Label*5 / Datasheet*1
1/2
 Technical Data
Basic Parameters
Working voltage 20~30V DC

Working current 300mA/24V DC

Input voltage AC100-240V (50/60Hz)

图5

Relay output 5A/10A

Communication interface HDL Buspro, RJ45, Inner Buspro

1 RJ45 interface UDP/IP network Interface

TRIAC 16A TRIAC, minimum load is 30W

Cable diameter of Buspro terminal 0.6-0.8mm

External Environment
Working temperature -5℃~45℃

Working relative humidity ≤90%

Storage temperature -20℃~60℃

Storage relative humidity ≤93%

图6
Specifications
Dimensions 216mm×90mm×56mm

Net weight 725g

2 Housing material Nylon

35mm DIN rail installation

Installation
(See Figure 5 - 7)

Protection rating (Compliant with EN 60529) IP20

Name and Content of Hazardous Substances in Products

Hazardous substances

Components Poly-brominated Poly-brominated

Lead Mercury Cadmium Chromium VI
Figure 7 biphenyls diphenyl ethers
(Pb) (Hg) (Cd) (Cr (VI))
(PBB) （PBDE）
Figure 5 – 7. Installation
Plastic o o o o o o

Hardware o o o o - -

Screw o o o × - -

Solder × o o o - -

PCB × o o o o o

IC o o o o × ×

The symbol “-” indicates that the hazardous substance is not contained.
The symbol "o" indicates that the content of the hazardous substances in all the homogeneous materials of the component is below the
limit requirement specified in the Standard IEC62321-2015.
The symbol “×” indicates that the content of the hazardous substance in at least one of the homogeneous materials of the part exceeds
the limit requirement specified in the Standard IEC62321-2015.

HDL Buspro Cable Guide

Inner Buspro HDL Buspro Cable CAT5/CAT5E

DATA+ Yellow Blue/Green

DATA- White Blue white/Green white

Technical support
COM Black Brown white/Orange white
E-mail: [email protected]
Website: https://www.hdlautomation.com 24V DC Red Brown/Orange

©Copyright by HDL Automation Co., Ltd. All rights reserved.

Specifications subject to change without notice.
2/2