Scribd
Upload
132 views

Assignment & Project For Hydropwer Engineering

This document assigns student groups and river basins to study existing and planned hydropower projects in Ethiopia, including pre-feasibility, feasibility, design, construction, and operation. The groups are to conduct detailed studies of hydraulics, hydrology, intake structures, tunnels, forebays, penstocks, powerhouses, turbines, power production, and construction costs for hydropower systems in their assigned river basins. A final report is due on June 15th and will be graded out of 30% for an MSc hydraulic engineering extension course.

Uploaded by

ashenafi negus
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
132 views

Assignment & Project For Hydropwer Engineering

This document assigns student groups and river basins to study existing and planned hydropower projects in Ethiopia, including pre-feasibility, feasibility, design, construction, and operation. The groups are to conduct detailed studies of hydraulics, hydrology, intake structures, tunnels, forebays, penstocks, powerhouses, turbines, power production, and construction costs for hydropower systems in their assigned river basins. A final report is due on June 15th and will be graded out of 30% for an MSc hydraulic engineering extension course.

Uploaded by

ashenafi negus
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

WOLO UNIVERSITY

KOMBOLCHA INSTITUTE OF TECHNOLOGY


DEPARTMENT OF HYDRAULIC AND WATER RESOURCES ENGINEERING

Hydropower Engineering (HE – 7023) Assignment

Section: (MSc in Hydraulic Engineering, Regular)


Submission date: June 10, 2022 Max Marks: 30%
Submitted to: Dr Fikru F. ([email protected])

1) For the10 year monthly stream flow data given table below, determine the Flow Duration
Curve (FDC) by using
a) Class Interval Method
b) Total period approach, and
c) Calendar year approach.

And indicate the catchment characteristics and its suitability for hydropower development

2) Based on the above data shown in equation 1 construct the power duration curve if the
available head is 20 m. Calculate the average potential power and the technically available
power with conveyance efficiency of 70% and overall efficiency of 80%.
3) What are the types of turbines suitable under the following conditions: (a) high head and
low discharge (b) medium head and medium discharge and (c) low head and large
discharge?
4) A generating station has a maximum demand of 25 MW, a load factor of 60%, a plant
capacity factor of 50% and a plant use factor of 72%. Find

i. The reserve capacity of the plant

ii. The daily energy produced and

iii. Maximum energy that could be produced daily if the plant, while running as
per the schedule, were fully loaded.

5) A surge chamber 8m in diameter is situated at the downstream end of a low-pressure tunnel


10km long and 3m in diameter. At a steady discharge of 36m3/s the flow of the turbines is
suddenly stopped by closure of the turbine inlet valves. Determine the maximum rise level
in the surge chamber and its time of occurrence.
6) The jet velocity in a Pelton turbine is 65 m/s. The peripheral velocity of the runner is 25
m/s. The jet is deflected by 160° by the bucket. Determine the power developed and
hydraulic efficiency of the turbine for a flow rate of 0.9 m3/s. The blade friction coefficient
is 0.9.
7) The outer diameter of a Francis runner is 1.4 m. The flow velocity at inlet is 9.5 m/s. The
absolute velocity at the exit is 7 m/s. The speed of operation is 430 rpm. The power
developed is 12.25 MW, with a flow rate of 12 m3/s. Total head is 115 m. For shockless
entry determine the angle of the inlet guide vane. Also find the absolute velocity at entrance,
the runner blade angle at inlet and the loss of head in the unit. Assume zero whirl at exit.
Also, fluid the specific speed.
8) At a location selected to install a hydroelectric plant, the head is estimated as 550 m. The
flow rate was determined as 20 m3/s. The plant is located at a distance of 2 m from the
entry to the penstock pipes along the pipes. Two pipes of 2 m diameter are proposed with
a friction factor of 0.029. Additional losses amount to about 1/4th of frictional loss.
Assuming an overall efficiency of 87%, determine how many single jet unit running at
300 rpm will be required.
WOLO UNIVERSITY
KOMBOLCHA INSTITUTE OF TECHNOLOGY
DEPARTMENT OF HYDRAULIC AND WATER RESOURCES ENGINEERING

Hydropower Engineering (HE – 7023) Project

Section: (MSc in Hydraulic Engineering, Extension)


Submission date: June 15, 2021 Max Marks: 30%
Submitted to: Dr Fikru F. ([email protected])

✓ Assigned groups and respective river basins


S. N Name Groups River Basin
1 Tale Upper Blue Nile (Abay, Baro-Akobo
2 Ayalew Group -1 and Tekeze basins)
3 Ermias Degu
4 Milashu Group -2 Omo-Gibe and Awash River Basins
5 Nuria and Ermias
Ambaye
6 Ashenafi Group -3 Wabishebele and Genale-Dawa River
7 Degu basins
8 Juhar

Discuss all details of existing and planned hydropower projects systems components in Ethiopian River
basins using masterplan studies and other sources based on the above formulated groups including pre-
feasibility, feasibility, detail design, construction, operation and maintenance studies. The assignment
should include the detail study and designs of Hydraulics and Hydrology and Hydropower intake
structures, Head race tunnels, Forebays and surge tanks, Penstocks, power houses, tailrace tunnels,
turbine selection and settings, cavitation, power production potential, construction costs (detail BOQ)
and other components.

You might also like