Scribd
Upload
85 views15 pages

2G Card Configuration

This document provides instructions for configuring 2G card parameters such as static IP, VLAN ID, and routing in a BTSM software. It involves setting the BTS IP address, BSC IP address, VLAN ID, and subnet mask based on plan parameters. It also requires configuring the port IP by selecting the rack, sub-rack, slot and port numbers and specifying the BTS IP and subnet mask. Finally, it describes configuring the route by selecting the rack and sub-rack numbers and providing the next hop IP address, BSC IP, and route priority.

Uploaded by

Rana Raj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views15 pages

2G Card Configuration

This document provides instructions for configuring 2G card parameters such as static IP, VLAN ID, and routing in a BTSM software. It involves setting the BTS IP address, BSC IP address, VLAN ID, and subnet mask based on plan parameters. It also requires configuring the port IP by selecting the rack, sub-rack, slot and port numbers and specifying the BTS IP and subnet mask. Finally, it describes configuring the route by selecting the rack and sub-rack numbers and providing the next hop IP address, BSC IP, and route priority.

Uploaded by

Rana Raj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

{*2G CARD CONFIGURATION*}

Rana_2022

TELETALK BANGLADESH LTD.


 Ping Test
192.168.0.72

General LAN  Laptop IP


192.168.0.50
BTSM Software Folder

Click
btsm.exe
admin

hwbs@com /
Y5$7Kc@u#$tr&LhF

192.168.0.72
Click >> “IP over FE Static IP”

“Static IP” window will


appear
Configure BTS, BSC & VLAN

 Select static IP
status “Enable”
 Put BTS IP address as
 Select Com per plan [ Payload_BTS Local IP
Type “Port IP” Address(IP path) ]

 Put BSC IP address as per


plan [RNC/BSC FG2C (Main) IP Address ]
 Select VLAN Flag
“Enable” as per  VLAN Pri “0”
plan by default

 Put VLAN ID as
per plan [ Payload VLAN ID ]
 Click “OK” after
all parameter set
Configure BTS, BSC & VLAN

 Tab “Static
Query” page

 All setting parameters


will appear after Click
“OK”

 Click “OK”
Configure Port IP

Select Rack no. Select Sub Rack Select Slot no.


“0” (as per plan) no. “0” (as per plan) “6” (as per plan)

 Select Port  Port no. “0”


Type “Ethernet as per
Port” connection

 Put BTS IP address as  Put BTS Subnet Mask as


per plan [ Payload_BTS Local IP
Address (IP path) ]
per plan [ Subnet Mask PLD ]

 Click “OK” after


all parameter set
Configure Port IP

 Tab “Static Query”


page

 All setting parameters


will appear after Click
“OK”

 Click “OK”
Configure Route

Select Rack Select


no. “0” (as Route Type
per plan) “Next”
Select Sub
Rack no. “0”
(as per plan)

Select Slot
no. “6” (as
per plan)  Put Next Hop IP Address
as per plan [ Gateway IP
Address PLD ]

 Select Route
 Put BSC IP address [ BSC .
Pri “60” (as per
 Put BSC Subnet Mask IP with last octate as “0” ] plan)
[BSC subnet mask with last octate
as “0” ]

 Click “OK” after


all parameter set
THANK YOU

You might also like