Safety Data Sheet: Section 1 - Product and Company Identification

DOC.
NO GO-SDS-42
Safety Data Sheet VER. NO A.2
PAGE. NO 1/4
SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

 Product Name
Trade Name : Radiator Coolant
 Manufacturer / Supplier : GIBSON OIL SDN. BHD.
No. 15, Jalan Bukit 24, Bandar Seri Alam, 81750 Masai, Johor.
SECTION 2 – COMPOSITION / INFORMATION ON INGREDIENTS

 Product type
Coolant
 Composition / Information on ingredient
Components Cas No of Components
MEG 12 – 15% 203-473-3
SECTION 3 – HAZARDS IDENTIFICATION

 Health Hazard
May cause an allergic skin reaction.
 Environmental Hazard
This preparation does not require classification on the basic of environment hazard.
 Physical and Chemical hazards / Fire and Explosion hazards.
Low hazard, material can from flammable mixture or can burn only heating to temperatures at or above the flash
point. . See section 9 “PHYSICAL AND CHEMICAL PROPERTIES”.
Decomposes flammable and or toxic gases will form upon decomposition. See Section 10” STABILITY AND
RECTIVITY”. Toxic gases will form upon combustion. See section 5: Fire-Fighting measures”.
SECTION 4 – FIRST AID MEASURES

 Inhalation
Remove patient to a clean atmosphere and administer oxygen if it is necessary. Consult a physician immediately.
 Skin Contact
Immediately flush with large amounts of water, use soap if available. Remove grossly contaminated clothing
including shoes and launder before reuse.
 Eye Contact
Immediately flush eyes with large amounts of water or at least 15 minute. Get prompt medical attention. DO NOT
attempt to give anything by mouth to an unconscious person.
Office Tel: +607-3822112 Office Fax: +607-3824322 E-mail: [email protected] Website: www.gibsonoil.com
DOC. NO GO-SDS-42
PAGE. NO 2/4
SECTION 5 – FIRE FIGHTING MEASURES

 Fire Fighting Produces
Use water spray cool fire exposed surfaces and to protect personnel.
Shut off “fuel” to fire.
Use dry chemical powder, foam, carbon dioxide (CO²) or water fog to extinguish fire.
 Special fire precautions
Respiratory and eye protection required for the fire fighting personnel. See also Section 4 “First Aid Measures” as
well as Section 10 “Stability and Reactivity” Hazardous Combustion Product: Fumes, smoke, Carbon Dioxide (CO2).
SECTION 6 – ACCIDENTAL RELEASE MEASURES

 Land Spill
Contain spill liquid with sand or earth.
Recover by pumping (use an explosion proof or and hand pump) or with a suitable absorbent. If liquid is too viscous
for pumping, scrape up with shovels or pails and place in suitable containers for recycle or disposal.
Consult and expert on disposal of recovered material and ensure conformity to local disposal regulations.
See section 4 “FIRST AID MEASURES” as well as Section 10 “STABILITY AND REACTIVITY”.
 Water spill
Warn other shipping. Notify port or relevant authority and keep public away. Shut off sources if possible to do
without hazard. Confine if possible. Remove from surface by skimming or with suitable absorbents. If swallowed by local
authorities and environment agencies sinking and or suitable dispersants may be used in non-confined waters.
Consult an expert on disposal of any recovered material and ensure conformity to local disposal regulations.
See also section 4 “FIRST AID MEASURES” as well as Section 10 “STABILITY AND REACTIVITY”.
SECTION 7 – HANDLING AND STORAGE

 Storage Temperature (°C) : between 10 to 40.
 Transport Temperature (°C) : between 10 to 40.
 Loading/Unloading Temperature (°C) : between 10 to 40.
 Storage transport pressure : Atmospheric.
 Usual shipping containers : Tanker tank cars, tank truck, drums, pails
 Material and coating suitable : Stainless steel, inorganic zinc coatings, amine epoxy coatings, nitrile rubber, rubber.
 Material and coating unsuitable : Compatibility with plastic material can vary we therefore recommended that
compatibility is test prior to use.
 Storage / Handling general notes : Keep container closed. Handle containers with care. Open slowly in order to
control possible pressure release. Store in a cool well-ventilated place away from incompatible materials.
 Do not handle store or open near an open flame, sources of heat of sources of ignition protect material from
direct sunlight
 Do not pressurize cut head or weld containers. Empty produce residue. Do not reuse empty containers without
commercial cleaning or reconditioning.
SECTION 8 – EXPOSURE CONTROLS / PERSONAL PROTECTION

 Engineering Control Measures / Ventilation :
The use of local exhaust ventilation is recommended to control process emissions near the source. Provide
mechanical ventilation of confined space, see respiratory protection recommendation.
 Personal protection :
For open systems where contact is likely, wear long sleeves, chemicals resistant gloves and chemicals goggles.
 Where prolonged contact may occur. Wear long sleeves sand safety glasses with side shields.
DOC. NO GO-SDS-42
PAGE. NO 3/4
 Where concentration in air may be exceedingly high and engineering, work practice or other means of exposure
reduction are not adequate approve respirator may be necessary to prevent over-exposure by inhalation.
SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES

 Product typical
NO. PARAMETES TEST METHODS SPECIFICATION
1 Boiling Point (°C) ASTM 97.3°C
2 Freezing Point (°C) ASTM -5°C
3 PH of concentrate ASTM 9 +/- 0.5
4 Appearance ASTM Fluorescent green
This product is soluble

5 Soluble in water ASTM
in water
6 Specific Gravity (H²0=1) ASTM -1.2
7 Density ASTM 1.0
Attention : The data below are typical values and do not constitute a specification.
SECTION 10 – STABILITY AND REACTIVITY

 Hazardous polymerization: No.
 Stability: Stable.
 Conditions to avoid instability: Temperature above 60°C.
 Materials and conditions to avoid incompatibility: Water, strong oxidizing agents.
SECTION 11 – TOXICOLOGICAL INFORMATION

 Acute Inhalation: Negligible hazard at ambient (-18 to 38°C) or recommended blending temperature.
 Skin Contact: Low order of toxicity. May be slight irritating
 Eye contact: Slight irritating and may injure eye tissue if not removed promptly.
 Ingestion: Minimal toxicity.
SECTION 12 – DISPOSAL CONDIDERATIONS

The following advice only applies to the products as supplied. Combination with other material may
well indicate another route of disposal. If in doubt contact the local supplier or authorities:
 Empty drums should be taken for recycling, recovery or disposal through.
 A suitable qualified or licensed contractor.
DOC. NO GO-SDS-42
PAGE. NO 4/4
 Care should in any case to be taken to ensure compliance with national.

 And local regulations.
The products are not suitable for disposal by either landfill or via municipal sewers drain natural stream or rivers. They
will generate ash if burned and can be burned directly in appropriate equipment. The products are suitable for energy recovery
in appropriate incinerators.
SECTION 13 – TRANSPORT INFORMATION

 UN CLASS : Not classified.
 A DR / RID-Class : Not classified.
 A DR / RID-Hazard Identification Number : Not classified.
 IMDG-Class : Not classified.
 IATA-Class : Not classified.
SECTION 14 – REGULATORY INFORMATION

 Regulatory Information
EC Classification: Not classified.
R phrases: Not classified.
S phrases: Not classified.
EC Annex Number: Not listed.
FDA List Number: Not listed.
SECTION 15 – OTHER INFORMATION

Heating for the product is usually not necessary expert in situations as described below. With proper facilities, no
heating is required for pumping at ambient temperatures. If extreme cold weather conditions necessitate heating, then
tempered water or oil not exceeding 100°C is recommended. If heated product temperature should be container above
60°C. Product should be stored between 10 and 40°C (40 to 100°F) . Lower temperatures may result in some
crystallization of the product. Higher temperatures will lead to degradation of product quality.

Safety Data Sheet: Section 1 - Product and Company Identification

Uploaded by

Copyright:

Available Formats

Safety Data Sheet: Section 1 - Product and Company Identification

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Safety Data Sheet: Section 1 - Product and Company Identification

Uploaded by

Copyright:

Available Formats

DOC.

Safety Data Sheet VER. NO A.2

SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

SECTION 2 – COMPOSITION / INFORMATION ON INGREDIENTS

SECTION 3 – HAZARDS IDENTIFICATION

SECTION 4 – FIRST AID MEASURES

Safety Data Sheet VER. NO A.2

SECTION 5 – FIRE FIGHTING MEASURES

SECTION 6 – ACCIDENTAL RELEASE MEASURES

SECTION 7 – HANDLING AND STORAGE

SECTION 8 – EXPOSURE CONTROLS / PERSONAL PROTECTION

Safety Data Sheet VER. NO A.2

SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES

NO. PARAMETES TEST METHODS SPECIFICATION

1 Boiling Point (°C) ASTM 97.3°C

2 Freezing Point (°C) ASTM -5°C

3 PH of concentrate ASTM 9 +/- 0.5

4 Appearance ASTM Fluorescent green

This product is soluble

6 Specific Gravity (H²0=1) ASTM -1.2

7 Density ASTM 1.0

SECTION 10 – STABILITY AND REACTIVITY

SECTION 11 – TOXICOLOGICAL INFORMATION

SECTION 12 – DISPOSAL CONDIDERATIONS

Safety Data Sheet VER. NO A.2

 Care should in any case to be taken to ensure compliance with national.

SECTION 13 – TRANSPORT INFORMATION

SECTION 14 – REGULATORY INFORMATION

SECTION 15 – OTHER INFORMATION

You might also like